Sony BKDS-7003, DVS-7150, BKDS-7031, BKDS-7030, BKDS-7075 Installation Manual

...

DIGITAL VIDEO SWITCHER

DVS-7150

SWITCHER CONTROL PANEL

BKDS-7017

BKDS-2031 BKDS-7001 BKDS-7003 BKDS-7030 BKDS-7031 BKDS-7033 BKDS-7075 BKDS-7091 BKDS-7110 BKDS-7111 BKDS-7113

BKDS-7161 BKDS-7163 BKDS-7280 BKDS-M1690 BZS-7080

BKDS-7134

INSTALLATION MANUAL 1st Edition

! WARNING

This manual is intended for qualified service personnel only. To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel.

! WARNUNG

Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt. Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung dazu besitzen.

! AVERTISSEMENT

Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres. Pour toute réparation faire appel à une personne compétente uniquement.

DVS-7150 Serial No. 10001 and Higher BKDS-2031 Serial No. 10001 and Higher BKDS-7001 Serial No. 10001 and Higher BKDS-7003 Serial No. 10001 and Higher BKDS-7017 Serial No. 10001 and Higher BKDS-7030 Serial No. 10001 and Higher BKDS-7031 Serial No. 10001 and Higher BKDS-7033 Serial No. 10001 and Higher BKDS-7075 Serial No. 10001 and Higher BKDS-7091 Serial No. 10001 and Higher BKDS-7110 Serial No. 10001 and Higher BKDS-7111 Serial No. 10001 and Higher BKDS-7113 Serial No. 10001 and Higher

BKDS-7134 Serial No. 10001 and Higher BKDS-7161 Serial No. 10001 and Higher BKDS-7163 Serial No. 10001 and Higher BKDS-7280 Serial No. 10001 and Higher BKDS-M1690 Serial No. 10001 and Higher BZS-7080 Serial No. 10001 and Higher

WARNING

This unit has no power switch. When installing the unit, incorporate a readily accessible disconnect device in the fixed wiring, or connect the power cord to a socket-outlet which must be provided near the unit and easily accessible, so that the user can turn off the power in case a fault should occur.

WARNUNG

Dieses Gerät hat keinen Netzschalter. Beim Einbau des Geräts ist daher im Festkabel ein leicht zugänglicher Unterbrecher einzufügen, oder das Netzkabel mu befindlichen, leicht zugänglichen Wandsteckdose verbunden werden, damit sich bei einer Funktionsstörung die Stromversorgung zum Gerät jederzeit unterbrechen lä

Attention-when the product is installed in Rack:

1. Prevention against overloading of branch circuit

When this product is installed in a rack and is supplied power from an outlet on the rack, please make sure that the rack does not overload the supply circuit.

mit einer in der Nähe des Geräts

2. Providing protective earth

When this product is installed in a rack and is supplied power from an outlet on the rack, please confirm that the outlet is provided with a suitable protective earth connection.

3. Internal air ambient temperature of the rack

When this product is installed in a rack, please make sure that the internal air ambient temperature of the rack is within the specified limit of this product.

4. Prevention against achieving hazardous condition due to uneven mechanical loading

When this product is installed in a rack, please make sure that the rack does not achieve hazardous

condition due to uneven mechanical loading.

Manual Structure

Purpose of this manual .............................................................................................. 3

Related manuals......................................................................................................... 3

Contents ..................................................................................................................... 4

1. Installation

1-1. Operating Environment............................................................................... 1-1

1-2. Power Supply .............................................................................................. 1-1

1-2-1. Power Switch for Service (Control panel) .................................1-1

1-2-2. Power Specifications ..................................................................1-1

1-2-3. Power Cord.................................................................................1-1

1-3. Connectors...................................................................................................1-2

1-4. Input and Output Signals of Connectors ..................................................... 1-3

1-4-1. DVS-7150 ..................................................................................1-3

1-4-2. BKDS-7017................................................................................ 1-6

1-5. Example of System Connection ..................................................................1-8

2. Installation of DVS-7150

2-1. External Dimensions ................................................................................... 2-1

2-2. Rack Mounting............................................................................................ 2-2

3. Installation of Control Panel

3-1. External Dimensions ................................................................................... 3-1

3-2. Installation Space to Console ......................................................................3-2

3-3. Installation to Console.................................................................................3-3

3-4. Replacement of Key Tops........................................................................... 3-4

DVS-7150E IM

4. Installation of Options

4-1. Installation of Plug-in Boards .....................................................................4-2

4-2. Combination of Optional boards.................................................................4-4

4-2-1. Function of optional boards .......................................................4-4

4-2-2. Relation between optional boards and rear panel connectors ....4-4

4-3. Installation of Options for DVS-7150.........................................................4-6

4-3-1. Removing and Installing of Front Panel ....................................4-6

4-3-2. Inserting/Pulling Out of Plug-in Boards ....................................4-7

4-3-3. Installation of Optional Boards ..................................................4-8

4-3-4. Installation of BKDS-M1690

(Redundant Power Supply Unit) ..............................................4-11

4-4. Installation of Options for Control Panel ..................................................4-12

4-4-1. Opening and Closing of Panel..................................................4-12

4-4-2. Turning On/Off the Power .......................................................4-13

4-4-3. Installation of BKDS-7001 (Control Port Expansion Board) ..4-14

4-4-4. Installation of BKDS-7003 (Source Name Display Unit)........4-15

4-4-5. Installation of BKDS-7031 Track Ball ....................................4-17

4-4-6. Installation of Option Panels (BKDS-7030/7031/7033) ..........4-18

4-4-7. Joining of BKDS-7075 (Control Panel Remote Adaptor) .......4-21

4-4-8. Connection of BKDS-7075 to Control Panel...........................4-25

4-4-9. Installation of BKDS-7091 (Redundant Power Supply Unit)

(BKDS-7017) ...........................................................................4-26

5. Confirmation in Installation

5-1. Switch Settings on Boards and LEDs Description......................................5-1

5-1-1. DVS-7150 ..................................................................................5-1

5-1-2. BKDS-7134................................................................................5-6

5-1-3. BKDS-7017................................................................................5-7

5-2. Hard Reset.................................................................................................5-11

5-3. Adjustment of Secondary Power Supply Voltage.....................................5-11

5-3-1. DVS-7150 ................................................................................5-11

5-3-2. BKDS-7017..............................................................................5-13

5-4. Adjustment of Operation Power for Fader Lever .....................................5-15

6. Initial Set-up of System

6-1. Operation and Saving of Set-up Data..........................................................6-1

6-2. Installation of Program (BZS-7080) ...........................................................6-4

6-2-1. Down Load of Program..............................................................6-5

6-2-2. Initializing of Data on RAM ......................................................6-6

6-2-3. Initializing of “Nonvolatile Memory”........................................6-7

6-3. Set-up ..........................................................................................................6-8

DVS-7150E IM

Purpose of this manual

Related manuals

Manual Structure

This manual is the installation manual of Digital Video Switcher DVS-7150. This manual is intended for use by trained system and service engineers, and describes the information when installing DVS-7150.

The following manuals are prepared for DVS-7150. The part numbers of these manuals as of Novemver, 1998 describe.

. User’s Guide (Supplied with BZS-7080)

This manual describes the application and operation of DVS-7150.

. Operation Manual (Supplied with DVS-7150)

This manual describes the overview, system configuration examples and specifications of options.

. Maintenance Manual Part 1 (Supplied with DVS-7150)

This manual describes the information for the periodic maintenance, and the information for the service with predicated on the replacement of the principal blocks and mounted circuit boards. Part number : 3-201-448-01

. Maintenance Manual Part 2

The following manuals describe the detailed service information. For obtaining, please contact your local Sony’s sale/service office. All Supplements will publish at February, 1999.

Volume 1 (Block diagrams and Frame wirings)

Part number : 9-967-615-03

Supplement 4 Part number : 9-967-615-84

Volume 2 (Spare parts, Service overview and Replacement of main parts)

Part number : 9-967-616-03

Supplement 5 Part number : 9-967-616-85

Volume 3 (Semiconductor pin assignments)

Part number : 9-967-617-03

Supplement 3 Part number : 9-967-617-83

Volume 4 (Board layouts)

Part number : 9-967-618-03 Supplement 4 Part number : 9-967-618-84

DVS-7150E IM

. Maintenance Manual Part 2

Volume 5 (Schematic diagrams 1 A through I)

Part number : 9-967-624-03

Supplement 3 Part number : 9-967-624-83

Volume 6 (Schematic diagrams 2 K through Z)

Part number : 9-967-625-02 Supplement 4 Part number : 9-967-625-84

This manual is organized by following sections.

Section 1 Installation

This section describes the operating environment, power supply, connectors, input and output signals of connectors, and example of system connection.

Section 2 Installation of DVS-7150

This section describes the external dimensions and rack mounting.

Section 3 Installation of Control panel

This section describes the external dimensions, installation space to console, rack mounting and replacement of key tops.

Section 4 Installation of Options

This section describes the installation of plug-in boards, combinations of optional boards and installation of options.

Section 5 Confirmation in Installation

This section describes the switch settings on boards and LEDs description,hard reset,confirmation of secondary power supply voltage and adjustment of operation power for fader lever.

Section 6 Initial Set-up of System

This section describes the operation and saving of set-up data, installation of program, set-up.

DVS-7150E IM

Section 1

Installation

1-1. Operating Environment

. Install the unit in a well ventilated place to prevent a

temperature rise in the unit. Never cover the ventilation holes of the outer frame.

. Never install the unit near a heat source because the

environmental temperature during operation should be 5 dC to 40 dC.

1-2. Power Supply

1-2-1. Power Switch for Service

(Control panel)

The power switches for service of the control panels are placed only in the unit. When installing the unit, incorporate a readily accessible disconnect device in the fixed wiring, so that the operator/ engineer power in case a fault should occur.

1-2-3. Power Cord

The power cords are not supplied with DVS-7150 and the control panel. Be sure to use the power cords that are applicable to the places in the world. To avoid a fire or an electric shock, be sure to use the designated power cord. And do not damage to the power cord.

For the customer in the U.S.A. and Canada Required Parts

1 Power Cord, 125 V 10 A (2.4 m) : 1-557-377-11

For the customer in the United Kingdom Required Parts

DK-2401 (EK) 1 Power Cord, 250 V 10 A (2.4 m)

AC inlet

1-2-2. Power Specifications

Power requirements : 100 to 240 V AC ± 10%

50/60 Hz

Current consumption

DVS-7150 : 4 to 2 A BKDS-7017 : 1.0 A (max.)

As the inrush current at turn-on is the maximum 20 A, the capacity of the AC power must be commensurate in it with the inrush current of the maximum 20 A for the processor and the control panel respectively. If the capacity of the AC power is not the adequately large, the breaker of the AC power at the supply side will operate or the unit will abnormal operate.

For the customer in the all European countries except the United Kingdom

Required Parts

DK-2401 (AE)

1 Power Cord, 250 V 10 A (2.4 m)

AC inlet

For the customer outside of the area as shown above, please consult with local Sony’s sale/service office.

DVS-7150E IM

1-1

1-3. Connectors

When connecting cables to various connectors on the rear panel at the time of installing, connecting or servicing, connect the following connectors or their equivalents.

1. DVS-7150

Connector function name Connector parts No. and on rear panel name of cable

(*2)

(* 2)

(*2)

(* 2)

(*2)

(* 2)

(* 2) (* 2)

D-sub 9-pin, Male

Connector 9-pin, Male

1-560-651-00

(*1)

Junction Shell 9-pin

1-561-749-00

D-sub 25-pin, Male

Connector 25-pin, Male

1-560-904-11

(*1)

Junction Shell 25-pin

1-563-377-11

Main Power Supply Cable (For the details of the cable, refer to Section 1-2-3.)

PANEL 1 DME 1 to 2 SERIAL TALLY TERMINAL EDITOR-A/REMOTE 1 EDITOR-B/REMOTE 2 PANEL 2/REMOTE 3 MATRIX/REMOTE 4

GPI

PRIMARY INPUTS 1 to 24 BNC Coaxial Connector Plug CRK INPUT 1 to 2 REF INPUT REF OUTPUT AUX BUS OUTPUTS 1 to 6 ME OUTPUTS 1 to 2 PGM OUTPUTS 1 to 4 PVW OUTPUTS 1 to 2 EDIT PVW OUTPUT

AC IN

2. BKDS-7017

Connector function name Connector parts No. and on rear panel name of cable

(*2)

D-sub 9-pin, Male

Connector 9-pin, Male

1-560-651-00

(*1)

Junction Shell 9-pin

SWITCHER DME TERMINAL 1 to 2 REMOTE 1 to 4

1-561-749-00

OPTION PANEL

(*2)

BVS Cable

1-574-993-11

(*2)

AC IN

Main Power Supply Cable (For the details of the cable, refer to Section 1-2-3.)

(*1):The following solderless contact must be used for the plug.

AWG #18 to #22:1-566-493-00 AWG #22 to #24:1-564-774-00 AWG #24 to #30:1-564-775-00

(*2):For the customers in europe

When connecting the cables to the following connectors, attach the two ferrite cores that are packed with each model to the two connectors at the both sides of the cable.

1-2

DVS-7150E IM

1-4. Input and Output Signals of

Connectors

The input and output signals of the connectors on the rear panel are specified in the following table. And refer to the following illustration for the pin positions of the connectors.

1-4-1. DVS-7150

1-4. Input and Output Signals of Connectors

[D-SUB 25 PIN • FEMALE]

EXT VIEW

[D-SUB 9 PIN • FEMALE]

EXT VIEW

(*1) <CONTROLLER>: Controlling device (*2) <DEVICE> : Controlled device

PANEL 1 : RS-422A (D-sub 9-pin.Female) <DEVICE>

Pin No. Signal Name Function

1 GND Frame ground 2 TX-A Transmitted data (_) 3 RX-B Received data (+) 4 GND Common ground 5 FIELD (+) Field signal output (+) 6 GND Common ground 7 TX-B Transmitted data (+) 8 RX-A Received data (_) 9 FIELD (_) Field signal output (_)

(*2)

from Control panel BKDS-7017

PANEL1

DME1

SERIAL TALLY

DME2

MATRIX /REMOTE4

GPI

PANEL2 /REMOTE3

TERMINAL

EDITOR-B /REMOTE2 EDITOR-A /REMOTE1

Rear panel

PANEL 2/REMOTE 3 : RS-422A (D-sub 9-pin.Female) <DEVICE>

(* 2)

from Control panel

Pin No. Signal Name Function

1 GND Frame ground 2 TX-A Transmitted data (_) 3 RX-B Received data (+) 4 GND Common ground 5 VD-B Transmited VD signal (+) 6 GND Common ground 7 TX-B Transmitted data (+) 8 RX-A Received data (_) 9 VD-A Transmited VD signal (_)

(*3):Control Panel BKDS-2010 etc. (PANEL 2)

Keyer Remote Panel BKDS-7060 etc. (REMOTE 3)

(* 3)

DVS-7150E IM

1-3

1-4. Input and Output Signals of Connectors

SERIAL TALLY : RS-422A (D-sub 9-pin.Female) <CONTROLLER>

(*1)

For the SERIAL TALLY connector, refer to the Protocol Manual of DVS-8000 Series.

Pin No. Signal Name Function

1 FG Frame ground 2 RX-A Received data (_) 3 TX-B Transmitted data (+) 4 GND Common ground 5 __ 6 GND Common ground 7 RX-B Received data (+) 8 TX-A Transmitted data (_) 9 FG Frame Ground

DME 1, 2 : RS-422A (D-sub 9-pin.Female) <DEVICE>

(*2)

from Digital multi effects DME-3000/7000

etc.

Pin No. Signal Name Function

1 FG Frame ground 2 TX-A Transmitted data (_) 3 RX-B Received data (+) 4 GND Common ground 5 __ 6 GND Common ground 7 TX-B Transmitted data (+) 8 RX-A Received data (_) 9 FG Frame Ground

EDITOR-A/REMOTE 1 : RS-422A (D-sub 9-pin.Female) <DEVICE>

Pin No. Signal Name Function

1 FG Frame ground 2 EDT A TX-A Transmitted data (_) 3 EDT A RX-B Received data (+) 4 GND Common ground 5 __ 6 GND Common ground 7 EDT A TX-B Transmitted data (+) 8 EDT A RX-A Received data (_) 9 FG Frame Ground

(*5):Editing control Unit BVE-9100 etc. (EDITOR A)

(*2)

from Editor

(*5)

EDITOR-B/REMOTE 2 : RS-422A (D-sub 9-pin.Female) <DEVICE>

Pin No. Signal Name Function

1 FG Frame ground 2 TX-A Transmitted data (_) 3 RX-B Received data (+) 4 GND Common ground 5 __ 6 GND Common ground 7 TX-B Transmitted data (+) 8 RX-A Received data (_) 9 FG Frame Ground

(*6):Editing control Unit BVE-9100 etc. (EDITOR B)

(*2)

from Editor

(*6)

TERMINAL : RS-232C (D-sub 9-pin.Female)

to Terminal

MATRIX/REMOTE 4

Pin No. Signal Name Function

1 FG Frame ground 2 RX-A Received data (_) 3 TX-B Transmitted data (+) 4 GND Common ground 5 __ 6 GND Common ground 7 RX-B Received data (+) 8 TX-A Transmitted data (_) 9 FG Frame Ground

(*4)

: RS-422A (D-sub 9-pin.Female)

(*1)

to Routing switcher

1-4

Pin No. Signal Name Function

1 DCD Data Carrier detect 2 RXD Received data 3 TXD Transmitted data 4 DTR Data terminal ready 5 SG Signal ground 6 DSR Data set ready 7 RTS Request to send 8 CTS Clear to send 9 __

(*7) :Pins 1, 4 and 6 are short-circuited each other on the CN-1751 board.

(*7)

DVS-7150E IM

GPI : (D-sub 25-pin.Female) INPUT x 8, TTL OUTPUT x 4, relay contact 30 V 0.1 A (resistance load) OUTPUT x 4, open collector 30 V rated voltage GPI timing : Refer to User’s Guide

Pin No. Signal Name Function

1 GND Ground 2 GND Ground 3 GPI IN 2 4 GPI IN 4 5 GPI IN 6 6 GPI IN 8 7 GPI OUT 1B 8 GPI OUT 2B 9 GPI OUT 3B 10 GPI OUT 4B 11 GPI OUT 6 12 GPI OUT 8 13 GPI OUT COM Ground for open collector output 14 GND Ground 15 GPI IN 1 16 GPI IN 3 17 GPI IN 5 18 GPI IN 7 19 GPI OUT 1A 20 GPI OUT 2A 21 GPI OUT 3A 22 GPI OUT 4A 23 GPI OUT 5 24 GPI OUT 7 25 GPI OUT COM Ground for open collector output

General-purpose input

General-purpose relay output (B)

General-purpose open collector output

General-purpose input

General-purpose relay output (A)

General-purpose open collector output

1-4. Input and Output Signals of Connectors

(*8)

(*9)

(*8)

(*9)

A and B of same number constitute a pair of relay contacts.

(*8) : <Relay>

GPI OUT x B GPI OUT x A

x;1-4

(*9) : <Open collector output>

GPI OUT 5-8

GPI OUT COM

DVS-7150E IM

1-5

1-4. Input and Output Signals of Connectors

1-4-2. BKDS-7017

[D-SUB 25 PIN • FEMALE]

EXT VIEW

[D-SUB 9 PIN • FEMALE]

EXT VIEW

m (*1) <CONTROLLER> : Controlling device

1. Main Panel SWITCHER : RS-422A (D-sub 9-pin.Female)

(*1)

to Processor DVS-7150

SWITCHER DME TERMINAL1 TERMINAL2

OPTION PANEL REMOTE1 REMOTE2 REMOTE3 REMOTE4

Rear panel

REMOTE 1 to 4

(*2)

: RS-422A (D-sub 9-pin.Female)

(*1)

to External Device

Pin No. Signal Name Function

1 FG Frame ground 2 RX-A Received data (_) 3 TX-B Transmitted data (+) 4 GND Common ground 5 FIELD (+) Field signal input (+) 6 GND Common ground 7 RX-B Received data (+) 8 TX-A Transmitted data (_) 9 FIELD (_) Field signal input (_)

DME : RS-422A (D-sub 9-pin.Female) <CONTROLLER>

(*1)

to Digital multi effects DME-3000/

7000 etc.

Pin No. Signal Name Function

1 FG Frame ground 2 RX-A Received data (_) 3 TX-B Transmitted data (+) 4 GND Common ground 5 _ NC 6 GND Common ground 7 RX-B Received data (+) 8 TX-A Transmitted data (_) 9 __

Pin No. Signal Name Function

1 FG Frame ground 2 RX-A Received data (_) 3 TX-B Transmitted data (+) 4 GND Common ground 5 __ 6 GND Common ground 7 RX-B Received data (+) 8 TX-A Transmitted data (_) 9 __

(*2) :BKDS-7001 (Option : IF-523 board) is in need of using the REMOTE

from 1 to 4.

TERMINAL 1, 2 : RS-232C (D-sub 9-pin.Female)

to Terminal

Pin No. Signal Name Function

1 DCD Received line signal detector signal 2 RX Received data 3 TX Transmitted data 4 DTR Data terminal ready signal 5 GND Signal ground 6 DSR Data set ready signal 7 RTS Request to send signal 8 CTS Clear to send signal 9 __

(*3) :Pins 1, 4 and 6 are short-circuited each other on the CN-1149 board. (*4):Pins 7 and 8 are short-circuitede each other on the CN-1149 board.

(*3)

(* 3)

(*4)

(* 4)

(*3)

1-6

DVS-7150E IM

OPTION PANEL : (D-sub 25-pin.Female)

to Adaptor box (BKDS-7075)

Pin No. Signal Name Function

1 GND Ground 2 +12 V Power supply +12 V 3 SCLK Serial clock for switch read and LED

light 4 GND Ground 5 WDT LED light data 6 IWLD Control signal for switch read and LED

light 7 GND Ground 8 TCLK Serial clock for character display 9 TWDT Indicate data for character display 10 GND Ground 11 TBLANK Disable signal for character display 12 GND Ground 13 GND Ground 14 +12 V Power supply +12 V 15 +12 V Power supply +12 V 16 BLANK LED light disable signal 17 GND Ground 18 SEQ Control signal for switch read and LED

light 19 RDT Switch read data 20 GND Ground 21 TSEQ Control signal for character display 22 TQCLK Control signal for character display 23 +12 V Power supply +12 V 24 +12 V Power supply +12 V 25 GND Ground

1-4. Input and Output Signals of Connectors

DVS-7150E IM

1-7

1-5. Example of System Connection

1234567891011121314151617181920212223

Y1U1V1S1Y2U2V2

TERMINAL

MATRIX/REMOTE 4

ROUTER

SUPER V/K

DME V/K

VTR

REF OUT

REF IN

CAMERA

SW'ER

DME PANEL

DME-7000

BKDS-7016/7016L/7017

INPUTS

COMPONENT

ANALOG

CRK IN

INPUTS

DIGITAL

INPUTS

DIGITAL

PRIMARY

CONTROL PANEL

KEYER REMOTE

BKDS-7060

CONTROL

OUT1

CONTROL

OUT2

REMOTE 3

PANEL 2

SUB PANEL

BKDS-2010

SW'ER

CCU

DCU

DVW-500

REC

SOURCE

LINE IN

BVW-75

BVW-75D

DVR-2000

YUV

ROUTER

DVS-V6464B

TALLY

INTERFACE

UNIT

BKDS-7700

GPI

SERIAL

TALLY

D1 LIVE SW'ER

DVS-7150

EDIT PVW

EDITOR-B

/REMOTE 2

EDITOR-A

/REMOTE 1

AUX3

AUX4

DME2

AUX5

AUX6

AUX1

AUX2

DME1

PGM1

PGM2

PVW1

PVW2

PGM3

PGM4

ME OUT1

ME OUT2

PANEL 2

/REMOTE 3 1

PANEL

SWITCHER

MAIN PANEL

REMOTE2

DME

DME2

VKVKZ

SW'ER PANEL

VKZ

SW'ER

DME PANEL

DME-7000

DME1

SW'ER PANEL

VKZ

MONITOR

WFM

PGM

PVW

ME1

BVE-9100

EDITOR

DMEVTR AB

KEY BOARD

1-5. Example of System Connection

1. D1 LIVE SWITCHER SYSTEM

1-8

DVS-7150E IM

2. D2 LIVE SWITCHER SYSTEM

1234567891011121314151617181920212223

Y1U1V1S1Y2U2V2

TERMINAL

MATRIX/REMOTE 4

ROUTER

SUPER V/K

DME V/K

VTR

REF OUT

REF IN

CAMERA

DME PANEL

SW'ER

DME PANEL

DME-7000

BKDS-7016/7016L/7017

INPUTS

COMPONENT

ANALOG

CRK IN

INPUTS

DIGITAL

COMPOSITE

ANALOG

PRIMARY

INPUTS

CONTROL PANEL

KEYER REMOTE

BKDS-7060

CONTROL

OUT1

CONTROL

OUT2

REMOTE 3

PANEL 2

SUB PANEL

BKDS-2010

SW'ER

CCU

DVR-28

REC

SOURCE

LINE IN

BVW-75

DVR-20

BVW-D265

YUV

ROUTER

DVS-V6464B

TALLY

INTERFACE

UNIT

BKDS-7700

GPI

SERIAL

TALLY

D2 LIVE SW'ER

DVS-7150

EDIT PVW

EDITOR-B

/REMOTE 2

EDITOR-A

/REMOTE 1

AUX3

AUX4

DME2

AUX5

AUX6

AUX1

AUX2

DME1

PGM1

PGM2

PVW1

PVW2

PGM3

PGM4

ME OUT1

ME OUT2

PANEL 2

/REMOTE 3 1

PANEL

SWITCHER

MAIN PANEL

REMOTE2

DME

DME2

VKVKZ

SW'ER PANEL

VKZ

SW'ER

DME PANEL

DME-7000

DME3

VKVKZ

VKZ

SW'ER

DME PANEL

DME-7000

DME1

SW'ER PANEL

VKZ

KZKVV

DME4

MONITOR

WFM

PGM

PVW

ME1

BVE-9100

EDITOR

DMEVTR AB

KEY BOARD

1-5. Example of System Connection

DVS-7150E IM

1-9

2-1. External Dimensions

Section 2

Installation of DVS-7150

475

146

221(5UNIT)

23.5

482 465

424

(Front view)

DIGITAL VIDEO SWITCHER DVS-7150

88.2

83.7

(Top view)

450

304.8

101.6

254

(Right side view)

Unit : mm

DVS-7150E IM

2-1

2-2. Rack Mounting

DVS-7150 can be mounted in a 19-inch standard rack. Be sure to use the optional rack mount rail RMM-

30.

< Required Parts > . Rack mount rail (RMM-30)

Rails with bracket : 2 pcs Screw (B5 x 8) : 8 pcs

. Screw (BVTT4 x 8) . Screw for rack mounting (RK5 x 16) : 4 pcs . Ornamental washer for rack mounting : 4 pcs

(Sony part number : 2-297-913-01)

(*1) : DVS-7150 is supplied with the eight screws. Use two of them for the spare parts.

(1) If DVS-7150 is mounted in a 19-inch standard rack, it is recommended to install a ventilation fan to

prevent a temperature rise in the rack. Make sure that all the units in the rack should be operated within the temperature range of 10 dC to 35 dC.

(2) Be sure to use the recommended rail when rack mounting. The unit cannot be installed completely to

a rack by rack angles alone.

(3) It is recommended to fix the rack to the floor with bolts. When the unit is pulled out from the rack,

this will prevent its fall.

(4) An installation manual is supplied with the rack mount rail RMM-30. However follow the instruc-

tions in this manual. Because the rack mounting procedures of DVS-7150 differ somewhat from the procedures explained in RMM-30 installation manual.

(5) Be sure to mount in the rack with two-person or more.

(*1)

: 6 pcs

2-2

DVS-7150E IM

Procedures

(1) Pull out the inner member while pressing the stopper of the rack mount rail RMM-30. (Fig. 1) (2) Secure the inner member to the unit by the six screws (BVTT 4 x 8) supplied with DVS-7150.

Remove the feet of the unit as required. (Fig. 2)

Inner menber

BVTT4 x 8

Outer menber

Stopper

Feet

DVS-7150

2-2. Rack Mounting

Inner menber

(Fig. 1) (Fig. 2)

Feet

(3) Loosen the screws secured the rear bracket to the outer member. Adjust the position of the rear

bracket in line with the rack depth. (Fig. 3)

(4) Temporarily secure the front and rear brackets to the outside of the rack by the eight screws (B5 x 8)

supplied with RMM-30. (Fig. 4)

Rear braket

Outer member

(Fig. 3)

Rack (Left)

Front bracket

12.7

31.75

12.7

31.75

Front bracket

Rack (Right)

Outer member

12.7

BVTT4 x 8

Front bracket

B5 x 8

DVS-7150E IM

B5 x 8

Outer member

(Fig. 4)

2-3

2-2. Rack Mounting

(5) For installing the unit in the rack, press the inner members fully to the outer members while pressing

the stoppers of the inner members. (Fig. 5)

(6) After confirming that the unit can be moved smoothly, tighten the screws (B5 x 8) secured tempo-

rarily in the step (4).

When securing the front brackets to the rack by screws, pull out the unit about 20 cm (8 inches) from the rack, and fasten the screws of the front brackets to the rack.

(7) After installing the unit in the rack, secure the unit to the rack by the prepared four screws (RK5 x

16) and four ornamental washers. (Fig. 6)

Rack

DVS-7150

RK5 x 16

DVS-7150

Rack

Ornamental washer

RK5 x 16

Outer menber

Stopper

Inner member

(Fig. 5) (Fig. 6)

. When DVS-7150 is mounted in a rack, the maximum traveling distance is illustrated below.

581

Maximum travelling distance

Ornamental washer

221.2

88.6

Distance to the center of the slide rail

Height of the unit mounted in a Rack

2-4

Unit : mm

DVS-7150E IM

3-1. External Dimensions

Main Panel BKDS-7017

Section 3

Installation of Control Panel

496

AUX

M/E

PGM/PST

DSK

PGM

PST

AUX DELEGATION

760

MANUAL

INSTRUCTION SEE

TERMINAL 2

REMOTE 2

REMOTE 3 REMOTE 4

DME

TERMINAL 1

25 14

OPTION PANEL

REMOTE 1

SWITCHER

850

TOP MENU

UTILITY

11076.8

385

DOWNSTREAM KEYER

DVS-7150system

3015

DVS-7150E IM

Unit : mm

3-1

3-1. External Dimensions 3-2. Installation Space to Console

BKDS-7075

212

78.5

132

2-M4

3-2. Installation Space to Console

Control panel can be installed in the console by drilling holes in the console in the locations specified below.

BKDS-7017

(52)

470

500

483 110

Unit : mm

7.2

3-2

11-M4

185 185

418

185 185

824 854

418 9

198 198

Approx.75d

Unit : mm

DVS-7150E IM

+ 54 hidden pages

Sony BKDS-7003, DVS-7150, BKDS-7031, BKDS-7030, BKDS-7075 Installation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Table of Contents

Purpose of this manual

Related manuals

Manual Structure

Contents

Installation

1-1. Operating Environment

1-2. Power Supply

1-2-3. Power Cord

1-2-2. Power Specifications

1-3. Connectors

1-4-1. DVS-7150

1-4. Input and Output Signals of Connectors

1-4-2. BKDS-7017

1-5. Example of System Connection

2-1. External Dimensions

Installation of DVS-7150

2-2. Rack Mounting

3-1. External Dimensions

Installation of Control Panel

3-2. Installation Space to Console