Sony HT-XT1 Owner’s Manual

Home Theatre

System

Operating Instructions

Mode d'emploi

Manual de instrucciones

Owner's Record

The model and serial numbers are located on the rear panel of the unit.

Record the serial numbers in the space provided below. Refer to them whenever you call upon your Sony dealer regarding this product.

Model No. HT-XT1

Serial No.

To reduce the risk of fire or electric shock, do not expose this

apparatus to rain or moisture.

The unit is not disconnected from the mains as long as it is connected to the AC outlet, even if the unit itself has been turned off.

To reduce the risk of fire, do not cover the ventilation opening of the

appliance with newspapers, tablecloths, curtains, etc. Do not expose the appliance to naked flame sources (for example, lighted candles).

To reduce the risk of fire or electric shock, do not expose this appliance to dripping or splashing, and do not place objects filled with liquids, such

as vases, on the appliance.

As the main plug is used to disconnect the unit from the mains, connect the unit to an easily accessible AC outlet. Should you notice an

abnormality in the unit, disconnect the main plug from the AC outlet immediately.

Do not install the appliance in a confined space, such as a bookcase or built-in cabinet.

For the customers in the U.S.A

This symbol is intended to alert the user to the presence of

uninsulated "dangerous voltage" within the product's enclosure

that may be of sufficient magnitude to constitute a risk of

electric shock to persons.

This symbol is intended to alert the user to the presence of

important operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

Important Safety Instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

Do not expose batteries or appliances with battery-installed to excessive heat, such as sunshine and fire.

Indoor use only.

2us

12)Useonlywiththecart,stand,tripod,bracket,ortablespecifiedbythe manufacturer,orsoldwiththeapparatus.Whenacartisused,use cautionwhenmovingthecart/apparatuscombinationtoavoidinjury fromtip-over.

13)Unplugthisapparatusduringlightningstormsorwhenunusedfor longperiodsoftime.

14)Referallservicingtoqualifiedservicepersonnel.Servicingisrequired whentheapparatushasbeendamagedinanyway,suchaspower- supplycordorplugisdamaged,liquidhasbeenspilledorobjects havefallenintotheapparatus,theapparatushasbeenexposedto rainormoisture,doesnotoperatenormally,orhasbeendropped.

ThefollowingFCCstatementappliesonlytotheversionofthismodel manufacturedforsaleintheU.S.A.Otherversionsmaynotcomplywith FCCtechnicalregulations.

NOTE: Thisequipmenthasbeentestedandfoundtocomplywiththelimitsfor

aClassBdigitaldevice,pursuanttoPart15oftheFCCRules.Theselimits aredesignedtoprovidereasonableprotectionagainstharmful interferenceinaresidentialinstallation.Thisequipmentgenerates,uses andcanradiateradiofrequencyenergyand,ifnotinstalledandusedin accordancewiththeinstructions,maycauseharmfulinterferenceto

radiocommunications. However,thereisnoguaranteethatinterferencewillnotoccurina

particularinstallation.Ifthisequipmentdoescauseharmfulinterference toradioortelevisionreception,whichcanbedeterminedbyturningthe equipmentoffandon,theuserisencouragedtotrytocorrectthe interferencebyoneormoreofthefollowingmeasures:

- Reorientorrelocatethereceivingantenna.

- Increasetheseparationbetweentheequipmentandreceiver.

- Connecttheequipmentintoanoutletonacircuitdifferentfromthatto

whichthereceiverisconnected.

- Consultthedealeroranexperiencedradio/TVtechnicianforhelp.

Properlyshieldedandgroundedcablesandconnectorsmustbeusedfor connectiontohostcomputersand/orperipheralsinordertomeetFCC

emissionlimits.

CAUTION

You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

This equipment must not be co-located or operated in conjunction with any other antenna or transmitter.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment has very low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation (MPE). But it is desirable that it should be installed and operated keeping the radiator at least 20cm or more away from person's body (excluding extremities: hands, wrists, feet and ankles).

continued

3us

For the customers in the Canada

Properly shielded and grounded cables and connectors must be used for connection to host computers and/or peripherals.

This device complies with Industry Canada licence-exempt RSS

standard(s). Operation is subject to the following two conditions: (1)this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

This equipment complies with IC radiation exposure limits set forth for an

uncontrolled environment and meets RSS-102 of the IC radio frequency (RF) Exposure rules.

This equipment has very low levels of RF energy that it deemed to comply

without maximum permissive exposure evaluation (MPE). But it is desirable that it should be installed and operated keeping the radiator at least 20cm or more away from person's body (excluding extremities: hands, wrists, feet and ankles).

4us

Useful functions

Using the Control for HDMI function .................................... 6

Using "BRAVlA" Sync features ............................................... 7

Controlling the system using a smartphone or tablet device

(SongPal) .......................................................................... 8

Adjusting the settings .......................................................... 10

Miscellaneous

Precautions ........................................................................... 12

BLUETOOTH wireless technology ........................................ 15

Troubleshooting ................................................................... 16

Parts and controls ................................................................ 19

Specifications ....................................................................... 21

Refer to the supplied Startup Guide for setup and basic operations.

5us

Using the Control for HDMI function

By using the Control for HDMI function, and connecting equipment that is compatible with the Control for HDMI function via a High

Speed HDMI cable, operation is simplified with the features below. The Control for HDMI function is enabled by setting "CTRL (Control for HDMI)" to "ON" (page 11). The default setting is "ON."

When you turn offthe TV, the system and the connected equipment will turn off automatically.

If you turn on the system while you are watching the TV, the TV sound will be output from the speakers of the system automatically.

The volume of the system will be adjusted when you adjust the volume using the TV's remote control.

If the TV sound was output from the speakers of the system the last time you watched the TV, the system will be turned on automatically

when you turn on the TV again.

If the TV is compatible with the Audio Return Channel (ARC)

technology, a High Speed HDMI cable connection will also allow

sending digital audio signals from the TV to the system. You do not need to make a separate audio connection for listening to TV sound

from the system. The ARC function is enabled by setting "ARC (Audio return channel)"

to "ON" (page 11).The default setting is "ON."

When you activate the equipment (Blu-ray Disc TM player,

"PlayStation.4," etc.) connected to the system with a High Speed HDMI cable, the connected TV is turned on automatically and the

input signal of the system is switched to the appropriate HDMI input.

• The above features may not operate with certain equipment.

• Depending on the settings of the connected equipment, the Control for HDMI function may not work correctly. Refer to the operating instructions of the equipment.

6us

Using "BRAVIA" Syncfeatures

The original Sony functions listed below can also be used with products that are compatible with "BRAVlA" Sync.

Ira "BRAVlA" Sync-compatible TV is connected to the system, the power consumption will be reduced in standby mode by stopping

HDMI signal transmission when the TV is turned off with the pass- through function* of the system set to "AUTO" (page 11). The default setting is "AUTO."

If any TV other than "BRAVlA" is connected, set the item to "ON" (page 11).

* The pass-through function for HDMI signals is used to output the

signals from the HDMI OUTjack of this system even if it is in standby mode.

ii ii i iiii HH ii i iiU!!! ii!!!ii! ii!!!ii! ii!!!ii i!iii!iii!iii iiii!!i ii i i!ii!i iii iii i!!ii! ii!!!ii! ii!!!ii! ii !iii ii iiii

• Use a High Speed HDMI cable. If you use a Standard HDMI cable, 1080p, Deep Color, 3D, and 4K images may not be displayed

properly.

• Use an HDMI-authorized cable.

Use a Sony High Speed HDMI cable with the Cable Type Logo.

• We do not recommend using an HDMI-DVl conversion cable.

• Check the setup of the connected equipment if an image is poor or

the sound does not come out of the equipment connected via the HDMI cable.

• Audio signals (sampling frequency, bit length, etc.) transmitted

from an HDMIjack may be suppressed by the connected equipment.

• Sound may be interrupted when the sampling frequency or the

number of channels of audio output signals from the playback equipment is switched.

• If the connected equipment is not compatible with copyright- protection technology (HDCP), the image and/or the sound from

the HDMI OUT jack of this system may be distorted or may not be

output. In such a case, check the specifications of the connected equipment.

• When "TV" is selected as the input source of the system, video signals via one of the HDMI IN 1/2/3 jacks selected last time are output from the HDMI OUT jack.

• This system supports Deep Color, "x.v.Color," 3D, and 4K

transmission.

• To enjoy 3D images, connect a 3D-compatible TV and video equipment (Blu-ray Disc player, "PlayStation,4," etc.) to the system

using High Speed HDMI cables, put on 3D glasses, and then play back a 3D-compatible Blu-ray Disc, etc.

• To enjoy4K images, the TV and players that are connected to the system must be compatible with 4K images.

7us

Controllingthe system usinga smartph0ne or tablet device(S0ngPal)

"SongPal" is the application to operate the system with your smartphone or tablet, etc.

"SongPal" is available from either Google Play TM or App Store. This function is enabled by setting "BT PWR (BLUETOOTH power)" to "ON" (page 11). The default setting is "ON."

I/(_ (on/standby) PAIRING

Illumination LED (blue) Display

Touch the I/(_ (on/standby) touch key of the system. The display of the system lights after the system turns on.

Search for "SongPal" with the Android device and download

that application,

Run "SongPal" then follow the on-screen instructions.

After the BLUETOOTH connection display appears on the Android device, touch the PAIRING touch key of this system.

The illumination LED (blue) of the system flashes quickly during BLUETOOTH pairing.

5 Select "SONY:HT-XTI" from the BLUETOOTH device list of the

Android device.

When the connection has been established, the illumination LED (blue) of the system lights.

6 Operate the system with the display of the connected

Android device.

8us

One-Touch connection using the Android device with the NFC function built-in (NFC)

Perform steps I to 3 of "When using an Android device."

After the BLUETOOTH connection display appears on the Android device, touch the Android device with the N mark of

the system.

When the connection has been established, the illumination LED (blue) of the system lights.

1 Touch the I/(_ (on/standby) touch key of the system.

The display of the system lights after the system turns on.

2 Touch the PAIRING touch key of this system.

The illumination LED (blue) of the system flashes quickly during

BLUETOOTH pairing.

Set the iPhone/iPod touch to pairing mode and select "SONY:HT-XTI" from the BLUETOOTH device list on the iPhone/iPod touch.

When the connection has been established, the illumination LED (blue) of the system lights.

Search for "SongPal" with the connected iPhone/iPod touch and download that application.

Run "SongPal" then operate the system with the display of

the iPhone/iPod touch.

Illumination LED (blue)

3 Operate the system with the display of the Android device.

9us

Adjusting the settings

\ [/(b

_PUT _'_

UT[NG //

V0L

OUND "_.

[ELD -'_,

OICE /

m_Tul_r_

_E_R

,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,MENU

÷ 4, (select)

ENTER RETURN

You can set the following items with the MENU button on the remote control. Your settings are retained even if you disconnect the AC power cord (mains lead).

1 Press the MENU button on the remote control to display the amplifier menu window on the display of the

system. 2 Press the t, 4, (select) button repeatedly to select the desired setting, then press the ENTER button. 3 To close the amplifier menu window, press the MENU button again.

Menu Function Default

LEVEL DRC You can enjoy Dolby Digital sound at low sound volumes• (ON/

TONE BASS Low sound is emphasized• The setting can be changed from -6 to

AUDIO SYNC You can adjust the sound when the image and the sound are not

(Dynamic range control) AUTO/OFF)

ON: Compresses sound in accordance with the compression AUTO

information contained in the content•

AUTO: Automatically compresses sound encoded in Dolby TrueHD. OFF: Sound is not compressed•

+6 in units of 1. 0

TREBLE High sound is emphasized• The setting can be changed from -6 to

+6 in units of 1. 0

(AV sync) in sync. (ON/OFF) OFF DUAL You can enjoy multiplex broadcast sound of Dolby Digital audio•

(Dual mono) (M/S (main and sub channels)/MAIN (main channel)/SUB (sub MAIN

AAV Reduces the volume discrepancies between different programs or OFF

(Advanced auto volume) between programs and commercials• (ON/OFF) EFFECT ON: The sound of the selected sound field is played• It is

(Sound effect) recommended to use this setting•

channel))

OFF: The input source is down-mixed for 2 channels• Note: When "EFFECT (Sound effect)" is set to "OFF," "EFFECT (Sound ON

effect)" is automatically set to "ON" when you change the SOUND FIELD setting•

10us

_PUl \

lurUNG/

OUNO

IELD

OICE /

/ J%

_lem

REYU_N

VOL

I' 4, (select)

ENTER RETURN

Menu Function Default HDMI ON

CTRL (Control for HDMI)

P. THRU (Pass through)

ARC To listen to digital sound from a TV compatible with the Audio (Audio return channel) Return Channel ARC technology that is connected using a High

To switch the Control for HDMI function on or off. ON/OFF

Refer to "Using the Control for HDMI function" page 6 for details.

To set the power saving mode of the pass-through function for

HDMI signals. (AUTO/ON)

AUTO: Outputs signals from the HDMI OUT jack of the system in

standby mode according to the status of the TV. This setting saves power in standby mode compared with the "ON" setting.

ON: Always outputs signals from the HDMI OUT jack in standby

mode. If any TV other than "BRAVlA" is connected, use the

system with the "ON" setting.

Note: This item appears only when "CTRL (Control for HDMI)" is set

to "ON."

Speed HDMI cable. ON/OFF ON

Note: This item appears only when "CTRL (Control for HDMI)" is set

to "ON."

AUTO

SET BT BT PWR To switch the BLUETOOTH function of this system on and off. (ON/

(BLUETOOTH power) OFF) ON

BT.STBY When the system has pairing information, the system is in the (BLUETOOTH standby) BLUETOOTH standby mode even when it is turned off. (ON/OFF) ON

AAC To set whether or not the system will use AAC via BLUETOOTH. (Advanced audio (ON/OFF) coding) Note: If you change the setting when the system is connected with ON

Note: If you change the setting to "OFF," the BLUETOOTH function

and the NFC function become disabled•

a BLUETOOTH device, the system will be disconnected from

the device•

SYSTEM A. STBY To switch the AUTO POWER OFFfunction on or off. (ON/OFF)

(Auto standby) The system turns off automatically when no operation has been ON

made within a certain period (about 20 minutes) and the system is not receiving an input signal.

VER To display the current firmware version. (Version)

SYS.RST To reset menus and settings (sound fields, etc.) of the system to (System cold reset) the initial status when it does not work properly.

Refer to "Troubleshooting" (page 18) for details.

11us

Precautions

On safety

• Should any solid object or liquid fall into the system, unplug the system and have it checked by qualified personnel before operating it any

further.

• Do not climb on the system, as you may fall down and injure yourself, or system damage may result.

• Do not place anything other than a TV on the system.

On power sources

• Before operating the system, check that the operating voltage is identical to your local power supply. The operating voltage is indicated on the nameplate at the rear of the system.

• If you are not going to use the system for a long time, be sure to disconnect the system from the wall outlet (mains). To disconnect the AC power cord (mains lead), grasp the plug itself; never pull the cord.

• One blade of the plug is wider than the other for the purpose of safety and will fit into the wall outlet (mains) only one way. If you are unable to insert the plug fully into the outlet, contact your dealer.

• AC power cord (mains lead) must be changed only at a qualified service shop.

On heat buildup

Although the system heats up during operation, this is not a malfunction.

If you continuously use this system at high volume, the system temperature atthe back and bottom rises considerably. To avoid burning yourself, do not touch the system.

On placement

• Leave the front of the system open.

• Do not place the system on top of a device that radiates heat.

• Place the system in a location with adequate ventilation to prevent heat buildup and prolong the life of the system.

• Do not place the system near heat sources or in a place subject to direct sunlight, excessive dust, or mechanical shock.

• Do not place anything at the rear of the system that might block the ventilation holes and cause malfunctions.

• If the system is being used in combination with a TV, VCR, or tape deck, noise may result and picture quality may suffer. In such a case, place the

system away from the TV, VCR, or tape deck.

• Use caution when placing the system on a surface that has been specially treated (with wax, oil, polish, etc.), as staining or discoloration

of the surface may result.

• Take care to avoid any possible injury from the corners of the system.

• Install the system so as not to harm the speaker on the bottom of this system.

• The speakers of this system are not of magnetically shielded type. Do not place magnetic cards or a CRT-type TV set on top of the system

or near it.

Notes on the glass

• Do not set something hot on the top such as a heated pan or pot. The glass top may be broken, cause injury, or be a cause of damage to this

system.

• Do not impart a strong impact to the glass top. The glass top of this system is made of hardened glass; however, there is no guarantee it

cannot be shattered. Heed the following so as not to break the glass:

- Do not impart a strong impact to the glass top by hitting it or by

dropping something pointed.

- Do not scratch the glass with something pointed or poke it.

- Do not hit the side of the glass when installing in a storage rack.

• If the glass is broken, do not touch it with bare hands. It may cause cuts.

• Do not place anything on this system that weighs over 30 kg (66 Ib 21/4 oz). Such an item can damage the glass top or this system.

oA tempered glass is stouter than ordinary glass but will shatter if broken.

12us

• A tempered glass can shatter spontaneously in extremely rare instances.

The glass used in this system has been carefully selected: however, there is no guarantee it cannot be shattered.

On operation

Before connecting other equipment, be sure to turn off and unplug the system.

On cleaning Clean the system with a soft, dry cloth. Do not use any type of abrasive

pad, scouring powder, or solvent such as alcohol or benzine.

If you have any question or problem concerning your system, please consult your nearest Sony dealer.

This system incorporates Dolby* Digital and the DTS** Digital Surround System. * Manufactured under license from Dolby Laboratories.

Dolby, and the double-D symbol are trademarks of Dolby Laboratories.

** Manufactured under license under U.S. Patent Nos: 5,956,674;

5,974,380; 6,226,616; 6,487,535; 7,212,872; 7,333,929; 7,392,195; 7,272,567 & other U.S. and worldwide patents issued & pending.

DTS-HD, the Symbol, & DTS-HD and the Symbol together are registered trademarks of DTS, Inc.

The BLUETOOTH" word mark and Iogos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Sony Corporation is under license.

This system incorporates High-Definition Multimedia Interface (HDMF M) technology.

The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing

LLC in the United States and other countries.

"BRAVIA" logo is a trademark of Sony Corporation.

"DSEE" is a trademark of Sony Corporation.

"x.v.Color" and "x.v.Color" logo are trademarks of Sony Corporation.

"PlayStation,,." is a registered trademark of Sony Computer Entertainment Inc.

The N Mark is a trademark or registered trademark of NFC Forum, Inc. in the United States and in other countries.

Android and Google Play are trademarks of Google Inc.

"ClearAudio+" is a trademark of Sony Corporation.

-I

continued

13us

Apple, the Apple logo, iPhone, iPod, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a

service mark of Apple Inc.

"Made for iPod," and "Made for iPhone" mean that an electronic accessory has been designed to connect specifically to iPod or iPhone, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod or iPhone may affect wireless performance.

Made for iPod/iPhone models

The compatible iPod/iPhone models are as follows. Update your iPod/

iPhone with the latest software before using with the system.

BLUETOOTH technology works with: oiPhone

iPhone 5s/iPhone 5c/iPhone 5/iPhone 4s/iPhone 4/iPhone 3GS

oiPod touch

iPod touch (5th generation)/iPod touch (4th generation)

Other trademarks and trade names are those of their respective owners.

14us

BLUETOOTHwireless technology

Supported BLUETOOTH version and profiles

Profile refers to a standard set of functions for various BLUETOOTH product features, Refer to "Specifications" (page 21) for the BLUETOOTH version and profiles supported by this system,

• To use the BLUETOOTH function, the BLUETOOTH device to be

connected must support the same profile as this system. Even if the device supports the same profile, the functions may differ because of the specifications of the BLUETOOTH device.

• Audio playback on this system may be delayed from that on the BLUETOOTH device because of the characteristics of the BLUETOOTH

wireless technology.

Effective communication range

BLUETOOTH devices should be used within approximatelylO meters (33 feet) (unobstructed distance) of each other. The effective

communication range may become shorter under the following conditions;

• When a person, metal object, wall or other obstruction is between

devices with a BLUETOOTH connection

• Locations where a wireless LAN is installed

• Around microwave ovens that are in use

• Locations where other electromagnetic waves are generated

Effects of other devices

BLUETOOTH devices and wireless LAN (IEEE802.11b/g) equipment use the same frequency band (2.4 GHz). When using your BLUETOOTH device near a device with wireless LAN capability, electromagnetic

interference may occur. This could result in lower data-transfer rates, noise, or inability to

connect. If this happens, try the following remedies:

• Connect this system and BLUETOOTH mobile phone or BLUETOOTH

device when you are at least 10 meters (33 feet) away from the wireless LAN equipment.

• Turn off the power to the wireless LAN equipment when using your BLUETOOTH device within 10 meters (33 feet).

Effects on other devices

The radio waves broadcast by this system may interfere with the operation of some medical devices. Since this interference may

result in malfunction, always turn off the power to this system, BLUETOOTH mobile phone and BLUETOOTH device in the following

locations:

• In hospitals, on trains or airplanes, at gas stations, and any place

where flammable gasses may be present

• Near automatic doors or fire alarms

• This system supports security functions that comply with the

BLUETOOTH specification as a means of ensuring security during communication using BLUETOOTH technology. However, this security may be insufficient, depending on the settings and other factors. So always be careful when performing communication using BLUETOOTH technology.

• Sony shall not be held liable in any way for damages or other loss

resulting from information leaks during communication using BLUETOOTH technology.

• BLUETOOTH communication is not necessarily guaranteed with all

BLUETOOTH devices that have the same profile as this system.

• BLUETOOTH devices connected with this system must comply with the

BLUETOOTH specification prescribed by the Bluetooth SIG, Inc., and must be certified to comply. However, even when a device complies with the BLUETOOTH specification, there may be cases where the characteristics or specifications of the BLUETOOTH device make it impossible to connect or may result in different control methods, display, or operation.

• Noise may occur or the audio may cut off, depending on the

BLUETOOTH device connected with this system, the communications environment, or surrounding conditions.

15us

Troubleshooting

If you experience any of the following difficulties while using the system, use this troubleshooting guide to help remedy the problem

before requesting repairs. Should any problem persist, consult your nearest Sony dealer.

POWER The system does not power up.

-) Check that the AC power cord (mains lead) is connected securely. The system is turned off automatically.

-) The "A. STBY" function is working. Set "A. STBY (Auto standby)" to "OFF" (page 11).

SOUND

No TV sound is output from the system. ") Repeatedly press the INPUT button on the remote control to

display "TV" in the display (refer to "Listening to the audio of the TV" in the supplied Startup Guide).

") Check the connection of the HDMI cable, optical digital cable, or

audio cable that is connected to the system and the TV(refer to "Connection" in the supplied Startup Guide).

") Check the sound output of the TV. Refer to the operating

instructions of the TV for the TV settings. ") Increase the volume on the TV or cancel muting. ") When a TV compatible with the Audio Return Channel (ARC)

technology is connected with an HDMI cable, make sure the cable

is connected to the HDMI input (ARC) terminal of the TV (refer to

"Connection" in the supplied Startup Guide).

") If the TV is not compatible with the Audio Return Channel (ARC)

technology, connect the optical digital cable in addition to the

HDMI cable in order to output sound (refer to "Connection" in the

supplied Startup Guide).

The sound is output from both the system and the TV. ") Turn off the sound of the system or the TV.

The TV sound from this system lags behind the image.

-) Set "SYNC (AV sync)" to "OFF" if it is set to "ON" (page 10). No sound or only a very low-level sound of the equipment

connected to this system is heard from this system.

") Press the VOL + button on the remote control and check the

volume level (refer to "Parts and controls" (page 20)).

") Press the MUTING or VOL + button on the remote control to cancel

the muting function (refer to "Parts and controls" (page 20)).

") Make sure the input source is selected correctly. You should try

other input sources by pressing the INPUT button on the remote control several times (refer to "Listening to the sound" in the supplied Startup Guide).

") Check that all the cables and cords of the system and the

connected equipment are firmly inserted.

Bass sound is not heard or its volume is low.

") Press the SWVOL + button on the remote control to increase the

subwoofer volume (refer to "Parts and controls" (page 20)). The surround effect cannot be obtained. ") Depending on the input signal and the sound field setting,

surround sound processing may not work effectively. The

surround effect may be subtle, depending on the program or disc. ") To play multi channel audio, check the digital audio output setting

on the device connected to the system. For details, refer to the

operating instructions supplied with the connected equipment.

16us

BLUETOOTH

BLUETOOTH connection cannot be completed. ") Make sure that the illumination LED (blue) is lit (refer to "Listening

to the sound from BLUETOOTH devices" in the supplied Startup

Guide). System status illumination LEDstatus

During BLUETOOTHpairing Flashesquickly in blue

The system is attempting to connect Flashesin blue

with a BLUETOOTHdevice

The system has established Lit in blue

connection with a BLUETOOTHdevice

The system isin BLUETOOTHstandby Unlit

mode (when the system isoff)

") Make sure the BLUETOOTH device to be connected is turned on

and the BLUETOOTH function is enabled.

") Bring this system and the BLUETOOTH device closer together. ") Pair this system and the BLUETOOTH device again. You may need

to cancel the pairing with this system using your BLUETOOTH

device first.

Pairing cannot be achieved. ") Bring this system and the BLUETOOTH device closer together

(refer to "Listening to the sound from BLUETOOTH devices" in the

supplied Startup Guide).

") Make sure this system is not receiving interference from a wireless

LAN equipment, other 2.4 GHz wireless devices, or a microwave oven. If a device that generates electromagnetic radiation is

nearby, move the device away from this system.

No sound is output from the connected BLUETOOTH device. ") Make sure that the illumination LED (blue) is lit (refer to "Listening

to the sound from BLUETOOTH devices" in the supplied Startup

Guide).

") Bring this system and the BLUETOOTH device closer together. ") If a device that generates electromagnetic radiation, such as a

wireless LAN equipment, other BLUETOOTH devices, or a

microwave oven is nearby, move the device away from this system.

") Remove any obstacle between this system and the BLUETOOTH

device or move this system away from the obstacle. ") Reposition the connected BLUETOOTH device. ") Try changing the wireless frequency of the Wi-Fi router, computer,

etc. to the 5 GHz band. ") Increase the volume on the connected BLUETOOTH device.

The sound is not in sync with the image. ") When you are watching movies, you may hear the sound with a

slight delay from the image.

REMOTE CONTROL

The remote control does not function.

") Point the remote control at the remote control sensor on the

system (refer to "Parts and controls" (page 19)). ") Remove any obstacles in the path between the remote control

and the system. ") Replace both batteries in the remote control with new ones, if they

are weak. ") Make sure you are pressing the correct button on the remote

control.

tl)

continued

17us

OTHERS S

The Control for HDMI function does not work properly. ") Check the HDMI connection (refer to "Connection" in the supplied

Startup Guide).

") Set up the Control for HDMI function on the TV. Refer to the

operating instructions supplied with the TV for TV setting.

") Make sure that any equipment connected is compatible with

"BRAVIA" Sync.

") Check the Control for HDMI settings on the connected equipment.

Refer to the operating instructions supplied with the connected

equipment.

÷ If you connect/disconnect the AC power cord (mains lead), wait

more than 15 seconds before operating the system.

÷ If you connect the audio output of video equipment with the

system, using a cable otherthan an HDMI cable, no sound may be output because of "BRAVlA" Sync. In such a case, set "CTRL (Control for HDMI)" to "OFF" (page 11)or connect the cable from the audio output jack of the video equipment directly to the TV.

"PRTECT (protect)" appears on the display of the system. ÷ Touch the I/_ (on/standby) touch key on the main unit to turn off

the system. After the indication disappears, disconnect the AC

power cord (mains lead) then check that nothing is blocking the

ventilation holes of the system.

RESET

If the system still does not operate properly, reset the system as follows:

Press the I/_ (on/standby) button on the remote control to turn the system on.

Press the MENU button on the remote control.

Press the 4, 4, (select) button repeatedly until "SYSTEM" appears, then press the ENTER button.

Press the 4, 4, (select) button repeatedly until "SYS.RST" appears, then press the ENTER button (page 11).

Press the ENTER button after displaying "START."

"RESET" appears on the display, and the settings of the menu and sound fields, etc. return to their initial statuses.

Disconnect the AC power cord (mains lead).

18us

Parts and controls

Front/Top

[_ I/_ (on/standby) touch key [_ PAIRING touch key

[_ INPUTtouch key [_ Remote control sensor

[_ Illumination LED

• White: When the display brightness is set to "Off," the illumination LED turns off.

• Blue: BLUETOOTH mode (page 17)

[_ Display [_ N mark

To use an NFC function, touch your NFC device to the mark.

Back

[_ AC power cord (mains lead) [_ DIGITAL IN (OPT (TV))jack

[_ ANALOG IN jack [_ HDMI IN 1/2/3jacks [_ HDMI OUT (TV (ARC)) jack

* Touch a touch key lightly with a fingertip. If you touch two or more

keys simultaneously or touch with a thumb, appropriate operation may not be obtained.

continued

19us

ii[ilIiilill llllllllllllllllllllllllllllllllllllllllllllllllllllllllllllll l

[_ I/_ (on/standby) button [_ INPUT button

[_ MUTING button [_ VOL (volume) +/- button [_ SOUND FIELD button*

[_ VOICE button* [_ DISPLAY button

[_ NIGHT (night mode) button* [_ SW VOL (subwoofer volume) +/- buttons

[_ MENU/4` 4,(select)/ENTER/RETURN buttons

* Refer to "Enjoying the sound effects" in the supplied Startup Guide.

The display brightness can be switched. Bright --_ Dark --_ Off

• When the display brightness is set to "Off," the display is

turned off after the display shows operation status for several

seconds.

• When the setting is changed to "Bright" from "Off," the display

shows the audio stream information.

Adjusts the volume of the bass sound.

Select the desired setting by pressing the 4, 4, (select) button then register it by pressing the ENTERbutton.

20us

Specifications

Amplifier section

U.S. models: POWER OUTPUT AND TOTAL HARMONIC DISTORTION:

(FTC) Front L + Front R:

With 3 ohms loads, both channels driven, from 400 - 20,000 Hz; rated 20 Watts per channel minimum RMS power, with no more than 1% total harmonic distortion from 250 milliwatts to rated output.

POWER OUTPUT (reference)

Front L/Front R speaker: 35 Watts (per channel at 3 ohms, 1 kHz)

Subwoofer: 100 Watts (at 4 ohms, 1OO Hz)

Canadian models: POWER OUTPUT (rated)

Front L+ Front R: 20 W + 20 W

(at 3 ohms, 1 kHz, 1% THD)

POWER OUTPUT (reference)

Front L/Front R speaker: 35 Watts (per channel at 3 ohms, 1 kHz)

Subwoofer: 100 Watts (at 4 ohms, 1OO Hz)

Inputs

HDMI IN 1/2/3"

ANALOG IN

DIGITAL IN (OPT (TV))

* These 3jacks are identical. Using any of them makes no difference. Output

HDMI OUT (TV (ARC))

BLUETOOTH section

Communication system

BLUETOOTH Specification version 3.0

Output

BLUETOOTH Specification Power Class 2

Maximum communication range

Line of sight approx. 10 m (33 ft) 1)

Maximum number of devices to be registered

9 devices

Frequency band

2.4 GHz band (2.4000 GHz - 2.4835 GHz)

Modulation method

FHSS (Freq Hopping Spread Spectrum)

Compatible BLUETOOTH profiles 2)

A2DP (Advanced Audio Distribution Profile) AVRCP 1.3 (Audio Video Remote Control Profile)

Supported Codecs 3)

SBC4), AAC s)

Transmission range (A2DP)

20 Hz - 20,000 Hz (Sampling frequency 44.1 kHz)

1) The actual range will vary depending on factors such as obstacles between devices, magnetic fields around a microwave oven, static electricity, cordless phone, reception sensitivity, operating system, software application, etc.

2) BLUETOOTH standard profiles indicate the purpose of BLUETOOTH communication between devices.

3) Codec: Audio signal compression and conversion format

4) Subband Codec

5) Advanced Audio Coding

Front L/Front R speaker section Speaker system

Full range speaker system, Acoustic suspension

Speaker

35 mm (17/16 in) x 80 mm (3 1/4 in) cone type

Rated impedance

3 ohms

continued

21us

+ 47 hidden pages