SONY DSC-T100-3 Service Manual

SERVICE MANUAL

Ver. 1.1 2007.04

SUPPLEMENT-1

DSC-T100

Auto-ADJ

File this supplement with the service manual.

• Change of Automatic Adjustment Program

• Change of Message for Destination Data Write

•Addition of [Read], [Save], and [Load] buttons to Angular
Velocity Sensitivity Adjustment

•Addition of AF Illuminator as a Controllable LED to
LED Check

(DI07-003)

DSC-T100_ADJ

9-852-191-81

Sony EMCS Co.

2007D0500-1

© 2007.4

Published by Kohda TEC

• Change of Automatic Adjustment Program

Version of Automatic Adjustment Program has
been changed from Ver_1.0r01 into Ver_1.1r02.

: Points changed portion.

6-1. CAMERA SECTION ADJUSTMENTS

1-2. ADJUSTMENT PROGRAM

2. Start of Automatic Adjustment Program
(Service manual page 6-13)

Double-click the application file (DSC-T100 Auto-Adj
V er_1.1r02.ex e), and the Automa tic Adjustment Program will start.

3. Function of Each Button on Main Menu Screen
(Service manual page 6-13)

When the Automatic Adjustment Program started, the Main Menu
screen in Fig. 6-1-14 will appear. On this screen, select each ad­justment section.

• Change of Message for Destination Data
Write

: Points changed portion.

1-3. DESTINATION DATA WRITE

2. Destination Data Write

(Service manual page 6-15)

[Writing method]

1) Select the written destination with the Destination List.

1

qa

4

5

6

7

8

2

9

0

3

Fig. 6-1-14

qa This part indicates the version of Automatic Adjustment Pro-

gram.

2) Click the [Data Write] button.

3) The writing finishes when the following message is displayed.

DSC-T100_ADJ

— 2 —

• Addition of [Read], [Save], and [Load] buttons
to Angular Velocity Sensitivity Adjustment

& : Points added portion.

9. CAMERA Adjustment 7

Perform this adjustment only when replacing the angular velocity
sensor or lens block. When the microprocessor, circuit etc. is dam­aged, don't perform this adjustment but check the operations only.

9-1. Precaution before adjustment
(Service manual page 6-29)

Before adjustment, read the following data and record them.
When the SY-171 board is replaced, read out the data before the
replacement, and record them.

Reading out method:

1) Read out the data in Block:11, Page:61, Address:0E10, and

name this as Dp.

2) Read out the data in Block:11, Page:61, Address:0E11, and

name this as Dy.
Note: The previous data (Dp, Dy) can be read from the SY-

171 board and it can be saved in the PC as a file by
using the Automatic Adjustment Program. (Refer to “9-

4. Angular Velocity Sensor Sensitivity Adjustment”)

(

: Points changed portion.

9-4. Angular Velocity Sensor Sensitivity Adjustment
(Service manual page 6-30)

[Adjusting method]

1) Click the [Start] button of Camera Adjustment 7, and the fol-
lowing screen will appear.

The buttons on this screen provide the following functions.
[Read] button:Reads and displays the previous data (Dp, Dy)

from the SY-171 board.

[Save] button: Saves the previous data (Dp, Dy) in the PC as a

file.

[Load] button: Loads and displays the previous data (Dp, Dy)

from the file saved in the PC.

Note: The previous data (Dp, Dy) is sav ed with the file name

“DSC_T100_DpDyData.dat” in the same folder as the
Automatic Adjustment Program.

2) Input the previous data (Dp, Dy) into screen.
If the previous data cannot be read, give a check to the checkbox
at lower left of screen.

3) Input the sensitivity of respective sensors (S
“Preparation” into the screen.
If only either sensor was replaced, give a check to the checkbox
for the sensor not replaced at the lower left of the screen.

4) Input the PITCH/YAW data of lens (L1, L2) read at “Prepara-
tion” into the screen.
If the lens was not replaced, give a check to the checkbox at
the lower left of the screen.

5) Click the [OK] button, and the adjustment data is then calcu-
lated from the sensor sensitivity value and the calculation re­sult is written to the memory in the camera.

6) Upon successful completion of the data writing, the following
screen will appear. Check that the steady shot function oper­ates normally.

, S

) read at

501

502

DSC-T100_ADJ

— 3 —

• Addition of AF Illuminator as a Controllable
LED to LED Check

& : Points added portion.

6-2. SERVICE MODE

2-2. SERVICE MODE

3. LED Check

(Service manual page 6-37)

Click the [LED Check] b utton on the SER VICE MODE screen, and
the “LED CHECK” screen will appear.

*

Using method:

LED ON or OFF can be controlled with [LED ON] or [LED OFF]
button on the screen.

DSC-T100_ADJ

— 4 —