Sonic Alert SB200ss-v3 Operation Instructions Manual

Sonic Boom Travel & Bed side Alarm Clock with Bed Shaker

Model SB200ss-v3

IMPORTANT – Please read these instructions carefully before use and retain for future reference. See

operating instructions on back.

– Use only the supplied or recommended Sonic Alert adaptor to connect the unit.

Warning: To prevent fire or shock hazard do not expose this appliance to rain or moi sture. Before connecting

to mains make sure that the requirements specified on the apparatus corresponds to the available
power supply i.e. AC100 –240V~.

– The ventilation should not be impeded by covering the ventilation openings with items, such as

newspaper, table cloths, curtains, etc;

– No naked flame sources, such as lighted candles, should be placed on the apparatus.

– It shall not be exposed to dripping or splashing and that no objects filled with liquids, such a s

vases, shall be placed on the apparatus.

– Do not place the product in closed bookcases or racks without proper ventilation.

OPERATION INSTRUCTIONS

IMPORTANT- please read these instructions carefully before use and retain for future reference.

FEATURES

1. Alarm 1 indicator (AL1) 9. Snooze Button/ Snooze
Duration Adjustment/
Dimmer Control

2. Alarm Mode Switch 10. Tone Control

3. PM indicator 11. Alarm Selector

4. Alarm Off Button 12. Alarm 2 indicator (AL2)

5. Alarm Set Button / Alarm

Duration Adjustment

13. Volume Control

6. Fast Button/ 12 /24 hour

Selector

14. DC 9V input

7. Slow Button 15 . Vibrator input

8. Time Set Button 16. Battery Compartment

Test Mode:

1) Press and hold the Snooze (9) and T ime Set button (8) for 3 seconds to enter th e Test Mode. The display
will show "7ES7" to indicate it is in TEST Mode.

2) If within 1 minute no button is pressed, then it will exit the Test Mode and return back to the Time Mode.

3) Press any button within 1 minute (except the Snooze & Time button, which has no effect), it will exit the
Test Mode immediately.

4) While in Test Mode, sliding the Function Switch will demonstrate the different functions of the clock:
a) Function Switch at OFF, it will have a continuous "Vee" sound to indicate it is in the Test Mode.
b) Function Switch at BUZZ, it will demonstrate the buzzer sound.
c) Function Switch at VIB, it will demonstrate the vibrator.
d) Function Switch at VIB & BUZZ, it will demonstrate the buzzer sound & the vibrator.

5) Af ter finish with the Test Mode, press any button (except the Snooze & Time buttons, which ha s no ef fect)
it will exit the Test Mode immediately.

Setting the correct time –

1) Press and hold the “TIME“ Button (8) and at the same time press the “FAST“ Button (6) or the
“SLOW“ button (7) to advance clock display until you have desired time.

2) The lighted dot (3) located in upper left corner of the clock display indicates the time is PM. For AM time,
this dot will not light up.

Setting the Alarm Time–

Setting Alarm 1

1) Slide the “ALARM SELECTOR” (11) to AL1 position, the alarm indicator “AL1” (1) will light up.

2) Press and hold the “ALARM SET ” (5) button and at the same time press the “FAST” But ton (6) or the
“SLOW” button (7) to advance clock display until you reach desired alarm setti ng.

3) Make sure alarm time is correctly set.

Setting Alarm 2

4) Once alarm AL1 has been set, slide “ALARM SELECTOR” (11) to AL2 position, the alarm indicator
“AL2“ (12) will light up.

5) Press and hold the “ALARM SET ” (5) button and at the same time press the “FAST” But ton (6) or the
“SLOW” Button (7) to advance clock display until you reach desired alarm setting.

Selecting 12 or 24 hours format

– For Europe, the clock is set to 24 hour format, while for UK the clock is set to 12 hour format.

Press and hold the Fast Button (6) for 6 seconds to enter the hour selection m ode, when the display
shows "12 H" or "24 H" release the Fast Button (6). Press and release the Fast Button (6) to toggle
between 12 or 24 hours. If no selection is made within 4 seconds, then the last displayed hour format will
be chosen and the display will return to the normal Time mode.

Alarm –

Enable Alarms:

1) To enable Alarm 1, slide the “ALARM SELECTOR” (11) to AL1 position. The alarm indicator “AL1” (1) will
light up.

2) To enable Alarm 2, slide the “ALARM SELECTOR” (11) to AL2 position, the alarm indicator “AL2” (12) will
light up.

3) To enable both alarms, slide the “ALARM SELECTOR” (11) to AL1+AL2 position, the alarm indicators

“AL1” (1) and “AL2” (12) will light up.

To Select Wake up mode

To select the wake up mode, slide the “Alarm Mode Switch” (2) to your desired position:­a) “BUZZ“ for sound b) “VIB“ for bed shaker c) “VIB/ BUZZ“ for both sound and bed shaker

NOTE: once the wake up mode is chosen, this will apply to both alarms.