Sonance 275 SE User Manual

Sonamp®Power Amplifers

275 SE Series

Specifications

Rated Power (20Hz – 20kHz) RMS: 75 Watts per channel @ 8 ohms

125 Watts per channel @ 4 ohms 135 Watts per channel @ 2.7 ohms

Bridged Power (20Hz – 20kHz) RMS: 250 Watts @ 8 ohms (275 SE only)

Midband Power (1kHz, at Clipping) RMS: 114 Watts per channel @ 8 ohms

140 Watts per channel @ 4 ohms 168 Watts per channel @ 2.7 ohms

Bridged Midband Power (1kHz) RMS: 270 Watts @ 8 ohms (275 SE only)

IHF Dynamic Power 120 Watts per channel @ 8 ohms (20ms 1kHz Tone Burst) 194 Watts per channel @ 4 ohms per IHF RS-490/3.2: 239 Watts per channel @ 2.7 ohms

IHF Dynamic Headroom +1.75 dB @ 8 ohms

+1.9 dB @ 4 ohms +2.5 dB @ 2.7 ohms

Total Harmonic Distortion (2-channel mode): 0.05% 20Hz – 20kHz @ 8 ohms

0.08% 20Hz – 20kHz @ 4 ohms

0.15% 20Hz – 20kHz @ 2.7 ohms

Total Harmonic Distortion (Bridged mode): 0.05% 20Hz – 20kHz @ 8 ohms

I.M. Distortion (SMPTE 4:1) @ 8 ohms: 0.008% @ 1 watt

0.015% @ 75 watts

Signal to Noise Ratio: 105dB below rated output

(A-weighted)

Input Sensitivity: 0.7 volts for rated output

(75 watts @8 ohms)

Input Impedance: 47k ohms, Min.

BBE Effect Level: +9dB/+6dB/OFF

Power Requirement (120V versions): 120 VAC, 50/60Hz

Power Requirement (230V versions): 230VAC 50/60Hz

Power Consumption (all versions): 675 watts (@ 4 ohms, full power)

Heat Output (at Full Power): 1330 BTU

Dimensions (W x H x D): 16¾" x 3

/8" x 15¼"

(425mm x 98mm x 387mm)

Dimensions (W x H x D): 19" x 3½" x 15¼" Rack-Mount Version (483mm x 89mm x 387mm)

Shipping Weight: 24 lbs (10.9 kg)

Sonamp®275 SE Series Amplifiers

The new Sonamp® 275 SE (Sound Enhancement) amplifiers include a factory-installed Sonance BBE® Sound Enhancement SAT (Smart Amplifier Technology) module. The BBE process improves presence and detail of speakers, especially at lower listening volumes. This makes it particularly effective at improving the sound quality of distributed audio systems playing background music. BBE restores clarity and definition (or focus) to spoken voices, making paging systems easier to understand without having to run them at high volumes. The BBE process is so effective that it can even compensate for inferior sound from poor-quality source material or compressed sources like MP3, etc. In addition to manual control, the BBE effect can also be triggered on/off and the effect amount changed (+6dB or +9dB) by an external control voltage.

Features:

• Factory-installed BBE SAT module in all versions

• High-current amplifier topology that can operate at 2.66 ohms

• Auto-resetting thermal protection shutoff; inrush currentlimiting circuit; active current limit, short-circuit and speaker protection

• Defeatable auto-on signal sensing with adjustable turn-on delay (2, 4, 6, 8, 12 seconds)

• Bridge/mono switch (not available on 275X3 SE)

• Defeatable high-pass filter to protect in-wall volume controls

• Tamper-resistant, recessed input level and auto-on sensitivity controls; recessed power switch prevents accidental turn-off

• Signal present LEDs and protect/clipping LEDs for easy level setup

• 275X3 SE has 3 built-in speaker switches and connections for 3 pairs of speakers.

• Available versions: 275 SE / 275 SE RMF,

275X3 SE / 275X3 SE RMF, 275 SE (230V) / 275 SE RMF (230V)

www.sonance.com

212 Avenida Fabricante San Clemente, CA 92672-7531 USA (800) 582-7777 or (949) 492-7777 FAX: (949) 361-5151 Technical Support: (800) 582-0772

“BBE” and its designs are the registered trademarks of BBE Sound, Inc..

Due to continuous product improvement,all specifications are subject to change without notice. For the latest Sonance product specification informaton visit our website: www.sonance.com 06/07