Page 1
HD DIGITAL VIDEO DISTRIBUTION BOARD
HKPF-103M
INSTALLATION MANUAL
1st Edition (Revised 2)
Page 2
! WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so. Refer all servicing to
qualified service personnel.
! WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die
Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.
! A VERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin
de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les
réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.
Pour toute réparation faire appel à une personne compétente uniquement.
HKPF-103M (UCJ) Serial No. 10101 through 10315
HKPF-103M (SY) Serial No. 10316 through 10954
HKPF-103M/1 (SY) Serial No. 11001 and Higher
HKPF-103M IM
Page 3
Table of Contents
Manual Structure
Purpose of this manual ........................................................................................ 3 (E)
Contents ............................................................................................................... 3 (E)
Related manuals................................................................................................... 3 (E)
1. Supplied Accessories ................................................................ 1-1 (E)
2. Board Attachment ......................................................................... 1-1 (E)
3. Name and Function of Connectors .................................... 1-4 (E)
3-1. Name and Function of Connectors........................................................1-4 (E)
3-2. Connectors and Cables for Connection.................................................1-5 (E)
4. Name and Function of Switches and LEDs .................. 1-6 (E)
4-1. Name and Function of Switches and LEDs (On The Front Panel) .......1-6 (E)
4-2. Name and Function of Switches and LEDs (On Board) .......................1-7 (E)
HKPF-103M IM
1 (E)
Page 4
Page 5
Purpose of this manual
Contents
Manual Structure
This manual is the installation manual of HD DIGITAL VIDEO DISTRIBUTION
BOARD HKPF-103M.
This manual is intended for use by trained service engineers, and is provided the
information required for the installation.
1. Supplied Accessories
This section describes the supplied accessories.
2. Board Attachment
This section describes the methods for board attachment and the careful points.
3. Name and Function of Connectors
This section describes the name and functions of connectors.
4. Name and Function of Switches and LEDs
This section describes the name and functions of the front panel, the switches and
the LEDs.
Related manuals
The following manuals are prepared for HKPF-103M.
..
. Operation Manual (Supplied with HKPF-103M)
..
Part number : 3-203-157-XX
This manual describes the notes on the operating, and the locations and the
functions.
..
. Maintenance Manual (Available on your request)
..
Part number : 9-968-554-XX
This manual describes the information required for the maintenance information and
the information that premise the service based the component parts.
If this manual is required, please contact your local Sony Sales Office/Service
Center.
HKPF-103M IM
3 (E)
Page 6
Page 7
1. Supplied Accessories
2. Board Attachment
1. Supplied Accessories
The supplied accessories of HKPF-103M are as follows.
. Label : 1
. Operation manual : 1
. Installaition manual : 1
2. Board Attachment
. This section is described how to attach the board in PFV-
HD300. For how to attach it in models other than PFVHD300, refer to the manual supplied for each model.
. Insert the board in any blank slot of PFV-HD300.
Attach any board to the 14th slot, if the status out
function is used however.
Front panel
1. Loosen the four screws (with stopper) and detach the
front panel.
2. Unscrew the six screws and detach the board supports.
3. Insert the board along the board guide rail.
Board guide rail
Board
Put the component side so
that it is viewed from the right side.
4. Insert the board in the slot as far as it will go and close
the two board levers in the directions of arrows 1.
PSW3 x 6
PSW3 x 6
Board supports
1
2
2
1
1
Board lever
1
2
Board lever
2
1Attachment
2Detachment
5. Put the supplied label onto the board lever.
6. Attach the board supports.
7. Attach the front panel.
n
When detaching the board, pull out the board toward you while
pushing the two board levers in the directions of arrows 2.
HKPF-103M IM
1-1 (E)
Page 8
2. Board Attachment
Rear panel
m
1. Save the detached blank panel for later use.
2. Be sure to attach the IFB shield and their parts attached to both sides of the blank panel, since they are
the parts that use spurious emission.
3. In order to maintain the cooling effect for
PFV-HD300, do not leave the slot open. Be sure to
attach the blank panel to an empty slot.
The connector panel attachment methods are divided into
three types depending on the slot number.
<Type 1> For slot No. 1
<Type 2> For slot Nos. 2 to 6, 9 to 14
<Type 3> For slot Nos. 7 and 8
The attachment methods for each type are explained
below.
<Type 1>
1. Remove the five screws, and remove the IFB shield L,
IFB shield and blank panel.
Blank panel
IFB shield
PWH3 x 6
PWH3 x 6
x 6
PWH3
IFB shield L
2. Insert the connector panel.
3. Fasten the IFB shield L, IFB shield and connector
panel to the unit using the five screws that are removed
in the step 1.
Connector panel
IFB shield
PWH3 x 6
PWH3 x 6
PWH3 x 6
IFB shield L
1-2 (E)
HKPF-103M IM
Page 9
2. Board Attachment
<Type 2>
1. Remove the four screws, and remove the two IFB
shields and blank panel.
Blank panel
PWH3 x 6
IFB shield
IFB shield
PWH3 x 6
<Type 3>
1. Remove the five screws, and remove the IFB shield,
rear shield retainer (center) assembly and blank panel.
Rear shield retainer
(center) assembly
B3 x 6
PWH3 x 6
PWH3 x 6
Blank panel
IFB shield
2. Insert the connector panel.
3. Fasten the two IFB shields and connector panel to the
unit using the four screws that are removed in the step
1.
Connector panel
PWH3 x 6
IFB shield
IFB shield
PWH3 x 6
2. Insert the connector panel.
3. Fasten the IFB shield, rear shield retainer (center)
assembly and connector panel to the unit using the five
screws that are removed in the step 1.
Rear shield retainer
(center) assembly
B3 x 6
*
PWH3 x 6
PWH3 x 6
Connector panel
IFB shield
HKPF-103M IM
* Do not remove a center screw on the rear shield retainer
(center) assembly.
1-3 (E)
Page 10
3. Name and Function of Connectors
3. Name and Function of Connectors
3-1. Name and Function of Connectors
HD-VDA
DIGITAL IN
1
DIGITAL OUT
1
2
2
3
4
5
6
HKPF-103M
1 DIGITAL VIDEO IN connector (BNC type)
This connector is received an HD SDI (conforming to the SMPTE 291M/292M/299M standard)
signal.
2 DIGITAL VIDEO OUT connectors (BNC type)
These connectors are provided an HD SDI (conforming to the SMPTE 291M/292M/299M standard)
signal.
1-4 (E)
HKPF-103M IM
Page 11
3-2. Connectors and Cables for Connection
Use the connector and the cable below or the equivalent at the tip when cables are
connected to each connector on the connector panel, during connection and service.
Connector on HKPF-103M side Adaptive connector/cable
Panel display Name Name Sony part No.
DIGITAL IN BNC (75 Z) BNC (75 Z) 1-560-069-11
5C-FB coaxial cable —
DIGITAL OUT from 1 to 6 BNC (75 Z) BNC (75 Z) 1-560-069-11
5C-FB coaxial cable —
3. Name and Function of Connectors
HKPF-103M IM
1-5 (E)
Page 12
4. Name and Function of Switches and LEDs
4. Name and Function of Switches and LEDs
4-1. Name and Function of Switches and LEDs (On The Front Panel)
POWER
FORMAT
VIDEO
1080
CRCC
1
2
FORMAT SEL
1
2
3
4
5
6
7
8
SELECT SW
1 Indication lamps : D900, D700, D701, D706
2 Format display LED
3
4
3 Format selection switch : S702
4 Selection switch : S703
1-6 (E)
HKPF-103M IM
Page 13
4-2. Name and Function of Switches and LEDs (On Board)
1. DPR-151 Board
4. Name and Function of Switches and LEDs
S600
D900
D700
D701
D706
LED
S702
1
S703
8
S706
S707
S708
S601
S300
DPR-151D Board (S/N: 11001 and higher)
D900 (green) : +5 V/_5 V power indication lamp
Lights : Nomal
Lights off : Abnomal
D700 (green) : VIDEO EXIST (input indication) lamp
Lights : Input signal
Lights off : No input signal
CN1CN2
S600
D900
D700
D701
D706
LED
S702
1
S703
8
S704
S705
S706
S601
S300
DPR-151C Board (S/N: 10101 through 10954)
CN101CN102
S703-2 : Test mode switch
This switch is changed the setting during self-diagnosis for
the board operation.To enter the test mode,select this switch
to the upper (ON) position and turn ON the power switch.
Upper : ON
Lower : OFF
Factory setting : OFF
D701 (green) : ACTIVE LINE indication lamp
Lights : 1080 lines
Lights off : 720,1035 lines
D706 (red) : CRCC error indication lamp
Lights : Error
Lights off : No error
S703-1 : Software version display switch
If the S703-2 switch is selected to the test mode and turn
ON the power switch, the software version is displayed on
the LED.
Upper : Version display
Lower : OFF
Factory setting : OFF
n
When switch S703-2 is selected to OFF,this switch is not
operated even if its setting is changed.
The LED display is indicated with a decimal point omission, for example, Version 1.2 is “12”.
S703-3 : Format selection switch
This switch is selected the format.
Upper : MANUAL
Lower : AUTO
Factory setting : AUTO
S703-4 to 8 : Not in use
S600 : CPU resetting switch
This switch is initialized CPU. It is not usually used.
S601 : CPU program re-writing switch
USE : Usually use position
INIT : CPU program re-writing only
Factory setting : USE
S300 : VCO free-run adjustment switch
USE : Usually use position
FTEST : Free-run adjusting only
Factory setting : USE
HKPF-103M IM
1-7 (E)
Page 14
4. Name and Function of Switches and LEDs
Serial No. 11001 and higher
S706 : Status output selection switches
These switches select an error information as status output.
S706-1 S706-2 S706-3 S706-4 S706-5 S706-6 S706-7 S706-8 Remarks
No SDI Format Frequency Video signal — — Internal — Factory setting
input error error error set up error = ON
n
The board of the HKPF series need to be attached in the 4th slot of PFV-HD50A or the 14th slot of PFV-HD300, to do the
status out function effectively.
Serial No. 10101 through 10954
S704, S705 : Format selective range setting switch
If the S703-3 switch is the lower side : AUTO, an automatic selectable format is set for each bit.
ON : That bit format is possible to automatic-select
OFF : That bit format is impossible to select
Factory setting : All of the selectable bits are ON
n
If a lot of selectable format is specified, the time required till lock becomes long on the format switch point.
We recommend setting the bit switches, that correspond to a format usually not in use, to OFF position.
When operating at mono-format, the S703-3 switch is set the upper (manual) position and select the format of your purpose
with the S702 switch. (Refer to the format selection table, next page)
S706-1, S706-2 : Status output selection switches
These switches select an error information as status output.
Switch position Item Remarks
S706-2 S706-1 Internal SDI not Format SDI CRCC
set up error detected error error
0 (Lower) 0 (Lower) OOOOFactory setting
0 (Lower) 1 (Upper) OXOO
1 (Upper) 0 (Lower) OXXX
1 (Upperr) 1 (Upper) XXXX
O : Output, controlled
X : Output, non-control
n
The board of the HKPF series need to be attached in the 4th slot of PFV-HD50A or the 14th slot of PFV-HD300, to do the
status out function effectively.
1-8 (E)
HKPF-103M IM
Page 15
Format selection table
Format selection : S703-3
4. Name and Function of Switches and LEDs
1 (Upper)
manual
S702
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
__
Manual
Manual
0 (Lower)
automatic
(Factory setting)
S704, S705
S705-1
S705-2
S705-3
S705-4
S705-5
S705-6
S705-7
S705-8
S704-1
S704-2
S704-3
S704-4
S704-5
S704-6
S704-7
S704-8
Automatic
__
__
Line/Field
Frequency
1035/60i
1035/59.94i
1080/60i
1080/30PsF
1080/59.94i
1080/29.97PsF
1080/50i
1080/25PsF
1080/24PsF
1080/23.976PsF
1080/30P
1080/29.97P
1080/25P
1080/24P
1080/23.976P
720/60P
720/59.94P
Un-definition
Un-definition
Display without the above
Under search
Format mismatch
Format
non-correspondence
Scanning
system
Interlace
system
/
Frame
segment
Progressive
LED display,
(1080)
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
Blinking
Blinking
OFF
LED display,
(
Format
)
60
d
59
d
60
d
30
59
d
29
50
d
25
24
23
d
30
d
29
d
25
d
24
d
23
d
60
d
59
__
__
__
Blinking
Blinking of
number
__
Remarks
Discrimination by the ID
Discrimination by the ID
Discrimination by the ID
Non-correspondence
Non-correspondence
Non-correspondence
Non-correspondence
Non-correspondence
(
*1)
Blinking of specified
number
(*1) : n At the units from serial No.10101 to 10315, softwares are required updating to version 1.1.
[Format display]
The format is displayed with number of two digits on the seven segments LED.
(The seven segments LED located as below).
HKPF-103M IM
1-9 (E)
Page 16
Page 17
The material contained in this manual consists of
information that is the property of Sony Corporation.
Sony Corporation expressly prohibits the duplication of
any portion of this manual or the use thereof for any
purpose other than the operation or maintenance of the
equipment described in this manual without the express
written permission of Sony Corporation.
Le matériel contenu dans ce manuel consiste en
informations qui sont la propriété de Sony Corporation.
Sony Corporation interdit formellement la copie de
quelque partie que ce soit de ce manuel ou son emploi
pour tout autre but que des opérations ou entretiens de
l’équipement à moins d’une permission écrite de Sony
Corporation.
Das in dieser Anleitung enthaltene Material besteht aus
Informationen, die Eigentum der Sony Corporation sind.
Die Sony Corporation untersagt ausdrücklich die
Vervielfältigung jeglicher Teile dieser Anleitung oder den
Gebrauch derselben für irgendeinen anderen Zweck als
die Bedienung oder Wartung der in dieser Anleitung
beschriebenen Ausrüstung ohne ausdrückliche
schriftliche Erlaubnis der Sony Corporation.
HKPF-103M IM
Page 18
HKPF-103M (SY) J, E
3-203-437-03 (1)
Printed in Japan
Sony Corporation 2002. 1 22
B&P Company ©1999
Loading...