How it Works
Sony
Loading...
BKDS-7011R
Installation Manual
110 pgs3.08 Mb0

Sony BKDS-7011, BKDS-7012, BKDS-7011R, BKDS-7011LR, BKDS-7021 Installation Manual

...
DIGITAL VIDEO SWITCHER
DVS-7000A
INSTALLATION MANUAL 1st Edition
BKDS-7021/7021R/7021LR BKDS-7022/7022R/7022LR BKDS-7023/7023R/7023LR
TYPE-3D SWITCHER CONTROL PANEL
BKDS-7011/7011R/7011LR BKDS-7012
TYPE-4D SWITCHER CONTROL PANEL
! W ARNING
This manual is intended for qualified service personnel only. To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel.
! W ARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt. Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung dazu besitzen.
! AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres. Pour toute réparation faire appel à une personne compétente uniquement.
DVS-7000A Serial No. 10001 and Higher BKDS-2031 Serial No. 10001 and Higher BKDS-2032 Serial No. 10001 and Higher BKDS-2041 Serial No. 10001 and Higher BKDS-2070 Serial No. 10001 and Higher BKDS-7001 Serial No. 10001 and Higher BKDS-7011 Serial No. 10001 and Higher BKDS-7012 Serial No. 10001 and Higher BKDS-7021 Serial No. 10001 and Higher BKDS-7022 Serial No. 10001 and Higher BKDS-7023 Serial No. 10001 and Higher BKDS-7011R Serial No. 10001 and Higher BKDS-7021R Serial No. 10001 and Higher BKDS-7022R Serial No. 10001 and Higher BKDS-7023R Serial No. 10001 and Higher BKDS-7011LR Serial No. 10001 and Higher BKDS-7021LR Serial No. 10001 and Higher BKDS-7022LR Serial No. 10001 and Higher BKDS-7023LR Serial No. 10001 and Higher BKDS-7030 Serial No. 10001 and Higher
BKDS-7031 Serial No. 10001 and Higher BKDS-7032 Serial No. 10001 and Higher BKDS-7033 Serial No. 10001 and Higher BKDS-7075 Serial No. 10001 and Higher BKDS-7090 Serial No. 10001 and Higher BKDS-7103 Serial No. 10001 and Higher BKDS-7110 Serial No. 10001 and Higher BKDS-7111 Serial No. 10001 and Higher BKDS-7113 Serial No. 10001 and Higher BKDS-7133 Serial No. 10001 and Higher BKDS-7161 Serial No. 10001 and Higher BKDS-7163 Serial No. 10001 and Higher BKDS-7270 Serial No. 10001 and Higher BKDS-7271 Serial No. 10001 and Higher BKDS-7280 Serial No. 10001 and Higher BKDS-7420 Serial No. 10001 and Higher BKDS-7445 Serial No. 10001 and Higher BKDS-7690 Serial No. 10001 and Higher BZS-7020A Serial No. 10001 and Higher
WARNING
This unit has no power switch. When installing the unit, incorporate a readily accessible disconnect device in the fixed wiring, or connect the power cord to a socket-outlet which must be provided near the unit and easily accessible, so that the user can turn off the power in case a fault should occur.
WARNUNG
Dieses Gerät hat keinen Netzschalter. Beim Einbau des Geräts ist daher im Festkabel ein leicht zugänglicher Unterbrecher einzufügen, oder das Netzkabel mu
ß
mit einer in der Nähe des Geräts befindlichen, leicht zugänglichen Wandsteckdose verbunden werden, damit sich bei einer Funktionsstörung die Stromversorgung zum Gerät jederzeit unterbrechen lä
ß
t
Attention-when the product is installed in Rack:
1. Prevention against overloading of branch circuit
When this product is installed in a rack and is supplied power from an outlet on the rack, please make sure that the rack does not overload the supply circuit.
2. Providing protective earth
When this product is installed in a rack and is supplied power from an outlet on the rack, please confirm that the outlet is provided with a suitable protective earth connection.
3. Internal air ambient temperature of the rack
When this product is installed in a rack, please make sure that the internal air ambient temperature of the rack is within the specified limit of this product.
4. Prevention against achieving hazardous
condition due to uneven mechanical loading
When this product is installed in a rack, please make sure that the rack does not achieve hazardous
condition due to uneven mechanical loading.
1
DVS-7000AE IM
Table of Contents
Manual Structure
Purpose of this manual .............................................................................................. 3
About the model names of the control panels ........................................................... 3
Contents ..................................................................................................................... 4
Related manuals......................................................................................................... 5
1. Installation
1-1. Operating Environment............................................................................... 1-1
1-2. Power Supply .............................................................................................. 1-1
1-2-1. Power Switch for Service (Control panel) ................................. 1-1
1-2-2. Power Specifications ..................................................................1-1
1-2-3. Power Cord.................................................................................1-1
1-3. Connectors...................................................................................................1-2
1-4. Input and Output Signals of Connectors .....................................................1-3
1-4-1. DVS-7000A................................................................................1-3
1-4-2. Control Panel..............................................................................1-6
1-5. Examples of System Connection ..............................................................1-11
2. Installation of DVS-7000A
2-1. External Dimensions ...................................................................................2-1
2-2. Rack Mounting............................................................................................ 2-2
3. Installation of Control Panel
3-1. External Dimensions ...................................................................................3-1
3-2. Installation Space ........................................................................................ 3-9
3-3. Installation of MAIN PANEL................................................................... 3-12
3-4. Installation of DISPLAY PANEL.............................................................3-13
3-5. Installation of AUX BUS PANEL
(Only BKDS-702x, 702xR and 702xLR)..................................................3-14
3-6. Installation of Ten Key Unit (Only BKDS-70xxR/70xxLR)....................3-14
3-7. Connection of Control Panel..................................................................... 3-14
3-8. Replacement of Key Tops......................................................................... 3-15
2
DVS-7000AE IM
4. Installation of Options
4-1. Installation of Plug-in Boards ..................................................................... 4-2
4-2. Combination of Optional boards................................................................. 4-4
4-2-1. Function of Optional Boards ......................................................4-4
4-2-2. Relation between Optional Boards and
Rear Panel Connectors ............................................................... 4-4
4-3. Installation of Options for DVS-7000A...................................................... 4-6
4-3-1. Detaching and Attaching of Front Panel ....................................4-6
4-3-2. Inserting/Pulling Out of Plug-in Boards ....................................4-7
4-3-3. Installation of Optional Boards ..................................................4-9
4-3-4. Installation of BKDS-7690 (Redundant Power Supply Unit).. 4-12
4-4. Installation of Options for Control Panel ..................................................4-13
4-4-1. Opening and Closing of Panel..................................................4-13
4-4-2. Turning On/Off the Power Switch ........................................... 4-14
4-4-3. Installation of BKDS-7001 (Control Port Expansion Board) .. 4-15
4-4-4. Installation of BKDS-7031 Track Ball ....................................4-16
4-4-5. Installation of Option Panels (BKDS-7030/7031/7032/7033) .4-18
4-4-6. Joining of BKDS-7075 (Control Panel Remote Adaptor) .......4-29
4-4-7. Installation of BKDS-7090 (Redundant Power Supply Unit).. 4-33
5. Confirmation in Installation
5-1. Switch Settings on Boards and LEDs Description......................................5-1
5-1-1. DVS-7000A................................................................................5-1
5-1-2. BKDS-7133................................................................................ 5-6
5-1-3. Control Panel..............................................................................5-6
5-1-4. BKDS-7090.............................................................................. 5-12
5-2. Adjustment of Secondary Power Supply Voltage.....................................5-13
5-2-1. DVS-7000A..............................................................................5-13
5-2-2. Control Panel............................................................................5-15
5-3. Adjustment of Operation Power for Fader Lever .....................................5-17
6. Initial Set-up of System
6-1. Operation and Saving of Set-up Data..........................................................6-1
6-2. Installation of Program (BZS-7020A) ........................................................6-4
6-2-1. Down Load of Program..............................................................6-5
6-2-2. Initializing of Data on RAM ...................................................... 6-7
6-2-3. Initializing of “Nonvolatile Memory”........................................ 6-8
6-3. Set-up .......................................................................................................... 6-9
6-3-1. Confirmation of the Software Version .....................................6-10
6-3-2. Setting of the Signal Format ....................................................6-10
6-3-3. Setting about the System ..........................................................6-11
6-3-4. Saving Set-up Data to Nonvolatile Memory ............................6-12
DVS-7000AE IM
3
Purpose of this manual
This manual is the installation manual of Digital Video Switcher DVS-7000A. This manual is intended for use by trained system and service engineers, and describes the information when installing DVS-7000A.
About the model names of the control panels
This manual is described the model name of the control panels as shown the table below.
Manual Structure
Model name Short model name Shortest model name
BKDS-7011 BKDS-701x BKDS-70xx BKDS-7012 BKDS-7021 BKDS-702x BKDS-7022 BKDS-7023 BKDS-7011R BKDS-701xR BKDS-70xxR BKDS-7021R BKDS-702xR BKDS-7022R BKDS-7023R BKDS-7011LR BKDS-701xLR BKDS-70xxLR BKDS-7021LR BKDS-702xLR BKDS-7022LR BKDS-7023LR
4
DVS-7000AE IM
Contents
This manual is organized by following sections.
Section 1 Installation
This section describes the operating environment, power supply, connectors, input and output signals of connectors, and example of system connection.
Section 2 Installation of DVS-7000A
This section describes the external dimensions and rack mounting.
Section 3 Installation of Control panel
This section describes the external dimensions, installation space, rack mounting and replacement of key tops.
Section 4 Installation of Options
This section describes the installation of plug-in boards, combinations of optional boards and installation of options.
Section 5 Confirmation in Installation
This section describes the switch settings on boards and LEDs description, Adjust­ment of secondary power supply voltage and adjustment of operation power for fader lever.
Section 6 Initial Set-up of System
This section describes the operation and saving of set-up data, installation of pro­gram, set-up, saving set-up data to nonvolatile memory.
DVS-7000AE IM
5
Related manuals
The following manuals are prepared for DVS-7000A. The part numbers of these manuals as of February, 1999 describe.
..
..
. User’s Guide (Supplied with BZS-7020A)
This manual describes the application and operation of DVS-7000A.
..
..
. Operation Manual (Supplied with DVS-7000A)
This manual describes the overview, system configuration examples and specifications of options.
..
..
. Maintenance Manual Part 1 (Supplied with DVS-7000A)
This manual describes the information for the periodic maintenance, and the information for the service with predicated on the replacement of the principal blocks and mounted circuit boards. Part number : 3-201-864-01
..
..
. Maintenance Manual Part 2
The following manuals describe the detailed service information. For obtaining, please contact your local Sony’s sale/service office.
Volume 1 (Block diagrams and Frame wirings)
Part number : 9-967-615-03
Supplement 4 Part number : 9-967-615-84
Volume 2 (Spare parts, Service overview and Replacement of main parts)
Part number : 9-967-616-03
Supplement 5 Part number : 9-967-616-85
Volume 3 (Semiconductor pin assignments)
Part number : 9-967-617-03
Supplement 3 Part number : 9-967-617-83
Volume 4 (Board layouts)
Part number : 9-967-618-03
Supplement 4 Part number : 9-967-618-84
Volume 5 (Schematic diagrams 1 A through I)
Part number : 9-967-624-03
Supplement 3 Part number : 9-967-624-83
Volume 6 (Schematic diagrams 2 K through Z)
Part number : 9-967-625-02 Supplement 4 Part number : 9-967-625-84
DVS-7000AE IM
1-1
1-2-3. Power Cord
w
The power cords are not supplied with DVS-7000A, the control panels. Be sure to use the power cords that are applicable to the places in the world.
n
The plug holder is not used for the control panels.
n
For the customer outside of the area as shown above, please consult with local Sony’s sale/service office.
AC inlet
2
1
For the customer in the U.S.A. and Canada Required Parts
1 Power Cord, 125 V 10 A (2.4 m) : 1-557-377-11 2 Plug Holder B (Black) : 2-990-242-01
2
AC inlet
1
For the customer in the United Kingdom Required Parts
DK-2401 (EK)
1 Power Cord, 250 V 10 A (2.4 m) 2 Plug Holder B (Black) : 2-990-242-01
AC inlet
2
1
For the customer in the all European countries except the United Kingdom
Required Parts
DK-2401 (AE)
1 Power Cord, 250 V 10 A (2.4 m) 2 Plug Holder B (Black) : 2-990-242-01
Section 1
Installation
1-1. Operating Environment
. Install the unit in a well ventilated place to prevent a
temperature rise in the unit. Never cover the ventilation holes of the outer frame.
. Never install the unit near a heat source because the
environmental temperature during operation should be 5 dC to 40 dC.
1-2. Power Supply
1-2-1. Power Switch for Service
(Control panel)
w
The power switches for service of the control panels are placed only in the unit. When installing the unit, incorporate a readily accessible disconnect device in the fixed wiring, so that the operator/ engineer power in case a fault should occur.
1-2-2. Power Specifications
Power requirements : 100 to 240 V AC ±10%
50/60 Hz
Current consumption
DVS-7000A : 7 to 3.5 A BKDS-7011/7012 : 1.0 A (max.)
7021/7022/7023 7011R 7021R/7022R/7023R 7011LR 7021LR/7022LR/7023LR
m
As the inrush current at turn-on is the maximum 35 A, the capacity of the AC power must be commensurate in it with the inrush current of the maximum 35 A for the processor and the control panel respectively. If the capacity of the AC power is not the adequately large, the breaker of the AC power at the supply side will operate or the unit will abnormal operate.
1-2
DVS-7000AE IM
1-3. Connectors
1-3. Connectors
When connecting cables to various connectors on the rear panel at the time of installing, connecting or servicing, connect the following connectors or their equivalents.
1. DVS-7000A
Connector function name Connector parts No. and on rear panel name of cable
PANEL 1 D-sub 9-pin, Male DME 1 to 4 Connector 9-pin, Male SERIAL TALLY 1-560-651-00
(*1)
DSK Junction Shell 9-pin TERMINAL 1-561-749-00 EDITOR A/REMOTE 1 EDITOR A/REMOTE 2 PANEL 2/REMOTE 3
GPI D-sub 25-pin, Male
Connector 25-pin, Male
1-560-904-11
(*1)
Junction Shell 25-pin
1-563-377-11
PRIMARY INPUTS 1 to 36 BNC Coaxial Connector Plug DIRECT INPUT CRK INPUTS 1 to 4 REF INPUT REF OUTPUT AUX BUS OUTPUTS 1 to 13 ME-1 to 3 OUTPUTS PGM OUTPUTS 1 to 4 CLEAN OUTPUT PST OUTPUT EDIT PVW OUTPUT MATRIX
(*3)
AC IN Main Power Supply Cable
(For the details of the cable, refer to Section 1-2-3.)
2. BKDS Control Panel (BKDS-70xx/70xxR/70xxLR)
Connector function name Connector parts No. and on rear panel name of cable
SWITCHER D-sub 9-pin, Male DSK Connector 9-pin,Male DME 1-560-651-00
(*1)
TERMINAL 1 to 2 Junction Shell 9-pin REMOTE 1 to 5 1-561-749-00
GPI D-sub 25-pin, Male
Connector 25-pin, Male
1-560-904-11
(*1)
Junction Shell 25-pin
1-563-377-11
AUX PANEL BVS Cable
(*2)
DISPLAY PANEL 1-574-993-11 OPTION PANEL
AC IN Main Power Supply Cable
(For the details of the cable, refer to Section 1-2-3.)
(*1) : The following solderless contact must be used for the plug.
AWG #18 to #22:1-566-493-00 AWG #22 to #24:1-564-774-00 AWG #24 to #30:1-564-775-00
(*2) : The BVS cables are supplied with the models in the list below.
(*3) : Use the 9-pin BNC conversion cable supplied with DVS-7000A.
Model name DISPLAY AUX BUS OPTION TOTAL
PANEL PANEL PANEL
BKDS-701x 1 1 BKDS-701xR/ 1 1 2
701xLR BKDS-702x 1 1 2 BKDS-702xR/
702xLR 1 1 1 3
DVS-7000AE IM
1-3
1-4. Input and Output Signals of Connectors
1-4. Input and Output Signals of Connectors
The input and output signals of the connectors on the rear panel are specified in the following table. And refer to the following illustration for the pin positions of the connectors.
1-4-1. DVS-7000A
EXT VIEW
1
13
14
25
[D-SUB 25 PIN • FEMALE]
Rear panel
[D-SUB 9 PIN • FEMALE]
EXT VIEW
1
5
69
GPI
TERMINAL
DSK
MATRIX
SERIAL TALLY
DME 2
DME 4
PANEL 1
DME 1
DME 3
PANEL 2
/REMOTE 3
EDITOR B
/REMOTE 2
EDITOR A
/REMOTE 1
m
(*1) <CONTROLLER> : Controlling device (*2) <DEVICE> : Controlled device
PANEL 1 : RS-422A (D-sub 9-pin.Female) <DEVICE>
(*2)
from Control panel BKDS-7011/7012/7021/ 7022/7023 etc.
Pin No. Signal Name Function
1 GND Frame ground 2 CON TX-A Transmitted data (_) 3 CON RX-B Received data (+) 4 GND Common ground 5 VD-B Transmited VD signal (+) 6 GND Common ground 7 CON TX-B Transmitted data (+) 8 CON RX-A Received data (_) 9 VD-A Transmited VD signal (_)
PANEL 2/REMOTE 3 : RS-422A(D-sub 9-pin.Female) <DEVICE>
(*2)
from Control panel
(*3)
Pin No. Signal Name Function
1 GND Frame ground 2 CON TX-A Transmitted data (_) 3 CON RX-B Received data (+) 4 GND Common ground 5 VD-B Transmited VD signal (+) 6 GND Common ground 7 CON TX-B Transmitted data (+) 8 CON RX-A Received data (_) 9 VD-A Transmited VD signal (_)
(*3) : Control Panel BKDS-2010 etc. (PANEL 2)
Keyer Remote Panel BKDS-7060 etc. (REMOTE 3)
1-4
DVS-7000AE IM
1-4. Input and Output Signals of Connectors
SERIAL TALLY : RS-422A (D-sub 9-pin.Female) n
For the SERIAL TALLY connector, refer to the Protocol Manual of DVS-8000 Series.
Pin No. Signal Name Function
1 FG Frame ground 2 SERIAL TALLY RX-A Received data (_) 3 SERIAL TALLY TX-B Transmitted data (+) 4 GND Common ground 5 __ 6 GND Common ground 7 SERIAL TALLY RX-B Received data (+) 8 SERIAL TALLY TX-A Transmitted data (_) 9 FG Frame Ground
DME 1 to 4 : RS-422A (D-sub 9-pin.Female) <DEVICE>from Digital multi effects DME-3000/5000
etc.
Pin No. Signal Name Function
1 FG Frame ground 2 DME 1 to 4 TX-A Transmitted data (_) 3 DME 1 to 4 RX-B Received data (+) 4 GND Common ground 5 __ 6 GND Common ground 7 DME 1 to 4 TX-B Transmitted data (+) 8 DME 1 to 4 RX-A Received data (_) 9 FG Frame Ground
DSK : RS-422A (D-sub 9-pin.Female) <DEVICE>
(*2)
from DMK-7000
Pin No. Signal Name Function
1 FG Frame ground 2 DSK TX-A Transmitted data (_) 3 DSK RX-B Received data (+) 4 GND Common ground from 5 __ 6 GND Common ground 7 DSK TX-B Transmitted data (+) 8 DSK RX-A Received data (_) 9 FG Frame Ground
MATRIX
(*4)
: (D-sub 9-pin.Female)
<DEVICE>
(*1)
to Routing switcher
Pin No. Signal Name Function
1 FG Frame ground 2 GND Ground 3 DATA Data 4 GND Ground 5 __ 6 GND Ground 7 GND Ground 8 GND Ground 9 FG Frame Ground
(*4) : If connecting Sony’s Routing Switcher DVS-V6464B, use the 9-pin
BNC conversion cable supplied with DVS-7000A.
EDITOR A/REMOTE 1 : RS-422A (D-sub 9-pin.Female) <DEVICE>
(*2)
from Editor
(*5)
Pin No. Signal Name Function
1 FG Frame ground 2 EDT A TX-A Transmitted data (_) 3 EDT A RX-B Received data (+) 4 GND Common ground 5 __ 6 GND Common ground 7 EDT A TX-B Transmitted data (+) 8 EDT A RX-A Received data (_) 9 FG Frame Ground
(*5) : Editing control Unit BVE-9100 etc. (EDITOR A)
Digital Multi Effects DME-3000/5000 etc. (REMOTE 1)
EDITOR B/REMOTE 2 : RS-422A (D-sub 9-pin.Female) <DEVICE>
(*2)
from Editor
(*6)
Pin No. Signal Name Function
1 FG Frame ground 2 EDT B TX-A Transmitted data (_) 3 EDT B RX-B Received data (+) 4 GND Common ground 5 __ 6 GND Common ground 7 EDT B TX-B Transmitted data (+) 8 EDT B RX-A Received data (_) 9 FG Frame Ground
(*6) : Editing control Unit BVE-9100 etc. (EDITOR B)
Digital Multi Effects DME-3000/5000 etc. (REMOTE 2)
DVS-7000AE IM
1-5
GPI : (D-sub 25-pin.Female) INPUT x 8, TTL OUTPUT x 4, relay contact 30 V 0.1 A (resistance load) OUTPUT x 4, open collector 30 V rated voltage GPI timing : Refer to User’s Guide
Pin No. Signal Name Function
1 GND Ground 2 GND Ground 3 GPI IN 2 4 GPI IN 4
General-purpose input
5 GPI IN 6 6 GPI IN 8 7 GPI OUT 1B 8 GPI OUT 2B
General-purpose relay output (B)
(*8)
9 GPI OUT 3B 10 GPI OUT 4B 11 GPI OUT 6
General-purpose open collector output
(*9)
12 GPI OUT 8 13 GPI OUT COM Ground for open collector output 14 GND Ground 15 GPI IN 1 16 GPI IN 3
General-purpose input
17 GPI IN 5 18 GPI IN 7 19 GPI OUT 1A 20 GPI OUT 2A
General-purpose relay output (A)
(*8)
21 GPI OUT 3A 22 GPI OUT 4A 23 GPI OUT 5
General-purpose open collector output
(*9)
24 GPI OUT 7 25 GPI OUT COM Ground for open collector output
n
A and B of same number constitute a pair of relay contacts.
TERMINAL : RS-232C (D-sub 9-pin.Female)
to Terminal
Pin No. Signal Name Function
1 DCD Data Carrier detect
(*7)
2 RXD Received data 3 TXD Transmitted data 4 DTR Data terminal ready
(*7)
5 GND Ground 6 DSR Data set ready
(*7)
7 RTS Request to send 8 CTS Clear to send 9 __
(*7) : Pins 1, 4 and 6 are short-circuited each other on the CN-1146 board.
1-4. Input and Output Signals of Connectors
(*8) : <Relay>
GPI OUT x B
GPI OUT 5-8
GPI OUT COM
(*9) : <Open collector output>
x;1-4
+V
GPI OUT x A
1-6
DVS-7000AE IM
EXT VIEW
1
13
14
25
1
13
14
25
1
13
14
25
[D-SUB 25 PIN • FEMALE]
Rear panel
GPI SWITCHER DSK DME TERMINAL1 TERMINAL2
AUX PANEL
OPTION PANEL REMOTE1 REMOTE2 REMOTE3 REMOTE4 REMOTE5
DISPLAY PANEL
[D-SUB 9 PIN • FEMALE]
EXT VIEW
1
5
69
1
5
69
1
5
69
1
5
69
1
5
69
1
5
69
1
13
14
25
1
13
14
25
1
5
69
1
5
69
1
5
69
1
5
69
1
5
69
1-4-2. Control Panel
m (*1) <CONTROLLER> : Controlling device
1. Main Panel SWITCHER : RS-422A (D-sub 9-pin.Female)
<CONTROLLER>
(*1)
to Processor DVS-7000A
Pin No. Signal Name Function
1 FG Frame ground 2 RX-A Received data (_) 3 TX-B Transmitted data (+) 4 GND Common ground 5 FIELD (+) Field signal input (+) 6 GND Common ground 7 RX-B Received data (+) 8 TX-A Transmitted data (_) 9 FIELD (_) Field signal input (_)
DSK : RS-422A (D-sub 9-pin.Female) <CONTROLLER>
(*1)
to DMK-7000
Pin No. Signal Name Function
1 FG Frame ground 2 RX-A Received data (_) 3 TX-B Transmitted data (+) 4 GND Common ground 5 __ 6 GND Common ground 7 RX-B Received data (+) 8 TX-A Transmitted data (_) 9 __
1-4. Input and Output Signals of Connectors
DME : RS-422A (D-sub 9-pin.Female) <CONTROLLER>
(*1)
to Digital multi effects DME-3000/ 7000 etc.
Pin No. Signal Name Function
1 FG Frame ground 2 RX-A Received data (_) 3 TX-B Transmitted data (+) 4 GND Common ground 5 __ 6 GND Common ground 7 RX-B Received data (+) 8 TX-A Transmitted data (_) 9 __
DVS-7000AE IM
1-7
REMOTE 1 : RS-422A (D-sub 9-pin.Female) <CONTROLLER>
(*1)
to External Device
Pin No. Signal Name Function
1 FG Frame ground 2 RX-A Received data (_) 3 TX-B Transmitted data (+) 4 GND Common ground 5 __ 6 GND Common ground 7 RX-B Received data (+) 8 TX-A Transmitted data (_) 9 __
REMOTE 2 to 5
(*2)
: RS-422A (D-sub 9-pin.Female)
<CONTROLLER>
(*1)
to External Device
Pin No. Signal Name Function
1 FG Frame ground 2 RX-A Received data (_) 3 TX-B Transmitted data (+) 4 GND Common ground 5 __ 6 GND Common ground 7 RX-B Received data (+) 8 TX-A Transmitted data (_) 9 __
(*2) : BKDS-7001(Option:IF-523 board) is in need of using the REMOTE
from 1 to 4.
TERMINAL 1, 2 : RS-232C (D-sub 9-pin.Female)
to Terminal
Pin No. Signal Name Function
1 DCD Data carrier detect
(*3)
2 RXD Received data 3 TXD Transmitted data 4 DTR Data terminal ready
(*3)
5 GND Ground 6 DSR Data set ready
(*3)
7 RTS Request to send
(*4)
8 CTS Clear to send
(*4)
9 __
(*3) : Pins 1, 4 and 6 are short-circuited each other on the CN-1143 board. (*4) : Pins 7 and 8 are short-circuitede each other on the CN-1143 board.
DISPLAY PANEL : (D-sub 25-pin.Female)
to Display panel
Pin No. Signal Name Function
1 GND Ground 2 +12 V Power supply +12 V 3 SCLK Serial clock for switch read and
LED light 4 GND Ground 5 WDT LED light data 6 IWLD Control signal for switch read and
LED light 7 GND Ground 8 ELCK EL display indicate clock 9 EL DATA 0 EL display indicate data 10 GND Ground 11 ELVD EL display vertical sync signal 12 GND Ground 13 GND Ground 14 +12 V Power supply +12 V 15 +12 V Power supply +12 V 16 BLANK LED light disable signal 17 GND Ground 18 SEQ Control signal for switch read and
LED light 19 RDT Switch read data 20 GND Ground 21 ELHD EL display horizontal sync signal 22 EL DATA 1 EL display indicate data 1 23 +12 V Power supply +12 V 24 +12 V Power supply +12 V 25 GND Ground
1-4. Input and Output Signals of Connectors
1-8
DVS-7000AE IM
GPI : (D-sub 25-pin.Female) INPUT x 8, TTL OUTPUT x 4, relay contact 30 V 0.1 A (resistance load) OUTPUT x 4, open collector 30 V rated voltage GPI timing : Refer to User’s Guide
Pin No. Signal Name Function
1 GND Ground 2 GND Ground 3 GPI IN 2 4 GPI IN 4
General-purpose input
5 GPI IN 6 6 GPI IN 8 7 GPI OUT 1B 8 GPI OUT 2B
General-purpose relay output (B)
(*5)
9 GPI OUT 3B 10 GPI OUT 4B 11 GPI OUT 6
General-purpose open collector output
(*6)
12 GPI OUT 8 13 GND Ground 14 GND Ground 15 GPI IN 1 16 GPI IN 3
General-purpose input
17 GPI IN 5 18 GPI IN 7 19 GPI OUT 1A 20 GPI OUT 2A
General-purpose relay output (A)
(*5)
21 GPI OUT 3A 22 GPI OUT 4A 23 GPI OUT 5
General-purpose open collector output
(*6)
24 GPI OUT 7 25 GND Ground
n
A and B of same number constitute a pair of relay contacts.
AUX PANEL : (D-sub 25-pin.Female)
to AUX panel
Pin No. Signal Name Function
1 GND Ground 2 +12 V Power supply +12 V 3 SCLK Serial clock for switch read and
LED light 4 GND Ground 5 WDT LED light data 6 IWLD Control signal for switch read and
LED light 7 GND Ground 8 TCLK Serial clock for character display 9 TWDT Indicate data for character display 10 GND Ground 11 TBLANK Disable signal for character display 12 GND Ground 13 GND Ground 14 +12 V Power supply +12 V 15 +12 V Power supply +12 V 16 BLANK LED light disable signal 17 GND Ground 18 SEQ Control signal for switch read and
LED light 19 RDT Switch read data 20 GND Ground 21 TSEQ Control signal for character display 22 TQCLK Control signal for character display 23 +12 V Power supply +12 V 24 +12 V Power supply +12 V 25 GND Ground
1-4. Input and Output Signals of Connectors
(*5) : <Relay>
GPI OUT x B
GPI OUT 5-8
GPI OUT COM
(*6) : <Open collector output>
x;1-4
+V
GPI OUT x A
DVS-7000AE IM
1-9
OPTION PANEL : (D-sub 25-pin.Female)
to Adaptor box (BKDS-7075)
Pin No. Signal Name Function
1 GND Ground 2 +12 V Power supply +12 V 3 SCLK Serial clock for switch read and
LED light 4 GND Ground 5 WDT LED light data 6 IWLD Control signal for switch read and
LED light 7 GND Ground 8 TCLK Serial clock for character display 9 TWDT Indicate data for character display 10 GND Ground 11 TBLANK Disable signal for character display 12 GND Ground 13 GND Ground 14 +12 V Power supply +12 V 15 +12 V Power supply +12 V 16 BLANK LED light disable signal 17 GND Ground 18 SEQ Control signal for switch read and
LED light 19 RDT Switch read data 20 GND Ground 21 TSEQ Control signal for character display 22 TQCLK Control signal for character display 23 +12 V Power supply +12 V 24 +12 V Power supply +12 V 25 GND Ground
n
This port is used for special-use-ready. Only when connecting the control harness onto the CN8 of the connec­tor on the CN-1143 board, this port is enable. 
1-4. Input and Output Signals of Connectors
2. Display Panel
_ : (D-sub 25-pin.Female)
from Main panel
Pin No. Signal Name Function
1 GND Ground 2 +12 V Power supply +12 V 3 SCLK Serial colck for switch read and
LED light 4 GND Ground 5 WDT LED light data 6 IWLD Control signal for switch read and
LED light 7 GND Ground 8 ELCK LE display indicate clock 9 EL DATA 0 EL display indicate data 0 10 GND Ground 11 ELVD EL display vertical sync signal 12 GND Ground 13 GND Ground 14 +12 V Power supply +12 V 15 +12 V Power supply +12 V 16 BLANK LED light disable signal 17 GND Ground 18 SEQ Control signal for switch read and
LED light 19 RDT Switch read data 20 GND Ground 21 ELHD EL display horizontal sync signal 22 EL DATA 1 EL display indicate data 1 23 +12 V Power supply +12 V 24 +12 V Power supply +12 V 25 GND Ground
1-10
DVS-7000AE IM
1-4. Input and Output Signals of Connectors
3. AUX Bus Panel AUX PANEL :(D-sub 25-pin.Female)
from Main panel
Pin No. Signal Name Function
1 GND Ground 2 +12 V Power supply +12 V 3 SCLK Serial colck for switch read and
LED light 4 GND Ground 5 WDT LED light data 6 IWLD Control signal for switch read and
LED light 7 GND Ground 8 TCLK Serial clock for character display 9 TWDT Indicate data for character display 10 GND Ground 11 TBLANK Disable signal for character display 12 GND Ground 13 GND Ground 14 +12 V Power supply +12 V 15 +12 V Power supply +12 V 16 BLANK LED light disable signal 17 GND Ground 18 SEQ Control signal for switch read and
LED light 19 RDT Switch read data 20 GND Ground 21 TSEQ Control signal for character display 22 TQCLK Control signal for character display 23 +12 V Power supply +12 V 24 +12 V Power supply +12 V 25 GND Ground
DVS-7000AE IM
1-11
1-5. Examples of System Connection
1. D1 LIVE SWITCHER SYSTEM
1-5. Example of System Connection
SW'ER MAIN
MAIN PANEL
SUB PANEL
SG
DCU
CCU
DVR-2000
CG
PC
TALLY
1234567891011121314151617181920212223242526272829303132333435
36
D1 LIVE SW'ER
3ME+PP
SUPER
V/K
SOURCE
DCU
REC
SOURCE
DME1
DME2
DME3
DME4
DME5
DME6
DSK
DVW-500
BVW-75D
BVW-75
YUV
VKYUV
INTERFACE
UNIT
BKDS-7700
DVS-7000A
DMK-7000
DME-7000
DME-7000
DME-7000
DME-7000
DME-7000
DME-7000
ME1 PGM
ME2 PGM
ME3 PGM
PGM1
PGM2
PGM3
PGM4
PST
DSK
AUX1
AUX2
DME1
AUX3
AUX4
DME2
AUX5
AUX6
DME3
AUX7
AUX8
DME4
AUX9
AUX10
AUX11
AUX12
AUX13
EDIT PVW
DIRECT IN
TALLY
SERIAL
GPI
TERMINAL
MATRIX
CRK IN
x2
x2
INPUTS
COMPONENT
ANALOG
INPUTS
COMPONENT
ANALOG
Y1U1V1S1Y2U2V2S2Y3U3V3
S3
x12
DME V/K
INPUTS
DIGITAL
x4
SUPER V/K
x4
VTR
INPUTS
DIGITAL
x12
CAMERA
INPUTS
DIGITAL
REF OUT
REF IN
1
PANEL
REMOTE3
REMOTE2
DME
DSK
SW'ER
CONTROL
OUT1
BKDS-70xx/70xxR/70xxLR
BKDS-7060
BKDS-2010
PANEL B DSK1
PGM
PVW
DSK2
PGM
PVW
DSK3
PGM
PVW
DSK4
PGMSW ER
PST
PGM
PANEL A
TALLY/GP1
REF OUT
REF IN
OUT
EDITOR
IN
K4V4K3V3K2V2K1V1
MONITOR
ME1
ME2
ME3
PVW
DSK
DSK
PGM
VE
WFM
SW'ER
K
V
VKVKZ
SW'ER PANEL
DME PANEL
VKZ
DME PANEL
SW'ER PANEL
KV
V
K
SW'ER
DME PANEL
SW'ER PANEL
SW'ER
K
V
VKVKZ
VKZ
VKZ
VKZ
DME PANEL
SW'ER PANEL
SW'ER
K
V
VK
DME PANEL
SW'ER PANEL
SW'ER
K
V
VKVKZ
DME PANEL
SW'ER PANEL
VKZ
SW'ER
K
V
VK
PVW
EDITOR B
/REMOTE 2
EDIDOR A
/REMOTE 1
PANEL 2
/REMOTE 3
KEYER REMOTE
CONTROL PANEL
Y4/V4/U4/S4
CONTROL
OUT2
1-12
DVS-7000AE IM
2. D2 LIVE SWITCHER SYSTEM
1-5. Example of System Connection
MAIN PANEL
SUB PANEL
V
K
SW'ER
VKZ
DME PANEL
SW'ER PANEL
VK
SG
CCU
CG
BVW75
PC
123456789101112131415161718192021222324252627282930313233343536Y1U1V1S1Y2U2V2S2Y3U3V3
S3
3ME+PP
MONITOR
SUPER
V/K
SOURCE
REC
SOURCE
DME1
DME2
DME3
DME4
DME5
DME6
CCU
CCU
DVR-20
D2 LIVE SW'ER
DSK
YUV
DVR-28
BVW-D265
VKYUV
V1 K1 V2 K2 V3 K3 V4 K4
DVS-7000A
DMK-7000
DME-7000
DME-7000
DME-7000
DME-7000
DME-7000
DME-7000
CONTROL
OUT1
BKDS-7060
BKDS-2010
SW'ER
SW'ER
DSK
REMOTE3
REMOTE2
DME
ME1 PGM
ME2 PGM
ME3 PGM
PGM1
PGM2
PGM3
PGM4
PST
DSK
AUX1
AUX2
DME1
AUX3
AUX4
DME2
AUX5
AUX6
DME3
AUX8
AUX7
DME4
AUX9
AUX10
AUX11
AUX12
AUX13
EDIT PVW
DIRECT IN
GPI
SERIAL
TALLY
TERMINAL
MATRIX
Y4/U4/V4/S4
x2
CRK IN
x2
x12
DME V/K
INPUTS
COMPONENT
ANALOG
INPUTS
COMPONENT
ANALOG
INPUTS
DIGITAL
INPUTS
DIGITAL
x4
SUPER V/K
x4
VTR
REF OUT
REF IN
1
PANEL
ANALOG
COMPOSITE
INPUTS
CAMERA
x12
REF IN
REF OUT
TALLY/GDI
PANEL A
PGM
PST
SW'ER
OUT
EDITOR
IN
DSK1
PGM
PVW
DSK2
PGM
PVW
DSK3
PGM
PVW
DSK4
PGM
PANEL B
DME PANEL
SW'ER PANEL
SW'ER
K
V
VKVKZ
DME PANEL
SW'ER PANEL
KZKVV
V
K
SW'ER
KZV
SW'ER
K
V
VK
SW'ER PANEL
DME PANEL
SW'ER
K
V
VKVKZ
SW'ER PANEL
DME PANEL
KZV
VKZ
KZV
SW'ER
K
V
VK
SW'ER PANEL
DME PANEL
PVW
ME1
ME2
ME3
PVW
DSK
DSK
PGM
VE
WFM
EDITOR A
EDITOR B
/REMOTE 1
/REMOTE 2
PANEL 2
/REMOTE 3
CONTROL PANEL
KEYER REMOTE
CONTROL
OUT2
BKDS-70xx/70xxR/70xxLR
TALLY
INTERFACE
UNIT
BKDS-7700
DVS-7000AE IM
2-1
Section 2
Installation of DVS-7000A
2-1. External Dimensions
A B
482
424
465
368.3
443 (10 UNIT)
23.5
40 40
37.35
13
221.5
111.1
28.5
250.8
403.2
8-M4
37.7
5.5
2929
13
13
477.8 452
Unit : mm
88
2-2
DVS-7000AE IM
2-2. Rack Mounting
2-2. Rack Mounting
DVS-7000A can be mounted in a 19-inch standard rack. Be sure to use the optional rack mount rail RMM-18DV.
Required Parts
. Rack mount rail (RMM-18DV) . Screw for plate nut (long) installing (B4 x 8) : 8pcs . Screw for rack mounting (RK5 x 16) : 4pcs . Ornamental washer for rack mounting : 4pcs
(Sony part number : 2-297-913-01)
c
(1) If DVS-7000A is mounted in the 19-inch standard rack, it is recommended to install a ventilation fan
to prevent a temperature rise in the rack. Make sure that all the units in the rack should be operated within the temperature range of 10 dC to 35 dC.
(2) Be sure to use the recommended rail when rack mounting. The unit cannot be installed completely to
a rack by rack angles alone.
(3) It is recommended to fix the rack to the floor with bolts. When the unit is pulled out from the rack,
this will prevent its fall.
(4) An installation manual is supplied with the rack mount rail RMM-18DV. However follow the
instructions in this manual. Because the rack mounting procedures of DVS-7000A differ somewhat from the procedures explained in RMM-18DV installation manual.
(5) Be sure to mount in the rack with two-person or more.
DVS-7000AE IM
2-3
Brackets
Plate nut (Long)
Outer member1
B4 x 8
B4 x 8
B4 x 8
B4 x 8
Outer member stopper (Used for fixing the outer member2.)
(Fig. 3)
Plate nut (Long)
Outer member2
2-2. Rack Mounting
Procedures
(1) Pull out the inner member while pressing the stopper of the rack mount rail RMM-18DV. (Fig. 1)
(2) Secure the inner member to the unit by the sixteen screws (B4 x 8) supplied with DVS-7000A.
Remove the feet of the unit as required. (Fig. 2)
(3) Secure the bracket to the outer member 1 by the preparated eight screws (B4 x 8). (Fig. 3)
To see the screw hole of the outer member 1, move the outer member 1 back-and-forth.
DVS-7000A
Feet
B4 x 8
B4 x 8
Inner member
Inner member
Inner member
Stopper
Outer member1
(Fig. 2)(Fig. 1)
2-4
DVS-7000AE IM
Bracket
Rack
Outer member
C4 x 12
W4
44.45
12.7
C4 x 12
W4
Outer member1
Bracket
Rack
TOP VIEW
Spec 50
_0
Plate nut (Short)
+5
(Fig. 4)
Plate nut (Short)
2-2. Rack Mounting
(4) Temporarily secure the bracket to the outer member assembly 1 to both sides of the rack by the
eight screws (C4 x 12) and the eight washers (W4) supplied with RMM-18DV. Adjust the installa­tion position of the outer member to meet the specification shown in the figure. After the adjustment, tighten the screws (B4 x 8) temporarily secured in the step (3). (Fig. 4)
(5) Install the unit in the rack while releasing the stopper of the inner member. (6) After confirming that the unit can be moved smoothly, tighten the screws (C4 x 12) temporarily
secured in the step (4). (Fig. 5)
Outer member2
Stopper
Rack
DVS-7000A
Inner member
Inner member Slide bearing
. When housing the set, shift the slide bearing as illustrated.
Outer member2
(Fig. 5)
DVS-7000AE IM
2-5
221.5
443
Distance to slide rail center
Set height when mounted in rack
30
Unit : mm
Maximum moving distance
569
Handle height
2-2. Rack Mounting
(7) After installing the unit in the rack, secure the unit to the rack by the prepared four screws (RK5 x
16) and the four ornamental washers. (Fig. 6)
. When DVS-7000A is mounted in a rack, the maximum traveling distance is illustrated below.
RK5 x 16
RK5 x 16
RK5 x 16
RK5 x 16
Ornamental washer
Ornamental washer
Rack
Rack
––– TOP VIEW–––
Rack angle
DVS-7000A
Bracket
Outer member
(Fig. 6)
RK5 x 16
DVS-7000AE IM
3-1
3-1. External Dimensions
* The above figure shows the BKDS-7011.
Section 3
Installation of Control Panel
Main Panel BKDS-7011/7012
1290
15
30
1200
30
15
49
230
199 7.2
45˚
350
110 10
Unit : mm
572
532
(
40
)
(
51
)
15 51 15
400
3-2
DVS-7000AE IM
3-1. External Dimensions
Main Panel BKDS-7011R
1142
15
30
1052
30
15
49
230
199 7.2
45˚
350
110 10
Unit : mm
572
532
(
40
)
(
51
)
15 51 15
400
Loading...
+ 80 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use