Sony BVM-F250, BVM-F170 Operation Manual

PROFESSIONAL VIDEO MONITOR

BVM-F250 BVM-F170

OPERATION MANUAL [English] 1st Edition (Revised 2)

English

Before operating the unit, please read this manual thoroughly and retain it for future reference.

For BVM-F250/F170

Important Safety Instructions

• Read these instructions.

• Keep these instructions.

• Heed all warnings.

• Follow all instructions.

• Do not use this apparatus near water.

• Clean only with dry cloth.

• Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.

• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

• Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

• Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

• Only use attachments/accessories specified by the manufacturer.

• Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

WARNING

To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

THIS APPARATUS MUST BE EARTHED.

For BVM-F250 only

This apparatus is provided with a main switch on the left side panel. Install this apparatus so that user can access the main switch easily.

For BVM-F170 only

WARNING

When installing the unit, incorporate a readily accessible disconnect device in the fixed wiring, or connect the power plug to an easily accessible socket-outlet near the unit. If a fault should occur during operation of the unit, operate the disconnect device to switch the power supply off, or disconnect the power plug.

For BVM-F250/F170

CAUTION

The apparatus shall not be exposed to dripping or splashing. No objects filled with liquids, such as vases, shall be placed on the apparatus.

CAUTION

The unit is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the unit itself has been turned off.

• Unplug this apparatus during lightning storms or when unused for long periods of time.

• Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

conforms to the safety regulations of each country if applicable.

2. Use the Power Cord (3-core mains lead) / Appliance Connector / Plug conforming to the proper ratings (Voltage, Ampere).

For the customers in the U.S.A.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

All interface cables used to connect peripherals must be shielded in order to comply with the limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

If you have questions on the use of the above Power Cord / Appliance Connector / Plug, please consult a qualified service personnel.

For the customers in Canada

This Class A digital apparatus complies with Canadian ICES-003.

For the customers in Europe

This product with the CE marking complies with the EMC Directive issued by the Commission of the European Community. Compliance with this directive implies conformity to the following European standards:

• EN55103-1 : Electromagnetic Interference (Emission)

• EN55103-2 : Electromagnetic Susceptibility (Immunity)

This product is intended for use in the following Electromagnetic Environment: E4 (controlled EMC environment, ex. TV studio).

The manufacturer of this product is Sony Corporation, 17-1 Konan, Minato-ku, Tokyo, 108-0075 Japan. The Authorized Representative for EMC and product safety is Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany. For any service or guarantee matters please refer to the addresses given in separate service or guarantee documents.

This apparatus shall not be used in the residential area.

WARNING: THIS WARNING IS APPLICABLE FOR USA ONLY. If used in USA, use the UL LISTED power cord specified below. DO NOT USE ANY OTHER POWER CORD.

Plug Cap Parallel blade with ground pin

(NEMA 5-15P Configuration) Cord Type SVT or SJT, three 16 or 18 AWG wires Length Minimum 1.5 m (4 ft .11in.), Less than 2.5 m

(8 ft .3 in.) Rating Minimum 10A, 125V

Using this unit at a voltage other than 120V may require the use of a different line cord or attachment plug, or both. To reduce the risk of fire or electric shock, refer servicing to qualified service personnel.

WARNING: THIS WARNING IS APPLICABLE FOR OTHER COUNTRIES.

1. Use the approved Power Cord (3-core mains lead) /

Appliance Connector / Plug with earthing-contacts that

For BVM-F170 only

Attention-when the product is installed in Rack:

Prevention against overloading of branch circuit

When this product is installed in a rack and is supplied power from an outlet on the rack, please make sure that the rack does not overload the supply circuit.

2.Providing protective earth

When this product is installed in a rack and is supplied power from an outlet on the rack, please confirm that the outlet is provided with a suitable protective earth connection.

3.Internal air ambient temperature of the rack

When this product is installed in a rack, please make sure that the internal air ambient temperature of the rack is within the specified limit of this product.

4.Prevention against achieving hazardous condition due to uneven mechanical loading

When this product is installed in a rack, please make sure that the rack does not achieve hazardous condition due to uneven mechanical loading.

5.Install the equipment while taking the operating temperature of the equipment into consideration

For the operating temperature of the equipment, refer to the specifications of the Operation Manual.

6.When performing the installation, keep the following space away from walls in order to obtain proper exhaust and radiation of heat.

Lower, Upper: 4.4 cm (1 Right, Left: 1.0 cm (

/4 inches) or more

/32 inches) or more

Installez l’appareil de sorte que l’utilisateur puisse facilement accéder à l’interrupteur principal.

Pour le BVM-F170 uniquement

AVERTISSEMENT

Lors de l’installation de l’appareil, incorporer un dispositif de coupure dans le câblage fixe ou brancher la fiche d’alimentation dans une prise murale facilement accessible proche de l’appareil. En cas de problème lors du fonctionnement de l’appareil, enclencher le dispositif de coupure d’alimentation ou débrancher la fiche d’alimentation.

Pour le BVM-F250/F170

For BVM-F250/F170

For the customers in Europe, Australia and New Zealand

WARNING

This is a Class A product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures.

For kundene i Norge

Dette utstyret kan kobles til et IT-strømfordelingssystem.

Apparatet må tilkoples jordet stikkontakt

Suomessa asuville asiakkaille

Laite on liitettävä suojamaadoituskoskettimilla varustettuun pistorasiaan

För kunderna i Sverige

Apparaten skall anslutas till jordat uttag

Français

Pour le BVM-F250/F170

AVERTISSEMENT

ATTENTION

Eviter d’exposer l’appareil à un égouttement ou à des éclaboussures. Ne placer aucun objet rempli de liquide, comme un vase, sur l’appareil.

ATTENTION

Cet appareil n’est pas déconnecté de la source d’alimentation secteur tant qu’il est raccordé à la prise murale, même si l’appareil lui-même a été mis hors tension.

Pour les clients au Canada

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Pour les clients en Europe

Ce produit portant la marque CE est conforme à la Directive sur la compatibilité électromagnétique (EMC) émise par la Commission de la Communauté européenne. La conformité à cette directive implique la conformité aux normes européennes suivantes:

• EN55103-1: Interférences électromagnétiques (émission)

• EN55103-2: Sensibilité électromagnétique (immunité)

Ce produit est prévu pour être utilisé dans l’environnement électromagnétique suivant: E4 (environnement EMC contrôlé, ex. studio de télévision).

Afin de réduire les risques d’incendie ou d’électrocution, ne pas exposer cet appareil à la pluie ou à l’humidité.

Afin d’écarter tout risque d’électrocution, garder le coffret fermé. Ne confier l’entretien de l’appareil qu’à un personnel qualifié.

CET APPAREIL DOIT ÊTRE RELIÉ À LA TERRE.

Pour le BVM-F250 uniquement

Cet appareil est doté d’un interrupteur principal sur son panneau gauche.

Le fabricant de ce produit est Sony Corporation, 1-7-1 Konan, Minato-ku, Tokyo, 108-0075 Japon. Le représentant autorisé pour EMC et la sécurité des produits est Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Allemagne. Pour toute question concernant le service ou la garantie, veuillez consulter les adresses indiquées dans les documents de service ou de garantie séparés.

Ne pas utiliser cet appareil dans une zone résidentielle.

AVERTISSEMENT

1. Utilisez un cordon d’alimentation (câble secteur à 3 fils)/fiche femelle/fiche mâle avec des contacts de mise à la terre conformes à la réglementation de sécurité locale applicable.

2. Utilisez un cordon d’alimentation (câble secteur à 3 fils)/fiche femelle/fiche mâle avec des caractéristiques nominales (tension, ampérage) appropriées.

Pour toute question sur l’utilisation du cordon d’alimentation/fiche femelle/fiche mâle ci-dessus, consultez un technicien du service après-vente qualifié.

Pour les clients en Europe, Australie et NouvelleZélande

AVERTISSEMENT

Il s’agit d’un produit de Classe A. Dans un environnement domestique, cet appareil peut provoquer des interférences radio, dans ce cas l’utilisateur peut être amené à prendre des mesures appropriées.

Beim BVM-F250/F170

VORSICHT

Das Gerät ist nicht tropf- und spritzwassergeschützt. Es dürfen keine mit Flüssigkeiten gefüllten Gegenstände, z. B. Vasen, darauf abgestellt werden.

VORSICHT

Solange das Netzkabel an eine Netzsteckdose angeschlossen ist, bleibt das Gerät auch im ausgeschalteten Zustand mit dem Strommetz verbunden.

Für Kunden in Europa

Dieses Produkt besitzt die CE-Kennzeichnung und erfüllt die EMV-Richtlinie der EG-Kommission. Angewandte Normen:

• EN55103-1: Elektromagnetische Verträglichkeit (Störaussendung)

• EN55103-2: Elektromagnetische Verträglichkeit (Störfestigkeit)

Für die folgende elektromagnetische Umgebung: E4 (kontrollierter EMV-Bereich, z.B. Fernsehstudio).

Deutsch

Beim BVM-F250/F170

WARNUNG

Um die Gefahr von Bränden oder elektrischen Schlägen zu verringern, darf dieses Gerät nicht Regen oder Feuchtigkeit ausgesetzt werden.

Um einen elektrischen Schlag zu vermeiden, darf das Gehäuse nicht geöffnet werden. Überlassen Sie Wartungsarbeiten stets nur qualifiziertem Fachpersonal.

DIESES GERÄT MUSS GEERDET WERDEN.

Nur beim BVM-F250

Dieses Gerät ist auf der linken Seite mit einem Hauptschalter versehen. Installieren Sie das Gerät so, dass der Benutzer leicht auf den Hauptschalter zugreifen kann.

Nur beim BVM-F170

WARNUNG

Beim Einbau des Geräts ist daher im Festkabel ein leicht zugänglicher Unterbrecher einzufügen, oder der Netzstecker muss mit einer in der Nähe des Geräts befindlichen, leicht zugänglichen Wandsteckdose verbunden werden. Wenn während des Betriebs eine Funktionsstörung auftritt, ist der Unterbrecher zu betätigen bzw. der Netzstecker abzuziehen, damit die Stromversorgung zum Gerät unterbrochen wird.

Der Hersteller dieses Produkts ist Sony Corporation, 1-7-1 Konan, Minato-ku, Tokyo, 108-0075 Japan. Der autorisierte Repräsentant für EMV und Produktsicherheit ist Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Deutschland. Bei jeglichen Angelegenheiten in Bezug auf Kundendienst oder Garantie wenden Sie sich bitte an die in den separaten Kundendienst- oder Garantiedokumenten aufgeführten Anschriften.

Dieser Apparat darf nicht im Wohnbereich verwendet werden.

WARNUNG

1. Verwenden Sie ein geprüftes Netzkabel (3-adriges

Stromkabel)/einen geprüften Geräteanschluss/einen geprüften Stecker mit Schutzkontakten entsprechend den Sicherheitsvorschriften, die im betreffenden Land gelten.

2. Verwenden Sie ein Netzkabel (3-adriges Stromkabel)/

einen Geräteanschluss/einen Stecker mit den geeigneten Anschlusswerten (Volt, Ampere).

Wenn Sie Fragen zur Verwendung von Netzkabel/ Geräteanschluss/Stecker haben, wenden Sie sich bitte an qualifiziertes Kundendienstpersonal.

Für Kunden in Europa, Australien und Neuseeland

WARNUNG

Dies ist eine Einrichtung, welche die Funk-Entstörung nach Klasse A besitzt. Diese Einrichtung kann im Wohnbereich Funkstörungen verursachen; in diesem Fall kann vom Betreiber verlangt werden, angemessene Maßnahmen durchzuführen und dafür aufzukommen.

Table of Contents

Chapter 1 Overview

Precautions........................................................ 8

On Safety..............................................................8

On Installation......................................................8

Handling the Screen .............................................8

On Burn-in ...........................................................8

On a Long Period of Use......................................9

Handling and Maintenance of the Screen ............9

On Dew Condensation .........................................9

On Repacking.......................................................9

Disposal of the Unit .............................................9

On Fan Error ........................................................9

Functions Supported in Software Version 1.1

and 1.2 ................................................ 10

Features............................................................ 11

Options ............................................................. 13

Input/Output Connectors and Input

Adaptors ............................................. 15

Location and Function of Parts

(BVM-F250)......................................... 16

Front Panel .........................................................16

Rear Panel/Left Side Panel.................................18

Location and Function of Parts

(BVM-F170)......................................... 20

Front Panel .........................................................20

Rear Panel ..........................................................22

Chapter 2 Preparations

Environments of the Installation Location.... 24

Input Adaptors................................................. 24

Installing an Input Adaptor (BVM-F250) ........ 25

Installing an Input Adaptor (BVM-F170) ........ 26

Attaching the Bracket (BVM-F250)................. 28

Mounting the Unit in a Rack (BVM-F170) ......28

Connections (BVM-F250)................................ 29

Connecting the Controller (BKM-16R) .............29

Connecting the Multiple Units with the

LAN ...................................................30

Connections (BVM-F170)................................ 31

Connecting the Controller (BKM-16R) .............31

Connecting the Multiple Units with the

LAN ...................................................32

Turning on the Power (BVM-F250).................33

Connecting the AC Power Cord.........................33

Turning on the Monitor......................................33

Turning on the Power (BVM-F170)..................34

Connecting to Power..........................................34

Turning on the Monitor......................................34

Settings .............................................................35

Selecting the Area ..............................................35

Setting for the LAN to Connect the Multiple

Units...................................................36

Selecting the Monitor (Designation of the Monitor

or Group ID Number) ........................37

Assigning the Input Signal to the Channel.........38

Setting the Display Mode of the Picture ............38

Adjusting...........................................................39

Chroma/Phase Adjustment.................................39

Color Temperature (White Balance)

Adjustment.........................................40

Brightness/Contrast Adjustment ........................40

Chapter 3 Menu

Basic Menu Operations ...................................42

Menu Operation Buttons....................................42

Displaying the Menu..........................................43

Setting or Adjusting in the Menu Operation ......43

Entering the Channel Number............................45

Aborting Menu Operation..................................45

Menu Structure.................................................46

Adjustment Menu .............................................52

Overview ............................................................52

Menu Function and Operation ...........................52

Channel Configuration Menu..........................57

Overview ............................................................57

Menu Function and Operation ...........................57

Auxiliary Setting Menu ....................................64

Overview ............................................................64

Menu Function and Operation ...........................64

Function Setting Menu ....................................65

Overview ............................................................65

Menu Function and Operation ...........................65

System Configuration Menu ...........................74

Overview ............................................................74

Menu Function and Operation ...........................74

File Management Menu....................................80

Overview ............................................................80

Menu Function and Operation ...........................80

System Status Menu ........................................82

Overview ............................................................82

Menu Function and Operation ...........................82

Controller Menu................................................84

Table of Contents

Overview............................................................84

Menu Function and Operation ...........................84

Key Protect Menu............................................. 89

Overview............................................................89

Menu Function and Operation ...........................89

Chapter 4 Operations

Selecting Display Mode...................................90

Setting the Display of Native Scan Mode ......91

Selecting the Native Scan/Scan Mode ...........92

Displaying Two Signals on One Screen

(Picture&Picture)................................93

Magnifying the Picture (Pixel Zoom)..............94

Capturing the Picture of the HD Signal

(HD Frame Capture) ...........................95

Displaying the Area Marker or Aspect

Marker .................................................96

Displaying the Audio Level Meter ..................97

Displaying the Time Code ...............................98

Switching the Display of the 3D Video

Signal ..................................................98

Copying the Setting or Adjustment Value to

Another Monitor ...............................100

Displaying the Monitor Status Page.............101

Assigning a Function to a Function

Button ............................................... 103

Assigning a Function to a Function Button ..... 103

Displaying the Assigned Functions

Collectively......................................103

Upgrading the Monitor and Controller.........104

Saving the Upgrade Data in a “Memory Stick

PRO”................................................104

Upgrading the Monitor ....................................105

Upgrading the Controller .................................105

Inserting/Ejecting the “Memory Stick”........ 134

Notes on “Memory Stick”................................134

Menu Index 136

Appendixes

Specifications (BVM-F250)............................107

Specifications (BVM-F170)............................109

Input Signals and Adjustable/Setting

Items..................................................112

Available Signal Systems..............................114

Available Signal Formats ..............................115

Aperture Modification Frequency.................121

Picture Display Size....................................... 122

Picture Frame Display ...................................124

Scan Mode Image...........................................126

Troubleshooting.............................................128

Dimensions (BVM-F250)................................130

Dimensions (BVM-F170)................................132

Using This Manual

This Operation Manual includes explanations for the BVM-F250 and BVM-F170. The model name is specified where there is a difference between the two models. (Example: Location and Function of Parts (BVM-F250)) Please note that the explanations are common to both models where no model name is specified.

Table of Contents

Chapter 1 Overview

Overview

Precautions

On Safety

• Operate the unit only with a power source as specified in the “Specifications” section.

• A nameplate indicating operating voltage, power consumption, etc., is located on the rear panel.

• Should any solid object or liquid fall into the cabinet, unplug the unit and have it checked by qualified personnel before operating it any further.

• Do not drop or place heavy objects on the power cord. If the power cord is damaged, turn off the power immediately. It is dangerous to use the unit with a damaged power cord.

• Unplug the unit from the wall outlet if it is not to be used for several days or more.

• Disconnect the power cord from the AC outlet by grasping the plug, not by pulling the cord.

• The socket-outlet shall be installed near the equipment and shall be easily accessible.

On Installation

Chapter

• Leave more than 40 cm of space in the rear of the unit to secure the operation area.

When the unit is installed on the desk or the like, leave at least 1U (4.4 cm) or more of space above and below the unit. Leaving 40 cm or more of space above the unit is recommended for service operation.

Handling the Screen

• The panel fitted to this unit is manufactured with high precision technology, giving a functioning pixel ratio of at least 99.99%. Thus a very small proportion of pixels may be “stuck”, either always off (black), always on (red, green, or blue), or flashing. In addition, over a long period of use, because of the physical characteristics of the panel, such “stuck” pixels may appear spontaneously. These problems are not a malfunction.

• Do not leave the screen facing the sun as it can damage the screen. Take care when you place the unit by a window.

• Do not push or scratch the monitor’s screen. Do not place a heavy object on the monitor’s screen. This may cause the screen to lose uniformity.

• The screen and the cabinet become warm during operation. This is not a malfunction.

• Allow adequate air circulation to prevent internal heat build-up. Do not place the unit on surfaces (rugs, blankets, etc.) or near materials (curtains, draperies) that may block the ventilation holes.

• Do not install the unit in a location near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, excessive dust, mechanical vibration or shock.

For BVM-F250 only

When installing the installation space must be secured in consideration of the ventilation and service operation.

• Do not block the ventilation slots, and vents of the fans.

• Leave a space around the unit for ventilation.

Precautions

On Burn-in

Due to the characteristics of the material used in the OLED panel for its high-precision images, permanent burn-in may occur if still images are displayed in the same position on the screen continuously, or repeatedly over extended periods.

Images that may cause burn-in

• Masked images with aspect ratios other than 16:9

• Color bars or images that remain static for a long time

• Character or message displays that indicate settings or the operating state

• On-screen displays such as center markers or area markers

To reduce the risk of burn-in

• Turn off the character and marker displays Press the MENU button to turn off the character displays. To turn off the character or marker displays of the connected equipment, operate the connected equipment accordingly. For details, refer to the operation manual of the connected equipment.

• Turn off the power when not in use Turn off the power if the viewfinder is not to be used for a prolonged period of time.

Screen saver

This product has a built-in screen saver function to reduce burn-in. When an almost still image is displayed for more than 10 minutes, the screen saver starts automatically and the brightness of the screen decreases.

On a Long Period of Use

Due to an OLED’s panel structure and characteristics of materials in its design, displaying static images for extended periods, or using the unit repeatedly in a high temperature/high humidity environments may cause image smearing, burn-in, areas of which brightness is permanently changed, lines, or a decrease in overall brightness.

• Wipe the screen surface gently with the supplied cleaning cloth or a soft dry cloth to remove dirt.

• Stubborn stains may be removed with the supplied cleaning cloth, or a soft cloth slightly dampened with a mild detergent solution.

• The screen may become scratched if the cleaning cloth is dusty.

• Never use strong solvents such as alcohol, benzene, thinner, acidic or alkaline detergent, detergent with abrasives, or chemical wipe as these may damage the screen.

• Use a blower to remove dust from the screen surface.

On Dew Condensation

If the viewfinder is moved suddenly from a cold place to a warm place, or used in a room with high humidity, water droplets may form on the interior of the product. This phenomenon is known as dew condensation. This product does not come with a feature that warns users of dew condensation. If water droplets are found on the casing, turn off the power, and wait until the condensation disappears before using.

On Repacking

Chapter 1 Overview

In particular, continued display of an image smaller than the monitor screen, such as in a different aspect ratio, may shorten the life of the unit. Avoid displaying a still image for an extended period, or using the unit repeatedly in a high temperature/high humidity environment such an airtight room, or around the outlet of an air conditioner.

To prevent any of the above issues, we recommend reducing brightness slightly, and to turn off the power whenever the unit is not in use.

Handling and Maintenance of the Screen

The surface of the screen is specially coated to reduce image reflection. Make sure to observe the following points as improper maintenance procedures may impair the screen’s performance. In addition, the screen is vulnerable to damage. Do not scratch or knock against it using a hard object.

• Be sure to disconnect the AC power cord from the AC outlet before performing maintenance.

• The surface of the screen is specially coated. Do not attach adhesive objects, such as stickers, on it.

• The surface of the screen is specially coated. Do not touch the screen directly.

Do not throw away the carton and packing materials. They make an ideal container which to transport the unit.

Disposal of the Unit

Do not dispose of the unit with general waste. Do not include the monitor with household waste. When you dispose of the monitor, you must obey the law in the relative area or country.

On Fan Error

The fan for cooling the unit is built in. When the fan stops and the OPERATE lamp flashes in red, the OVER RANGE lamp flashes in amber, and the ECO lamp lights in magenta on the front panel for fan error indication, turn off the power and contact an authorized Sony dealer.

If you have any questions about this unit, please contact your Sony service representative.

Precautions

Functions Supported in Software Version 1.1 and 1.2

The following new functions are supported for Version 1.1 and Version 1.2 of the BVM-F250/F170.

Chapter 1 Overview

Software Version 1.1

Menu Supported function Reference page

•Auto

(in the Color Temp Adj menu of the Adjustment menu)

•Copy From

(in the Picture Adj menu of the Adjustment menu) (in the Color Temp Adj menu of the Adjustment menu) (in the Channel Configuration menu) (in the Marker Setting menu of the Function Setting menu) (in the File Management menu)

•DisplayPort

(in the Format menu of the Channel Configuration menu) (in the RGB Range menu of the Channel Configuration menu)

• HDMI/DisplayPort Auto

(in the Matrix menu of the Channel Configuration menu) (in the RGB Range menu of the Channel Configuration menu)

• HDMI/DP Status

(in the System Status menu)

• Over Range

(in the On Screen Set menu of the System Configuration menu)

•Save To

(in the File Management menu)

• Delete

(in the File Management menu)

1) This function is equipped with BVM-F170 only.

2) Use the controller with software version 1.6 or higher to use this function.

Automatic color temperature adjustment can be performed using the built-in color sensor.

Data in this monitor, in another monitor or in a “Memory Stick” can be copied.

The settings for the DisplayPort signal are available. 58, 62

Matrix switching (Matrix) and quantization range setting (RGB Range) for the HDMI or DisplayPort signal are available.

The information of the HDMI and DisplayPort signals can be displayed.

The zebra pattern can be displayed on the portion of image that exceeds the allowable range of the internal signal processing circuit.

Stores the system data to a “Memory Stick”. 80

Deletes a file in the “Memory Stick”. 81

53, 55, 63, 67, 80

60, 62

Software Version 1.2

Menu Supported function Reference page

•ECO lamp

• DisplayPort Upgrade

(in the Monitor Upgrade menu of the System Configuration menu)

• ENTER button on the controller

3) Use the controller with software version 1.7 or higher to use this function.

Functions Supported in Software Version 1.1 and 1.2

Indicates the power consumption status of the monitor by the color of the lamp.

DisplayPort data can be upgraded. 79, 104

The functions assigned to the function buttons on the controller can be displayed collectively.

17, 21

42, 103

Features

The BVM-F250 is 25-inch Professional Video Monitor, and the BVM-F170 is 16.5-inch Professional Video Monitor. These are suitable for television stations or video production houses, where precise image reproduction is required.

The monitor features OLED panel and “TRIMASTER which is a new technology developed for three elements, “accurate color reproduction”, “precision imaging” and “quality picture consistency,” that are in demand for professional use. “TRIMASTER” decreases the viewing difference that occurs due to the individuality of each panel. Also, the monitor realizes the high picture quality and high-trust required for the master monitor by the color management system with its wide color gamut device, high-resolution/precise gradation display, highly accurate signal processing and panel correction function.

1) TRIMASTER is a trademark of Sony Corporation.

Advantages of OLED panel technology

The OLED panel makes use of an organic material, which emits light when an electric current is applied. Being selfemitting, the strength of luminescence can be controlled by the amount of electric current. This brings about the following three features:

Quick motion picture response: The luminescent state of the OLED panel can be changed instantaneously by changing the current flow in the organic material. This enables a quick motion picture response and production of images with minimal blurring and ghosting. Furthermore, performance for shooting on location is not influenced by changes in environmental temperature.

High contrast and wide dynamic range: The OLED panel does not emit light when black signal is applied to the monitor, enabling a pure black screen to be displayed. Furthermore, thanks to a wide dynamic range the panel impressively displays brilliance and clarity of various sparkling images, such as stars in a night sky twinkling, night illuminations winking or glass glittering, etc.

Rich color reproduction: An OLED panel’s self-luminescence also allows for great color reproduction across the entire spectrum in practically any shade or brightness.

Sony’s Super Top Emission

OLED panel

The 25-type (BVM-F250) or 16.5-type (BVM-F170) full HD (1920 × 1080) OLED panel features Sony’s Super Top Emission structure. Unlike the conventional bottom

”,

emission structure of TFT, Sony’s OLED panel can reproduce a crisper image due to high brightness. Furthermore, a unique microcavity structure makes RGB primary colors purer and deeper by utilizing light resonance effects that magnify optimum light wave lengths and diminish undesired light wave lengths. The panel’s 10-bit driver enables smooth gradation of color shading.

2) “Super Top Emission” is a trademark that represents the OLED technology of Sony Corporation.

12-bit precision display engine for professional use

The panel is equipped with a unique signal process engine developed for the professional use monitor. This engine incorporates 12-bit output accuracy at each process, and provides a high-quality I/P conversion algorithm, scaling processing, panel driving and a highly accurate color management system.

Multi color space

The Sony’s unique OLED panel with a wide color gamut and color management system which uses the unique 3D LUT (Look Up Table) reproduces the color space that complies with the broadcast standard ITU-R BT.709, EBU and SMPTE-C accurately. A wider color space

allows

digital cinema reproductions.

3) The RGB chromaticity of SMPTE RP 431-2 is not covered in full.

High-quality I/P conversion processing

A high-quality picture near the original one, in which jagged lines and conversion errors are decreased by detecting the feature of the picture inside the subdivided block and processing properly, is reproduced. The signal delay is decreased by judging the animation or still picture from the past video signal.

Interlace display mode

The interlace signal is displayed as the interlace picture by inserting the black line without I/P conversion processing. A picture faithful to the original signal and with the same feel as a CRT is gained.

For setting the display, see “Selecting Display Mode” on page 90.

Available to a multi signal format

The monitor supports various input signals such as 720 × 576/50i to 1920 × 1080/50P, 60P and variable computer signals up to 1920 × 1080. The 3G/HD/SD-SDI inputs,

HDMI

and DisplayPort5) (HDCP correspondence) inputs, and four option ports are equipped for the standard interface. If you install optional input adaptors, the monitor expands inputs of 3G-SDI, HD-SDI or SD-SDI, and supports Dual-link HD-SDI, RGB, YPbPr, Y/C, and composite signal inputs.

4) HDMI, the HDMI logo and High-Definition Multimedia Interface are

trademarks or registered trademarks of HDMI Licensing, LLC.

Chapter 1 Overview

Features

5) DisplayPort, DisplayPort logo and VESA are trademarks or registered trademarks of Video Electronics Standards Association.

HD frame capture function

The frame of the 3G/HD-SDI input signal is captured and

saved used to confirm the color tone and picture angle of the

Chapter 1 Overview

as a picture file in the “Memory Stick”. This is

current scene and recorded scene by using the multi display (Picture&Picture) function.

For the operation, see “Capturing the Picture of the HD Signal (HD Frame Capture)” on page 95.

6) As the frame of the input signal is captured, the data and marker set by the monitor is not reflected.

Aspect selectable function

A squeezed and recorded signal is displayed with the correct angle. You can select from 4:3 and 16:9 aspect modes.

Remote control function (Ethernet control)

The controller controls up to 32 monitors by the Ethernet (10BASE-T/100BASE-TX) connection. Up to four controllers are connected to one monitor in single mode. You can control individual monitors or monitor groups simply by entering the monitor ID number or group ID number. You can also execute the same operation on all connected monitors, or put all connected monitors into the same setup and adjustment state.

Multi display function

Two kinds of input signals are output on the monitor. Side by side mode is useful for adjusting the color or comparing two pictures.

For the operation, see “Displaying Two Signals on One Screen (Picture&Picture)” on page 93.

Pixel zoom function

As part of the picture is magnified up to 8 times without scaling processing, this is convenient for confirming a minute part of the signal.

For the operation, see “Magnifying the Picture (Pixel Zoom)” on page 94.

Safe area marker and aspect marker functions

The monitor is equipped with two area markers and center marker as the safe area marker and aspect marker for confirming the picture angle.

For the operation, see “Displaying the Area Marker or Aspect Marker” on page 96.

Scan selection/Native scan display function

You can select from under scan (–3%), normal scan (0%) and over scan (mask of the 5% over scan portion in the normal scan) for the picture display. The monitor is equipped with a native scan display function which maps the pixel of the signal to the panel in one-to-one mode. You can select the mode from ×1, ×2 or Aspect Correction to display a signal in native mode. An SD signal of non-square pixels (the number of H pixels of the signal system is 720 or 1440) or a 640 × 480 SD signal of HDMI/DisplayPort video is displayed correctly by scaling processing of doubling for the V direction and correct aspect ratio for the H direction, and the picture is also optimized and displayed by modifying the aperture coefficient value, filter coefficient value, etc. in Aspect Correction mode.

For the operation, see “Selecting the Native Scan/Scan Mode” on page 92.

Time code display function

The time code superimposed on the SDI signal is displayed.

Closed caption display function

EIA/CEA-608 or EIA/CEA-708 standard closed caption signals superimposed on the SDI signals are displayed by installing the optional input adaptor (BKM-244CC).

Audio level meter display function

The audio level of the embedded audio signals superimposed on the SDI signal is displayed by installing the optional input adaptor (BKM-250TG).

3D signal analyzing function

The monitor supports the following display modes of the 3D signal analyzing function if you install the optional input adaptor (BKM-250TG). For this function, twodimensional (2D) view is used. The signals are not displayed in stereoscopic view. The available display modes differ depending on the serial number of the BKM-250TG.

For the operation, see “Switching the Display of the 3D Video Signal” on page 98.

Difference display (with serial number 7300001 or higher): The difference between the luminance signal of the left (L) 3D video signal and that of the right (R) signal is displayed. This display is useful for checking parallax amount.

Checkerboard display (with serial number 7100001 or higher): The left (L) and right (R) 3D video signals are displayed in a checkerboard pattern on the screen. This display is useful for comparing the luminance or color settings of neighboring L and R images.

L/R switching display (with serial number 7100001 or higher): The dual-stream left (L) and right (R) 3D video signals are alternately displayed on the screen. This display is useful for comparing the color or brightness of the L and R

Features

signals, as a black frame is not inserted when the two signals are switched.

Horopter check display (with serial number 7100001 or higher): Either left (L) or right (R) 3D video signals, or both L and R signals are displayed in monochrome mode. This display is useful for checking a subtle depth of a subject located in the boundary plane of the screen, that is, whether it is near or far from the screen surface.

Horizontal flip display (with serial number 7100001 or higher): The input 3D video signals whose left (L) or right (R) signal has been inverted horizontally by a half-mirror type 3D rig are displayed as non-inverted images.

Note

The horizontal flip display function of this monitor inverts the input signals to display them. Since the internal sync is applied to any signal delayed by the inversion, there is a time lag between input and the displayed image.

Screen saver

When a nearly still image is displayed continuously for 10 minutes or more, the screen saver starts automatically to reduce the brightness of the screen to prevent burn-in.

Variable picture adjustment functions

Auto chroma, phase and matrix adjustment functions are equipped.

Other features

• The color temperature is selectable from D65, D93 and User.

• Built-in test pattern for 100% white signal, 20% gray signal, 0% black signal, PLUGE (Picture Line Up Generation Equipment) signal, color-bar signal, 5 step gray scale signal and ramp signal.

• Chroma Up function that increases the chroma setting by 12 dB.

• Blue only function and RGB cut off function to monitor signal noise.

• A parallel remote of the contact point control connector is equipped.

Options

For external control

Chapter 1 Overview

BKM-16R Monitor Control Unit

The BKM-16R is a controller of the BVM-F250/F170 and you can control multiple monitors from one controller.

In this manual, the BKM-16R is referred to as the controller.

For installation

BKM-37H/BKM-38H Controller Attachment Stand (for BVM-F250 only)

Used to join a BKM-16R and the BVM-F250. Using the BKM-37H, you can adjust the monitor angle up or down.

BKM-39H Controller Attachment Stand (for BVM-F170 only)

Used to join a BKM-16R and the BVM-F170.

SMF-700 Monitor Interface Cable

Used to connect the BVM-F250/F170 to the BKM-16R.

Input adaptors

The input connector panel is composed by installing the optional input adaptor into the input option port on the monitor. Up to four adaptors can be installed to the monitor. The input signal type for each connector of the adaptor is set with the Channel Configuration menu, in accordance with the configuration of the connector panel.

Note

When installing the adaptor, be sure to perform the necessary input signal setup with the Channel Configuration menu. If the setup is not performed, the adaptors may not function correctly.

For information about the Channel Configuration menu, see page 57.

For details of each input adaptor, refer to the operating instructions of each model.

BKM-220D SDI 4:2:2 Input Adaptor

Includes a decoder for serial digital signals (525/625 component). Input/output connectors for two serial digital channels and output connector for one monitor channel are equipped.

Options

BKM-227W NTSC/PAL Input Adaptor

Includes a decoder for NTSC/PAL/PAL-M/SECAM signals. Input/output connectors for each one composite signal channel and Y/C signal channel are equipped.

BKM-229X Analog Component Input Adaptor

Chapter 1 Overview

Includes a decoder for analog component signals and analog RGB signals. Input connector for one channel is equipped.

BKM-243HS HD/D1-SDI Input Adaptor

Includes a decoder for serial digital component signals. Input/output connectors for two serial digital channels and output connector for one monitor channel are equipped.

BKM-244CC HD/SD-SDI Closed Caption Adaptor

Includes a decoder for serial digital component signals. EIA/CEA-608 or EIA/CEA-708 standard closed caption signals superimposed on the SDI signals are decoded and displayed. Input/output connectors for two serial digital channels and output connector for one monitor channel are equipped.

BKM-250TG 3G/HD/SD-SDI Input Adaptor

Includes a decoder for serial digital component signals. Time code and audio level of the embedded audio signals superimposed on the SDI signals are displayed. 3D signal analyzing function is also supported. Input/output connectors for two serial digital channels and output connector for two monitor channels are equipped.

Notes

• The signal from the MONITOR OUT connector of the BKM-220D, BKM-243HS, BKM-244C and BKM250TG does not satisfy the ON-LINE signal specifications.

• An input adaptor with a specified serial number may be required for your intended use. For the serial numbers of the input adaptors available for this unit, see “Input Adaptors” (page 24).

Options

Input/Output Connectors and Input Adaptors

This monitor is equipped with two 3G/HD/SD-SDI input connectors, an HDMI input connector, and a DisplayPort input connector for the standard interface. In this manual, these connectors are referred to as the standard input. By adding the optional input expansion adaptors, the input/output connector panel can be assembled in a wide variety of configurations. The signals that each connector supports are given in the following table. The type of signal to be applied to each input/ output connector is set with the Channel Configuration menu (page 57) .

List of input/output connectors and input adaptors

Input signal Standard

input

Serial digital input

Analog input Composite NTSC a

HDMI Video a

DisplayPort Video a

Number of digital inputs 2 2 – – 2 2

Number of analog inputs – – 1 1 – –

Number of HDMI inputs 1 – – – – –

Number of DisplayPort input 1 – – – – –

Single-link SD-SDI Component 525/625

Single-link HD-SDI aaa Dual-link HD-SDI a (2) a Single-link 3G-SDI aa

Composite PAL a Composite PAL-M a Composite SECAM a Y/C NTSC a Y/C PAL a Y/C PAL-M a Y/C SECAM a YPbPr 525i/625i a RGB 525i/625i a YPbPr/RGB 1080/24PsF a YPbPr/RGB 1080/24P a

YPbPr/RGB 1080/50i (25PsF)

YPbPr/RGB 1080/25P a

YPbPr/RGB 1080/60i (30PsF)

YPbPr/RGB 1080/30P a YPbPr/RGB 720/50P a YPbPr/RGB 720/60P a

Computer a

aa aa

BKM-220D BKM-227W BKM-229X BKM-

a: Signal can be reproduced. a(2): Two adaptors are used.

Input adaptor

243HS/ 244CC

BKM250TG

Chapter 1 Overview

For details, see “Available Signal Formats” on page 115.

Input/Output Connectors and Input Adaptors

Location and Function of Parts (BVM-F250)

Front Panel

Chapter 1 Overview

1 Tally lamp

2 OPERATE lamp

3 OVER RANGE lamp

a Tally lamp

With factory settings, the tally lamp lights when pins No. 8 and No. 9 of the PARALLEL REMOTE connector on the left side panel are shorted. By changing the setting in the Parallel Remote menu (page 75) of the System Configuration menu, different pins on the PARALLEL REMOTE connector can be used to control the tally lamp.

b OPERATE lamp

When the MAIN POWER switch (on the left side panel) is turned on, internal data initialization starts and the OPERATE lamp flashes in red for a while. When the signal is output, the lamp flashes in green to indicate that data initialization continues. When initialization is finished and the monitor enters its operation mode, the lamp lights in green. The OPERATE lamp is lit in red when the monitor is in standby mode. The monitor will be in standby mode under the following conditions:

• Standby Mode is set to On in the Power menu (page 76) of the System Configuration menu and the MAIN POWER switch (on the left side panel) is turned on. (The OPERATE lamp will flash for initialization after the switch is turned on, then will light.)

• The monitor is changed from operation mode to standby mode by external control.

4 ECO lamp

Lights in green when the monitor is put into operation mode from standby mode by pressing the MONITOR I/1 switch of the controller.

Notes

• When the OPERATE lamp is flashing in red, the monitor cannot be put into operation mode. Wait until the lamp is steadily lit.

• When the OPERATE lamp is flashing in green, the monitor is not in full operation mode and images cannot be displayed correctly. Wait until the lamp is steadily lit in green.

The OPERATE lamp may indicate an error or warning. For details, see “Error/warning display by the lamp” (page 17).

c OVER RANGE lamp

Lights in amber when ABL (Automatic Brightness Limiter) starts. Also lights in amber when the signal level has exceeded the dynamic range of the signal processing circuit. Decrease the contrast or brightness when the OVER RANGE lamp is lit.

Location and Function of Parts (BVM-F250)

The OVER RANGE lamp may indicate an error or warning. For details, see “Error/warning display by the lamp” (page 17).

d ECO lamp

The color of the lamp changes according to the power consumption status of the monitor. The color changes from green to yellow to magenta in order of greater power consumption. Decreasing the luminance of the screen by adjusting brightness/contrast is recommended when the lamp lights in yellow or magenta. The lamp starts flashing rapidly approximately one minute before the screen saver is activated. Flashing slows in green when the screen saver starts.

The ECO lamp may indicate an error or warning. For details, see “Error/warning display by the lamp” (page 17).

Error/warning display by the lamp

The OVER RANGE lamp, OPERATE lamp and/or ECO lamp on the front panel may show an error or warning while the monitor is being operated.

Chapter 1 Overview

If the error or warning is shown, please contact your Sony representative.

Error display

ECO lamp

Lights in yellow

Flashes in yellow

Lights in magenta

Flashes in magenta

OVER RANGE lamp

Lights in amber

Flashes in amber

Lights in amber

Flashes in amber

Lights in amber

OPERATE lamp

Flashes in red

Symptoms

The power in the panel part is unusual.

The temperature in the panel part is unusual.

The ambient temperature sensor is unusual.

Fan error.

Device error.

Warning display

ECO lamp

–: Status except for error display.

–

OVER RANGE lamp

Flashes in amber

Lights in amber

OPERATE lamp

–

Symptoms

The luminance is reduced to protect the panel from an increase of temperature in the panel part.

Over range

Location and Function of Parts (BVM-F250)

Rear Panel/Left Side Panel

Chapter 1 Overview

Handles

1 DC 5V OUT connector

2 LAN (10/100) connector 3 NETWORK switch

4 PARALLEL REMOTE connector

6 3G/HD/SD-SDI input 2 connector

5 STANDARD PORT

6 HDMI input connector

7 DisplayPort input connector

8 Input option ports

9 AC IN connector q; MAIN POWER switch

a DC 5V OUT connector (female)

Supplies the DC power to the controller. Connect to the DC 5V/12V IN connector of the controller with the SMF-700 or the cable supplied with the BKM37H/38H.

CAUTION

DC 5V OUT connector (female) is non LPS (Limited Power Source) circuit.

b LAN (10/100) connector (10BASE-T/100BASE-TX)

Connect to the LAN (10/100) connector of the controller by using the SMF-700 or the cable supplied with the BKM37H/38H. Or connect to the network or the LAN (10/100) connector of the controller by using a 10BASE-T/ 100BASE-TX LAN cable (shielded-type, optional).

CAUTION

• For safety, do not connect the connector for peripheral device wiring that might have excessive voltage to this port. Follow the instructions for this port.

Location and Function of Parts (BVM-F250)

• When you connect the LAN cable of the unit to peripheral device, use a shielded-type cable to prevent malfunction due to radiation noise.

• The connection speed may be affected by the network system.

ATTENTION

Par mesure de sécurité, ne raccordez pas le connecteur pour le câblage de périphériques pouvant avoir une tension excessive à ce port. Suivez les instructions pour ce port.

VORSICHT

Aus Sicherheitsgründen nicht mit einem PeripheriegerätAnschluss verbinden, der zu starke Spannung für diese Buchse haben könnte. Folgen Sie den Anweisungen für diese Buchse.

c NETWORK switch LAN: To connect to the network. PEER TO PEER: To connect to the LAN (10/100)

connector of the controller in 1 to 1 connection.

d PARALLEL REMOTE connector (D-sub 9-pin,

female)

Forms a parallel switch and controls the monitor externally. The pin assignment and factory setting function assigned to each pin are given below.

MONITOR OUT connector

This is the MONITOR OUT connector for SDI INPUT 1 or SDI INPUT 2 connector.

Note

The signal from this MONITOR OUT connector does not satisfy the ON-LINE signal specifications.

f HDMI input connector

Inputs the HDMI signal. HDMI (High-Definition Multimedia Interface) is an interface that supports both video and audio on a single digital connection, allowing you to display high quality digital picture. The HDMI specification supports HDCP (High-bandwidth Digital Content Protection), a copy protection technology that incorporates coding technology for digital video signals.

Chapter 1 Overview

Pin number Function

1 Sets input signal channel 1 (numeric

keypad function).

2 Sets input signal channel 2 (numeric

keypad function).

3 Selects sync signal (SYNC button

function).

4 Selects whether monochrome image is

displayed or the monitor switches the display mode automatically between color image and monochrome image depending on the input signal (MONO button function).

5 Marker (set in the Marker Setting

menu) On/Off (MARKER button function).

6, 7 Not connected

8 Tally lamp On/Off

9Ground

All pin function assignments can be changed with the Parallel Remote menu (page 75) of the System Configuration menu.

To switch each function between On and Off or between enable and disable, change pin connections in the following way.

On or enabled: Short each pin and pin 9 together. Off or disabled: Leave each pin open.

e STANDARD PORT SDI INPUT 1 connector

Inputs serial digital signals (standard SDI input 1).

SDI INPUT 2 connector

Inputs serial digital signals (standard SDI input 2).

Notes

• The HDMI audio signal is not available for this monitor.

• Use HDMI compliant cable (optional), Category 2 (High Speed HDMI Cable), with HDMI logo.

g DisplayPort input connector

Inputs the DisplayPort signal. DisplayPort is an interface developed by VESA that supports transfer of both video and audio digital signals on a single cable. It also supports HDCP, a copy protection technology that incorporates coding technology for digital video signals.

Note

This monitor does not support DisplayPort audio signals.

h Input option ports

Used to install the optional input adaptors.

For installing the input adaptor, see page 25.

For the input signals, see “Input/Output Connectors and Input Adaptors” on page 15.

i AC IN connector (3-pin)

Connects the monitor to an AC power source, via the supplied AC power cord.

j MAIN POWER switch

When turned on (?), the monitor enters operation mode. By setting in the Power menu (page 76) of the System Configuration menu, the monitor can also be set to enter standby mode when the MAIN POWER switch is turned on.

Location and Function of Parts (BVM-F250)

Location and Function of Parts (BVM-F170)

Front Panel

Chapter 1 Overview

1 Tally lamp

2 OPERATE lamp

3 OVER RANGE lamp

a Tally lamp

With factory settings, the tally lamp lights when pins No. 8 and No. 9 of the PARALLEL REMOTE connector on the rear panel are shorted. By changing the setting in the Parallel Remote menu (page 75) of the System Configuration menu, different pins on the PARALLEL REMOTE connector can be used to control the tally lamp.

b OPERATE lamp

When the MAIN POWER switch (on the rear panel) is turned on, internal data initialization starts and the OPERATE lamp flashes in red for a while. When the signal is output, the lamp flashes in green to indicate that data initialization continues. When initialization is finished and the monitor enters its operation mode, the lamp lights in green. The OPERATE lamp is lit in red when the monitor is in standby mode. The monitor will be in standby mode under the following conditions:

• Standby Mode is set to On in the Power menu (page 76) of the System Configuration menu and the MAIN POWER switch (on the rear panel) is turned on. (The OPERATE lamp will flash for initialization after the switch is turned on, then will light.)

• The monitor is changed from operation mode to standby mode by external control.

4 ECO lamp

Lights in green when the monitor is put into operation mode from standby mode by pressing the MONITOR I/1 switch of the controller.

Notes

• When the OPERATE lamp is flashing in red, the monitor cannot be put into operation mode. Wait until the lamp is steadily lit.

• When the OPERATE lamp is flashing in green, the monitor is not in full operation mode and images cannot be displayed correctly. Wait until the lamp is steadily lit in green.

The OPERATE lamp may indicate an error or warning. For details, see “Error/warning display by the lamp” (page 21).

c OVER RANGE lamp

Location and Function of Parts (BVM-F170)

The OVER RANGE lamp may indicate an error or warning. For details, see “Error/warning display by the lamp” (page 21).

d ECO lamp

The ECO lamp may indicate an error or warning. For details, see “Error/warning display by the lamp” (page 21).

Error/warning display by the lamp

The OVER RANGE lamp, OPERATE lamp and/or ECO lamp on the front panel may show an error or warning while the monitor is being operated.

Chapter 1 Overview

If the error or warning is shown, please contact your Sony representative.

Error display

ECO lamp

Lights in yellow

Flashes in yellow

Lights in magenta

Flashes in magenta

OVER RANGE lamp

Lights in amber

Flashes in amber

Lights in amber

Flashes in amber

Lights in amber

OPERATE lamp

Flashes in red

Symptoms

The power in the panel part is unusual.

The temperature in the panel part is unusual.

The ambient temperature sensor is unusual.

Fan error.

Device error.

Warning display

ECO lamp

–: Status except for error display.

–

OVER RANGE lamp

Flashes in amber

Lights in amber

OPERATE lamp

–

Symptoms

The luminance is reduced to protect the panel from an increase of temperature in the panel part.

Over range

Location and Function of Parts (BVM-F170)

Rear Panel

4 DC 5V OUT connector

Chapter 1 Overview

Handle

1 MAIN POWER switch

2 DC IN 24 V - 28 V

connector

3 AC IN connector

a MAIN POWER switch

When turned on, the monitor enters operation mode. By setting in the Power menu (page 76) of the System Configuration menu, the monitor can also be set to enter standby mode when the MAIN POWER switch is turned on.

b DC IN 24 V - 28 V (DC power input) connector

(XLR 3-pin, male)

Connect the 24 V to 28 V DC power supply.

21 3

5 LAN (10/100) connector

Handle

6 NETWORK switch

7 PARALLEL REMOTE

connector

8 STANDARD PORT

9 HDMI IN connector

q; DisplayPort input connector

qa Input option ports

e LAN (10/100) connector (10BASE-T/100BASE-TX)

Connect to the LAN (10/100) connector of the controller by using the SMF-700 or the cable supplied with the BKM39H. Or connect to the network or the LAN (10/100) connector of the controller by using a 10BASE-T/ 100BASE-TX LAN cable (shielded-type, optional).

CAUTION

• For safety, do not connect the connector for peripheral device wiring that might have excessive voltage to this port. Follow the instructions for this port.

• When you connect the LAN cable of the unit to peripheral device, use a shielded-type cable to prevent malfunction due to radiation noise.

• The connection speed may be affected by the network system.

Pin number Function

1 – (GND)

2 + (24 V to 28 V DC)

3NC

c AC IN connector (3-pin)

Connects the monitor to an AC power source, via the supplied AC power cord.

d DC 5V OUT connector (female)

Supplies the DC power to the controller. Connect to the DC 5V/12V IN connector of the controller with the SMF-700 or the cable supplied with the BKM39H.

CAUTION

DC 5V OUT connector (female) is non LPS (Limited Power Source) circuit.

Location and Function of Parts (BVM-F170)

ATTENTION

Par mesure de sécurité, ne raccordez pas le connecteur pour le câblage de périphériques pouvant avoir une tension excessive à ce port. Suivez les instructions pour ce port.

VORSICHT

Aus Sicherheitsgründen nicht mit einem PeripheriegerätAnschluss verbinden, der zu starke Spannung für diese Buchse haben könnte. Folgen Sie den Anweisungen für diese Buchse.

f NETWORK switch LAN: To connect to the network. PEER TO PEER: To connect to the LAN (10/100)

connector of the controller in 1 to 1 connection.

g PARALLEL REMOTE connector (D-sub 9-pin,

female)

Forms a parallel switch and controls the monitor externally. The pin assignment and factory setting function assigned to each pin are given below.

i HDMI IN connector

Chapter 1 Overview

Pin number Function

1 Sets input signal channel 1 (numeric

keypad function).

2 Sets input signal channel 2 (numeric

keypad function).

3 Selects sync signal (SYNC button

function).

4 Selects whether monochrome image is

displayed or the monitor switches the display mode automatically between color image and monochrome image depending on the input signal (MONO button function).

5 Marker (set in the Marker Setting menu)

On/Off (MARKER button function).

6, 7 Not connected

8 Tally lamp On/Off

9 Ground

All pin function assignments can be changed with the Parallel Remote menu (page 75) of the System Configuration menu.

Notes

• The HDMI audio signal is not available for this monitor.

• Use HDMI compliant cable (optional), Category 2 (High Speed HDMI Cable), with HDMI logo.

j DisplayPort input connector

Note

This monitor does not support DisplayPort audio signals.

k Input option ports

Used to install the optional input adaptors.

For installing the input adaptor, see page 26.

For the input signals, see “Input/Output Connectors and Input Adaptors” on page 15.

To switch each function between On and Off or between enable and disable, change pin connections in the following way.

On or enabled: Short each pin and pin 9 together. Off or disabled: Leave each pin open.

h STANDARD PORT SDI INPUT 1 connector

Inputs serial digital signals (standard SDI input 1).

SDI INPUT 2 connector

Inputs serial digital signals (standard SDI input 2).

MONITOR OUT connector

This is the MONITOR OUT connector for SDI INPUT 1 or SDI INPUT 2 connector.

Note

The signal from this MONITOR OUT connector does not satisfy the ON-LINE signal specifications.

Location and Function of Parts (BVM-F170)

Preparations

Chapter 2 Preparations

Chapter

Environments of the Installation Location

Illumination environments

The apparent color reproduction on the monitor is greatly affected by ambient light or glare.

Viewing angle

The ideal viewing angle is within 5 degrees (up/down/left/ right) off the center of the monitor screen when the operator views the entire monitor screen. Keep the viewing angle within 15 degrees off the center of the monitor screen.

Input Adaptors

Each input adaptor can be installed in any input option port on the monitor.

Caution

When you install the following input adaptors to this equipment, use those with the serial numbers given below.

• BKM-220D with serial number 2100001 or higher This equipment may not meet the requirements of the electromagnetic interference standard if designated input adaptors are not installed.

• BKM-227W with serial number 2100001 or higher This equipment may not work correctly or you may not be satisfied with their performance if designated input adaptors are not installed.

• BKM-229X with serial number 2200001 or higher This equipment may not work correctly or you may not be satisfied with their performance if designated input adaptors are not installed.

• BKM-243HS with serial number 2108355 or higher This equipment may not meet the requirements of the electromagnetic interference standard or work correctly, or you may not be satisfied with the performance if designated input adaptors are not installed.

• BKM-250TG with serial number 7300001 or higher To enable all five display modes of the 3D signal analyzing function, use the input adaptor with serial number 7300001 or higher.

Environments of the Installation Location / Input Adaptors

Caution

To reduce the risk of electric shock, turn off the MAIN POWER switch of the monitor and disconnect the AC power cord before installing or removing adaptors.

Installing an Input Adaptor (BVM-F250)

Loosen two screws and remove the cover of an input option port on the side panel of the monitor.

Cover of an input option port

Make sure the MAIN POWER switch is turned off, and disconnect the AC power cord.

Off

Insert the adaptor facing the board as shown below.

Chapter 2 Preparations

For connecting Dual-link HD-SDI signals

Two BKM-243HS or BKM-244CC input adaptors or one BKM-250TG input adaptor is required. When the BKM243HS or BKM-244CC adaptors are used, install the input adaptors in OPTION 1 and 2 option ports, or OPTION 3 and 4 option ports. The BKM-243HS or BKM-244CC cannot be used with the BKM-250TG for Dual-link operation.

To connect the cable

When the BKM-243HS or BKM-244CC adaptors are used, install the Link A signal to OPTION 1 or 3, and the

Link B signal to OPTION 2 or 4. Connect the cable to the same input number (both INPUT 1 or both INPUT 2) of the input adaptors installed in OPTION 1 and 2 option ports, or OPTION 3 and 4 option ports.

Board

Push the adaptor in until it is firmly fit into the connector inside the monitor, then tighten the two screws to secure the adaptor.

Example of Dual-link cable connection

OPTION 1 and 2

OPTION 3 and 4

Installing an Input Adaptor (BVM-F250)

INPUT 1

INPUT 2

INPUT 1

INPUT 2

When the BKM-250TG is used, install the Link A signal to INPUT 1, and the Link B signal to INPUT 2.

Installing an Input Adaptor (BVM-F170)

INPUT 1

Chapter 2 Preparations

INPUT 2

For 3D signal analyzing function

Use a 3D-compatible BKM-250TG (with serial number 7300001 or higher) and input the left 3D signal to INPUT 1 and the right signal to INPUT 2.

Loosen two screws and remove the cover of an input option port on the rear panel of the monitor.

Make sure the MAIN POWER switch is turned off, and disconnect the AC power cord.

Cover of an input option port

Insert the adaptor facing the board as shown below.

Board

Push the adaptor in until it is firmly fit into the connector inside the monitor, then tighten the two screws to secure the adaptor.

Installing an Input Adaptor (BVM-F170)

For connecting Dual-link HD-SDI signals

To connect the cable

When the BKM-243HS or BKM-244CC adaptors are used, install the Link A signal to OPTION 1 or 3, and the

INPUT 1

INPUT 2

Chapter 2 Preparations

For 3D signal analyzing function

Use a 3D-compatible BKM-250TG (with serial number 7300001 or higher) and input the left 3D signal to INPUT 1 and the right signal to INPUT 2.

Example of Dual-link cable connection

INPUT 1

INPUT 2

INPUT 1

INPUT 2

OPTION 3 and 4

OPTION 1 and 2

When the BKM-250TG is used, install the Link A signal to INPUT 1, and the Link B signal to INPUT 2.

Installing an Input Adaptor (BVM-F170)

Attaching the Bracket

Mounting the Unit in a

(BVM-F250)

You can prevent falling of the monitor by using the supplied bracket.

Remove three screws from the bracket.

Chapter 2 Preparations

Bracket (supplied)

Attach the bracket on the rear panel of the monitor with the three removed screws.

Rack (BVM-F170)

To mount the unit in an EIA standard 19-inch rack, use the supplied rack mount brackets and screws.

Remove the four feet from the bottom of the unit.

Attach the rack mount brackets to each side of the unit with the rack mount attachment screws.

Rack mount bracket

Rack mount attachment screws

Screw the rack mount brackets to the rack to mount the unit.

Attach a piece of string, etc. to the bracket and secure it to the floor or wall.

Bracket

String, etc.

Use the commercially available screws that match the size of the rack’s holes.

Rack

Attaching the Bracket (BVM-F250) / Mounting the Unit in a Rack (BVM-F170)

Connections (BVM-F250)

Note on connecting the cable to the DC 5V OUT connector

Be sure to plug the male connector of the cable into the DC 5V OUT connector of the monitor. Insert the connector so as to fit the shape of the DC 5V OUT connector.

Plug the male connector into the monitor.

Connecting the Controller (BKM16R)

BVM-F250

DC 5V OUT connector

NETWORK switch t Set to PEER TO

PEER.

LAN (10/100) connector

SMF-700, etc.

Chapter 2 Preparations

Controller (BKM-16R)

Turn off the MAIN POWER switch of the monitor

DC 5V/12V IN connector

NETWORK switch tSet to PEER TO PEER.

LAN (10/100) connector

before connecting the units.

Set the NETWORK switches of the monitor and the controller to PEER TO PEER.

Connect the LAN (10/100) connector of the monitor and the LAN (10/100) connector of the controller by using the SMF-700 or the cable supplied with the BKM-37H/38H, or a 10BASE-T/100BASE-TX straight LAN cable (shielded-type, optional).

Note

When an optional LAN cable is connected, use a shielded-type cable to prevent a malfunction due to noises.

Connect the DC 5V OUT connector of the monitor and the DC 5V/12V IN connector of the controller by using the SMF-700 or the cable supplied with the BKM-37H/ 38H. Or connect the output cable of the AC adaptor supplied

Connections (BVM-F250)

with the controller to the DC 5V/12V IN connector of the controller.

Connecting the Multiple Units with the LAN

The controller controls up to 32 monitors. Up to four controllers are connected to one monitor in single mode.

Chapter 2 Preparations

Note

The controller cannot control monitors in another subnetwork.

NETWORK switch tSet to LAN.

BVM-F250

LAN (10/100) connector

BVM-F250

LAN (10/100) connector

Notes

• When an optional LAN cable is connected, use a shielded-type cable to prevent a malfunction due to noises.

• We recommend to use an optional switching hub with auto selection function (AUTO MDI/MDI-X) of a straight/cross cable.

Connect the output cable on the AC adaptor supplied with controller to the DC 5V/12V IN connector of the controller.

Note

When the multiple units are connected, set for the LAN before setting the NETWORK switch to LAN (page

36).

Set the NETWORK switches of each monitor and the controller to LAN.

AC adaptor (supplied with the BKM-16R)

Switching hub (recommended: with AUTO MDI/MDI-X function)

DC 5V/12V IN connector

Controller (BKM-16R)

NETWORK switch tSet to LAN.

Turn off the MAIN POWER switch of the monitor

LAN (10/100) connector

before connecting the units.

Connect to the network by using a 10BASE-T/ 100BASE-TX cable (shielded-type, optional).

Connections (BVM-F250)

+ 112 hidden pages