Sony CDXFW-500, CDXF-5000 Service manual

CDX-F5000/FW500

SERVICE MANUAL

Ver. 1.2 2006. 05

• The tuner and CD sections have no adjustments.

AUDIO POWER SPECIFICATIONS

POWER OUTPUT AND TOTAL HARMONIC DISTORTION

23.2 watts per channel minimum continuous average power into 4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more than 5% total harmonic distortion.

SPECIFICATIONS

CD player section

Signal-to-noise ratio 120 dB Frequency response 10 – 20,000 Hz Wow and flutter Below measurable limit

Tuner section

Tuning range 87.5 – 107.9 MHz Antenna terminal External antenna connector Intermediate frequency 10.7 MHz/450 kHz Usable sensitivity 9 dBf Selectivity 75 dB at 400 kHz Signal-to-noise ratio 67 dB (stereo),

69 dB (mono)

Harmonic distortion at 1 kHz

0.5% (stereo),

0.3% (mono) Separation 35 dB at 1 kHz Frequency response 30 – 15,000 Hz

Tuning range 530 – 1,710 kHz Antenna terminal External antenna connector Intermediate frequency 10.7 MHz/450 kHz Sensitivity 30 µV

Power amplifier section

Outputs Speaker outputs

(sure seal connectors)

Speaker impedance 4 – 8 ohms Maximum power output 52 W × 4 (at 4 ohms)

US Model

CDX-F5000/FW500

Canadian Model

CDX-F5000

Model Name Using Similar Mechanism CDX-R3000/RW300 CD Drive Mechanism T ype MG-611XA-186//K Optical Pick-up Name KSS1000E

General

Outputs Audio outputs terminal (rear/sub switchable)

Power antenna relay control terminal Power amplifier control terminal

Inputs Telephone ATT control terminal

Remote controller input terminal BUS control input terminal BUS audio input terminal Antenna input terminal

Tone controls Low: ±10 dB at 60 Hz (XPLOD)

Mid: ±10 dB at 1 kHz (XPLOD) High: ±10 dB at 10 kHz (XPLOD)

Power requirements 12 V DC car battery

(negative ground)

Dimensions Approx. 178 × 50 × 177 mm

(7 1/8 × 2 × 7 in.) (w/h/d)

Mounting dimensions Approx. 182 × 53 × 161 mm

(7 1/4 × 2 1/8 × 6 3/8 in.) (w/h/d)

Mass Approx. 1.2 kg

(2 lb. 10 oz.)

Supplied accessories Parts for installation and connections (1 set)

Front panel case (1) Card remote commander RM-X115

Design and specifications are subject to change without notice.

9-961-429-03

FM/AM COMPACT DISC PLAYER

Sony Corporation

eVehicle Division Published by Sony Techno Create Corporation

CDX-F5000/FW500

SERVICE NOTES

NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT

The laser diode in the optical pick-up block may suffer electrostatic breakdown because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic breakdown and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care.

NOTES ON LASER DIODE EMISSION CHECK

The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens.

Notes on Chip Component Replacement

• Never reuse a disconnected chip component.

• Notice that the minus side of a tantalum capacitor may be dam-

aged by heat.

TEST DISCS

This set can playback CD-R and CD-ROM discs. The following test discs should be used to check the capability:

CAUTION

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

If the optical pick-up block is defective, please replace the whole optical pick-up block. Never turn the semi-fixed resistor located at the side of optical pick-up block.

optical pick-up

CD-R test disc TCD-R082LMT (Part No. J-2502-063-1) CD-RW test disc TCD-W082L (Part No. J-2502-063-2)

semi-fixed resistor

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

ATTENTION AU COMPOSANT AYANT RAPPORT

À LA SÉCURITÉ!!

LES COMPOSANTS IDENTIFIÉS P AR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT . NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.

CDX-F5000/FW500

Notes on CD-Rs (recordable CDs)/CD-RWs (rewritable CDs)

This unit can play the following discs:

Type of discs Label on the disc

Audio CD

MP3 files

• Some CD-Rs/CD-RWs (depending on the equipment used for

its recording or the condition of the disc) may not play on this unit.

• You cannot play a CD-R/CD-RW that is not finalized∗.

• You can play MP3 files recorded on CD-ROMs, CD-Rs, and

CD-RWs.

• A CD-R/CD-RW to which a session can be added can be played.

UNLEADED SOLDER

Boards requiring use of unleaded solder are printed with the lead free mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.)

: LEAD FREE MARK

Unleaded solder has the following characteristics.

• Unleaded solder melts at a temperature about 40°C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350°C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful!

• Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc.

• Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder.

∗ A process necessary for a recorded CD-R/CD-RW disc to be

played on the audio CD player.

EXTENSION CABLE AND SERVICE POSITION

When repairing or servicing this set, connect the jig (extension cable) as shown below.

• Connect the MAIN board (CN751) and the SERVO board (CN1) with the extension cable (Part No. J-2502-076-1).

MAIN BOARD CN751

J-2502-076-1

SERVO BOAR CN1

CDX-F5000/FW500

1. GENERAL

Location of Controls (CDX-F5000) ........................................ 5

Location of Controls (CDX-FW500) ...................................... 5

Connections (CDX-F5000) ..................................................... 6

Connections (CDX-FW500).................................................... 7

2. DISASSEMBLY

2-1. Sub Panel Assy (CD)........................................................... 9

2-2. CD Mechanism Block ......................................................... 9

2-3. Main Board ....................................................................... 10

2-4. Chassis (T) Sub Assy ........................................................ 10

2-5. Roller Arm Assy ................................................................ 11

2-6. Chassis (OP) Assy.............................................................11

2-7. Optical Pick-up ................................................................. 12

2-8. SL Motor Assy (M902) .....................................................12

2-9. LE Motor Assy (M903)..................................................... 13

2-10. Servo Board....................................................................... 13

3. DIAGRAMS

3-1. IC Pin Descriptions ........................................................... 14

3-2. Block Diagram –CD Section–........................................... 18

3-3. Block Diagram –Main Section–........................................19

3-4. Block Diagram –Display Section–....................................20

3-5. Circuit Boards Location .................................................... 20

3-6. Note for Printed Wiring Boards and

Schematic Diagrams ..........................................................21

3-7. Waveforms......................................................................... 21

3-8. Printed Wiring Boards –CD Mechanism Section–............ 22

3-9. Schematic Diagram –CD Mechanism Section– ................23

3-10. Schematic Diagram –Main Section (1/2)– ........................24

3-11. Schematic Diagram –Main Section (2/2)– ........................25

3-12. Printed Wiring Boards –Main Section– ............................ 26

3-13. Printed Wiring Board –Relay Section– ............................. 27

3-14. Schematic Diagram –Relay Section–................................27

3-15. Printed Wiring Board –Display Section– .......................... 28

3-16. Schematic Diagram –Display Section–............................. 29

3-17. IC Block Diagrams............................................................ 30

4. EXPLODED VIEWS

4-1. Main Section ..................................................................... 31

4-2. Front Panel Section ........................................................... 32

4-3. CD Mechanism Section (1) ...............................................33

4-4. CD Mechanism Section (2) ...............................................34

4-5. CD Mechanism Section (3) ...............................................35

4-6. CD Mechanism Section (4) ...............................................36

5. ELECTRICAL PARTS LIST ........................................ 37

SECTION 1

GENERAL

CDX-F5000/FW500

This section is extracted from instruction manual.

Location of controls

(CDX-F5000) (CDX-FW500)

Refer to the pages listed for details.

8, 10

12, 13, 15

BTMSENS

DSO

SEEK SEEK

EQ3

a DSO button b SOURCE (Power on/Radio/CD/MD)

button

To s el ect the source.

c LIST/CAT* d Receptor for the card remote

e Display window f Z (eject) button (located on the front side

g OPEN button h EQ3 button i MODE button

j Volume co ntrol dial/Select button

k DSPL (display mode change) button

button

commander

of the unit, behind the front panel)

To c hange operation.

Rotate to: – Adjust the volume. – Adjust settings. Press to: – Select items.

11, 13, 18

BBESHUFREP

CDX-F5000

l SENS button m RESET button (located on the front side of

the unit, behind the front panel)

n BTM button o Number buttons

Radio: To s t or e stations /r eceive store d stati on s. CD/MD:

(3): REP (4): SHUF

p OFF (Stop/Power off) button*

*1 (CAT)

is available only when the XM tuner is

connected.

Warning when installing in a car without an ACC (accessory) position on the ignition switch

er turning off the ignition, be sure to press

Aft

(OFF)

and hold disappears.

Otherwise, the display does not turn off and this causes battery drain.

6543

OFF

14, 15

on the unit until the display

OPEN

Location of controls

Refer to the pages listed for details.

8, 10

12, 13, 15

BTMSENS

CDX-FW500

l SENS button m RESET button (located on the front side of

the unit, behind the front panel)

n BTM button o Number buttons

Radio: To s t or e stations /r eceive store d stati on s. CD/MD:

(3): REP

(4): SHUF

p OFF (Stop/Power off) button*

*1 (CAT)

connected.

Warning when installing in a car without an ACC (accessory) position on the ignition switch

er turning off the ignition, be sure to press

Aft and hold disappears.

Otherwise, the display does not turn off and this causes battery drain.

BBESHUFREP

14, 15

is available only when the XM tuner is

(OFF)

on the unit until the display

DSO

SEEK SEEK

EQ3

a DSO button

b SOURCE (Power on/Radio/CD/MD)

button

To s el ect the source.

c LIST/CAT* d Receptor for the card remote

e Display window f Z (eject) button (located on the front side

g OPEN button h EQ3 button i MODE button

j Volume co ntrol dial/Select button

k DSPL (display mode change) button

button

commander

of the unit, behind the front panel)

To c hange operation.

Rotate to: – Adjust the volume. – Adjust settings. Press to: – Select items.

11, 13, 18

OPEN

6543

OFF

DSO

SEEK SEEK

EQ3

(DISC/PRESET)

(+): to select upwards

(SEEK)

(–): to select

q DISC (ALBUM)/PRESET buttons (+/–)

To r e ce ive preset stations/change the disc* skip albums*

*1 *2

r SEEK buttons (–/+)

To s k ip tracks/fast-forward, reverse a track/ tune in stations automatically, find a station manually/select a setting.

leftwards/

(DISC/PRESET)

(–): to select downwards

When an optional CD/MD unit is connected. Available only when an optional CD unit with the MP3 file control function is connected, and MP3 file is played.

SENS

(SEEK)

SEEK

(+): to select

rightwards/

Card remote commander RM-X115

DSPL MODE

PRESET

SOURCE

–

SEEK

PRESET

–

VOL

–

The corresponding buttons of the card remote commander control the same functions as those on this unit.

a DSPL button b SOURCE button c SEEK (–/+) buttons d OFF button

e VOL (+/–) buttons f MODE button g PRESE

T (DISC/ALBUM) (+/–) buttons

h AT T b u tt o n

Note

If the display disappears by pressing be operated with the card remote commander unless

(SOURCE)

on the unit is pressed, or a di sc i s in se rted

to activate the unit first.

Tip

For details on how to replace the battery, see “Replacing the lithium battery” on page 21.

continue to next page t

SEEK

AT TOFF

(OFF)

, it cannot

CDX-F5000/FW500

Connections (CDX-F5000)

from car antenna à partir de l’antenne de la voiture

Left Gauche

Right Droit

Left Gauche

Right Droit

CDX-F5500 only CDX-F5500 uniquement

BUS AUDIO IN

AMP REM

Max. supply current 0.3 A Courant max. fourni 0,3 A

AUDIO OUT

REAR

Blue/white striped Rayé bleu/blanc

White Blanc

White/black striped Rayé blanc/noir

Gray Gris

Gray/black striped Rayé gris/noir

Green Vert

Green/black striped Rayé vert/noir

Purple Mauve

Purple/black striped Rayé mauve/noir

AUDIO OUT

FRONT

Fuse (10 A) Fusible (10 A)

Supplied with XA-C30 Fourni avec le XA-C30

REMOTE

BUS

CONTROL IN

Black Noir

Blue Bleu

Light blue Bleu ciel

Red Rouge

Yellow Jaune

Max. supply current 0.1 A

Courant max. fourni 0,1 A

ANT REM

Source selector

(not supplied)

Sélecteur de source

(non fourni)

XA-C30

ATT

Supplied with the CD/MD changer Fourni avec le changeur de CD/MD

RCA pin cord (not supplied)

AUDIO OUT can be switched to REAR or SUB.

For details, see the supplied operating instructions.

Insert with the cord upwards.

Cordon à broche RCA (non fourni)

AUDIO OUT peut être commuté sur

REAR ou SUB.

Pour obtenir plus de détails, reportezvous au mode d'emploi fourni.

Insérez avec le câble vers le bas.

Connection diagram (3)

To a metal surface of the car

First connect the black ground lead, then connect the yellow and red power input leads.

To the power antenna control lead or power supply lead of antenna booster amplifier

Notes

• It is not necessar y to connect this lead if there is no power antenna or antenna booster, or with a manually-operated telescopic antenna.

• When your car has a built-in FM/AM antenna in the rear/side glass, see “Notes on the control and power supply leads.”

To AMP REMOTE IN of an optional power amplifier

This connection is only for amplifiers. Connecting any other system may damage the unit.

To the interface cable of a car telephone

To the +12 V power terminal which is energized in the accessory position of the ignition key switch

Notes

• If there is no accessory position, connect to the +12 V power (battery) terminal which is energized at all times. Be sure to connect the black ground lead to a metal surface of the car first.

• When your car has a built-in FM/AM antenna in the rear/side glass, see “Notes on the control and power supply leads.”

To the +12 V power terminal which is energized at all times

Be sure to connect the black ground lead to a metal surface of the car first.

Notes on the control and power supply leads

• The power antenna control lead (blue) supplies +12 V DC when you turn on the tuner.

• When your car has built-in FM/AM antenna in the rear/side glass, connect the power antenna control lead (blue) or the accessory power input lead (red) to the power terminal of the existing antenna booster. For details, consult your dealer.

•A power antenna without a relay box cannot be used with this unit.

Memory hold connection

When the yellow power input lead is connected, power will always be supplied to the memory circuit even when the ignition switch is turned off.

Notes on speaker connection

• Before connecting the speakers, turn the unit off.

• Use speakers with an impedance of 4 to 8 ohms, and with adequate power handling capacities to avoid its damage.

• Do not connect the speaker terminals to the car chassis, or connect the terminals of the r ight speakers with those of the left speaker.

• Do not connect the ground lead of this unit to the negative (–) terminal of the speaker.

• Do not attempt to connect the speakers in parallel.

• Connect only passive speakers. Connecting active speakers (with built-in amplifiers) to the speak er terminals may damage the unit.

•To avoid a malfunction, do not use the built-in speaker leads installed in your car if the unit shares a common negative (–) lead for the right and left speakers.

• Do not connect the unit’s speaker leads to each other.

Note on connection

If speaker and amplifier are not connected correctly, “FAILURE” appears in the display. In this case, make sure the speaker and amplifier are connected correctly.

Schéma de raccordement (3)

À un point métallique de la voiture

Branchez d‘abord le fil de masse noir et, ensuite, les fils d‘entrée d‘alimentation jaune et rouge.

Vers le fil de commande de l‘antenne électrique ou le fil d‘alimentation de l‘amplificateur d‘antenne

Remarques

•Il n'est pas nécessaire de raccorder ce fil s'il n'y a pas d'antenne électrique ni d'amplificateur d'antenne, ou avec une antenne télescopique manuelle.

•Si votre voiture est équipée d'une antenne FM/ AM intégrée dans la vitre arrière/latérale, voir « Remarques sur les fils de commande et d'alimentation ».

Au niveau du AMP REMOTE IN de l’amplificateur de puissance en option

Ce raccordement s’applique uniquement aux amplificateurs. Le branchement de tout autre système risque d’endommager l’appareil.

Vers le cordon de liaison d’un téléphone de voiture

À la borne +12 V qui est alimentée quand la clé de contact est sur la position accessoires

Remarques

•S'il n'y a pas de position accessoires, raccordez la borne d'alimentation (batterie) +12 V qui est alimentée en permanence. Raccordez d’abord le fil de masse noir à un point métallique du véhicule.

•Si votre voiture est équipée d'une antenne FM/ AM intégrée dans la vitre arrière/latérale, voir « Remarques sur les fils de commande et d'alimentation ».

À la borne +12 V qui est alimentée en permanence

Raccordez d’abord le fil de masse noir à un point métallique du véhicule.

Remarques sur les fils de commande et d

’

alimentation

• Le fil de commande de l’antenne électrique (bleu) fournit une alimentation de +12 V CC lorsque vous mettez la radio sous tension.

• Lorsque votre voiture est équipée d’une antenne FM/AM intégrée dans la vitre arrière/latérale, raccordez le fil de commande de l’antenne (bleu) ou l’entrée d’alimentation des accessoires (rouge) à la borne d’alimentation de l’amplificateur d’antenne existant. Pour plus de détails, consultez votre détaillant.

• Une antenne électrique sans boîtier de relais ne peut pas être utilisée avec cet appareil.

Raccordement pour la conservation de la mémoire

Lorsque le fil d’entrée d’alimentation jaune est raccordé, le circuit de la mémoire est alimenté en permanence même si la clé de contact est sur la position d’arrêt.

Remarques sur le raccordement des haut-parleurs

•Avant de raccorder les haut-parleurs, mettez l’appareil hors tension.

• Utilisez des haut-parleurs ayant une impédance de 4 à 8 ohms avec une capacité électrique adéquate pour éviter de les endommager.

• Ne raccordez pas les bornes du système de hautparleurs au châssis de la voiture et ne raccordez pas les bornes des haut-parleurs droit à celles du hautparleur gauche.

• Ne raccordez pas le câble de masse de cet appareil à la borne négative (–) de l’enceinte.

•N’essa yez pas de raccorder les haut-parleurs en parallèle.

• Raccordez uniquement des haut-parleurs passifs. Le raccordement de haut-parleurs actifs (avec amplificateurs intégrés) aux bornes des hautparleurs peut endommager l’appareil.

•Pour éviter tout dysfonctionnement, n’utilisez pas les fils des haut-parleurs intégrés installés dans votre voiture si l’appareil par tage un fil négatif commun (–) pour les haut-parleurs droit et gauche.

• Ne raccordez pas entre eux les cordons des hautparleurs de l’appareil.

Remarque sur le raccordement

Si les haut-parleurs et l’amplificateur ne sont pas raccordés correctement, le message « FAILURE » s’affiche. Dans ce cas, assurez-vous que les hautparleurs et l’amplificateur sont bien raccordés.

Connections (CDX-FW500)

CDX-F5000/FW500

Left Izquierdo

Right Derecho

Left Izquierdo

Right Derecho

CDX-FW550 only sólo CDX-FW550

BUS AUDIO IN

from car antenna de la antena del automóvil

AUDIO OUT

REAR

Blue/white striped

AMP REM

Max. supply current 0.3 A Corriente máx. de alimentación de 0,3 A

Con raya azul/blanca

White Blanco

White/black striped Con raya blanca/negra

Gray Gris

Gray/black striped Con raya gris/negra

Green Verde

Green/black striped Con raya verde/negra

Purple Violeta

Purple/black striped Con raya violeta/negra

Fuse (10 A)

Fusible (10 A)

FRONT

Supplied with XA-C30 Suministrado con el XA-C30

REMOTE

BUS

CONTROL IN

Black Negro

Blue Azul

Light blue Azul celeste

Red Rojo

Yellow Amarillo

Max. supply current 0.1 A

Corriente máx. de alimentación de 0,1 A

ANT REM

Source selector

(not supplied) Selector de fuente (no suministrado )

XA-C30

ATT

Supplied with the CD/MD changer Suministrado con el cambiador de CD/MD

RCA pin cord (not supplied)

AUDIO OUT can be switched to REAR or SUB.

For details, see the supplied operating instructions.

Insert with the cord upwards.

Cable con terminales RCA (no suministrado)

AUDIO OUT (Salida de audio) puede cambiarse a REAR (P osterior) o SUB (Secundaria).

Para obtener información, consulte el manual de instrucciones suministrado.

Insertar con el cable hacia arriba.

Connection diagram (3)

To a metal surface of the car

First connect the black ground lead, then connect the yellow and red power input leads.

To the power antenna control lead or power supply lead of antenna booster amplifier

Notes

• It is not necessar y to connect this lead if there is no power antenna or antenna booster, or with a manually-operated telescopic antenna.

• When your car has a built-in FM/AM antenna in the rear/side glass, see “Notes on the control and power supply leads.”

To AMP REMOTE IN of an optional power amplifier

This connection is only for amplifiers. Connecting any other system may damage the unit.

To the interface cable of a car telephone

To the +12 V power terminal which is energized in the accessory position of the ignition key switch

Notes

• If there is no accessory position, connect to the +12 V power (battery) terminal which is energized at all times. Be sure to connect the black ground lead to a metal surface of the car first.

• When your car has a built-in FM/AM antenna in the rear/side glass, see “Notes on the control and power supply leads.”

To the +12 V power terminal which is energized at all times

Be sure to connect the black ground lead to a metal surface of the car first.

Notes on the control and power supply leads

• The power antenna control lead (blue) supplies +12 V DC when you turn on the tuner.

•A power antenna without a relay box cannot be used with this unit.

Memory hold connection

When the yellow power input lead is connected, power will always be supplied to the memory circuit even when the ignition switch is turned off.

Notes on speaker connection

• Before connecting the speakers, tur n the unit off.

• Use speakers with an impedance of 4 to 8 ohms, and with adequate power handling capacities to avoid its damage.

• Do not connect the speaker terminals to the car chassis, or connect the terminals of the right speakers with those of the left speaker.

• Do not connect the ground lead of this unit to the negative (–) terminal of the speaker.

• Do not attempt to connect the speakers in parallel.

• Connect only passive speakers. Connecting active speakers (with built-in amplifiers) to the speak er terminals may damage the unit.

•To avoid a malfunction, do not use the built-in speaker leads installed in your car if the unit shares a common negative (–) lead for the right and left speakers.

• Do not connect the unit’s speaker leads to each other.

Note on connection

If speaker and amplifier are not connected correctly, “FAILURE” appears in the display. In this case, make sure the speaker and amplifier are connected correctly.

Diagrama de conexión (3)

A una superficie metálica del automóvil

Conecte primero el cable de toma a tierra negro, y después los cables amarillo y rojo de entrada de alimentación.

Al cable de control de la antena motorizada o al cable de fuente de alimentación del amplificador de antena

Notas

•Si no se dispone de antena motorizada ni de amplificador de antena, o se utiliza una antena telescópica accionada manualmente, no será necesario conectar este cable.

•Si el automóvil incorpora una antena de FM/ AM en el cr istal trasero o lateral, consulte “Notas sobre los cables de control y de fuente de alimentación”

Para conectar a AMP REMOTE IN del amplificador de potencia opcional

Esta conexión es sólo para amplificadores. La conexión de cualquier otro sistema puede dañar la unidad.

Al cable de interfaz de un teléfono para automóvil

Al terminal de alimentación de +12 V que recibe energía en la posición de accesorio del interruptor de la llave de encendido

Notas

• Si no hay posición de accesorio, conéctelo al terminal de alimentación (batería) de +12 V que recibe energía sin interrupción. Asegúrese de conectar primero el cable de toma a tierra negro a una superficie metálica del automóvil.

•Si el automóvil incorpora una antena de FM/AM en el cristal trasero o lateral, consulte “Notas sobre los cables de control y de fuente de alimentación”.

Al terminal de alimentación de +12 V que recibe energía sin interrupción

Asegúrese de conectar primero el cable de toma a tierra negro a una superficie metálica del automóvil.

Notas sobre los cables de control y de fuente de alimentación

•El cable de control de la antena motorizada (azul) suministrará cc de +12V cuando conecte la alimentación del sintonizador.

•Si el automóvil dispone de una antena de FM/AM incorporada en el cristal trasero o lateral, conecte el cable de control de antena motorizada (azul) o el cable de entrada de alimentación auxiliar (rojo) al terminal de alimentación del amplificador de antena existente. Para obtener más información, consulte a su proveedor.

• Con esta unidad no es posible utilizar una antena motorizada sin caja de relé.

Conexión para protección de la memoria

Si conecta el conductor de entrada amarillo, el circuito de la memoria recibirá siempre alimentación, aunque apague la llave de encendido.

Notas sobre la conexión de los altavoces

• Antes de conectar los altavoces, desconecte la alimentación de la unidad.

•Utilice altavoces con una impedancia de 4 a 8 con la capacidad de potencia adecuada para evitar que se dañen.

• No conecte los terminales de altavoz al chasis del automóvil, ni conecte los terminales del altavoz derecho con los del izquierdo.

• No conecte el cable de toma a tierra de esta unidad al ter minal negativo (–) del altavoz.

• No intente conectar los altavoces en paralelo.

• Conecte solamente altavoces pasivos. Si conecta altavoces activos (con amplificadores incorporados) a los terminales de altavoz, puede dañar la unidad.

•Par a evitar fallos de funcionamiento, no utilice los cables de altavoz incorporados instalados en el automóvil si su unidad comparte un cable negativo común (–) para los altavoces derecho e izquierdo.

• No conecte los cables de altavoz de la unidad entre sí.

Nota sobre la conexión

Si el altavoz y el amplificador no están conectados correctamente, aparecerá “FAILURE” en la pantalla. Si es así, compruebe la conexión de ambos dispositivos.

Ω

CDX-F5000/FW500

SECTION 2

DISASSEMBLY

Note : This set can be disassemble according to the following sequence.

SET

2-1. SUB PANEL ASSY (CD)

(Page 9)

2-2. CD MECHANISM BLOCK

(Page 9)

2-3. MAIN BOARD

(Page 10)

2-7. OPTICAL PICK-UP

(Page 12)

2-4. CHASSIS (T) SUB ASSY

(Page 10)

2-5. ROLLER ARM ASSY

(Page 11)

2-6. CHASSIS (OP) ASSY

(Page 11)

2-8. SL MOTOR ASSY (M902)

(Page 12)

2-10. SERVO BOARD

(Page 13)

2-9. LE MOTOR ASSY (M903)

(Page 13)

Note : Follow the disassembly procedure in the numerical order given.

)

2-1. SUB PANEL ASSY (CD)

two claws

CDX-F5000/FW500

two claw

two

screws

(+PTT 2.6

2-2. CD MECHANISM BLOCK

CD mechanism block

sub panel assy (CD)

bracket (CD)

CNP802

two

screws

(+PTT 2.6

screw

(+PTT 2.6

CN751

screw

(+PTT 2.6

CDX-F5000/FW500

)

2-3. MAIN BOARD

three screws

(+BTT)

MAIN board

two

screws

(+PTT 2.6

2-4. CHASSIS (T) SUB ASSY

two

screws

(+P 1.7

SENSOR board

claw

2.2)

claw

two

screws

(+P 1.7

2.2)

chassis (T) sub assy

2-5. ROLLER ARM ASSY

)

worm wheel (RA)

spring (RAL)

washer (1.1 – 2.5)

roller arm assy

spring (RAR)

CDX-F5000/FW500

2-6. CHASSIS (OP) ASSY

compression spring (damper)

washer

gear (LE1)

lever (D)

chassis (OP) assy

CN2

two compression springs (damper

slider (R)

Remove the six solderings.

tension coil spring (KF)

CDX-F5000/FW500

2-7. OPTICAL PICK-UP

claw

chucking arm sub assy

tension coil spring (CHKG)

optical pick-up

2-8. SL MOTOR ASSY (M902)

main shaft

rack (SL)

screw

(+B 1.4

SL motor assy (M902)

screw

(+P 1.4

1.8)

2-9. LE MOTOR ASSY (M903)

two toothed lock

(+M 1.4

bracket (LEM)

(+M 1.7

screw

)

screws

2.5)

screw

(+P 1.7

2.2)

screw

(+M 1.7

(M903)

woam (LEB) assy

2.5)

LE motor assy

leaf spring (LE)

screw

(+M 1.7

bearing (LEB)

washer

gear (LE1)

lever (D)

CDX-F5000/FW500

2.5)

slider (R)

2-10. SERVO BOARD

Remove the eight solderings.

Remove the soldering.

SERVO board

Remove the three solderings.

toothed lock

(M 1.7)

screw

claw

CN2

CDX-F5000/FW500

SECTION 3

DIAGRAMS

3-1. IC PIN DESCRIPTIONS

• IC1 µPD63712GC-8EU-A (RF AMP, DIGITAL SERVO, DIGITAL SIGNAL PROCESSOR) (SERVO BOARD)

Pin No. Pin Name I/O Pin Description

1LDOLaser diode ON/OFF control signal output (L: laser OFF , H: laser ON) 2PDIDimmer monitor input from optical pick-up laser diode. 3PNINot used. (Fixed at L in this set) 4AVDD — Analog power supply pin (+3.3 V) 5 DGND — Ground 6 RFOK O RFOK signal output to system control IC. 7 INTQ O CD text pack synchronization signal output to system control IC. 8RST I CD reset signal input from system control IC.

9A0I

10 STB I Data strobe signal input from system control IC. 11 SCK I Serial clock input from system control IC. 12 SO O Serial data output to system control IC. 13 SI I Serial data input from system control IC. 14 DVDD — Power supply pin (+3.3 V) 15 DAVDD — D/A converter power supply (+) pin (+3.3 V) 16 ROUT O Analog audio signal output (R-ch) 17 DAGND — Ground 18 REGC — Capacitor connection pin for SCF regulator. 19 DAGND — Ground 20 LOUT O Analog audio signal output (L-ch) 21 DAVDD — D/A converter power supply (+) pin (+3.3 V) 22 XVDD — Power supply pin (+3.3 V) 23 XTAL O Main system clock output (16.9344 MHz) 24 XTAL I Main system clock input (16.9344 MHz) 25 XGND — Ground 26 DVDD — Power supply pin (+3.3 V) 27 C1D1/FZD O Not used. (Open) 28 C1D2/TZD O Not used. (Open) 29 C2D1/RMUTE O CD R-ch data zero detection signal output 30 C2D2/LMUTE O CD L-ch data zero detection signal output 31 C2D3/SHOCK/SBSY O Not used. (Open) 32 LOCK/FR O Not used. (Open) 33 WFCK/MIRR O Not used. (Open) 34 RFCK/HOLD O Not used. (Open) 35 PLCK O Not used. (Open) 36 C16M O Not used. (Open) 37 DGND — Ground 38 TX O Not used. (Open) 39 EMPH/RAMOVER O Not used. (Open) 40 FLAG O Not used. (Open) 41 DVDD — Power supply pin (+3.3 V) 42 LIMIT I Not used. (Fixed at L in this set)

43 XTALEN I 44 DGND — Ground

45 DIN I Not used. (Connect to DOUT in this set) 46 DOUT O Not used. (Connect to DIN in this set) 47 SCKIN I Not used. (Connect to SCKO in this set) 48 SCKO O Not used. (Connect to SCKIN in this set) 49 LRCKIN I Not used. (Connect to LRCK in this set)

Command/parameter discrimination signal input from system control IC. (L: command transmission, H: parameter transmission)

Oscillation circuit ON/OFF control signal input (L: ON, H: OFF) (Fixed at L in this set)

+ 30 hidden pages

Sony CDXFW-500, CDXF-5000 Service manual

Specifications and Main Features

Frequently Asked Questions

User Manual

TABLE OF CONTENTS

GENERAL

Connections (CDX-F5000)

Connections (CDX-FW500)

DISASSEMBLY

CD mechanism block

sub panel assy (CD)

MAIN board

chassis (T) sub assy

roller arm assy

chassis (OP) assy

optical pick-up

SL motor assy (M902)

SERVO board

DIAGRAMS