Sony CFD-E100 Owner Manual

Component code
numbers

TV

The left row of the table shows the brand, the
right row shows the code number.

CBL (Analog cable box)

The left row of the table shows the brand and
the right row shows the code number.

To set a component code (see
“Setting the code” on the back side
for details)

TV

Brand

Sony
Admiral
Akai
AOC
Audinac
Bell&Howell
Broksonic
Craig
Croslex
Crown
Curtis Mathis
Daewoo
Daytron
Emerson

Fisher
General Electric
GoldStar/LG

Hitachi
JC Penny
JVC
KTV
LXI(Sears)

Magnavox

Marantz
Mitsubishi/MGA
NEC
Panasonic

Philco

Philips
Pioneer
Portland
Quasar
Radio Shack
RCA/PROSCAN

Samsung
Sanyo
Scott
Sharp
Signature 2000
Sylvania
Symphonic
Toshiba

Videch
Wards
Zenith

Code No.

001
002, 014, 009
003
012
034
014, 009, 038
003, 012, 072
022, 034, 020, 021
011
034
003, 019, 034
035, 036, 003, 041, 029
013
022, 013, 020, 021, 003,

015, 042, 034
025
002, 018, 003, 007, 045
003, 013, 012, 030, 046,

050, 051, 049
031, 013, 003, 032
003, 002, 030, 007
028
033, 013, 003, 034
002, 003, 011, 025, 019,

012, 052
011, 012, 013, 003, 043,

047
024
024, 003, 012, 066
003, 012
018, 016, 007, 049, 067,

074, 076
011, 013, 003, 068, 035,

031
011, 056, 043, 017
037, 018, 019
003, 008
018, 007, 048
002, 012, 024, 023
002, 003, 004, 005, 006,

007, 008, 044, 045, 046,
053

026, 012, 013, 003, 055
025, 023, 054
034, 012
014, 013, 015, 070
014, 009
011, 012, 003, 073
023, 039, 040, 034
060, 019, 014, 052, 059,

075
031, 003, 012
013, 003, 015, 012
009, 010

Analog cable box

Brand

Hamlin/Regal
Jerrold/G.I

Oak
Panasonic
Pioneer
Scientific Atlanta
Tocom
Zenith

Code No.

022, 023, 024, 025, 026
031, 001, 002, 003, 004,

005, 006, 007, 008, 018,
022, 032

027, 028, 029
019, 020, 021
014, 015
009, 010, 011
031, 016, 017
012, 013

Precautions

On safety

• As the laser beam used in the CD player
section is harmful to the eyes, do not
attempt to disassemble the casing. Refer
servicing to qualified personnel only.

• Should any solid object or liquid fall into
the player, unplug the player, and have it
checked by qualified personnel before
operating it any further.

• Discs with non-standard shapes (e.g.,
heart, square, star) cannot be played on
this player. Attempting to do so may
damage the player. Do not use such discs.

Cleaning the cabinet

• Clean the cabinet, panel and controls with
a soft cloth slightly moistened with a mild
detergent solution. Do not use any type of
abrasive pad, scouring powder, or solvent,
such as alcohol or benzine.

On power sources

• For AC operation, use the supplied AC
power cord; do not use any other type.

• The player is not disconnected from the
AC power source (mains) as long as it is
connected to the wall outlet, even if the
player itself has been turned off.

• Unplug the player from the wall outlet
when it is not be used for an extended
period of time.

• For battery operation, use six size C (R14)
batteries.

• When the batteries are not to be used,
remove them to avoid damage that can be
caused by battery leakage or corrosion.

• The nameplate indicating operating
voltage, power consumption, etc. is
located at the bottom.

On placement

• Do not leave the player in a location near
heat sources, or in a place subject to direct
sunlight, excessive dust or mechanical
shock.

• Do not place the player on an inclined or
unstable place.

• Do not place anything within 10 mm of
the side of the cabinet. The ventilation
holes must be unobstructed for the player
to operate properly and prolong the life of
its components.

• If the player is left in a car parked in the
sun, be sure to choose a location in the car
where the player will not be subjected to
the direct rays of the sun.

• Since a strong magnet is used for the
speakers, keep personal credit cards using
magnetic coding or spring-wound watches
away from the player to prevent possible
damage from the magnet.

On operation

• If the player is brought directly from a
cold to a warm location, or is placed in a
very damp room, moisture may condense
on the lenses inside the CD player section.
Should this occur, the player will not
operate properly. In this case, remove the
CD and wait about an hour for the
moisture to evaporate.

• If the player has not been used for a long
time, set it in the playback mode to warm
it up for a few minutes before inserting a
cassette.

Notes on cassettes

• Break off the cassette tab from side A or B
to prevent accidental recording. If you
want to reuse the tape for recording, cover
the broken tab with adhesive tape.

Side A

Tab for side A

Tab for side B

• The use of a cassette with more than 90
minutes of play time is not recommended
except for long, continuous recording or
playback.

Notes on CDs

• Before playing, clean the CD with a
cleaning cloth. Wipe the CD from the
center out.

• Do not use solvents such as benzine,
thinner, commercially available cleaners
or anti-static spray intended for vinyl LPs.

• Do not expose the CD to direct sunlight or
heat sources such as hot air ducts, nor
leave it in a car parked in direct sunlight as
there can be a considerable rise in
temperature inside the car.

• Do not stick paper or sticker on the CD,
nor scratch the surface of the CD.

• After playing, store the CD in its case.

If there is a scratch, dirt or fingerprints on the
CD, it may cause tracking error.

About CD-Rs/CD-RWs

This player can play CD-Rs/CD-RWs
recorded in the CD-DA format*, but
playback capability may vary depending on
the quality of the disc and the condition of
the recording device.

* CD-DA is the abbreviation for Compact

Disc Digital Audio. It is a recording
standard used for Audio CDs.

Music discs encoded with copyright
protection technologies

This product is designed to play back discs
that conform to the Compact Disc (CD)
standard. Recently, various music discs
encoded with copyright protection
technologies are marketed by some record
companies. Please be aware that among
those discs, there are some that do not
conform to the CD standard and may not be
playable by this product.

If you have any questions or problems
concerning your player, please consult your
nearest Sony dealer.

Troubleshooting

General

The power does not come on.

• Connect the AC power cord to the wall outlet
securely.

• Make sure the batteries are inserted correctly.

• Replace all the batteries with new ones if they
are weak.

• You cannot turn on the player with the remote
when you operate the player on batteries .

There is no audio.

• Adjust the volume.

• Unplug the headphones when listening
through speakers.

Noise is heard.

• Someone is using a portable telephone or
other equipment that emits radio waves near
the player. tMove the portable telephone,
etc., away from the player.

CD Player

The CD does not play or “no dISC”
lights in the display even when a CD
is in place.

• Place the CD with the label surface up.

• Clean the CD.

• Take out the CD and leave the CD
compartment open for about an hour to dry
moisture condensation.

• The CD-R/CD-RW was not finalized. Finalize
the CD-R/CD-RW with the recording device.

• There is a problem with the quality of the CD­R/CD-RW, recording device, or application
software.

• The CD-R/CD-RW is blank.

• Replace all the batteries with new ones if they
are weak.

The sound drops out.

• Reduce the volume.

• Clean the CD, or replace it if the CD is badly
damaged.

• Place the player in a location free from
vibration.

• Clean the lens with a commercially available
blower.

• The sound may drop out or noise may be
heard when using poor quality CD-Rs/CD­RWs or if there is a problem with the
recording device or application software.

Radio

Reception is poor.

• Reorient the antenna to improve FM
reception.

• Reorient the player itself to improve AM
reception.

The audio is weak or has poor quality.

• Replace all the batteries with new ones if they
are weak.

• Move the player away from the TV.

The picture of your TV becomes
unstable.

• If you are listening to an FM program near the
TV with an indoor antenna, move the player
away from the TV.

Tape Player

The tape does not move when you
press an operation button.

• Close the cassette compartment securely.

The z button does not function or the
tape does not play or record.

• Make sure the safety tab on the cassette is in
place.

Poor or distorted playback, recording
or erasing quality.

• Clean the heads, pinch roller and capstan with
a cleaning swab slightly moistened with
cleaning fluid or alcohol.

• Replace all the batteries with new ones if they
are weak.

• TYPE II (high position) or TYPE IV (metal)
tape is being used. Use TYPE I (normal) tape
only.

• Demagnetize the heads using a commercially
available tape head demagnetizer.

Record/playback head

Capstan

Erase head Pinch roller

Lens

Remote

The remote does not function.

• Make sure that the TV•CD/RADIO switch on
the remote is set correctly.
To control CD or radio: set it to CD/RADIO.
To control a TV or analog cable box: set it to
TV.

• Replace all the batteries in the remote with
new ones if they are weak.

• Make sure that you are pointing the remote at
the remote sensor on the player.

• Remove any obstacles in the path of the
remote and the player.

• Make sure the remote sensor is not exposed to
strong light such as direct sunlight or
fluorescent lamp light.

• Move closer to the player when using the
remote.

TV or analog cable box cannot be
operated using the remote.

• Check that the button of the TV or CBL is
pressed to choose your desired component.

• Check that the component has infrared remote
capability. For example, if your component
didn’t come with the remote, it probably isn’t
capable of being controlled by the remote.

Should any problem persist, reset the remote to
the factory setting by pressing the POWER, TV/
VIDEO and VOL – buttons simultaneously.

After trying the above remedies, if you still have
problems, unplug the AC power cord and
remove all the batteries. After all the indications
in the display disappear, plug the power cord
and insert the batteries again. If the problem
persists, please consult your nearest Sony dealer.

Specifications

AUDIO POWER SPECIFICATIONS

POWER OUTPUT AND TOTAL
HARMONIC DISTORTION

With 3.2-ohm loads, both channels driven
from 100 - 10,000 Hz; rated 1.5 W per
channel-minimum RMS power, with no
more than 10 % total harmonic distortion
in AC operation.

Other specifications

CD player section

System

Compact disc digital audio system

Laser diode properties

Emission duration: Continuous
Laser output: Less than 44.6 µW
(This output is the value measured at a distance

of about 200 mm from the objective lens surface
on the optical pick-up block with 7 mm
aperture.)

Spindle speed

200 r/min (rpm) to 500 r/min (rpm)
(CLV)

Number of channels

2

Frequency response

20 - 20 000 Hz +1/–2 dB

Wow and flutter

Below measurable limit

Radio section

Frequency range

FM: 87.5 - 108 MHz
AM: 530 - 1 710 kHz

Antennas

FM: Telescopic antenna
AM: Built-in ferrite bar antenna

Cassette-corder section

Recording system

4-track 2 channel stereo

Fast winding time

Approx. 120 s (sec.) with Sony cassette C-60

Frequency response

TYPE I (normal): 80 - 13 000 Hz

General

Speaker

Full range: 8 cm (3
cone type (2)

Outputs

Headphones jack (stereo minijack)
For 16 - 68 Ω impedance headphones

Power output

1.8 W + 1.8 W (at 3.2 Ω, 10% harmonic
distortion)

Power requirements

For CD radio cassette-corder:
120 V AC, 60Hz
9 V DC, 6 size C (R14) batteries
For remote control:
3 V DC, 2 size AAA (R03) batteries

Power consumption

AC 14 W

Battery life

For CD radio cassette-corder:

FM recording

Sony R14P: approx. 13.5 h
Sony alkaline LR14: approx. 20 h

Tape playback

Sony R14P: approx. 7.5 h
Sony alkaline LR14: approx. 15 h

CD playback

Sony R14P: approx. 2.5 h
Sony alkaline LR14: approx. 7 h

Dimensions

Approx. 385 × 190.5 × 170 mm (w/h/d)
(15 1⁄4 × 7 1⁄2 × 6 3⁄4 inches) (incl. projecting parts)

Mass

Approx. 3.1 kg (6 lb. 13.4 oz) (incl. batteries)

Supplied accessory

AC power cord (1)
Remote control (1)

Design and specifications are subject to change
without notice.

3⁄20 inches)

dia., 3.2 Ω,

English

WARNING

To prevent fire or shock hazard, do
not expose the player to rain or
moisture.

CD Radio
Cassette­Corder

Operating Instructions

CAUTION

The use of optical instruments with this product
will increase eye hazard.

WARNING

Do not install the appliance in a confined space,
such as a bookcase or built-in cabinet.

CFD-E100

©2005 Sony Corporation
Printed in China

To prevent fire or shock hazard, do not place
objects filled with liquids, such as vases, on the
appliance.

2-587-606-11 (1)

Power Sources

B

Connect the AC power cord A or insert six size C (R14) batteries (not supplied) into the battery
compartment B .

Notes

• Replace the batteries when the OPR/BATT indicator dims or when the player stops operating.
Replace all the batteries with new ones. Before you replace the batteries, be sure to take out the CD
from the player.

• To use the player on batteries, disconnect the AC power cord from the player.

• When you operate the player on batteries, you cannot turn on the player using the remote.

Preparing the remote C

Insert two size AAA (R03) batteries (not supplied).

Replacing batteries

With normal use, the batteries should last for about six months. When the remote no longer
operates the player, replace all the batteries with new ones.

Note

Do not take more than 3 minutes to replace the batteries as your code number settings will be erased.

This symbol is intended to alert the
user to the presence of uninsulated
“dangerous voltage” within the
product's enclosure that may be of
sufficient magnitude to constitute a
risk of electric shock to persons.

This symbol is intended to alert the
user to the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the
appliance.

A

1 to AC IN

Information

For customers in the USA

This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment
generates, uses and can radiate radio frequency
energy and, if not installed and used in
accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be
determined by turning the equipment off and on,
the user is encouraged to try to correct the
interference by one or more of the following
measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the

equipment and receiver.

— Connect the equipment into an outlet on a

circuit different from that to which the
receiver is connected.

— Consult the dealer or an experienced radio/

TV technician for help.
This device complies with part 15 of the FCC
rules. Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired operation.
You are cautioned that any changes or
modifications not expressly approved in this
manual could void your authority to operate this
equipment.

C

2 to the wall outlet

Owner's Record

The model number is located at the bottom and
the serial number is located in the battery
compartment.
Record these numbers in the spaces provided
below. Refer to them whenever you call upon
your Sony dealer regarding this product.
Model No. CFD-E100
Serial No.

For customers in the USA

Please register this product on line at
http://www.sony.com/productregistration.
Proper registration will enable us to send you
periodic mailings about new product,
services and other important announcements.
Registering your product will also allow us to
contact you in the unlikely event that the
product needs adjustment or modification.
Thank you.

Printed on 100% recycled paper
using VOC (Volatile Organic
Compound)-free vegetable oil
based ink.

Optional accessories

Sony MDR headphone series

Location of controls

Loading a CD

POWER

i

Remote sensor

Display

DE

Total track number

To turn on/off the power

Press POWER.

To adjust the volume

Press VOLUME +, – (VOL +, – on the remote).

To listen through headphones

Connect the headphones to the i (headphones) jack.

Adjusting the sound emphasis

To reinforce the bass sound

Press MEGA BASS.
“MEGA BASS” appears in the display.
To return to normal sound, press the button again.

Falling asleep to music

1 Play the music source you want.
2 Press SLEEP to display “SLEEP.”
3 Press SLEEP to select the minutes until the player goes off automatically.

Each time you press the button, the indication changes as follows:
“60” t “90” t “120” t “OFF” t “10” t “20” t “30”.

To cancel the sleep function

Press POWER to turn off the power.

Note

When you are playing a tape using this function:
If the tape length of one side is longer than the set time, the player will not go off until the tape reaches
the end.

With the labeled side up

u*

SLEEP

OPR/BATT

Inserting a cassette

With the side you want
to play facing out

*

PRESET +, –

x

Display

DISPLAY
ENTER/MEMORY

.,>

MEGA BASS

MODE

PUSH CLOSE

Total playing time

VOLUME +*, –

TUNE +, –

RADIO BAND
AUTO PRESET

Z OPEN

Programmed track

Remote Control

SLEEP

FUNCTION

Number buttons

MODE

TUNE/CH +,–

RADIO BAND

MEGA BASS

N

RECALL

TV/VIDEO

TV

CBL

*The button has a tactile dot.

POWER

ENT

VOL +*, –

x

X

.,>

MUTING

SET

Playing order

About the remote control

You can use the supplied remote control to operate a TV or analog cable box, as well.
Set the TV•CD/RADIO switch as follows:
To operate this player: set it to CD/RADIO
To operate a TV or analog cable box: set it to TV
For details on using the remote control to operate a TV or analog cable box, see “Using the

remote control to operate a TV”.

Playing a CD

1 Press Z OPEN to open the CD compartment.
2 Load a CD in the CD compartment until it clicks into place.
3 Press PUSH CLOSE to close the CD compartment.
4 Press u (N on the remote).

The player plays all the tracks once.

To Do this

stop playback Press x.
pause playback Press u (X on the remote).

go to the next track Press >.
find the beginning of the current Press ..

track/go back to the previous track
remove the CD Press Z OPEN.
locate a point while listening Press and hold > (forward) or . (backward) while

to the sound playing until you find the point.
locate a point while observing Press and hold > (forward) or . (backward) in pause

the display until you find the point.
locate a specific track directly* Press a number button of the track on the remote.

* You cannot locate a specific track if “SHUF” or “PGM” is lit in the display. Turn off the indication by

pressing x.

Tip

To locate a track numbered over 10, press >10 first, then the corresponding number buttons on the
remote.
Example: To play track number 23, press >10 first, then 2 and 3.

Note

When using the remote, make sure that the TV•CD/RADIO switch on the remote is set to CD/RADIO.

Using the display

To check the total track number and playing time

Press DISPLAY•ENTER/MEMORY in stop mode (see fig. D).

To check the remaining time

Press DISPLAY•ENTER/MEMORY repeatedly while playing a CD. The display changes as
follows:

t the current track number and playing time

r

the current track number and the remaining time on the current track*

r

the number of tracks left and remaining time on the CD

* For a track whose number is more than 20, the remaining time appears as “- -:- -” in the display.

Selecting the play mode

Press MODE until “REP 1” “REP ALL” “SHUF” “SHUF REP” “PGM” “PGM REP” appears in
the display. Then proceed as follows:

To Select Then do this

repeat a single track “REP 1” Press . or > to select the track that you

repeat all the track “REP ALL” Press u.
shuffle play “SHUF” Press u.
repeat tracks “SHUF REP” Press u.

in random order
program play “PGM” Press . or > then press DISPLAY•ENTER/

repeat programed tracks “PGM REP” Press . or > then press DISPLAY•ENTER/

On the remote

When you’ve selected “PGM” or “PGM REP”, press the number buttons for the track you want
up to 20 tracks, then press N.

To cancel selected play mode

Press MODE repeatedly until the selected mode disappears from the display.

To check the programed track and playing order in the display

To check the order of tracks before play, press DISPLAY•ENTER/MEMORY.
Every time you press the button, the track number appears in the programed order.

To change the current program

Press x once if the CD is stopped and twice if the CD is playing. The current program will be
erased. Then create a new program following the programing procedure.

Tips

• You can play the same program again, since the program is saved until you open the CD
compartment.

• You can record your own program. After you’ve created the program, insert a blank tape and press z
to start recording.

Press the button again to resume play after pause.

want to repeat, then press u.

MEMORY for the tracks you want to program in
the order you want up to 20 tracks (see fig. E).
Then press u.

MEMORY for the tracks you want to program in
the order you want up to 20 tracks. Then Press
u.

Listening to the radio

1 Press RADIO BAND•AUTO PRESET until the band you want appears in the

display (direct power-on).
Each time you press the button, the indication changes as follows:
“FM” t “AM”.

2 Hold down TUNE (TUNE/CH on the remote) + or – until the frequency digits

begin to change in the display.
The player automatically scans the radio frequencies and stops when it finds a

clear station.
If you can't tune in a station, press the button repeatedly to change the frequency
step by step.

Tip

If the FM broadcast is noisy, press MODE repeatedly until “Mono” appears in the display and the radio
will play in monaural.

Note

When using the remote, make sure that the TV•CD/RADIO switch on the remote is set to CD/RADIO.

Presetting radio stations

You can store radio stations into the player’s memory. You can preset up to 30 radio stations , 20
for FM and 10 for AM in any order.

1 Press RADIO BAND•AUTO PRESET to select the band.
2 Hold down RADIO BAND•AUTO PRESET for 2 seconds until “AUTO” flashes

in the display.

3 Press DISPLAY•ENTER/MEMORY.

The stations are stored in memory from the lower frequencies to the higher ones.

If a station cannot be preset automatically

You need to preset a station with a weak signal manually.

1 Press RADIO BAND•AUTO PRESET to select the band.
2 Tune in a station you want.
3 Hold down DISPLAY•ENTER/MEMORY for 2 seconds until the preset number flashes in

the display.

4 Press PRESET + or – until the preset number you want for the station flashes in the display.
5 Press DISPLAY•ENTER/MEMORY.

The new station replaces the old one.

On the remote

1 Press RADIO BAND until the band you want appears in the display.
2 Tune in a station you want.
3 Hold down the number buttons that you want to preset the new station on for about 2 seconds.

To select the preset number over 10, press >10 first, then the corresponding number buttons.
You need to hold down the last number button to enter for about 2 seconds.
(Example: To select 12, press >10 and 1 first, then hold down 2 for about 2 seconds.)

Tip

The preset radio stations remain in memory even if you unplug the AC power cord or remove the
batteries.

Playing preset radio stations

1 Press RADIO BAND•AUTO PRESET to select the band.
2 Press PRESET + or – to tune in the stored station.

On the remote

1 Press RADIO BAND.
2 Press the number buttons to tune in the stored station.

To tune in a preset station over 10, press >10 first, then corresponding number buttons.
(Example: To tune in a preset station 12, press >10 and 1 first, and then press 2.)

Playing a tape

1 Press xZ to open the tape compartment and insert a recorded tape. Close the

compartment. Use TYPE I (normal) tape only.

2 Press N.

To Press

stop playback xZ
fast-forward or rewind the tape M or m
pause playback X

eject the cassette xZ

Press the button again to resume play after pause.

Recording

1 Press xZ to open the tape compartment and insert a blank tape. Use TYPE I

(normal) tape only.

2 Select the program source you want to record.

To record from the CD player

Press x and load a CD (See “Playing a CD”).

To record from the radio

Press RADIO BAND•AUTO PRESET and tune in the station you want (See
“Listening to the radio”).

3 Press z to start recording.

(N is depressed automatically.)

To Press

stop recording xZ
pause recording X

Tips

• Adjusting the volume or the audio emphasis will not affect the recording level.

• If the AM program makes a whistling sound after you've pressed z in step 3, press MODE to select

the position of ISS (Interference Suppress Switch) that most decreases the noise.

• For the best results, use the AC power as a power source for recording.

• To erase a recording, proceed as follows:
1 Insert a tape with the recording you want to erase.
2 Press FUNCTION on the remote repeatedly until “TAPE” appears in the display.
3 Press z.

Press the button again to resume recording.

Using the remote control to operate a TV or
CBL

About presetting the remote

The remote is preset at the factory to operate Sony brand components.
If you’re using the remote with a Sony component, you won’t need to preset the remote before

you start using it.
To set up the remote to use with other (non-Sony) manufacturers’ components, or to use with a

component that is not preset at the factory, you’ll need to follow the instructions in this manual
to preset the remote with the correct code number for your components. (Also refer to the list
under “Component code numbers” on the front side.)

Component that can be preset Button Factory

TV TV Sony TV
Analog cable box CBL –

Notes

• Make sure that the TV•CD/RADIO switch on the remote is set to TV.

• The remote can be set up to operate only one component per button – unless their code numbers
happen to be the same. For example, you cannot set up the remote to operate a Sony TV and a
Panasonic TV simultaneously (because they use different code numbers).

• You may not be able to operate even a Sony brand component with the factory presetting. In such a
case, follow the procedure in “Setting the code.”

Setting the code

Follow the steps of “Entering the code number” and “Checking if the code number works”
below for each component you plan to use with the remote.

Entering the code number

1 See “Component code numbers”, and find the three-digit code number for the desired

component.
If more than one code number is listed, use the number that’s listed first to complete the steps

below.
For example, if you’re setting up a Philips’ TV, you would use the code number 011.
If your component isn’t listed, see “Searching for the correct code.”

2 While pressing SET, press POWER on the remote.
3 Press the button of the component that you want to set up (TV or CBL).
4 Enter the component’s code number. For example, if you’re entering the code for a Philips

TV, you would press 011.

5 Press and release ENT to store the code number in the remote’s memory.
6 Go to “Checking if the code number works” to finish setting up.

If you press a wrong button in step 4

Press POWER on the remote while pressing SET and then go back to step 3.

Checking if the code number works

1 Power on the component you want to set up.
2 Aim the remtoe at the component and press a button to check if that button works.

For example, press the POWER button to see if it works on your component .

3 Check that the other buttons of the remote is operating the corresponding functions of the

component.

If the remote doesn’t seem to be working...

• First, try repeating these setup procedures using the other codes listed for your component. (Refer to
the list under “Component code numbers” on the front side.)

• If – after trying all the codes listed for your component – you still cannot get the remote to work
properly, try the search method described in “Searching for the correct code.”

setting

Searching for the correct code

If you’ve tried all the code numbers listed for your component and you still cannot get the
remote to work (or if your component is not listed in the “Component code numbers” tables on
the front side), try these steps.

1 Power on the component you want to set up. Insert a tape or disc if necessary.
2 While pressing SET, press POWER.
3 Press the button of the component on the remote that you want to set up (TV or CBL).
4 Press and release TUNE/CH+. Then press and release POWER.
5 Repeat step 4 until the correct code number is found.

Each time you press TUNE/CH+ and then POWER, a new code number will be transmitted.
Keep trying until your component operates by receiving the transmitted signal from the

remote (e.g., the power turns off, the channel function works, playback starts, etc.) Be patient
as you do this; it may take about 70 tries until the correct code number is located.

6 When the correct code is found, press ENT to store the code number in the remote’s memory.
7 Check that the remote is operating the other functions of your component by pressing the

corresponding buttons on the remote. If they seem to be working properly, you’re done
setting up the remote.

If the component does not operate properly, repeat steps 1 to 6 and search for another code.

Operating a component

1 Press the button of the desired component on the remote (TV or CBL).
2 Point the remote directly at the component.
3 Press the button for the function you want to use.

To Press

adjust the volume on TV VOL + or –
mute the volume on TV MUTING
switch to the operations of each component TV or CBL on which that component is assigned
change the input mode on TV TV/VIDEO
change the channel TUNE/CH + or –

go back to the previous channel RECALL

Notes on using the remote control

Basically, use this remote in the same way as the remote supplied with your components.

• Using this remote will not increase the functions of your components. The functions of the remote are
limited to the functions of the components themselves. For example, if your TV does not have a
muting function, the MUTING button on this remote will not function with your TV.

• Some functions of the component may not work with this remote.

• If your cable box can control volume, be sure to set its volume switch to a medium position. If the
volume on the cable box is turned down completely, you will not be able to adjust your TV’s volume
with the remote.

• There may be cases you may turn on/off the cable box by pressing the TUNE/CH + or – button on the
remote.

Or use the number buttons and ENT, for example,
to change to channel 5, press 0 and 5 (and ENT).