SOMFY LT RTS CMO Setting Instructions Manual

LT RTS CMO MOTOR

Programming and Limit Setting Instructions

Description

The LT RTS CMO is designed for rolling blinds, awnings, and shutters.
The LT RTS CMO must be programmed with the Inteo family of transmitters.
The LT RTS CMO motors are compatible with a SOLIRIS and EOLIS RTS SENSORS.

Important Installation Tips

A.

For initial programming provide power only to the motor being programmed.

B.

All motor feedback (previously audible "beeping") is now replaced by a visual jog. A jog is a short Up & Down movement of the motor

(0.5 second turn of the motor in each direction).

C. The LT RTS CMO motor in Factory Mode will not respond to any transmitter (as it did previously with RTS Motors) until a transmitter is

assigned to communicate with the motor's receiver. To assign a transmitter press its UP & DOWN buttons simultaneously until the motor jogs.

D. Before pressing the programming button on the transmitter, verify the motor directions (if DOWN on the transmitter corresponds to DOWN on

the end-product) and set the end limits of the motor. Refer to section 4.3 of this instruction.

E. The motor is packaged in "FACTORY MODE", and will remain in this mode until the programming button on the transmitter is pressed, thus

putting it into "USER MODE". ROTATION DIRECTION CAN ONLY BE MODIFIED IN "FACTORY MODE".

F. A double power cut cannot be achieved if the motor is still in FACTORY or INSTALLER Mode. First program a transmitter into the memory

of the motor.

G.

WARNING: For the EOLIS/SOLIRIS RTS SENSOR to function properly, the transmitter which is memorized into the motor's receiver must be
configured correctly. The DOWN button MUST correspond to DOWN on the end-product. In the case of an awning, it will open or extend the awning.
If the UP button extends the awning, the wind sensor will also extend the awning during windy conditions. THIS IS DANGEROUS! Damage and injury
could occur. Do not proceed until proper operation of the transmitter is verified.

Power Supply

1

A. All wiring must conform to NEC (National Electrical Code) and local codes.

120 VAC / 60 Hz

B. The LT RTS CMO motors can be wired in PARALLEL.

A means of disconnecting the power at each motor independently should
be provided.

C. Power only needs to be supplied to the motor. The receiver is completely

enclosed inside the motor tube.

D. The antenna is internal to the motor.

E. SOMFY Reserves the right to void the motor warranty if wiring

recommendations are not followed.

Transmitters

2

Pictured below are all compatible controls

Motor's memory capacity with Telis, Decora RTS, Telis Soliris: maximum of 12 transmitters
plus an additional 3 RTS sensors.

The Master Channel on a 4 channel transmitter can be used as an additional individual
channel for a total of 5 channels, without the option of master control of all motors
Range: Up to 65 feet from the motor

SOLIRIS SENSOR RTS

EOLIS SENSOR RTS

SIDE

MOTOR WIRING

COLOR CODE

120 VAC CODE

BLACK
WHITE
GREEN

HOT
NEUTRAL
GROUND

TELIS 1 RTS

1 CHANNEL

4.7in/120mm

1.8in/45mm

BLACK

WHITE

GROUND

GREEN

4 INDIVIDUAL CHANNELS

& 1 MASTER CHANNEL

UP

STOP

DOWN

CHANNEL

INDICATOR

LED

HOT

NEUTRAL

TELIS 4 RTS

SIDE

0.7in mm/17

60 Hz

120 VAC

CHANNEL

SELECTOR

BACK

-

-

+

+

PROGRAMMING

BUTTON

DECORA RTS 1

SWITCH

DECORA RTS 4

SWITCH

PROGRAMMING

BUTTON

TELIS 1 RTS

TRANSMITTER

TELIS 4 RTS

TRANSMITTER

TELIS SOLIRIS RTS

TRANSMITTER

PROGRAMMING

BUTTON

HOOD

Installation Requirements

3

If the installation is made up of several RTS motors, only one
RTS motor must be powered during programming,
all other motors must be disconnected. This will avoid interferences
during the initial programming of each motor.
The mounting distance between 2 motor heads should not be less than
19 inches between RTS motor heads, to avoid possible interference.
Use only SOMFY RTS radio controls.
In order to avoid water penetration, form a "drip loop" with
the power cable and use a hood when required.
Use SOMFY accessories (adaptors, brackets, plug ends,...),
rated for the motor torque and total weight of the installation.

The motor cable should not act as a direct conduit for the
water to enter the head of the motor (form drip loops).

NOTE: SOMFY motors conform to IP44 requirements
and as such must be protected against direct weather
elements such as rain, sleet,...etc.

Factory Mode

4

This mode allows for setting of the end limitsrotation direction modification and

CONTROLLING THE LT RTS CMO MOTOR WHEN SWITCHING POWER ON FOR FIRST TIME

1) Two positions have to be set, the UP and DOWN limits. This is achieved with the mechanical CMO limit switch unit.
Provide power to the motor. Notice the motor will not respond to any transmitter until a transmitter is assigned to
communicate with the motors receiver.

A) Remove the protective cap covering the limit setting buttons on the motor head,

(replace when finished).

B) Depress fully both limit switch buttons. They will automatically lock in the down

position.

2) Assign the transmitter to communicate with the motor's receiver, push the UP and DOWN
buttons on the transmitter SIMULTANEOUSLY.

Release both buttons after the end-product jogs
briefly UP/DOWN indicating that this transmitter
can operate the motor during programming. The
LT RTS CMO motor will now operate in a
momentary fashion.

* In case of problems with FACTORY MODE, turn the power off to the motor for 2 sec. and then back on in order to reset it.

3) Check direction of operation. The DOWN button must correspond to DOWN on the end-product. In the case of an awning,
it will open or extend the awning. If the direction is wrong, change the direction as shown.

UP

STOP

DOWN

Press the stop button for
more than 5 seconds

WARNING: For the to function properly, the transmitter which is memorized into the motor's
receiver, must be configured correctly. The DOWN button MUST correspond to DOWN on the end-product. In the case of an
awning, it will open or extend the awning. If the UP button extends the awning, the wind sensor will also extend the awning
during windy conditions. Damage and injury could occur. Do not proceed until proper operation of the
transmitter is verified.

EOLIS/SOLIRIS RTS

THIS IS DANGEROUS!

SENSOR

Release the STOP button when the end-product
jogs briefly UP/DOWN indicating that the change
has been memorized in the motor. Verify that the
change took place before proceeding.