Sony CFD-V177L User Manual [en, es]
3-865-316-32 (1)
CD Radio
Cassette-Corder
Operating Instructions page 2
Manual de instrucciones página 2
GB
CFD-V27
CFD-V27L
CFD-V77S
CFD-V177
GB
ES
ES
CFD-V177L
1999 by Sony Corporation
Warning
To prevent fire or shock hazard, do
not expose the player to rain or
moisture.
Notice for customers in the United
Kingdom
A moulded plug complying with BS 1363 is
fitted to this equipment for your safety and
convenience.
To avoid electrical shock, do not open
the cabinet. Refer servicing to
qualified personnel only.
Information
For customers in Europe
This Compact Disc player is classified as
a CLASS 1 LASER product.
The CLASS 1 LASER PRODUCT label is
located on the bottom exterior.
WARNING
Do not install the appliance in a confined
space, such as a bookcase or built-in cabinet.
The FUNCTION selector is located at the
front.
When you turn on the player, the OPR/BATT
indicator lights up.
Should the fuse in the plug supplied need to
be replaced, same rating fuse approved by
ASTA or BSI to BS 1362, (i.e. marked with
or mark) must be used.
If the plug supplied with this equipment has
a detachable fuse cover, be sure to attach the
fuse cover after you change the fuse. Never
use the plug without the fuse cover. If you
should lose the fuse cover, please contact
your nearest Sony service station.
About this manual
The instructions in this manual are for the
CFD-V27, CFD-V27L, CFD-V77S, CFD-V177
and CFD-V177L. Before you start reading,
check your model number. The CFD-V27L is
the model used for illustration purposes.
Any differences in operation are clearly
indicated in the text, for example, “CFD-V77S
only,” and also in the chart below.
Model number Band
CFD-V27/V177 FM, AM
CFD-V27L/V177L FM, MW, LW
CFD-V77S FM, SW1, SW2, MW
GB
2
Introduction
Table of contents
Basic Operations
4 Playing a CD
6 Listening to the radio
8 Playing a tape
10 Recording on a tape
The CD Player
12 Using the display
13 Locating a specific point in a
track
14 Playing tracks repeatedly
(Repeat Play)
15 Playing tracks in random order
(Shuffle Play)
16 Creating your own program
(Program Play)
Setting Up
17 Choosing the power sources
18 Adjusting the sound emphasis
(TONE/MEGA BASS)
Additional Information
19 Precautions
21 Troubleshooting
23 Maintenance
24 Specifications
26 Index
Basic Operations
GB
Introduction
GB
3
Basic Operations
Playing a CD
3 4 1,2
Connect the supplied AC power cord (see page 17).
1 Press 6 PUSH OPEN/CLOSE
down to open the CD
compartment and place a CD on
the CD compartment.
2 Close the CD compartment.
3 Set FUNCTION to CD.
GB
Basic Operations4
With the label side up
4 Press ^ .
The player plays all the tracks
once.
Display
Basic Operations
Track number
Playing time
Use these buttons for additional operations
6 PUSH OPEN/CLOSE
^VOLUME
p
=, +
FUNCTION
To Do this
adjust the volume Turn VOLUME.
stop playback Press p.
pause playback Press ^.
go to the next track Press +.
go back to the previous track Press =.
remove the CD Press 6 PUSH OPEN/
turn off the player Set FUNCTION to TAPE•
Press again to resume play
after pause.
CLOSE.
CD/RADIO OFF.
Basic Operations
GB
5
Listening to the radio
12 3
Connect the supplied AC power cord (see page 17).
1 CFD-V27L/V177L/V77S:
Set FUNCTION to RADIO.
CFD-V27L/V177L/V77S CFD-V27/V177
CFD-V27/V177:
Set FUNCTION to FM or
AM and proceed to step 3.
2 CFD-V27L/V177L/V77S:
Select the band.
CFD-V27L/V177L CFD-V77S
3 Turn TUNING to tune in a
radio station.
If the received FM stereo is
too weak, the reception
becomes monaural.
CFD-V77S only: For better
SW reception, use FINE
TUNE.
GB
Basic Operations6
Use these buttons for additional operations
FUNCTIONVOLUME
Basic Operations
Tip
CFD-V27L/V177L/V77S
only
To receive FM stereo
program:
Set the FM MODE
selector at the rear to
STEREO. If the FM
broadcast is noisy, set
the selector to MONO
and the radio will play
in monaural.
To Do this
adjust the volume Turn VOLUME.
turn off the radio Set FUNCTION to TAPE•
CD/RADIO OFF.
To improve broadcast reception
Reorient the antenna for FM. Reorient the player itself
for AM, MW or LW. For SW, extend the antenna
vertically.
For FM
For AM/MW/LW
For SW
Basic Operations
GB
7
Playing a tape
321
Connect the supplied AC power cord (see page 17).
1 Press p6 to open the tape
compartment and insert a
recorded tape. Use TYPE I
(normal) tape only. Close the
compartment.
2 Set FUNCTION to TAPE •CD/
RADIO OFF.
3 Press (.
GB
Basic Operations8
With the side you want
to play facing upward
Use these buttons for additional operations
VOLUMEPp60, )
To Do this
adjust the volume Turn VOLUME.
stop playback Press p6.
fast-forward or rewind the tape Press ) or 0.
pause playback Press P.
Press the button again to
resume play after pause.
eject the cassette Press p6.
Basic Operations
Basic Operations
GB
9
Recording on a tape
31
Connect the supplied AC power cord (see page 17).
2
1 Press p6 to open the tape
compartment and insert a blank
tape. Use TYPE I (normal) tape
only.
With the side you want to
record on facing upward
2 Select the program source you
want to record.
To record from the CD player, set
FUNCTION to CD and insert a
CD (see page 4).
To record from the radio, tune in
the station you want (see page 6).
GB
Basic Operations10
Display
3 Press r to start recording. (( is
depressed automatically.)
Use these buttons for additional operations
p6
P
Basic Operations
Tips
• Adjusting the volume or
the audio emphasis
(page 18) will not affect
the recording level.
• CFD-V27L/V177L only:
If the MW/LW program
makes a whistling
sound after you’ve
pressed r in step 3, set
the FM MODE•ISS
(Interference Suppress
Switch) at the rear to the
position that most
decreases the noise.
• For the best results, use
the AC power as a
power source for
recording.
• To erase a recording,
proceed as follows:
1 Insert a tape you want
to erase its recording.
2 Set FUNCTION to
TAPE•CD/RADIO
OFF.
3 Press r.
To Press
stop recording p6
pause recording P
Press the button again to
resume recording.
Basic Operations
11
GB
The CD Player
Using the display
You can check information about the CD
using the display.
Checking the total track number and playing
time
Check the display in stop mode.
DISPLAY
ENTER
Total playing time
Total track number
Checking the remaining time
Press DISPLAY•ENTER while playing a CD.
To display Press DISPLAY•ENTER
remaining time on the once
current track*
remaining time on the CD twice
and the number of tracks left
playing time and the current three times
track number
* For a track whose number is more than 20, the remaining
time appears as “- -:- -” in the display.
GB
The CD Player12
Locating a specific
point in a track
You can locate a specific point in a track
while playing a CD using + or =.
To locate Press
a point while listening to + (forward) or =
the sound (backward) while playing
a point while observing + (forward) or =
the display (backward) in pause and
=, +
The CD Player
and hold down until you
find the point.
hold down until you find
the point.
The CD Player 13
GB
Playing tracks
repeatedly
(Repeat Play)
You can play tracks repeatedly in
normal, shuffle or program play
modes (see page 16).
1 Set FUNCTION to CD.
2 Proceed as follows:
PLAY MODE
FUNCTION
To repeat Do this
a single track 1 Press PLAY MODE until
“REP 1” appears.
2 Select the track by
pressing the = or + and
press ^.
all the tracks 1 Press PLAY MODE until
“REP ALL” appears.
2 Press ^.
tracks in random order 1 Press PLAY MODE until
“SHUF REP” appears.
2 Press ^.
programmed tracks 1 Press PLAY MODE until
“PGM REP” appears.
2 Program tracks (see step 3
on page 16).
3 Press ^.
=,+
^
To cancel Repeat Play
Press PLAY MODE until “REP” disappears from the
display.
GB
The CD Player14
Playing tracks in
random order
(Shuffle Play)
^FUNCTIONPLAY MODE
You can play tracks in random order.
1 Set FUNCTION to CD.
2 Press PLAY MODE until the “SHUF” appears in
the display.
3 Press ^ to start shuffle play.
To cancel Shuffle Play
Press PLAY MODE until “SHUF” disappears from the
display.
The CD Player
The CD Player 15
GB
Creating your
own program
(Program Play)
You can arrange the playing
order of up to 20 tracks on a CD.
PLAY MODE
FUNCTION
DISPLAY
ENTER
=,+
^
Tips
• You can play the same
program again, since
the program is saved
until you open the CD
compartment or switch
FUNCTION.
• You can record your
own program. After
you’ve created the
program, insert a blank
tape and press r to
start recording.
1 Set FUNCTION to CD.
2 Press PLAY MODE until “PGM” appears in the
display.
3 Press the = or + then press DISPLAY•
ENTER for the tracks you want to program in the
order you want.
Playing order
Programed track
4 Press ^ to start program play.
To cancel Program Play
Press PLAY MODE until “PGM” disappears from the
display.
To change the current program
Press p once if the CD is stopped and twice if the CD
is playing. The current program will be erased. Then
create a new program following the programing
procedure.
GB
The CD Player16
Loading...