Sony DCR-DVD91E, DCR-DVD101E User Manual

Operating Insctructions [GB]

3-089-914-14 (1)

Digital Video Camera Recorder

Operating Instructions

Before operating the unit, please read this manual thoroughly, and retain it for future reference.

DCR-DVD91E/DVD101E/ DVD201E

SERIES

Welcome!

Congratulations on your purchase of this Sony Handycam. With your Handycam you can capture life’s precious moments with superior picture and sound quality. Your Handycam is loaded with advanced features, but at the same time it is very easy to use. You will soon be producing home video that you can enjoy for years to come.

WARNING

To prevent fire or shock hazard, do not expose the unit to rain or moisture.

To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

Certain countries and regions may regulate disposal of the battery used to power this product. Please consult with your local authority.

CAUTION

The use of optical instruments with this product will increase eye hazard. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

NOTICE ON THE SUPPLIED AC ADAPTOR FOR CUSTOMERS IN THE UNITED KINGDOM

A moulded plug complying with BS1363 is fitted to this equipment for your safety and convenience.

Should the fuse in the plug supplied need to be replaced, a fuse of the same rating as the supplied one and approved by ASTA or BSI to BS1362 (i.e., marked with or mark) must be used.

If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the fuse cover after you change the fuse. Never use the plug without the fuse cover. If you should lose the fuse cover, please contact your nearest Sony service station.

For the customers in Europe

Getting Started

ATTENTION

The electromagnetic fields at the specific frequencies may influence the picture and sound of this camcorder.

This product has been tested and found compliant with the limits set out in the EMC Directive for using connection cables shorter than 3 meters. (9.8 feet)

Notice

If static electricity or electromagnetism causes data transfer to discontinue midway (fail), restart the application or disconnect and connect the USB cable again.

Read this first

What you can do with your DVD Handycam

Your DVD Handycam uses DVD-R and DVD-RW as a recording media. You can enjoy your DVD Handycam in ways that are new and different from those of a tape media-based camcorder. Read the next few pages to find out how.

You can find a scene quickly using a Visual Index display.

The Visual Index display shows thumbnails of movies and still images recorded on the disc in your DVD Handycam. You can find the desired scene quickly using this convenient index.

You can play back still images, one after another.

You can play back still images one after another on your DVD Handycam. You can also enjoy the playback of still images continuously on a DVD player if you finalize the disc.

You can play back a disc recorded with your DVD Handycam on your DVD player.

You can play back a disc recorded with your DVD Handycam on DVD players that can play back DVD-R/DVD-RW.

You can edit and copy a disc easily by connecting your DVD Handycam to your computer.

You can edit and copy a disc easily on your computer using the supplied ImageMixer Ver.1.5 for Sony DVD Handycam software. It also enables you to produce your own original DVD disc.

Read this first

What is the difference between DVD-R and DVD-RW?

2 types of discs are available and they are different in the following ways.

Which disc can I use?

8cm DVD-Rs and 8cm DVD-RWs are available.

8cm DVD-R

You can use the following discs:

• DMR30 (single-sided disc)

• DMR60DS (double-sided disc)

8cm DVD-RW

You can use the following discs:

• DMW30 (single-sided disc)

• DMW60DS (double-sided disc)

How can I choose between these 2 discs?

The number of recordable times is different for the 2 discs. Choose the one that meets your needs.

DVD-Rs can be recorded only once.

They are suitable for long-term records and for making a backup copies. Recorded in VIDEO mode.

DVD-RWs can be overwritten repeatedly.

They are suitable for source gathering and temporary recordings. You can choose VIDEO mode or VR mode to make your recordings.

Discs other than these 2 types cannot be used in your DVD Handycam.

Examples of incompatible discs

• 12cm DVD-R

• 12cm DVD-RW

• DVD+R

• DVD-RAM

• DVD+RW

• DVD-ROM

• CD-R

• CD-RW

What kind of player can I use for playback?

You can play back a disc you have recorded on your DVD Handycam on other players by finalizing the disc (see page 65). The following list shows examples of players that can play back a disc recorded by your DVD Handycam. However, playback compatibility is not guaranteed with all players.*

DVD-R (VIDEO mode only)

Players compatible with the DVD Video format.

DVD player/ DVD recorder

Computer with a DVD drive installed

Read this first

DVD-RW (in VIDEO mode)

Players that can play back DVD-RWs.

DVD player/ DVD recorder

Computer with a DVD drive installed

DVD-RW (in VR mode)

Players that can play back DVD-RWs in VR mode.

DVD player/ DVD recorder

Computer with a DVD drive installed

In VIDEO mode and VR (Video Recording) mode

VIDEO mode: A disc has wide compatibility with other players. VR mode: A disc can be edited on DVD Handycam but the players are limited.

*1DVD-R/RW discs recorded by Sony DVD Handycam camcorders are designed to be compatible with

and may be played back on home DVD players, computer DVD drives and PlayStation 2 video game consoles.*

*2Playback on all home DVD players, computer DVD drives and PlayStation 2 consoles cannot be

guaranteed. Some players, drives, and video game consoles lack the ability to read due to the optical reflection standards of DVD-R/RW discs and/or due to decoding incompatibilities. Refer to the specifications of your playback equipment for additional compatibility information.

How to prepare and use your DVD Handycam

Preparing

Prepare a new disc.

• You can start recording promptly with a DVD-R.

• You need to format a DVD-RW before recording. Formatting is also required when using a once recorded

DVD-RW again.

Select a recording format (either VIDEO mode or VR mode) when using DVD-RW.

Shooting

Both movies and still images can be recorded on a single disc.

Because your movies and still images are recorded in free areas on the disc automatically, important recordings are not overwritten. If you finalize the recorded disc after shooting, you can play it back immediately on DVD players, etc..

Playing back

Select a scene to play back from the Visual Index display.

If you finalize the recorded disc after shooting, you can play it back on DVD players, etc..

Continued on the right page.

Editing

Finalizing

You can make a copy of a disc you have recorded by connecting your DVD Handycam to your computer with the supplied software.

For the recommended computer system environment, see page 91.

You can produce an original DVD by editing your movies/still images on your computer.

Finalize the disc so that it becomes compatible with other DVD players.

You may not be able to record additional material, edit, or format a disc after finalizing it, depending on the kind of the disc used.

Overwrite Edit Format

DVD-R No No No (VIDEO mode)

DVD-RW Yes* (VIDEO mode)

DVD-RW Yes* (VR mode)

No Yes*

Yes*

Read this first

*1 Unfinalizing is required. *2 Unfinalizing is not required. *3 Recorded data will be erased.

Table of contents

Read this first

What you can do with your

DVD Handycam ............................... 4

What is the difference between

DVD-R and DVD-RW? .................... 6

How to prepare and use your DVD

Handycam ......................................... 8

Getting Started

Using this manual ................................. 12

Checking the supplied accessories ..... 14

Step 1 Preparing the power source ... 15

Installing/removing the battery

pack ............................................ 15

Charging the installed battery

pack ............................................ 16

Showing the remaining battery time

– BATTERY INFO .................... 18

Connecting to a wall socket .......... 18

Step 2 Turning on the power .............. 19

Step 3 Adjusting the LCD screen and

the viewfinder ................................. 20

Adjusting the angle and the

brightness of the LCD screen...20

Adjusting the viewfinder .............. 22

Step 4 Setting the date and time ........ 23

Simple setting of the clock using a

time difference ......................... 25

Step 5 Preparing a disc for recording...26

Shooting movies/still images

Before shooting ...................................... 28

Shooting movies .................................... 29

Selecting the recording mode ....... 32

Using the zoom feature ................. 33

Shooting with the subject checking

the image – Mirror mode ........ 34

Shooting still images............................. 35

Selecting the still image quality and

size ............................................. 38

Shooting images continuously (BURST,

DCR-DVD201E only) ................... 41

Adjusting the exposure ........................ 43

Adjusting the exposure for backlit

subjects – BACK LIGHT ......... 43

Adjusting the exposure

manually ................................... 43

Shooting in the dark – NightShot plus,

etc. ..................................................... 45

Using NightShot plus .................... 45

Using Super NightShot plus ......... 45

Using the NightShot Light ............ 46

Using Color Slow Shutter.............. 46

Self-timer recording .............................. 47

On shooting movies ....................... 47

On shooting still images ................ 47

Shooting for the wide-screen TV

– 16:9 Wide mode ........................... 48

Adjusting the white balance

manually .......................................... 50

Shooting techniques to match your

circumstances – PROGRAM AE ...

Focusing manually ................................ 52

Shooting with special effects .............. 53

Using fader (for movies only)....... 53

Using special effects

– Picture effect/Digital effect .. 54

Checking/Deleting the last scene ....... 55

Checking the last scene

– Review .................................... 55

Deleting the last scene

(DVD-RWs only) ...................... 55

Viewing the recordings

Playing a disc on your camcorder ...... 56

Choosing and viewing a recording

– Visual Index ........................... 56

Various playback modes ............... 58

Displaying the indicators during

playback – Display .................. 59

Magnifying recorded images – PB

ZOOM (Playback zoom) ......... 61

Playing still images automatically

– Slide Show ............................. 62

Viewing recordings on TV ................... 63

Finalizing a disc for other players

Finalizing a disc ..................................... 65

Changing the disc title ................... 68

Playing back a disc on a DVD

player, etc. ................................. 70

Playing back a disc on a computer

with a DVD drive installed .... 71

Recording on a finalized disc

– Unfinalizing (VIDEO mode

DVD-RWs only) .............................. 73

Recording again on a used disc

– Formatting (DVD-RWs only)..... 74

Using a disc in VR mode (DVD-RWs only)

Selecting the playing order on your

camcorder – Playlist ....................... 76

Registering movies or still images in

the Playlist ................................ 76

Converting all the still images on a

disc to a movie file

– Photomovie ........................... 79

Erasing unnecessary scenes from the

Playlist ....................................... 80

Changing the order within the

Playlist ....................................... 82

Dividing a movie within

the Playlist ................................ 84

Playing the Playlist......................... 86

Editing the original data ...................... 87

Dividing a movie ............................ 87

Deleting movies/still images ....... 89

Viewing/duplicating discs/ editing the recordings on your computer (DCR-DVD101E/ DVD201E only)

Connecting your camcorder to your

computer – Introduction ............... 91

System requirements ..................... 91

Installing the USB driver ............... 92

Installing software .......................... 93

Connecting your camcorder to the

computer ................................... 94

Consulting the on-line help .......... 98

Viewing scenes recorded on your

computer .......................................... 99

Viewing scenes on the disc ........... 99

Making a disc copy

– Disc Duplicating ........................ 101

Making a disc copy ...................... 101

Editing and saving scenes.................. 102

Editing movies .............................. 102

Saving the movie

on your computer .................. 102

Creating an original disc .................... 103

Making a menu ............................. 103

Editing the contents ..................... 104

Recording on a disc ...................... 105

Connecting your camcorder to a TV and a VCR

Dubbing a disc to a tape..................... 106

Connecting your camcorder to a

VCR .......................................... 106

Dubbing to a tape ......................... 107

Dubbing a TV program or video tape

onto a disc (DCR-DVD101E/

DVD201E only) ............................. 108

Connecting your camcorder to a TV

or a VCR .................................. 108

Selecting the Video jack to be used

on the TV or the VCR ............ 108

Dubbing onto a disc ..................... 109

Customizing your camcorder

Changing the SETUP display ............ 110

Selecting the option of each item .. 111

Troubleshooting

Types of trouble and corrective

action .............................................. 118

Self-diagnosis display......................... 125

Warning indicators ............................. 126

Warning messages .............................. 127

Additional information

About the disc...................................... 129

About the “InfoLITHIUM”

battery pack ................................... 130

Using your camcorder abroad .......... 131

Maintenance information and

precautions .................................... 132

Specifications ....................................... 135

Parts and controls/Index

Identifying parts and controls ........... 137

Index ..................................................... 145

Getting Started

— Getting Started —

Using this manual

The instructions in this manual are for the 3 models listed in the table below. Before you start reading this manual and operating your camcorder, check the model number by looking at the bottom of your camcorder. The DCR-DVD201E is the model used for illustration purposes. Otherwise, the model name is indicated in the illustrations. Any differences in operation are clearly indicated in the text, for example, “DCR-DVD201E only”.

Types of differences

Model (DCR-) DVD91E DVD101E DVD201E

Image device CCD, gross approx. CCD, gross approx. CCD, gross approx.

AUDIO/VIDEO jack OUT IN/OUT IN/OUT

USB jack – zz

Note on TV color systems

TV color systems differ depending on the country or region. To view your recordings on a TV, you need an PAL system-based TV.

Television programs, films, video tapes, and other materials may be copyrighted. Unauthorized recording of such materials may be contrary to copyright laws. You cannot dub copyright protected software on your camcorder.

3.0 mm (1/6 type) 3.0 mm (1/6 type) 3.6 mm (1/5 type)

800 000 pixels 800 000 pixels 1 070 000 pixels

Contents of the recording cannot be compensated if recording or playback is not made due to a malfunction of the camcorder, storage media, etc.

Using this manual

Camcorder care

LCD display/viewfinder

The LCD display and the viewfinder are manufactured using extremely highprecision technology, so over 99.99 % of the pixels are operational for effective use. However, there may be some tiny black points and/or bright points (white, red, blue or green in color) that appear constantly on the LCD display and the viewfinder. These points are normal in the manufacturing process and do not affect the recording in any way.

Disc compatibility with other players

Discs recorded on your camcorder must be finalized to be played on other players. For details on how to finalize a disc, see “Finalizing a disc” (page 65).

Discs recorded in VIDEO mode

You must finalize a disc after all the recording is finished. You cannot record additional scene on a disc recorded in VIDEO mode once you finalize it. On DVD-RW, you can record additional scene by unfinalizing it.

Discs recorded in VR mode

Only DVD-RWs can be recorded in VR mode. Finalizing is required only when other DVD-RW compatible players cannot play the disc. You can record again with your camcorder on a finalized disc recorded in VR mode. Compatible players: DVD players that can play back DVD-RWs in VR mode.

Note

You may not be able to play certain finalized discs, depending on the disc and the players.

Getting Started

Checking the supplied accessories

Make sure that the following accessories are supplied with your camcorder.

1 Wireless Remote Commander (1)

(page 142)

2 AC-L15A/L15B AC adaptor (1),

Mains lead (1) (page 16)

3 NP-FM50 rechargeable battery pack

(1) (page 15)

4 A/V connecting cable (1)

5 6

9 0

5 Shoulder strap (1) 6 Lens cap (1) (page 28) 7 USB cable (Hi-SPEED USB compatible)

(1) (page 92)

DCR-DVD101E/DVD201E only.

8 DVD-R (DMR30) (1) 9 CD-ROM (SPVD-011 USB Driver) (1)

DCR-DVD101E/DVD201E only.

q; Cleaning cloth (1) qa 21-pin adaptor (1)

For the models with mark printed on

their bottom surfaces only.

Step 1 Preparing the power source

Installing/removing the battery pack

To install the battery pack, slide it in and up in the direction of the arrow until it clicks.

To remove the battery pack

1 Slide the battery pack in the direction of arrow while pressing the battery

release button.

2 Slide the battery pack down.

Getting Started

BATT release button

Step 1 Preparing the power source

Charging the installed battery pack

Your camcorder operates only with the “InfoLITHIUM” battery pack (M series). See page 130 for more information on the “InfoLITHIUM” battery pack.

Open the DC IN jack cover.

Mains lead

AC adaptor

POWER/CHG lamp

With the v mark on the DC plug facing up

1 Make sure that the battery pack is installed on the camcorder. 2 Open the DC IN jack cover, then connect the AC adaptor supplied with your

camcorder to the DC IN jack on your camcorder with the plug’s v mark facing up.

3 Connect the mains lead to the AC adaptor. 4 Connect the mains lead to the wall socket.

Charging begins. The POWER/CHG lamp lights in orange during the charge, then turns off when the charge is completed (full charge).

After charging the battery pack

Disconnect the AC adaptor from the DC IN jack on your camcorder.

Notes

•Prevent metallic objects from coming into contact with the metal parts of the DC plug of the AC adaptor. This may cause a short-circuit, damaging the AC adaptor.

•Place the AC adaptor near a wall socket. If any trouble occurs with this unit while using the AC adaptor, disconnect the plug from the wall socket as soon as possible to cut off the power.

•The POWER/CHG lamp may flash if the battery pack is not installed correctly or the battery pack is damaged.

Step 1 Preparing the power source

Charging time (full charge)*

Battery pack

NP-FM50 (supplied) 150

NP-QM71/QM71D 260

NP-QM91/QM91D 360

Recording time with the viewfinder*

Battery pack

NP-FM50 (supplied) 135 135 115 65 65 55

NP-QM71/QM71D 325 325 285 160 160 140

NP-QM91/QM91D 490 490 430 245 245 215

DVD91E DVD101E DVD201E DVD91E DVD101E DVD201E

Recording time with the LCD display*

Continuous Typical*

LCD BACKLIGHT is set to ON

Battery pack

NP-FM50 (supplied) 120 120 105 60 60 50

NP-QM71/QM71D 290 290 265 145 145 130

NP-QM91/QM91D 445 445 400 220 220 200

DVD91E DVD101E DVD201E DVD91E DVD101E DVD201E

Continuous Typical*

LCD BACKLIGHT is set to OFF

Battery pack

NP-FM50 (supplied) 135 135 120 65 65 60

NP-QM71/QM71D 335 335 300 165 165 150

NP-QM91/QM91D 505 505 455 250 250 225

DVD91E DVD101E DVD201E DVD91E DVD101E DVD201E

Continuous Typical*

Getting Started

Playing time*

Battery pack

NP-FM50 (supplied) 130 130 115 140 140 125

NP-QM71/QM71D 315 315 285 340 340 305

NP-QM91/QM91D 475 475 430 520 520 465

Playing time on LCD screen Playing time with LCD closed

DVD91E DVD101E DVD201E DVD91E DVD101E DVD201E

*1 Approximate number of minutes required at 25°C to charge an empty battery pack.

The charging time may increase if the battery’s temperature is extremely high or low because of the ambient temperature.

*2 Approximate number of minutes you can record when using a fully charged battery

pack.

*3 Approximate number of minutes you can record, including starting/stopping,

zooming, and turning the power on/off. The actual battery life may be shorter.

Notes

•If the power goes off even though the remaining battery time indicator indicates that the battery pack has enough power to operate, charge the battery pack fully again so that the indication on the remaining battery time indicator is correct.

•Battery pack performance decreases in low-temperature surroundings and recording may not be possible even though the battery time remaining may be as much as 20 minutes. Recharge the battery pack fully in this case.

•NP-FM30 is not recommended because of its short recording time when used with your camcorder.

Step 1 Preparing the power source

Showing the remaining battery time – BATTERY INFO

1 Open the LCD screen. 2 Press DISPLAY/BATT INFO.

The remaining battery time appears for a while on the LCD display.

BATTERY INFO

BATTERY CHARGE LEVEL 0% 50%

REC TIME AVAILABLE

LCD SCREEN VIEWFINDER::96108

100%

min min

During charging

Notes

•BATTERY INFO does not appear when the power of the camcorder is ON.

•The remaining battery time may not be indicated in the following cases: – The battery pack is not installed correctly. – The battery pack is damaged. – The battery pack is empty.

•The number displayed as Battery Info is the approximate recording time.

•While the remaining battery time is being calculated, “CALCULATING BATTERY INFO...” is displayed.

•It may take some time to display the remaining battery time after DISPLAY/BATT

INFO is pressed.

Connecting to a wall socket

When you use your camcorder for a long time, it is recommended that you power it from a wall socket using the AC adaptor.

1 Open the DC IN jack cover, then connect the AC adaptor supplied with your

camcorder to the DC IN jack on your camcorder with the plug’s v mark facing up.

2 Connect the mains lead to the AC adaptor. 3 Connect the mains lead to a wall socket.

See page 16 for details.

BATTERY INFO

BATTERY CHARGE LEVEL 0% 50% 100%

REC TIME AVAILABLE

LCD SCREEN VIEWFINDER::

120

min

135

min

Fully charged

Notes

•The AC adaptor can supply power even if the battery pack is attached to your camcorder.

•The DC IN jack has “source priority”. This means that the battery pack cannot supply any power if the AC adaptor is connected to the DC IN jack, even when the mains lead is not plugged into a wall socket.

•Your camcorder is not disconnected from the AC power source (mains) as long as it is connected to the wall socket, even if your camcorder itself has been turned off.

Step 2 Turning on the power

Press the POWER button for a few seconds. Your camcorder turns on and the POWER/ CHG lamp lights up in green. When you turn on your camcorder for the first time, the CLOCK SET display appears.

POWER/CHG lamp

POWER button

To turn the power off

Press the POWER button for a few seconds again. When the POWER/CHG lamp turns off, the power cuts off.

To set the mode dial

Rotate and set the mode dial to the operation you want to perform, such as shooting or playback.

Getting Started

: Playback/edit

Select this when you play back or edit the recorded scenes on your camcorder.

: Movies

Select this when you shoot the movies.

: Still images

Select this when you shoot the still images.

Step 3 Adjusting the LCD screen and the viewfinder

Adjusting the angle and the brightness of the LCD screen

Adjust the brightness and the angle of the LCD screen properly in your sight.

180°

90°

LCD BACKLIGHT button

90°

SETUP button

1 Open the LCD screen. 2 Adjust the direction of the LCD screen to the desired position.

When you adjust the angle of the LCD screen, make sure if the LCD screen is opened up to a full 90 degrees. You can turn the LCD screen over and then fold it back to the camcorder body with the LCD screen facing out as shown below.

To adjust the brightness of the LCD display

1 Turn the power on by pressing the POWER button for a few seconds. 2 Press SETUP.

The SETUP display appears.

MANUAL SET

PROGRAM AE P EFFECT D EFFECT WHT BAL AUTO SHTR

[ SETUP ] : END

3 Use the multi-selector to select (LCD/VF SET).

Refer to page 23 to see how to use the multi-selector.

LCD / VF SET

LCD BRIGHT LCD B. L. LCD COLOR VF B. L.

RETURN

[ SETUP ] : END

Step 3 Adjusting the LCD screen and the viewfinder

4 Use the multi-selector to select [LCD BRIGHT].

LCD / VF SET

LCD BRIGHT

[ SETUP ] : END

5 Use the multi-selector to adjust the brightness of the LCD display.

− : Get Darker

+ : Get Brighter

The LCD screen brightness is adjusted.

6 Press SETUP.

The SETUP display disappears from the LCD display.

Note

[LCD B.L.] is set to [BRT NORMAL] when you close the LCD screen facing out.

Tips

•You can change the brightness of the backlight. Select (LCD/VF SET) then [LCD B.L.] in the SETUP display when using the battery pack (page 113).

•The [LCD BRIGHT], [LCD B.L.] and [LCD COLOR] settings do not affect the brightness of the image when you are recording.

•The backlight of the LCD screen is set to ON normally. When you use the camcorder outdoors, set it to OFF so that the battery pack lasts longer.

•When you turn off the LCD back light, the icon appears on the LCD display.

Getting Started

Step 3 Adjusting the LCD screen and the viewfinder

Adjusting the viewfinder

When recording pictures with the LCD screen closed, check the picture with the viewfinder. Adjust the viewfinder lens to accommodate your eyesight so that the image in the viewfinder comes into sharp focus.

Viewfinder lens adjustment dial

1 Extend the viewfinder. 2 Turn the viewfinder lens adjustment dial until you can see the characters in the

viewfinder clearly.

Tips

•If you install a large capacity battery pack such as the NP-QM91/QM91D in your camcorder, extend the viewfinder and adjust the angle.

•You can change the brightness of the viewfinder backlight. Select [VF B.L.] in the SETUP display when using the battery pack (page 113).

•The [VF B.L.] setting does not affect the brightness of the image when you are recording.

•Recording pictures with the viewfinder is recommended in the following cases:

– When the pictures on the LCD screen are hard to see. – When you want to save on battery consumption.

Step 4 Setting the date and time

Set the date and time when you use your camcorder for the first time. Set the geographical area, then daylight savings time ([DST]), the year, the month, the day, the hour and the minute, in that order. If you do not set the date and time, the [CLOCK SET] display appears whenever you turn on your camcorder or change the mode dial. If you do not use your camcorder for about 3 months, the date and time settings may be cleared from memory because the built-in rechargeable battery in your camcorder will have been discharged during that time. In that case, charge the built-in rechargeable battery by connecting the AC adaptor, and set the date and time again (page 16, 134).

SETUP button

Getting Started

1 Open the LCD screen. 2 Turn the power on by pressing the POWER button for a few seconds.

The CLOCK SET display appears.

CLOCK SET AREA 1

Lisbon,London

DST OFF

DATE Y M D

[ ENTER ] : NEXT ITEM

+0.0GMT

3 Use the multi-selector to select the desired geographical area.

Multi-selector

NEAR FAR

Select with V/v/B/b and press the button in the center to confirm your selection.

Step 4 Setting the date and time

CLOCK SET AREA 1

Lisbon,London

DST

DATE Y M D

[ ENTER ] : NEXT ITEM

OFF ON

+0.0GMT

4 Use the multi-selector to set daylight savings time ([DST]) to [ON], if

necessary.

CLOCK SET AREA 1 +0.0GMT

Lisbon, London

DST OFF

DATE Y M D

2004 1 1

[ ENTER ] : NEXT ITEM

0 : 00

5 Use the multi-selector to set the year.

CLOCK SET AREA 1 +0.0GMT

Lisbon, London

DST OFF

DATE Y M D

2004 1

[ ENTER ] : NEXT ITEM

0 : 00

6 Set the month, day, hour and minute with the same procedure as in step 5, and

then press the button in the center. The clock starts to move. The internal clock of your camcorder operates on a 24-hour cycle.

Note

When setting the date and time, you cannot go back to a previously set item. If you make a mistake, press the SETUP button twice and re-start from the biginning of the

step by selecting (SETUP MENU) , then [CLOCK SET].

Tips

•If the CLOCK SET display does not appear in step 2, press SETUP, then select

(SETUP MENU), then [CLOCK SET] using the multi-selector.

•If the SETUP display appears after step 6, press SETUP. The SETUP display disappears.

Step 4 Setting the date and time

Simple setting of the clock using a time difference

You can easily set the clock to the local time by setting the area. In the SETUP display use the multi-selector to select (OTHERS) then [AREA SET] .

World time difference

1 234681012131416171819 20 21 22 23 24 25 26 2729 30 31

Getting Started

Area Time-zone code differences

GMT

+01:00

+02:00

+03:00

+03:30

+04:00

+04:30

+05:00

+05:30

+06:00

+06:30

+07:00

+08:00

+09:00

+09:30

+10:00

Area setting

Lisbon, London Berlin, Paris Helsinki, Cairo Moscow, Nairobi Tehran Abu Dhabi, Baku Kabul Karachi, Islamabad Calcutta, New Delhi Almaty, Dhaka Rangoon Bangkok, Jakarta HongKong, Singapore Seoul, Tokyo Adelaide, Darwin Melbourne, Sydney

Area Time-zone code differences

+11:00

+12:00

–12:00

–11:00

–10:00

–09:00

–08:00

–07:00

–06:00

–05:00

–04:00

–03:30

–03:00

–02:00

–01:00

Area setting

Solomon Is. Fiji, Wellington Eniwetok, Kwajalein Midway Is., Samoa Hawaii Alaska LosAngeles, Tijuana Denver, Arizona Chicago, Mexico City New York, Bogota Santiago St. John’s Brasilia, Montevideo Fernando de Noronha Azores

Step 5 Preparing a disc for recording

A new DVD-R or DVD-RW is required for recording. You cannot overwrite or delete data recorded on a DVD-R, but you can delete data and record again with a DVD-RW. The preparation procedure is different depending on the type of disc you use.

Notes

•When you insert or remove a disc, move the grip belt to the bottom of the camcorder so as not to obstruct the operation with your hand, etc.

•Do not apply shock or vibration to your camcorder while [DISC ACCESS] or [PREPARING TO OPEN COVER] is displayed on the LCD display.

•Formatting is required when a DVD-RW is used for the first time.

Make sure that the disc is not exposed to fingerprints and dust.

1 Set the mode dial to (Movie) or (Still). 2 Turn the power on by pressing the POWER button for a few seconds. 3 Slide the disc cover OPEN switch in the direction of the arrow mark.

Opening melody rings once, then the camcorder beeps intermittently. [PREPARING TO OPEN COVER] appears on the LCD display. After the beeps stop, the disc cover opens slightly automatically. Open the cover completely.

ACCESS lamp

4 Set the disc with the label side facing out, then press the center of the disc until

it clicks to seat it firmly on the center spindle.

Step 5 Preparing a disc for recording

5 Close the disc cover.

Your camcorder starts recognizing the inserted disc. With a DVD-R, you can start recording immediately after [DISC ACCESS] disappears on the LCD display. The FORMAT display appears when you insert a DVD-RW. Proceed to step 6.

FORMAT

REC FORMAT EXECUTE

EST. PROCESS TIME : 7sec REC FORMAT : VIDEO

VIDEO

6 Use the multi-selector to select [REC FORMAT]. 7 Use the multi-selector to select desired recording format.

Your camcorder is set in VIDEO mode as the default setting. Refer to page 7 about recording mode.

8 Use the multi-selector to select [EXECUTE]. 9 Use the multi-selector to select [YES].

The selection of the recording format is completed. The disc formatting starts. When the formatting is completed, you can start recording on the DVD-RW.

Notes

•It may take some time to recognize the disc depending on the disc type and condition.

•If you close the disc cover with the disc set incorrectly, it may cause your camcorder to

malfunction.

•You may hear the motor running when the disc cover is closed without a disc being set. This is not a malfunction.

•Do not remove the battery pack or disconnect the AC adaptor while formatting.

•You can remove the disc when a power source is connected to your camcorder even

when your camcorder is turned off. However, when you change the disc, the disc recognition process does not start automatically.

To remove the disc

It may take some time to remove the disc depending on the disc condition or recorded matrials.

1 Perform the step 3 on page 26. 2 Remove the disc.

Tips

•When you replace a disc, disc information such as the date you started to use it and information on previously recorded areas appears for about 5 seconds. The information on previously recorded areas may not be displayed correctly depending on the condition of the disc.

•See page 129 for details on disc handling.

— Shooting movies/still images —

Before shooting

Note

To shoot movies/still images correctly, note the following:

– Hold your camcorder correctly. – Do not shock or vibrate your camcorder during shooting. – Do not scratch, put the fingerprint on, or get the disc dirty.

To hold your camcorder

Hold your camcorder with your fingers inserted through the grip belt.

To attach the lens cap

Attach the lens cap to the metal fittings of the grip belt, as illustrated below, using the strap.

To fasten the grip belt

Fasten the grip belt firmly following the illustration below.

Note

Do not pick up your camcorder by the viewfinder, the LCD screen, or the battery pack.

Viewfinder LCD screen Battery pack

Shooting movies

Perform “Getting Started” from step 1 to 5 beforehand (page 15 to 27). The following operation is common with VIDEO mode and VR mode.

Recording lamp

1 Remove the lens cap by pressing both knobs on the sides of the cap.

2 Install the battery pack or connect the AC adaptor (page 15). 3 Open the LCD screen.

The image is not displayed in the viewfinder when the LCD screen opens.

4 Set the mode dial to (Movie). 5 Turn the power on by pressing the POWER button for a few seconds. 6 Insert a disc (page 26).

This sets your camcorder to standby.

STBY0:00:00

VIDEO

Shooting movies/still images

Shooting movies

7 Press START/STOP (z).

Your camcorder starts recording. [REC] appears on the LCD display. The camera recording lamp located on the front of your camcorder lights up. To stop recording, press START/STOP again.

You can operate start/stop with the REC START/STOP button on the LCD screen. This is useful when you shoot movies from a low angle.

After recording

1 Remove the disc (page 27). 2 Turn the power off by pressing the POWER button for a few seconds again. 3 Close the LCD screen. 4 Remove the battery pack or disconnect the AC adaptor.

Notes

•Make sure that the lens cap strap is not caught into the disc cover when you insert or remove a disc.

•Do not touch the built-in microphone during recording.

•When the ACCESS lamp lights on, data is being recorded on the disc. Take note of the

following when data is being recorded, or the data or the disc may be damaged.

– Do not apply shock or shake the camcorder. – Do not turn the power off. – Do not remove the battery pack or disconnect the AC adaptor. – Do not open the disc cover.

•The writing time to the disc for recording may vary depending on the recording mode

(page 32).

•There may be time difference between the point when you press START/STOP and the actual point that the recording starts/stops.

•Make sure the POWER/CHG lamp is off when you remove the power source.

REC 0:00:01

VIDEO

Tip

If you leave your camcorder powered by the battery pack for 5 minutes, your camcorder automatically turns off. This is to save battery power and to prevent battery wear. Turn the power on again by pressing the POWER button for a few seconds. You can cancel the automatic power-off by setting the (SETUP MENU) – [A. SHUT OFF] menu item to [NEVER] in the SETUP display.

+ 118 hidden pages