3-251-115-31 (1)
2
FM/MW/LW
Compact Disc
Player
Installation/Connections
安裝線路連接
A
B
AUDIO OUT
FRONT
SUB OUT (MONO)
AUDIO OUT
REAR
BUS AUDIO IN
BUS CONTROL IN
CDX-M850MP
© 2003 Sony Corporation Printed in Korea
1
1
5
Equipment used in illustrations (not supplied)
插圖中的裝置（非附送）
Front speaker
前揚聲器
Rear speaker
後揚聲器
Power amplifier
功率放大器
23
6
4
7
CD/MD changer
CD/MD 換碟機
Active subwoofer
有源超低音揚聲器
Rotary commander RM-X4S
旋轉式控制器 RM-X4S
× 4
× 2
Source selector*
音源選擇器*
XA-C30
Cautions
•This unit is designed for negative earth 12 V
DC operation only.
•Do not get the wires under a screw, or caught
in moving parts (e.g., seat railing).
•Before making connections, turn the car
ignition off to avoid short circuits.
•Connect the yellow and red power input leads
only after all other leads have been connected.
•Run all earth wires to a common earth
point.
•Be sure to insulate any loose unconnected
wires with electrical tape for safety.
Notes on the power supply cord (yellow)
•When connecting this unit in combination with
other stereo components, the connected car
circuit’s rating must be higher than the sum of
each component’s fuse.
•When no car circuits are rated high enough,
connect the unit directly to the battery.
Parts Iist (1)
•The numbers in the list are keyed to those in
the instructions.
•The bracket 1 is attached to the unit before
shipping. Before mounting the unit, use the
release keys 7 to remove the bracket 1 from
the unit. For details, see “Removing the
bracket (4)” on the reverse side of the sheet.
• Keep the release keys 7 for future use as
they are also necessary if you remove the
unit from your car.
Caution
Handle the bracket 1 carefully to avoid injuring
your fingers.
1
Note
Before installing, make sure that the catches on
both sides of the bracket 1 are bent inwards 2 mm.
If the catches are straight or bent outwards, the unit
will not be installed securely and may spring out.
Catch
BUS AUDIO IN
BUS CONTROL IN
* not supplied
非附送
Connection example (2)
Notes (2-A)
• Be sure to connect the black earth lead cord
before connecting the amplifier.
• If you connect an optional power amplifier and do
not use the built-in amplifier, the beep sound will
be deactivated.
Tip (2-B-
For connecting two or more CD/MD changers, the
source selector XA-C30 (optional) is necessary.
)
Connection diagram (3)
1 To a metal surface of the car
First connect the black earth lead, then connect
the orange/white striped, yellow, and red power
input leads.
2 To the power aerial control lead or power
supply lead of aerial booster amplifier
Notes
• It is not necessary to connect this lead if there
is no power aerial or aerial booster, or with a
manually-operated telescopic aerial.
• When your car has a built-in FM/MW/LW aerial
in the rear/side glass, see “Notes on the control
and power supply leads.”
3 To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting
any other system may damage the unit.
4 To the interface cable of a car telephone
5 To a car’s illumination signal
Be sure to connect the black earth lead to a
metal surface of the car first.
6 To the +12 V power terminal which is energised
in the accessory position of the ignition key
switch
Notes
• If there is no accessory position, connect to the
+12 V power (battery) terminal which is
energised at all times.
Be sure to connect the black earth lead to a
metal surface of the car first.
• When your car has a built-in FM/MW/LW aerial
in the rear/side glass, see “Notes on the control
and power supply leads.”
7 To the +12 V power terminal which is energised
at all times
Be sure to connect the black earth lead to a
metal surface of the car first.
3
3
Left
左
Right
右
Left
左
3
from car aerial
來自汽車天線
1
*
SUB OUT (MONO)
*
AMP REM
Max. supply current 0.3 A
最大源電流 0.3 A
1
*
BUS AUDIO IN
/AUX IN
2
5
*
REMOTE IN
BUS
REAR FRONT
AUDIO IN
AUDIO OUT
AUX IN
AUDIO OUT
REAR
Blue/white striped
藍白條紋
White
白色
White/black striped
白黑條紋
Grey
灰色
Grey/black striped
灰黑條紋
Green
緣色
Green/black striped
緣黑條紋
3
*
AUDIO OUT
FRONT
L
R
Fuse (10 A)
保險絲（10 A）
4
*
Supplied with XA-C30
附帶於 XA-C30
BUS
CONTROL IN
6
Black
黑色
Blue
藍色
Light blue
淡藍色
Orange/white striped
橙白條紋
Red
紅色
Source selector
(not supplied)
音源選擇器
（非附送）
XA-C30
ANT REM
Max. supply current 0.1 A
最大源電流 0.1 A
ATT
ILLUMINATION
Supplied with the CD/MD changer
附帶於 CD/MD 換碟機
*1 RCA pin cord (not supplied)
RCA 針型插頭電線（非附送）
2
*
Insert with the cord upwards.
電線向上插入。
*3 Auxiliary optional equipment such
as portable DVD player (not
supplied)
輔助選購裝置，如便攜式 DVD 播放機
（非附送）
*4 supplied with the auxialiry
equipment
附帶於輔助裝置
*5Be sure to match the colour-
coded code for audio to the
appropriate jacks from the unit.
If you connect an optional CD/
1
2
MD unit, you cannot use AUX IN
terminal.
確保音頻色碼編碼與裝置上的正確插孔
相一致。
如果連接選購裝置 CD/MD 裝置，則不
能使用 AUX IN 端子。
4
5
6
Right
右
Notes on the control and power supply leads
• The power aerial control lead (blue) supplies +12 V
DC when you turn on the tuner or when you
activate the AF (Alternative Frequency), TA (Traffic
Announcement) function.
• When your car has built-in FM/MW/LW aerial in
the rear/side glass, connect the power aerial
control lead (blue) or the accessory power input
lead (red) to the power terminal of the existing
aerial booster. For details, consult your dealer.
• A power aerial without relay box cannot be used
with this unit.
Memory hold connection
When the yellow power input lead is connected,
power will always be supplied to the memory circuit
even when the ignition key is turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms ,
and with adequate power handling capacities to
avoid its damage.
• Do not connect the speaker terminals to the car
chassis, or connect the terminals of the right
speakers with those of the left speaker.
• Do not connect the earth lead of this unit to the
negative (–) terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active
speakers (with built-in amplifiers) to the speaker
terminals may damage the unit.
• To avoid a malfunction, do not use the built-in
speaker wires installed in your car if the unit shares
a common negative (–) lead for the right and left
speakers.
• Do not connect the unit’s speaker cords to each
other.
Note on connection
If speaker and amplifier are not connected correctly,
“Failure” appears in the display. In this case, make
sure the speaker and amplifier are connected
correctly.
Purple
紫色
Purple/black striped
紫黑條紋
注意
• 本機只能使用負極接地 12 V 直流電源。
• 不要使導線夾在螺栓下，或繞掛在移動部件上
（如：座椅扶手上）。
• 進行連接之前，請先關閉汽車的點火器，以避免
短路。
• 黃色和紅色電源輸入導線必須在所有其它導線都
連接完畢以後才連接。
• 將所有地線都連接到同一接地點。
• 為了安全，請確認把沒有連接的導線用電器膠帶
包紮進行絕緣。
電源導線須知（黃色）
• 將本機與其它立體聲裝置相連接時，所連接的
汽車電路容量必須大於每個裝置保險絲容量的
總和。
• 當汽車電路容量不夠大時，請將本機直接與電
池相連接。
零件一覽表（1）
• 圖示數字與說明書中的數字是一致的。
• 托架 1 在出廠之前已經裝在本裝置上。在安裝
本裝置之前，請先使用開鎖鑰匙 7 將托架 1
從本裝置上拆下。詳細說明，請參見本頁反面“拆
下保護環（4）”。
• 如果今後要將本裝置從汽車上拆下，也要使用開
鎖鑰匙，因此請保存好開鎖鑰匙 7 以備今後使
用。
注意
移動裝卸支架 1 時，請特別注意別傷到手指。
Yellow
黃色
線路連接圖例（2）
註
（2-A）
•
務必在接放大器之前連接黑色接地導線
•
如果您連接了選購的功率放大器而不使用內裝的放大
器，將無嘟聲功能
要領
（2-B- ）
若要連接 2 台或更多 CD/MD 換碟機時，必須使用音源選
擇器 XA-C30（選購件）。
。
線路連接圖（3）
1 連接至汽車的金屬表面
首先連接黑色接地導線，然後再連接橙白條紋，黃
色和紅色電源輸入導線。
2 連接至電動天線控制導線或天線升壓放大器的電源導
線
註
•
如無電動天線，天線升壓器，或有手動套管式天
線，便不須連接此導線。
•
您汽車的後側玻璃窗中如果有內置 FM/MW/LW 天
線，即請參看“控制線和電源線須知”。
3 連接至選購的功率放大器的 AMP REMOTE IN（放大器
遙控輸入）
本連接僅用於放大器。連接任何其它系統可能會損壞
本機。
4 連接至汽車電話的接口電纜
5 至汽車照明訊號
務請首先將黑色接地導線連接至汽車的金屬表面。
6 連接至在點火鑰匙開關的附件位置上通電的 +12 V
電源端子
註
•
若沒有附件位置，則請連接至始終通電的 +12 V 電
源（電池）端子。
必須首先將黑色接地導線連接至汽車的金屬表面。
•
您汽車的後側玻璃窗中如果有內置 FM/MW/LW 天
線，即請參看“控制線和電源線須知”。
7 連接至始終通電的 +12 V 電源端子
必須首先將黑色接地導線連接至汽車的金屬表面。
7
控制線和電源線須知
•
當您打開調諧器或啟動 AF（變換頻率）或 TA（交通公
告）功能時，電源天線控制導線（藍色）提供 +12 V 直
流電。
•
。
若您的汽車後側玻璃窗上有內置 FM/MW/LW 天線，
須將電動天線控制導線（藍色）或輔助電源輸入導線
（紅色）連接到現有天線升壓器上的電源端子上。詳
細內容請向銷售商諮詢。
•
本機不能使用不具備繼電器盒的電動天線。
保持記憶的線路連接法
當連接好黃色電源輸入導線時，即使汽車發動機點火鑰匙
關閉，電源仍將對記憶電路供電。
連接揚聲器時的注意事項
•
連接揚聲器電線以前，請先關閉本機電源。
•
使用阻抗為 4-8Ω 且具有足夠功率處理容量的揚聲
器，以免損壞揚聲器。
•
不要將揚聲器端子連接到車身上，或將右揚聲器端子
與左揚聲器端子相連接。
•
切勿將本機的接地導線連接至揚聲器的負(-)接線端。
•
揚聲器不可並聯連接。
•
請僅連接無源揚聲器。若將有源揚聲器（帶內置放大
器）連接到揚聲器端子上會損壞本機。
•
若本裝置使用左、右揚聲器的共用負極(-)導線，為了
避免故障，切勿使用已安裝在汽車內的內置揚聲器導
線。
•
請勿將本裝置揚聲器導線相互連接。
有關連接注意事項
如果未正確連接揚聲器和放大器，則顯示幕上會出現
“Failure”。此時，請正確連接揚聲器和放大器。
1
註
安裝之前，必須將托架
果拌鉤筆直或向外彎曲，則本裝置將無法牢固安裝，並可
能彈出。
拌鉤
1
兩側的拌鉤向內彎曲 2 mm。如
Loading...