Before Starting Adjustments ·····················································6-1
1-1. Adjusting Items When Replacing
Main Parts and Boards ····················································6-3
1-2. List of Service Tools ························································6-4
6-1. Camera Section Adjustments···········································6-6
1-1. Preparations Before Adjustments ····································6-6
1-2. Adjustment Program······················································6-13
1-3. Destination Data Write ··················································6-15
1-4. USB Serial No. Input·····················································6-16
1-5. Video System Adjustments············································6-17
1-6. Camera System Adjustments·········································6-20
1-7. LCD System Adjustments ·············································6-31
1-8. Error···············································································6-33
6-2. Service Mode·································································6-35
2-1. Application for Adjustment (SeusEX) ··························6-35
2-2. Service Mode·································································6-36
2-3. Data Backup ··································································6-41
DSC-T100_ADJ
— 2 —
SECTION 6
ADJUSTMENTS
Before starting adjustments
Method for Copying or Erasing the Data in Internal Memory
(Internal Memory/Music)
The data can be copied/erased by the operations on the HOME screen. (When erasing the data, execute formatting the
internal memory.)
Note 1: When replacing the SY-171 board, erase the data in internal memory of the board before replacement.
Note 2: When replacing the SY-171 board, execute formatting and initialize the internal memory after replace-
ment.
Method for copying the data in internal memory
Copy
Copies all images in the internal memory to a “Memory Stick Duo”.
1 Insert a “Memory Stick Duo” having 32MB or larger capacity.
2 Select [Copy] with v/V/b/B on the control button, then press z.
The message
3 Select [OK] with v, then press z.
Copying starts.
To cancel the copying
Select [Cancel] in step 3, then press z.
• Use a fully charged battery pack. If you attempt to copy image files using a battery pack with little
remaining charge, the battery pack may run out, causing copying to fail or possibly corrupting the data.
• You cannot copy individual images.
• The original images in the internal memory are retained even after copying. To delete the contents of the
internal memory, remove the “Memory Stick Duo” after copying, then execute the [Format] command in
[ Internal Memory Tool].
• When you copy the data in the internal memory to the “Memory Stick Duo”, all the data will be copied.
You cannot choose a specific folder on the “Memory Stick Duo” as the destination for the data to be
copied.
• Even if you copy data, a DPOF (Print order) mark is not copied.
“All data in internal memory will be copied” appears.
Method for formatting the internal memory
This item does not appear when a “Memory Stick Duo” is inserted in the camera.
Format
Formats the internal memory.
• Note that formatting irrevocably erases all data in the internal memory, including even protected images.
1 Select [Format] with v/V/b/B on the control button, then press z.
The message “All data in internal memory will be erased” appears.
2 Select [OK] with v, then press z.
The format is complete.
To cancel the formatting
Select [Cancel] in step 2, then press z.
DSC-T100_ADJ
6-1
How to Write Data to Internal Memory
Usually, the camera has been set so as to disable the data writing from the PC to the internal memory of the camera.
This setting must be changed temporarily when the data is to be written to the internal memory such as a case after the
board replacement.
To change the setting, use the write enable tool “WriteEnableTool.exe”.
Data writing method
1) Connect the PC to the camera (USB mode: Mass Storage), and switch the driver to the “Sony Seus USB Driver”.
2) Start the Write Enable Tool and the SeusEX.
3) Click the [Activate Write Enable Mode] button of the Write Enable Tool.
4) Upon completion of the setting change, the following message will be displayed.
5) Return the driver to the original one, and connect the PC to the camera (USB mode: Mass Storage).
6) Write the data read out into the PC to the internal memory of the camera.
7) Disconnect the PC from the camera, and turn off the camera.
Note: By turning off the camera, the write enable setting is reset.
DSC-T100_ADJ
6-2
1-1. Adjusting items when replacing main parts and boards
When replacing main parts and boards, adjust the items indicated by z in the following table.
Note 1: The automatic Adjustment Program does not support the “Wide Limit Adjustment”. Perform it manually.
Note 2: When replacing the SY-171 board, erase the data in internal memory of the board before replacement.
Note 3: When replacing the SY-171 board, execute formatting and initialize the internal memory after replacement.
Replaced parts
BlockMounted partsBoard
replacementreplacementreplacement
Adjusting itemAdjustment
Destination Data WriteDestination data write
USB Serial No. InputUSB serial No. input
Composite video level adj.
VIDEO adjustment
CAMERA adjustment 1Hall adj.
(Note 1)Wide limit adj.
CAMERA adjustment 2Flange back adj.
CAMERA adjustment 3Flange back check
CAMERA adjustment 4
CAMERA adjustment 5Strobe adj.
CAMERA adjustment 6Auto focus illumination check
CAMERA adjustment 7Angular velocity sensor sensitivity adj.
LCD adjustment
Component out Y level adj.
Component out Pb level adj.
Component out Pr level adj.
F No. compensation
Measure gain adj.
Light value adj.
Mechanical shutter adj.
AWB 3200K-5800K standard data input
AWB 3200K-5800K check
Color reproduction adj. & check
CCD linearity check
CCD white defect compensation check
CCD black defect compensation check
V-COM adj.
White Balance adj.
LCD unit
(AF illumination LED)
(Timing gen., CCD signal process)
(Video amp.)
(PITCH, YAW sensor)
LCD901
D002
IC304
IC602
SE502, SE501
(COMPLETE)
(COMPLETE) (Note 2, 3)
Lens block
CCD block assy (Including CD-696 flexible board and CCD imager)
Flash unit
LCD block
ST-162 board
SY-171 board
SY-171 board
SY-171 board
ST-162 board
SY-171 board
z
z
zz
z
z
zz
zz
zzz
zzz
zzz
z
zzzz z
zzz
zzz
z
z
DSC-T100_ADJ
Table 6-1-1
6-3
1-2. List of service tools
• Oscilloscope• Color monitor
J-1
J-4
J-7
J-10
Personal computer
(Note 1)
USB cable
1-829-868-41
Clear chart
For PTB-450:
J-6080-621-A
For PTB-1450:
J-6082-560-A
J-2
HASP key and application
for adjustment (SeusEX)
Contact our service headquater of each area
how to get the application for adjustment
(SeusEX) and HASP key.
J-5
Pattern box PTB-450
J-6082-200-A
or
Small pattern box
PTB-1450
J-6082-557-A
J-8
Minipattern box
J-6082-353-B
J-11
J-3
USB, A/V, DC IN cable
for multi-use terminal
1-830-848-21
J-6
9 colors chart (Note 2)
For PTB-1450:
J-6082-562-A
J-9
Flange back
adjustment jig
J-6082-563-A
J-12
Siemens star chart
J-6080-875-A
Back ground paper
J-2501-130-A
AC power adaptor
AC-LS5
1-479-284-51
Fig. 6-1-1
Note 1: Personal computer
OS:Windows98/98SE/Me/2000/XP Home/XP Pro
RAM: 256 MB or more recommended
USB: 2.0 recommended (also compatible with 1.1)
Two connectors are required.
Note 2: In using the 9 colors chart on the pattern box PTB-450, adjust the chart size through the procedure shown below so that it matches
to the pattern box PTB-450.
1) Prepare a woody board A of the thickness 5 mm, and paint it mat-black.
2) Fit the 9 colors chart in the woody board A, and secure the chart with a black tape, etc. to shield the light.
woody boad A
360 mm
155 mm
135 mm
280 mm
woody boad A
DSC-T100_ADJ
9 colors chart
6-4
J-14
J-15J-13
Tripod Adaptor
J-6082-577-A
Camera table
J-6082-384-A
Fig. 6-1-2
Note 3: The HD Station must be modified. (Refer to “4. HD Station Modifying Procedure”)
HD Station (CSS-HD1)
(Note 3)
A-1242-190-A
DSC-T100_ADJ
6-5
6-1. CAMERA SECTION ADJUSTMENTS
1-1.PREPARATIONS BEFORE ADJUSTMENTS
1-1-1. Preparations
1) Connect the equipment for adjustments according to Fig. 6-1-4.
2) Start up the application for adjustment (SeusEX).
• Connecting the Equipment
PC
(The SeusEX must be installed in the PC.)
OS: Windows 98/98SE/Me/2000/XP
RAM: 256MB or more recommended
USB: 2.0 recommended (also compatible with 1.1)
Two connectors are required.
To Multi connector
HASP Key
Pattern box
L = About 11 cm
Front of the lens
L
Camera
Fig. 6-1-3
DISP SEL switch setting
TV: Video/Camera
System Adjustment
CAMERA: LCD
System Adjustment
AC power adaptor
AC-LS5
(1-479-284-51)
AC IN
To DC IN jack
Video system Adjustment
(Composite video level adj.)
Osilloscope
Terminated
75 Ω
To USB
connector
Color monitor
Video
(yellow)
Audio
(Black)
USB, A/V, DC IN cable
for multi-use terminal
(1-830-848-21)
Fig. 6-1-4
Note: The set must be connected to the modified HD station when performing the “Component out (Y, Pb, Pr) level adjustment” in the
“Video System Adjustment”.
DSC-T100_ADJ
6-6
PC
OS: Windows 98/98SE/Me/2000/XP
RAM: 256MB or more recommended
USB: 2.0 recommended
(also compatible with 1.1)
Two connectors are required.
AC IN
AC power adaptor
USB cable
(1-829-868-41)
USB connector
HASP Key
To DC IN jack
To USB
connector
To USB
connector
Terminated
75 Ω
Pr (Red)
Pb (Blue)
Y (Green)
(COMPONENT OUT)
Measurement Point (Component out (Y, Pb, Pr) level adj.)
To COMPONENT OUT
• Connection diagram when “Component out (Y, Pb, Pr) level adjustment in “Video System Adjustment” is performed.
P
r
P
b
Y
Note: For the USB connection, refer to “4. HD Station Modifying Procedure”.
Fig. 6-1-5
DSC-T100_ADJ
6-7
1-1-2. Precautions
1. Setting the Switch
Unless otherwise specified, set the switches as follows and perform adjustments.
1. HOME button (Shooting) ............................................ A uto Adjustment
2. ZOOM button............................................................... WIDE end
3. Digital Zoom
(Setting - Shooting Settings - Shooting Settings 1) .... Off
9 colors chart (Standard picture frame)
A
Green
C14Blue
Effective picture frame
Fig. a LCD screen or under scan
( )
BA
Yellow
WhiteCyan
monitor TV picture
W14
Red
Magenta
A
2
2. Subjects
1) 9 colors chart (Standard picture frame).
When performing adjustments using the 9 colors chart, adjust
the picture frame as shown in Fig. 6-1-6. (Standard picture
frame)
2) Clear chart (Standard picture frame)
Remove the 9 colors chart from the pattern box and insert a
clear chart in its place. (Do not perform zoom operations during this time)
C
B
C
A = B
C =
C14: Filter for AWB 5800K adjustment
Transparent window
Fig. 6-1-6
B
3
Adjust the camera position and direction
to obtain the LCD screen or the monitor
TV display shown in Fig. a.
DSC-T100_ADJ
6-8
3. Preparing the Flash Adjustment Box
A dark room is required to provide an accurate flash adjustment.
If it is not available, prepare the flash adjustment box as given
below;
1) Provide woody board A, B and C of 15 mm thickness.
woody board A (2)
400 mm
513 mm513 mm700 mm
woody board B (2)
Fig. 6-1-7
2) Apply black mat paint to one side of woody board A and B.
3) Attach background paper (J-2501-130-A) to woody board C.
4) Assemble so that the black sides and the background paper
side of woody board A, B and C are internal. (Fig. 6-1-8)
370 mm
700 mm730 mm
woody board A
woody board C (1)
700 mm
woody board B
woody board A
DSC-T100_ADJ
woody board C
Flash adjustment box
Background paper
woody board B
Fig. 6-1-8
L = 50cm
L
Fig. 6-1-9
6-9
Front of the lens
Camera
4. HD Station Modifying Procedure
The HD station must be modified to perform the “Component out (Y, Pb, Pr) level adjustment” in the “Video System Adjustment”.
Modify the HD station by the following steps.
1) Prepare the HD station and USB connector.
Part No.
HD station (Note)A-1242-190-A
USB connector1-794-962-11
Note: You may purchase the commercially available CSS-HD1.
2) Disassemble the HD station in the numerical order given in the following figure to remove the Connector board.
1 Pull the switch
6 Connector board/
5 Two screws
3) Mount the USB connector on the Connector board.
Multi board
Upper cabinet
4 Lower cabinet
3 Five screws
2 Two foot rubbers
Fig. 6-1-10
DSC-T100_ADJ
Connector board
Mount the USB connector.
Fig. 6-1-11
6-10
4) Connect four lead wires between USB connector and Multi board.
Wiring diagram when USB connector is added for modification
5) Puncture the Upper cabinet to make a window for the USB connector as shown below.
USB connector position
6) Assemble the HD station.
Upper cabinet
Puncture the Upper cabinet.
USB connector
Fig. 6-1-13
DSC-T100_ADJ
6-12
1-2.ADJUSTMENT PROGRAM
3
5
4
7
6
2
1
9
0
8
qa
The DSC-T100 is adjusted by the Automatic Adjustment Program.
The Automatic Adjustment Program enters automatically via the
SeusEX the adjustment operations that were formerly entered
manually by the adjustment remote commander (some items may
be adjusted by manual operation on the operation screen of the
SeusEX).
1. Precautions When Using Automatic Adjustment
Program
1) The Automatic Adjustment Program writes the adjustment re-
sults such as EVR data to the set through two-way communication with the camera via the SeusEX. Accordingly, the Automatic Adjustment Program must be used in the en vironment
where the SeusEX operates.
2) The Automatic Adjustment Program cannot be used when the
SeusEX or the SeusCam is running. Exit the SeusEX or the
SeusCam before using the Automatic Adjustment Program.
3) The SeusEX must be already started on the PC when using the
Automatic Adjustment Program. W ith the SeusEX not started,
some adjustment items will take time in adjustment.
4) The program run time may vary depending on the environ-
ment of the personal computer used.
3. Function of Each Button on Main Menu Screen
When the Automatic Adjustment Program started, the Main Menu
screen in Fig. 6-1-14 will appear. On this screen, select each adjustment section.
Fig. 6-1-14
2. Start of Automatic Adjustment Program
Double-click the application file (DSC-T100 Auto-Adj
V er_1.0r01.ex e), and the Automatic Adjustment Program will start.
1 [Connecting the Equipment] button
A connection diagram of the equipment is displayed.
2 [CONNECT] button
The mode of Camcorder is switched to the Adjustment Mode.
When the Adjustment Mode has switched normally, the operation of the buttons 4 - 0 is enabled.
3 [END] button
The mode of Camcorder is switched to the normal mode.
When the normal mode has switched correctly, the Automatic
Adjustment Program is finished.
4 [DESTINATION DATA WRITE] button
The “DESTINATION DATA WRITE” screen appears.
5 [USB SERIAL N0. INPUT] button
The “USB SERIAL No. INPUT” screen appears.
6 [VIDEO SYSTEM ADJUSTMENT] button
The “VIDEO SYSTEM ADJUSTMENT” screen appears.
7 [CAMERA SYSTEM ADJUSTMENT] button
The “CAMERA SYSTEM ADJUSTMENT” screen appears.
8 [LCD SYSTEM ADJUSTMENT] button
The “LCD SYSTEM ADJUSTMENT” screen appears.
DSC-T100_ADJ
9 [SERVICE MODE] button
The “SERVICE MODE” screen appears.
q; [DATA BACKUP] button
The “DATA BACKUP” screen appears.
qa This part indicates the version of Automatic Adjustment Pro-
gram.
6-13
Loading...
+ 35 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.