Snap-On 870015 Instruction Manual

Download

Page 1

MODEL #870015

FOR CUSTOMER SERVICE

PARA EL SERVICIO

PARA EL CONSUMIDOR

1-888-278-8092

Printed in Taiwan

SNAP-ON®IS A TRADEMARK LICENSED BY SNAP-ON®CORP., U.S.A., WHICH DOES NOT MANUFACTURE OR DISTRIBUTE THIS PRODUCT. CONSUMER INQUIRES SHOULD BE DIRECTED TO:

870015 – 18 Gauge 2" Brad Nailer _Rev 9/6/07

18 GAUGE 2" BRAD NAILER INSTRUCTION MANUAL

THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION, MAINTENANCE AND STORAGE OF THIS PRODUCT. BEFORE USE, READ CAREFULLY AND UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND PRODUCT LABELS. FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY AND/OR PROPERTY DAMAGE.

IF YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A PROBLEM WITH YOUR SNAP-ON PRODUCT,DO NOT RETURN THIS PRODUCT TO THE STORE. PLEASE CALL OUR CUSTOMER SERVICE DEPARTMENT AT 1-888-278-8092. BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION AVAILABLE: MODEL No., DATE PURCHASED AND STORE LOCATION.

Page 2

CONGRATULATIONS!

Thanks for choosing this product. Our aim is to provide you with the highest quality products, and we want you to be totally satisfied with your product and our Customer Service. If any help or advice is needed, please contact us at 1-888-278-8092. When properly cared for, this product will give you many years of satisfaction.

GENERAL SAFETY RULES

RREEAADD AANNDD FFOOLLLLOOWW AALLLL IINNSSTTRRUUCCTTIIOONNSS..

Failure to follow all instructions in this manual may result in severe personal injury or death. Keep this manual and refer to it for Safety Instructions, Operating Procedures, and Warranty.

SSAAVVEE TTHHEESSEE IINNSSTTRRUUCCTTIIOONNSS FFOORR FFUUTTUURREE RREEFFEERREENNCCEE..

RECOGNIZE SAFETY SYMBOLS, WORDS AND LABELS

The safety instructions provided in this manual are not intended to cover all possible conditions and practices that may occur when operating, maintaining and cleaning power tools.

Always use common sense and pay particular attention to all the

DDAANNGGEERR

WWAARRNNIINNGG, CCAAUUTTIIOONN

and

NNOOTTEE

statements of this manual.

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.

DDAANNGGEERR

indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WWAARRNNIINNGG

indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CCAAUUTTIIOONN

indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

TABLE OF CONTENTS

CCOONNGGRRAATTUULLAATTIIOONNSS!!

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

GENERAL SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

RECOGNIZE SAFETY SYMBOLS, WORDS AND LABELS . . . . . . . . 2-3

IMPORTANT INFORMATION ABOUT THIS MANUAL . . . . . . . . . . . 4

SAFETY WARNINGS AND PRECAUTIONS . . . . . . . . . . . . . . . . . . . 4-7

FUNCTIONAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

COMPONENT INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9

OPERATING THE BRAD NAILER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-13

SELECT TRIGGER ACTUATION MODE . . . . . . . . . . . . . . . . . . . . . . 9-11

ADJUSTING DEPTH OF NAILING . . . . . . . . . . . . . . . . . . . . . . . . . . 11-12

USING THE HOOK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

LOADING NAILS INTO THE AIR NAILER . . . . . . . . . . . . . . . . . . . . 12

USING THE NO-MAR NOSEPIECE . . . . . . . . . . . . . . . . . . . . . . . . . 12-13

REQUIRED DAILY PREPARATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13-14

USING THE AIR NAILER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-15

CHANGING DIRECTION OF EXHAUST AIR . . . . . . . . . . . . . . . . . . . 15

CLEARING JAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-16

MANDATORY MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-18

PARTS DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-23

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

1 YEAR LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-26

1 2

Page 3

IMPORTANT INFORMATION ABOUT THIS MANUAL

Improper maintenance and operation are responsible for the majority of accidents involving brad nailers. The largest portion of these could be prevented by recognizing the basic safety rules and precautions. Most accidents can be avoided if the operator recognizes a potentially hazardous situation before it happens and by observing appropriate safety rules and procedures as outlined in this manual.

Basic safety precautions are outlined in the

SSAAFFEETTYY

portion of this manual and

throughout text in this manual where a potential hazard might occur. Hazards that

MMUUSSTT

be avoided to prevent serious injury follow headers marked

DDAANNGGEERR oorr WWAARRNNIINNGG

. These same precautions are placed as labels on the tool

itself.

NNEEVVEERR

use this nailer for applications that are

NNOOTT

specified in this manual.

SAFETY WARNINGS AND PRECAUTIONS

DDoo nnoott ooppeerraattee bbrraadd nnaaiilleerr aannyywwhheerree ffaasstteenneerr mmaayy ccoonnttaacctt hhiiddddeenn eelleeccttrriiccaall wwiirriinngg..

Contact with a “live” wire will make all metal parts of the brad nailer “live.” This can result in severe electrical shock, severe burns or death to the operator. Contact a qualified electrical contractor to ensure a safe working environment exists.

BBee aawwaarree ooff cco

onndduuiittss oorr ggaass ppiippeess..

Striking a gas pipe could result in an explo-

sion causing serious injuries or even death to the operator or bystanders.

BBee aawwaarree ooff wwhhaatt iiss bbeehhiinndd tthhee wwoorrkk ppiieeccee..

A fastener could travel through the work piece and out the other side, striking a bystander resulting in serious injury or even death.

DDoo nnoott ooppeerraattee tthhee bbrraadd nnaaiilleerr iinn tthhee pprreesseennccee ooff ffllaammmmaabbllee lliiqquuiiddss,, ssuucchh aass ggaassoolliinnee,, tthhiinnnneerr,, ppaaiinntt,, oorr aaddhheessiivveess,, ggaasseess oorr dduusstt..

Sparks created by the tool can cause flammable materials to ignite or explode. Failure to comply with this warning could result in serious injury or even death to the operator.

KKeeeepp bbyyssttaannddeerrss,, cchhiillddrreenn aanndd vviissiittoorrss aawwaayy ffrroomm aarreeaa wwhheerree bbrraadd nnaaiilleerr iiss bbeeiinngg uusseedd..

Distractions can result in severe injury or even death to anyone

who inadvertently gets in the way of nailing operations.

DDoo nnoott u

ussee ooxxyyggeenn,, ccoommbbuussttiibbllee oorr bboottttlleedd ggaasseess ((ssuucchh aass ccaarrbboonn

ddiiooxxiiddee oorr nniittrrooggeenn)) aass aa ppoowweerr ssoouurrccee ffoorr t

thhee bbrraadd nnaaiilleerr..

Use

only compressed air from a source as outlined in this manual. The tool will explode resulting in severe injury or even death to the operator and bystanders.

CCAAUUTTIIOONN

used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result in property damage.

NNOOTTEE

provides additional information that is useful for proper use and maintenance of this tool. If a NOTE is indicated make sure it is fully understood.

In addition to

SSAAFFEETTYY AALLEERRTTSS

listed above, there could also be numerous symbols alerting the operator that specific safety equipment is required to safely operate this tool. Learn these

SSAAFFEETTYY SSYYMMBBOOLLSS

as well as the

SSAAFFEETTYY AALLEERRTTSS

to prevent

injury to the operator and to bystanders.

RREEAADD OOPPEERRAATTIINNGG IINNSSTTRRUUCCTTIIOONNSS::

Read and understand tool labels, safety warnings and precautions in this manual before operating the tool. Failure to follow WARNINGS could result in serious injury or even death to the operator or bystanders.

WWEEAARR AAPPPPRROOVVEEDD EEYYEE PPR

ROOTTEECCTTIIOONN::

Safety glasses must conform to the requirements of American National Standards Institute (ANSI) Z87.1 and provide protection against flying particles from both front and side.

WWEEAARR HHEEAARRIINNGG PPRROOTTEECCTTOORRSS::

Hearing protectors should be worn to

protect the ears from loud exhaust noise produced by the air tools.

UUSSEE OONNLLYY CCLLEEAANN,, DDRRYY CCOOMMPPRREESSSSEEDD AAIIRR::

Never use oxygen, combustible gases and any other bottled gas to operate air tools. Using these other sources can cause the air tool to explode.

NNEEVVEERR PPOOIINNTT TTHHEE BBRRAADD NNA

AIILLEERR AATT YYOOUURRSSEELLFF OORR OOTTHHEERRSS::

Fasteners are under extreme pressure and can cause severe injury or even death if misused.

DDOO NNOOTT EEXXCCEEEEDD 112200 ppssii ((88..4433 kkgg//ccmm

GG))..

Using excessive pressure from the power source can cause the brad nailer to explode resulting in severe injury or even death to the operator or bystanders.

Page 4

AAllwwaayyss uussee hheeaarriinngg pprrootteeccttiioonn ttoo pprrootteecctt yyoouurr eeaarrss aaggaaiinnsstt hheeaarriinngg lloossss dduuee ttoo eexxhhaauusstt nnooiissee.. AAllwwaayys

s wweeaarr pprrooppeerr ssaaffee--

ttyy ggllaasssseess ttoo pprreevveenntt iinnjjuurriieess ttoo tthhee eeyyeess ffrroomm ffrraaggmmeennttss ooff

tthhee wwoorrkk ppiieeccee,, ddeeffe

eccttiivvee nnaaiillss oorr ootthheerr ddeebbrriiss ccaauusseedd bbyy uussiinngg tthhee bbrraadd nnaaiill--

eerr..

All safety glasses must have side shields and should conform to the requirements of the American National Standards Institute (ANSI) z87.1. Failure to comply with this warning could lead to serious or permanent damage to the ears as well as serious damage or permanent blindness in the eyes.

NNeevveerr ccaarrrryy tthhee bbrraadd nnaaiilleerr bbyy tthhee

aaiirr hhoossee..

A sudden disconnection of the air hose could cause the brad nailer to remain charged and an accidental firing could occur. Failure to comply with this warning could lead to serious injury to the operator or bystanders.

AAllwwaayyss ddiissccoonnnneecctt tthhee ppoowweerr ssoouurrccee aanndd eennssuurree tthhee ttooooll iiss nnoott cchhaarrggeedd bbeeffoorree llooaaddiinngg ffaas

stteenneerrss..

Failure to comply with this warning could cause severe injury or death to the operator, bystanders and severe damage to the brad nailer.

NNeevveerr uussee aa nnoonn--rreelliieevviinngg aaiirr ccoouupplleerr wwiitthh tthhee bbrraadd nnaaiilleerr..

Always use couplers that release any built-up charge in the brad nailer’s firing mechanism. A non-relieving air coupler can allow the brad nailer to discharge a fastener while the tool is disconnected from the power source. Failure to comply with this warning can result in serious or permanent injury or even death to the operator or to bystanders.

DDoo nnoott ddrriivvee nnaaiillss oonn ttoopp oof

f ootthheerr nnaaiillss..

Do not operate the brad nailer at too steep of an angle. Nails can ricochet. Failure to comply with this warning can result in serious injury or even death to the operator or bystanders.

DDoo nnoott mmooddiiffyy tthhee bbrraadd nnaaiilleerr iinn aannyy wwaayy..

Unauthorized alterations can jeopardize safety in the tool’s operation. Failure to follow this precaution can result in serious injury or even death to the operator or bystanders.

OOnn rrooooffttooppss aanndd ootthheerr hhiigghh llooccaattiioonnss,, aal

lwwaayyss mmoovvee ffoorrwwaarrdd aass yyoouu uussee tthhee

bbrraadd nnaaiilleerr..

You can easily loose your footing if moving backwards. When nailing against a perpendicular surface, nail from the top down. This causes less fatigue and reduces the chances of accidents.

EEnnssuurree tthhee wwoorrkk aarreeaa iiss ssuuffffiicciieennttllyy iilllluummiinnaatteedd ttoo

ooppeerraattee ppoowweerr ttoooollss..

The

work area should be clear and free of litter.

DDoo nnoott ccoonnnneecctt bbrraadd nnaaiilleerr ttoo aann aaiirr ssoouurrccee ccaappaabbllee ooff ggeenneerraattiinngg mmoorree tthhaann 220000 ppssii ((1144..0066 kkgg//ccmm

GG))..

Over-pressurizing the brad nailer will result in bursting, abnormal operation or breakage of the tool. Use only clean, dry, regulated compressed air at levels speci-

fied on the tool. Failure to comply can cause severe injury or death to the operator or bystanders.

DDoo nnoott aatttteemmpptt ttoo ffaasstteenn tthhee ttrriiggggeerr iinn tthhee ““OONN”” ppoossiittiioonn..

This could lead to an accidental discharge of the brad nailer. Do not operate the brad nailer if any portion of the tool’s operating controls are inoperable, disconnected, altered in any way or not in proper working order. Failure to comply with this warning could result in serious injury or even death to the operator or other bystanders.

AAllll aaiirr ccoommpprreessssoorrss mmuusstt ccoommppllyy w

wiitthh tthhee rreeqquuiirreemmeennttss ooff AANNSSII

bb1199..33..

Pressure regulators must be used to limit air pressure where

air supply pressure exceeds the tool’s rated operating pressure.

DDoo nnoott ccaarrrryy tthhee bbrraadd nnaaiilleerr wwiitthh aa ffiinnggeerr oonn tthhee ttrriiggggeerr..

This could lead to an accidental discharge of the brad nailer. Do not press the trigger of the brad nailer unless it is pressed firmly against the work piece. Do not point the brad nailer at yourself or in the direction of another person. Failure to comply with this warning could result in serious injury or even death to the operator or other bystanders.

oo nnoott ttaammppeerr wwiitthh tthhee wwoorrkk ppiieeccee ccoonnttaacctt..

The work piece contact prevents accidental discharge of the brad nailer and should never be removed or compromised in any way. Failure to comply with this warning could result in serious injury or even death to the operator or other bystanders.

AAllwwaayyss ddiissccoonnnneecctt aaiirr hhoossee aanndd rreemmoovvee aannyy rreemmaaiinniinngg nnaaiills

s::

1. When brad nailer is left unattended.

2. Before performing any maintenance or repair on the brad nailer.

3. Before attempting to clear a jam in the brad nailer.

4. Before moving the brad nailer to a new location.

AAllwwaayyss cchheecckk tthhee oovveerraallll ccoonnddiittiioonn ooff tthhee bbrraadd nnaaiilleerr bbeeffoorree uussiinngg.. CChheecckk ffoorr aanndd ttiigghhtteenn aannyy llo

ooossee ssccrreewwss..

Ensure all safety systems are in working condition before using the brad nailer. The brad nailer must not operate if only the trigger is pulled or if only the work piece contact is pressed against the work piece. The brad nailer must only be used if both the trigger and work piece contact work at the same time.

Page 5

COMPONENT INSTALLATION

NNeevveerr uussee aa nnoonn--rreelliieevviinngg aaiirr ccoouupplleerr wwiitthh tthhee bbrraadd nnaaiill--

eerr..

When selecting an air compressor, it must comply with the requirements of the American National Safety Institute - ANSI B19.3.

Choose an air compressor that can supply more than the required air pressure to ensure optimum efficiency. Always use clean, dry compressed air with a maximum pressure of 200 psi. Use a pressure regulator and set the pressure between 70 – 120 psi. (5.0 – 8.5 kg/cm

G). Before each use, check the pressure regulator to

ensure it is functioning within the proper pressure range.

UUssiinngg aann aaiirr pprreessssuurree ooff mmoorree tthhaann 112200 ppssii ccaann

ccaauussee tthhee bbrraadd nnaaiilleerr ttoo mmaallffuunnccttiioonn oorr ppoossssiibbllyy eex

xppllooddee ccaauussiinngg

sseevveerree iinnjjuurryy oorr pprrooppeerrttyy ddaammaaggee..

SSEELLEECCTTIINNGG AA PPRROOPPEERR AAIIRR HHOOSSEE

Use an air hose with the largest diameter and shortest length possible to ensure continuous, efficient nailing operations. Using an air pressure of 70 psi (5.0 kg/cm

G), an air hose with an inside diameter of 1/4" (6.5 mm) or greater and a hose length of less than 6.6 ft (20 m), it is recommended that a 0.5 second interval be allowed between each nailing. Air supply hoses shall have a minimum working pressure of 150 psi (10.7 kg/cm

G) or 150% of the maximum pressure produced by the

compressor or whichever is higher.

LLooww aaiirr oouuttppuutt bbyy tthhee ccoommpprreessssoorr oorr aa lloonnggeerr hhoossee wwiitthh

aa ssmmaalllleerr iinnssiiddee ddiiaammeetteerr iinn rreellaattiioonn ttoo tth

hee nnaaiilliinngg ffrreeqquueennccyy mmaayy ddeeccrreeaassee

tthhee ddrriivviinngg ccaappaabbiilliittyy ooff tthhee aaiirr nnaaiilleerr..

SSEELLEECCTTIINNGG AA QQUUIICCKK DDIISSCCOONNN

NEECCTT

1. Remove the plastic protective plug

from the tool’s air inlet.

2. Insert a 1/4" NPT male quick

disconnect into the air inlet. Install the female portion to the air hose.

TThhoorroouugghhllyy cclleeaann aanndd mmaaiinnttaaiinn tthhee bbrraadd nnaaiilleerr aafftteerr eevveerryy uussee..

Lubricate moving parts to prevent rust and minimize friction-related wear. Wipe down the entire tool and remove all dust from the moving parts. Properly store the brad nailer in a suitable case to keep it ready for the next job.

AAllll mmaaiinntteennaannccee aanndd rreeppaaiirrss sshhoouulld

d bbee ppeerrffoorrmmeedd bbyy aann aauutthhoorriizzeedd rreeppaaiirr

ffaacciilliittyy..

Call 1-888-278-8092 to obtain a list of repair facilities in your area or

to make arrangements to return the tool for service.

FUNCTIONAL DESCRIPTION

CCOONNTTRROOLLSS AANNDD CCOOMMPPOONNEENNTTSS::

1. Exhaust Cover

2. Trigger

3. Jam Clearing Door

4. No-mar Nosepiece

5. Empty Magazine Indicator

6. Nail Depth Adjuster

7. Hanging Hook

8. Air Inlet

9. Nail Magazine Lever

10. Nail Magazine Cover

11. Work Piece Contact

12. Trigger Actuation Mode Selector

AACCCCEESSSSOORRIIEESS::

13. Lubricant

14. Safety Glasses

15. Hex Wrenches (2)

16. F32 - Brad Strips

Page 6

OOPPEERRAATTIIOONN IINN SSIINNGGLLEE SSEEQQUUEENNTTIIAALL AACCTTUUAATTIIOONN MMOODDEE

To select the Single Sequential Actuation Mode (see Figure 1):

1. Press and hold the red Actuation Selector embedded in the trigger.

2. Rotate Actuation Selector down to the Single Sequential Actuation (T).

3. Release Actuation Selector, ensuring locking tab is fully seated in the slot.

EEnnssuurree sseelleeccttoorr hhaass lloocckkeedd iinnttoo ppoossiittiioonn.. EEnnssu

urree

aaccttuuaattiioonn pprroocceessss iiss ffuullllyy uunnddeerrssttoooodd bbeeffoorree aatttteemmppttiinngg ttoo uussee bbrraadd nnaaiilleerr..

TTOO UUSSEE TTHHEE BBRRAADD NNAAIIL

LEERR IINN SSIINNGGLLEE SSEEQQUUEENNTTIIAALL

AACCTTUUAATTIIOONN MMOODDEE::

1. Firmly grip brad nailer handle.

2. Position brad nailer work piece contact on work piece surface.

3. Push brad nailer against work piece compressing work piece contact.

4. Pull trigger on brad nailer to drive nail. The brad nailer will recoil away from the work piece as nail is driven.

5. Remove finger from trigger and lift brad nailer away from surface of work piece.

OOPPEERRAATTIIOONN IINN CCOONNTTAACCTT AACCTTUUAATTIIOONN MMOODDEE

WWhheenn uussiinngg ccoon

nttaacctt aaccttuuaattiioonn mmooddee,, bbee ccaarreeffuull ooff uunniinn--

tteennttiioonnaall ddoouubbllee ffiirreess rreessuullttiinngg ffrroomm ttooooll rreeccooiill.. UUnnwwaanntteed

d ffaasstteenneerrss mmaayy bbee

ddrriivveenn iiff tthhee wwoorrkk ppiieeccee ccoonnttaacctt iiss aalllloowweedd ttoo aacccciiddeennttaallllyy rree--ccoonnttaacctt tthhee wwoorrkk ppi

ieeccee..

9 10

To improve the connection between the quick disconnect and air nailer, and to help prevent oxidation, apply PTFE tape or joint compound to the connector threads before insertion.

3. Snap the air hose onto the quick disconnect on the air nailer. Check for air leaks.

LLUUBBRRIICCAATTIIOONN

To ensure maximum performance, it is recommended to install an air set (oiler, regulator, and air filter) as close as possible to the air nailer. Adjust the oiler so that approximately one drop of oil will be released for every 50 nails.

If an air set is not used or is unavailable, oil the tool using pneumatic tool oil by placing 2 or 3 drops into the air inlet. This should be done before and after use. For proper lubrication, the tool must be fired several times after the oil is introduced to the filter.

OPERATING THE BRAD NAILER

AAllwwaayyss uussee hheeaarriinngg pprrootteeccttiioonn ttoo pprrootteecctt yyoouurr eeaarrss aaggaaiinnsstt hheeaarriinngg lloossss dduuee ttoo eexxhhaauusstt nnooiissee.. AAllwwaayys

s wweeaarr pprrooppeerr ssaaffee--

ttyy ggllaasssseess ttoo pprreevveenntt iinnjjuurriieess ttoo tthhee eeyyeess ffrroomm ffrraaggmmeennttss ooff

tthhee wwoorrkk ppiieeccee,, ddeeffe

eccttiivvee nnaaiillss oorr ootthheerr ddeebbrriiss ccaauusseedd bbyy uussiinngg tthhee bbrraadd nnaaiill--

eerr..

AAllwwaayyss ddiissccoonnnneecctt tthhee aaiirr hhoossee bbeeffo

orree mmaakkiinngg aaddjjuussttmmeennttss oorr cchheecckkiinngg tthhee

ffuunnccttiioonnaalliittyy ooff tthhee aaiirr nnaaiilleerr..

SELECT TRIGGER ACTUATION MODE

The brad nailer is equipped with a selectable trigger. This allows the selection of

SSiinnggllee SSeeqquueennttiiaall AAccttuuaattiioonn MMooddee

CCoonnttaacctt AAccttuuaattiioonn MMooddee

Figure 1

Page 7

To select Contact Sequential Actuation Mode (see Figure 2):

1. Press and hold Actuation Selector embedded in the trigger.

2. Rotate Actuation Selector up to the Contact Sequential Actuation (TTT).

3. Release Actuation Selector, ensuring locking tab is fully seated in the slot.

EEnnssuurree sseelleeccttoorr hhaass lloocckkeedd iinnttoo ppoossiittiioonn.. EEnnssuurree

aaccttuuaattiioonn pprroocceessss iiss ffuullllyy uunnddeerrssttoooodd bbeeffoorree aatttteemmppttiinngg ttoo uussee bbrraadd nnaaiilleerr..

TTOO UUSSEE TTHHEE BBRRAADD NNAAIILLEERR IINN CCOONNTTAACCTT AACCTTUUAATTIIOONN MMOODDEE::

1. Firmly grip brad nailer handle.

2. Pull and hold the brad nailer trigger.

3. Push brad nailer against work piece compressing work piece contact.

4. The brad nailer will drive nail upon contact. The brad nailer will recoil away from the work piece as nail is driven.

ADJUSTING DEPTH OF NAILING

BBee aawwaarree ooff mmaatteerriiaall tthhiicckknneessss wwhheenn uussiinngg nnaaiilleerr.. AA pprroo--

ttrruuddiinngg nnaaiill mmaayy ccaauussee iinnjjuurryy..

Adjust the depth of nailing by turning the adjustment knob (Figure 3, Item 1) to the left (A) for the deepest setting and to the right (B) for the shallowest setting. To increase the depth of the nails, when the adjustment knob is already set to its highest setting, increase the air pressure. To decrease the depth of nails when the adjustment knob is already set to its lowest setting, decrease the air pressure. Should nails be driven too deep even when the adjustment knob is set at its lowest setting, decrease the air pressure. In general, the brad nailer will have a longer service life when the adjustment knob is set at a lower setting causing less wear and tear on the driving mechanism.

AAllwwaayyss ddiissccoonnnneecctt tthhee bbrraadd nnaaiilleerr bbeeffoorree mmaakkiinngg aannyy

aaddjjuussttmmeennttss ttoo tthhee nnaaiill ddeepptthh kknnoobb..

USING THE HOOK

AAllwwaayyss ddiissccoonnnneecctt tthhee aaiirr hhoossee bbeeffoorree hhaannggiinngg tthhee bbrraadd nnaaiilleerr wwiitthh tthhee hhooookk.. NNEEVVEERR hhooookk tthhee bbrraadd nnaaiilleerr iinn aa hhiigghh llooccaattiioonn oorr oonn aann uunnssttaabbllee ppllaattffoorrmm..

LOADING NAILS INTO THE AIR NAILER

AAllwwaayyss ddiissccoonnnneecctt tthhee aaiirr hhoossee ffrroomm tthhee nnaaiilleerr bbeeffoorree aaddddiinngg oorr rreemmoovviinngg nnaaiillss ttoo tthhee bbrraadd nnaaiilleerr..

NEEVVEERR uussee ddeeffoorrmmeedd nnaaiillss oorr nnaaiill ssttrriipp.. FFaaiilluurree ttoo oobbsseerrvvee tthhiiss pprreeccaauuttiioonn

ccaann rreessuulltt iinn ppoooorr nnaaiill ffe

eeeddiinngg aanndd//oorr jjaammss iinn tthhee ffeeeeddiinngg mmeecchhaanniissmm..

To load nails in brad nailer, depress magazine lever and pull magazine cover to back of magazine. (Figure 4). Insert nails and slide magazine cover over nails until it locks into place.

USING THE NO-MAR NOSEPIECE

AAllwwaayyss ddiissccoonnnneecctt tthhee aaiirr hhoossee bbeeffoorree aattttaacchhiinngg tthhee

nnoo--mmaarr nnoosseeppiieeccee..

Figure 3

Figure 2

Figure 4

Page 8

6. Select Single Sequential Actuation Operation. Check for leaks. Without pulling the trigger, press the work piece contact against the work piece. The tool MUST NOT operate. Holding the tool away from the work piece, pull trigger and hold for 5 seconds. The tool MUST NOT operate. Repeat steps several times. Without pulling trigger, press nailer against work piece and pull trigger. The tool MUST operate. Release trigger. Driver MUST move up.

7. Select Contact Actuation Operation. Holding nailer away from work piece, pull trigger. The tool MUST NOT operate. While still pulling trigger, press the nailer against work piece. The tool MUST operate.

8. If Steps 1 through 7 function properly, prepare the tool for use. Select operation mode and load fasteners.

9. Set the required depth of drive.

10.Repeat these steps daily. Test again if the nailer is dropped, jammed, etc.

USING THE AIR NAILER

To drive a nail, place the work piece contact of the brad nailer against the work piece and pull the trigger. See Figure 6.

To avoid any unexpected nailings, perform the operation as follows:

1. Avoid placing the work piece contact against the work piece with excessive force.

2. Pull the trigger fully and hold it in the fired position for 1 to 2 seconds before releasing the trigger. This will give the brad nailer time to completely expend the previous nail and build enough pressure for the next nail.

DDOO NNOOTT hhoolldd tthhee ttrriiggggeerr iinn aa hhaallff--ppuulllleedd ppoossiittiioonn..

This could cause an unexpected nailing to occur if the work piece contact is permitted to re-contact the work piece. Failure to comply could result in damage to work piece.

In order to prevent the surface of the work piece from being scratched or damaged, use the no-mar nosepiece. Install no-mar nosepiece by pressing it into place on the nose frame. See Figure 5.

Store the no-mar nosepiece in place when not being used.

NNeevveerr uussee aa nnoonn--rreelliieevviinngg aaiirr ccoouupplleerr wwiitthh tthhee bbrraadd nnaaiill--

eerr.. AAllwwaayyss uussee ccoouupplleerrss tthhaatt rreelleeaassee a

annyy bbuuiilltt--uupp cchhaarrggee iinn tthhee bbrraadd nnaaiilleerr’’ss

ffiirriinngg mmeecchhaanniissmm.. AA nnoonn--rreelliieevviinngg aaiirr ccoouupplleerr ccaann aallllooww tthhee

bbrraadd nnaaiilleerr ttoo

ddiisscchhaarrggee aa ffaasstteenneerr wwhhiillee tthhee ttooooll iiss ddiissccoonnnneecctteedd ffrroomm tthhee ppoowweerr ssoouurrccee.. FFaaiilluurree tto

o ccoommppllyy wwiitthh tthhiiss wwaarrnniinngg ccaann rreessuulltt iinn sseerriioouuss oorr ppeerrmmaanneenntt iinnjjuurryy

oorr eevveenn ddeeaatthh ttoo tthhee ooppeerraattoorr oor

r ttoo bbyyssttaannddeerrss..

When the air hose is disconnected, the pressure reservoir in the brad nailer will discharge removing any built up air inside the tool.

REQUIRED DAILY PREPARATION

The following steps should be performed on a daily basis to ensure the brad nailer is operating correctly:

1. Disconnect air supply from nailer and remove fastener strip.

2. Check all screws, nuts and pins and ensure all are tight.

3. Press the pusher release button and slide back the pusher assembly (Overriding the reload indicator). Press the work piece contact against a work piece ensuring smooth movement.

4. With work piece contact against the work piece, pull trigger. The trigger must operate smoothly.

5. Connect air supply and set regulator for 70 psi. DO NOT load a fastener strip.

Figure 6

Figure 5

Page 9

OOVVEERRAALLLL MMAAIINNTTEENNAANNCCEE OOFF AAIIRR NNAAIILLEERR

AAllwwaayyss ddiissccoonnnneecctt tthhee aaiirr hhoossee ffrroomm aaiirr nnaaiilleerr bbeeffoorree

aatttteemmppttiinngg a

annyy ttyyppee ooff mmaaiinntteennaannccee oorr vviissuuaall iinnssppeeccttiioonn ooff ttooooll..

Always visually inspect air nailer before every use. Check on the overall condition and for any loose screws. Tighten any screws that have come loose. See Figure 9.

Visually inspect the work piece contact and trigger to ensure there is free movement. See Figure 10.

When the tool is not going to be used for an extended period, wipe off all dust and debris that have collected on it. Tighten all loose screws. Lubricate the firing mechanism with pneumatic tool oil. See page 9 for Lubrication.

Store the brad nailer in a safe location or in suitable carrying case. It is recommended that the brad nailer be secured in a locked location to prevent unauthorized usage.

Avoid exposure to direct sunlight and/or locations with high humidity and heat.

RReemmoovvee tthhee bbrraadd nnaaiilleerr ffrroomm uussee aanndd s

scchheedduullee ttoo hhaavvee

iitt rreeppaaiirreedd aatt aann aauutthhoorriizzeedd rreeppaaiirr ffaacciilliittyy iiff tthhee wwoorrkk ppiieeccee ccoonnttaacctt iiss bbiinndd-- iinngg

oorr nnoott mmoovviinngg ffrreeeellyy.. DDoo nnoott aatttteemmpptt ttoo rreeppaaiirr tthhee bbrraadd nnaaiilleerr.. FFaaiilluurree ttoo

ccoommppllyy ccaann rreessuulltt iinn mmaallf

fuunnccttiioonn ooff tthhee ttooooll aanndd sseevveerree iinnjjuurryy ttoo tthhee ooppeerraa--

ttoorr oorr aannyy bbyyssttaannddeerrss..

CHANGING DIRECTION OF EXHAUST AIR

The direction of exhaust air on the air nailer can be directed 360˚ degrees by placing hand on exhaust cover and turning. See Figure 7.

CLEARING JAMS

Typically, jams are caused when a fastener or a fastener fragment becomes wedged between the driver blade and nail guide. Using the wrong fastener can also cause jams.

TTOO CCLLEEAARR AA JJAAMM::

1.Disconnect the air supply and remove the fastener strip. Leave the pusher assembly open.

2.Pull out the latch tab and open the jam-clearing door.

3.Remove all debris that has built up during operation.

4.Remove jammed fastener. If fastener is difficult to grasp, use needle nose pliers instead of fingers.

5.If necessary, insert a flat-blade screwdriver so that it touches the tip of the driver blade. See Figure 8. Tap the screwdriver with a hammer. The screwdriver will push the driver blade back, freeing the jam.

6.Close the jam-clearing door securely.

MAINTENANCE

SSTTOORRAAGGEE OOFF NNAAIILLSS

Always handle nail strips and their box very carefully. If the nail strips have been mishandled, they may be out of shape or have breaks in the connecting strips. This will cause the nails to feed poorly and possibly result in misfiring or jams in the air nailer.

Avoid storing nails in a very humid or hot environment or place in direct sunlight.

15 16

Figure 8

Figure 9

Figure 10

Figure 7

Page 10

PPRROOBBLLEEMM PPOOSSSSIIBBLLEE CCAAUUSSEE SSOOLLUUTTIIOONN

MANDATORY MAINTENANCE

AAllll mmaaiinntteennaannccee aanndd rreeppaaiirrss sshhoouulldd bbee ppeerrffoorrmmeedd bbyy aann

aauutthhoorriizzeedd rreeppaaiirr ffaacciilliittyy.. CCaallll 11--888888--227788--88009

922 ttoo oobbttaaiinn aa lliisstt ooff rreeppaaiirr ffaacciill--

iittiieess iinn yyoouurr aarreeaa oorr ttoo mmaakkee aarrrraannggeemmeennttss ttoo rreettuurrnn tthhee ttooooll ffo

orr sseerrvviiccee..

AACCTTIIOONN RREEAASSOONN OOPPEERRAATTIIOONN

TROUBLESHOOTING

Most minor problems can be resolved quickly and easily using the troubleshooting table below. For problems that cannot be solved, contact Alltrade Customer Service (toll free) at 1-888-278-8092.

PPRROOBBLLEEMM PPOOSSSSIIBBLLEE CCAAUUSSEE SSOOLLUUTTIIOONN

Clean magazine and feeder mechanism.

Prevents brad nailer from jamming.

Use compressed air and clean daily.

Inspect and ensure work piece contact operates properly.

Ensures operator safety and keeps brad nailer working efficiently.

Use compressed air and clean daily.

Lubricate brad nailer after every use using pneumatic tool oil.

Extends life of brad nailer.

Apply 2 – 3 drops of pneumatic tool oil to brad nailer air inlet after every use.

Weak drive. Slow to cycle between nailings.

Ensure proper air pressure is being used.

Inspect for worn driver blade.

Inspect piston O-ring for wear or damage.

Increase air pressure, Do not exceed 120 psig

(8.3 bars, 8.5 kg/cm

)

Contact Customer Service.

Nails driven too deep. Check air pressure. Reduce air pressure.

Brad nailer feeds intermittently or skips nails.

Ensure correct nails are being used.

Inspect nail feeder mechanism.

Piston O-ring damaged or worn

Nail feeder worn or damaged.

Use ONLY recommended nails.

Clean and lubricate nail feeder.

Use recommended pneumatic tool oil.

Contact Customer Service.

Replace nail feeder.

Nails jam or driven nail is bent.

Ensure correct nails are being used.

Inspect for worn driver blade.

Nail feeder worn or damaged.

Use ONLY recommended nails.

Contact Customer Service.

Replace nail feeder.

Drives nails properly during normal nailing operations, but fails to drive nails fully at faster operating speeds.

Check inside diameter of air hose.

Switch to air hose with larger inside diameter.

Nailer operates, but no nail is driven.

Check for jammed nail. Inspect nail feeder

mechanism. Ensure correct nails are

being used.

Clear jammed nail. Clean and lubricate nail

feeder. Use ONLY recommend-

ed nails.

17 18

Page 11

PARTS LIST

IITTEEMM NNOO.. PPAARRTT NNOO.. DDEESSCCRRIIPPTTIIOONN

PARTS DIAGRAM

19 20

1 A0000-1211 Nylon Screw M4*8 2 A0005-0691 Washer 12*1 3 A0304-0651 Exhaust Cover 4 A0200-1471 O-Ring 7.59*2.62 5 B0000-0051 Screw Set M5*20 6 A0000-0091 Screw M5*20 7 A0005-0031 Washer #5*1.21 8 A0301-1551 Cap, Top

9 A0311-0451 Seal, Air 10 A0200-0221 O-Ring 15*2.5 11 A0205-0651 Gasket 12 A0100-0631 Spring 13 K0300-2221 Firing Valve Piston Set 14 A0200-0711 O-Ring 33.5*2.5 15 A0308-0341 Firing Valve Piston 16 A0200-0601 O-Ring 26.59*2.95 17 A0313-0041 Piston Stopper 18 K0600-4291 Piston Unit 19 A0200-1281 O-Ring 22.4*3.3 20 B0600-4271 Piston Set 21 A0305-0081 Sleeve Retainer 22 A0200-0271 O-Ring 44.8*2.6 23 A0800-0391 Spacer 24 A0200-0071 O-Ring 31*2.5

Page 12

IITTEEMM NNOO.. PPAARRTT NNOO.. DDEESSCCRRIIPPTTIIOONN

25 A0303-0941 Sleeve, Cylinder 26 A0309-0741 Bumper 27 K0400-0601 Body and Handle Grip 28 A0204-1661 Grip 29 A0401-1951 Body 30 A0310-0751 Nozzle 31 A0006-0821 Trigger Pin 32 A0005-0311 Pin Retainer 5.5*2 33 A0011-0161 Spring Pin 3*24 34 A0313-0631 Main Body Bumper L(Snap-on) 35 A0313-0641 Main Body Bumper R(Snap-on) 36 A0006-0411 Pin 37 A0005-0291 Pin Retainer 6*2.9 38 A0316-0331 Belt Hook 39 A0200-2851 O-Ring 38*3.5W 40 A0203-0191 Filter 41 A0306-1181 Tail Cover 42 A0101-0191 Spring 43 A0709-0301 Click Lever 44 A0712-0341 Safety Guide Plate 45 A0100-0811 Spring 46 A0200-1091 O-Ring 11*1.05 47 K0500-1381 Trigger Valve Set 48 K0500-1491 Trigger Set 49 K0800-0111 Driver Guide Cover Set

50 K0700-2531 Release Catch Assembly 51 A0005-0041 E-Ring2.5 52 A0711-0841 Release Catch (C) 53 A0011-0181 Spring Pin 3*8 54 A0200-4301 O-Ring 4.4*1.8 55 A0004-0181 Safety Adjustment Wheel 56 A0711-0831 Release Catch (B) 57 A0006-0491 Step Pin 58 A0000-0071 Screw M5*16 59 A0800-0211 Spacer 60 A0011-0011 Spring Pin 2*10 61 A0001-0001 Screw M4*18 62 A0801-0771 Driver Guide 63 A0000-0851 Screw M4*10 64 A0710-0272 Spacer 65 A0701-2561 Lower Magazine 66 A0708-0321 Steel Bar 67 A0706-0561 Support 68 A0715-0161 Magazine Stop 69 A0000-0241 Screw M5*14 70 A0000-0521 Nylon Screw M4*12 71 A0707-1391 Pusher 72 A0700-1781 Upper Magazine 73 A0011-0131 Spring Pin 3*10 74 A0718-0141 Tail Cover

Page 13

WWAARRRRAANNTTYY PPEERRFFOORRMMAANNCCEE

By purchasing this product, purchaser expressly acknowledges and agrees that their sole and exclusive remedy under this warranty shall be strictly limited to the repair or replacement of any covered nonconforming items or parts thereof provided that any such nonconforming item and/or part is promptly returned to an authorized Service Center within the applicable warranty period, with a written request by purchaser that Alltrade repair and/or replace the nonconforming item and/or part. We recommend that you keep the original product packaging in the event you need to ship the unit. We suggest the package be insured against loss or in transit damage. When sending your product, include your name, address, phone number, email address, dated proof of purchase (or copy) and a statement about the nature of the problem. Warranty coverage is conditioned upon purchaser furnishing Alltrade with adequate written proof that they are the original purchaser and of the original purchase date. Parts returned, freight prepaid and insured, will be inspected and, at Alltrade's option, repaired and/or replaced free of charge if it is found to be defective and subject to warranty. Alltrade retains the sole discretion to determine whether any item or part is nonconforming and, if so, whether the item and/or part will be repaired and/or replaced. If the unit is repaired, new or reconditioned replacement parts may be used. If Alltrade chooses to replace the product, it may replace it with a new or reconditioned of the same or comparable design. The repaired or replaced unit will be warranted under the terms of the remainder of the one year warranty period; covered defective parts not subject to normal wear and tear or other exclusions will be repaired or replaced, at Alltrade's option. During the warranty period, Alltrade will be responsible for the return shipping charges. Alltrade's repair and/or replacement of any nonconforming item and/or part thereof shall constitute fulfillment of all obligations to the purchaser. Alltrade shall not be responsible or liable for any expense, including freight charges, or repairs made outside Alltrade's facility or an Alltrade designated service, unless expressly agreed to by Alltrade in writing. Under no circumstances shall Alltrade bear any responsibility for loss of the unit, loss of time or rental, inconvenience, commercial loss, or consequential damages.

For the location of an Authorized Service Center nearest you, please call customer service at 1-888-278-8092.

EEXXCCLLUUSSIIOONNSS

Air nailers and staplers need periodic maintenance to remain in proper operating condition. Normal wear parts (o-rings and driver blades) shall be warranted to the original purchaser to be free from defects in materials and workmanship for a period of 90 days from the original date of purchase.

This warranty does not cover parts damaged due to normal wear, abnormal conditions, misapplication, misuse, abuse, accidents, operation, improper storage, or freight damage. Parts damaged or worn by operation in dusty environments are not warranted. Failure to follow recommended operating and maintenance procedures

IITTEEMM NNOO.. PPAARRTT NNOO.. DDEESSCCRRIIPPTTIIOONN

SPECIFICATIONS

1 YEAR LIMITED WARRANTY

EExxpprreessss aanndd EExxcclluussiivvee LLiimmiitteedd WWaarrrraannttyy ttoo OOrriiggiinnaall RReettaaiill BBuuyyeerr

Alltrade Tools LLC (hereinafter "Alltrade") expressly warrants to the original retail purchaser of the accompanying SNAP-ON™ portable air tool and no one else all parts of the product (except those parts referred to below which are specifically excluded from such warranty (see Exclusions) to be free from defects in materials and workmanship for a period of one year from the original date of purchase.

The date of purchase shall be the date of shipment to the original purchaser, or the date the original purchaser took possession, custody, or control of the product, whichever occurred first. This warranty shall be null and void if the product or any component thereof is modified or altered. This warranty does not apply to any other product and/or component thereof manufactured or distributed by Alltrade, and does not apply to products and/or components thereof designed, manufactured and/or assembled by others, for which Alltrade makes no warranties whatsoever.

TTHHEERREE AARREE NNOO WWAARRRRAANNTTIIEESS,, WWHHIICCHH EEX

XTTEENNDD BBEEYYOONNDD TTHHEE DDEESSCCRRIIPPTTIIOONN OONN

TTHHEE FFAACCEE HHEERREEOOFF..

MODEL NUMBER 870015 AIR PRESSURE

70-120 PSIG (5.0- 8.5 kg/cm2G) NAIL LENGTH 5/8" (15 mm) - 2" (50.8 mm) NAIL CAPACITY 110 NAILS MINIMUM HOSE

DIAMETER

1/4" (6.5 mm)

NAIL DIAMETER 18 GAUGE NET WEIGHT 2.6 LBS. (1.17KG)

75 A0706-1741 Spring Holder 76 A0200-0291 O-Ring 4*1.25 (red) 77 A0101-0351 Spring 78 A00204-1571 No-Mar Pad

Page 14

PURCHASER'S SOLE AND EXCLUSIVE REMEDY IS AS STATED ON PRECEDING PAGES.

LLIIMMIITTAATTIIOONNSS OOFF LLIIAABBIILLIITTYY

IN NO EVENT SHALL ALLTRADE AND/OR ITS REPRESENTATIVE(S) BE LIABLE FOR INDIRECT, INCIDENTAL, SPECIAL AND/OR CONSEQUENTIAL DAMAGES OF ANY KIND ARISING OUT OF OR RELATED TO, DIRECTLY OR INDIRECTLY, ANY BREACH OR PROVISION OF ANY AGREEMENT BETWEEN ALLTRADE AND/OR ITS REPRESENTATIVE(S) AND PURCHASER, AND WARRANTY HEREUNDER, AND/OR THE EXISTENCE, DESIGN, MANUFACTURE, PURCHASE, USE AND/OR OPERATION OF ANY ITEM(S) SOLD HEREUNDER EVEN IF ALLTRADE AND/OR ITS REPRESENTATIVE(S) HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH DAMAGES. IN NO EVENT, WHETHER BECAUSE OF A BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE) OR OTHERWISE, SHALL ALLTRADE'S AND/OR ITS REPRESENTATIVE (S) LIABILITY EXCEED THE PRICE OF THE PRODUCT. All LIABILITY CONNECTED WITH THE USE OF THIS PRODUCT SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY PERIODS SPECIFIED ABOVE.

LLIIMMIITTAATTIIOONNSS OONN WWAARRRRAANNTTYY DDIISSCCLLAAIIMMEERRSS

Some states do not allow limitations on how long an implied warranty lasts and some states do not allow the exclusion or limitation of the incidental or consequential damages, so part or all of the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.

If your product is not covered by this warranty, please call our Customer Service Department at 1-888-278-8092 for general repair information, and charges and the location of your nearest authorized service facility.

also voids warranty. DAMAGE TO THE PRODUCT RESULTING FROM TAMPERING, ACCIDENT, ABUSE,

NEGLIGENCE, FAILURE TO FOLLOW INSTRUCTIONS, UNAUTHORIZED REPAIRS OR ALTERATIONS, DAMAGE WHILE IN TRANSIT TO OUR SERVICE FACILITY, USE OF UNAPPROVED OR IMPROPER ATTACHMENTS OR ACCESSORIES, OR OTHER CAUSES UNRELATED TO PROBLEMS WITH MATERIAL OR WORKMANSHIP ARE NOT COVERED BY THIS WARRANTY.

Alltrade will not be liable for the following: labor charges, loss or damage resulting from improper operation, maintenance or repairs made by other persons; pre-delivery services such as assembly, oil and lubricants, and adjustment; maintenance services that are normally required to maintain the product.

The use of other than genuine Snap-On™ Repair Parts will VOID the warranty.

WWAARRRRAANNTTYY DDIISSCCLLAAIIMMEERRSS

EXCLUSION AND DISCLAIMER OF ALL OTHER EXPRESS WARRANTIES, GUARANTIES AND/OR REPRESENTATIONS, EXCEPT FOR THE LIMITED WARRANTY PROVIDED HEREIN, ALL OTHER EXPRESS WARRANTIES, GUARANTIES, AND/OR REPRESENTATIONS BY ALLTRADE AND OR ITS REPRESENTATIVE(S) REGARDING THE DESIGN, MANUFACTURE, PURCHASE, USE AND/OR OPERATION OF THE PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER, REGARDLESS OF WHETHER ANY SUCH WARRANTY, GUARANTY AND/OR REPRESENTATION, WRITTEN OR ORAL, ARISES BY OPERATION OF LA W AND/OR EQUITY AND/OR BY ANY ACT OR OMISSION OF ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE BUYER, ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE AND/OR ITS REPRESENTATIVES. PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS, CLAIMS AND/OR CAUSE OF ACTION ARISING THEREFROM OR BASED THEREON. PURCHASER'S SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE.

EXCLUSION AND DISCLAIMER OF ALL IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. NO WARRANTY, ORAL OR WRITTEN, OTHER THAN THE WARRANTY LISTED HEREIN IS MADE WITH REGARD TO THIS PRODUCT. ALL WARRANTIES AND/OR IMPLIED WARRANTIES, GUARANTIES AND/OR REPRESENTATIONS BY ALLTRADE AND/OR ITS REPRESENTATIVE(S) REGARDING THE DESIGN, MANUFACTURE, PURCHASE, USE AND/OR OPERA TION OF THE PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER, REGARDLESS OF WHETHER ANY SUCH WARRANTY, GUARANTY AND/OR REPRESENTATION, WRITTEN OR ORAL, ARISES BY OPERATION OF LAW AND/OR EQUITY AND/OR BY ANY ACT OR OMISSION OF ALLTRADE AND/OR ITS REPRESENTATIVES. PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS, CLAIMS AND/OR CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON.

Snap-On 870015 Instruction Manual

Specifications and Main Features

Frequently Asked Questions

User Manual