CFD-S26
SERVICE MANUAL
Ver 1.2 2002. 06
Photo: SILVER
CD
Section
TC
Section
US Model
E Model
Australian Model
Model Name Using Similar Mechanism CFD-S22/S32
CD Mechanism Type KSM-213CDP
Optical Pick-up Name KSS-213C
Model Name Using Similar Mechanism CFD-V5
Tape Transport Mechanism Type MF-V5-117
AUDIO POWER SPECIFICATIONS (US model)
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION
With 3.2-ohm loads, both channels driven from
150 - 6,300 Hz; rated 1.8 W per channelminimum RMS power, with no more than 10%
total harmonic distortion in AC operation.
Other Specifications
CD player section
System
Compact disc digital audio system
Laser diode properties
Material: GaAlAs
Wave length: 780 nm
Emission duration: Continuous
Laser output: Less than 44.6 µW
(This output is the value measured at a distance of
about 200 mm from the objective lens surface on
the optical pick-up block with 7 mm aperture.)
Spindle speed
200 r/min (rpm) to 500 r/min (rpm) (CLV)
Number of channels
2
Frequency response
20 - 20,000 Hz +1/–2 dB
Wow and flutter
Below measurable limit
SPECIFICATIONS
Radio section
Frequency range
FM: 87.6 - 108 MHz
US, E92, MX model:
AM: 530 - 1,710 kHz
SP, AR, AUS, E4 model:
AM: 531 - 1,602 kHz (9 kHz step)
AM: 530 - 1,610 kHz (10 kHz step)
Antennas
FM: Telescopic antenna
AM: Built-in ferrite bar antenna
Cassette-corder section
Recording system
4-track 2 channel stereo
Fast winding time
Approx. 120 sec. with Sony cassette C-60
Frequency response
TYPE I (normal): 80 - 10,000 Hz
– Continued on next page –
9-873-112-13
2002F0400-1
© 2002. 06
CD RADIO CASSETTE-CORDER
Sony Corporation
Personal Audio Company
Published by Sony Engineering Corporation
1
CFD-S26
General
Speaker
Full range: 10 cm dia.,
3.2 ohms, cone type (2)
Outputs
Headphones jack (stereo minijack)
For 16 - 68 ohms impedance headphones
Power output (excluding US model)
2.3 W + 2.3 W (at 3.2 ohms, 10 %
harmonic distortion in AC operation)
Power requirements
For CD radio cassette-corder:
US, E92, MX model:
120 V AC, 60 Hz
SP, AR, AUS model:
230 V AC, 50 Hz
E4 model:
110 - 120 V/220 - 240 V AC selectable, 50/60 Hz
9 V DC, 6 size D (R20) batteries
Power consumption
AC 20 W
Battery life
For CD radio cassette-corder:
FM recording
Sony R20P: approx. 13.5 h
Sony alkaline LR20: approx. 20 h
Tape playback
Sony R20P: approx. 7.5 h
Sony alkaline LR20: approx. 15 h
CD playback
Sony R20P: approx. 2.5 h
Sony alkaline LR20: approx. 7 h
Dimensions
Approx. 420 × 159 × 284 mm (w/h/d)
5/8 × 6 3/8 × 11 1/4 inches) (incl. projecting parts)
(16
Mass
Approx. 3.8 kg (8 lb. 6 oz.) (incl. batteries)
Supplied accessories
AC power cord (1)
Design and specifications are subject to change without
notice.
• Abbreviation
AR : Argentina model
AUS : Australian model
E4 : AC 110-120V/220-240V area in E model
E92 : AC 120V area in E model
MX : Mexican model
SP : Singapore model
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270˚C during
repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
Notes on Chip Component Replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
2
CFD-S26
SAFETY CHECK-OUT (US model)
After correcting the original service problem, perform the following
safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, screws,
and all other exposed metal parts for AC leakage. Check leakage as
described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a VOM
or battery-operated AC voltmeter. The “limit” indication is 0.75
V, so analog meters must have an accurate low-voltage scale. The
Simpson 250 and Sanwa SH-63Trd are examples of a passive
VOM that is suitable. Nearly all battery operated digital
multimeters that have a 2V AC range are suitable. (See Fig. A)
TABLE OF CONTENTS
1. SERVICING NOTES ......................................................... 4
2. GENERAL ............................................................................ 7
3. DISASSEMBLY
3-1. Cabinet (Front) Sub Assy .................................................... 8
3-2. Wires ................................................................................... 9
3-3. Power (1) Board, Power (2) Board...................................... 9
3-4. Voltage Select Board ......................................................... 10
3-5. Cabinet (Upper) Assy ........................................................ 10
3-6. Main Board ....................................................................... 11
3-7. CD Mechanism Block ....................................................... 11
3-8. Tape Mechanism Block ..................................................... 12
3-9. Holder Assy, Cassette ........................................................ 12
3-10. PRE Board ......................................................................... 13
3-11. Belt, M801 (Capstan/Reel Motor),
HRP301 (Head, Magnetic) ................................................ 13
3-12. Optical Pick-up ................................................................. 14
4. MECHANICAL ADJUSTMENTS ............................... 15
5. ELECTRICAL ADJUSTMENTS
Tape Section .......................................................................... 15
Tuner Section......................................................................... 16
CD Section ............................................................................ 17
To Exposed Metal
Parts on Set
0.15µF
1.5k
Ω
Earth Ground
AC
voltmeter
(0.75V)
Fig. A. Using an AC voltmeter to check AC leakage.
6. DIAGRAMS
6-1. IC Pin Description ............................................................. 18
6-2. Circuit Boards Location .................................................... 19
6-3. Block Diagram – CD Section (Former Type) – ................ 20
6-4. Block Diagram – Main Section (Former Type) – .............. 21
6-5. Printed Wiring Board – CD Section (Former Type) –....... 22
6-6. Schematic Diagram – CD Section (Former Type) – ......... 23
6-7. Printed Wiring Boards – Main Section (Former Type) – .. 24
Schematic Diagram – Main Section (1/4) (Former Type) – ..
6-8.
6-9.
Schematic Diagram – Main Section (2/4) (Former Type) – ..
6-10.
Schematic Diagram – Main Section (3/4) (Former Type) – ..
6-11.
Schematic Diagram – Main Section (4/4) (Former Type) – ..
6-12.
Printed Wiring Boards – Control Section (Former Type) – ...
6-13.
Schematic Diagrams – Control Section (Former Type) – ......
6-14.
Printed Wiring Boards – Power Supply Section (Former Type) – ..
6-15.
Schematic Diagrams – Power Supply Section (Former Type) – ....
6-16. Block Diagram – CD Section (New Type) – ..................... 33
6-17. Block Diagram – Main Section (New Type) – .................. 34
6-18. Printed Wiring Board – CD Section (New Type) – ........... 35
6-19. Schematic Diagram – CD Section (New Type) – .............. 36
6-20. Printed Wiring Boards – Main Section (New Type) – ...... 37
6-21. Schematic Diagram – Main Section (1/4) (New Type) – .. 38
6-22. Schematic Diagram – Main Section (2/4) (New Type) – .. 39
6-23. Schematic Diagram – Main Section (3/4) (New Type) – .. 40
6-24. Schematic Diagram – Main Section (4/4) (New Type) – .. 41
6-25. Printed Wiring Boards – Control Section (New Type) – ... 42
6-26. Schematic Diagrams – Control Section (New Type) – ..... 43
6-27.
Printed Wiring Boards – Power Supply Section (New Type) – ..
6-28.
Schematic Diagrams – Power Supply Section (New Type)
25
26
27
28
29
30
31
32
44
– .... 45
7. EXPLODED VIEWS
7-1. Cabinet (Front) Section ..................................................... 48
7-2. Cabinet (Rear) Section ...................................................... 49
7-3. Cabinet (Upper) Section .................................................... 50
7-4. Tape Mechanism Section-1 ............................................... 52
7-5. Tape Mechanism Section-2 ............................................... 53
7-6. Optical Pick-up Section .................................................... 54
8. ELECTRICAL PARTS LIST......................................... 55
3
CFD-S26
SECTION 1
SERVICING NOTES
CHUCK PLATE JIG ON REPAIRING
On repairing CD section, playing a disc without the lid (CD), use
Chuck Plate Jig.
• Code number of Chuck Plate Jig: X-4918-255-1
LASER DIODE AND FOCUS SEARCH OPERATION
CHECK
1. Turn ON the POWER button and press FUNCTION button to
CD position.
2. Open the lid (CD).
3. Turn on S801 with screwdriver, etc. as following figure.
4. Press the CD N X button.
5. Confirm the laser diode emission while observing the objecting
lens. When there is no emission, Auto Power Control circuit or
Optical Pick-up is broken.
Objective lens moves up and down three times for focus search.
S801
NOTE ON PERFORMING SERVICE AND INSPECTION
The main, CD, control (1), control (2), control (3), battery terminal (1), battery terminal (2), power (1) and power (2) board have two types,
former type and new type.
When performing service and inspection, check the part number on the main, CD, control (1), control (2), control (3), battery terminal (1),
battery terminal (2), power (1) and power (2) board.
– MAIN BOARD (component side) –
MAIN Board Part No.
Former type : 1-679-963-12
New type : 1-679-963-14
4
– CONTROL (1) BOARD (component side) –
– CONTROL (2) BOARD (component side) –
CONTROL (2) Board Part No.
Former type : 1-679-967-12
New type : 1-679-967-14
–
CFD-S26
CONTROL (1) Board Part No.
Former type : 1-679-966-12
New type : 1-679-966-14
– CD BOARD (component side) –
– CONTROL (3) BOARD (component side)
CD Board Part No.
Former type : 1-680-943-11
New type : 1-680-943-13
CONTROL (3) Board Part No.
Former type : 1-679-968-12
New type : 1-679-968-14
5
CFD-S26
–
–
–
– BATTERY TERMINAL (1) BOARD (component side)
BATTERY TERMINAL (1) Board Part No.
Former type : 1-679-964-12
New type : 1-679-964-14
– BATTERY TERMINAL (2) BOARD (component side)
BATTERY TERMINAL (2) Board Part No.
Former type : 1-679-965-12
New type : 1-679-965-14
– POWER (1) BOARD (component side)
POWER (1) Board Part No.
Former type : 1-679-969-12
New type : 1-679-969-14
– POWER (2) BOARD (component side) –
POWER (2) Board Part No.
Former type : 1-679-970-12
New type : 1-679-970-14
6
Location of controls
SECTION 2
GENERAL
CFD-S26
This section is extracted
from instruction manual.
N X
SLEEP
TUNE –, +
.,>
DISPLAY ENT•
MEMORY
REC PLAY REW FF
Number buttons for
CD/RADIO DIRECT OPERATION
Tape
compartment
POWER
MODE
OPR/BATT
indicator
STOP/EJECT
PAUSE
Display
Z PUSH
OPEN/CLOSE
CD
compartment
VOLUME +,–
RADIO BAND•
AUTO PRESET
x
MEGA BASS
TAPE
CD
i (headphones) jack
Tip
To listen through headphones, connect the headphones to the i (headphones) jack.
7
CFD-S26
SECTION 3
DISASSEMBLY
• The equipment can be removed using the following procedure.
Set Cabinet (Front) Sub Assy Wires
Cabinet (Upper) Assy
Power (1) Board, Power (2) Board
Voltage Select Board
Tape Mechanism Block
Holder Assy, Cassette
PRE Board
CD Mechanism Block
Optical Pick-up
Note : Follow the disassembly procedure in the numerical order given.
3-1. CABINET (FRONT) SUB ASSY
9
cabinet (front) sub assy
6
BVTP 3x12
7
CNP323
Main Board
Belt,M801(Capstan/Reel Motor),
HRP301 (Head, Magnetic)
lid (CD)
8
CNP805
3
BVTP 3x12
4
BVTP 3x12
5
BVTP 3x12
2
BVTP 3x12
1
lid, battery case
8
3-2. WIRES
)
Put flat cable and wires between the cabinets and push them in the
grooves located at A to E in the figure to prevent disconnection
before assembling the set.
CFD-S26
CABINET (FRONT
AB
from speaker
3-3. POWER (1) BOARD, POWER (2) BOARD
CD
from MAIN board
CABINET (REAR)
E
from CONTROL (1) board
3
BVTP 3x10
POWER (2) board
2
BVTP 3x10
5
CNP901
6
CNP902
4
1
BVTP 3x10
POWER (1) board
7
9
CFD-S26
y
3-4. VOLTAGE SELECT BOARD
(E4 model only)
• Abbreviation
E4 : AC 110-120V/220-240V area in E model
3-5. CABINET (UPPER) ASSY
7
handle
1
1
BVTP 3x10
BVTP 3x10
4
BVTP 3x12
2
VOLTAGE SELECT board
(E4 model only)
3
holder assy, cassette
6
BVTP 3x12
5
lid (CD)
2
BVTP 3x12
8
cabinet (upper) ass
10
cabinet (rear)
3-6. MAIN BOARD
1
6
BVTP 3x10
2
connector
(S801)
terminal, antenna
3
CNP702
5
BVTP 3x10
8
MAIN board
7
CNP301
4
CNP302
CFD-S26
3-7. CD MECHANISM BLOCK
1
PWH 2.6x10
2
PWH 2.6x10
3
CD mechanism block
(KSM-213CDP)
11
CFD-S26
k
3-8. TAPE MECHANISM BLOCK
1
BVTP 3x10
2
BVTP 3x10
3
tape mechanism bloc
(MF-V5-117)
3-9. HOLDER ASSY, CASSETTE
3
1
BVTP 3x10
2
damper
4
holder assy, cassette
12
3-10. PRE BOARD
)
3
Removal the solders.
1
BVTT 2x6
4
PRE board
2
CFD-S26
claw
claw
3-11. BELT, M801 (CAPSTAN/REEL MOTOR), HRP301 (HEAD, MAGNETIC)
6
HRP301 (head, magnetic)
1
screws
B 2.6x5
mechanism deck
5
claws
3
belt
2
4
M801
(capstan/reel motor
13
CFD-S26
3-12. OPTICAL PICK-UP
2
claws
9
optical pick-up
4
5
claw
3
1
claws
gear (A)
cover, CD
7
6
claw
8
sled shaft
14
)
SECTION 4
MECHANICAL ADJUSTMENTS
CFD-S26
SECTION 5
ELECTRICAL ADJUSTMENTS
PRECAUTION
1. Clean the following parts with a denatured-alcohol-moistened
swab :
record/playback head pinch roller
erase head rubber belts
capstan idlers
2. Demagnetize the record/playback head with a head demagnetizer. (Do not bring the head magnetizer close to the erase head.)
3. Do not use a magnetized screwdriver for the adjustments.
4. The adjustments should be performed with the rated power
supply voltage (9V) unless otherwise noted.
Torque Measurement
Mode Torque meter Meter reading
2.95 – 6.86 mN • m
FWD CQ-102C (30 – 70 g • cm)
(0.42 – 0.97 oz • inch)
FWD
Back Tension
FF CQ-201B (more than 60 g • cm)
REW CQ-201B (more than 60 g • cm)
CQ-102C (1.5 – 5.5 g • cm)
0.15 – 0.53 mN • m
(0.021 – 0.076 oz • inch)
more than 5.88 mN • m
(more than 0.83 oz • inch)
more than 5.88 mN • m
(more than 0.83 oz • inch)
TAPE SECTION 0 dB = 0.775 V
• Standard Output Level
Output terminal HP OUT
load impedance 32 Ω
output signal level 0.25 V (–10 dB)
• Test Tape
Type Signal Used for
WS-48A 3 kHz, 0 dB tape speed adjustment
Tape Speed Adjustment
Procedure:
Mode: playback
test tape
WS-48A
(3 kHz, 0 dB)
set
i jack (J321
Adjust so that the value on the digital frequency counter is
3,000 Hz.
digital frequency
counter
32 Ω
Tape Tension Measurement
Mode Tension meter Meter Reading
FWD CQ-403A
more than 100 g
(more than 3.53 oz)
Specification Value:
Digital frequency counter
2,940 to 3,060 Hz
Adjust so that the frequency at the beginning and that at the end of
tape winding are between 2,970 to 3,030 Hz.
Adjustment Location:
Tape speed adjustment
control inside motor
15
CFD-S26
)
TUNER SECTION 0 dB = 1 µV
• FM Section
Setting:
RADIO (BAND) button: FM
FM RF signal
generator
TP (JW2)
0.01 µF
75 kHz frequency
deviation by 1 kHz signal
output level : as low as possible
• AM Section
Setting:
RADIO (BAND) button: AM
AM RF signal
generator
Put the lead-wire
antenna close to
the set.
30% amplitude
modulation by
400 Hz signal
• Connecting Level Meter (FM and AM)
level meter
(range: 0.5–5 V ac
32 Ω
set
set
FM IF ADJUSTMENT
Adjust for a maximum reading on level meter.
T2
10.7 MHz
FM FREQUENCY COVERAGE
ADJUSTMENT
Frequency Display 87.5 MHz 108 MHz
Reading on Digital voltmeter 1.3 ± 0.3 V 3.0 ± 0.2 V
Adjustment Part <confirmation> L2
FM TRACKING ADJUSTMENT
Adjust for a maximum reading on level meter.
L1 CT1
87.5 MHz 108 MHz
AM IF ADJUSTMENT
Adjust for a maximum reading on level meter.
T1
450 kHz
AM FREQUENCY COVERAGE
ADJUSTMENT
Frequency Display 530 kHz 1,710 kHz
Reading on Digital voltmeter 1.0 ± 0.1 V 5.3 ± 0.7 V
Adjustment Part L4 <confirmation>
AM TRACKING ADJUSTMENT
Adjust for a maximum reading on level meter.
L3 CT3
620 kHz 1,400 kHz
i jack (J321)
• Connecting Digital Voltmeter (FM and AM)
digital
voltmeter
100 kΩ
TP (VT)
• Repeat the procedures in each adjustment several times, and the
frequency coverage and tracking adjustments should be finally
done by the trimmer capacitors.
Adjustment Location: See page 17.
16
CFD-S26
T
Adjustment Location:
– MAIN board (component side) –
L4
AM
FREQUENCY
COVERAGE
ADJUSTMENT
TP (VT)
(CONDUCTOR SIDE)
ADJUSTMENT
CT1, L1
FM
TRACKING
ADJUSTMENT
L4
CT3
ADJUSTMENT
T2
FM
IF
TP (JW1)
L2
CT1
L1
L3
L2
FM
FREQUENCY
COVERAGE
T1
AM
IF
ADJUSTMEN
T2
T1
CT3, L3
AM
TRACKING
ADJUSTMENT
CD SECTION
CD section adjustments are done automatically in this set.
In case of operation check, confirm that focus bias.
FOCUS BIAS CHECK
1. Connect the oscilloscope between IC701 pin 4 and pin qa (or
TP (RF) and TP (VREF).
2. Insert the disc (YEDS-18). (Part No. : 3-702-101-01)
3. Press the CD N X button.
4. Confirm that the oscilloscope waveform is as shown in the
figure below. (eye pattern)
A good eye pattern means that the diamond shape ( ) in the
center of the waveform can be clearly distinguished.
• RF signal reference waveform (eye pattern)
VOLT/DIV : 50 mV (10 : 1 probe in use)
TIME/DIV : 500 nS
RF level :
0.85 ± 0.2 Vp-p
When observing the eye pattern, set the oscilloscope for AC range
and raise vertical sensitivity.
Test Point:
– CD board (conductor side) –
TP
(RF)
TP
(RF)
TP
(FE)
TP
(FE)
TP
(TE)
TP
(VREF)
TP
(VREF)
17
CFD-S26
SECTION 6
DIAGRAMS
6-1. IC PIN DESCRIPTION
• IC802 uPD789477-907 (SYSTEM CONTROLLER)
Pin No. Pin Name I/O Pin Description
1, 2 NC — Not used. (Open)
3 – 5 VLC2 – 0 O LCD drive voltage output
6 – 9 COM0 – 3 O LCD drive common output
10 – 26 S0 – 16 O LCD drive segment output
27 – 29 S17 – 19 O LCD drive segment output Not used. (Open)
30 BL-CONT — Not used. (Open)
31 A-MUTE O Audio mute output H: Mute
32 WB/FM.AM.TV O Tuner output level attenuator switch Not used. (Open)
33 DBB O MEGA BASS control output H: MEGA BASS off, L: MEGA BASS on
34 P-CON O System power control output H: PCON
35 AC-CHK I AC power supply detection signal input “L”: AC in
36 CD O CD function output H: CD
37 TAPE O Tape function output H: Tape
38 AVDD — Analog power supply pin for A/D converter (+3.3 V)
39 BTT-CHK-H I Battery check input for Hi-voltage
40 BTT-CHK-M I Battery check input for Mid-voltage
41 REC I Tape record signal input H: REC
42 – 45 KEY1 – 4 I Key input
46 MODE CHK I Mode set input
47 AGND — Analog GND for A/D converter
48 REMOTE I Sircs receiver data input
49 TC-PLAY I Tape play switch input L: Tape
50 WP/INI O Initial set signal output
51 CD-DOOR I CD door open/close switch input L: Close
52 C-WRQ I CD command data input
53 C-DOUT I CD sireal data input
54 C-DIN O CD sireal data output
55 C-CLK I Serial data transfer clock signal input
56 R-COUNT I Tuner PLL data input
57 R-DATA O Tuner PLL data output
58 R-CLK O Tuner PLL clock output
59 R-LAT O Tuner PLL latch output
60 B-MUTE O Tuner mute signal output H: Mute
61 C-DRF I CD DRF signal input
62 C-CE O CD SENSE read clock output
63 C-FSEQ I CD frame SYNC input
64 C-XRT O CD system reset output
65 V-LAT O Volume latch output Not used. (Open)
66 V-DATA O Volume data output
67 V-CLK O Volume clock output
68 SUR O Surround switch signal output Not used. (Open)
69 ICO — Connected to GND
70 XT1 I Sub system oscillation input (32.768 kHz)
71 XT2 O Sub system oscillation output (32.768 kHz)
72 VDD — Main power supply pin for A/D converter (+3.3 V)
73 VSS — Main GND
74 X1 I Main system oscillation input (4.19 MHz)
18
Pin No. Pin Name I/O Pin Description
75 X2 O Main system oscillation output (4.19 MHz)
76 RST I System reset input
77 ISS1 O ISS1 output Not used. (Open)
78 ISS2 O ISS2 output Not used. (Open)
79 SCL O EEPROM clock output
80 SDA I/O EEPROM input/output
6-2. CIRCUIT BOARDS LOCATION
POWER (1) board
POWER (2) board
PRE board
CFD-S26
VOLTAGE SELECT board
(E4 model only)
CONTROL (1) board
CONTROL (3) board
CONTROL (2) board
BATTERY TERMINAL (1) board
MAIN board
CD board
BATTERY TERMINAL (2) board
19 19
CFD-S26
6-3. BLOCK DIAGRAM — CD SECTION (FORMER TYPE) —
CD BOARD MAIN BOARD (1/2)
CNP701
A
C
B
D
LD
PD
E
F
VREF
12
10
11
13
7
5
14
9
16
A
C
B
D
LD
PD
E
F
VREF
LD POWER
CONTROLLER
Q701
VREF
FIN2
FIN1
7
LDD
80
79
9
10
11
LDS
TIN1
TIN2
TE
VREF
APC
PH/BH
LCHO
RCHO
42
45
RF
48
CONVERTER
D/A
EFMIN
3
AGC
HFL
PH(RFENV)
FE
TE
VREF
SLICE
LEVEL
CONTROL
A/D
CONVERTER,
SERVO
PROCESSOR
CLV,CAV
CONTROL
SWITCH
ERROR
CORRECTION
AUDIO CD
FRAME SYNC
DETECT,PROTECT
INSERT
EFM DECODER
GENERAL
PURPOSE
PORT
INTERPOLATION
MUTE
&
ATTENUATION
DEEMPHASIS
SYSTEM SERVO PROCESSOR,
DIGITAL SIGNAL PROCESSOR
PLL
VCEC
COMMAND
INTERFACE
RF AMP,
IC701
8FS
DIGITAL
FILTER
&
1-bit DAC
GENERATOR
LPF
CLOCK
CNP702(2/2) CNP804(2/2)
CD R
12
33
CNP806(1/3)
CD_IN_ L
1
(Page 21)
OPTICAL PICK-UP
BLOCK
(KSS-213C)
TRACKING
COIL
FOCUS
COIL
M702
SLED
MOTOR
M701
SPINDLE
MOTOR
S701
(LIMIT)
M
M
3
2
4
1
PUSH
Signal path
: CD
R-ch : same as L-ch.
Abbreviation
AUS : Australian model
SP : Singapore model
E92 : AC 120V area in E model
T+
T–
F+
F–
SL+
SL–
SP+
SP–
S801
OPEN/
CLOSE
KH803
1
2
CD 3.3V
12
11
17
18
26
27
T+
T–
F+
F–
SL+
SL–
SP+
2
SP–
1
SLED/SPINDLE
MOTOR DRIVER,
TRACKING/FOCUS
COIL DRIVER
CD DOOR
SWITCH
IC702
Q820
TRACKING
COIL
DRIVE
FOCUS
COIL
DRIVE
SLED
MOTOR
DRIVE
SPINDLE
MOTOR
DRIVE
CD +3.3V
REG
Q957
51
CD DOOR
CD 6V
TIN
9
FIN
19
7
MUTE
SLIN
25
SPIN
3
VREF
23
OPIN
15
2
(Page 21)
CD
20
TD
FD
SL
SP
CD +6.9V
SWITCH
Q817,818
TDDTD
FDD
21 22 23
FD
VREF
SPDO
SP
SLDO
SL
BTT-CHK-M
40
BATTERY
CHECK
Q804,806
BTT-CHK-H
39
CONTROLLER
Q819,D802
RADIO 6V
VDD(SW)
SP MODEL
POWER
CNP702(1/2)
CNP804(1/2)
SYSTEM CONTROLLER
IC802 (1/2)
P-CON
34
SP MODEL
D951
US, E, AUS
MODEL
CONT1
FSEQ
FSEQ
C-FSEQ
CONT4
+3.3V REG
IC801
AUDIO+6V
REG
Q955,D953
POWER
SWITCH
Q952,953
POWER
SWITCH
Q951
RES
XRT
C-XRT
CD
23
SP MODEL
DRF
67
31 72 25 66 63 61 62 49 4865 64
43 10 98 76
11 12 5 6 7 8 9 10
DRF
61 63 54 62 55 52 5364
C-DRF
3.3V
D952
DICECL
CE
DIN
C-CE
C-DIN
AC-CHK
35
Q801
CL
WRQ
WRQ
C-CLK
DO
DOUT
C-WRQ
C-DOUT
KH321
5
XOUT
XIN
X701
33.86MHz
CNP902
1 1
22
33
D901 - 904 F902
BATT.COM
AC-HI
VDD
RECT
AUS,SP MODEL
US,E92 MODEL
POWER (1)
KH903 KH905
121
2
POWER (2)
BOARD
CNP901
1
3
BOARD
T901
POWER
TRANSFORMER
CNP903(1/2)
1
CNP903(2/2)
3
BATTERY
TERMINAL(1)
BOARD
(IEC DESIGNATION R20)
CNP904
4
1
2
DRY BATTERY
SIZE " D "
6PCS,9V
BATTERY
TERMINAL(2)
BOARD
CNJ901
AC IN
4.5V
4.5V
2020
6-4. BLOCK DIAGRAM — MAIN SECTION (FORMER TYPE) —
CFD-S26
(Page 20)
1
HRP301
RECORD/PLAYBACK
L-CH
R-CH
ERASE HEAD
CD_IN_L
HEAD
HE301
ANT1
FM
TELESCOPIC
ANTENNA
PRE BOARD
CNP301 (1/3)
3
S301
(REC/PB)
REC
PB
CNP301 (2/3)
CNP806 (2/3)
VDD(SW)
R.RO
9
R.IN
8
R.LINE
S16
LP-OUT
AM
OSC
AM
MIX
D1 D2
FM
MIX
FM
OSC
2124
14
L.RO
4
L.LINE
24
L.IN
5
6
REF
REC
21 22 16
T301
REC BIAS OSC
TUNER
R-LAT
5759 58 56
1 2 3 4
AM IN
FM IN
11 12
1920
OSC-OUT
MIX-OUT
FM OSC
L2L1 CT1
RADIO6V
CD_IN_R
-1
-2
6V
911
911
AUDIO 6V
SCL
SAD
7980
65
EEPROM
IC803
D324
CT3
TRACKING
CT3,L3
AM
AM
FREQUENCY
COVERAGE
D3
L3
AM
FERRITE-ROD
ANTENNA
RADIO 6V
CT1,L1
FM
TRACKING
L4
RADIO 6V
REC
41
REC
|
S0
COM0|COM3
10–266 – 9
LIQUID CRYSTAL
DISPLAY PANEL
LCD801
18
L4
RADIO 6V
AM OSC
AM
RF-IN
22 4 6
FM
RF-IN
2
FM
RF-OUT
DET
ALC 2
RADIO L
L.RAD
Q301
R-DATA
FM STEREO DEMODULATOR
FREQUENCY
COVERAGE
TU_IN_L
SYSTEM CONTROLLER
IC802 (2/2)
R-CLK
R-COUNT
XT171XT2
70
X801
32.768kHz
PLL
IC2
XOUT
T1
T1
AM IF
XIN
X1
75kHz
IC1
RADIO 6V
RADIO 6VRADIO 6V
20 19
FM/AM FRONT-END, IF DET,
L2
FM
REC/PB
PRE AMP
IC301
R.RAD
TU_IN_R
74X175
X802
4.19MHz
CF4
7
CF2
CNP301
(3/3)
TAPE
37
TAPE
R-CH
81
81
BUFFER
RESET
IC804
3.3V
IF IN
10
IF-OUT
IF
5
7
RST
76
1
2
L.LO
20
R.LO
18
LINE
17
TAPE
15
X2
MO/ST
13
14 17 13 18
LPF2/MO-ST
AM
IF-IN
FM
IF-IN
MAIN BOARD (2/2)
CNP806
(3/3)
5
CD
7
BAND8ST-IND
7
IF CUT
LPF1/BAND
AM
DET
BUFFER
FM
DET
QUAD
10
T2
RADIO 6V
CD
Q814
ST-IND
AF
T2
FM IF
VOLUME/SOUND CONTROLLER
LINE
AMP
Q125
60
DET-OUT
8
B-MUTE
16 15
VIN2
IC302
LOGIC
CONTROL
CLOCK4DATA
5
6736 66
V-CLK
VOL
MPX-IN
VOUT2
V-DATA
CD
(Page 20)
FM
MPX
IF CUT
POWER AMP
IC304
31
A-MUTE
11 5
49
TC-PLAY
LEVEL
DETECT
D323
TAPE
SWITCH
Q808
KEY142KEY243KEY344KEY4
7
MEGA
BASS
CONTROLLER
Q122
D322
MUTE
Q124
2
33
DBB
MODE CHK50WP/INI
46
Q813
Q812,D807
R-CH
45
5432
5432 8
D803
VDD(SW)
8
CNP805
CNP401
VDD(SW)
MOTOR
SWITCH
Q807
CONTROL (1)
CNP323
CNP302
3
4
1
2
1
2
3
4
CAPSTAN/REEL
SP301
SPEAKER
(L-CH)
SP302
SPEAKER
(R-CH)
S802
(TAPE PLAY)
M
M801
MOTOR
J321
i
BOARD
MUTE
R-OUT
L-OUT
KEY4
KEY3
KEY1
KEY2
KH402
41
41
11
R-CH
12
CNP404 KH405
CONTROL (2)
BOARD
S416-427
S413,414
S401-406
S411,412S407-409
CONTROL (3)
BOARD
12
12
D451
OPR/BATT
KH403
Signal path
: FM
: AM
: TAPE PLAY
: TAPE REC
: CD
21 21
R-ch : same as L-ch.
CFD-S26
6-5. PRINTED WIRING BOARD — CD SECTION (FORMER TYPE) — • Refer to page 19 for Circuit Boards Location.
THIS NOTE IS COMMON FOR PRINTED WIRING
BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is
printed in each block.)
Common Note on Schematic Diagrams:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/
specified.
f
•
• C : panel designation.
Note: The components identified by mark 0 or dotted line
• A : B+ Line.
• H : adjustment for repair.
• Total current is measured with no cassette installed.
• Power voltage is dc 9V and fed with regulated dc power
• Voltages are taken with a VOM (Input impedance 10 MΩ).
• Waveforms are taken with a oscilloscope.
• Circled numbers refer to waveforms.
• Signal path.
• Abbreviation
Common Note on Printed Wiring Boards:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
•
• : Pattern from the side which enables seeing.
• Abbreviation
: internal component.
with mark 0 are critical for safety.
Replace only with part number specified.
supply from battery terminal.
Voltage variations may be noted due to normal production tolerances.
Voltage variations may be noted due to normal production tolerances.
F : FM
f : AM
E : PB
a : REC
J : CD
AR : Argentina model.
AUS : Australian model.
E4 : AC 110-120V/220-240V area in E model.
E92 : AC 120V area in E model.
MX : Mexican model.
SP : Singapore model.
f
: internal component.
AR : Argentina model.
AUS : Australian model.
E4 : AC 110-120V/220-240V area in E model.
E92 : AC 120V area in E model.
MX : Mexican model.
SP : Singapore model.
4
W or less unless otherwise
A
B
C
D
E
F
G
1
MAIN
BOARD
CNP804
(Page 24)
2345678910
• Semiconductor
Location
Ref. No. Location
IC701 D-5
IC702 I-4
Q701 G-5
FY
TYFXTX
TP(R-CH)
1
TP(L-CH)
TP
(RF)
TP
(TE)
TP
(FE)
TP
(VREF)
H
J
I
1-680-943-
2222
6-6. SCHEMATIC DIAGRAM — CD SECTION (FORMER TYPE) — • Refer to page 22 for Common Note on Schematic Diagrams and page 46 for IC Block Diagrams.
CFD-S26
(Page 26)
IC B/D
IC B/D
• Voltage and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : CD PLAY
• Waveforms (Mode: PLAY)
500mV/div 0.5µsec/div
1
IC7014 (RF)
23 23
0.85±0.2Vp-p
100mV/div 20µsec/div
2
Approx. 100mVp-p
IC701qd (FE)
100mV/div 20µsec/div
3
1.8V 1.8V
Approx. 100mVp-p
IC701qg (TE)
1V/div 0.05µsec/div
4
IC701rk (XOUT)
3.2Vp-p
33.86MHz
CFD-S26
6-7. PRINTED WIRING BOARDS — MAIN SECTION (FORMER TYPE) — • Refer to page 19 for Circuit Boards Location and page 22 for Common Note on Printed Wiring Boards.
• Semiconductor
Location
Ref. No. Location
D1 D-3
D2 D-4
D3 D-4
D10 B-2
D11 B-2
D322 H-9
D323 G-10
D324 C-9
D802 H-9
D803 C-9
D806 G-8
D807 G-9
<D951> D-10
<D952> E-9
D953 E-10
D957 E-9
IC1 C-3
IC2 C-5
(IC301) H-3
IC302 F-9
IC304 F-11
IC801 F-6
IC802 H-7
IC803 F-5
IC804 G-5
A
B
C
D
1
MAIN BOARD
234567891011
ANT1
FM
TELESCOPIC
ANTENNA
AUS,SP MODEL
(VT)
TP
(Page 22)
CD BOARD
CNP702
1
SP MODEL
US,E,AUS MODEL
SP MODEL
13 14
Q122 G-9
Q124 F-10
Q125 F-8
Q222 F-9
Q224 F-10
Q225 E-8
(Q301) G-2
Q801 H-9
Q804 G-9
Q806 H-9
Q807 C-11
Q808 C-9
Q812 G-8
Q813 G-8
Q814 C-6
Q817 E-9
Q818 E-8
Q819 H-9
Q820 E-5
<Q951> D-11
Q952 D-10
Q953 D-10
Q955 E-9
Q957 E-8
< > : SP MODEL ONLY
( ) : PRE BOARD
E
F
G
H
S801
Z PUSH OPEN/CLOSE
L3
AM
FERRITE-ROD
ANTENNA
SP MODEL
SP MODEL
POWER (1) BOARD
3
CNP902
(Page 31)
2
I
L-CH
R-CH
1-679-592-
CONTROL (1) BOARD
CNP401
(Page 29)
LIQUID CRYSTAL DISPLAY PANEL
LCD801
1-679-963-
J
2424
6-8. SCHEMATIC DIAGRAM — MAIN SECTION (1/4) (FORMER TYPE) — • Refer to page 22 for Common Note on Schematic Diagrams and page 46 for IC Block Diagrams.
CFD-S26
IC B/D
IC B/D
(Page 26)
• Voltage and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : FM
( ) : AM
25 25
• Waveform
0.5V/div 5µsec/div
1
IC2 w; (XOUT)
1.5Vp-p
75kHz
CFD-S26
6-9. SCHEMATIC DIAGRAM — MAIN SECTION (2/4) (FORMER TYPE) — • Refer to page 22 for Common Note on Schematic Diagrams and page 47 for IC Block Diagrams.
IC B/D
(Page 28)
(Page 27)
• Waveforms
2V/div 10µsec/div
1
4.19MHz
IC802 ug (X2)
5Vp-p
2
2V/div 10µsec/div
32.768kHz
IC802 ua (XT2)
5Vp-p
(Page 30)
(Page 25)
(Page 23)
• Voltage and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : FM
( ) : PB
< > : REC
[ ] : CD PLAY
2626
6-10. SCHEMATIC DIAGRAM — MAIN SECTION (3/4) (FORMER TYPE) — • Refer to page 22 for Common Note on Schematic Diagrams and page 47 for IC Block Diagrams.
IC B/D
CFD-S26
(Page 26)
(Page 32)
27 27
• Voltage is dc with respect to ground under no-signal
(detuned) condition.
no mark : FM
( ) : PB
< > : REC
[ ] : CD PLAY
CFD-S26
6-11. SCHEMATIC DIAGRAM — MAIN SECTION (4/4) (FORMER TYPE) — • Refer to page 22 for Common Note on Schematic Diagrams and page 47 for IC Block Diagrams.
IC B/D
• Waveform
0.1V/div 5µsec/div
1
Q301 C (REC)
19.5µsec
4Vp-p
(Page 26)
• Voltage and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : FM
( ) : PB
< > : REC
[ ] : CD PLAY
2828
6-12. PRINTED WIRING BOARDS — CONTROL SECTION (FORMER TYPE) — • Refer to page 19 for Circuit Boards Location and page 22 for Common Note on Printed Wiring Boards.
CFD-S26
A
B
C
D
1
CONTROL (1) BOARD
2345678910
(Page 24)
MAIN BOARD
2
CNP805
( )
VOLUME+
–
5
6
>10
0/10
4
9
3
8
2
11 12 13 14 15
1
POWER
SLEEP
7
E
F
G
H
I
CONTROL
CD
TAPE
MEGA BASS
(TEST A)
(2)
BOARD CONTROL
RADIO BAND •
AUTO PRESET
x
> +
TUNE
. –
N X
OPR/BATT
DISPLAY
MEMORY
(TEST B)
ENT •
MODE
(3)
BOARD
1-679-968-
1-679-966-
1-679-967-
• Semiconductor
Location
Ref. No. Location
D451 H-11
29 29
CFD-S26
6-13. SCHEMATIC DIAGRAMS — CONTROL SECTION (FORMER TYPE) — • Refer to page 22 for Common Note on Schematic Diagrams.
(Page 26)
• Voltage is dc with respect to ground under no-signal
(detuned) condition.
no mark : FM
3030
6-14. PRINTED WIRING BOARDS — POWER SUPPLY SECTION (FORMER TYPE) — • Refer to page 19 for Circuit Boards Location and page 22 for Common Note on Printed Wiring Boards.
CFD-S26
A
B
C
D
1
23456789101112
BATTERY TERMINAL (2) BOARD
DRY BATTERY
SIZE " D "
(IEC DESIGNATION R20)
3PCS, 4.5V
DRY BATTERY
SIZE " D "
(IEC DESIGNATION R20)
3PCS, 4.5V
BATTERY TERMINAL (1) BOARD
E
F
G
H
1-679-965-
1-679-964-
POWER (1) BOARD
AUS,SP
MODEL
T901
POWER
TRANSFORMER
WHT
RED
US,E92 MODEL
I
1-679-969-
POWER (2) BOARD
1-679-970-
WHT
RED
• Semiconductor
Location
Ref. No. Location
D901 G-2
D902 G-1
D903 I-2
D904 H-1
J
3
MAIN BOARD
KH321
(Page 24)
31 31
CFD-S26
6-15. SCHEMATIC DIAGRAMS — POWER SUPPLY SECTION (FORMER TYPE) — • Refer to page 22 for Common Note on Schematic Diagrams.
(Page 27)
3232
6-16. BLOCK DIAGRAM — CD SECTION (NEW TYPE) —
CD BOARD MAIN BOARD (1/2)
CNP701
A
C
B
D
LD
PD
E
F
VREF
12
10
11
13
7
5
14
9
16
A
C
B
D
LD
PD
E
F
VREF
LD POWER
CONTROLLER
Q701
VREF
FIN2
FIN1
7
LDD
80
79
9
10
11
LDS
TIN1
TIN2
TE
VREF
APC
PH/BH
CFD-S26
LCHO
RCHO
42
45
RF
48
CONVERTER
D/A
EFMIN
3
AGC
HFL
PH(RFENV)
FE
TE
VREF
SLICE
LEVEL
CONTROL
A/D
CONVERTER,
SERVO
PROCESSOR
CLV,CAV
CONTROL
SWITCH
ERROR
CORRECTION
AUDIO CD
FRAME SYNC
DETECT,PROTECT
INSERT
EFM DECODER
GENERAL
PURPOSE
PORT
INTERPOLATION
MUTE
&
ATTENUATION
DEEMPHASIS
SYSTEM SERVO PROCESSOR,
DIGITAL SIGNAL PROCESSOR
PLL
VCEC
COMMAND
INTERFACE
RF AMP,
IC701
8FS
DIGITAL
FILTER
&
1-bit DAC
GENERATOR
LPF
CLOCK
CNP702 (2/2) CNP804 (2/2)
CD R
12
33
CNP806 (1/3)
CD_IN_ L
1
(Page 34)
OPTICAL PICK-UP
BLOCK
(KSS-213C)
TRACKING
COIL
FOCUS
COIL
M702
SLED
MOTOR
M701
SPINDLE
MOTOR
S701
(LIMIT)
M
M
Signal path
: CD
R-ch : same as L-ch.
Abbreviation
E4 : AC 110-120V/220-240V
area in E model
E92 : AC 120V area in E model
SP : Singapore model
MX : Mexican model
AUS: Australian model
AR : Argentina model
3
2
4
1
PUSH
T+
T–
F+
F–
SL+
SL–
SP+
SP–
S801
OPEN/
CLOSE
KH803
1
2
CD 3.3V
T+
12
T–
11
F+
17
F–
18
SL+
26
SL–
27
SP+
2
SP–
1
SLED/SPINDLE
MOTOR DRIVER,
TRACKING/FOCUS
COIL DRIVER
CD DOOR
SWITCH
Q820
TRACKING
COIL
DRIVE
FOCUS
COIL
DRIVE
SLED
MOTOR
DRIVE
SPINDLE
MOTOR
DRIVE
IC702
CD +3.3V
REG
Q957
TIN
9
FIN
19
7
MUTE
SLIN
25
SPIN
3
VREF
23
OPIN
15
CD DOOR
51
E4,E92,MX,AUS,SP,AR
MODEL
ICP301
US MODEL
CD 6V
CD
2
(Page 34)
20
TD
FD
SL
SP
CD +6.9V
SWITCH
Q817,818
TDDTD
21 22 23
VREF
FDD
FD
SPDO
SP
SLDO
SL
BTT-CHK-M
40
BATTERY
CHECK
Q804,806
BTT-CHK-H
39
E4,E92,MX,AUS,
SP,AR MODEL
CONTROLLER
Q819,D802
RADIO 6V
VDD (SW)
POWER
CNP702 (1/2)
CNP804 (1/2)
SYSTEM CONTROLLER
IC802 (1/2)
P-CON
34
E4,E92,MX,AUS,
SP,AR MODEL
D951
US MODEL
CONT1
FSEQ
DRF
67
43 10 9876
11 12 5 6 7 8 9 10
DRF
61 63 54 62 55 52 5364
C-DRF
3.3V
D952
JC556
CONT4
CD
RES
XRT
C-XRT
23
E4,E92,MX,AUS,
SP,AR MODEL
31 72 25 66 63 61 62 49 4865 64
FSEQ
C-FSEQ
+3.3V REG
IC801
AUDIO+6V
REG
Q955,D953
POWER
SWITCH
Q952,953
POWER
SWITCH
Q951
DICECL
CE
DIN
C-CE
C-DIN
AC-CHK
35
Q801
CL
WRQ
WRQ
C-CLK
DO
5
DOUT
C-WRQ
C-DOUT
KH321
XOUT
XIN
X701
33.86MHz
CNP902
1 1
22
33
E4,SP,AUS,AR MODEL
D901 – 904
RECT
US,E92,MX MODEL
BATT.COM
AC-HI
VDD
KH903 KH905
F902
JW923
POWER (1)
BOARD
121
CNP901
2
POWER (2)
BOARD
1
3
T901
POWER
TRANSFORMER
CNP903 (1/2)
1
CNP903 (2/2)
3
BATTERY
TERMINAL (1)
BOARD
E4 MODEL
VOLTAGE
SELECT
BOARD
S901
VOLTAGE SELECTOR
220-240V 110-120V
CNP905
DRY BATTERY
(IEC DESIGNATION R20)
CNP904
4
1
2
BATTERY
TERMINAL (2)
13
SIZE " D "
6PCS,9V
BOARD
CNJ901
AC IN
4.5V
4.5V
33 33
CFD-S26
6-17. BLOCK DIAGRAM — MAIN SECTION (NEW TYPE) —
(Page 33)
1
HRP301
RECORD/PLAYBACK
HEAD
L-CH
R-CH
ERASE HEAD
TELESCOPIC
CD_IN_L
HE301
ANT1
FM
ANTENNA
PRE BOARD
CNP301 (1/3)
3
S301
(REC/PB)
REC
PB
CNP301 (2/3)
CNP806 (2/3)
VDD(SW)
R.RO
9
R.IN
8
R.LINE
S16
LP-OUT
AM
OSC
AM
MIX
D1 D2
FM
MIX
FM
OSC
2124
14
L.RO
4
L.LINE
24
L.IN
5
6
REF
REC
21 22 16
T301
REC BIAS OSC
TUNER
R-LAT
5759 58 56
1 2 3 4
AM IN
FM IN
11 12
1920
OSC-OUT
MIX-OUT
FM OSC
L2L1 CT1
RADIO6V
CD_IN_R
-1
-2
6V
911
9
AUDIO 6V
SCL
SAD
7980
65
EEPROM
IC803
D324
CT3
TRACKING
CT3,L3
AM
AM
FREQUENCY
COVERAGE
D3
L3
AM
FERRITE-ROD
ANTENNA
RADIO 6V
CT1,L1
FM
TRACKING
L4
RADIO 6V
REC
11
41
REC
|
S0
COM0|COM3
10–266 – 9
LIQUID CRYSTAL
DISPLAY PANEL
LCD801
18
L4
RADIO 6V
AM OSC
AM
RF-IN
22 4 6
FM
RF-IN
2
FM
RF-OUT
DET
ALC 2
RADIO L
L.RAD
SYSTEM CONTROLLER
R-CLK
R-COUNT
XT171XT2
70
X801
32.768kHz
XOUT
20 19
T1
T1
AM IF
L2
FM
TU_IN_L
IC802 (2/2)
PLL
IC2
XIN
X1
75kHz
IC1
RADIO 6V
RADIO 6VRADIO 6V
Q301
R-DATA
FM/AM FRONT-END, IF DET,
FM STEREO DEMODULATOR
FREQUENCY
COVERAGE
REC/PB
PRE AMP
IC301
R.RAD
TU_IN_R
X175X2
74
4.19MHz
CF4
7
CF2
CNP301
(3/3)
L.LO
20
R-CH
18
17
15
TAPE
81
81
37
TAPE
RESET
IC804
3.3V
MO/ST10IF IN
13
14 17 13 18
LPF2/MO-ST
IF
BUFFER
X802
AM
IF-IN
FM
IF-IN
R.LO
LINE
TAPE
5
7
RST
76
1
2
IF-OUT
MAIN BOARD (2/2)
CNP806
(3/3)
5
CD
7
BAND8ST-IND
7
IF CUT
LPF1/BAND
AM
DET
BUFFER
FM
DET
QUAD
10
T2
RADIO 6V
CD
Q814
ST-IND
AF
T2
FM IF
LINE
AMP
Q125
B-MUTE
60
DET-OUT
VOLUME/SOUND CONTROLLER
16 15
IC302
LOGIC
CONTROL
CLOCK4DATA
5
6736 66
V-CLK
VOL
MPX-IN
VOUT2
V-DATA
VIN2
8
CD
(Page 33)
FM
MPX
IF CUT
POWER AMP
IC304
31
A-MUTE
11 5
49
TC-PLAY
LEVEL
DETECT
D323
TAPE
SWITCH
Q808
KEY142KEY243KEY344KEY4
7
MEGA
BASS
CONTROLLER
Q122
D322
MUTE
Q124
2
33
DBB
MODE CHK50WP/INI
46
Q813
Q812,D807
R-CH
45
5432
5432 8
D803
VDD(SW)
8
CNP805
CNP401
VDD(SW)
MOTOR
SWITCH
Q807
CONTROL (1)
CNP323
CNP302
3
4
1
2
1
2
3
4
CAPSTAN/REEL
MOTOR
SP301
SPEAKER
(L-CH)
SP302
SPEAKER
(R-CH)
S802
(TAPE PLAY)
M
M801
J321
i
BOARD
MUTE
R-OUT
L-OUT
KEY4
KEY3
KEY1
KEY2
KH402
41
41
11
R-CH
12
CNP404 KH405
CONTROL (2)
BOARD
S416-427
S413,414
S401-406
S411,412S407-409
CONTROL (3)
BOARD
12
12
D451
OPR/BATT
KH403
Signal path
: FM
: AM
: TAPE PLAY
: TAPE REC
: CD
R-ch : same as L-ch.
3434
6-18. PRINTED WIRING BOARD — CD SECTION (NEW TYPE) — • Refer to page 19 for Circuit Boards Location and page 22 for Common Note on Printed Wiring Boards.
CFD-S26
A
B
C
D
E
1
MAIN
BOARD
CNP804
(Page 37)
2345678910
• Semiconductor
Location
Ref. No. Location
IC701 D-5
IC702 I-4
Q701 G-5
FY
TY
TP(L-CH)
TP(R-CH)
1
TP
(RF)
TP
(FE)
FX
TX
TP
(TE)
TP
(VREF)
F
G
H
I
J
1-680-943-
13
(13)
35 35
CFD-S26
6-19. SCHEMATIC DIAGRAM — CD SECTION (NEW TYPE) — • Refer to page 22 for Common Note on Schematic Diagrams and page 46 for IC Block Diagrams.
(Page 39)
IC B/D
IC B/D
• Voltage and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : CD PLAY
• Waveforms (Mode: PLAY)
500mV/div 0.5µsec/div
1
0.85±0.2Vp-p
IC7014 (RF)
3636
100mV/div 20µsec/div
2
Approx. 100mVp-p
IC701qd (FE)
100mV/div 20µsec/div
3
1.8V 1.8V
Approx. 100mVp-p
IC701qg (TE)
1V/div 0.05µsec/div
4
IC701rk (XOUT)
3.2Vp-p
33.86MHz
6-20. PRINTED WIRING BOARDS — MAIN SECTION (NEW TYPE) — • Refer to page 19 for Circuit Boards Location and page 22 for Common Note on Printed Wiring Boards.
CFD-S26
• Semiconductor
Location
Ref. No. Location
D1 D-3
D2 D-4
D3 D-4
D10 B-2
D11 B-2
D322 I-9
D323 G-10
D324 B-10
D802 H-10
D803 B-10
D806 G-9
D807 G-9
<D951> D-10
<D952> E-10
D953 E-10
D957 E-9
IC1 C-3
IC2 C-5
(IC301) H-3
IC302 F-10
IC304 E-11
IC801 F-6
IC802 H-8
IC803 F-5
IC804 G-6
A
B
C
D
1
MAIN BOARD
234567891011
ANT1
FM
TELESCOPIC
ANTENNA
E4,AUS,SP,AR
MODEL
TP
(VT)
(Page 35)
CD BOARD
CNP702
1
E4,E92,MX,AUS,
SP,AR MODEL
US MODEL
13 14
US MODEL
E4,E92,MX,AUS,
SP,AR MODEL
Q122 G-10
Q124 F-11
Q125 F-9
Q222 F-10
Q224 F-11
Q225 E-8
(Q301) G-2
Q801 H-10
Q804 G-10
Q806 H-10
Q807 C-11
Q808 C-10
Q812 G-9
Q813 G-9
Q814 C-6
Q817 E-9
Q818 E-8
Q819 H-10
Q820 E-5
<Q951> D-12
Q952 D-10
Q953 D-11
Q955 E-10
Q957 E-9
< > : E4, E92, MX, AUS,
SP, AR MODEL ONLY
( ) : PRE BOARD
E
F
G
H
S801
Z PUSH OPEN/CLOSE
L3
AM
FERRITE-ROD
ANTENNA
US,E4,AUS,
SP,AR MODEL
SP MODEL
US MODEL
POWER (1) BOARD
3
CNP902
(Page 44)
I
L-CH
R-CH
1-679-592-
11
(11)
2
CONTROL (1) BOARD
CNP401
(Page 42)
LIQUID CRYSTAL DISPLAY PANEL
LCD801
1-679-963-
14
(14)
J
37 37
CFD-S26
6-21. SCHEMATIC DIAGRAM — MAIN SECTION (1/4) (NEW TYPE) — • Refer to page 22 for Common Note on Schematic Diagrams and page 46 for IC Block Diagrams.
IC B/D
• Voltage and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : FM
( ) : AM
IC B/D
• Waveform
0.5V/div 5µsec/div
1
(Page 39)
1.5Vp-p
75kHz
IC2 w; (XOUT)
3838
6-22. SCHEMATIC DIAGRAM — MAIN SECTION (2/4) (NEW TYPE) — • Refer to page 22 for Common Note on Schematic Diagrams and page 47 for IC Block Diagrams.
CFD-S26
(Page 41)
(Page 40)
IC B/D
• Waveforms
2V/div 10µsec/div
1
4.19MHz
IC802 ug (X2)
5Vp-p
2V/div 10µsec/div
2
32.768kHz
IC802 ua (XT2)
5Vp-p
39 39
(Page 43)
(Page 38)
(Page 36)
• Voltage and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : FM
( ) : PB
< > : REC
[ ] : CD PLAY
CFD-S26
6-23. SCHEMATIC DIAGRAM — MAIN SECTION (3/4) (NEW TYPE) — • Refer to page 22 for Common Note on Schematic Diagrams and page 47 for IC Block Diagrams.
IC B/D
(Page 39)
(Page 45)
• Voltage is dc with respect to ground under no-signal
(detuned) condition.
no mark : FM
( ) : PB
< > : REC
[ ] : CD PLAY
4040
6-24. SCHEMATIC DIAGRAM — MAIN SECTION (4/4) (NEW TYPE) — • Refer to page 22 for Common Note on Schematic Diagrams and page 47 for IC Block Diagrams.
IC B/D
CFD-S26
• Waveform
0.1V/div 5µsec/div
1
Q301 C (REC)
19.5µsec
4Vp-p
(Page 39)
• Voltage and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : FM
( ) : PB
< > : REC
[ ] : CD PLAY
41 41
CFD-S26
6-25. PRINTED WIRING BOARDS — CONTROL SECTION (NEW TYPE) — • Refer to page 19 for Circuit Boards Location and page 22 for Common Note on Printed Wiring Boards.
A
B
C
D
E
1
CONTROL (1) BOARD
2345678910
(Page 37)
MAIN BOARD
2
CNP805
( )
VOLUME+
–
MEGA BASS
5
6
>10
0/10
4
9
3
8
(
TEST A
2
)
11 12 13 14 15
1
POWER
SLEEP
7
1-679-966-
14
(14)
F
G
H
I
CONTROL
CD
(2)
TAPE
BOARD
RADIO BAND •
AUTO PRESET
1-679-967-
14
(14)
x
> + . –
TUNE
OPR/BATT
N X
CONTROL
DISPLAY
ENT •
MEMORY
)
TEST B
(
MODE
(3)
BOARD
1-679-968-
14
(14)
• Semiconductor
Location
Ref. No. Location
D451 H-11
4242
6-26. SCHEMATIC DIAGRAMS — CONTROL SECTION (NEW TYPE) — • Refer to page 22 for Common Note on Schematic Diagrams.
CFD-S26
(Page 39)
• Voltage is dc with respect to ground under no-signal
(detuned) condition.
no mark : FM
43 43
CFD-S26
6-27. PRINTED WIRING BOARDS — POWER SUPPLY SECTION (NEW TYPE) — • Refer to page 19 for Circuit Boards Location and page 22 for Common Note on Printed Wiring Boards.
A
B
C
D
E
1
23456789101112
BATTERY TERMINAL (2) BOARD
1-679-965-
1-679-965-
(14)
BATTERY TERMINAL (1) BOARD
DRY BATTERY
SIZE " D "
(IEC DESIGNATION R20)
3PCS, 4.5V
DRY BATTERY
SIZE " D "
(IEC DESIGNATION R20)
3PCS, 4.5V
E4 MODEL
VOLTAGE SELECT
BOARD
14
1-679-964-
WHT
14
(14)
F
G
H
I
J
POWER (1) BOARD
E4,SP,AUS,AR
MODEL
WHT
RED
US,E92,MX MODEL
3
MAIN BOARD
KH321
(Page 37)
WHT
BLK
RED
BLK
RED
1-679-969-
(14)
S901
VOLTAGE
SELECTOR
220-240V
110-120V
1-682-250-
POWER (2) BOARD
T901
POWER
TRANSFORMER
1-679-970-
14
14
(14)
WHT
RED
• Semiconductor
Location
Ref. No. Location
D901 H-2
D902 H-1
D903 I-2
D904 I-1
4444
6-28. SCHEMATIC DIAGRAMS — POWER SUPPLY SECTION (NEW TYPE) — • Refer to page 22 for Common Note on Schematic Diagrams.
(Page 40)
CFD-S26
45 45
CFD-S26
• IC Block Diagrams
IC701 LC78645E (CD Board)
SLCO
1
SLCO
SLCIST
EFMIN
RFVDD
RFVSS
VREF
RFMON
JITTC
ADAVDD
ADAVSS
FIN1
FIN2
TIN1
TIN2
REFI
TEC
TDO
SLCIST
2
EFMIN
3
RF
4
RF
5
6
FIN1
7
FIN2
8
TIN1
9
TIN2
10
VREF
11
REFI
12
FE
13
FE
TE
14
15
16
17
18
19
20
TEC
TE
RFMON
JITTC
ADAVDD
ADAVSS
TDO
FIN1
FIN2
TIN1
TIN2
REFI
DEFECT
SBCK/CONT6
CONT4,5
ADAVDD
ADAVSS
JITTC
PDO1
PDO2
FR
PCKIST
VVDD
VVSS
SBCK/FG
WRQ
CL
CE
DI
DO
CONT1-3
79 78 77 76 75 74 73 72 71
LDS
LDD
+
–
+
–
+
–
+
–
LEVEL SET
A/D
SLICE LEVEL
CONTROL
PLL
VCEC
CLOCK
GENERATOR
COMMAND
INTERFACE
GENERAL PURPOSE
PORTS
8FS
DIGITAL FILTER
1BIT DAC
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38
LDS80LDD
FR
VVDD
FR
VVDD
MIX
LPF
TBAL
TBAL
RAM
SERVO PROCESSOR
JITTER
DETECT
CLV,CAV
CONTROL
16MOUT
XVSS
XIN
XOUT
XVDD
FDO
SLDO
SPDO
CONT4
GPDAC
FDO
SLDO
SPDO
CONT4
GPDAC
PCKIST
VVSS
PCKIST
VVSS
AGC
INTERPOLATION
CONT5
SBCK/CONT6
CONT5
SBCK/CONT6
PDO2
PDO1
CONT1
CONT2
CONT3
70
PDO2
PDO1
CONT1
CONT2
CONT3
FE
EQ
LPF
LPF
SW
RUPTURE DEFECT
DETECT,PROTECT,INSERT,
SUBCODE DECODE CRC
MONITOR SIGNAL SELECTOR
ERROR
CORRECTION
AUDIO CD
MUTE
ATTENUATION
DEEMPHASIS
LPF
V/P
FSEQ
MONI1
DEFECT
SBCK/FG
V/P
FSEQ
MONI1
DEFECT
SBCK/FG
VSS
VDD5V
DRF
RES
DRF
TE
SW
TRACK JUMP
D/A
MONI4
MONI5
MONI3
MONI4
MONI5
WRQDODICLCE
WRQDODICLCE
RF
TEC
+
–
RAM
EXTERNAL
AUDIO IN
SERIAL
OUT
AUDIO OUT
39 40
VDD
DOUT
(3.3V)VSS
PH
BH
S/H
TEST
69 68 67 66 65 64 63 62 61
–
+
AUTO ADJUST
DRF
FRAME SYNC
EFM DECODE
MONI2
MONI3
MONI2
MONI
CONT
APC
+
–
+
–
FDO
SPDO
SLDO
GPDAC
FSEQ
MONI1-5
V/P
RFMON
VREF
LDD
LDS
TDO
FSX/16MIN
ASDFIN
ASDACK
ASLRCK
DATACK
DRF
EFLG
DATA
LRSY
LVDD
LVSS
LCHO
RCHO
RVDD
RVSS
C2F
DATA
DATACK
LRSY
ASDFIN
ASDACK
ASLRCK
16MOUT
EFLG
C2F
XVSS
FSX/16MIN
XIN
XOUT
XVDD
RVDD
RCHO
RVSS
LVSS
LCHO
LVDD
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
DATA
DATACK
LRSY
ASDFIN
ASDACK
ASLRCK
16MOUT
EFLG
C2F
XVSS
FSX/16MIN
XIN
XOUT
XVDD
RVDD
RCHO
RVSS
LVSS
LCHO
LVDD
IC702 BA6998FP-E2 (CD Board) IC1 TA2149N (MAIN Board)
GND1
1
SP–
SP+
SPIN
RST
REG–B
REGO
MUTE
GND
TIN
(TIN)
GND
OPOUT
28
1
D.BUFF
2
D.BUFF
3
4
THERMAL
SHUT-DOWN
MONITOR
5
6
7
8
9
10
D.BUFF
T–
11
D.BUFF
T+
12
13
14
DRIVER
MUTE
LEVEL
SHIFT
REGULATOR
LEVEL
SHIFT
LEVEL
LEVEL
SHIFT
SHIFT
D.BUFF
D.BUFF
VCC
VCC
D.BUFF
D.BUFF
GND
27
SL–
SL+
26
25
SLIN
24
(SLIN)
23
VREF
VCC
22
VCC
21
20
(FIN)
FIN
19
F–
18
F+
17
NC
16
OPIN
15
FM RF-IN
AM LOW CUT
MIX OUT
VCC2
AF IF-IN
FM IF-IN
GND2
AGC
QUAD
R-OUT
L-OUT
FM RF
2
3
4
5
6
7
8
9
10
11
12
AM IF
FM IF
AGC
MUTE
FM
MIX
IC2 LC72137M-TLM (MAIN Board)
CE
1
DI
2
CCB
3
4
5
6
7
8
9
10
UNIVERSAL
COUNTER
I/F
PROGRAMMABLE
LATCH
DATA SHIFT REGISTER
12BITS
DIVIDER
UNLOCK
DETECTOR
SWALLOW
COUNTER
1/16,1/17
4BITS
REFERENCE
DIVIDER
PHASE
DETECTOR
CHARGE
PUMP
POWER ON
RESET
1/2
20
XOUT
XIN
19
18
LP-OUT
17
LP-IN
PD
16
VSS
15
14
VDD
MO/ST
13
FM IN
12
AM IN
11
CL
DO
TV-H
TV-H/WB
FM//TV-L
ST-IND
FM/AM
IF IN
AM
MIX
LEVEL
DET
AM
DET
FM
DET
ST/MO
FM/AM
24
FM RF-OUT
23
VCC1
AM RF-IN
22
FM
OSC
AM
OSC
BUFF
BUFF
IF BUFF
1/8
AF BUFF
VCO
DIVIDE
DECODE
ST
SW
IF REQ
1/1 OR
1/16
AF
21
20
19
18
17
16
15
14
13
FM OSC
AM OSC
OSC-OUT
ST-IND
IF-OUT
DET-OUT
MPX- IN
LPF2/MO-ST
LPF1/BAND
4646
CFD-S26
IC803 BR24C01AF-WE2 (MAIN Board)
1K BIT EEPROM ARRAY
SLAVE • WORD
ADDRESS
7BIT
REGISTER
START STOP
POWER SUPPLY
VOLTAGE DETECTION
GND
1
A0
7BIT
ADDRESS
A1
2
A2
3
4
DECODER
CONTROL CIRCUIT
HIGH VOLTAGE
OCCURENCE CIRCUIT
IC301 TA2068N (PRE Board)
8BIT
DATA
REGISTER
ACK
IC302 M62429P (MAIN Board)
VIN2 VOUT2 VCC CLOCK
8
8
VCC
7
WP
6
SCL
SDA
5
VR 2
VOL AMP 2
VOL AMP 1
VR 1
1
VIN1 VOUT1 GND DATA
7
REF AMP
2 3 4
VREF
6
LOGIC
CONTROL
5
AGC
L.PO
L.NF
L.RO
L.IN
REF
GND
R.IN
R.RO
R.NF
R.PO
MIC.NF
1
2
3
4
5
6
REF
AMP
7
8
9
10
11
12
REC
AMP1
2.1
NAB
AMP2
26dB
REC
AMP2
26dB
MIC
AMP1
DET
NAB
AMP1
ALC2 ALC1
ON
BUF AMP
A1
MUTE
BUF AMP
A2
TAPE
BUF AMP
BUF AMP
TAPE
TAPE
B1
B2
TAPE
LINE
RADIO
MUTE
MUTE
RADIO
LINE
ON
ON
MONITOR
AMP
MONITOR
AMP
7dB
7dB
LOGIC
24
23
22
21
20
19
18
17
16
15
14
13
L.RAD
MIC I/EX
L.LINE
REC
L.LO
VCC
R.LO
LINE
R.LINE
TAPE
R.RAD
MIC
47
CFD-S26
2
NOTE:
• The mechanical parts with no reference
number in the exploded views are not supplied.
• Items marked “*” are not stocked since
they are seldom required for routine service.
Some delay should be anticipated
when ordering these items.
• Abbreviation
AR : Argentina model
AUS : Australian model
E4 : AC 110-120V/220-240V area in E model
E92 : AC 120V area in E model
MX : Mexican model
SP : Singapore model
7-1. CABINET (FRONT) SECTION
SECTION 7
EXPLODED VIEWS
• Color Indication of Appearance Parts
Example :
KNOB, BALANCE (WHITE) ... (RED)
R
Parts Color Cabinet’s Color
• Accessories and packing materials and
hardware (# mark) list are given in
the last of this parts list.
The components identified by
mark 0 or dotted line with mark
R
0 are critical for safety.
Replace only with part number
specified.
SP301
2
#1
9
#2
#2
11
12
#1
5
5
10
5
8
5
#
#2
5
6
7
5
4
3
1
#1
#1
SP302
Ref. No. Part No. Description Remark
1 X-3380-032-1 CABINET (FRONT) SUB ASSY (S) (SILVER) (US)
1 X-3380-169-1 CABINET (FRONT) SUB ASSY (B) (BLACK) (US)
1 X-3380-170-1 CABINET (FRONT) SUB ASSY (W) (WHITE) (US)
1 X-3380-173-1 CABINET (FRONT) SUB ASSY (S) (SILVER)
(E4,E92,AUS,MX,SP,AR)
2 3-224-360-01 WINDOW (LCD) (SILVER)
2 3-224-360-21 WINDOW (LCD) (BLACK,WHITE) (US)
3 3-224-358-01 BUTTON (FUNCTION) (SILVER)
3 3-224-358-11 BUTTON (FUNCTION) (BLACK) (US)
3 3-224-358-31 BUTTON (FUNCTION) (WHITE) (US)
* 4 1-679-967-11 CONTROL (2) BOARD
5 4-951-620-11 SCREW (2.6X10), +BVTP
6 3-224-359-01 BUTTON (10 KEY)
7 3-224-356-01 BUTTON (POWER) (SILVER)
7 3-224-356-11 BUTTON (POWER) (BLACK) (US)
7 3-224-356-31 BUTTON (POWER) (WHITE) (US)
48
Ref. No. Part No. Description Remark
8 3-224-357-01 BUTTON (MODE) (SILVER)...(SILVER,WHITE)
8 3-224-357-11 BUTTON (MODE) (BLACK) (US)
* 9 1-679-968-11 CONTROL (3) BOARD
* 10 1-679-966-11 CONTROL (1) BOARD
* 11 1-757-559-11 CABLE, FLAT 8P
12 3-224-379-01 LID, BATTERY CASE (SILVER)
12 3-224-379-11 LID, BATTERY CASE (BLACK) (US)
12 3-224-379-21 LID, BATTERY CASE (WHITE) (US)
12 3-224-379-31 LID, BATTERY CASE (SILVER) (SP,AR)
SP301 1-529-723-21 SPEAKER (10cm) (L-CH)
SP302 1-529-723-21 SPEAKER (10cm) (R-CH)
(US,E4,E92,AUS,MX)
7-2. CABINET (REAR) SECTION
#1
CFD-S26
#2
#2
#2
56
#1
54
T901
#1
#1
F902
53
#1
S901
52
US, E92, MX,
AUS, SP, AR Model
60
E4 Model
55
58
57
58
57
59
51
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
51 3-224-368-01 CABINET (REAR) (SILVER) (US)
51 3-224-368-11 CABINET (REAR) (SILVER) (E92,MX)
51 3-224-368-21 CABINET (REAR) (SILVER) (AUS)
51 3-224-368-41 CABINET (REAR) (BLACK) (US)
51 3-224-368-51 CABINET (REAR) (WHITE) (US)
51 3-224-368-71 CABINET (REAR) (SILVER) (SP,AR)
51 3-227-958-11 CABINET (REAR) (SILVER) (E4)
52 3-034-633-01 COVER (VOL SEL) (US,E92,MX,AUS,SP,AR)
* 53 1-679-969-11 POWER (1) BOARD
* 54 1-679-970-11 POWER (2) BOARD
* 55 1-679-964-11 BATTERY TERMINAL (1) BOARD
56 3-224-372-01 HANDLE (SILVER)
56 3-224-372-11 HANDLE (BLACK) (US)
56 3-224-372-21 HANDLE (WHITE) (US)
57 4-960-167-01 SCREW (3X8) (DIA.10), +WH
58 3-028-154-01 TERMINAL (–), BATTERY
* 59 1-679-965-11 BATTERY TERMINAL (2) BOARD
* 60 1-682-250-14 VOLTAGE SELECT BOARD (E4)
0 F902 1-532-388-51 FUSE, TIME-LAG (T2AL/250V) (E4)
0 F902 1-533-469-11 FUSE, TIME-LAG (T2.5AL/250V) (SP,AUS,AR)
0 S901 1-552-921-00 SWITCH, POWER (VOLTAGE SELECTOR) (E4)
0 T901 1-435-921-11 TRANSFORMER, POWER (AUS,SP,AR)
0 T901 1-435-922-11 TRANSFORMER, POWER (E4)
0 T901 1-435-974-11 TRANSFORMER, POWER (US,E92,MX)
49
CFD-S26
7-3. CABINET (UPPER) SECTION
MF-V5-117
104
#3
103
110
#3
112
111
108
113
109
107
#1
105
LCD801
114
#1
106
#1
#1
128
127
129
#1
#1
130
115
131
125
S801
123
122
116
120
117
122
ANT1
118
#5
126
119
121
122
#1
KSM-213CDP
121
122
123
124
101
#1
102
132
#3
50
CFD-S26
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
* 101 A-3062-378-A MAIN BOARD, COMPLETE (SP)
* 101 A-3062-379-A MAIN BOARD, COMPLETE (E4)
* 101 A-3062-386-A MAIN BOARD, COMPLETE (AR)
* 101 A-3062-594-A MAIN BOARD, COMPLETE (E92,MX)
* 101 A-3062-614-A MAIN BOARD, COMPLETE (AUS)
* 101 A-3347-088-A MAIN BOARD, COMPLETE (US)
* 102 1-757-560-11 CABLE, FLAT 11P (CNP806)
* 103 A-3347-167-A PRE BOARD, COMPLETE
104 3-222-726-01 CHASSIS (TC)
105 3-222-727-01 LEVER (REC)
106 4-951-620-01 SCREW (2.6X8), +BVTP
107 3-224-378-01 BUTTON (PAUSE) (SILVER)
(US,E4,E92,AUS,MX)
107 3-224-378-11 BUTTON (PAUSE) (BLACK) (US)
107 3-224-378-21 BUTTON (PAUSE) (WHITE) (US)
107 3-224-378-31 BUTTON (PAUSE) (SILVER) (SP,AR)
108 3-224-377-01 BUTTON (STOP) (SILVER) (US,E4,E92,AUS,MX)
108 3-224-377-11 BUTTON (STOP) (BLACK) (US)
108 3-224-377-21 BUTTON (STOP) (WHITE) (US)
108 3-224-377-31 BUTTON (STOP) (SILVER) (SP,AR)
109 3-224-376-01 BUTTON (FF) (SILVER) (US,E4,E92,AUS,MX)
109 3-224-376-11 BUTTON (FF) (BLACK) (US)
109 3-224-376-21 BUTTON (FF) (WHITE) (US)
109 3-224-376-31 BUTTON (FF) (SILVER) (SP,AR)
110 3-224-375-01 BUTTON (REW) (SILVER) (US,E4,E92,AUS,MX)
110 3-224-375-11 BUTTON (REW) (BLACK) (US)
110 3-224-375-21 BUTTON (REW) (WHITE) (US)
110 3-224-375-31 BUTTON (REW) (SILVER) (SP,AR)
111 3-224-374-01 BUTTON (PLAY) (SILVER) (US,E4,E92,AUS,MX)
111 3-224-374-11 BUTTON (PLAY) (BLACK) (US)
111 3-224-374-21 BUTTON (PLAY) (WHITE) (US)
111 3-224-374-31 BUTTON (PLAY) (SILVER) (SP,AR)
112 3-224-373-01 BUTTON (REC) (SILVER) (US,E4,E92,AUS,MX)
112 3-224-373-11 BUTTON (REC) (BLACK) (US)
112 3-224-373-21 BUTTON (REC) (WHITE) (US)
112 3-224-373-31 BUTTON (REC) (SILVER) (SP,AR)
113 3-922-112-21 DAMPER
114 3-224-369-01 CABINET (UPPER) (SILVER)
(US,E4,E92,AUS,MX)
114 3-224-369-11 CABINET (UPPER) (BLACK) (US)
114 3-224-369-21 CABINET (UPPER) (WHITE) (US)
114 3-224-369-31 CABINET (UPPER) (SILVER) (SP,AR)
115 X-3380-033-1 HOLDER ASSY (S), CASSETTE (SILVER)
(US,E4,E92,AUS,MX)
115 X-3380-288-1 HOLDER ASSY (B), CASSETTE (BLACK) (US)
115 X-3380-289-1 HOLDER ASSY (W), CASSETTE (WHITE) (US)
115 X-3380-290-1 HOLDER ASSY (S), CASSETTE (SILVER) (SP,AR)
116 3-224-370-01 LID (CD) (SILVER) (US,E4,E92,AUS,MX)
116 3-224-370-11 LID (CD) (BLACK) (US)
116 3-224-370-21 LID (CD) (WHITE) (US)
116 3-224-370-31 LID (CD) (SILVER) (SP,AR)
116 3-224-370-41 LID (CD) (BLUE) (SP,AR)
117 1-452-899-11 MAGNET
118 3-019-395-01 PLATE, CHUCKING
119 3-224-367-01 TERMINAL, ANTENNA
120 3-923-736-01 COVER, CD
121 3-038-948-01 RUBBER, VIBRATION PROOF
122 3-921-725-11 SCREW (2.6X10), +PWH
123 3-038-948-11 RUBBER, VIBRATION PROOF
124 1-792-684-11 WIRE (FLAT TYPE) (16 CORE)
* 125 1-757-561-11 CABLE, FLAT 14P (CNP804)
126 4-951-620-11 SCREW (2.6X10), +BVTP
127 3-031-561-01 SPRING (CASSETTE)
128 3-031-560-01 SHAFT (MD)
129 4-960-167-01 SCREW (3X8) (DIA.10), +WH
130 3-922-112-41 DAMPER
131 3-031-562-01 SPRING (CD)
* 132 A-3347-089-A CD BOARD, COMPLETE
ANT1 1-501-883-21 ANTENNA, TELESCOPIC
LCD801 1-804-243-11 DISPLAY PANEL, LIQUID CRYSTAL
S801 1-692-960-11 SWITCH, PUSH (1 KEY)
(Z PUSH OPEN/CLOSE)
51
CFD-S26
7-4. TAPE MECHANISM SECTION-1
(MF-V5-117)
158
169
HE301
155
HRP301
156
157
168
159
170
160
161
162
163
164
167
165
154
153
166
151
152
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
151 3-933-010-01 SPRING (S/P), TORSION
152 3-933-025-01 SPRING (P), TORSION
153 3-040-857-01 LEVER (P)
154 3-934-024-01 ROLLER, PINCH
155 3-933-019-01 SPRING (F/R), TORSION
156 3-933-028-01 SPRING (FWD), TORSION
157 3-933-016-01 GEAR (S REEL)
158 3-008-590-01 SLIDER (REC)
159 3-008-592-01 BASE (H), HEAD
* 160 3-008-588-01 SLIDER (REW)
* 161 3-008-589-13 SLIDER (FF)
* 162 3-008-587-01 SLIDER (STOP)
* 163 3-008-591-01 SLIDER (PAUSE)
164 3-933-004-01 CLAW, REEL
* 165 3-933-021-01 SLIDER (FRP)
* 166 3-933-006-01 SLIDER (EJECT)
167 3-934-833-01 SPRING (FRP)
168 3-022-794-02 SPRING (BT)
169 3-933-007-01 PLATE, LOCK
* 170 3-012-114-01 LEVER (FR)
HE301 1-543-876-11 HEAD (ERASE)
HRP301 1-500-668-11 HEAD, MAGNETIC (RECORD/PLAYBACK)
52
7-5. TAPE MECHANISM SECTION-2
(MF-V5-117)
CFD-S26
207
206
211
M801
213
204
S802
203
208
212
219
205
216
218
209
210
217
214
#4
201
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
201 3-933-029-01 LEVER, ERASING PREVENTION
202 3-933-182-01 SPRING, CASSETTE
203 3-932-995-01 GEAR (MID)
204 X-3371-667-1 CLUTCH ASSY
205 3-932-997-01 GEAR (CAM)
* 206 3-932-999-01 SLIDER (SW)
207 3-932-998-01 SPRING (GROUND), TORSION
208 3-009-648-01 LEVER (S.OFF)
209 3-936-438-01 LEVER (K)
210 X-3373-572-1 REEL ASSY (N), T
211 3-933-020-11 BELT
202
215
212 X-3377-877-2 FLYWHEEL ASSY
213 3-932-993-01 CHASSIS, OUTSERT
214 3-343-358-01 RING, RETAINING
215 3-223-156-01 SPRING (CAM), COMPRESSION
216 3-009-650-02 SPRING (K), COMPRESSION
217 3-937-760-01 SPRING (GROUND), COMPRESSION
218 3-934-336-01 BEARING
219 3-939-383-02 SPRING, COMPRESSION
M801 A-3320-446-A MOTOR ASSY (CAPSTAN/REEL)
S802 1-762-679-11 SWITCH, LEAF (TAPE PLAY)
53
CFD-S26
Ver 1.2
7-6. OPTICAL PICK-UP SECTION
(KSM-213CDP)
251
256
not supplied
254
255
252
253
M701
M702
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
Ref. No. Part No. Description Remark
0 251 8-848-483-05 PICK-UP, OPTICAL KSS-213C/Q-RP
252 3-713-786-51 SCREW +P 2X3
253 2-626-908-01 SHAFT, SLED
254 2-627-003-01 GEAR (B) (RP)
54
Ref. No. Part No. Description Remark
255 X-2162-709-1 CHASSIS ASSY (CDP), MOTOR (SPINDLE)
(including M701)
256 2-625-188-02 GEAR (A)
M702 X-2625-769-1 GEAR ASSY (MB), MOTOR (SLED)
CFD-S26
SECTION 8
ELECTRICAL PARTS LIST
BATTERY TERMINAL (1)
BATTERY TERMINAL (2)
CD
NOTE:
• Due to standardization, replacements in
the parts list may be different from the
parts specified in the diagrams or the
components used on the set.
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
• RESISTORS
All resistors are in ohms.
METAL:Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F:nonflammable
• Abbreviation
AUS : Australian model E4 : AC 110-120V/220-240V area in E model
MX : Mexican model E92 : AC 120V area in E model
SP : Singapore model AR : Argentina model
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
* 1-679-964-11 BATTERY TERMINAL (1) BOARD (FORMER)
**************************
3-028-154-01 TERMINAL (–), BATTERY
*************************************************************
• Items marked “*” are not stocked since
they are seldom required for routine service.
Some delay should be anticipated
when ordering these items.
• SEMICONDUCTORS
In each case, u : µ, for example:
uA.. : µA.. uPA.. : µPA..
uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD..
• CAPACITORS
uF : µF
• COILS
uH : µH
C720 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C721 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C722 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C723 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C724 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
When indicating parts by reference
number, please include the board.
* 1-679-964-11 BATTERY TERMINAL (1) BOARD (NEW)
**************************
3-028-154-01 TERMINAL (–), BATTERY
*************************************************************
* 1-679-965-11 BATTERY TERMINAL (2) BOARD (FORMER)
**************************
3-028-154-01 TERMINAL (–), BATTERY
< CONNECTOR >
* CNP904 1-580-163-11 PIN, CONNECTOR (PC BOARD) 2P
*************************************************************
* 1-679-965-11 BATTERY TERMINAL (2) BOARD (NEW)
**************************
3-028-154-01 TERMINAL (–), BATTERY
< CONNECTOR >
* CNP904 1-580-163-11 PIN, CONNECTOR (PC BOARD) 2P
*************************************************************
* A-3347-089-A CD BOARD, COMPLETE (FORMER)
*******************
< CAPACITOR >
C701 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C702 1-104-664-11 ELECT 47uF 20% 10V
C703 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C704 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C705 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C725 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C726 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C727 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C728 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V
C729 1-125-837-00 CERAMIC CHIP 1uF 10% 6.3V
C730 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C731 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V
C732 1-104-665-11 ELECT 100uF 20% 10V
C733 1-104-665-11 ELECT 100uF 20% 10V
C734 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C735 1-126-916-11 ELECT 1000uF 20% 6.3V
C736 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C739 1-165-128-11 CERAMIC CHIP 0.22uF 16V
C740 1-126-935-11 ELECT 470uF 20% 10V
C741 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C742 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C743 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C744 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C745 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C746 1-104-665-11 ELECT 100uF 20% 10V
C747 1-104-665-11 ELECT 100uF 20% 10V
C750 1-104-665-11 ELECT 100uF 20% 10V
C751 1-164-156-11 CERAMIC CHIP 0.1uF 25V
< CONNECTOR >
CNP701 1-779-466-11 CONNECTOR, FFC (LIF(NON-ZIF)) 16P
* CNP702 1-784-736-11 CONNECTOR, FFC 14P
< FERRITE BEAD >
FB701 1-469-701-21 INDUCTOR, FERRITE BEAD
C706 1-126-960-11 ELECT 1uF 20% 50V
C707 1-115-156-11 CERAMIC CHIP 1uF 10V
C708 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C709 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C711 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C712 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C713 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C716 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C717 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V
< IC >
IC701 8-759-830-25 IC LC78645E
IC702 8-759-591-62 IC BA6998FP
< JUMPER RESISTOR >
JC701 1-216-864-11 METAL CHIP 0 5% 1/16W
JC702 1-216-864-11 METAL CHIP 0 5% 1/16W
JC703 1-216-864-11 METAL CHIP 0 5% 1/16W
55
CFD-S26
CD
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
JC704 1-216-813-11 METAL CHIP 220 5% 1/16W
< FERRITE BEAD >
L706 1-414-445-11 FERRITE, EMI (SMD)
< TRANSISTOR >
Q701 8-729-054-57 TRANSISTOR KTN2907AS-RTK
< RESISTOR >
R701 1-216-841-11 METAL CHIP 47K 5% 1/16W
R702 1-216-835-11 METAL CHIP 15K 5% 1/16W
R703 1-216-835-11 METAL CHIP 15K 5% 1/16W
R704 1-216-835-11 METAL CHIP 15K 5% 1/16W
R705 1-216-835-11 METAL CHIP 15K 5% 1/16W
R706 1-216-841-11 METAL CHIP 47K 5% 1/16W
R707 1-216-797-11 METAL CHIP 10 5% 1/16W
R708 1-216-833-11 METAL CHIP 10K 5% 1/16W
R709 1-216-837-11 METAL CHIP 22K 5% 1/16W
R710 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R711 1-216-815-11 METAL CHIP 330 5% 1/16W
R712 1-216-809-11 METAL CHIP 100 5% 1/16W
R714 1-216-811-11 METAL CHIP 150 5% 1/16W
R715 1-216-811-11 METAL CHIP 150 5% 1/16W
R716 1-216-821-11 METAL CHIP 1K 5% 1/16W
R717 1-216-821-11 METAL CHIP 1K 5% 1/16W
R718 1-216-821-11 METAL CHIP 1K 5% 1/16W
R719 1-216-809-11 METAL CHIP 100 5% 1/16W
R720 1-216-809-11 METAL CHIP 100 5% 1/16W
R721 1-216-821-11 METAL CHIP 1K 5% 1/16W
R722 1-216-809-11 METAL CHIP 100 5% 1/16W
R723 1-216-809-11 METAL CHIP 100 5% 1/16W
R724 1-216-841-11 METAL CHIP 47K 5% 1/16W
R725 1-216-819-11 METAL CHIP 680 5% 1/16W
R726 1-216-819-11 METAL CHIP 680 5% 1/16W
R727 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R728 1-216-833-11 METAL CHIP 10K 5% 1/16W
R729 1-216-813-11 METAL CHIP 220 5% 1/16W
R730 1-216-821-11 METAL CHIP 1K 5% 1/16W
R731 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R741 1-216-831-11 METAL CHIP 6.8K 5% 1/16W
R743 1-216-831-11 METAL CHIP 6.8K 5% 1/16W
R744 1-216-845-11 METAL CHIP 100K 5% 1/16W
< SWITCH >
S701 1-762-812-11 SWITCH, LEAF (LIMIT)
* A-3347-089-A CD BOARD, COMPLETE (NEW)
*******************
< CAPACITOR >
C701 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C702 1-104-664-11 ELECT 47uF 20% 10V
C703 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C704 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C705 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C706 1-126-960-11 ELECT 1uF 20% 50V
C707 1-115-156-11 CERAMIC CHIP 1uF 10V
C708 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C709 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C711 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C716 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C717 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V
C720 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C721 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C722 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C723 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C724 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C725 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C726 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C727 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C728 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V
C729 1-125-837-00 CERAMIC CHIP 1uF 10% 6.3V
C730 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C731 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V
C732 1-104-665-11 ELECT 100uF 20% 10V
C733 1-104-665-11 ELECT 100uF 20% 10V
C734 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C735 1-126-916-11 ELECT 1000uF 20% 6.3V
C736 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C739 1-165-128-11 CERAMIC CHIP 0.22uF 16V
C740 1-126-935-11 ELECT 470uF 20% 10V
C741 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C742 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C743 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C744 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C745 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C746 1-104-665-11 ELECT 100uF 20% 10V
C747 1-104-665-11 ELECT 100uF 20% 10V
C750 1-104-665-11 ELECT 100uF 20% 10V
C751 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C754 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C755 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
< VIBRATOR >
X701 1-795-173-11 VIBRATOR, CERAMIC (33.86MHz)
*************************************************************
56
< CONNECTOR >
CNP701 1-770-168-11 CONNECTOR, FFC/FPC 16P
* CNP702 1-784-736-11 CONNECTOR, FFC 14P
CFD-S26
CONTROL (1)CD
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
< FERRITE BEAD >
FB701 1-469-701-21 INDUCTOR, FERRITE BEAD
< IC >
IC701 8-759-830-25 IC LC78645E
IC702 8-759-591-62 IC BA6998FP
R743 1-216-831-11 METAL CHIP 6.8K 5% 1/16W
R744 1-216-845-11 METAL CHIP 100K 5% 1/16W
< SWITCH >
S701 1-762-812-11 SWITCH, LEAF (LIMIT)
< VIBRATOR >
< JUMPER RESISTOR >
JC701 1-216-864-11 METAL CHIP 0 5% 1/16W
JC702 1-216-864-11 METAL CHIP 0 5% 1/16W
JC703 1-216-864-11 METAL CHIP 0 5% 1/16W
JC704 1-216-813-11 METAL CHIP 220 5% 1/16W
< FERRITE BEAD >
L706 1-414-445-11 FERRITE, EMI (SMD)
< TRANSISTOR >
Q701 8-729-054-57 TRANSISTOR KTN2907AS-RTK
< RESISTOR >
R701 1-216-841-11 METAL CHIP 47K 5% 1/16W
R702 1-216-835-11 METAL CHIP 15K 5% 1/16W
R703 1-216-835-11 METAL CHIP 15K 5% 1/16W
R704 1-216-835-11 METAL CHIP 15K 5% 1/16W
R705 1-216-835-11 METAL CHIP 15K 5% 1/16W
R706 1-216-841-11 METAL CHIP 47K 5% 1/16W
R707 1-216-797-11 METAL CHIP 10 5% 1/16W
R708 1-216-833-11 METAL CHIP 10K 5% 1/16W
R709 1-216-837-11 METAL CHIP 22K 5% 1/16W
R710 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R711 1-216-815-11 METAL CHIP 330 5% 1/16W
R712 1-216-809-11 METAL CHIP 100 5% 1/16W
R714 1-216-811-11 METAL CHIP 150 5% 1/16W
R715 1-216-811-11 METAL CHIP 150 5% 1/16W
R716 1-216-821-11 METAL CHIP 1K 5% 1/16W
R717 1-216-821-11 METAL CHIP 1K 5% 1/16W
R718 1-216-821-11 METAL CHIP 1K 5% 1/16W
R719 1-216-809-11 METAL CHIP 100 5% 1/16W
R720 1-216-809-11 METAL CHIP 100 5% 1/16W
R721 1-216-821-11 METAL CHIP 1K 5% 1/16W
R722 1-216-809-11 METAL CHIP 100 5% 1/16W
R723 1-216-809-11 METAL CHIP 100 5% 1/16W
R724 1-216-841-11 METAL CHIP 47K 5% 1/16W
R725 1-216-819-11 METAL CHIP 680 5% 1/16W
R726 1-216-819-11 METAL CHIP 680 5% 1/16W
R727 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R728 1-216-833-11 METAL CHIP 10K 5% 1/16W
R729 1-216-813-11 METAL CHIP 220 5% 1/16W
R730 1-216-821-11 METAL CHIP 1K 5% 1/16W
R731 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R741 1-216-831-11 METAL CHIP 6.8K 5% 1/16W
X701 1-795-173-21 VIBRATOR, CERAMIC (33.86MHz)
*************************************************************
* 1-679-966-11 CONTROL (1) BOARD (FORMER)
******************
< CONNECTOR >
CNP401 1-770-516-31 CONNECTOR, FFC 8P
< JUMPER RESISTOR >
JC401 1-216-864-11 METAL CHIP 0 5% 1/16W
JC402 1-216-864-11 METAL CHIP 0 5% 1/16W
< CABLE HOLDER >
* KH402 1-565-386-11 HOLDER, CABLE 5P
* KH403 1-565-384-11 HOLDER, CABLE 3P
< RESISTOR >
R401 1-216-819-11 METAL CHIP 680 5% 1/16W
R402 1-216-815-11 METAL CHIP 330 5% 1/16W
R403 1-216-817-11 METAL CHIP 470 5% 1/16W
R404 1-216-821-11 METAL CHIP 1K 5% 1/16W
R405 1-216-823-11 METAL CHIP 1.5K 5% 1/16W
R406 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R407 1-216-831-11 METAL CHIP 6.8K 5% 1/16W
R408 1-216-835-11 METAL CHIP 15K 5% 1/16W
R413 1-216-823-11 METAL CHIP 1.5K 5% 1/16W
R417 1-216-819-11 METAL CHIP 680 5% 1/16W
R418 1-216-815-11 METAL CHIP 330 5% 1/16W
R419 1-216-817-11 METAL CHIP 470 5% 1/16W
R420 1-216-821-11 METAL CHIP 1K 5% 1/16W
R421 1-216-823-11 METAL CHIP 1.5K 5% 1/16W
R422 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R423 1-216-831-11 METAL CHIP 6.8K 5% 1/16W
R424 1-216-835-11 METAL CHIP 15K 5% 1/16W
R425 1-216-819-11 METAL CHIP 680 5% 1/16W
R426 1-216-815-11 METAL CHIP 330 5% 1/16W
R427 1-216-817-11 METAL CHIP 470 5% 1/16W
R428 1-216-821-11 METAL CHIP 1K 5% 1/16W
R429 1-216-823-11 METAL CHIP 1.5K 5% 1/16W
R430 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R431 1-216-831-11 METAL CHIP 6.8K 5% 1/16W
R432 1-216-835-11 METAL CHIP 15K 5% 1/16W
R440 1-216-815-11 METAL CHIP 330 5% 1/16W
R441 1-216-815-11 METAL CHIP 330 5% 1/16W
57
CFD-S26
CONTROL (2)CONTROL (1)
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R442 1-216-815-11 METAL CHIP 330 5% 1/16W
< SWITCH >
S401 1-786-050-21 SWITCH, KEYBOARD (POWER)
S402 1-786-050-21 SWITCH, KEYBOARD (SLEEP)
S403 1-786-050-21 SWITCH, KEYBOARD (N X)
S404 1-786-050-21 SWITCH, KEYBOARD (x)
S405 1-786-050-21 SWITCH, KEYBOARD (TUNE +, >)
S406 1-786-050-21 SWITCH, KEYBOARD (TUNE –, .)
S413 1-786-050-21 SWITCH, KEYBOARD (VOLUME –)
S414 1-786-050-21 SWITCH, KEYBOARD (VOLUME +)
S416 1-786-050-21 SWITCH, KEYBOARD (MEGA BASS)
S417 1-786-050-21 SWITCH, KEYBOARD (>10)
S418 1-786-050-21 SWITCH, KEYBOARD (0/10)
S419 1-786-050-21 SWITCH, KEYBOARD (9)
S420 1-786-050-21 SWITCH, KEYBOARD (6)
S421 1-786-050-21 SWITCH, KEYBOARD (5)
S422 1-786-050-21 SWITCH, KEYBOARD (4)
S423 1-786-050-21 SWITCH, KEYBOARD (3)
S424 1-786-050-21 SWITCH, KEYBOARD (2)
S425 1-786-050-21 SWITCH, KEYBOARD (1)
S426 1-786-050-21 SWITCH, KEYBOARD (7)
S427 1-786-050-21 SWITCH, KEYBOARD (8)
*************************************************************
* 1-679-966-11 CONTROL (1) BOARD (NEW)
******************
R421 1-216-823-11 METAL CHIP 1.5K 5% 1/16W
R422 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R423 1-216-831-11 METAL CHIP 6.8K 5% 1/16W
R424 1-216-835-11 METAL CHIP 15K 5% 1/16W
R425 1-216-819-11 METAL CHIP 680 5% 1/16W
R426 1-216-815-11 METAL CHIP 330 5% 1/16W
R427 1-216-817-11 METAL CHIP 470 5% 1/16W
R428 1-216-821-11 METAL CHIP 1K 5% 1/16W
R429 1-216-823-11 METAL CHIP 1.5K 5% 1/16W
R430 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R431 1-216-831-11 METAL CHIP 6.8K 5% 1/16W
R432 1-216-835-11 METAL CHIP 15K 5% 1/16W
R440 1-216-815-11 METAL CHIP 330 5% 1/16W
R441 1-216-815-11 METAL CHIP 330 5% 1/16W
R442 1-216-815-11 METAL CHIP 330 5% 1/16W
< SWITCH >
S401 1-786-050-21 SWITCH, KEYBOARD (POWER)
S402 1-786-050-21 SWITCH, KEYBOARD (SLEEP)
S403 1-786-050-21 SWITCH, KEYBOARD (N X)
S404 1-786-050-21 SWITCH, KEYBOARD (x)
S405 1-786-050-21 SWITCH, KEYBOARD (TUNE +, >)
S406 1-786-050-21 SWITCH, KEYBOARD (TUNE –, .)
S413 1-786-050-21 SWITCH, KEYBOARD (VOLUME –)
S414 1-786-050-21 SWITCH, KEYBOARD (VOLUME +)
S416 1-786-050-21 SWITCH, KEYBOARD (MEGA BASS)
S417 1-786-050-21 SWITCH, KEYBOARD (>10)
< CONNECTOR >
CNP401 1-770-516-31 CONNECTOR, FFC 8P
< JUMPER RESISTOR >
JC401 1-216-864-11 METAL CHIP 0 5% 1/16W
JC402 1-216-864-11 METAL CHIP 0 5% 1/16W
< CABLE HOLDER >
* KH402 1-565-386-11 HOLDER, CABLE 5P
* KH403 1-565-384-11 HOLDER, CABLE 3P
< RESISTOR >
R401 1-216-819-11 METAL CHIP 680 5% 1/16W
R402 1-216-815-11 METAL CHIP 330 5% 1/16W
R403 1-216-817-11 METAL CHIP 470 5% 1/16W
R404 1-216-821-11 METAL CHIP 1K 5% 1/16W
R405 1-216-823-11 METAL CHIP 1.5K 5% 1/16W
R406 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R407 1-216-831-11 METAL CHIP 6.8K 5% 1/16W
R408 1-216-835-11 METAL CHIP 15K 5% 1/16W
R413 1-216-823-11 METAL CHIP 1.5K 5% 1/16W
R417 1-216-819-11 METAL CHIP 680 5% 1/16W
R418 1-216-815-11 METAL CHIP 330 5% 1/16W
R419 1-216-817-11 METAL CHIP 470 5% 1/16W
R420 1-216-821-11 METAL CHIP 1K 5% 1/16W
S418 1-786-050-21 SWITCH, KEYBOARD (0/10)
S419 1-786-050-21 SWITCH, KEYBOARD (9)
S420 1-786-050-21 SWITCH, KEYBOARD (6)
S421 1-786-050-21 SWITCH, KEYBOARD (5)
S422 1-786-050-21 SWITCH, KEYBOARD (4)
S423 1-786-050-21 SWITCH, KEYBOARD (3)
S424 1-786-050-21 SWITCH, KEYBOARD (2)
S425 1-786-050-21 SWITCH, KEYBOARD (1)
S426 1-786-050-21 SWITCH, KEYBOARD (7)
S427 1-786-050-21 SWITCH, KEYBOARD (8)
*************************************************************
* 1-679-967-11 CONTROL (2) BOARD (FORMER)
******************
< CONNECTOR >
* CNP404 1-815-553-11 PIN, CONNECTOR (PC BOARD) 5P
< RESISTOR >
R409 1-216-819-11 METAL CHIP 680 5% 1/16W
R410 1-216-815-11 METAL CHIP 330 5% 1/16W
R411 1-216-817-11 METAL CHIP 470 5% 1/16W
R412 1-216-821-11 METAL CHIP 1K 5% 1/16W
R437 1-216-833-11 METAL CHIP 10K 5% 1/16W
R439 1-216-815-11 METAL CHIP 330 5% 1/16W
58
CFD-S26
CONTROL (2) CONTROL (3)
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
< SWITCH >
S407 1-786-050-21 SWITCH, KEYBOARD (CD)
S408 1-786-050-21 SWITCH, KEYBOARD (TAPE)
S409 1-786-050-21 SWITCH, KEYBOARD
(RADIO BAND•AUTO PRESET)
*************************************************************
* 1-679-967-11 CONTROL (2) BOARD (NEW)
******************
< CONNECTOR >
* CNP404 1-815-553-11 PIN, CONNECTOR (PC BOARD) 5P
< RESISTOR >
R409 1-216-819-11 METAL CHIP 680 5% 1/16W
R410 1-216-815-11 METAL CHIP 330 5% 1/16W
R411 1-216-817-11 METAL CHIP 470 5% 1/16W
R412 1-216-821-11 METAL CHIP 1K 5% 1/16W
R437 1-216-833-11 METAL CHIP 10K 5% 1/16W
R439 1-216-815-11 METAL CHIP 330 5% 1/16W
< SWITCH >
S407 1-786-050-21 SWITCH, KEYBOARD (CD)
S408 1-786-050-21 SWITCH, KEYBOARD (TAPE)
S409 1-786-050-21 SWITCH, KEYBOARD
(RADIO BAND•AUTO PRESET)
*************************************************************
* 1-679-968-11 CONTROL (3) BOARD (FORMER)
******************
< DIODE >
D451 8-719-059-97 LED L-34HD (OPR/BATT)
< CABLE HOLDER >
* KH405 1-565-384-11 HOLDER, CABLE 3P
< RESISTOR >
R414 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R415 1-216-831-11 METAL CHIP 6.8K 5% 1/16W
R416 1-216-835-11 METAL CHIP 15K 5% 1/16W
R434 1-216-817-11 METAL CHIP 470 5% 1/16W
R435 1-216-813-11 METAL CHIP 220 5% 1/16W
* 1-679-968-11 CONTROL (3) BOARD (NEW)
******************
< DIODE >
D451 8-719-059-97 LED L-34HD (OPR/BATT)
< CABLE HOLDER >
* KH405 1-565-384-11 HOLDER, CABLE 3P
< RESISTOR >
R414 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R415 1-216-831-11 METAL CHIP 6.8K 5% 1/16W
R416 1-216-835-11 METAL CHIP 15K 5% 1/16W
R434 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R435 1-216-813-11 METAL CHIP 220 5% 1/16W
R436 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R443 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R444 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R445 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
< SWITCH >
S411 1-786-050-21 SWITCH, KEYBOARD (DISPLAY ENT•MEMORY)
S412 1-786-050-21 SWITCH, KEYBOARD (MODE)
*************************************************************
* A-3062-378-A MAIN BOARD, COMPLETE (SP) (FORMER)
* A-3347-088-A MAIN BOARD, COMPLETE (US,E92,AUS)
*********************
7-685-647-79 SCREW +BVTP 3X10 TYPE2 N-S
< CAPACITOR >
C1 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
C4 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C7 1-162-910-11 CERAMIC CHIP 5PF 0.25PF 50V
C8 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C9 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V
C10 1-115-871-11 ELECT 1uF 20% 50V
C11 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C12 1-126-794-11 ELECT 4.7uF 20% 50V
C14 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V (SP)
C14 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
MAIN
(FORMER)
(US,E92,AUS)
R436 1-216-811-11 METAL CHIP 150 5% 1/16W
< SWITCH >
S411 1-786-050-21 SWITCH, KEYBOARD (DISPLAY ENT•MEMORY)
S412 1-786-050-21 SWITCH, KEYBOARD (MODE)
*************************************************************
C15 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V (SP)
C15 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
(US,E92,AUS)
C16 1-115-871-11 ELECT 1uF 20% 50V
C17 1-115-871-11 ELECT 1uF 20% 50V
C18 1-126-176-11 ELECT 220uF 20% 10V
C20 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C21 1-115-871-11 ELECT 1uF 20% 50V
C22 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C23 1-115-871-11 ELECT 1uF 20% 50V
59
CFD-S26
MAIN
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C24 1-162-960-11 CERAMIC CHIP 220PF 10% 50V
C26 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C27 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C29 1-126-382-11 ELECT 100uF 20% 10V
C30 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C224 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V (SP)
C225 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C226 1-126-959-11 ELECT 0.47uF 20% 50V
C228 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C229 1-104-664-11 ELECT 47uF 20% 10V
C31 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C32 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C33 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C34 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C35 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C37 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C39 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C41 1-164-230-11 CERAMIC CHIP 220PF 5% 50V
C42 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C43 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C47 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V
C49 1-161-051-00 CERAMIC 0.01uF 10% 50V
C51 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C52 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V
C53 1-136-169-00 FILM 0.22uF 5% 50V
C54 1-126-176-11 ELECT 220uF 20% 10V
C55 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C56 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C57 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C59 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C60 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C61 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C62 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C63 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C65 1-126-794-11 ELECT 4.7uF 20% 50V
C230 1-104-665-11 ELECT 100uF 20% 10V
C231 1-126-926-11 ELECT 1000uF 20% 10V
C232 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C233 1-126-963-11 ELECT 4.7uF 20% 50V
C234 1-126-963-11 ELECT 4.7uF 20% 50V
C271 1-126-964-11 ELECT 10uF 20% 50V
C303 1-126-933-11 ELECT 100uF 20% 16V
C321 1-126-935-11 ELECT 470uF 20% 10V
C322 1-104-664-11 ELECT 47uF 20% 10V
C323 1-126-964-11 ELECT 10uF 20% 50V
C324 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C325 1-126-937-11 ELECT 4700uF 20% 16V
C326 1-126-934-11 ELECT 220uF 20% 16V
C329 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C331 1-104-664-11 ELECT 47uF 20% 10V
C801 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C802 1-104-665-11 ELECT 100uF 20% 10V
C803 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C804 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V
C805 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C806 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C807 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C808 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C809 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C810 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C66 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C68 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C77 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V (SP)
C78 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V (SP)
C80 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C95 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C122 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C124 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
(US,E92,AUS)
C124 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V (SP)
C125 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C126 1-126-959-11 ELECT 0.47uF 20% 50V
C128 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C129 1-104-664-11 ELECT 47uF 20% 10V
C130 1-104-665-11 ELECT 100uF 20% 10V
C131 1-126-926-11 ELECT 1000uF 20% 10V
C132 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C133 1-126-963-11 ELECT 4.7uF 20% 50V
C134 1-126-963-11 ELECT 4.7uF 20% 50V
C171 1-126-964-11 ELECT 10uF 20% 50V
C222 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C224 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
(US,E92,AUS)
C812 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C813 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C814 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V
C815 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V
C816 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C817 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C818 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C819 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C820 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C821 1-126-960-11 ELECT 1uF 20% 50V
C822 1-126-934-11 ELECT 220uF 20% 10V
C824 1-126-960-11 ELECT 1uF 20% 50V
C830 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C831 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C832 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C833 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C834 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C835 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C836 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C837 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C838 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C951 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C952 1-162-974-11 CERAMIC CHIP 0.01uF 50V
60
CFD-S26
MAIN
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C953 1-126-935-11 ELECT 470uF 20% 10V
C957 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C959 1-104-665-11 ELECT 100uF 20% 10V
C960 1-162-974-11 CERAMIC CHIP 0.01uF 50V
< FILTER >
CF2 1-760-736-61 FILTER, CERAMIC
CF4 1-781-962-21 FILTER, CERAMIC
< CONNECTOR >
* CNP302 1-815-552-11 PIN, CONNECTOR (PC BOARD) 4P
* CNP323 1-815-445-11 PIN, CONNECTOR 4P
* CNP804 1-784-736-11 CONNECTOR, FFC 14P
CNP805 1-691-040-31 CONNECTOR, FFC 8P
CNP806 1-784-733-11 CONNECTOR, FFC 11P
< TRIMMER >
JC1 1-216-864-11 METAL CHIP 0 5% 1/16W
JC2 1-216-864-11 METAL CHIP 0 5% 1/16W
JC3 1-216-864-11 METAL CHIP 0 5% 1/16W
JC4 1-216-864-11 METAL CHIP 0 5% 1/16W
JC5 1-216-864-11 METAL CHIP 0 5% 1/16W
JC6 1-216-864-11 METAL CHIP 0 5% 1/16W
JC11 1-216-864-11 METAL CHIP 0 5% 1/16W
JC12 1-216-864-11 METAL CHIP 0 5% 1/16W
JC23 1-216-864-11 METAL CHIP 0 5% 1/16W
JC24 1-216-864-11 METAL CHIP 0 5% 1/16W
JC302 1-216-864-11 METAL CHIP 0 5% 1/16W
JC303 1-216-864-11 METAL CHIP 0 5% 1/16W
JC304 1-216-864-11 METAL CHIP 0 5% 1/16W
JC306 1-216-864-11 METAL CHIP 0 5% 1/16W
JC307 1-216-864-11 METAL CHIP 0 5% 1/16W
< JUMPER RESISTOR >
CT1 1-141-603-21 CAP, ADJ 20PF
CT3 1-141-601-21 CAP, ADJ 10PF
< DIODE >
D1 8-719-078-48 DIODE KV1471ETR1-3
D2 8-719-078-48 DIODE KV1471ETR1-3
D3 8-719-050-69 DIODE KV1520N
D10 8-719-988-61 DIODE 1SS355TE-17
D11 8-719-988-61 DIODE 1SS355TE-17
D322 8-719-988-61 DIODE 1SS355TE-17
D323 8-719-988-61 DIODE 1SS355TE-17
D324 8-719-988-61 DIODE 1SS355TE-17
D802 8-719-082-07 DIODE KDS121-RTK
D803 8-719-082-07 DIODE KDS121-RTK
D806 8-719-988-61 DIODE 1SS355TE-17
D807 8-719-083-93 DIODE KDS120-RTK
D951 8-719-988-61 DIODE 1SS355TE-17 (SP)
D952 8-719-988-61 DIODE 1SS355TE-17 (SP)
D953 8-719-084-00 DIODE KDZ7.5V-RTK
D957 8-719-082-09 DIODE KDZ3.9V-RTK
< IC >
IC1 8-759-662-67 IC TA2149N
IC2 8-759-483-40 IC LC72137M-TLM
IC302 8-759-539-45 IC M62429P
IC304 8-759-426-51 IC BA5417
IC801 8-759-658-46 IC S-81233SGY-Z
IC802 8-759-712-09 IC uPD789477-907
IC803 8-759-487-03 IC BR24C01AF-WE2
IC804 8-759-645-87 IC PST9128-T
< JACK >
J321 1-815-325-11 JACK (i)
JC308 1-216-864-11 METAL CHIP 0 5% 1/16W
JC556 1-216-864-11 METAL CHIP 0 5% 1/16W
(US,E92,AUS)
< CABLE HOLDER >
* KH321 1-565-385-11 HOLDER, CABLE 4P
* KH803 1-573-287-11 HOLDER, CABLE 2P
< COIL >
L1 1-409-775-21 COIL, AIR-CORE
L2 1-416-509-11 COIL, AIR-CORE
L3 1-424-708-11 ANTENNA, FERRITE-ROD (AM)
L4 1-411-234-21 COIL, AM OSC
L21 1-410-509-11 INDUCTOR 10uH
L801 1-414-137-31 INDUCTOR 0.22uH
L802 1-410-521-11 INDUCTOR 100uH
< LIQUID CRYSTAL DISPLAY >
LCD801 1-804-243-11 DISPLAY PANEL, LIQUID CRYSTAL
< TRANSISTOR >
Q122 8-729-054-58 TRANSISTOR KTC4075-RTK
Q124 8-729-054-24 TRANSISTOR KRC410-RTK
Q125 8-729-054-58 TRANSISTOR KTC4075-RTK
Q222 8-729-054-58 TRANSISTOR KTC4075-RTK
Q224 8-729-054-24 TRANSISTOR KRC410-RTK
Q225 8-729-054-58 TRANSISTOR KTC4075-RTK
Q801 8-729-054-21 TRANSISTOR KRC407-RTK
Q804 8-729-054-07 TRANSISTOR KRA307-RTK
Q806 8-729-054-07 TRANSISTOR KRA307-RTK
Q807 8-729-212-02 TRANSISTOR 2SC2120-Y
Q808 8-729-054-21 TRANSISTOR KRC407-RTK
Q812 8-729-054-14 TRANSISTOR KRA314-RTK
Q813 8-729-054-21 TRANSISTOR KRC407-RTK
Q814 8-729-054-21 TRANSISTOR KRC407-RTK
Q817 8-729-055-41 TRANSISTOR KTB1241Y-AT
61
CFD-S26
MAIN
Ref. No. Part No. Description Remark
Q818 8-729-054-21 TRANSISTOR KRC407-RTK
Q819 8-729-054-18 TRANSISTOR KRC404-RTK
Q820 8-729-054-23 TRANSISTOR KRC409-RTK
Q951 8-729-054-15 TRANSISTOR KRC401-RTK (SP)
Q952 8-729-040-76 TRANSISTOR KTA1273-Y-AT
Q953 8-729-054-15 TRANSISTOR KRC401-RTK
Q955 8-729-021-82 TRANSISTOR 2SD2396K
Q957 8-729-212-02 TRANSISTOR 2SC2120-Y
< RESISTOR >
R1 1-216-815-11 METAL CHIP 330 5% 1/16W
R2 1-216-817-11 METAL CHIP 470 5% 1/16W
R3 1-216-833-11 METAL CHIP 10K 5% 1/16W
R4 1-216-833-11 METAL CHIP 10K 5% 1/16W
R10 1-216-805-11 METAL CHIP 47 5% 1/16W
R11 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R13 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R24 1-216-813-11 METAL CHIP 220 5% 1/16W
R30 1-216-835-11 METAL CHIP 15K 5% 1/16W
R31 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R32 1-216-845-11 METAL CHIP 100K 5% 1/16W
R33 1-216-801-11 METAL CHIP 22 5% 1/16W
R40 1-216-849-11 METAL CHIP 220K 5% 1/16W
R41 1-216-833-11 METAL CHIP 10K 5% 1/16W
R50 1-216-821-11 METAL CHIP 1K 5% 1/16W
R51 1-216-833-11 METAL CHIP 10K 5% 1/16W
R52 1-216-864-11 METAL CHIP 0 5% 1/16W
R53 1-216-835-11 METAL CHIP 15K 5% 1/16W
R54 1-216-817-11 METAL CHIP 470 5% 1/16W
R56 1-216-815-11 METAL CHIP 330 5% 1/16W
R58 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R59 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R60 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R61 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R63 1-216-833-11 METAL CHIP 10K 5% 1/16W
R65 1-216-833-11 METAL CHIP 10K 5% 1/16W
R91 1-216-821-11 METAL CHIP 1K 5% 1/16W
R92 1-216-821-11 METAL CHIP 1K 5% 1/16W
R94 1-216-821-11 METAL CHIP 1K 5% 1/16W
R125 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R126 1-216-821-11 METAL CHIP 1K 5% 1/16W
(SP)
R126 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
(US,E92,AUS)
R127 1-216-833-11 METAL CHIP 10K 5% 1/16W
R128 1-216-819-11 METAL CHIP 680 5% 1/16W
R130 1-216-811-11 METAL CHIP 150 5% 1/16W
R131 1-216-841-11 METAL CHIP 47K 5% 1/16W
R132 1-216-809-11 METAL CHIP 100 5% 1/16W
R140 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R141 1-216-831-11 METAL CHIP 6.8K 5% 1/16W
R142 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R143 1-216-853-11 METAL CHIP 470K 5% 1/16W
Ref. No. Part No. Description Remark
R144 1-216-789-11 METAL CHIP 2.2 5% 1/16W
R145 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R225 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R226 1-216-821-11 METAL CHIP 1K 5% 1/16W
(SP)
R226 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
(US,E92,AUS)
R227 1-216-833-11 METAL CHIP 10K 5% 1/16W
R228 1-216-819-11 METAL CHIP 680 5% 1/16W
R230 1-216-811-11 METAL CHIP 150 5% 1/16W
R231 1-216-841-11 METAL CHIP 47K 5% 1/16W
R232 1-216-809-11 METAL CHIP 100 5% 1/16W
R240 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R241 1-216-831-11 METAL CHIP 6.8K 5% 1/16W
R242 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R243 1-216-853-11 METAL CHIP 470K 5% 1/16W
R244 1-216-789-11 METAL CHIP 2.2 5% 1/16W
R245 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R306 1-216-833-11 METAL CHIP 10K 5% 1/16W
R321 1-216-813-11 METAL CHIP 220 5% 1/16W
R322 1-216-833-11 METAL CHIP 10K 5% 1/16W
R323 1-216-857-11 METAL CHIP 1M 5% 1/16W
R324 1-216-845-11 METAL CHIP 100K 5% 1/16W
R325 1-216-817-11 METAL CHIP 470 5% 1/16W
R331 1-216-809-11 METAL CHIP 100 5% 1/16W
R332 1-216-809-11 METAL CHIP 100 5% 1/16W
R333 1-216-833-11 METAL CHIP 10K 5% 1/16W
R382 1-216-821-11 METAL CHIP 1K 5% 1/16W
R802 1-216-841-11 METAL CHIP 47K 5% 1/16W
R803 1-216-841-11 METAL CHIP 47K 5% 1/16W
R804 1-216-833-11 METAL CHIP 10K 5% 1/16W
R805 1-216-833-11 METAL CHIP 10K 5% 1/16W
R807 1-216-833-11 METAL CHIP 10K 5% 1/16W
R809 1-216-833-11 METAL CHIP 10K 5% 1/16W
R814 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R815 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R816 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R820 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
(SP)
R820 1-216-864-11 METAL CHIP 0 5% 1/16W
(US,E92,AUS)
R821 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
(SP)
R822 1-216-835-11 METAL CHIP 15K 5% 1/16W
(SP)
R824 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R825 1-216-821-11 METAL CHIP 1K 5% 1/16W
R827 1-216-821-11 METAL CHIP 1K 5% 1/16W
R828 1-216-809-11 METAL CHIP 100 5% 1/16W
R829 1-216-821-11 METAL CHIP 1K 5% 1/16W
R830 1-216-821-11 METAL CHIP 1K 5% 1/16W
R831 1-216-821-11 METAL CHIP 1K 5% 1/16W
R832 1-216-841-11 METAL CHIP 47K 5% 1/16W
R833 1-216-821-11 METAL CHIP 1K 5% 1/16W
62
CFD-S26
MAIN
Ref. No. Part No. Description Remark
R835 1-216-841-11 METAL CHIP 47K 5% 1/16W
R836 1-216-841-11 METAL CHIP 47K 5% 1/16W
R837 1-216-809-11 METAL CHIP 100 5% 1/16W
R838 1-216-821-11 METAL CHIP 1K 5% 1/16W
R840 1-216-821-11 METAL CHIP 1K 5% 1/16W
R841 1-216-821-11 METAL CHIP 1K 5% 1/16W
R842 1-216-821-11 METAL CHIP 1K 5% 1/16W
R843 1-216-821-11 METAL CHIP 1K 5% 1/16W
R844 1-216-835-11 METAL CHIP 15K 5% 1/16W
R845 1-216-841-11 METAL CHIP 47K 5% 1/16W
R846 1-216-821-11 METAL CHIP 1K 5% 1/16W
R847 1-216-821-11 METAL CHIP 1K 5% 1/16W
R848 1-216-809-11 METAL CHIP 100 5% 1/16W
R849 1-216-841-11 METAL CHIP 47K 5% 1/16W
R850 1-216-821-11 METAL CHIP 1K 5% 1/16W
R854 1-216-841-11 METAL CHIP 47K 5% 1/16W
R859 1-216-821-11 METAL CHIP 1K 5% 1/16W
R860 1-216-841-11 METAL CHIP 47K 5% 1/16W
R861 1-216-821-11 METAL CHIP 1K 5% 1/16W
R862 1-216-821-11 METAL CHIP 1K 5% 1/16W
R865 1-216-841-11 METAL CHIP 47K 5% 1/16W
R866 1-216-845-11 METAL CHIP 100K 5% 1/16W
R867 1-216-819-11 METAL CHIP 680 5% 1/16W
R868 1-216-819-11 METAL CHIP 680 5% 1/16W
R869 1-216-819-11 METAL CHIP 680 5% 1/16W
R870 1-216-819-11 METAL CHIP 680 5% 1/16W
R876 1-216-817-11 METAL CHIP 470 5% 1/16W
R951 1-216-841-11 METAL CHIP 47K 5% 1/16W
R952 1-216-821-11 METAL CHIP 1K 5% 1/16W
R954 1-216-821-11 METAL CHIP 1K 5% 1/16W
R955 1-216-821-11 METAL CHIP 1K 5% 1/16W
R958 1-216-815-11 METAL CHIP 330 5% 1/16W
R960 1-216-864-11 METAL CHIP 0 5% 1/16W
< TRANSFORMER >
T1 1-433-741-11 TRANSFORMER, IF
T2 1-419-465-11 COIL (DET)
< VIBRATOR >
X1 1-760-130-11 VIBRATOR, CRYSTAL (75kHz)
X801 1-795-267-11 VIBRATOR, CRYSTAL (32.768kHz)
X802 1-781-775-21 VIBRATOR, CERAMIC (4.19MHz)
*************************************************************
Ref. No. Part No. Description Remark
* A-3062-378-A MAIN BOARD, COMPLETE (SP) (NEW)
* A-3062-379-A MAIN BOARD, COMPLETE (E4) (NEW)
* A-3062-386-A MAIN BOARD, COMPLETE (AR) (NEW)
* A-3062-594-A MAIN BOARD, COMPLETE (E92,MX) (NEW)
* A-3062-614-A MAIN BOARD, COMPLETE (AUS) (NEW)
* A-3347-088-A MAIN BOARD, COMPLETE (US) (NEW)
*********************
* 1-757-560-11 CABLE, FLAT 11P (CNP806)
* 1-757-561-11 CABLE, FLAT 14P (CNP804)
7-685-647-79 SCREW +BVTP 3X10 TYPE2 N-S
< CAPACITOR >
C1 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
C4 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C7 1-162-910-11 CERAMIC CHIP 5PF 0.25PF 50V
C8 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C9 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V
C10 1-115-871-11 ELECT 1uF 20% 50V
C11 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C12 1-126-794-11 ELECT 4.7uF 20% 50V
C14 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
(E4,AUS,SP,AR)
C14 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
(US,E92,MX)
C15 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
(E4,AUS,SP,AR)
C15 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
(US,E92,MX)
C16 1-115-871-11 ELECT 1uF 20% 50V
C17 1-115-871-11 ELECT 1uF 20% 50V
C18 1-126-176-11 ELECT 220uF 20% 10V
C20 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C21 1-115-871-11 ELECT 1uF 20% 50V
C22 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C23 1-115-871-11 ELECT 1uF 20% 50V
C24 1-162-960-11 CERAMIC CHIP 220PF 10% 50V
C26 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C27 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C29 1-126-382-11 ELECT 100uF 20% 10V
C30 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C31 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C32 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C33 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C34 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C35 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C37 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C39 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C41 1-164-230-11 CERAMIC CHIP 220PF 5% 50V
C42 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C43 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C47 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V
C49 1-161-051-00 CERAMIC 0.01uF 10% 50V
C51 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
63
CFD-S26
MAIN
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C52 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V
C53 1-136-169-00 FILM 0.22uF 5% 50V
C54 1-126-176-11 ELECT 220uF 20% 10V
C55 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C56 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C271 1-126-964-11 ELECT 10uF 20% 50V
C303 1-126-933-11 ELECT 100uF 20% 16V (US)
C321 1-126-935-11 ELECT 470uF 20% 10V
C322 1-104-664-11 ELECT 47uF 20% 10V
C323 1-126-964-11 ELECT 10uF 20% 50V
C57 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C59 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C60 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C61 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C62 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C63 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C65 1-126-794-11 ELECT 4.7uF 20% 50V
C66 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C68 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C77 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
(E4,AUS,SP,AR)
C78 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
(E4,AUS,SP,AR)
C80 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C95 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C122 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C124 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
(US,AUS)
C124 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
(E4,E92,MX,SP,AR)
C125 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C126 1-126-959-11 ELECT 0.47uF 20% 50V
(E4,E92,MX,SP,AR)
C126 1-126-960-11 ELECT 1uF 20% 50V
(US,AUS)
C128 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C324 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C325 1-126-937-11 ELECT 4700uF 20% 16V
C326 1-126-934-11 ELECT 220uF 20% 16V
C329 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C331 1-104-664-11 ELECT 47uF 20% 10V
C801 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C802 1-104-665-11 ELECT 100uF 20% 10V
C803 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C804 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V
C805 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C806 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C807 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C808 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C809 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C810 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C812 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C813 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C814 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V
C815 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V
C816 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C817 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C818 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C819 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C820 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C821 1-126-960-11 ELECT 1uF 20% 50V
C129 1-104-664-11 ELECT 47uF 20% 10V
C130 1-104-665-11 ELECT 100uF 20% 10V
C131 1-126-926-11 ELECT 1000uF 20% 10V
C132 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C133 1-126-963-11 ELECT 4.7uF 20% 50V
C134 1-126-963-11 ELECT 4.7uF 20% 50V
C171 1-126-964-11 ELECT 10uF 20% 50V
C222 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C224 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
(US,AUS)
C224 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
(E4,E92,MX,SP,AR)
C225 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C226 1-126-959-11 ELECT 0.47uF 20% 50V
(E4,E92,MX,SP,AR)
C226 1-126-960-11 ELECT 1uF 20% 50V
(US,AUS)
C228 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C229 1-104-664-11 ELECT 47uF 20% 10V
C230 1-104-665-11 ELECT 100uF 20% 10V
C231 1-126-926-11 ELECT 1000uF 20% 10V
C232 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C233 1-126-963-11 ELECT 4.7uF 20% 50V
C234 1-126-963-11 ELECT 4.7uF 20% 50V
C822 1-126-934-11 ELECT 220uF 20% 10V
C824 1-126-960-11 ELECT 1uF 20% 50V
C830 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C831 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C832 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C833 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C834 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C835 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C836 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C837 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C838 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C951 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C952 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C953 1-126-935-11 ELECT 470uF 20% 10V
C957 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C959 1-104-665-11 ELECT 100uF 20% 10V
C960 1-164-156-11 CERAMIC CHIP 0.1uF 25V
< FILTER >
CF2 1-760-023-11 FILTER, CERAMIC
CF4 1-781-962-21 FILTER, CERAMIC
64
CFD-S26
MAIN
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
< CONNECTOR >
* CNP302 1-815-552-11 PIN, CONNECTOR (PC BOARD) 4P
* CNP323 1-815-445-11 PIN, CONNECTOR 4P
CNP805 1-691-040-31 CONNECTOR, FFC 8P
JC6 1-216-864-11 METAL CHIP 0 5% 1/16W
JC11 1-216-864-11 METAL CHIP 0 5% 1/16W
JC12 1-216-864-11 METAL CHIP 0 5% 1/16W
JC13 1-216-864-11 METAL CHIP 0 5% 1/16W
JC24 1-216-864-11 METAL CHIP 0 5% 1/16W
< TRIMMER >
CT1 1-141-603-21 CAP, ADJ 20PF
CT3 1-141-601-21 CAP, ADJ 10PF
< DIODE >
D1 8-719-078-48 DIODE KV1471ETR1-3
D2 8-719-078-48 DIODE KV1471ETR1-3
D3 8-719-050-69 DIODE KV1520N
D10 8-719-988-61 DIODE 1SS355TE-17
D11 8-719-988-61 DIODE 1SS355TE-17
D322 8-719-988-61 DIODE 1SS355TE-17
D323 8-719-988-61 DIODE 1SS355TE-17
D324 8-719-988-61 DIODE 1SS355TE-17
D802 8-719-082-07 DIODE KDS121-RTK
D803 8-719-082-07 DIODE KDS121-RTK
D806 8-719-988-61 DIODE 1SS355TE-17
D807 8-719-083-93 DIODE KDS120-RTK
D951 8-719-988-61 DIODE 1SS355TE-17 (E4,E92,MX,AUS,SP,AR)
D952 8-719-988-61 DIODE 1SS355TE-17 (E4,E92,MX,AUS,SP,AR)
D953 8-719-084-00 DIODE KDZ7.5V-RTK
D957 8-719-082-09 DIODE KDZ3.9V-RTK
< IC >
JC302 1-216-864-11 METAL CHIP 0 5% 1/16W
JC303 1-216-864-11 METAL CHIP 0 5% 1/16W
JC304 1-216-864-11 METAL CHIP 0 5% 1/16W
JC306 1-216-864-11 METAL CHIP 0 5% 1/16W
JC307 1-216-864-11 METAL CHIP 0 5% 1/16W
JC556 1-216-864-11 METAL CHIP 0 5% 1/16W
(US)
< CABLE HOLDER >
* KH321 1-565-385-11 HOLDER, CABLE 4P
* KH803 1-573-287-11 HOLDER, CABLE 2P
< COIL >
L1 1-409-775-21 COIL, AIR-CORE
L2 1-416-509-11 COIL, AIR-CORE
L3 1-424-708-11 ANTENNA, FERRITE-ROD (AM)
L4 1-411-234-21 COIL, AM OSC
L21 1-410-509-11 INDUCTOR 10uH
L801 1-414-137-31 INDUCTOR 0.22uH
L802 1-410-521-11 INDUCTOR 100uH
< LIQUID CRYSTAL DISPLAY >
LCD801 1-804-243-11 DISPLAY PANEL, LIQUID CRYSTAL
IC1 8-759-662-67 IC TA2149N
IC2 8-759-483-40 IC LC72137M-TLM
IC302 8-759-539-45 IC M62429P
IC304 8-759-426-51 IC BA5417
IC801 8-759-658-46 IC S-81233SGY-Z
IC802 6-700-456-01 IC uPD789477-A05-8BT
IC803 8-759-487-03 IC BR24C01AF-WE2
IC804 8-759-645-87 IC PST9128-T
< IC LINK >
ICP301 1-216-864-11 METAL CHIP 0 5% 1/16W
0 ICP301 1-533-674-11 LINK, CHIP IC (ICP-S0.5) 0.5A
(E4,E92,MX,AUS,SP,AR)
< JACK >
J321 1-815-325-11 JACK (i)
< JUMPER RESISTOR >
JC1 1-216-864-11 METAL CHIP 0 5% 1/16W
JC2 1-216-864-11 METAL CHIP 0 5% 1/16W
JC3 1-216-864-11 METAL CHIP 0 5% 1/16W
JC4 1-216-864-11 METAL CHIP 0 5% 1/16W
JC5 1-216-864-11 METAL CHIP 0 5% 1/16W
< TRANSISTOR >
Q122 8-729-054-58 TRANSISTOR KTC4075-RTK
Q124 8-729-054-24 TRANSISTOR KRC410-RTK
Q125 8-729-054-58 TRANSISTOR KTC4075-RTK
Q222 8-729-054-58 TRANSISTOR KTC4075-RTK
Q224 8-729-054-24 TRANSISTOR KRC410-RTK
Q225 8-729-054-58 TRANSISTOR KTC4075-RTK
Q801 8-729-054-21 TRANSISTOR KRC407-RTK
Q804 8-729-054-07 TRANSISTOR KRA307-RTK
Q806 8-729-054-07 TRANSISTOR KRA307-RTK
Q807 8-729-212-02 TRANSISTOR 2SC2120-Y
(US)
Q808 8-729-054-21 TRANSISTOR KRC407-RTK
Q812 8-729-054-14 TRANSISTOR KRA314-RTK
Q813 8-729-054-21 TRANSISTOR KRC407-RTK
Q814 8-729-054-21 TRANSISTOR KRC407-RTK
Q817 8-729-055-41 TRANSISTOR KTB1241Y-AT
Q818 8-729-054-21 TRANSISTOR KRC407-RTK
Q819 8-729-054-18 TRANSISTOR KRC404-RTK
Q820 8-729-054-23 TRANSISTOR KRC409-RTK
Q951 8-729-054-15 TRANSISTOR KRC401-RTK
(E4,E92,MX,AUS,SP,AR)
Q952 8-729-040-76 TRANSISTOR KTA1273-Y-AT
Q953 8-729-054-15 TRANSISTOR KRC401-RTK
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
65
CFD-S26
MAIN
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
Q955 8-729-021-82 TRANSISTOR 2SD2396K
Q957 8-729-212-02 TRANSISTOR 2SC2120-Y
< RESISTOR >
R1 1-216-815-11 METAL CHIP 330 5% 1/16W
R2 1-216-817-11 METAL CHIP 470 5% 1/16W
R3 1-216-833-11 METAL CHIP 10K 5% 1/16W
R4 1-216-833-11 METAL CHIP 10K 5% 1/16W
R10 1-216-805-11 METAL CHIP 47 5% 1/16W
R11 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R13 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R24 1-216-813-11 METAL CHIP 220 5% 1/16W
R30 1-216-835-11 METAL CHIP 15K 5% 1/16W
R31 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R32 1-216-845-11 METAL CHIP 100K 5% 1/16W
R33 1-216-801-11 METAL CHIP 22 5% 1/16W
(US,E92,MX)
R33 1-216-864-11 METAL CHIP 0 5% 1/16W
(E4,AUS,SP,AR)
R40 1-216-849-11 METAL CHIP 220K 5% 1/16W
R41 1-216-833-11 METAL CHIP 10K 5% 1/16W
R50 1-216-821-11 METAL CHIP 1K 5% 1/16W
R51 1-216-833-11 METAL CHIP 10K 5% 1/16W
R52 1-216-864-11 METAL CHIP 0 5% 1/16W
R53 1-216-835-11 METAL CHIP 15K 5% 1/16W
R54 1-216-817-11 METAL CHIP 470 5% 1/16W
R56 1-216-815-11 METAL CHIP 330 5% 1/16W
R58 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R59 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R60 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R61 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R63 1-216-833-11 METAL CHIP 10K 5% 1/16W
R65 1-216-833-11 METAL CHIP 10K 5% 1/16W
R91 1-216-815-11 METAL CHIP 330 5% 1/16W
R92 1-216-815-11 METAL CHIP 330 5% 1/16W
R94 1-216-821-11 METAL CHIP 1K 5% 1/16W
R125 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R126 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
(US,AUS)
R126 1-216-864-11 METAL CHIP 0 5% 1/16W
(E4,E92,MX,SP,AR)
R127 1-216-833-11 METAL CHIP 10K 5% 1/16W
R128 1-216-817-11 METAL CHIP 470 5% 1/16W
(E4,E92,MX,SP,AR)
R128 1-216-819-11 METAL CHIP 680 5% 1/16W
(US,AUS)
R130 1-216-811-11 METAL CHIP 150 5% 1/16W
R131 1-216-839-11 METAL CHIP 33K 5% 1/16W
(E4,E92,MX,SP,AR)
R131 1-216-841-11 METAL CHIP 47K 5% 1/16W
(US,AUS)
R132 1-216-809-11 METAL CHIP 100 5% 1/16W
R140 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R141 1-216-831-11 METAL CHIP 6.8K 5% 1/16W
R142 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R143 1-216-853-11 METAL CHIP 470K 5% 1/16W
R144 1-216-789-11 METAL CHIP 2.2 5% 1/16W
R225 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R226 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
(US,AUS)
R226 1-216-864-11 METAL CHIP 0 5% 1/16W
(E4,E92,MX,SP,AR)
R227 1-216-833-11 METAL CHIP 10K 5% 1/16W
R228 1-216-817-11 METAL CHIP 470 5% 1/16W
(E4,E92,MX,SP,AR)
R228 1-216-819-11 METAL CHIP 680 5% 1/16W
(US,AUS)
R230 1-216-811-11 METAL CHIP 150 5% 1/16W
R231 1-216-839-11 METAL CHIP 33K 5% 1/16W
(E4,E92,MX,SP,AR)
R231 1-216-841-11 METAL CHIP 47K 5% 1/16W
(US,AUS)
R232 1-216-809-11 METAL CHIP 100 5% 1/16W
R240 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R241 1-216-831-11 METAL CHIP 6.8K 5% 1/16W
R242 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R243 1-216-853-11 METAL CHIP 470K 5% 1/16W
R244 1-216-789-11 METAL CHIP 2.2 5% 1/16W
R306 1-216-833-11 METAL CHIP 10K 5% 1/16W
R321 1-216-813-11 METAL CHIP 220 5% 1/16W
R322 1-216-833-11 METAL CHIP 10K 5% 1/16W
R323 1-216-857-11 METAL CHIP 1M 5% 1/16W
R324 1-216-845-11 METAL CHIP 100K 5% 1/16W
R325 1-216-817-11 METAL CHIP 470 5% 1/16W
R331 1-216-809-11 METAL CHIP 100 5% 1/16W
R332 1-216-809-11 METAL CHIP 100 5% 1/16W
R333 1-216-833-11 METAL CHIP 10K 5% 1/16W
R335 1-216-813-11 METAL CHIP 220 5% 1/16W
R382 1-216-813-11 METAL CHIP 220 5% 1/16W
R383 1-216-813-11 METAL CHIP 220 5% 1/16W
R384 1-216-813-11 METAL CHIP 220 5% 1/16W
R385 1-216-815-11 METAL CHIP 330 5% 1/16W
R802 1-216-841-11 METAL CHIP 47K 5% 1/16W
R803 1-216-841-11 METAL CHIP 47K 5% 1/16W
R804 1-216-833-11 METAL CHIP 10K 5% 1/16W
R805 1-216-833-11 METAL CHIP 10K 5% 1/16W
R807 1-216-833-11 METAL CHIP 10K 5% 1/16W
R809 1-216-833-11 METAL CHIP 10K 5% 1/16W
R814 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R815 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R816 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R820 1-216-819-11 METAL CHIP 680 5% 1/16W
(US)
R820 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
(SP)
R820 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
(E4,AR)
R820 1-216-835-11 METAL CHIP 15K 5% 1/16W
(AUS)
66
CFD-S26
POWER (1)MAIN
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R820 1-216-864-11 METAL CHIP 0 5% 1/16W
(E92,MX)
R821 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
(US,E4,AUS,SP,AR)
R822 1-216-835-11 METAL CHIP 15K 5% 1/16W
R824 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R825 1-216-821-11 METAL CHIP 1K 5% 1/16W
R827 1-216-821-11 METAL CHIP 1K 5% 1/16W
R828 1-216-809-11 METAL CHIP 100 5% 1/16W
R829 1-216-821-11 METAL CHIP 1K 5% 1/16W
R830 1-216-821-11 METAL CHIP 1K 5% 1/16W
R831 1-216-821-11 METAL CHIP 1K 5% 1/16W
T1 1-433-741-11 TRANSFORMER, IF
T2 1-419-465-11 COIL (DET)
(SP)
X1 1-760-130-11 VIBRATOR, CRYSTAL (75kHz)
X801 1-795-267-11 VIBRATOR, CRYSTAL (32.768kHz)
X802 1-781-775-21 VIBRATOR, CERAMIC (4.19MHz)
*************************************************************
* 1-679-969-11 POWER (1) BOARD (FORMER)
< TRANSFORMER >
< VIBRATOR >
****************
R832 1-216-841-11 METAL CHIP 47K 5% 1/16W
R833 1-216-821-11 METAL CHIP 1K 5% 1/16W
R835 1-216-841-11 METAL CHIP 47K 5% 1/16W
R836 1-216-841-11 METAL CHIP 47K 5% 1/16W
R837 1-216-809-11 METAL CHIP 100 5% 1/16W
R838 1-216-821-11 METAL CHIP 1K 5% 1/16W
R840 1-216-821-11 METAL CHIP 1K 5% 1/16W
R841 1-216-821-11 METAL CHIP 1K 5% 1/16W
R842 1-216-821-11 METAL CHIP 1K 5% 1/16W
R843 1-216-821-11 METAL CHIP 1K 5% 1/16W
R844 1-216-835-11 METAL CHIP 15K 5% 1/16W
R845 1-216-841-11 METAL CHIP 47K 5% 1/16W
R846 1-216-821-11 METAL CHIP 1K 5% 1/16W
R847 1-216-821-11 METAL CHIP 1K 5% 1/16W
R848 1-216-809-11 METAL CHIP 100 5% 1/16W
R849 1-216-841-11 METAL CHIP 47K 5% 1/16W
R850 1-216-821-11 METAL CHIP 1K 5% 1/16W
R854 1-216-841-11 METAL CHIP 47K 5% 1/16W
R859 1-216-821-11 METAL CHIP 1K 5% 1/16W
R860 1-216-841-11 METAL CHIP 47K 5% 1/16W
R861 1-216-821-11 METAL CHIP 1K 5% 1/16W
R862 1-216-821-11 METAL CHIP 1K 5% 1/16W
R865 1-216-841-11 METAL CHIP 47K 5% 1/16W
R866 1-216-845-11 METAL CHIP 100K 5% 1/16W
R867 1-216-819-11 METAL CHIP 680 5% 1/16W
1-533-233-31 HOLDER, FUSE (AUS,SP)
< CAPACITOR >
C901 1-162-995-11 CERAMIC CHIP 0.022uF 50V
C902 1-162-995-11 CERAMIC CHIP 0.022uF 50V
C903 1-162-995-11 CERAMIC CHIP 0.022uF 50V
C904 1-162-995-11 CERAMIC CHIP 0.022uF 50V
C906 1-126-964-11 ELECT 10uF 20% 50V
< AC INLET >
0 CNJ901 1-526-818-11 INLET, AC (- AC IN) (E92)
0 CNJ901 1-526-838-11 INLET, AC 2P (- AC IN) (AUS,SP)
0 CNJ901 1-540-009-11 INLET, AC (- AC IN) (US)
< CONNECTOR >
* CNP901 1-815-551-11 PIN, CONNECTOR (PC BOARD) 3P
* CNP902 1-815-552-21 PIN, CONNECTOR (PC BOARD) 4P
< DIODE >
D901 8-719-063-79 DIODE 1N4002B
D902 8-719-063-79 DIODE 1N4002B
D903 8-719-063-79 DIODE 1N4002B
D904 8-719-063-79 DIODE 1N4002B
< FUSE >
R868 1-216-819-11 METAL CHIP 680 5% 1/16W
R869 1-216-819-11 METAL CHIP 680 5% 1/16W
R870 1-216-819-11 METAL CHIP 680 5% 1/16W
R876 1-216-817-11 METAL CHIP 470 5% 1/16W
R901 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R902 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R903 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R951 1-216-841-11 METAL CHIP 47K 5% 1/16W
R952 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R954 1-216-821-11 METAL CHIP 1K 5% 1/16W
R955 1-216-821-11 METAL CHIP 1K 5% 1/16W
R958 1-216-815-11 METAL CHIP 330 5% 1/16W
R960 1-216-864-11 METAL CHIP 0 5% 1/16W
0 F902 1-533-469-11 FUSE, TIME-LAG (T2.5AL/250V) (AUS,SP)
< CABLE HOLDER >
* KH903 1-573-287-11 HOLDER, CABLE 2P
*************************************************************
* 1-679-969-11 POWER (1) BOARD (NEW)
****************
1-533-233-31 HOLDER, FUSE (E4,SP,AUS,AR)
< CAPACITOR >
C901 1-162-995-11 CERAMIC CHIP 0.022uF 50V
C902 1-162-995-11 CERAMIC CHIP 0.022uF 50V
C903 1-162-995-11 CERAMIC CHIP 0.022uF 50V
C904 1-162-995-11 CERAMIC CHIP 0.022uF 50V
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
67
CFD-S26
POWER (1) POWER (2) PRE
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C906 1-126-964-11 ELECT 10uF 20% 50V
< AC INLET >
0 CNJ901 1-526-818-11 INLET, AC (- AC IN) (E92,MX)
0 CNJ901 1-526-838-11 INLET, AC 2P (- AC IN) (SP,AUS,AR)
0 CNJ901 1-540-009-11 INLET, AC (- AC IN) (US,E4)
< CONNECTOR >
* CNP901 1-815-551-11 PIN, CONNECTOR (PC BOARD) 3P
* CNP902 1-815-552-21 PIN, CONNECTOR (PC BOARD) 4P
< DIODE >
D901 8-719-063-79 DIODE 1N4002B
D902 8-719-063-79 DIODE 1N4002B
D903 8-719-063-79 DIODE 1N4002B
D904 8-719-063-79 DIODE 1N4002B
C204 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C205 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
C206 1-126-960-11 ELECT 1uF 20% 50V
C207 1-162-962-11 CERAMIC CHIP 470PF 10% 50V
C301 1-104-665-11 ELECT 100uF 20% 10V
C302 1-104-665-11 ELECT 100uF 20% 10V
C303 1-104-665-11 ELECT 100uF 20% 10V
C304 1-104-664-11 ELECT 47uF 20% 10V
C305 1-162-962-11 CERAMIC CHIP 470PF 10% 50V
C306 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C307 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
< CONNECTOR >
CNP301 1-568-830-11 CONNECTOR, FFC 11P
< IC >
< FUSE >
0 F902 1-532-388-51 FUSE, TIME-LAG (T2AL/250V) (E4)
0 F902 1-533-469-11 FUSE, TIME-LAG (T2.5AL/250V) (SP,AUS,AR)
< CABLE HOLDER >
* KH903 1-573-287-11 HOLDER, CABLE 2P
*************************************************************
* 1-679-970-11 POWER (2) BOARD (FORMER)
****************
< CABLE HOLDER >
* KH905 1-573-287-11 HOLDER, CABLE 2P
*************************************************************
* 1-679-970-11 POWER (2) BOARD (NEW)
****************
< CABLE HOLDER >
* KH905 1-573-287-11 HOLDER, CABLE 2P
*************************************************************
* A-3347-167-A PRE BOARD, COMPLETE
********************
< CAPACITOR >
C101 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C102 1-104-664-11 ELECT 47uF 20% 10V
C103 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V
C104 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C105 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
C106 1-126-960-11 ELECT 1uF 20% 50V
C107 1-162-962-11 CERAMIC CHIP 470PF 10% 50V
C201 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C202 1-104-664-11 ELECT 47uF 20% 10V
C203 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V
IC301 8-759-264-71 IC TA2068N (FORMER)
IC301 8-759-264-71 IC TA2068N (NEW)
< JUMPER RESISTOR >
JC301 1-216-864-11 METAL CHIP 0 5% 1/16W
JC302 1-216-864-11 METAL CHIP 0 5% 1/16W
JC303 1-216-864-11 METAL CHIP 0 5% 1/16W
JC304 1-216-864-11 METAL CHIP 0 5% 1/16W
< TRANSISTOR >
Q301 8-729-120-28 TRANSISTOR 2SC1623-L5L6
< RESISTOR >
R101 1-216-835-11 METAL CHIP 15K 5% 1/16W
R102 1-216-807-11 METAL CHIP 68 5% 1/16W
R103 1-216-843-11 METAL CHIP 68K 5% 1/16W
R104 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R105 1-216-835-11 METAL CHIP 15K 5% 1/16W
R106 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R110 1-216-809-11 METAL CHIP 100 5% 1/16W
R111 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R201 1-216-835-11 METAL CHIP 15K 5% 1/16W
R202 1-216-807-11 METAL CHIP 68 5% 1/16W
R203 1-216-843-11 METAL CHIP 68K 5% 1/16W
R204 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R205 1-216-835-11 METAL CHIP 15K 5% 1/16W
R206 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R210 1-216-025-11 RES-CHIP 100 5% 1/10W
R211 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R301 1-216-857-11 METAL CHIP 1M 5% 1/16W
R302 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R303 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R304 1-216-821-11 METAL CHIP 1K 5% 1/16W
R305 1-216-811-11 METAL CHIP 150 5% 1/16W
R306 1-216-831-11 METAL CHIP 6.8K 5% 1/16W
R307 1-216-799-11 METAL CHIP 15 5% 1/16W
68
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
CFD-S26
PRE VOLTAGE SELECT
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R308 1-216-837-11 METAL CHIP 22K 5% 1/16W
R309 1-216-805-11 METAL CHIP 47 5% 1/16W
ACCESSORIES & PACKING MATERIALS
*******************************
< SWITCH >
S301 1-762-565-11 SWITCH, SLIDE (REC/PB)
< TRANSFORMER >
T301 1-416-041-11 TRANSFORMER, BIAS OSCILLATION
*************************************************************
* 1-682-250-14 VOLTAGE SELECT BOARD (E4) (NEW)
*********************
< SWITCH >
0 S901 1-552-921-00 SWITCH, POWER (VOLTAGE SELECTOR) (E4)
*************************************************************
MISCELLANEOUS
***************
* 11 1-757-559-11 CABLE, FLAT 8P
117 1-452-899-11 MAGNET
124 1-792-684-11 WIRE (FLAT TYPE) (16 CORE)
0 251 8-848-483-05 PICK-UP, OPTICAL KSS-213C/Q-RP
255 X-2646-381-1 CHASSIS ASSY (MB), MOTOR (SPINDLE)
(including M701)
ANT1 1-501-883-21 ANTENNA, TELESCOPIC
0 F902 1-532-388-51 FUSE, TIME-LAG (T2AL/250V) (E4)
0 F902 1-533-469-11 FUSE, TIME-LAG (T2.5AL/250V) (SP,AUS,AR)
HE301 1-543-876-11 HEAD (ERASE)
HRP301 1-500-668-11 HEAD, MAGNETIC (RECORD/PLAYBACK)
0 1-557-287-11 CORD, POWER (E92,MX)
0 1-569-008-21 ADAPTOR, CONVERSION (E4)
0 1-696-819-11 CORD, POWER (AUS)
0 1-696-820-21 CORD, POWER (E4,SP)
0 1-783-878-11 CORD, POWER (US)
0 1-783-952-11 CORD, POWER (AR)
3-227-155-14 MANUAL, INSTRUCTION (ENGLISH)
(US,E92,MX)
3-227-155-31 MANUAL, INSTRUCTION (SPANISH) (E92,MX)
3-227-155-41 MANUAL, INSTRUCTION (ENGLISH,SPANISH)
(E4,AUS,SP,AR)
3-227-155-51 MANUAL, INSTRUCTION (FRENCH,GERMAN)
(SP)
3-227-155-61 MANUAL, INSTRUCTION (DUTCH,PORTUGUESE)
(E4)
*************************************************************
**************
HARDWARE LIST
**************
#1 7-685-647-79 SCREW +BVTP 3X10 TYPE2 N-S
#2 7-685-648-79 SCREW +BVTP 3X12 TYPE2 N-S
#3 7-685-853-04 SCREW +BVTT 2X6 (S)
#4 7-621-770-87 SCREW +B 2.6X5
#5 7-682-548-04 SCREW +B 3X8
M702 X-2625-769-1 GEAR ASSY (MB), MOTOR (SLED)
M801 A-3320-446-A MOTOR ASSY (CAPSTAN/REEL)
S801 1-692-960-11 SWITCH, PUSH (1 KEY) (Z PUSH OPEN/CLOSE)
S802 1-762-679-11 SWITCH, LEAF (TAPE PLAY)
SP301 1-529-723-21 SPEAKER (10cm) (L-CH)
SP302 1-529-723-21 SPEAKER (10cm) (R-CH)
0 T901 1-435-921-11 TRANSFORMER, POWER (AUS,SP,AR)
0 T901 1-435-922-11 TRANSFORMER, POWER (E4)
0 T901 1-435-974-11 TRANSFORMER, POWER (US,E92,MX)
*************************************************************
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
69
CFD-S26
MEMO
70
SERVICE MANUAL
SERVICE MANUAL
Ver 1.2 2002. 06
SUPPLEMENT-1
File this supplement with the service manual.
Subject : Change of CD Mechanism
CFD-S26
US Model
E Model
Australian Model
(SPM-02027)
CD mechanism changed to KSM-213RDP from KSM-213CDP after serial
No. 2341962.
Please check serial No. when you exchange the parts of CD mechanism.
CFD-S26
CD MECHANISM SECTION
(KSM-213RDP)
253
254
255
251
258 258
257
M701
M702
256
252
259
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
Ref. No. Part No. Description Remark
251 2-626-908-01 SHAFT, SLED
* 252 2-647-408-02 GEAR (B)
0 253 8-820-161-02 PICK-UP, OPTICAL KSS-213R/C2RP
* 254 2-169-065-01 GEAR (A)
* 255 2-169-384-01 SHAFT (S), GEAR
* 256 2-169-385-01 SPRING, SLED
2
Ref. No. Part No. Description Remark
257 3-713-786-51 SCREW (M2X3)
258 2-169-388-01 TAPPING (M2), +PWB
259 X-2162-707-1 CHASSIS ASSY (RDP) (RP), MOTOR (SPINDLE)
(including M701)
M702 X-2162-712-1 GEAR ASSY (R) (RP), MOTOR (SLED)
MEMO
CFD-S26
3
CFD-S26
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper on the revised page allows you to jump to the next revised page.
Ver. Date Description of Revision
1.0 2001. 03 New
1.1 2001. 05 AR, E4, E92 and MX model have been added.
1.2 2002. 06 Change of CD mechanism, and part No. correction. (SPM-02027)
4
Loading...