Sony CCD-TRV77E, CCD-TRV66E Service Manual

Download

Page 1

CCD-TRV66E/TRV77E

RMT-708/717

SERVICE MANUAL

Ver 1.0 1999.01

Photo: CCD-TRV77E

RMT-717

Note : Specifications of CCD-TRV66E are described.

SPECIFICATIONS

AEP Model

CCD-TRV66E/TRV77E

UK Model

E Model

Hong Kong Model

Australian Model

Chinese Model

East European Model

North European Model

Russian Model

CCD-TRV66E

B501 MECHANISM

For MECHANISM ADJUSTMENT , refer to the “8mm Video MECHANICAL ADJUSTMENT MANUAL

” (9-973-801-11).

MICROFILM

VIDEO CAMERA RECORDER

Page 2

Table for difference of function

Model Destination

AEP1, AEP2, UK,

EE, NE, RU Remote Commander Lens Optical

Digital VTR REC Video Light Intelligent Accessory Shoe Time Code

Note : AEP2, UK model is 80×.

RMT-708 20× 360× (Note)

✕ ✕

Supplied accessories

CCD-TR V66E

E, HK, AUS, CN

RMT-708 20× 360×

✕ ✕

CCD-TRV77E

AEP

RMT-717 20× 80×

✕ ✕

1 Wireless Remote Commander (1)

2 AC-L10A/L10B/L10C AC power adaptor (1),

3 NP-F330 battery pack (1) 4 CR2025 lithium battery (1)

5 R6 (size AA) battery for Remote

6 A/V connecting cable (1) 7 Shoulder strap (1) 8 2-pin conversion adaptor (1)

9 21-pin conversion connector (1)

Remark

® : With FK-8500 block S005, S007 ® : With VL-23 board

® : With VC-214 board (4/10) IC701

RMT-708 : CCD-TRV66E RMT-717 : CCD-TRV77E

Mains lead (1)

The lithium battery is already installed in your camcorder.

Commander (2)

CCD-TRV66E : E, HK

CCD-TRV66E : AEP , EE, NE, RU , UK/CCD-TR V77E

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK ! OR DO TTED LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

SAFETY CHECK-OUT

After correcting the original service problem, perform the following safety checks before releasing the set to the customer.

1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges.

2. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors.

3. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair . Point them out to the customer and recommend their replacement.

• Abbreviation HK : Hong Kong Model AUS : Australian Model CN : Chinese Model EE : East European Model NE : North European Model RU : Russian Model

4. Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement.

5. Check the B+ voltage to see it is at the values specified.

6. Flexible Circuit Board Repairing

• Keep the temperature of the soldering iron around 270˚C during repairing.

• Do not touch the soldering iron on the same conductor of the circuit board (within 3 times).

• Be careful not to apply force on the conductor when soldering or unsoldering.

— 2 —

Page 3

SERVICE NOTE

1. POWER SUPPLY DURING REPAIRS ····························· 6

2. TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT) ································································6

SELF-DIAGNOSIS FUNCTION

1. Self-diagnosis Function ······················································7

2. Self-diagnosis Display························································ 7

3. Service Mode Display ························································ 7

3-1. Display Method ·································································· 7 3-2. Switching of Backup No. ··················································· 7 3-3. End of Display···································································· 7

4. Self-diagnosis Code Table ·················································· 8

1. GENERAL

Checking supplied accessories ··················································1-1 Quick Start Guide ······································································1-1

1. Connecting the mains lead················································· 1-1

2. Inserting a cassette ·····························································1-1

3. Recording a picture···························································· 1-1

4. Monitoring the playback picture on the LCD screen·········1-1

Getting Started··········································································· 1-1

Using this manual ··································································1-1 Step 1 Preparing the power supply ········································1-2 Step 2 Inserting a cassette······················································1-3

Recording – Basics ····································································1-4

Recording a picture································································ 1-4 Checking the recording – END SEARCH/EDITSEARCH/Rec Review····················· 1-6

Playback – Basics ······································································1-8

Playing back a tape ································································1-7 Viewing the recording on TV ················································1-7

Advanced Recording Operations···············································1-8

Photo recording······································································1-8 Using the wide mode ·····························································1-9 Using the fader function ························································ 1-9 Using special effects – Picture effect···································1-10 Using special effects – Digital effect··································· 1-10 Using the PROGRAM AE function ·····································1-11 Adjusting the exposure manually ········································1-12 Focusing manually······························································· 1-12 Superimposing a title ···························································1-13 Making your own titles ························································1-13 Using the built-in light························································· 1-14

Advanced Playback Operations···············································1-15

Playing back a tape with digital effects ·······························1-15

Editing on Other Equipment····················································1-15

Dubbing a tape ·····································································1-15 Recording video or TV programmes ···································1-16

Customizing Y our Camcorder ·················································1-16

Changing the MENU settings ··············································1-16 Resetting the date and time·················································· 1-18

Additional Information ····························································1-18

Usable cassettes and playback modes··································1-18 Changing the lithium battery in your camcorder ·················1-19 Troubleshooting ···································································1-19 Self-diagnosis display ··························································1-20 Warning indicators and messages ········································1-20 Using your camcorder abroad··············································1-21 Maintenance information and precautions···························1-21

Quick Reference ······································································1-22

Identifying the parts and controls ········································1-22 Quick function guide ··························································· 1-24

2. DISASSEMBLY

2-1. LCD Unit, PD-105 Board················································2-2 2-2. Cabinet (R) Assembly (TRV66E), (TRV77E)·················2-3

2-3. Mechanism Deck ·····························································2-4 2-4. EVF Block, VF-129 Board··············································2-5 2-5. Lens Block (TRV66E), (TRV77E) ··································2-6 2-6. Mechanism Deck, VC-214, DD-117 Boards···················2-8 2-7. V ideo Light (TRV66E) ··················································2-10 2-8. CF-56 Board ··································································2-10 2-9. How to Identify Drum and Note····································2-10 2-10. Circuit Boards Location ················································ 2-11 2-11. Flexible Boards Location ·············································· 2-12

3. BLOCK DIAGRAMS

3-1. Overall Block Diagram ···················································3-1 3-2. Camera/Video Block Diagram ········································3-5 3-3. VTR/Camera Control Block Diagram·····························3-9 3-4. Servo Block Diagram ····················································3-12 3-5. Mode Control Block Diagram ·······································3-15 3-6. Audio Block Diagram ···················································3-19 3-7. LCD Block Diagram ·····················································3-23 3-8. EVF Block Diagram ······················································3-27 3-9. Power Block Diagram ···················································3-29

4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

4-1. Frame Schematic Diagram-1···········································4-1

Frame Schematic Diagram-2··········································· 4-4

4-2. Printed Wiring Boards and Schematic Diagrams ············4-7

• CD-209 (CCD Imager) Printed Wiring Board and Schematic Diagram ·········································4-8

• VC-214 (Camera Processor, Y/C Processor, Focus/Zoom

Motor Drive, REC/PB Head AMP, Video/Interface, IR Transmitter, Mode Control, System Control, Servo, HI Control, Audio Processor)

Printed Wiring Board ····································4-11

• VC-214 (Camera Processor)(1/10)

Schematic Diagram .......................................4-17

• VC-214 (Y/C Processor)(2/10) Schematic Diagram ·······································4-19

• VC-214 (Focus/Zoom Motor Drive)(3/10) Schematic Diagram ·······································4-25

• VC-214 (REC/PB Head AMP)(4/10) Schematic Diagram ·······································4-27

• VC-214 (Video/Interface)(5/10) Schematic Diagram ·······································4-31

• VC-214 (IR Transmitter)(6/10) Schematic Diagram ·······································4-33

• VC-214 (Mode Control)(7/10) Schematic Diagram ·······································4-36

• VC-214 (Servo)(8/10) Schematic Diagram ·······································4-39

• FP-249 (S/T Reel Sensor), FP-356 (Top Sensor),

FP-355 (Tape LED) Flexible Board

Printed Wiring Boards···································4-42

• VL-23 (Video Light) (TRV66E only) Printed Wiring Board ····································4-43

• VC-214 (HI Control)(9/10) Schematic Diagram ·······································4-44

• VC-214 (Audio)(10/10) Schematic Diagram ·······································4-47

• SE-83 (Steady Shot), PJ-92 (AV IN/OUT) Printed Wiring Boards···································4-50

• SE-83 (Steady Shot), PJ-92 (AV IN/OUT) Schematic Diagrams ·····································4-53

• MA-351 (Stereo MIC AMP, Laser Link) Printed Wiring Board ····································4-55

• MA-351 (Stereo MIC AMP, Laser Link) Schematic Diagram ·······································4-57

— 3 —

Page 4

• PD-105 (RGB Decoder, LCD, Timing Generator, Back Light Drive)

Printed Wiring Board ····································4-60

• PD-105 (RGB Decoder, LCD)(1/2)

Schematic Diagram ·······································4-63

• PD-105 (Timing Generator, Back Light Drive)(2/2)

Schematic Diagram ·······································4-67

• VF-129 (B/W EVF)

Printed Wiring Board and

Schematic Diagram .......................................4-69

• CF-56 (User Control)

Printed Wiring Board ....................................4-72

• CF-56 (User Control)

Schematic Diagram ·······································4-75

• DD-117 (DC/DC Converter)

Printed Wiring Board ····································4-79

• DD-117 (DC/DC Converter)

Schematic Diagram ·······································4-81

• FK-8500, SS-8500 (Control Switch Block)

Schematic Diagram ·······································4-88

5. ADJUSTMENTS

5-1. CAMERA SECTION ADJUSTMENT ···························5-1 1-1. Preparations before Adjustment (Camera Section) ·········5-1 1-1-1.List of Service Tools························································5-1 1-1-2.Adjusting Items When Replacing Main Parts ·················5-2 1-1-3.Preparations ·····································································5-3 1-1-4.Precaution ········································································5-5

1. Setting the Switch····························································5-5

2. Order of Adjustments ······················································5-5

3. Subjects ···········································································5-5 1-2. Initialization of D, E, F Page Data ··································5-6

1. Initializing the D, E, F Page Data····································5-6

2. Modification of D, E, F Page Data ··································5-6

3. D Page Table····································································5-6

4. F Page Table ····································································5-7

5. E Page Table ··································································5-10 1-3. Camera System Adjustments ·········································5-13

1. HALL Adjustment ·························································5-13

2. Flange Back Adjustment ···············································5-13 2-1. Flange Back Adjustment (1) ··········································5-13 2-2. Flange Back Adjustment (2) ··········································5-14

3. Flange Back Check························································5-14

4. Picture Frame Setting ····················································5-15

5. AGC Gain Calibration Adjustment ·······························5-15

6. Color Reproduction Adjustment····································5-16

7. IRIS IN/OUT Adjustment ·············································5-16

8. MAX GAIN Adjustment ···············································5-17

9. Auto White Balance Standard Data Input ·····················5-17

10. Auto White Balance Adjustment ···································5-18

11. White Balance Check ····················································5-19

12. Angular Velocity Sensor Sensitivity Preset and Steady Shot Check·························································5-20

1-4. Monochrome Electronic Viewfinder System

Adjustment ···································································· 5-21

1-4-1.Horizontal Slant Check ·················································5-21 1-4-2.Centering Adjustment····················································5-21 1-4-3.Focus Adjustment ··························································5-21 1-4-4.Aberration Adjustment ··················································5-22 1-4-5.Horizontal Amplitude Adjustment (VF-129 board) ······ 5-22 1-4-6.Vertical Amplitude Adjustment (VF-129 board) ···········5-23 1-4-7.Brightness Adjustment (VF-129 Board)························ 5-23 1-4-8.Horizontal Amplitude, V ertical Amplitude,

Focus Check ··································································5-23

1-5. LCD System Adjustment ···············································5-24

1. LCD Initial Data Input ··················································5-24

2. VCO Adjustment (PD-105 board)·································5-25

3. D range Adjustment (PD-105 board)····························· 5-25

4. Bright Adjustment (PD-105 board) ·······························5-26

5. Contrast Adjustment (PD-105 board)····························5-26

6. V-COM Level Adjustment (PD-105 board) ··················5-27

7. Color Adjustment (PD-105 board) ································5-27

8. V-COM Adjustment (PD-105 board) ····························5-28

9. White Balance Adjustment (PD-105 board)··················5-28 5-2. MECHANISM SECTION ADJUSTMENT ··················5-29 2-1. Operating Without Cassette··········································· 5-29 2-2. Tape Path Adjustment····················································5-29 5-3. VIDEO SECTION ADJUSTMENT ······························5-30 3-1. Preparations Before Adjustments ··································5-30 3-1-1.Equipment to Required··················································5-30 3-1-2.Precautions on Adjusting···············································5-31 3-1-3.Adjusting Connectors ····················································5-31 3-1-4.Connecting the Equipments···········································5-32 3-1-5.Alignment Ta pe ·····························································5-33 3-1-6.Input/Output Level and Impedance ·······························5-33 3-1-7.Recording Mode (Standard 8/Hi8) Switching···············5-33 3-2. System Control System Adjustment ······························5-34

1. Initialization of D, E, F Page Data ································ 5-34

2. Battery End Adjustment (VC-214 board)······················5-34 3-3. Servo System Adjustments ············································5-35

1. CAP FG Offset Adjustment (VC-214 board) ················5-35

2. Switching Position Adjustment (VC-214 board)···········5-35 3-4. Video System Adjustments············································5-36

1. 28 MHz Origin Oscillation Adjustment (VC-214 board) ·····························································5-36

2. AFC f

Adjustment (VC-214 board)······························5-36

3. Filter f0 Adjustment (VC-214 board)·····························5-37

4. Y OUT Level Adjustment (VC-214 board) ···················5-37

5. C OUT Level Adjustment (VC-214 board) ···················5-38

6. RP Filter f

Adjustment (VC-214 board)·······················5-38

7. REC Y Current Adjustment (VC-214 board) ················5-39

8. REC L Level Adjustment (VC-214 board)····················5-40

9. REC C Current Adjustment (VC-214 board) ················5-41

3-5. IR Transmitter Adjustments···········································5-42

1. IR Video Carrier Frequency Adjustment (VC-214 board) ·····························································5-42

2. IR Video Deviation Adjustment (VC-214 board) ··········5-42

3. IR Audio Deviation Adjustment (VC-214 board) ·········5-43

3-6. Audio System Adjustment·············································5-44

1. 1.5 MHz Deviation Adjustment (VC-214 board) ··········5-45

2. 1.7 MHz Deviation Adjustment (VC-214 board) ··········5-45

3. BPF f0 Adjustment (VC-214 board) ·····························5-46

5-4. SERVICE MODE ··························································5-47 4-1. Adjustment Remote Commander ··································5-47

1. Using the Adjustment Remote Commander··················5-47

2. Precautions Upon Using the Adjustment Remote Commander ···································································5-47

4-2. Data Process ··································································5-48 4-3. Service Mode·································································5-49

1. Test Mode Setting ··························································5-49

2. Emergency Memory Address ········································ 5-50

2-1. EMG Code (Emergency Code) ·····································5-50 2-2. MSW Codes ··································································5-51

3. Bit Value Discrimination ···············································5-52

4. Input/Output Selection Check ·······································5-52

5. LED, LCD (Display Window) Check ···························5-52

6. Record of Use Check·····················································5-53

7. Switch Check (1) ···························································5-53

8. Switch Check (2) ···························································5-54

9. Headphone Jack Check ·················································5-54

6. REPAIR PARTS LIST

6-1. Exploded V iews ·······························································6-1 6-1-1.Front Panel (D) Block and Battery Panel (P) Block

Assembly ·········································································6-1

— 4 —

Page 5

6-1-2.Cabinet (R) Block Assembly···········································6-2 6-1-3.LCD Block Assembly······················································6-3 6-1-4.Cabinet (L) Block and Main Boards Assembly··············· 6-4 6-1-5.EVF Block Assembly ······················································6-5 6-1-6.Cassette Compartment Assembly····································6-6 6-1-7.LS Chassis Assembly ······················································6-7 6-1-8.Mechanism Chassis Assembly ········································6-8 6-2. Electrical Parts List ·························································6-9

* The color reproduction frame is shown on page 253.

— 5 —

Page 6

SERVICE NOTE

1. POWER SUPPLY DURING REPAIRS

In this unit, about 10 seconds after power is supplied (8.4V) to the battery terminal using the service power cord (J-6082-223-A), the power is shut off so that the unit cannot operate. This following two methods are av ailable to pre vent this. Take note of which to use during repairs.

Method 1.

Connect the servicing remote commander RM-95 (J-6082-053-B) to the LANC jack, and set the remote commander switch to the “ADJ” side.

Method 2.

Press the battery switch of the battery terminal using adhesive tape, etc.

Method 3.

Battery terminal

‘

Use the DC IN terminal. (Use the AC power adaptor.)

DC IN terminal

Battery SIG terminal

2. TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT)

1 Refer to 2-1. to remove the front panel assembly. 2 Refer to 2-1. to remove the cabinet (R) assembly. 3 Refer to 2-1. to remove the battery panel assembly. 4 Refer to 2-1. to remove the cabinet (L) assembly. 5 Disconnect CN901 of VC-214 board. 6 Add +5V from the DC POWER SUPPLY and unload with a

pressing the cassette lid.

Battery switch

Battery terminal

’

Let go your hold the cassette lid and rise the cassette compartment to take out a cassette.

Pull the timing belt in the direction of

arrow the cassette lid (take care not to damage) to adjust the bending of a tape.

with a pinsette while pressing

Pinsette

Timing belt

Press the cassette lid to rise the cassette compartment

[DC power supply]

(+5V)

Loading motor

Timing belt

Disconnect CN901 of VC-214 board.

Adjust the bending of a tape

— 6 —

Page 7

SELF-DIAGNOSIS FUNCTION

1. Self-diagnosis Function

When problems occur while the unit is operating, the self-diagnosis function starts working, and displays on the viewfinder or Display window what to do. This function consists of two display; selfdiagnosis display and service mode display. Details of the self-diagnosis functions are provided in the Instruction manual.

Viewfinder Display window

C : 3 1 : 1 1

Repaired by:

C : Corrected by customer H : Corrected by dealer E : Corrected by service

engineer

Blinks at 3.2Hz

Indicates the appropriate step to be taken. E.g.

31 ....Reload the tape.

32 ....Turn on power again.

3 1

Block

1 1

C : 3 1 : 11

Refer to page 8 and 9. Self-diagnosis Code Table.

2. Self-diagnosis Display

When problems occur while the unit is operating, the counter of the viewfinder or Display window shows a 4-digit display consisting of an alphabet and numbers, which blinks at 3.2 Hz. This 5-character display indicates the “repaired by:”, “block” in which the problem occurred, and “detailed code” of the problem.

Display window

Detailed Code

3. Service Mode Display

The service mode display shows up to six self-diagnosis codes shown in the past.

3-1. Display Method

While pressing the “STOP” key, set the switch from OFF to “VTR or PLAYER”, and continue pressing the “STOP” key for 5 seconds continuously. The service mode will be displayed, and the counter will show the backup No. and the 5-character self-diagnosis codes.

Viewfinder

[3] C : 3 1 : 1 1

Lights up

[3]

Backup No.

Order of previous errors

C : 3 1 : 1 1

Self-diagnosis Codes

3-2. Switching of Backup No.

By rotating the control dial, past self-diagnosis codes will be shown in order. The backup No. in the [] indicates the order in which the problem occurred. (If the number of problems which occurred is less than 6, only the number of problems which occurred will be shown.) [1] : Occurred first time [4] : Occurred fourth time [2] : Occurred second time [5] : Occurred fifth time [3] : Occurred third time [6] : Occurred the last time

Display window

3 C : 3 1 : 11

Control dial

3-3. End of Display

Turning OFF the power supply will end the service mode display.

Note: The “self-diagnosis display” data will be backed up by the coin-type lithium battery (CF-56 board BH001). When this

coin-type lithium battery is disconnected, the “self-diagnosis display” data will be lost by initialization.

— 7 —

Page 8

4. Self-diagnosis Code Table

Self-diagnosis Code

Block

Function

Repaired by:

Detailed

Code

00 00 00

11 20

21 22 23 30 31 40 41 42 43 44

Symptom/State

Condensation. Video head is dirty. Non-standard battery is used. LOAD direction. Loading does not

complete within specified time UNLOAD direction. Loading does not

complete within specified time T reel side tape slacking when unloading S reel

side tape slacking when unloading T reel fault. S reel fault. FG fault when starting capstan. FG fault during normal capstan operations. FG fault when starting drum. PG fault when starting drum. FG fault during normal drum operations. PG fault during normal drum operations. Phase fault during normal drum operations. LOAD direction loading motor time-

out. UNLOAD direction loading motor

time-out. T reel side tape slacking when

unloading. S reel side tape slacking when

unloading. T reel fault.

S reel fault.

FG fault when starting capstan. FG fault during normal capstan

operations. FG fault when starting drum.

PG fault when starting drum. FG fault during normal drum

operations. PG fault during normal drum

operations. Phase fault during normal drum

operations.

Correction

Remove the cassette, and insert it again after one hour. Clean with the optional cleaning cassette. Use the InfoLITHIUM battery.

Load the tape again, and perform operations from the beginning.

Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Remove the battery or power cable, connect, and perform

operations from the beginning. Remove the battery or power cable, connect, and perform

operations from the beginning.

— 8 —

Page 9

Self-diagnosis Code

Block

Function

Repaired by:

Detailed

Code

Symptom/State

Difficult to adjust focus (Cannot initialize focus.)

Zoom operations fault (Cannot initialize zoom lens.)

Handshake correction function does not work well. (With pitch angular velocity sensor output stopped.)

Handshake correction function does not work well. (With yaw angular velocity sensor output stopped.)

Correction

Inspect the lens block focus reset sensor (Pin !™ of CN551 of VC214 board) when focusing is performed when the control dial is rotated in the focus manual mode and the focus motor drive circuit (IC552 of VC-214 board) when the focusing is not performed.

Note: Use the remote commander RM-95 only for the model without the

focus dial.

Inspect the lens block zoom reset sensor (Pin !¢ of CN551 of VC214 board) when zooming is performed when the zoom lens is operated and the zoom motor drive circuit (IC552 of VC-214 board) when zooming is not performed.

Inspect pitch angular velocity sensor (SE451 of SE-83 board) peripheral circuits.

Inspect yaw angular velocity sensor (SE452 of SE-83 board) peripheral circuits.

— 9 —

Page 10

SECTION 1

GENERAL

CCD-TRV66E/TRV77E

This section is extracted from instruction manual. (CCD-TRV66E model)

1-1

Page 11

1-2

Page 12

1-3

Page 13

1-4

Page 14

1-5

Page 15

1-6

Page 16

1-7

Page 17

1-8

Page 18

1-9

Page 19

1-10

Page 20

1-11

Page 21

1-12

Page 22

1-13

Page 23

1-14

Page 24

1-15

Page 25

1-16

Page 26

1-17

Page 27

1-18

Page 28

1-19

Page 29

1-20

Page 30

1-21

Page 31

1-22

Page 32

1-23

Page 33

1-24E

Page 34

SECTION 2

DISASSEMBLY

The following flow chart shows the disassembly procedure.

2-1. LCD UNIT, PD-105 board

CCD-TRV66E/TRV77E

2-2. CABINET (R) ASSEMBLY (TRV66E)(TRV77E)

2-3 MECHANISM DECK (Note) Note : Use the parts only which can be removed

easily from outside of the MECHANISM DECK.

2-4. EVF BLOCK,

VF-129 board

How to remove the CRT UNIT

2-5. LENS BLOCK (TRV66E)(TRV77E)

2-6. MECHANISM DECK,

VC-214 board, DD-117 board

2-7. VIDEO LIGHT (TRV66E)

2-8. CF-56 board

MECHANISM DECK check service position

EVF check service position

LENS BLOCK check service position

MECHANISM DECK, VC-214 board, DD-117 board check service position

2-9. How to identify drum and note

2-1

Page 35

NOTE: F ollo w the disassembly procedure in the numerical order given.

2-1. LCD UNIT, PD-105 BOARD

Rotate it by 90 ° in the

direction of the arrow.

Press the button.

Open the LCD panel.

Two screws (M2 × 4)

!¡

Claws

!¶

PD-105 board

!£

Claws

!∞

Back light Cold cathode fluorescent tube

Claws

Indication LCD block assembly

PD-105

P cabinet (C)(93)

Hinge assembly

Two tapping screw

(B2 × 8)

!™

Screw

(M2

!¢

Panel frame (93)

assembly

!§

LCD UNIT

Claws

P cabinet (M)(93)

assembly

[LCD CHECK SERVICE POSITION]

Indication LCD block assembly

PD-105 board

PD-105

Two tapping screws

(B2

Adjustment remote commander (RM-95)

AC POWER ADAPTOR

LANC jack

AC IN

Multi CPC jig (J-6082-311-A)

CN5501

LCD Back light Cold cathode fluorescent tube

2-2

Base (Use box or the like.)

Page 36

2-2. CABINET (R) ASSEMBLY (TRV66E)

FP-43 flexible

board (20P)

Screw

(M2

4),

Screw

(M2

4),

lock ace, p2

T wo screws

(M2

4),

lock ace, p2

Cabinet (L)

lock ace, p2

Remove

the claw

Panel (D) (front)

assembly

Remove the claws Remove it while taking care as the FP-43 flexible cable is connected.

CABINET (R) ASSEMBLY (TRV77E)

VC-214 Board

!™

Screw (M2 lock ace, p2

Screw

(M2

4),

lock ace, p2

4),

!∞

assembly

!¢

Remove the

claws

!£

Two screws (M2 × 4),

lock ace, p2

!¡

Screw (M2 × 4),

lock ace, p2

Cabinet (R)

Three screws

(M2

4),

lock ace, p2



1 Two screws (M2

4),

lock ace, p2

Cabinet (L)

FP-43 flexible

board (20P)

Screw

(M2

4),

lock ace, p2

Remove

the claw

Panel (D) (front)

assembly

VC-214 Board

Screw

(M2

4),

lock ace, p2

Remove the claws Remove it while taking care as the FP-43 flexible cable is connected.

!™

Screw (M2 lock ace, p2

Screw

(M2

4),

lock ace, p2

4),

!∞

assembly

!¢

Remove the

claws

!£

Two screws (M2 × 4),

lock ace, p2

!¡

Screw (M2 × 4),

lock ace, p2

Cabinet (R)

Three screws

(M2

4),

lock ace, p2

2-3

Page 37

2-3. MECHANISM DECK

Two screws (M2

Screw (M2 × 4),

lock ace, p2

Jack cover

Cabinet (L)

assembly

Screw(M2 × 4),

lock ace, p2

Remove it in the direction

4),

Cassette lid

of the arrow

assembly

Battery panel (P)

assembly

Remove it in the direction

of the arrow

. Remove it gently as a thin flexible board is held

by a claw.

Disengage the claw

that fixes the flexible board.

VC-214

Screw

(M2

!™

MD frame (B)

!¡

T wo screws

(M2

[MECHANISM DECK CHECK SERVICE POSITION]

• How to move up the cassette

compartment manually

Press the cassette compartment in the direction of the arrow

to move it up in the direction of the arrow

FP-43 flexible board

Panel (D) (front) assembly



DC IN

AC POWER ADAPTOR

AC IN

Cabinet (L) assembly

Battery panel (P) assembly

Base (Use box or the like.)

LANC jack

Adjustment remote commander (RM-95)

Cabinet (R) assembly

(TRV66E)

(TRV77E)

2-4

Page 38

2-4. EVF BLOCK, VF-129 BOARD

Screw

Tilt lock (93)

Slide the button in the

direction of the arrow a.

AC POWER ADAPTOR

Cabinet (R) assembly

AC IN

LANC jack

DC IN

Adjustment remote commander (RM-95)

CPC-7 jig (J-6082-382-A)

CPC-7 jig

@§

CRT socket (4P)

@ª

CRT

@•

Anode cable (1P) Do not pull the cable, but remove it in the vertical direction.

@¶

Remove the connector cover

with a flat head (–) screwdriver.

@∞

CRT DT connector (4P)

[How to remove the CRT unit]

FFC-236 flexible

flat cable (50P)

DP-74 harness

(10P)

Finder (S) assembly

Three tapping

screws (B2

!¶

T wo tapping

screws (B2 × 5)

@¡

T apping

screw (B2 × 5)

@™

EVF tally

@º

Cabinet (upper B) (93)

assembly

!ª

Cabinet (lower B) (93)

assembly

!§

Tapping screw (B2 × 5)

FFC-256

flexible flat cable (4P)

!£

FFC-256

flexible flat cable (4P)

!•

FFC-256

flexible flat cable (4P)

!¢

VF base(B)(93)

!∞

EVF block assembly

Rotate it in the direction of

the arrow

and remove it

in the direction of the arrow c.

!™

Remove

the claw

!¡

T wo screws

(M2 × 3)

Harness guide

@¢

CRT assembly

@£

VF-129 board

[EVF CHECK SERVICE POSITION]

Contacting surface

Panel (D) (front) assembly

FP-43 flexible board

(TRV66E)

(TRV77E)

2-5

Page 39

2-5. LENS BLOCK (TRV66E)

Screw (M2 × 3)

LENS block

VL-23 board

Screw

(M2 × 3)

!™

MD frame (B)

!¡

T wo screws

(M2 × 3)

Flexible board

(from LENS block) (24P)

Screw (M2 × 3)

VC-214 Board

IM shield

assembly

FP-54 flexible board

LENS BLOCK (TRV77E)

Intelligent

accessory shoe

Four screws

(M2 × 3)

Screw (M2 × 3)

Flexible board

(from LENS block) (24P)

LENS block

Screw (M2 × 3)

VC-214 Board

FP-54 flexible board

!™

MD frame (B)

!¡

T wo screws

(M2 × 3)

Screw (M2 × 3)

2-6

IM shield

assembly

Page 40

[LENS BLOCK CHECK SERVICE POSITION]

Adjustment remote commander (RM-95)

Extension cable (J-6082-357-A) (16P)

LENS BLOCK

Base (Fix the lens block using a vise or the like.)

LANC jack

VC-214

Board

FP-43 flexible board

Base (Use box or the like) (Supports the VL-23 board)

CPC-7 jig (J-6082-382-A)

Cabinet (R) assembly

AC POWER ADAPTOR

DC IN

CPC-7 jig

Contacting surface

AC IN

2-7

Page 41

2-6. MECHANISM DECK, VC-214, DD-117 BOARDS

Remove it in the direction of the arrow b.

T wo screws

(M2

4),

lock ace, p2

!ª

Slide it in the direction of the arrow disengage the claw

and

Remove the control switch block(FK-8500) in the direction of the arrow

@£

Remove the claws

@º

T wo screws

(M2

4),

lock ace, p2

Cassette Lid assembly

Remove

!•

the claw

!™

Cabinet (L) assembly

Jack cover

Screw

(M2

lock ace, p2

4),

lock ace, p2

@¢

VC-214

board

VC-214 Board

Screw (M2 × 4),

!¢

(SS-8500)

!º

Screw

!¶

DD-117

board

Remove it in the direction of the arrow a. Remove it gently as a thin flexible board is held by a claw.

Control switch block

!£

T wo tapping

screws (B2

DD-117

@™

Screw

(M2

FFC-236 flexible flat cable (50P)

Disengage the claw

that fixes the flexible board.

Battery panel (P)

assembly

!∞

T wo screws

(M2

!§

Board to board connector (70P)

@¡

PJ-92 board

@∞

Mechanism

deck

!¡

Screw

(M2

DP-74 harness

(10P)

Cabinet (R) assembly

2-8

Page 42

[MECHANISM DECK, VC-214, DD-117 BOARDS CHECK SERVICE POSITION]

(TRV66E)

Panel (D) (front) assembly

(TRV77E)

FP-43 flexible board

LENS block

Mechanism deck

Base 3

PJ-92 board

DC IN

DD-117 board

Extension cable (J-6082-439-A) (70P)

VL-23 board (TRV66E only)

AC IN

Battery panel (P)

AC POWER ADAPTOR

assembly

Base 2

Control switch block (SS-8500)

FP-46 flexible board (TRV66E only)

Adjustment remote commander (RM-95)

Control switch block (FK-8500)

Base 1

VC-214 board FFC-236 flexible flat cable (50P)

DP-74 harness (10P)

Cabinet (R) assembly

Base 1-3 (Use box or the like)

CPC-7 jig (J-6082-382-A)

(TRV66E)

Base Fix the lens block using a vise or the like.

CD-209 board

Flexible board (from LENS block) (24P)

Extension Cable (J-6082-357-A) (16P)

Contacting surface

2-9

Page 43

2-7. VIDEO LIGHT (TRV66E)

in the direction of the arrow a.

2-8. CF-56 BOARD

flexible flat cable (4P)

Remove the lamp holder

Note : When attaching it. Align the switch position as shown.

FFC-256

Halogen lamp

Remove the claws

Speaker harness (2P)

CF-56

Five tapping

screws (B2 × 5)

CF-56 board

2-9. HOW TO IDENTIFY DRUM AND NOTE

TYPE A

(Direct bearing type)

Circular rib

(When a drum is viewed from the top.)

Note

Ref.No. TYPE

The fixing screw differs depending on the types of drums. Be sure to check the type of drum and use the screw of the same type. Be careful that the drum of DGH-0F1A-R (Type A) only is supplied as repair part.

M901

DGH-0F1A-R

DGH-0E9A-R

Speaker

Spacer (SP)

Flexible board (4P)

DP-74 harness (11P)

DP-74 harness (6P)

Control switch block

(MR-8500) (8P)

TYPE B

(Shaft press fit type)

Radial rib

808

SCREW ASSY, DRUM ATTACHED

∫

X-3947-895-1 SCREW (M1.4)

∫

3-971-939-01

M901 A-7048-899-A DRUM BLOCK ASSY

(DGH-0F1A-R)

808 X-3947-895-1 SCREW ASSY, DRUM ATTACHED

(TYPE A)

808 3-971-939-01 SCREW (M1.4) (TYPE B)

2-10

Page 44

2-10.CIRCUIT BOARDS LOCATION

(TRV77E)(TRV66E)

VF-129 (B/W EVF)

DD-117 (DC/DC CONVERTER)

SE-83 (STEADY SHOT)

CD-209 (CCD IMAGER)

VL-23 (VIDEO LIGHT)

MA-351 STEREO MIC AMP,

PJ-92 (AV IN/OUT)

LASER LINK

VF-129 (B/W EVF)

DD-117 (DC/DC CONVERTER)

SE-83 (STEADY SHOT)

CD-209 (CCD IMAGER)

MA-351

STEREO MIC AMP,

LASER LINK

PJ-92 (AV IN/OUT)

(TRV66E/TRV77E)

CF-56 (USER CONTROL)

PD-105 RGB DECODER, LCD, TIMING GENERATOR, BACK LIGHT DRIVE

VC-214 CAMERA PROCESSOR, Y/C PROCESSOR, FOCUS/ZOOM MOTOR DRIVE, REC/PB HEAD AMP, VIDEO/INTERFA CE, IR TRANSMITTER, MODE CONTROL, SERVO, HI CONTROL, SYSTEM CONTROL, AUDIO PROCESSOR

2-11

Page 45

2-11.FLEXIBLE BOARDS LOCATION

(TRV77E)(TRV66E)

CONTROL SWITCH BLOCK (FK-8500)

FP-44

From LOADING MOTOR, MODE SWITCH

(TRV66E/TRV77E)

CONTROL SWITCH BLOCK (SS-8500)

FFC-256

FP-46 From S/T REEL

SENSOR From CAPSTAN MOTOR From DRUM MOTOR

From VIDEO HEAD

FP-642

FP-62

CONTROL SWITCH BLOCK (FK-8500)

FP-44

From LOADING MOTOR, MODE SWITCH

FP-49

FP-54

FP-45 From S/T REEL

SENSOR From CAPSTAN

MOTOR From DRUM MOTOR

From VIDEO HEAD

FFC-236

CONTROL SWITCH BLOCK (MR-8500)

2-12E

FP-43

(From LENS BLOCK)

Page 46

3-1. OVERALL BLOCK DIAGRAM

SECTION 3

CCD-TRV66E/TRV77E

BLOCK DIAGRAMS

3-1 3-2 3-3 3-4

Page 47

CCD-TRV66E/TRV77E

3-2. CAMERA/VIDEO BLOCK DIAGRAM

IC1401 7 

IC1401 !£,!¢

IC1401 !™



14.187 MHz

1.1Vp-p

3.7Vp-p

3.3Vp-p

IC1402 6



IC1401 3,4 

IC1401 1,2

IC502 @§



CAMERA REC



1.2Vp-p

IC502 #¢ IC501 @§ CAMERA REC

7.0Vp-p

IC501 !¡ CAMERA REC/PB

3.0Vp-p

14.187 MHz

6.8Vp-p

IC501 5 CAMERA REC/PB

28.374 MHz

3.0Vp-p

LINE REC

1.2Vp-p

0.5Vp-p

IC502 2 – 9 CAMERA REC/PB LINE REC

72 nsec

2.9Vp-p

IC502 #§ PB

0.3Vp-p

IC202 6 CAMERA REC/PB

0.8Vp-p

IC202 6 LINE REC

0.9Vp-p

IC502 !§ CAMERA REC/PB



LINE REC

14.187 MHz

2.9Vp-p

IC202 !§ CAMERA REC

0.2 µsec



IC202 $º PB

0.4Vp-p

0.1 µsec/div

IC202 !£ CAMERA REC

0.4Vp-p

IC001 $¶ CAMERA REC

1 µsec/div, 0.1 V/div



IC001 1 CAMERA REC

IC001 !¢ PB

1 µsec/div, 0.2 V/div

0.1 µsec/div

0.3Vp-p

IC001 @¶,#¢ CAMERA REC

0.2 µsec/div, 1 V/div

CN001 !§, Q001 C CAMERA REC

7.14 MHz

9.0Vp-p

IC501 @• CAMERA REC

IC501 @¡ CAMERA REC

50 nsec

7.0Vp-p

3.0Vp-p

IC151 @ª CAMERA REC/PB

IC151 ^º LINE REC

IC151 ^¢ LINE REC

2Vp-p

0.3Vp-p

IC151 @∞ CAMERA REC/PB

IC151 !¶ CAMERA REC/PB

0.4Vp-p

0.12Vp-p

IC151 ^™ LINE REC

0.06Vp-p

IC202 $¶ LINE REC/PB

3.0Vp-p

13.325 MHz

IC202 @§ CAMERA REC/PB

0.1Vp-p

IC202 @§

0.48Vp-p

IC151 $§ LINE REC

0.52Vp-p

IC151 $¢ LINE REC

0.16Vp-p

IC151 @¶ CAMERA REC/PB IR ON

0.5Vp-p

LINE REC

0.3Vp-p

IC202 3 CAMERA REC/PB

IC202 @£ CAMERA REC/PB

IC202 @£ LINE REC

0.45Vp-p

IC202 3 LINE REC

0.3Vp-p

0.5Vp-p

IC202 #£ CAMERA REC/PB

IC202 #£ LINE REC

1.0Vp-p

IC202 &™ CAMERA REC/PB

25 Hz



2.8Vp-p

0.9Vp-p

IC151 #¶ LINE REC

17.7343 MHz

0.26Vp-p

3-5 3-6 3-7 3-8

Page 48

3-3. VTR/CAMERA CONTROL BLOCK DIAGRAM

IC402 1

20.0 MHz

CCD-TRV66E/TRV77E

1.7Vp-p

IC402 $¶



25 Hz

2.8Vp-p

3-9 3-10 3-11

Page 49

CCD-TRV66E/TRV77E

3-4. SERVO BLOCK DIAGRAM

IC801 !¡ 

25 Hz

IC801 !•



2.8Vp-p

150 Hz

2.8Vp-p

IC402 1

20.0 MHz

1.7Vp-p

IC802 9

IC802 7



10.3 µsec

1.0 msec/div

0.1Vp-p

100mV

IC801 ^¢



2 µsec

IC801 4



2 µsec

0.75Vp-p

IC801 1,2,@ª

150 Hz

1.2Vp-p

IC402 $¶



2.8Vp-p

25 Hz

3-12 3-13 3-14

Page 50

3-5. MODE CONTROL BLOCK DIAGRAM

IC604 %£ 

IC604 $º

20.0 MHz

3.2Vp-p

CCD-TRV66E/TRV77E

32.768 KHz

3.2Vp-p

3-15 3-16 3-17

Page 51

CCD-TRV66E/TRV77E

3-6. AUDIO BLOCK DIAGRAM

IC751 $¡ CAMERA REC/PB IR ON

0.22Vp-p

IC751 7 CAMERA REC/PB

4.43 MHz

0.2Vp-p

IC751 @™ CAMERA REC/PB IR ON

0.5 µsec/div

0.22Vp-p

3-19 3-20 3-21 3-22

Page 52

3-7. LCD BLOCK DIAGRAM

IC5502 @¢ 

CCD-TRV66E/TRV77E

IC5502 @™

2.0Vp-p

IC5502 @º



2.0Vp-p

IC5502 8

IC5502 9



0.4Vp-p

0.3Vp-p

IC5502 !º



IC5602 7 

0.1Vp-p

6.7 KHz

5.0Vp-p

IC5601 @§

3.0Vp-p

5.48 MHz

IC5601 #¶



2.8Vp-p

3-23 3-24 3-25

Page 53

CCD-TRV66E/TRV77E

3-8. EVF BLOCK DIAGRAM

IC901 7 

IC901 !¡ 

IC901 !§ 

0.9Vp-p

2.4Vp-p

IC901 !£

1.1Vp-p

IC901 3



20 msec

2.0Vp-p

IC901 1,5

20 msec

2.0Vp-p

20 msec

1.1Vp-p

3-27 3-28

Page 54

3-9. POWER BLOCK DIAGRAM

CCD-TRV66E/TRV77E

3-29 3-30 3-31 3-32E

Page 55

PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

4-1. FRAME SCHEMATIC DIAGRAM-1

SECTION 4

CCD-TRV66E/TRV77E

4-1 4-2 4-3

FRAME SCHEMATIC DIAGRAM (1/2)

Page 56

CCD-TRV66E/TRV77E

FRAME SCHEMATIC DIAGRAM-2

FRAME SCHEMATIC DIAGRAM (2/2)

4-4 4-5 4-6

Page 57

CCD-TRV66E/TRV77E

Front of the lens

1.5 m

Pattern box

4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

THIS NOTE IS COMMON FOR WIRING BOARDS AND SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block)

(For printed wiring boards)

• b: Pattern from the side which enables seeing. (The other layers' patterns are not indicated.)

• Through hole is omitted.

• Circled numbers refer to waveforms.

• There are few cases that the part printed on diagram

isn’t mounted in this model.

• Chip parts.

Transistor Diode

21321321

(For schematic diagrams)

• All capacitors are in µF unless otherwise noted. pF : µµF.

50V or less are not indicated except for electrolytics and tantalums.

• Chip resistors are 1/10W unless otherwise noted.

kΩ=1000Ω, MΩ=1000kΩ.

• Caution when replacing chip parts.

New parts must be attached after removal of chip. Be careful not to heat the minus side of tantalum capacitor, Because it is damaged by the heat.

• Some chip part will be indicated as follows.

Example C541 L452

22U 10UH TA A 2520

(Measuring conditions voltage and waveform)

• Voltages and waveforms are measured between the measurement points and ground when camera shoots color bar chart of pattern box. They are reference values and reference waveforms. (VOM of DC 10 MΩ input impedance is used.).

• Voltage values change depending upon input impedance of VOM used.)

1. Connection

CD-209 BOARD

C1401 A-2 C1405 A-1 C1406 A-1 C1407 B-2 C1408 B-2 C1409 B-1 C1410 B-1 C1411 B-2 C1412 B-1

CN1401 A-3 IC1401 A-3

IC1402 B-2 L1401 A-2

L1402 B-1 R1401 A-1

R1405 A-1 R1406 B-2 R1407 B-2 R1408 B-2 R1409 B-1

CD-209 (CCD IMAGER) PRINTED WIRING BOARD

— Ref. No. CD-209 Board; 10,000 Series —

Kinds of capacitor

Temperature characteristics

External dimensions (mm)

• Constants of resistors, capacitors, ICs and etc with XX indicate that they are not used. In such cases, the unused circuits may be indicated.

• Parts with ★ differ according to the model/destination. Refer to the mount table for each function.

• All variable and adjustable resistors have characteristic curve B, unless otherwise noted.

• Signal name XEDIT→ EDIT PB/XREC → PB/REC

• 2 : non flammable resistor

• 1 : fusible resistor

• C : panel designation

• A : B+ Line

• B : B– Line

• J : IN/OUT direction of (+,–) B LINE.

• C : adjustment for repair.

• Circled numbers refer to waveforms.

Note : The components identified by mark ! or dotted

line with mark ! are critical for safety. Replace only with part number specified.

2. Adjust the distance so that the output waveform of Fig. a and the Fig. b can be obtain.

Yellow

Cyan

White

Magenta

Green

Red

Blue

AABBA=B

Fig. a (Video output terminal output waveform)

Electron beam scanned frame

Red

Cyan

White

Green

Yellow

Blue

Magenta

CRT picture frame

Fig.b (Picture on monitor TV)

When indicating parts by reference number, pleas include the board name.

For printed wiring boards

• This board is six-layer print board. However, the patterns of layers two to five have not been included in the diagram.

There are few cases that the part printed on this diagram isn’t mounted in this model.

(TRV77E)(TRV66E)

VF-129 (B/W EVF)

CD-209 (CCD IMAGER)

VF-129 (B/W EVF)

CD-209 (CCD IMAGER)

VL-23 (VIDEO LIGHT)

CD-209

BOARD

CAMERA REC

1 IC1401 1,2

2 IC1401 3,4



3 IC1401 7



4 IC1401 !™



5 IC1401 !£,!¢

6 IC1402 6



6.8Vp-p

1.1Vp-p

14.187 MHz

3.3Vp-p

14.187 MHz

DD-117 (DC/DC CONVERTER)

SE-83 (STEADY SHOT)

MA-351 STEREO MIC AMP, LASER LINK

PJ-92 (AV IN/OUT)

DD-117 (DC/DC CONVERTER)

SE-83 (STEADY SHOT)

PJ-92 (AV IN/OUT)

MA-351 STEREO MIC AMP, LASER LINK

6.8Vp-p

4-7 4-8 4-9

3.7Vp-p

1.2Vp-p

CCD IMAGER

CD-209

Page 58

CCD-TRV66E/TRV77E

For printed wiring boards

• This board is six-layer print board. However, the patterns of layers two to five have not been included in the diagram.

• Chip parts Transistor

There are few cases that the part printed on this diagram isn’t mounted in this model.

(TRV66E/TRV77E)

CF-56 (USER CONTROL)

PD-105 RGB DECODER, LCD, TIMING GENERATOR, BACK LIGHT DRIVE

VC-214 CAMERA PROCESSOR, Y/C PROCESSOR, FOCUS/ZOOM MOTOR DRIVE, REC/PB HEAD AMP , VIDEO/INTERFACE, IR TRANSMITTER, MODE CONTROL, SERVO, HI CONTROL, SYSTEM CONTROL, AUDIO PROCESSOR

VC-214 BOARD (SIDE A)

C006 A-4 C008 A-5 C009 B-5 C011 B-5 C021 B-5 C022 B-5 C027 B-4 C028 B-4 C030 B-5 C031 B-4 C034 B-5 C035 C-4 C036 B-4 C038 B-3 C039 B-4 C040 B-4 C041 B-4 C045 B-5 C046 C-4 C047 B-5 C048 B-4 C052 B-5 C053 B-5 C056 B-4 C058 B-4 C062 C-5 C065 C-6 C069 C-6 C071 C-5 C073 B-3 C075 C-4 C078 C-4 C079 C-4 C081 C-5 C082 C-5 C084 C-5 C085 C-6 C088 C-5 C089 C-4 C156 C-2 C157 C-2 C158 C-2 C160 C-2 C161 C-2 C166 C-2 C171 C-1 C185 C-2 C187 C-2 C188 B-1 C189 B-1 C201 F-7 C204 E-8 C206 E-7 C209 D-5 C210 D-6 C217 E-7 C219 E-8 C224 E-7 C225 E-7 C226 E-7 C229 F-5 C230 E-6 C237 E-7 C239 F-7 C241 E-8 C245 E-7 C248 E-7 C250 E-7 C253 G-6 C306 A-1 C307 A-1 C308 B-1 C309 B-1 C310 B-1 C312 A-1 C313 A-1 C314 A-1 C315 B-1 C316 B-1 C317 A-1 C318 A-1 C319 A-1 C320 A-1 C321 A-1 C322 B-1 C323 A-1

C324 A-1 C325 B-1 C326 B-2 C327 A-1 C328 B-2 C329 A-2 C330 B-2 C331 B-2 C332 A-2 C333 A-2 C334 B-2 C335 A-2 C336 B-2 C337 A-3 C338 B-3 C339 A-3 C340 B-3 C341 A-3 C342 B-3 C343 B-1 C344 B-3 C345 A-3 C346 A-3 C347 B-3 C389 A-3 C402 A-7 C411 B-9 C412 B-8 C415 B-8 C416 B-8 C417 C-7 C418 A-7 C419 B-8 C502 E-5 C512 D-4 C513 D-5 C516 E-4 C517 D-4 C519 D-4 C520 D-4 C521 D-4 C522 D-4 C523 D-4 C524 D-4 C525 D-4 C526 D-4 C527 D-4 C528 D-5 C529 D-5 C530 D-5 C532 D-4 C533 D-4 C534 E-5 C535 D-4 C551 G-4 C552 F-4 C553 G-4 C555 E-4 C557 F-4 C558 F-4 C560 F-4 C561 F-5 C562 F-5 C565 E-4 C567 F-5 C568 F-5 C569 F-5 C570 F-5 C571 F-5 C572 G-4 C605 G-8 C612 E-8 C615 E-8 C616 E-8 C617 E-9 C618 E-9 C619 E-9 C620 E-9 C621 E-8 C622 E-8 C623 E-8 C624 E-8 C628 G-7 C629 G-7 C635 E-8 C636 E-8

C801 A-7 C802 A-7 C803 A-6 C804 B-6 C805 B-6 C806 B-7 C807 B-6 C808 B-7 C809 B-7 C810 B-7 C811 B-6 C812 B-7 C813 B-6 C814 C-6 C815 B-7 C816 B-6 C817 C-6 C818 B-6 C819 B-6 C820 B-7 C821 B-6 C822 B-7 C823 A-8 C836 A-9 C838 A-8 C839 A-9 C840 A-9

CN001 A-4 CN501 E-5 CN551 G-5 CN901 A-2 CN902 D-7 CN903 A-1 CN905 A-6 CN906 A-7 CN907 D-9 CN908 A-8 CN911 C-7 CN914 C-9

D002 C-4 D551 G-4 D610 D-6 D910 D-3 D911 E-3

FB002 A-4 FB004 A-5 FB201 E-8 FB203 F-5 FB206 E-7 FB506 E-5 FB602 E-8

IC001 B-4 IC202 F-6 IC301 B-2 IC402 B-8 IC502 D-5 IC551 F-4 IC604 F-8 IC801 B-6

L001 A-3 L002 B-5 L003 B-5 L004 B-3 L006 C-5 L009 B-3 L012 C-3 L013 C-5 L016 C-5 L018 C-5 L204 D-7 L205 D-6 L207 E-7 L502 D-4 L555 F-5

Q003 A-5 Q024 B-4 Q027 C-4 Q028 C-4 Q029 C-4 Q031 D-4

Q033 C-4 Q034 C-4 Q036 C-5 Q040 C-6 Q043 C-4 Q044 C-4 Q204 D-6 Q205 E-8 Q208 D-6 Q213 D-6 Q214 D-6 Q215 E-7 Q216 E-7 Q217 E-8 Q310 A-2 Q501 D-4 Q551 G-5 Q552 F-4 Q553 E-5 Q554 G-5 Q608 G-9 Q609 G-8 Q610 G-8 Q611 G-8 Q801 C-6 Q802 B-6 Q803 C-7 Q806 A-9

R004 A-5 R014 B-5 R035 B-5 R038 B-4 R039 B-4 R043 C-4 R044 B-4 R045 B-4 R046 C-4 R056 B-4 R058 B-4 R063 C-5 R071 D-4 R072 B-4 R073 B-4 R074 B-4 R075 C-3 R081 C-4 R082 C-4 R085 C-4 R086 D-4 R092 C-4 R093 C-5 R096 C-4 R098 C-4 R099 C-4 R101 C-4 R102 C-5 R103 C-5 R107 C-5 R113 C-5 R165 C-3 R166 C-2 R167 C-3 R170 C-3 R175 C-1 R183 C-2 R184 C-2 R201 E-6 R203 E-8 R206 E-8 R207 E-6 R209 E-6 R212 D-6 R213 E-6 R214 D-6 R215 D-6 R216 E-6 R217 F-7 R218 D-6 R219 D-7 R220 D-6 R221 D-6 R222 E-7 R225 D-6 R227 E-6 R228 D-6

R229 E-6 R230 E-6 R231 E-7 R232 E-6 R233 E-6 R234 E-6 R235 E-6 R236 E-6 R237 E-6 R238 E-6 R239 E-7 R241 E-6 R242 E-7 R243 E-8 R251 F-7 R252 F-7 R253 G-7 R255 E-8 R258 E-6 R259 E-7 R260 D-6 R261 E-7 R262 E-7 R308 B-1 R310 B-1 R313 A-1 R317 A-1 R318 B-2 R319 A-3 R320 B-2 R321 A-1 R322 A-3 R323 B-3 R325 B-3 R331 A-3 R343 A-3 R350 A-3 R405 A-7 R406 A-7 R407 A-8 R409 A-8 R410 A-8 R416 A-8 R420 B-8 R421 B-8 R432 B-9 R433 B-9 R434 B-8 R435 B-9 R436 B-8 R437 A-8 R440 B-9 R441 C-8 R513 D-4 R514 D-4 R515 D-4 R522 D-4 R523 D-5 R524 D-5 R525 D-5 R532 E-4 R551 G-4 R554 G-4 R555 G-5 R556 F-4 R557 G-4 R558 F-4 R559 F-4 R560 F-4 R561 E-4 R562 F-4 R563 F-4 R564 F-4 R565 F-4 R566 F-4 R567 F-5 R568 E-4 R569 F-4 R570 F-5 R571 E-4 R572 E-4 R573 E-4 R574 F-5 R574 F-5 R575 E-4 R576 F-5

R577 E-4 R579 F-4 R583 G-5 R605 G-9 R606 G-7 R610 G-8 R611 G-8 R613 G-9 R614 G-7 R622 F-9 R628 F-9 R645 E-8 R650 G-7 R664 E-8 R666 E-9 R667 E-9 R668 E-9 R669 E-9 R670 E-8 R671 E-8 R672 E-8 R673 E-8 R681 F-9 R682 F-9 R683 G-9 R684 G-9 R685 G-9 R690 E-8 R691 E-8 R693 G-9 R695 G-9 R696 G-9 R697 G-8 R698 E-8 R801 B-6 R802 B-6 R803 B-6 R804 A-6 R805 A-6 R806 B-6 R807 A-6 R808 B-6 R809 B-6 R813 A-8 R814 A-7 R815 A-7 R823 A-8 R825 A-8 R836 A-9 R837 A-9 R917 C-8 R918 C-8 R919 C-8 R920 C-8 R932 D-8 R933 D-8

VC-214 (CAMERA PROCESSOR, Y/C PROCESSOR, FOCUS/ZOOM MOTOR DRIVE, REC/PB HEAD AMP, VIDEO/INTERFACE,

IR TRANSMITTER, MODE CONTROL, SERVO, HI CONTROL, SYSTEM CONTROL, AUDIO PROCESSOR) PRINTED WIRING BOARD

— Ref. No. VC-214 Board; 1,000 Series —

CAMERA PROCESS, REC/PB HEAD AMP, VIDEO PROCESS, AUDIO, SERVO, SYSTEM CONTROL, MODE CONTROL

VC-214

4-11 4-12

Page 59

CCD-TRV66E/TRV77E

VC-214 BOARD (SIDE B)

C001 A-15 C004 A-14 C005 B-14 C007 A-14 C012 B-14 C024 B-15 C029 C-14 C032 B-14 C037 B-14 C042 B-14 C049 B-14 C050 B-15 C051 B-15 C054 B-15 C055 C-13 C057 B-14 C059 C-14 C060 B-15 C061 C-14 C066 A-15 C067 A-15 C068 B-15 C070 B-15 C072 B-16 C074 B-16 C076 B-16 C080 C-15 C083 B-15 C086 C-13 C087 C-14 C090 A-15 C152 C-16 C159 E-15 C162 C-16 C163 C-16 C164 C-16 C168 C-16 C169 C-18 C170 C-16 C172 C-18 C173 C-18 C174 C-18 C175 C-18 C176 C-18 C177 C-18 C178 B-18 C179 C-18 C180 C-17 C181 C-17 C182 B-17 C183 B-17 C184 C-17 C186 C-16 C190 C-16 C191 D-15 C192 D-15 C202 E-11 C203 E-11 C205 G-14 C207 E-12 C208 E-12 C211 E-11 C212 E-11 C213 E-13 C218 E-12 C227 E-13 C232 E-11 C233 F-13 C234 E-13 C235 E-11 C236 E-11 C243 G-12 C244 F-12 C246 E-13 C247 E-13 C249 G-12 C252 G-12 C301 B-18 C302 A-18 C371 C-15 C372 C-15 C378 D-15 C380 D-14 C381 C-14 C382 C-15 C383 C-15

C384 C-14 C385 C-15 C386 C-15 C387 C-15 C388 C-15 C390 D-15 C404 C-12 C405 B-12 C406 B-12 C410 C-11 C414 C-11 C420 B-11 C421 B-11 C501 E-15 C503 E-14 C506 F-14 C507 E-14 C509 F-14 C510 E-15 C514 D-14 C515 D-14 C518 D-14 C531 D-13 C536 F-14 C554 F-14 C556 F-14 C559 F-14 C563 F-15 C564 F-15 C566 F-15 C607 F-11 C610 F-10 C611 F-11 C613 F-10 C625 E-11 C626 E-11 C630 F-11 C634 E-11 C637 F-11 C702 A-13 C703 B-14 C704 B-13 C705 B-13 C706 B-13 C707 B-13 C708 A-13 C709 A-13 C710 A-13 C711 B-13 C712 B-13 C713 B-13 C714 A-13 C715 A-13 C716 B-12 C717 A-12 C751 B-16 C751 B-16 C752 A-16 C753 A-16 C754 A-16 C755 A-16 C757 A-16 C758 A-16 C759 B-17 C760 B-17 C761 B-16 C762 B-17 C763 B-17 C764 B-17 C765 A-17 C766 A-17 C767 B-17 C768 B-17 C769 A-18 C770 A-18 C771 B-17 C772 A-18 C773 B-17 C774 A-17 C775 A-17 C777 A-18 C778 A-18 C781 A-18 C824 A-10 C825 A-12 C826 A-12

C827 A-11 C828 A-11 C829 A-11 C830 A-11 C831 A-12 C832 A-11 C833 A-11 C834 A-11 C835 A-11 C837 A-10

CN904 B-18 CN909 G-15 CN910 D-10

D001 C-14 D201 E-11 D202 E-11 D371 C-15 D502 E-13 D604 G-11 D608 F-10 D609 F-11 D611 E-10 D614 F-11 D615 F-11

FB151 C-16 FB152 E-15 FB202 G-13 FB204 G-12 FB205 E-12 FB402 C-11 FB501 E-15 FB503 E-14 FB504 D-14 FB505 D-14 FB701 A-13 FB702 A-13

IC151 C-17 IC152 E-15 IC201 G-14 IC204 F-13 IC371 D-15 IC401 C-11 IC501 E-14 IC552 F-14 IC602 F-11 IC603 F-10 IC701 B-12 IC751 A-17 IC802 A-11

L005 C-14 L007 A-15 L008 B-16 L010 B-16 L011 B-16 L015 B-15 L017 C-14 L019 A-16 L020 A-14 L152 C-18 L153 C-16 L154 C-16 L155 B-18 L156 D-15 L201 E-10 L202 D-13 L203 E-13 L206 E-12 L209 E-13 L501 D-13 L552 F-15 L553 F-15 L701 A-13 L702 B-13 L704 A-13 L751 B-17 L752 B-17 L753 B-17

Q001 B-14 Q002 B-14 Q012 B-14

Q016 B-15 Q017 A-15 Q020 B-15 Q021 A-16 Q023 A-16 Q025 B-16 Q026 B-15 Q030 B-15 Q032 B-15 Q038 B-15 Q039 C-15 Q041 C-14 Q042 C-15 Q045 D-14 Q109 C-15 Q151 C-16 Q153 C-16 Q154 C-16 Q156 C-16 Q202 D-11 Q203 E-11 Q301 B-18 Q302 B-18 Q305 B-18 Q306 B-18 Q307 A-18 Q308 B-18 Q309 B-18 Q371 C-16 Q372 D-16 Q607 G-11 Q619 F-11 Q620 F-10 Q701 B-13 Q702 B-13 Q703 A-13 Q704 A-13 Q705 A-13 Q804 A-10 Q805 A-10

R003 B-14 R005 B-14 R006 B-14 R007 B-14 R008 B-14 R009 B-14 R015 B-14 R020 B-14 R021 B-14 R023 B-15 R025 B-14 R027 B-15 R029 A-15 R031 A-14 R032 B-14 R034 C-14 R037 B-14 R040 B-15 R041 B-14 R042 B-15 R047 B-14 R048 B-14 R049 A-15 R050 A-15 R051 A-15 R052 B-14 R053 D-14 R053 D-14 R054 D-14 R055 B-14 R057 B-15 R059 D-13 R060 C-14 R062 B-15 R066 B-16 R067 A-15 R068 A-16 R069 A-16 R070 A-16 R076 B-16 R077 B-16 R078 B-16 R079 B-16 R080 B-15 R083 B-15

R084 B-15 R087 C-15 R094 B-15 R095 C-15 R104 B-15 R105 B-15 R106 B-15 R109 C-14 R110 C-14 R112 C-15 R152 C-16 R154 C-16 R157 C-16 R161 C-16 R162 C-16 R176 C-18 R177 B-17 R178 B-17 R179 B-17 R180 B-17 R202 D-11 R204 D-11 R205 D-11 R208 E-11 R210 E-11 R211 D-11 R223 E-11 R224 E-11 R226 E-12 R240 E-12 R244 E-11 R245 E-12 R246 E-11 R247 E-11 R248 E-11 R249 E-11 R250 G-12 R254 C-11 R257 E-13 R302 A-18 R303 B-18 R304 B-18 R305 A-18 R311 B-18 R314 A-18 R315 A-18 R316 B-18 R366 C-15 R371 C-16 R372 D-16 R373 D-15 R374 D-15 R375 C-16 R376 D-15 R377 C-15 R378 D-16 R379 D-15 R382 C-15 R383 C-15 R384 D-14 R385 C-15 R388 C-16 R389 C-15 R390 C-15 R402 B-12 R403 B-11 R404 B-12 R408 C-12 R412 C-12 R414 B-11 R415 B-11 R419 C-11 R424 B-11 R426 B-11 R427 B-11 R428 B-11 R429 B-11 R430 B-11 R431 C-11 R502 E-15 R503 E-15 R504 F-14 R508 E-14 R510 D-14 R511 D-14 R512 D-13

R521 D-14 R526 D-14 R527 D-14 R530 F-14 R603 G-11 R604 G-11 R607 E-10 R608 G-11 R612 F-11 R618 F-10 R619 F-10 R620 G-10 R621 F-10 R624 G-10 R625 F-10 R627 F-10 R627 G-11 R629 F-10 R630 F-11 R631 G-10 R632 G-10 R633 E-11 R634 E-10 R635 F-11 R636 F-10 R637 G-11 R638 G-11 R639 G-11 R640 G-11 R641 G-11 R642 G-11 R643 F-11 R644 G-11 R646 F-11 R647 F-11 R648 F-11 R649 G-11 R651 G-11 R652 F-11 R653 F-11 R654 F-11 R655 F-12 R662 E-11 R663 F-11 R665 F-11 R675 F-11 R676 F-11 R677 F-11 R678 G-11 R679 G-10 R680 G-10 R686 F-11 R687 F-11 R689 F-11 R692 G-10 R699 D-11 R700 E-10 R701 B-13 R702 B-13 R703 B-14 R704 B-13 R705 B-13 R706 B-14 R707 B-13 R708 B-13 R709 B-14 R710 A-13 R711 A-13 R712 B-13 R713 B-13 R714 B-13 R715 B-13 R716 A-13 R717 A-13 R718 A-13 R719 A-13 R720 A-13 R721 A-12 R722 A-12 R723 A-12 R724 A-12 R725 B-12 R726 B-12 R752 A-16 R753 A-16 R755 B-16

R756 B-17 R757 B-17 R758 A-16 R759 A-16 R760 B-17 R761 A-16 R762 A-17 R763 A-17 R764 B-17 R765 B-17 R766 A-17 R767 B-17 R768 A-17 R770 A-17 R771 A-17 R772 A-17 R773 A-17 R774 A-18 R775 A-17 R776 A-16 R777 A-16 R810 A-12 R811 A-12 R812 A-12 R816 A-12 R817 A-12 R818 A-12 R819 A-12 R820 A-11 R821 A-12 R822 A-10 R824 A-10 R826 A-11 R827 A-11 R828 A-11 R829 A-11 R830 A-11 R831 A-10 R832 A-10 R833 A-10 R834 A-10 R835 A-10 R916 D-13 R921 B-11 R922 D-10 R923 D-10 R924 D-10 R925 D-10 R926 G-14 R927 G-14 R928 C-12 R929 C-12 R930 D-12 R931 D-11 R934 D-12 R935 D-12 R936 D-12 R937 D-12 R938 E-12 R939 E-12 R940 E-12 R941 E-12 R942 E-12 R943 E-12 R944 E-12 R945 E-12

TH401 B-16

CCD-TRV66E/TRV77E

4-13 4-14

CAMERA PROCESS, REC/PB HEAD AMP, VIDEO PROCESS, AUDIO, SERVO, SYSTEM CONTROL, MODE CONTROL

VC-214

Page 60

CCD-TRV66E/TRV77E

For schematic diagram

• Refer to page 4-11 for printed wiring board.

VC-214

CAMERA REC/PB

CAMERA REC

CAMERA REC

BOARD (1/10)

IC501 5

28.374 MHz

IC501 !¡

14.187 MHz

IC501 @¡

50 nsec

IC501 @§

3.0Vp-p

IC502 !º CAMERA REC LINE REC

72 nsec

IC502 !º PB

72 nsec

IC502 !§ CAMERA REC/PB LINE REC

IC502 @§



CAMERA REC





14.187 MHz

2.9Vp-p

IC501 @•

CAMERA REC

IC502 2 – 9 CAMERA REC/PB LINE REC

72 nsec

7.0Vp-p

2.9Vp-p

!º

IC502 #¢

LINE REC

!¡

IC502 #§ PB

1.2Vp-p

0.5Vp-p

0.3Vp-p

CAMERA PROCESSOR

VC-214 (1/10)

4-17 4-18

Page 61

For schematic diagram

• Refer to page 4-11 for printed wiring board.

• Refer to page 4-23 for waveforms.

CCD-TRV66E/TRV77E

4-19 4-20 4-21 4-22

Y/C PROCESSOR

VC-214 (2/10)

Page 62

CCD-TRV66E/TRV77E

For schematic diagram

• Refer to page 4-11 for printed wiring board.

VC-214

!™

CAMERA REC/PB

!™

LINE REC

!£

CAMERA REC/PB

!£

LINE REC

BOARD (2/10)

IC202 3

IC202 6

0.45Vp-p

0.5Vp-p

0.8Vp-p

IC202 @£

!§

CAMERA REC/PB

!§

IC202 @£

LINE REC

!¶

IC202 @§

CAMERA REC/PB

!¶

IC202 @§

LINE REC

0.3Vp-p

0.1Vp-p

IC202 #¶

!ª

LINE REC

@º

Q217 E

@¡

IC202 $º

0.1 µsec/div

@™

IC202 $¶

LINE REC/PB

0.3Vp-p

0.4Vp-p

!¢

IC202 !£

CAMERA REC

!∞

IC202 !§

CAMERA REC

0.2 µsec

0.9Vp-p

!•

IC202 #£

CAMERA REC/PB

0.4Vp-p

!•

IC202 #£



LINE REC

0.4Vp-p



0.3Vp-p

@£

IC202 ^•

CAMERA REC/PB

1.0Vp-p

@¢

IC202 &™

CAMERA REC/PB

0.9Vp-p

13.325 MHz

14.187 MHz

25 Hz

3.0Vp-p



2.8Vp-p

4-23

FOCUS/ZOOM MOTOR DRIVE

VC-214 (3/10)

4-25 4-26

Page 63

For schematic diagram

• Refer to page 4-11 for printed wiring board.

• Refer to page 4-30 for waveforms.

CCD-TRV66E/TRV77E

4-27 4-28 4-29

REC/PB HEAD AMP

VC-214 (4/10)

Page 64

CCD-TRV66E/TRV77E

For schematic diagram

• Refer to page 4-11 for printed wiring board.

VC-214

@∞

CAMERA REC

@§

CAMERA REC

@¶

@•

CAMERA REC

BOARD (4/10)

CN001 !§, Q001 C

7.14 MHz

IC001 1

0.1 µsec/div

IC001 !¢

1 µsec/div, 0.2 V/div

IC001 @¶,#¢

9.0Vp-p

0.3Vp-p

VC-214

#º

CAMERA REC/PB

#º

LINE REC

#¡

CAMERA REC/PB

#¡

LINE REC

BOARD (5/10)

IC151 3

IC151 5

0.48Vp-p

0.5Vp-p

0.3Vp-p

#∞

IC151 @ª

CAMERA REC/PB

#§

IC151 #¶

LINE REC

17.7343 MHz

#¶

IC151 $¢

LINE REC

#•

IC151 $§

LINE REC

2Vp-p

0.26Vp-p

0.16Vp-p

0.2 µsec/div, 1 V/div

@ª

IC001 $¶

CAMERA REC

1 µsec/div, 0.1 V/div

#™



IC151 !¶

CAMERA REC/PB

#£

IC151 @∞

CAMERA REC/PB

#¢

IC151 @¶ CAMERA REC/PB IR ON

0.4Vp-p

0.12Vp-p

0.06Vp-p

0.5Vp-p

#ª

IC151 ^º

LINE REC

$º

IC151 ^™

LINE REC

$¡

IC151 ^¢

LINE REC

0.52Vp-p

0.4Vp-p

0.48Vp-p

0.3Vp-p

VIDEO/INTERFACE

VC-214 (5/10)

4-30 4-31 4-32

Page 65

For schematic diagram

• Refer to page 4-11 for printed wiring board.

CCD-TRV66E/TRV77E

VC-214

$™

CAMERA REC/PB

$£

CAMERA REC/PB IR ON

$¢

CAMERA REC/PB IR ON

BOARD (6/10)

IC751 7

4.43 MHz

IC751 @™

0.5 µsec/div

IC751 $¡

0.2Vp-p

0.22Vp-p

4-33 4-34

IR TRANSMITTER

VC-214 (6/10)

Page 66

CCD-TRV66E/TRV77E

For schematic diagram

• Refer to page 4-11 for printed wiring board.

VC-214

CAMERA REC/PB

$∞

$§



BOARD (7/10)

IC402 1

20.0 MHz

IC402 $¶

25 Hz

1.7Vp-p

2.8Vp-p

MODE CONTROL

VC-214 (7/10)

4-37 4-384-36

Page 67

CCD-TRV66E/TRV77E

For schematic diagram

• Refer to page 4-11 for printed wiring board.

VC-214

CAMERA REC/PB

$¶

$•



$ª



BOARD (8/10)

IC801 1,2,@ª

150 Hz

IC801 !¡

25 Hz

IC801 !•

150 Hz

FP-249 (S/T REEL SENSOR), FP-356 (TOP SENSOR), FP-355 (TAPE LED) FLEXIBLE BOARD

PRINTED WIRING BO ARD

— Ref. No. FP-249, 356, 355 FLEXIBLE board; 5,000 series —

1.2Vp-p

2.8Vp-p

%º

IC802 7



%¡

IC802 9

1.0 msec/div

10.3 µsec

100mV

0.1Vp-p

4-39 4-40 4-41

SERVO

VC-214 (8/10)

S/T REEL SENSOR, TOP SENSOR, TAPE LED

FP-249, FP-356, FP-355

Page 68

CCD-TRV66E/TRV77E

VL-23 (VIDEO LIGHT) PRINTED WIRING BOARD (TRV66E only)

— Ref. No. VL-23 Board; 2,000 Series —

VC-214

BOARD (9/10)

CAMERA REC/PB

%™

IC604 $º

20.0 MHz

%£

IC604 %£



32.768 KHz

For schematic diagram

• Refer to page 4-11 for printed wiring board.

3.2Vp-p

For printed wiring boards

• Chip parts Transistor

There are few cases that the part printed on this diagram isn’t mounted in this model.

(TRV66E)

VF-129 (B/W EVF)

DD-117 (DC/DC CONVERTER)

SE-83 (STEADY SHOT)

CD-209 (CCD IMAGER)

MA-351 STEREO MIC AMP, LASER LINK

PJ-92 (AV IN/OUT)

VL-23 (VIDEO LIGHT)

VL-23 BOARD

C151 A-2 C152 A-4 C153 A-2

CN151 A-3 D151 A-4

D152 A-2 D153 A-2

L151 A-2 Q151 A-2

Q152 A-4 R151 A-4

R152 A-2 R153 A-2 R154 A-3

VIDEO LIGHT

VL-23

HI CONTROL

VC-214 (9/10)

4-43 4-44 4-45 4-46

Page 69

For schematic diagram

• Refer to page 4-11 for printed wiring board.

CCD-TRV66E/TRV77E

4-47 4-48 4-49

AUDIO

VC-214 (10/10)

Page 70

CCD-TRV66E/TRV77E

SE-83 BOARD

C451 B-5 C452 D-6 C453 C-2 C454 E-2 C457 C-6 C458 C-6 C459 C-6 C460 D-3 C461 C-6 C462 C-3 C463 D-6 C464 B-6 C465 B-6 C466 C-5 C467 A-2 C468 A-2 C469 A-2 C470 A-2

CN451 A-3 D451 A-2

D452 A-2 IC451 C-6 J451 A-1 L451 B-3

L453 A-2 L454 A-2

R451 B-5 R452 D-6 R453 D-6 R454 B-5 R456 C-6 R457 C-6 R458 C-6 R459 C-6 R460 C-5 R461 B-6

SE451 B-3 SE452 E-3

SE-83 (STEADY SHOT), PJ-92 (AV IN/OUT) PRINTED WIRING BOARDS

— Ref. No. SE-83, PJ-92 Board; 2,000 Series —

PJ-92 BOARD

C101 C-5 C102 D-4 C103 B-5 C104 C-5 C105 A-4 C106 B-4 C107 B-5 C108 A-4 C109 F-4 C110 E-5 C111 A-5

CN101 C-4 D101 A-4

D102 C-5 D103 C-5 D104 E-5 D105 E-5 D106 E-4

J101 D-2 L101 C-4

L102 C-5 L103 B-4 L104 B-4

Q101 E-4 Q102 D-4

R101 D-5 R102 D-4 R103 D-5 R104 D-4 R105 D-4 R106 E-5 R107 F-4 R108 E-5 R109 C-4

STEADY SHOT

SE-83

AV IN/OUT

PJ-92

VF-129 (B/W EVF)

DD-117 (DC/DC CONVERTER)

SE-83 (STEADY SHOT)

CD-209 (CCD IMAGER)

MA-351 STEREO MIC AMP, LASER LINK

PJ-92 (AV IN/OUT)

VL-23 (VIDEO LIGHT)

(TRV77E)(TRV66E)

VF-129 (B/W EVF)

CD-209 (CCD IMAGER)

For printed wiring boards

• Chip parts Transistor Diode

BE321

There are few cases that the part printed on this

DD-117 (DC/DC CONVERTER)

SE-83 (STEADY SHOT)

PJ-92 (AV IN/OUT)

MA-351 STEREO MIC AMP, LASER LINK

diagram isn’t mounted in this model.

4-50 4-51 4-52

Page 71

CCD-TRV66E/TRV77E

4-53 4-54

STEADY SHOT

SE-83

AV IN/OUT

PJ-92

Page 72

CCD-TRV66E/TRV77E

MA-351 BOARD

C301 A-6 C302 A-6 C303 B-5 C304 A-5 C305 B-6 C306 B-4 C333 C-8 C334 C-8 C335 C-8 C336 D-8 C337 C-7 C338 C-7 C339 C-7 C340 C-7 C341 C-2 C342 C-7 C343 C-7 C344 C-1 C345 C-7 C346 D-8 C347 C-2 C348 D-7 C349 D-7 C350 D-2 C351 D-8 C352 D-7 C353 D-7 C354 D-7 C355 D-2 C356 C-6 C356 C-6 C357 C-6 C357 C-6 C358 C-2 C359 C-2 C360 C-7 C361 C-7 C362 D-2 C363 D-2 C364 D-2 C365 D-2 C366 D-2 C367 D-2 C368 D-2 C369 C-6 C370 D-2 C371 C-6 C372 C-6 C373 D-2 C374 C-6 C375 D-2 C376 C-6 C377 A-7 C378 D-2

CN301 B-6 CN302 B-7 CN303 B-5

D301 A-3 D302 A-3 D303 B-2 D305 B-4 D307 D-2 D308 B-4 D309 A-3 D321 C-1 D322 A-2 D323 A-7 F301 A-6

IC301 A-4 IC322 C-7

J301 B-1 L301 B-6 Q301 A-5

Q302 B-5 Q303 B-6 Q304 A-7 Q305 A-5

R301 A-5 R302 B-5 R303 A-5 R304 B-6 R305 B-6 R306 B-4 R307 B-3 R309 D-8 R310 A-7 R311 B-5 R312 A-6 R313 A-5 R314 B-5 R315 A-5 R321 C-1 R322 B-7 R323 B-7 R324 B-2 R335 C-8 R336 C-8 R337 C-8 R338 C-8 R339 C-2 R340 C-7 R341 C-2 R342 C-2 R343 C-2 R344 C-2 R345 D-7 R346 C-7 R347 D-7 R348 D-2 R349 D-2 R350 C-2 R351 C-2 R352 C-7 R353 D-2 R354 D-2 R355 D-2 R356 D-2 R357 D-2 R358 D-2 R359 C-6 R360 C-7 R361 D-2 R362 D-2 R363 D-2 R364 C-2 R365 C-2 R366 C-2 R367 C-2 R368 D-2 R369 C-2

S301 D-1 S302 D-7 S303 C-6

MA-351 (STEREO MIC AMP, LASER LINK) PRINTED WIRING BOARD

— Ref. No. MA-351 Board; 2,000 Series —

For printed wiring boards

• Chip parts Transistor

VF-129 (B/W EVF)

CD-209 (CCD IMAGER)

VL-23 (VIDEO LIGHT)

(TRV77E)(TRV66E)

VF-129 (B/W EVF)

CD-209 (CCD IMAGER)

There are few cases that the part printed on this diagram isn’t mounted in this model.

DD-117 (DC/DC CONVERTER)

SE-83 (STEADY SHOT)

MA-351 STEREO MIC AMP, LASER LINK

PJ-92 (AV IN/OUT)

DD-117 (DC/DC CONVERTER)

SE-83 (STEADY SHOT)

PJ-92 (AV IN/OUT)

MA-351 STEREO MIC AMP, LASER LINK

STEREO MIC AMP, LASER LINK

MA-351

4-55 4-56

Page 73

CCD-TRV66E/TRV77E

4-57 4-58 4-59

STEREO MIC AMP, LASER LINK

MA-351

Page 74

CCD-TRV66E/TRV77E

PD-105 BOARD

C5501 B-5 C5502 B-4 C5503 C-8 C5504 A-4 C5505 A-4 C5506 B-8 C5507 A-9 C5508 B-8 C5509 B-9 C5511 C-8 C5512 C-7 C5513 C-7 C5514 C-8 C5515 C-8 C5516 C-8 C5517 C-7 C5518 C-9 C5519 A-8 C5520 C-9 C5521 C-9 C5601 B-8 C5603 B-4 C5604 C-3 C5605 C-4 C5607 B-4 C5608 C-3 C5610 C-4 C5612 B-5 C5616 C-3 C5618 D-3 C5619 D-8 C5620 D-5 C5621 C-8 C5622 C-5 C5623 C-8 C5624 B-9 C5625 B-8 C5633 B-3 C5701 D-3 C5702 D-3 C5703 C-9 C5704 C-1 C5705 C-1 C5706 C-10 C5801 A-10

CN5501 B-5 CN5601 D-5 CN5701 D-1 CN5801 A-3 CN5802 A-2 CN5803 A-3 CN5804 A-5 CN5805 A-1

D5601 B-4 D5604 C-5 D5605 B-4 D5701 A-11 D5702 A-11 D5703 D-11 D5704 D-2

IC5501 B-5 IC5502 C-8 IC5601 C-4 IC5602 C-3 IC5701 C-10 IC5801 A-10

L5501 A-9 L5502 A-8 L5503 A-8

L5504 C-9 L5601 A-8 L5603 A-4 L5604 A-8 L5605 C-4 L5701 D-2

Q5501 C-8 Q5601 B-4 Q5602 B-4 Q5605 C-3 Q5606 C-3 Q5607 C-3 Q5608 C-3 Q5701 C-9 Q5702 C-10

R5501 B-8 R5502 B-8 R5505 B-8 R5508 B-7 R5509 B-7 R5510 B-9 R5511 B-9 R5512 B-7 R5513 B-8 R5516 B-8 R5517 B-7 R5518 B-7 R5519 C-9 R5520 C-9 R5521 B-8 R5522 B-8 R5528 C-9 R5531 C-8 R5532 C-9 R5537 C-5 R5541 D-8 R5542 D-9 R5544 C-8 R5545 B-9 R5602 C-8 R5603 D-3 R5604 D-9 R5605 C-7 R5606 C-5 R5607 B-7 R5608 C-5 R5610 B-4 R5612 B-4 R5613 B-4 R5615 B-3 R5617 B-4 R5619 B-4 R5620 B-3 R5621 C-3 R5622 B-3 R5623 B-3 R5624 B-3 R5625 C-5 R5626 C-4 R5627 B-5 R5628 C-5 R5629 B-3 R5630 B-3 R5631 C-4 R5632 B-4 R5637 C-5 R5640 C-3 R5641 C-9 R5643 C-9 R5644 C-3 R5646 C-5

R5647 D-8 R5648 D-5 R5651 D-8 R5652 D-8 R5653 D-4 R5654 D-3 R5657 C-4 R5658 D-4 R5659 D-4 R5660 D-4 R5661 D-5 R5663 D-4 R5664 D-5 R5665 D-5 R5666 D-7 R5667 D-7 R5668 D-7 R5669 D-7 R5670 D-7 R5671 D-4 R5672 D-4 R5673 D-7 R5674 D-8 R5676 D-7 R5678 D-4 R5679 D-8 R5680 D-8 R5681 D-8 R5682 D-7 R5683 D-8 R5684 D-8 R5685 D-9 R5686 C-9 R5688 C-4 R5692 B-4 R5693 B-4 R5694 B-3 R5695 B-3 R5696 D-5 R5697 C-5 R5698 D-3 R5699 D-4 R5701 A-11 R5702 A-11 R5703 C-9 R5704 C-10 R5705 C-10 R5706 C-10 R5707 D-1 R5708 C-11 R5709 D-1 R5710 C-10 R5801 C-7 R5802 C-7 R5803 A-7 R5804 A-7 R5805 A-11 R5806 A-7 R5807 B-2 R5808 B-3 R5809 B-2 R5810 B-3 R5811 A-10 R5812 A-10

S5801 D-7 S5802 C-7 S5803 B-7 S5804 A-7

T5701 C-2

PD-105 (RGB DECODER, LCD, TIMING GENERATOR, BACK LIGHT DRIVE) PRINTED WIRING BOARD

— Ref. No. PD-105 Board; 10,000 Series —

(TRV66E/TRV77E)

CF-56 (USER CONTROL)

PD-105 RGB DECODER, LCD, TIMING GENERATOR, BACK LIGHT DRIVE

VC-214 CAMERA PROCESSOR, Y/C PROCESSOR, FOCUS/ZOOM MOTOR DRIVE, REC/PB HEAD AMP , VIDEO/INTERFACE, IR TRANSMITTER, MODE CONTROL, SERVO, HI CONTROL, SYSTEM CONTROL, AUDIO PROCESSOR

For printed wiring boards

• This board is four-layer print board. However, the patterns of layers two to three have not been included in the diagram.

• Chip parts Transistor

There are few cases that the part printed on this diagram isn’t mounted in this model.

RGB DECODER, LCD, TIMING GENERATOR, BACK LIGHT DRIVE

PD-105

4-61 4-62

Page 75

CCD-TRV66E/TRV77E

PD-105

CAMERA REC/PB



BOARD (1/2)

IC5801 2

23.78 KHz

IC5502 8

IC5502 9

IC5502 !º

3.0Vp-p

0.4Vp-p

0.3Vp-p

IC5502 @º



IC5502 @™

IC5502 @¢



0.1Vp-p

2.0Vp-p

4-63 4-64

RGB DECODER, LCD

PD-105 (1/2)

4-65

Page 76

CCD-TRV66E/TRV77E

For schematic diagram

• Refer to page 4-60 for printed wiring board.

PD-105

CAMERA REC/PB



!º



BOARD (2/2)

IC5601 @§

5.48 MHz

IC5601 #¶

IC5602 7

6.7 KHz

3.0Vp-p

2.8Vp-p

5.0Vp-p

4-66

TIMING GENERATOR, BACK LIGHT DRIVE

PD-105 (2/2)

4-67 4-68

Page 77

VF-129 (B/W EVF) PRINTED WIRING BOARD

CD-209 (CCD IMAGER)

(TRV77E)(TRV66E)

VL-23 (VIDEO LIGHT)

MA-351 STEREO MIC AMP, LASER LINK

PJ-92 (AV IN/OUT)

SE-83 (STEADY SHOT)

DD-117 (DC/DC CONVERTER)

VF-129 (B/W EVF)

CD-209 (CCD IMAGER)

MA-351 STEREO MIC AMP,

LASER LINK PJ-92 (AV IN/OUT)

SE-83 (STEADY SHOT)

DD-117 (DC/DC CONVERTER)

VF-129 (B/W EVF)

— Ref. No. VF-129 Board; 3,000 Series —

VF-129 BOARD

C901 A-3 C902 A-3 C903 A-2 C904 B-2 C905 A-3 C906 A-2 C907 A-1 C908 C-2 C909 B-1 C910 C-3 C911 C-3 C912 B-3 C913 A-2 C914 D-3 C915 E-3 C916 C-3

CN901 B-3 CN902 B-1

D901 A-1 D903 D-3

IC901 A-1 L901 B-1

L902 B-3 L903 D-1

Q901 A-2 Q902 B-2 Q903 C-3 Q904 C-2

R901 A-3 R902 A-3 R903 A-1 R904 A-3

R905 A-2 R906 A-2 R907 B-1 R908 B-2 R909 B-2 R910 B-2 R911 A-3 R912 A-2 R913 C-2 R914 C-2 R915 B-1 R916 A-1 R917 A-1 R918 C-2 R919 C-2 R920 C-2 R921 D-2 R922 E-1 R923 E-3 R924 C-3 R925 C-3 R926 D-2 R927 B-1 R928 B-1 R929 A-1 R930 C-1 R931 C-1 R932 C-1

RV903 C-2 RV904 D-1

T901 D-1 T902 D-1

TH901 B-2 W901 D-2

CCD-TRV66E/TRV77E

VF-129

CAMERA REC/PB



BOARD

IC901 1,5

2.0Vp-p

20 msec

IC901 3

2.0Vp-p

20 msec

IC901 7

1.1Vp-p

20 msec

IC901 !¡

For printed wiring boards

• Chip parts Transistor

IC901 !£

IC901 !§



0.9Vp-p

1.1Vp-p

2.4Vp-p

There are few cases that the part printed on this diagram isn’t mounted in this model.

4-69 4-70 4-71

B/W EVF

VF-129

Page 78

CCD-TRV66E/TRV77E

CF-56 BOARD

BH001 D-5 C001 D-10

C002 D-10 C003 D-12

CN001 B-11 CN002 A-14 CN003 E-11 CN006 B-14 CN007 C-12 CN008 E-12 CN009 C-14 CN101 D-13

D001 D-11 D003 B-8 D004 A-4 D005 D-10 D006 D-10 D007 A-5 D008 D-10 D012 A-13 D013 C-11

Q001 D-12 Q003 C-10 Q005 C-10

R003 C-10 R005 A-4 R006 A-12 R007 B-9 R008 B-4 R009 C-9 R013 A-4 R015 C-9

R016 B-4 R020 B-5 R022 A-5 R023 A-5 R025 C-9 R026 B-6 R029 B-12 R031 E-9 R032 B-6 R036 B-12 R037 B-5 R038 E-9 R039 B-13 R040 B-5 R041 E-9 R049 C-10 R050 C-10 R051 C-10 R052 C-10 R053 E-9

S001 A-3 S003 B-3 S004 C-8 S006 A-5 S008 B-4 S010 B-6 S012 C-8 S013 B-6 S015 A-7 S017 D-8 S018 A-6 S021 B-3 S022 B-5 S024 B-13 S027 E-8

CF-56 (USER CONTROL) PRINTED WIRING BOARD

— Ref. No. CF-56 Board; 2,000 Series —

USER CONTROL

CF-56/MR-8500

(TRV66E/TRV77E)

CF-56 (USER CONTROL)

For printed wiring boards

• Chip parts Transistor Diode

PD-105 RGB DECODER, LCD, TIMING GENERATOR, BACK LIGHT DRIVE

BE321

There are few cases that the part printed on this diagram isn’t mounted in this model.

VC-214 CAMERA PROCESSOR, Y/C PROCESSOR, FOCUS/ZOOM MOTOR DRIVE, REC/PB HEAD AMP , VIDEO/INTERFACE, IR TRANSMITTER, MODE CONTROL, SERVO, HI CONTROL, SYSTEM CONTROL, AUDIO PROCESSOR

4-72 4-73 4-74

Page 79

CCD-TRV66E/TRV77E

4-75 4-76 4-77

USER CONTROL

CF-56/MR-8500

Page 80

CCD-TRV66E/TRV77E

For printed wiring boards

• This board is four-layer print board. However, the pat-

• Chip parts

VF-129 (B/W EVF)

DD-117 (DC/DC CONVERTER)

SE-83 (STEADY SHOT)

terns of layers two to three have not been included in the diagram.

Transistor

There are few cases that the part printed on this diagram isn’t mounted in this model.

CD-209 (CCD IMAGER)

MA-351 STEREO MIC AMP, LASER LINK

PJ-92 (AV IN/OUT)

VL-23 (VIDEO LIGHT)

(TRV77E)(TRV66E)

VF-129 (B/W EVF)

DD-117 (DC/DC CONVERTER)

SE-83 (STEADY SHOT)

CD-209 (CCD IMAGER)

MA-351 STEREO MIC AMP,

LASER LINK PJ-92 (AV IN/OUT)

DD-117 BOARD

C801 E-8 C802 E-8 C803 D-7 C804 E-7 C805 D-7 C806 E-7 C807 D-7 C808 D-8 C809 D-7 C810 D-8 C811 D-7 C812 D-8 C813 D-7 C814 E-3 C815 C-8 C816 E-4 C817 E-4 C818 F-8 C819 C-7 C820 C-7 C821 C-7 C822 E-4 C823 C-8 C824 C-7 C825 B-7 C826 D-4 C827 E-7 C828 E-6 C829 E-6 C830 D-7 C831 E-7 C832 B-7 C833 B-7 C834 C-8 C836 B-7 C837 C-7 C838 C-7 C840 D-3 C841 B-8 C842 A-1 C843 B-8 C844 A-8 C846 B-8 C847 B-2 C848 B-3 C849 A-7 C850 A-8 C851 B-8 C852 B-3 C853 B-3 C854 B-8 C855 A-7 C856 E-7 C857 A-7 C860 A-1 C861 A-2 C862 A-6 C863 B-1 C864 B-2 C865 A-1 C866 A-1 C867 A-2 C868 A-1 C869 A-1 C870 E-7 C871 B-6 C872 F-8 C873 A-6 C874 A-3 C875 A-7 C876 D-2 C877 D-2 C878 B-7

CN801 C-1 CN931 C-9 CN933 A-9 CN934 D-4 CN935 G-3 CN936 F-1

D806 B-7 D809 B-2 D810 B-7 D812 B-7 D813 C-8 D814 F-9 D815 F-8 D816 E-8 D817 C-8 D818 D-6 D819 E-7 D820 B-2 D821 B-2 D822 F-8 D932 G-7 D933 F-8 D934 G-7 D935 F-8 D936 G-7 D938 E-4

FB931 D-4 FB932 E-4 FB933 D-4

IC801 D-7 IC802 E-7

L801 D-2 L802 D-3 L803 D-3 L804 E-4 L805 B-3 L806 C-3 L807 C-2 L808 B-3 L809 C-3 L810 B-8 L811 B-8 L812 B-8 L813 B-8 L814 A-7 L815 A-7 L816 B-8 L817 A-8 L818 A-7 L819 A-8 L820 D-3 L821 A-1 L822 A-6

LF801 D-2 PS801 F-8

PS802 F-7 PS803 F-7 PS804 F-7 PS805 F-7 PS806 F-7 PS807 F-8

Q801 F-8 Q803 E-8 Q804 F-8 Q805 F-8 Q806 C-6 Q807 C-8 Q808 C-8 Q809 B-7 Q810 C-7 Q812 C-8 Q813 C-7 Q814 C-7 Q815 C-7 Q817 C-7 Q819 D-4 Q820 E-7 Q823 B-7 Q824 E-7 Q826 A-3 Q827 A-7

Q828 B-1 Q829 A-1 Q830 B-2 Q831 A-2 Q832 B-1 Q833 A-7 Q834 B-1 Q835 A-3 Q836 A-4 Q837 A-2 Q838 A-3 Q839 A-4 Q840 A-3 Q841 A-2 Q842 A-2 Q843 A-2 Q844 A-4 Q845 A-3 Q846 A-2 Q847 A-2 Q848 A-3 Q849 A-3 Q850 A-3 Q851 E-8 Q852 B-6 Q853 B-7 Q854 B-7 Q855 B-7 Q856 A-1 Q932 G-8 Q933 G-8 Q934 G-8

R801 E-7 R802 D-8 R803 D-8 R804 D-8 R805 D-7 R806 E-7 R807 D-7 R808 D-8 R809 D-8 R810 D-7 R811 D-7 R812 D-7 R813 F-8 R814 D-8 R815 D-8 R816 D-8 R817 D-8 R818 D-7 R819 D-7 R820 D-8 R821 D-7 R822 E-8 R824 D-7 R825 D-8 R826 D-8 R827 E-8 R828 E-8 R829 D-7 R830 D-7 R831 F-8 R832 D-8 R833 D-7 R834 D-7 R835 D-8 R836 D-8 R837 D-7 R838 D-8 R839 C-7 R840 C-8 R841 C-8 R842 E-6 R843 C-7 R844 D-2 R845 D-6 R846 D-2 R847 E-7 R849 E-6 R850 E-6

R852 D-6 R853 D-6 R854 D-6 R859 E-7 R864 E-7 R865 B-7 R866 B-7 R867 E-7 R868 A-6 R870 A-3 R871 A-3 R872 B-2 R873 A-1 R874 B-1 R875 A-6 R876 B-1 R877 A-3 R878 A-7 R879 B-1 R880 B-1 R881 B-1 R882 B-1 R883 B-3 R884 B-4 R885 A-2 R887 B-3 R888 B-3 R889 A-2 R890 A-2 R891 A-3 R892 A-3 R893 A-3 R894 A-2 R895 A-1 R896 A-4 R897 A-4 R898 A-2 R899 A-2 R900 A-2 R901 A-1 R902 A-1 R903 A-3 R904 A-3 R905 A-3 R906 A-3 R907 A-3 R908 B-7 R910 B-7 R911 B-7 R912 B-7 R913 F-8 R914 D-7 R915 E-6 R916 A-2 R917 A-3 R918 A-6 R919 A-2 R920 A-2 R921 D-3 R922 D-2 R923 D-3 R924 B-1 R925 A-4 R926 C-9 R932 G-8 R933 F-2 R934 F-2 R935 F-2 R936 F-2 R937 F-2 R938 F-2 R939 F-2 R940 G-8 R941 G-8 R942 E-4 R943 G-7 R944 B-1 R945 B-1

T801 B-2

DD-117 (DC/DC CONVERTER) PRINTED WIRING BOARD

— Ref. No. DD-117 Board; 2,000 Series —

DC/DC CONVERTER

DD-117

4-78 4-79 4-80

Page 81

CCD-TRV66E/TRV77E

DD-117

CAMERA REC/PB



BOARD

IC801 4

2 µsec

IC801 ^¢

2 µsec

0.75Vp-p

4-81 4-82 4-83 4-84

DC/DC CONVERTER

DD-117

Page 82

CCD-TRV66E/TRV77E

CONTROL SWITCH BLOCK

FK-8500/SS-8500

4-88E

Page 83

SECTION 5

ADJUSTMENTS

5-1. CAMERA SECTION ADJUSTMENT

1-1. PREPARATIONS BEFORE ADJUSTMENT (CAMERA SECTION)

1-1-1. List of Service Tools

• Oscilloscope • Color monitor • Vectorscope

• Regulated power supply • Digital voltmeter

CCD-TRV66E/TRV77E

Ref. No.

J-1

Filter for color temperature correction (C14) ND filter 1.0

J-2

ND filter 0.3

J-3

Pattern box PTB-450

J-4

Color chart for pattern box Adjustment remote commander (RM-95 upgraded).

J-5

(Note 2)

J-6

Siemens star chart

J-7

Clear chart for pattern box

J-8

Multi CPC jig

J-9

CPC-7 jig

J-10

Power cord (Note 2)

J-11

AFM DEV jig

J-12

Extension cable (16P, 0.5mm)

J-13

Extension cable (70P, 0.5mm)

J-14

IR receiver jig

Note 1: If the micro processor IC in the adjustment remote commander is

not the new micro processor (UPD7503G-C56-12), the pages cannot be switched. In this case, replace with the new micro processor (8-759-148-35).

Name

Parts Code

J-6080-058-A J-6080-808-A

J-6080-818-A J-6082-200-A J-6020-250-A

J-6082-053-B

J-6080-875-A J-6080-621-A J-6082-311-A J-6082-382-A J-6082-223-A J-6082-312-A

J-6082-357-A

J-6082-439-A J-6082-383-A

Auto white balance adjustment/check White balance adjustment/check

White balance check White balance check

For checking the flange back

For adjusting the LCD block For adjusting the video section For connecting the battery terminal and DC power supply For adjusting the deviation For extension between the CD-209 board (CN1401) and

the VC-214 board (CN501) For extension between the DD-117 board (CN931) and

the VC-214 board (CN914) For adjusting the IR transmitter

Note 2: Connect the adjustment remote commander to the LANC jack,

and set to HOLD switch to the “ADJ” side.

Usage

J-1 J-2

J-6

J-11 J-12 J-13 J-14

J-7 J-8

J-3

J-4 J-5

J-9 J-10

Fig. 5-1-1.

5-1

Page 84

1-1-2. Adjusting items when replacing main parts

When replacing main parts, adjust the items indicated by r in the following table.

Replacing parts

Adjustment Section

Camera Camera Camera Camera Camera Camera Camera Camera

Camera EVF

EVF EVF EVF EVF EVF LCD LCD LCD LCD LCD LCD LCD LCD LCD System Control Servo Servo Video Video Video Video Video Video Video Video Video IR IR IR Audio Audio Audio Mechanism

Adjusting item

Initialization of D, E, F page data HALL adj. Flange back adj. AGC gain calibration adj. Color reproduction adj. IRIS IN/OUT adj. MAX GAIN adj. Auto white balance standard data input Auto white balance adj. Angular velocity sensor sensitivity preset and

steady shot check. Centering adj. Focus adj. Aberration adj. Horizontal amplitude adj. Vertical amplitude adj. Brightness adj. LCD initial data input VCO adj. D range adj. Bright adj. Contrast adj. V-COM level adj. Color adj. V-COM adj. White balance adj. Battery end adj. CAP FG offset adj. Switching position adj. 28MHz origin oscillation adj. AFC f0 adj. Filter f0 adj. Y OUT level adj. C OUT level adj. RP filter f0 adj. REC Y current adj. REC L level adj. REC C current adj. IR video carrier frequency adj. IR video deviation adj. IR audio deviation adj.

1.5MHz deviation adj.

1.7MHz deviation adj. BPF f0 adj. Tape path adj.

Lens device

CD-209 board IC1401 (CCD imager)

SE-83 board SE451 (Pitch sensor)

SE-83 board SE452 (Yaw sensor)

VC-214 board IC202 (Y, C process)

VC-214 board IC151 (Y, C IN/OUT)

VC-214 board IC001 (REC/PB AMP)

VC-214 board IC751 (IR transmitter)

VC-214 board IC301 (AFM process)

VC-214 board IC501 (Timing generator)

VC-214 board IC502 (S/H, AGC)

VC-214 board IC401 (EEPROM)

Mechanism deck M901 (Drum assembly)

Mechanism deck M902 (Capstan motor)

VF-129 board IC901 (CRT driver)

VF-129 board T901 (FBT)

EVF block V901 (Picture tube)

PD-105 board IC5502 (LCD driver)

r rr rr r

rrr rrr

rr r r

rrr rrr rrr

rr r

rrr rrr rrr rrr rrr

rrr r rr rr rr rr rr rr rrr rrrr r rr rr

rr rr r rr r

rr rr r rr r rr r

rr r rr r

rr rr rr

Table. 5-1-1.

PD-105 board IC5601 (Timing generator)

LCD block ND901 (Fluorescent tube)

LCD block LCD901 (LCD panel)

5-2

Page 85

1-1-3. Preparations

Note 1: For details of how remove the cabinet and boards, refer to “2.

DISASSEMBLY”.

Note 2: When performing only the adjustments, the lens block and boards

need not be disassembled.

1) Connect the equipment for adjustments according to Fig. 5-1-3.

2) By setting the “Forced Camera Power ON mode”, the camera power can be turned ON even if the front panel block (MA351 board, power switch, microphone unit) has been removed. When removing the front panel block disconnect the following connector.

1. VC-214 board CN903 (20P 0.5mm)

Pattern box

1.5 m

Note 3: As removing the cabinet (R) (removing the VC-214 boar d CN911)

means removing the lithium 3V power supply (CF-56 board BH001), data such as date, time, user-set menus will be lost. After completing adjustments, reset these data. If the cabinet (R) has been removed, the self-diagnosis data, data on history of use (total drum rotation time etc. ) will be lost. Before removing, note down the self-diagnosis data and data on history use (data of page: 2, address: A2 to AA). (Refer to “SELF-DIA GNOSIS FUNCTION” for the self-diagnosis data, and to “5-4. Service Mode” for the data on the history use.)

Note 4: Setting the “Forced Camera Power ON” Mode

1) Select page: 0, address: 01, and set data: 01.

2) Select page: D, address: 10, set data: 01, and press the P AUSE button of the adjustment remote commander. The above procedure will enable the camera power to be turned on with the front panel block removed. After completing adjustments, be sure to exit the “Forced Camera Power ON Mode”.

Note 5: Exiting the “Forced Camera Power ON” Mode

1) Select page: 0, address: 01, and set data: 01.

2) Select page: D, address: 10, set data: 00, and press the P AUSE button of the adjustment remote commander.

3) Select page: 0, address: 01, and set data: 00.

Front of the lens

Fig. 5-1-2.

5-3

Page 86

Note: Press the battery switch of the battery terminal using adhesive tape, etc.

Front panel block

VIDEO jack

PJ-92 board CN101

MA-351 board CN303

Color monitor

Lens block

Need not connected

SE-83 board CN451

To PD-105 board CN5802

Vector scope

CD-209 board

CN1401

CN904

CN903

CN901

Terminated at 75

CN551

CN909

CN501

VC-214 board

CN905

CN001

Ω

Need not connected

Extension cable (16P, 0.5mm) (J-6082-357-A)

CN910

CN914

CN911

CN906

CN908

Extension cable (70P, 0.5mm) (J-6082-439-A)

To CF-56 board CN001

Battery terminal

Battery switch

DC IN jack

CN935

CN936

DD-117 board

CN931

CN801

CN933

Regulated power supply (Note)

0.1Vdc)

(8.4

Adjustment remote commander

Need not connected

CN934

Cabinet (L)

Must be connected when performing the video system adjustments.

CPC-7 jig (J-6082-382-A)

LANC jack

Cabinet (R)

CN5805

CN5701

PD-105 board

CN5601

CN5501

LCD WINDOW

CN5802 CN5803 CN5804

Fig. 5-1-3.

5-4

Multi CPC jig (J-6082-311-A)

Must be connected when performing the LCD system adjustments.

Page 87

1-1-4. Precaution

1. Setting the Switch

Unless otherwise specified, set the switches as follows and perform adjustments without loading cassette.

1. POWER switch (MA-351 board) ...........................CAMERA

2. NIGHT SHOT switch (Lens block) .................................OFF

3. VIDEO LIGHT switch (MA-351 board)

(CCD-TRV66E) ............................................................... OFF

4. DEMO MODE (Menu display) .......................................OFF

5. DIGITAL ZOOM (Menu display) ................................... OFF

6. STEADY SHOT (Menu display) .....................................OFF

7. DISPLAY (Menu display) ................................. V-OUT/LCD

2. Order of Adjustments

Basically carry out adjustments in the order given.

Color bar chart (Color reproduction adjustment frame)

Yellow

AB B

(VIDEO IN/OUT terminal

output waveform)

Cyan

A=B

Fig. a

White

Green

Magenta

Red

Blue

Enlargement

C=D

Difference in level

8. DISPLAY (CF-56 board) .................................................. ON

9. FOCUS switch (MR-8500 block) ......................... MANUAL

10. PROGRAM AE (CF-56 board)....................................... Auto

11. BACK LIGHT (CF-56 board)..........................................OFF

12. PICTURE EFFECT (CF-56 board) ................................. OFF

13. DIGITAL EFFECT (CF-56 board) ..................................OFF

14. 16 : 9 WIDE (MENU display) .........................................OFF

Electronic beam scanning frame

Red

Cyan

White

Green

Yellow

Fig. b (monitor TV picture)

Blue

Magenta

CRT picture frame

3. Subjects

1) Color bar chart (Color reproduction adjustment frame) When performing adjustments using the color bar chart, adjust the picture frame as shown in Fig. 5-1-4. (Color reproduction adjustment frame)

2) Clear chart (Color reproduction adjustment frame) Remove the color bar chart from the pattern box and insert a clear chart in its place. (Do not perform zoom operations during this time.)

3) Flange back adjustment chart Make the chart shown in Fig. 5-1-5. using A0 size (1189mm × 841mm) black and white vellum paper.

Adjust the camera zoom and direction to obtain the output waveform shown in Fig. a and the monitor TV display shown in Fig. b.

Fig. 5-1-4.

White

841m

Black

1189mm

Fig. 5-1-5.

Note: Use matte vellum paper bigger than A0, and make sure the edges of

the black and white paper joined together are not rough.

5-5

Page 88

1-2. INITIALIZATION OF D, E, F PAGE DATA

1. Initializing the D,E,F Page Data

Note: If the D,E,F page data has been initialized, “Modification of D, E, F

Page Data” and all adjustments need to be performed again.

3. D Page Table

Note : Fixed data-1 : Initialized data. (Refer to “1. Initializing the D,E,F

Page Data”.) Fixed data-2 : Modified data. (Refer to “2. Modification of D, E, F Page Data”.)

Adjusting page D Adjusting Address 00 to 6F Adjusting page F Adjusting Address 00 to FF Adjusting page E Adjusting Address 00 to FF

Initializing Method:

1) Select page: 0, address: 01, and set data: 01.

2) Select page: 6, address: 00, and set data: 51.

3) Select page: 6, address: 01, set data: 51, and press the PAUSE button of the adjustment remote commander.

4) Select page: 6, address: 02, and check that the data is 01.

5) Select page: 2, address: 00, and set data: 29.

6) Select page: 2, address: 01, set data: 29, and press the PAUSE button of the adjustment remote commander.

7) Perform “Modification of D,E,F Page Data”.

2. Modification of D, E, F Page Data

If the D, E, F page data has been initialized, change the data of the “Fixed data-2” address shown in the following tables by manual input.

Modifying Method:

1) Before changing the data, select page: 0, address: 01, and set data: 01.

2) New data for changing are not shown in the tables because they are different in destination. When chang ing the data, copy the data built in the same model.

Note: If copy the data built in the different model, the camcorder may

not operate.

3) When changing the data, press the PAUSE button of the adjustment remote commander each time when setting new data to write the data in the non-volatile memory.

4) Check that the data of adjustment addresses is the initial value. If not, change the data to the initial value.

5) After completing “Modification of D, E, F Page Data”, select page: 0, address: 01, and set data: 00. Also perform all adjustments.

Address

00 to 0F

10 11 12 13 14 15 16 17 18

19 1A 1B 1C 1D

29 2A 2B 2C 2D

39 3A 3B 3C 3D

Initial value

88 8D A8

Remark

Test mode Fixed data-1 (Initialized data) Fixed data-2 (Modified data, copy the data built in the same model.) Fixed data-1 (Initialized data)

Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1 (Initialized data)

Fixed data-2 Fixed data-1

Fixed data-2 (Modified data, copy the data built in the same model.) Battery end adj.

Fixed data-1 Fixed data-2 (Modified data, copy the data built in the same model.)

Fixed data-1 (Initialized data)

5-6

Page 89

Address

40 41 42 43 44 45 46 47 48

49 4A 4B 4C 4D 4E 4F

59 5A 5B 5C 5D 5E 5F

69 6A 6B 6C 6D 6E 6F

Initial value

Fixed data-2

Fixed data-1 Fixed data-2 Fixed data-1 (Initialized data)

Fixed data-2

Fixed data-1 Fixed data-2 Fixed data-1 (Initialized data)

Table. 5-1-2.

Remark

4. F Page table

Note : Fixed data-1 : Initialized data. (Refer to “1. Initializing the D,E,F

Page Data”.) Fixed data-2 : Modified data. (Refer to “2. Modification of D , E, F Page Data”.)

Address

Initial value

Remark

00 to 0F

10 11 12 13 14 15 16 17 18

19 1A 1B 1C 1D

00 00 00 00 00 00 00 00 00 00 00 00

Emergency memory address

Fixed data-1

(Initialized data) 1E 1F 20 21 22 23 24 25 26 27 28 29

2A 2B 2C 2D

2E 2F 30 31 32 33 34 35 36 37 38 39

3A 3B 3C 3D

3E 3F 40 41 42

47 80

80 65 80

03 25 24 11 05

AGC gain calibration adj.

AWB standard data input

Fixed data-1

(Initialized data)

Flange back adj.

Switching position adj.

28MHz origin osc. adj.

Fixed data-1

(Initialized data)

5-7

Page 90

Address

43 44 45 46 47 48

49 4A 4B 4C 4D

59 5A 5B 5C 5D

69 6A 6B 6C 6D

79 7A

Initial value

84 68 08

87 41 49

00 19 00 37 76 63

83 7A 8D 7A

33 C7 6B

40 9A

63 6B

Remark

Fixed data-1 (Initialized data)

HALL adj.

Max gain adj. Fixed data-1 (Initialized data)

Color reproduction adj. Fixed data-1 Color reproduction adj. Fixed data-1 (Initialized data)

Auto white balance adj.

IRIS IN/OUT adj.

Fixed data-1 (Initialized data) Flange back adj.

Angular velocity sensor sensitivity preset and steady shot check. CAP FG offset adj.

1.5MHz deviation adj.

1.7MHz deviation adj. BPF f0 adj. Fixed data-1 IR video deviation adj. IR audio deviation adj. IR video carrier freq. adj. Y OUT level adj. AFC f0 adj. C OUT level adj. Fixed data-1 Filter f0 adj. RP filter f0 adj. Fixed data-1 (Initialized data)

REC Y current adj.

Address

7B 7C 7D

7E 7F 80 81 82 83 84 85 86 87 88

89 8A 8B 8C 8D

99 9A 9B 9C 9D

9F A0 A1 A2 A3 A4 A5 A6 A7 A8 A9

AB AC

AE AF B0 B1 B2

Initial value

C0 C0 C0 C0 7C 7C 7C 7C

96 96 80

Remark

REC L level adj.

REC C current adj. Fixed data-1 (Initialized data)

Fixed data-2 Fixed data-1 (Initialized data)

5-8

Page 91

Address

B3 B4 B5 B6 B7 B8

B9 BA BB BC

BE BF

CB CC

CE CF D0 D1 D2 D3 D4 D5 D6 D7 D8 D9

DA DB DC DD

DE DF

E9 EA

Initial value

Remark

Fixed data-1 (Initialized data)

Fixed data-2 Fixed data-1 (Initialized data)

Address

EB EC ED EE

EF F0 F1 F2 F3 F4 F5 F6 F7 F8

F9 FA FB FC FD

Initial value

00 00 02

Remark

Fixed data-1 (Initialized data)

Fixed data-2 Fixed data-1 Flange back adj.

Color reproduction adj.

Fixed data-1 (Initialized data)

Table. 5-1-3.

5-9

Page 92

5. E Page Table

Note : Fixed data-1 : Initialized data. (Refer to “1. Initializing the D,E,F

Page Data”.) Fixed data-2 : Modified data. (Refer to “2. Modification of D, E, F Page Data”.)

Address

00 01

Initial value

Fixed data-1 (Initialized data)

Remark

02 03 04 05 06 07 08

09 0A 0B 0C 0D

19 1A 1B 1C 1D

29 2A 2B 2C 2D

Fixed data-2 (Modified data, copy the data built in

the same model.) 31 32

Fixed data-1

Fixed data-2

Address

33 34 35 36 37 38

39 3A 3B 3C 3D

49 4A 4B 4C 4D

59 5A 5B 5C 5D

69 6A

Initial value

Remark

Fixed data-1 (Initialized data)

Fixed data-2 Fixed data-1 (Initialized data)

Fixed data-2

5-10

Page 93

Address

6B 6C

6E 6F

70 71 72 73 74 75 76 77 78 79

7B 7C

7E 7F

80 81 82 83 84 85 86 87 88 89

8B 8C

8E 8F

90 91 92 93 94 95 96 97 98 99

9B 9C

9F A0 A1 A2

Initial value

Remark

Fixed data-2 Fixed data-1

Fixed data-2

Fixed data-1 (Initialized data)

Address

A3 A4 A5 A6 A7 A8 A9

AB AC

B0 B1 B2 B3 B4 B5 B6 B7 B8

B9 BA BB BC BD BE BF

C9 CA CB CC CD CE CF D0 D1 D2 D3 D4 D5 D6 D7 D8

Initial value

84 77 98

80 89 70

Remark

Fixed data-1 (Initialized data)

Fixed data-2 (Modified data, copy the data built in the same model.) Fixed data-1 (Initialized data)

VCO adj. (LCD) Fixed data-2 (Modified data, copy the data built in the same model.) Fixed data-1 (Initialized data)

Fixed data-2 Fixed data-1 (Initialized data) Bright adj. (LCD) Color adj. (LCD) White balance adj. (LCD)

Contrast adj. (LCD) D range adj. (LCD) V-COM level adj. (LCD) VCO adj. (LCD)

5-11

Page 94

Address

D9 DA DB DC DD

E0 E1 E2 E3 E4 E5 E6 E7 E8

E9 EA EB EC ED EE EF

F9 FA FB FC FD FE

Initial value

Remark

V-COM adj. (LCD) Fixed data-1 Color adj. (LCD) Fixed data-1 (Initialized data)

Fixed data-2 (Modified data, copy the data built in the same model.) Fixed data-1

Table. 5-1-4.

5-12

Page 95

1-3. CAMERA SYSTEM ADJUSTMENTS

Before perform the camera system adjustments, Check that the specified value of “28MHz Origin Oscillation Adjustment”, “Y OUT level Adjustment” and “C OUT level Adjustment” of “VIDEO SYSTEM ADJUSTMENT” are satisfied.

1. HALL Adjustment

For detecting the position of the lens iris, adjust the hall AMP gain and offset.

Subject Not required Measurement Point Display data of page 1 Measuring Instrument Adjustment remote commander Adjustment Page F Adjustment Address 47, 48 Specified Value 86 to 8A during IRIS OPEN

15 to 19 during IRIS CLOSE

Note : Displayed data of page 1 of the adjustment remote commander.

1 : 00 : XX

Display data

Adjusting method:

1) Select page: 0, address: 01, and set data: 01.

2) Select page: 6, address: 01, set data: 6D, and press the P AUSE button of the adjustment remote commander. (The HALL adjustment is performed and the adjustment data is stored in page: F, address: 47 and 48.)

3) Select page: 6, address: 02, and check that the data is “01”.

4) Select page: 6, address: 01, set data: 00, and press the PAUSE button.

Checking method:

1) Select page: 0, address: 03, and set data: 03.

2) Select page: 6, address: 01, set data: 01, and press the P AUSE button.

3) Select page: 1, and check that the display data (Note) during IRIS OPEN satisfies the specified value.

4) Select page: 6, address: 01, set data: 03, and press the P AUSE button.

5) Select page: 1, and check that the display data during IRIS CLOSE satisfies the specified value.

Processing after Completing Adjustments

1) Select page: 6, address: 01, set data: 00, and press the PAUSE button.

2) Select page: 0, address: 01, and set data: 00.

3) Select page: 0, address: 03, and set data: 00.

2. Flange Back Adjustment

The inner focus lens flange back adjustment is carried out automatically. In whiche v er case, the focus will be de viated during auto focusing/manual focusing.

2-1. Flange Back Adjustment(1)

Subject Flange back adjustment chart

(2.0 m from the front of the lens)

(Luminance: 350 ± 50 lux) Measurement Point Check operation on TV monitor Measuring Instrument Adjustment Page F Adjustment Address 38 to 3D, 5A to 5E, F8 to FA

Switch setting:

1) NIGHT SHOT..................................................................OFF

2) DIGITAL ZOOM (Menu display) ...................................OFF

3) STEADY SHOT (Menu display) .....................................OFF

4) VIDEO LIGHT (CCD-TRV66E).....................................OFF

Adjusting method:

1) Check that at both the zoom lens TELE end and WIDE end, the center of the chart for the flange back adjustment and center of the exposure screen coincide.

2) Select page: 0, address: 01, and set data: 01.

3) Check that the data of page: F, address:38 to 3D, 5A to 5E, F8 to FA is the initial value (See table below).

Address

39 3A 3B 3C 3D 5A

Data

03 25 24 11 05

Address

5B 5C

F8 F9

Data

00 19 10 37 00 00 02

4) Select page: 6, address: 02, and check that the data is “00”.

5) Select page: 6, address: 01, set data: 13, and press the P AUSE button of the adjustment remote commander.

6) Select page: 6, address: 01, set data: 15, and press the P AUSE button. (The adjustment data will be automatically input to page: F, addresses:38 to 3D, 5A to 5E, F8 to FA.)

7) Select page: 6, address: 02, and check that the data is “01”.

Processing after Completing Adjustments

1) Turn OFF the main power supply (8.4V).

2) Perform “Flange Back Adjustment (2)”.

5-13

Page 96

2-2. Flange Back Adjustment (2)

Perform this adjustment after performing “Flange Back Adjustment (1)”.

Subject Subject more than 500m away

(Subjects with clear contrast such as

buildings, etc.) Measurement Point Check operation on TV monitor Measuring Instrument Adjustment Page F Adjustment Address 38 to 3D, 5A to 5E, F8 to FA

Switch setting:

1) NIGHT SHOT..................................................................OFF

2) DIGITAL ZOOM (Menu display) ...................................OFF

3) STEADY SHOT (Menu display) .....................................OFF

4) VIDEO LIGHT (CCD-TRV66E) .....................................OFF

Adjusting method:

1) Set the zoom lens to the TELE end and expose a subject that is more than 500 m away (subject with clear contrast such as building, etc.). (Nearby subjects less than 500 m away should not be in the screen.)

2) Select page: 0, address: 01, and set data: 01.

3) Select page: 6, address: 02, and check that the data is “00”.

4) Select page: 6, address: 01, set data: 13, and press the PAUSE button of the adjustment remote commander.

5) Place a ND filter on the lens so that the optimum image is obtain.

6) Select page: 6, address: 01, set data: 29, and press the PAUSE button. (The adjustment data will be automatically input to page: F, addresses:38 to 3D, 5A to 5E, F8 to FA.)

7) Select page: 6, address: 02, and check that the data is “01”.

Processing after Completing Adjustments

1) Select page: 0, address: 01, and set data: 00.

2) Turn OFF the main power supply (8.4V).

3) Perform “Flange Back Check”.

3. Flange Back Check

Subject Siemens star

(2.0 m from the front of the lens)

(Luminance : approx. 200 lux) Measurement Point Check operation on TV monitor Measuring Instrument Specified Value Focused at the TELE end and WIDE end.

Switch setting:

1) NIGHT SHOT..................................................................OFF

2) DIGITAL ZOOM (Menu display) ...................................OFF

3) STEADY SHOT (Menu display) .....................................OFF

4) VIDEO LIGHT (CCD-TRV66E) .....................................OFF

Checking method:

1) Place the Siemens star 2.0m from the front of the lens.

2) To open the IRIS, decrease the luminous intensity to the Siemens star up to a point before noise appear on the image.

3) Shoot the Siemens star with the zoom TELE end.

4) Turn on the auto focus.

5) Check that the lens is focused (Note).

6) Select page: 6, address: 21, and set data: 10.

7) Shoot the Siemens star with the zoom WIDE end.

8) Observe the TV monitor and check that the lens is focused.

Note: When the auto focus is ON, the lens can be checked if it is

focused or not by observing the data on the page 1 of the adjustment remote commander.

1) Select page: 0, address: 03, and set data: 0F.

2) Page 1 shows the state of the focus. 1 : 00 : XX

Odd: Focused Even: Unfocused

Processing after Completing Adjustments

1) Select page: 6, address: 21, and set data: 00.

2) Select page: 0, address: 03, and set data: 00.

5-14

Page 97

4. Picture Frame Setting

Subject Color bar chart

(Color reproduction adjustment frame)

(1.5m from the front of the lens) Measurement Point Video output terminal Measuring Instrument Oscilloscope and TV monitor Specified Value A=B, C=D, E=F, t=0 ± 0.1msec

Switch setting:

1) NIGHT SHOT..................................................................OFF

2) DIGITAL ZOOM (Menu display) ...................................OFF

3) STEADY SHOT (Menu display) .....................................OFF

4) VIDEO LIGHT (CCD-TRV66E) .....................................OFF

Setting method:

1) Adjust the zoom and the camera direction, and set to the specified position.

2) Mark the position of the picture frame on the monitor display, and adjust the picture frame to this position in following adjustments using “Color reproduction adjustment frame”.

Check on the oscilloscope

1. Horizontal period

A=B

C=D

5. AGC Gain Calibration Adjustment

Subject Clear chart

(Color reproduction adjustment frame) Adjustment Page F Adjustment Address 2E, 2F, 30, 31

Switch setting:

1) NIGHT SHOT..................................................................OFF

2) DIGITAL ZOOM (Menu display) ...................................OFF

3) STEADY SHOT (Menu display) .....................................OFF

4) VIDEO LIGHT (CCD-TRV66E).....................................OFF

Adjusting method:

1) Select page: 0, address: 01, and set data: 01.

2) Select page: 6, address: 01, set data: 71, and press the P AUSE button of the adjusting remote commander. (When the adjustment data is take in, the data will be automatically input to page: F, address: 2E to 31.)

3) Select page: 6, address: 02, and check that the data is “01”.

Processing after Completing Adjustments

1) Select page: 6, address: 01, and set data: 00, and press the PAUSE button of the adjusting remote commander.

2) Select page: 0, address: 01, and set data: 00.

Fig. 5-1-6.

2. V ertical period

E=F

Fig. 5-1-7.

Check on the monitor TV (Underscanned mode)

Color bar chart picture frame

Monitor TV picture fram

Fig. 5-1-8.

5-15

Page 98

6. Color Reproduction Adjustment

Adjust the color Separation matrix coefficient so that proper color reproduction is produced.

Subject Color bar chart

(Color reproduction adjustment frame) Measurement Point Video output terminal Measuring Instrument Vectorscope Adjustment Page F Adjustment Address 4E, 50, FB, FC Specified Value All color luminance points should

settle within each color reproduction

frame.

Switch setting:

1) NIGHT SHOT..................................................................OFF

2) DIGITAL ZOOM (Menu display) ...................................OFF

3) STEADY SHOT (Menu display) .....................................OFF

4) VIDEO LIGHT (CCD-TRV66E) .....................................OFF

Adjusting method:

1) Select page: 0, address: 01, and set data: 01.

2) Select page: F , address: E1, set data: 1B, and press the PA USE button of the adjustment remote commander.

3) Select page: F, address: 27, set data: 3F, and press the PAUSE button.

4) Select page: 6, address: 01, set data: 3D, and press the P AUSE button.

5) Adjust the GAIN and PHASE of the vectorscope, and adjust the burst luminance point to the burst position of the color reproduction frame.

6) Change the data of page: F, address: 4E, 50, FB and FC, and settle each color luminance point in each color reproduction frame.

Note: Be sure to press the PAUSE button of the adjustment remote

commander before changing the addresses. If not, the new data will not be written to the memory.

Processing after Completing Adjustments

1) Select page: 6, address: 01, set data: 00, and press the PAUSE button of the adjustment remote commander.

2) Select page: F , address: E1, set data: 1E, and press the PAUSE button.

3) Select page: 0, address: 01, and set data: 00.

Burst position

7. IRIS IN/OUT Adjustment

For the unit to judge if the white balance is indoors or outdoors in auto white balance operations, measure the light level and write it in the EEPROM. If the level is not correct, the white balance will not be accurate.

Subject Clear chart

(Color reproduction adjustment frame) Measurement Point DDS display of LCD or TV monitor Measuring Instrument (Note) Adjustment Page F Adjustment Address 56, 57

Note: The right four digits of the DDS display data of LCD or TV monitor .

00 XX XX

Lower two digits Upper two digits

Switch setting:

1) NIGHT SHOT..................................................................OFF

2) DIGITAL ZOOM (Menu display) ...................................OFF

3) STEADY SHOT (Menu display) .....................................OFF

4) VIDEO LIGHT (CCD-TRV66E) .....................................OFF

Adjusting method:

1) Select page: 0, address: 01, and set data: 01.

2) Select page: 0, address: 03, and set data: 06.

3) Select page: D, address: 11, set data: 02, and press the P AUSE button of the adjustment remote commander.

4) Select page: 6, address: 01, set data: 0B, and press the P AUSE button.

5) Read the DDS display data (Note), and take the upper two digits as D1 and the lower two as D2.

6) Convert D1 to decimal notation, and obtain D1'. (Refer to Table 5-4-1. “Hexadecimal - decimal conversion table” of “5-4. Service Mode”.)

7) Calculate D3' using the following equations. (Equations 1 and 2 are for decimal notation calculation).

When D

2 D0

D3' = D1' – 21 Equation 1

When D2 < D0

D3' = D1' – 22 Equation 2

8) Convert D3' to hexadecimal notation, and obtain D3.

9) Select page: F, ad dress: 56, set data: D3, and press the PAUSE button.

10) Select page: 6, address: 01, set data: 09, and press the PAUSE button.

11) Read the DDS display data (Note), and take the upper two digits as D4 and the lower two as D5.

12) Conv ert D4 to decimal notation, and obtain D4'. (Refer to Table 5-4-1. “Hexadecimal - decimal conversion table” of “5-4. Service Mode”.)

13) Calculate D6' using the following equations. (Equations 3 and 4 are for decimal notation calculation).

When D5 F0

D6' = D4' – 13 Equation 3

When D5 < F0

D6' = D4' – 14 Equation 4

14) Convert D6' to hexadecimal notation, and obtain D6.

15) Select page: F, address: 57, set data: D6, and press the PAUSE button.

Fig. 5-1-9.

Processing after Completing Adjustments

1) Select page: D, address: 11, set data: 00, and press the P AUSE button of the adjustment remote commander.

2) Select page: 0, address: 01, and set data: 00.

3) Select page: 0, address: 03, and set data: 00.

4) Select page: 6, address: 01, set data: 00, and press the PAUSE button.

5-16

Page 99

8. MAX GAIN Adjustment

Setting the minimum illumination. If it is not consistent, the image level required for taking subjects in low illuminance will not be produced (dark).

Subject Clear chart

(Color reproduction adjustment frame) Measurement Point DDS display of LCD or TV monitor Measuring Instrument (Note) Adjustment Page F Adjustment Address 49 Specified Value C0 to FF

Note: The right two digits of the DDS display data is the object data.

00 00 XX

Object data

Switch setting:

1) NIGHT SHOT..................................................................OFF

2) DIGITAL ZOOM (Menu display) ...................................OFF

3) STEADY SHOT (Menu display) .....................................OFF

4) VIDEO LIGHT (CCD-TRV66E) .....................................OFF

Adjusting method:

1) Select page: 0, address: 01, and set data: 01.

2) Select page: D, address: 11, set data: 02, and press the P AUSE button of the adjustment remote commander.

3) Select of page: 0, address: 03, and set data: 01.

4) Select page: 6, address: 56, and set data: 40.

5) Select page: 6, address: 01, set data: 19, and press the PAUSE button of the adjustment remote commander.

6) Select page: F, address: 49, set da ta: 08, and press the PAUSE button.

7) Check that the DDS display data (Note) lies within the specified value.

9. Auto White Balance Standard Data Input

Subject Clear chart

(Color reproduction adjustment frame) Adjustment Page F Adjustment Address 32 to 35

Note 1: This adjustment should be carried out upon completion of “6. Color

Reproduction Adjustment”.

Note 2: Check that the data of page: 6, address: 02 is “00”. If not, select

page: 6, address: 01, set data: 00, and press the PAUSE button of the adjustment remote commander.

Switch setting:

1) NIGHT SHOT..................................................................OFF

2) DIGITAL ZOOM (Menu display) ...................................OFF

3) STEADY SHOT (Menu display) .....................................OFF

4) VIDEO LIGHT (CCD-TRV66E).....................................OFF

Adjusting method:

1) Select page: 0, address: 01, and set data: 01.

2) Wait for 2 seconds.

3) Select page: 6, address: 01, set data: 11, and press the P AUSE button of the adjustment remote commander.

4) Select page: 6, address: 01, set data: 0D, and press the P AUSE button. (When the standard data is take in, the data will be automatically input to page: F, address: 32 to 35.)

5) Select page: 6, address: 02, and check that the data is “01”.

6) Perform “Auto White Balance Adjustment”.

Processing after Completing Adjustments

1) Select page: 6, address: 01, set data: 00, and press the P AUSE button of the adjustment remote commander.

2) Select page: 0, address: 01, and set data: 00.

Processing after Completing Adjustments

1) Select page: D, address: 11, set data: 00, and press the P AUSE button of the adjustment remote commander.

2) Select page: 0, address: 01, and set data: 00.

3) Select page: 0, address: 03, and set data: 00.

4) Select page: 6, address: 01, set data: 00, and press the PAUSE button.

5) Select page: 6, address: 56, and set data: 00.

5-17

Page 100

10. Auto White Balance Adjustment

Adjust to the proper auto white balance output data. If it is not correct, auto white balance and color reproducibility will be poor.

Subject Clear chart

(Color reproduction adjustment frame)

Filter Filter C14 for color temperature

correction Measurement Point DDS display of LCD or TV monitor Measuring Instrument (Note 2) Adjustment Page F Adjustment Address 54, 55 Specified Value R ratio: 2B40 to 2BC0

B ratio: 5E40 to 5EC0

Note 1: Perform “Auto White Balance Standard Data Input” before this

Note 2: The right four digits of the DDS display data is the object data.

adjustment.

00 XXXX

Object data

Switch setting:

1) NIGHT SHOT..................................................................OFF

2) DIGITAL ZOOM (Menu display) ...................................OFF

3) STEADY SHOT (Menu display) .....................................OFF

4) VIDEO LIGHT (CCD-TRV66E) .....................................OFF

Adjusting method:

1) Place the C14 filter for color temperature correction on the lens.

2) Select page: 0, address: 01, and set data: 01.

3) Select page: D, address: 11, set data: 02, and press the P AUSE button of the adjustment remote commander.

4) Select page: 6, address: 01, set data: 3F , and press the PAUSE button.

5) Select page: 0, address: 03, and set data: 04.

6) Select page: F, address: 54, change the data, and adjust the average value of the DDS display data (Note 2) to the R ratio specified value.

7) Press the PAUSE button.

8) Select page: 0, address: 03, and set data: 05.

9) Select page: F, address: 55, change the data, and adjust the average value of the DDS display data (Note 2) to the B ratio specified value.

10) Press the PAUSE button.

Processing after Completing Adjustments

1) Select page: D, address: 11, set data: 00, and press the P AUSE button of the adjustment remote commander.

2) Select page: 0, address: 01, and set data: 00.

3) Select page: 0, address: 03, and set data: 00.

4) Select page: 6, address: 01, set data: 00, and press the PAUSE button.

5-18

Sony CCD-TRV77E, CCD-TRV66E Service Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Table for difference of function

Supplied accessories

TABLE OF CONTENTS

SERVICE NOTE

SELF-DIAGNOSIS FUNCTION

GENERAL

DISASSEMBLY

2-1. LCD UNIT, PD-105 BOARD

2-3. MECHANISM DECK

2-4. EVF BLOCK, VF-129 BOARD

2-6. MECHANISM DECK, VC-214, DD-117 BOARDS

2-7. VIDEO LIGHT (TRV66E)

2-8. CF-56 BOARD

2-9. HOW TO IDENTIFY DRUM AND NOTE

2-10.CIRCUIT BOARDS LOCATION

2-11.FLEXIBLE BOARDS LOCATION

3-1. OVERALL BLOCK DIAGRAM

BLOCK DIAGRAMS

3-2. CAMERA/VIDEO BLOCK DIAGRAM

3-3. VTR/CAMERA CONTROL BLOCK DIAGRAM

3-4. SERVO BLOCK DIAGRAM

3-5. MODE CONTROL BLOCK DIAGRAM

3-6. AUDIO BLOCK DIAGRAM

3-7. LCD BLOCK DIAGRAM

3-8. EVF BLOCK DIAGRAM

3-9. POWER BLOCK DIAGRAM

PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

4-1. FRAME SCHEMATIC DIAGRAM-1

FRAME SCHEMATIC DIAGRAM-2

4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

CD-209

VC-214

VL-23

MA-351

PD-105

VF-129

DD-117

CONTROL SWITCH BLOCK

ADJUSTMENTS

5-1. CAMERA SECTION ADJUSTMENT

1-1. PREPARATIONS BEFORE ADJUSTMENT (CAMERA SECTION)

1-2. INITIALIZATION OF D, E, F PAGE DATA

1-3. CAMERA SYSTEM ADJUSTMENTS