Sony CFD-V27L, CFD-V177L, CFD-V77S, CFD-V21L, CFD-V31L User Manual

Use TYPE I (normal) tape only.

1 Press xZ to open the tape compartment and insert a

recorded tape. Close the compartment.

With the side you want to play facing upward

2 Set FUNCTION to TAPE•CD/RADIO OFF.

3 Press N.

adjust the volume stop playback fast-forward or rewind the tape pause playback

eject the cassette

Notes on cassettes

• Break off the cassette tab from side A or B to prevent accidental recording. If you want to reuse the tape for recording, cover the broken tab with adhesive tape.

Tab for side B

• The use of a cassette with more than 90 minutes of play time is not recommended except for long, continuous recording or playback.

Do this

Turn VOLUME. Press xZ. Press M or m. Press X.

Press the button again to resume play after pause.

Press xZ.

Side A

Tab for side A

Use TYPE I (normal) tape only.

RecordingPlaying a tape

1 Press xZ to open the tape compartment and insert a

blank tape.

With the side you want to record on facing upward

2 Select the program source you want to record.

To record from the CD player

Set FUNCTION to CD and insert a CD (see "Playing a CD").

To record from the radio

Tune in the station you want (see "Listening to the radio").

3 Press z to start recording.

(N is depressed automatically).

stop recording pause recording

Tips

• Adjusting the volume or the audio emphasis will not affect the recording level.

• CFD-V21L/V27L/V31L/V177L only: If the MW/LW program makes a whistling sound after you’ve pressed r in step 3, set the FM MODE•ISS (Interference Suppress Switch) at the rear to the position that most decreases the noise.

• For the best results, use the AC power as a power source for recording.

• To erase a recording, proceed as follows: 1 Insert a tape with the recording you want to erase. 2 Set FUNCTION to TAPE•CD/RADIO OFF. 3 Press z.

Press

Press the button again to resume recording.

Tr oubleshooting

General

The power does not come on.

• Connect the AC power cord securely.

• Make sure the batteries are inserted correctly.

• Replace all the batteries with new ones if they are weak.

There is no audio.

• Make sure the FUNCTION selector is set to the function you want to operate.

• Adjust the volume.

• Unplug the headphones when listening through speakers.

Noise is heard.

• Someone is using a portable telephone or other equipment that emits radio waves near the player. tMove the portable telephone, etc., away from the player.

Radio

The audio is weak or has poor quality.

• Replace all the batteries with new ones if they are weak.

• Move the player away from the TV.

The picture of your TV becomes unstable.

• If you are listening to an FM program near the TV with an indoor antenna, move the player away from the TV.

CD Player

The CD does not play or “00 -- --” lights in the display even when a CD is in place.

• Make sure that the CD compartment is closed.

• Place the CD with the label surface up.

• Clean the CD.

• Take out the CD and leave the CD compartment open for about an hour to dry moisture condensation.

• Make sure the FUNCTION selector is set to CD.

The sound drops out.

• Reduce the volume.

• Clean the CD, or replace it if the CD is badly damaged.

• Place the player in a location free from vibration.

• Clean the lens with a commercially available blower.

• The sound may drop out or noise may be heard if the CD is recorded using a personal computer(CD-R,etc.).

Tape Player

The tape does not move when you press an operation button.

• Close the cassette compartment securely.

The REC z button does not function or the tape does not play or record.

• Make sure the safety tab on the cassette is in place.

• Make sure the FUNCTION selector is set to CD, AM or FM. (CFD-V27/V177)

• Make sure the FUNCTION selector is set to CD or RADIO. (CFD-V21L/V27L/V31L/V177L/ V77S)

Poor or distorted playback, recording or erasing quality.

• Clean the heads, pinch roller and capstan with a cleaning swab slightly moistened with cleaning fluid or alcohol.

• Replace all the batteries with new ones if they are weak.

• TYPE II (high position) or TYPE IV (metal) tape is being used. Use TYPE I (normal) tape only.

• Demagnetize the heads using a commercially available tape head demagnetizer.

Record/playback head

Capstan

Erase head

Pinch roller

Lens

After trying the above remedies, if you still have problems, unplug the AC power cord and remove all the batteries. After all the indications in the display disappear, plug the power cord and insert the batteries again. If the problem persists, please consult your nearest Sony dealer.

Specifications

CD player section

System

Compact disc digital audio system

Laser diode properties

Material: GaAlAs Wave length: 780 nm Emission duration: Continuous Laser output: Less than 44.6 µW (This output is the value measured at a distance of about 200 mm from the

objective lens surface on the optical pick-up block with 7 mm aperture.)

Spindle speed

200 r/min (rpm) to 500 r/min(rpm) (CLV)

Number of channels

Frequency response

20 - 20,000 Hz +1/–2 dB

Wow and flutter

Below measurable limit

Radio section

Frequency range

CFD-V21L/V31L

FM Italy 87.5 - 108 MHz

Other models 87.6 - 107 MHz

MW Italy 526.5 - 1,606.5kHz

Other models 531 - 1,602kHz

LW Italy 148.5 - 283.5 kHz

Other models 153 - 279kHz

CFD-V27/V177

FM Korea 87.6 - 107 MHz

Other models 87.6 - 108 MHz

AM Korea 531 - 1,602 kHz

Other models 530 - 1,605 kHz

CFD-V27L/V177L

FM Italy 87.5 - 108 MHz

Central and Eastern Europe Other models 87.6 - 107 MHz

MW Italy 526.5 - 1,606.5 kHz

Other models 531 - 1,602 kHz

LW Italy 148.5 - 283.5 kHz

Other models 153 - 279 kHz

CFD-V77S

FM Italy 87.5 - 108 MHz

Central and Eastern Europe Other European models and

Saudi Arabia Other models 87.6 - 108 MHz

MW Italy 526.5 - 1,606.5 kHz

Other European models Other models 530 - 1,605 kHz

SW1 2.3 - 7 MHz SW2 7 - 22 MHz

FM: 10.7 MHz AM/MW/LW/SW: 455 kHz

Aerials

FM/SW: Telescopic aerial AM/MW/LW: Built-in ferrite bar aerial

Cassette-corder section

Recording system

4-track 2 channel stereo

Fast winding time

Approx. 120 s (sec.) with Sony cassette C-60

Frequency response

TYPE I (normal): 70 - 10,000 Hz

or 87.6 - 107 MHz

or 531 - 1,602 kHz

65 - 108 MHz

87.6 - 107 MHz

531 - 1,602 kHz or 531 - 1,602 kHz

General

Speaker

CFD-V21L/V27/V27L/V31L/V177/V177L: Full range: 10 cm dia., 3.2 ohms, cone type (2) CFD-V77S: Full range: 10 cm dia., 6 ohms, cone type (2)

Outputs

Headphones jack (stereo minijack) For 16 - 68 ohms impedance

headphones Maximum power output (excluding Korean model)

CFD-V21L/V27/V27L/V31L/V177/V177L:

2.3 W + 2.3 W

CFD-V77S: 4.5 W + 4.5 W Power output (CFD-V27 Korean model)

1.6 W + 1.6 W (at 3.2 ohm, 10 %

harmonic distortion in AC operation) Power requirements

For CD radio cassette-corder

Europe

230 V AC, 50 Hz

Korea

220 V AC, 60 Hz

Other countries

110 - 127, 220 - 240 V AC selectable,

50/60 Hz

or 230 V AC, 50 Hz

9 V DC, 6 R20 (size D) batteries Power consumption

CFD-V21L/V27/V27L/V31L/V177/V177L:

Korean model: AC 15 W

Other models: AC 20 W

CFD-V77S: AC 25 W Battery life

For CD radio cassette-corder:

CFD-V21L/V27/V27L/V31L/V177/V177L

FM recording

Sony R20P: approx. 13.5 h

Sony alkaline LR20: approx. 20 h

Tape playback

Sony R20P: approx. 7.5 h

Sony alkaline LR20: approx. 15 h

CD playback

Sony R20P: approx. 2.5 h

Sony alkaline LR20: approx. 7 h

CFD-V77S

FM recording

Sony R20P: approx. 3.5 h

Sony alkaline LR20: approx. 10 h

Tape playback

Sony R20P: approx. 1.5 h

Sony alkaline LR20: approx. 5 h

CD playback

Sony R20P: approx. 1 h

Sony alkaline LR20: approx. 4 h

Dimensions

Approx. 420 × 165 × 256 mm (w/h/d)

⁄8 × 6 1⁄2 × 10 1⁄8 inches) (incl.

(16

projecting parts) Mass (incl. batteries)

CFD-V21L/V27/V27L/V31L/V177/V177L:

Approx. 4.1 kg (9 lb. 1 oz)

CFD-V77S: Approx. 4.2 kg (9 lb. 4 oz) Supplied accessory

AC power cord (1)

Design and specifications are subject to change without notice.

Optional accessories

Sony MDR headphone series

CD Radio CassetteCorder

Operating Instructions

CFD-V21L CFD-V27 CFD-V27L CFD-V31L CFD-V77S CFD-V177 CFD-V177L

3-043-560-12(1)

Precautions

On safety

• As the laser beam used in the CD player section is harmful to the eyes, do not attempt to disassemble the casing. Refer servicing to qualified personnel only.

• Should any solid object or liquid fall into the player, unplug the player, and have it checked by qualified personnel before operating it any further.

Cleaning the cabinet

• Clean the cabinet, panel and controls with a soft cloth slightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder, or solvent, such as alcohol or benzine.

On power sources

• For AC operation, check that the player‘s operating voltage is identical with your local power supply (see “Specifications”) and use the supplied AC power cord; do not use any other type. The voltage selector is located at the bottom of the player (CFD-V77S except European models).

• The player is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the player itself has been turned off.

WARNING

To prevent fire or shock hazard, do not expose the player to rain or moisture.

To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

Information

For customers in Europe

This Compact Disc player is classified as a CLASS 1 LASER product.

The CLASS 1 LASER PRODUCT label is located on the bottom exterior.

• For battery operation, use six size D (R20) batteries.

• When the batteries are not to be used, remove them to avoid damage that can be caused by battery leakage or corrosion.

• The nameplate indicating operating voltage, power consumption, etc. is located at the bottom.

On placement

• Do not leave the player in a location near heat sources, or in a place subject to direct sunlight, excessive dust or mechanical shock.

• Do not place the player on an inclined or unstable place.

• Do not place anything within 10 mm of the side of the cabinet. The ventilation holes must be unobstructed for the player to operate properly and prolong the life of its components.

• If the player is left in a car parked in the sun, be sure to choose a location in the car where the player will not be subjected to the direct rays of the sun.

• Since a strong magnet is used for the speakers, keep personal credit cards using magnetic coding or spring-wound watches away from the player to prevent possible damage from the magnet.

WARNING

Do not install the appliance in a confined space, such as a bookcase or built-in cabinet.

The FUNCTION selector is located at the front.

When you turn on the player, the OPR/BATT indicator lights up.

Notice for customers in the United Kingdom

A moulded plug complying with BS 1363 is fitted to this equipment for your safety and convenience.

Should the fuse in the plug supplied need to be replaced, same rating fuse approved by ASTA or BSI to BS 1362,

(i.e. marked with or mark) must be used.

If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the fuse cover after you change the fuse. Never use the plug without the fuse cover. If you should lose the fuse cover, please contact your nearest Sony service station.

On operation

• If the player is brought directly from a cold to a warm location, or is placed in a very damp room, moisture may condense on the lenses inside the CD player section. Should this occur, the player will not operate properly. In this case, remove the CD and wait about an hour for the moisture to evaporate.

• If the player has not been used for a long time, set it in the playback mode to warm it up for a few minutes before inserting a cassette.

If you have any questions or problems concerning your player, please consult your nearest Sony dealer.

English

About this manual

The instructions in this manual are for the CFD-V21L, CFD-V27, CFDV27L, CFD-V31L, CFD-V77S, CFDV177 and CFD-V177L. Before you start reading, check your model number. The CFD-V27L is the model used for illustration purposes.

Any differences in operation are clearly indicated in the text, for example, “CFD-V77S only,” and also in the chart below.

Model number

CFD-V27/V177 CFD-V21L/V27L/

V31L/V177L CFD-V77S

Band

FM, AM FM, MW,LW

FM, SW1, SW2, MW

Location of controls

Playing a CD Listening to the radio

REC PLAY REW FF

STOP/EJECT

PAUSE

VOLUME

MEGA BASS

i (headphones) jack

Choosing Power Sources

Connecting the AC power cord

Insert one end of the supplied AC power cord to the AC IN socket located at the rear of the player, and the other end to the wall outlet.

DISPLAY ENTER

Tape compartment

PLAY MODE

TONE

FUNCTION

OPR/BATT indicator x

CFD-V77S except European models: Adjusting the voltage

Be sure to set the VOLTAGE SELECTOR (at the bottom) to your local power supply.

Tip

Only for the customers supplied with an AC plug adaptor:

Use the supplied AC plug adaptor if the plug of the AC power cord does not match your outlet.

CD compartment

TUNING

BAND*

Z PUSH OPEN/CLOSE

.,>

* CFD-V21L/V27L/V31LV177L/V77S only

1 Press Z PUSH OPEN/CLOSE down to open the CD

compartment and place a CD in the CD compartment.

With the labeled side up

2 Close the CD compartment.

3 Set FUNCTION to CD.

4 Press u .

The player plays all the tracks once.

Using the display

Checking the total track number and playing time

Check the display in stop mode.

Total playing time Total track number

Checking the remaining time

Press DISPLAY•ENTER while playing a CD.

To display

remaining time on the current track*

remaining time on the CD and the number of tracks left

playing time and the current track number

* For a track whose number is more than 20, the remaining time appears as

“- -:- -” in the display.

Press DISPLAY•ENTER

once

twice

three times

Repeat Play

1 Set FUNCTION to CD. 2 Proceed as follows:

To repeat

a single track

all the tracks

tracks in random order

programmed tracks

Do this

1 Press PLAY MODE until “REP 1”

appears.

2 Select the track by pressing the . or

> and press u.

1 Press PLAY MODE until “REP ALL”

appears.

2 Press u. 1 Press PLAY MODE until “SHUF REP”

appears.

2 Press u. 1 Press PLAY MODE until “PGM REP”

appears.

2 Program tracks (see step 3 on Program

Play).

3 Press u.

Program Play

1 Set FUNCTION to CD. 2 Press PLAY MODE until “PGM” appears in the display. 3 Press . or > then press DISPLAY•ENTER for the tracks

you want to program in the order you want.

Playing order

Programmed track

4 Press u to start Program Play.

To cancel Program Play

Press PLAY MODE until “PGM” disappears from the display.

To change the current program

Press x once if the CD is stopped and twice if the CD is playing. The current program will be erased. Then create a new program following the programming procedure.

Tips

• You can play the same program again, since the program is saved until you open the CD compartment or switch FUNCTION.

• You can record your own program. After you’ve created the program, insert a blank tape and press z to start recording.

Notes on CDs

• Before playing, clean the CD with a cleaning cloth. Wipe the CD from the center out.

1 CFD-V21L/V27L/V31L/V177L/V77S: Set FUNCTION to

RADIO. CFD-V27/V177: Set FUNCTION to FM or AM and proceed to step 3.

CFD-V21L/V27L/V31L/V177L/V77S CFD-V27/V177

2 CFD-V21L/V27L/V31L/V177L/V77S: Select the band.

CFD-V21L/V27L/V31L/V177L

CFD-V77S

3 Turn TUNING to tune in a radio station.

If the received FM stereo is too weak, the reception becomes monaural.

CFD-V77S only: For better SW reception, use FINE TUNE.

adjust the volume turn off the radio

To improve broadcast reception

Reorient the antenna for FM. Reorient the player itself for AM, MW or LW. For SW, extend the antenna vertically.

Do this

Turn VOLUME. Set FUNCTION to TAPE•CD/RADIO

OFF.

1 to AC IN

Using the player on batteries

Insert six size D (R20) batteries (not supplied) into the battery compartment.

2 to a wall outlet

Notes

• Replace the batteries when the OPR/BATT indicator dims or when the player stops operating. Replace all the batteries with new ones. Before you replace the batteries, be sure to take out the CD from the player.

• To use the player on batteries, disconnect the AC power cord from the player.

Adjusting the sound emphasis (TONE/MEGA BASS)

Adjusting the tone

Turn TONE. Turn the control toward HIGH to enhance the high tone and toward

LOW to enhance the low tone.

Reinforcing the bass sound

Press MEGA BASS to $ON. To return to normal sound, press the button to 4OFF.

adjust the volume stop playback pause playback

go to the next track go back to the previous track remove the CD turn off the player

locate a point while listening to the sound

locate a point while observing the display

Track number Playing time

Do this

Turn VOLUME. Press x. Press u.

Press again to resume play after pause. Press >. Press .. Press Z PUSH OPEN/CLOSE. Set FUNCTION to TAPE•CD/RADIO

OFF. Hold down > (forward) or .

(backward) while playing until you find the point.

Hold down > (forward) or . (backward) in pause until you find the point.

To cancel Repeat Play

Press PLAY MODE until “REP” disappears from the display.

Shuffle Play

1 Set FUNCTION to CD. 2 Press PLAY MODE until “SHUF” appears in the display. 3 Press u to start Shuffle Play.

To cancel Shuffle Play

Press PLAY MODE until “SHUF” disappears from the display.

• Do not use solvents such as benzine, thinner, commercially available cleaners or anti-static spray intended for vinyl LPs.

• Do not expose the CD to direct sunlight or heat sources such as hot air ducts, nor leave it in a car parked in direct sunlight as there can be a considerable rise in temperature inside the car.

• Do not stick paper or sticker on the CD, nor scratch the surface of the CD.

• After playing, store the CD in its case.

If there is a scratch, dirt or fingerprints on the CD, it may cause tracking error.

For FM

For SW

Tips

• To listen through headphones, connect the headphones to the i (headphones) jack.

• For best results, place the player away from a TV.

• CFD-V21L/V27L/V31L/V177L/V77S only To receive FM stereo program: Set the FM MODE selector at the rear to STEREO. If the FM broadcast

is noisy, set the selector to MONO and the radio will play in monaural.

For AM/MW/LW