Sonic Alert SBR350SS User Manual

p

p

N

The Lightning flash and
arrowhead within the
triangle is a warning sign
alerting you of dangerous
voltage inside the

roduct.

CAUTION: TO
REDUCE THE RISK OF
ELECTRICAL SHOCK,
DO NOT REMOVE THE
COVER (OR BACK)
FROM THE PRODUCT.

O USER
SERVICABLE PARTS
INSIDE. REFER
SERVICING TO YOUR
SONIC ALERT
DEALER.

The exclamation mark
within the triangle is a
warning sign alerting you
of important instructions
accompanying the

roduct.

!

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT

EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

SONIC ALERT’S 1 YEAR LIMITED WARRANTY

The Sonic Boom Alarm Clock Model SBR350ss is warranted
against manufacturing defects in materials and workmanship for
one(1) year from the date of purchase. Within this period Sonic
Alert will repair or replace at our option the SBR350ss without
charge for parts and labor. Simply send the SBR350ss (postpaid)
and a copy of your sales slip as proof of purchase to:

Sonic Alert Inc., 1050 E. Maple Road, Troy MI 48083

Sonic Boom Alarm Clock

with AM / FM Radio & Bed Shaker

Model SBR350ss

Made in China

Sonic Alert 1050 East Maple Rd. Troy, MI 48083

www.SonicAlert.com

1-800-566-3210 V/TTY

OPERATION INSTRUCTIONS

IMPORTANT- Please read these instructions carefully before use and retain for future

reference. See operating instructions on back.

Warning: To prevent fire or shock hazard do not expose this appliance to rain or moisture. Before
connecting, make sure that the requirements specified on the apparatus corresponds to the available
power supply i.e. AC 110V/220-340V (50Hz/60Hz)

GENERAL DATA

Power: Consumption: 8w, 110v / 60 Hz
Radio Frequency: U.S. AM: 540-1700 KHz / FM: 88-108 MHz
UL listed transformer (Underwriters Laboratories)

Made in China

Sonic Alert 1050 East Maple Rd. Troy, MI 48083

www.SonicAlert.com 1-800-566-3210 V/TTY

NSTRUCTIONS
AM / FM RADIO ALARM CLOCK WITH BED SHAKER
MODEL SBR350SS

Features shown on diagrams above:

1) Setting Switch 7) Minute Button 13) AM / FM Band Switch

2) Dimmer Switch 8) Snooze Button 14) Backup Battery Compartment

3) Alarm Indicator 9) Alarm Off Button 15) AC Power Input

4) PM Indicator 10) Volume Control 16) Vibrator Input

5) Sleep Button 11) Function Switch 17) FM Antenna

6) Hour Button 12) Tuning Dial 18) Alarm option switch

Setting the correct time-

1) Slide the setting switch (1) to the position marked “TIME”.

2) Depress hour button (6) as necessary to advance the clock display until the hour is correct.

3) Depress minute button (7) as necessary to advance the clock display until the minute is correct.

4) Slide the setting switch (1) to the position marked “LOCK” this will prevent the clock time from
being changed.

5) Lighted dot (10) in upper left clock display indicates time is PM, no light indicates time is AM.

Setting the alarm time-

Battery Backup-

To Play Radio-

Radio Reception-

Sleep Timer Operation-

Wake To Radio-

Sleep To Radio and Wake To Radio-

Sleep To Radio and Wake Buzzer-

Shutting Off Alarm-

Snooze Operation-

Alarm-

Volume-

Bed Shaker / Vibrator- Figure B

AC-9V Power Input -

1) Simply follow the instructions mentioned under “ Setting the correct time” except that you will
have to slide switch (1) to the “AL” position.

2) Make sure the alarm time is correctly set for AM or PM lighted dot (10) indicates PM). Be sure
to release the HOUR and MIN set buttons before releasing the ALARM button.

3) Once the alarm time is set slide the setting switch (1) back to the position marked “LOCK” this
will prevent the alarm from being changed.

4) To enable the alarm function, slide the Function Switch (11) to position marked “ALARM”.
This will turn on the alarm feature. Otherwise, alarm will not go off for the alarm time set.

5) You will see a dot (3) on the left side of the LED display to show the alarm has been enabled.

To use battery backup, you can install a 9-volt alkaline battery in the back of the clock located under the
battery cover (7). Battery not included. Note the LED display will not show during power failure but the
clock will still be running and keeping proper time until the power comes back.

1) Slide the Function Switch (11) to “ON” position to turn radio “ON”.

2) Use rotary volume wheel (10) and turn to desired listening level.

3) Slide Band Switch (13) to either AM or FM.

4) Tune radio station by turning the Tuning Dial (12) to desired radio frequency.

For best reception unwind wire antenna cord to its full length (16). Make sure radio isn’t near any
electrical appliances that may cause interference.

1) You may use the sleep function to have the radio on while you go to sleep. It will automatically
shut itself off after the specified time.

2) Make sure the Function Switch (11) is NOT set to “ON” otherwise sleep function will not work
and the radio will play continuously.

3) Press sleep button (5) and radio will play for an hour. You can also set sleep timer for other
lengths of shut off time.

4) Press and hold the sleep timer button (5). It will start at 59 minutes and countdown to 1 minute.
Release sleep timer button (5) once the desired sleep time is chosen.

Set alarm wakeup time by following the procedure under “Setting the Correct Time” Slide the
function switch (11) to position marked “AUTO”, this will turn on the radio feature at the alarm time
set. Otherwise radio will not go off for the alarm time set.

You may use the sleep function to have radio on while you go to sleep and have the radio wake you in
the morning. Follow directions under section labeled Sleep Timer Operation and Wake To Radio.

You may use the sleep function to have the radio on while you go to sleep and have the buzzer wake
you in the morning. Follow the directions under Setting the Alarm Time and Sleep Timer Operation.

Alarm can be shut off temporary for the day or permanently shut off.

1) When the alarm goes off, simply press the AL off button (9) the alarm will shut itself off for the
day and come back on the next day at the same time if alarm setting has not changed

2) To shut the alarm off permanently, slide function switch (11) to off position. Alarm will not
come on until Function Switch (11) is set to “AUTO” or “ALARM” position.

SNOOZE button (13) - press after alarm has sounded. The alarm will be turned off for 9 minutes for
extra sleep. The alarm will come back again after 9 minutes. You may repeat up to 59 minutes.

Set the alarm time you wish and slide the VIB / BUZZ / OFF (12) switch to the desired position. Set
to VIB for bed shaker and BUZZ for sound, or VIB/BUZZ for both.

To adjust the volume rotate the wheel located on back right side (5).

1) Attach the bed shaker jack to the back of clock at VIBRATOR input.

2) To turn on vibrator slide switch (12) to VIB or VIB/BUZZ position.

3) Place vibrator under mattress or pillow.

Attach the AC power supply input to the back of clock at AC-9V IN next to the VIBRATOR input,
smaller input of the two. Important do not confuse input with vibrator input.