Snap-On 692024 Instruction Manual

COMPONENT 692024

FOR CUSTOMER SERVICE

1-888-278-8092

Printed in China

3021528

Conforms to Std. UL 1776
Certified to CAN/CSA-C22.2
STD No.68-92

THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION,
MAINTENANCE AND STORAGE OF THIS PRODUCT. BEFORE USE, READ CAREFULLY AND
UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND PRODUCT LABELS. FAILURE TO DO SO
COULD RESULT IN SERIOUS PERSONAL INJURY AND/OR PROPERTY DAMAGE.

IF YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A PROBLEM WITH YOUR SNAP-ON
PRODUCT, DO NOT RETURN THIS PRODUCT TO THE STORE. PLEASE CALL OUR CUSTOMER SERVICE
DEPARTMENT AT

11--888888--227788--88009922

. BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION
AVAILABLE: MODEL No., DATE PURCHASED AND STORE LOCATION. AN ALLTRADE
REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE.

SNAP-ON™IS A TRADEMARK LICENSED BY SNAP-ON™CORP.,
U.S.A., WHICH DOES NOT MANUFACTURE OR
DISTRIBUTE THIS PRODUCT. CONSUMER INQUIRES SHOULD BE
DIRECTED TO:

©COPYRIGHT 2010 ALLTRADE TOOLS, LLC.
1431 VIA PLATA
LONG BEACH, CA 90810-1462 USA

870785 – 2000 PSI Electric Pressure Washer_Rev 06/01/11

2000 PSI ELECTRIC
PRESSURE WASHER

INSTRUCTION MANUAL

For consumer questions or comments,
please call 1-888-278-8 092.

Days/Hours of operation:
9am-7pm EST Monday - Friday
10am-6pm EST Saturday - Sunday

English and Spanish Speaking
Customer Service Representatives are
Available.

INTRODUCTION

This instruction manual is intended for your benefit. Please read and follow the safe­ty, installation, maintenance and troubleshooting steps described within to ensure
your safety and satisfaction. The contents of this instruction manual are based upon
the latest product information available at the time of publication. The manufactur­er reserves the right to make product changes at any time without notice.

GENERAL SAFETY

READ AND FOLLOW ALL INSTRUCTIONS.

Failure to follow all instructions in this manual may result in severe
personal injury or death. Keep this manual and refer to it for Safety
Instructions, Operating Procedures, and Warranty.

SAVE THESE INSTRUCTIONS FOR

FUTURE REFERENCE.

RECOGNIZE SAFETY SYMBOLS, WORDS AND LABELS

The safety instructions provided in this manual are not intended to cover all possible
conditions and practices that may occur when operating, maintaining and cleaning
power tools.

Always use common sense and pay particular attention to all the DANGER,
WARNING, CAUTION and NOTE statements in this manual.

This is the safety alert symbol. It is used to alert
you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid
possible injury or death.

DANGER indicates an imminently hazardous
situation which, if not avoided, will result in death
or serious injury.

WARNING indicates a potentially hazardous
situation which, if not avoided, could result in
death or serious injury.

TABLE OF CONTENTS

CONGRATULATIONS! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

GENERAL SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

RECOGNIZE SAFETY SYMBOLS, WORDS AND LABELS . . . . . . . . 2-3

IMPORTANT INFORMATION ABOUT THIS MANUAL . . . . . . . . . . . 4

UNPACKING & INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

SAFETY WARNINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6

GENERAL SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6

SAFETY RULES FOR PRESSURE WASHERS . . . . . . . . . . . . . . . . . . . . 6-10

GROUND-FAULT CIRCUIT - INTERRUPTER PROTECTION . . . . . . . 9

GROUNDING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-10

EXTENSION CORD USAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

FUNCTIONAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

PRESSURE WASHER TERMINOLOGY . . . . . . . . . . . . . . . . . . . . . . . . . 11

ASSEMBLY & SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-13

OPERATING THE PRESSURE WASHER . . . . . . . . . . . . . . . . . . . . . . . . 13-17

ATTACHING NOZZLES TO SPRAY WAND . . . . . . . . . . . . . . . . . . . . 15-16

SHUTTING DOWN PRESSURE WASHER . . . . . . . . . . . . . . . . . . . . 16

USAGE OF CLEANING DETERGENTS . . . . . . . . . . . . . . . . . . . . . . . 17

MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-19

TROUBLESHOOTING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-24

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

1 YEAR LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-28

CONGRATULATIONS!

Thank you for choosing this pressure washer. Our aim is to provide you with qual­ity professional products, and we want you to be totally satisfied with your product
and our Customer Service. If any help or advice is needed, please contact us at
1-888-278-8092. When properly cared for, this product will give you many years of
satisfaction.

1 2

For consumer questions or comments, please call 1-888-278-8 092.

Days/Hours of operation:
9am-7pm EST Monday - Friday
10am-6pm EST Saturday - Sunday

English and Spanish Speaking Customer Service Representatives are Available.

IMPORTANT INFORMATION ABOUT THIS MANUAL

Improper and unsafe use of this Pressure Washer can
result in death, fire and/or bodily injury. This instruction manual contains
important information about product safety. Keep the instruction manual
available for others to read before they use the Pressure Washer.

Improper maintenance and operation are responsible for the majority of accidents
involving Pressure Washers. The largest portion of these could be prevented by rec­ognizing the basic safety rules and precautions. Most accidents can be avoided if
the operator recognizes a potentially hazardous situation before it happens and by
observing appropriate safety rules and procedures as outlined in this manual.

Basic safety precautions are outlined in the SAFETY portion of this manual and
throughout the text in this manual where a potential hazard might occur.

Hazards that MUST be avoided to prevent serious injury follow headers marked DANGER

or WARNING. These same precautions are placed as labels on the tool itself.
NEVER use this Pressure Washer for applications that are NOT specified in this manual.

UNPACKING & INSPECTION

After opening the carton, unpack your new Pressure Washer and related parts &
accessories. Please inspect it carefully for any damage that may have occurred
during transit. If any parts are missing, please contact our Consumer Helpline:
Phone: [phone]

Do not operate this Pressure Washer if damaged during
shipment, handling or misuse. Damage may result in bursting, which can
cause serious injury or property damage. All damaged parts must be
repaired or replaced as needed prior to operating this Pressure Washer.

Check to see that all nuts, bolts and fittings are secure before putting this Pressure
Washer into service. If you have any questions, or require assistance with damaged
or missing parts, please contact our Consumer Helpline: Phone: [phone]

Please have the serial number, model number, date of purchase, and parts list (with
missing parts identified) available for reference when calling.

MODEL NUMBER:
SERIAL NUMBER:
DATE OF PURCHASE:

CAUTION indicates a potentially hazardous
situation which, if not avoided, may result in
minor or moderate injury.

CAUTION used without the safety alert symbol
indicates a potentially hazardous situation which,
if not avoided, may result in property damage.

NOTE provides additional information that is useful
for proper use and maintenance of this tool. If a NOTE
is indicated, make sure it is fully understood.

In addition to SAFETY ALERTS listed above, there could also be numerous symbols
alerting the operator that specific safety measures are required to safely operate this
tool. Learn these SAFETY SYMBOLS as well as the SAFETY ALERTS to prevent
injury to the operator and to bystanders.

READ OPERATING INSTRUCTIONS: Read and understand tool labels,
safety warnings and precautions in this manual before operating the tool.
Failure to follow WARNINGS could result in serious injury or even death
to the operator or bystanders.

ELECTRICAL SHOCK: This tool produces hazardous electrical voltage.
Read and become familiar with this manual’s WARNINGS and CAUTIONS
so that it is installed and used properly.

WEAR APPROVED EYE PROTECTION: Spray can splash back or propel
objects, including incorrectly attached accessories. Always wear
approved eye protection. Safety glasses must conform to the require­ments of American National Standards Institute (ANSI) Z87.1 and pro­vide protection against flying particles from both front and side.

INJECTION HAZARD: Pressure washers can produce fluid streams
severe enough to penetrate animal and human flesh.

SLIPPING and FALLING: Pressure washers produce puddles of slippery
liquid that can result in falls. Kickback from spray wand can result in falls
when using unstable platforms.

43

Always make sure the tool is in the OFF position when making adjustments,
changing parts, or performing any maintenance.

Service must be performed only by qualified repair personnel. Service or

maintenance by unqualified personnel may result in a risk of injury.
Do not use the tool if the power switch does not turn it “ON” or “OFF”. A tool that

cannot be controlled with the switch is dangerous and must be repaired.

Store all maintenance tools away from the immediate area before turning ON
the tool.

Do not overreach. Proper footing and balance is a must at all times while using

tools. Unstable support may lead to personal injury. Do not stand on the tool.
Serious injury could result if the tool tips over or you accidentally contact tool.

When using accessories, consult the owner’s manual provided by the manufactur­er. The use of improper accessories may cause risk of injury to yourself and others.

Keep protective guards in place and in proper working condition.
Maintain tools and equipment with care. They will function better and more

safely when kept clean and in good working condition. Keeping the tool clean,
dry, and free of grime will add to its life and performance.

Do not use the tool for applications other than specified.

SAFETY RULES FOR PRESSURE WASHERS

RISK OF INJURY
TO reduce the risk of injur

y, user must read and understand all

safety instructions and warnings at the beginning of this manual.

Pressure Washer produces fluid pressures and velocities high
enough to penetrate human and animal flesh which could result in
serious injury or amputation.

Ensure all connections are tightened securely. Inspect all hoses to ensure

they are not damaged or kinked. Loose connections or damaged hoses can
result in injection injuries.

Ensure all fittings are properly connected. Pull on connection to ensure fit­tings are secure. Improperly connected fittings can unexpectedly separate
resulting in injury.

SAFETY WARNINGS

READ ALL SAFETY WARNINGS BEFORE

USING PRESSURE WASHER.

GENERAL SAFETY RULES

People with electronic devices, such as pacemakers, should consult their
physician(s) before using this product. Operation of electrical equipment in close
proximity to a heart pacemaker could cause interference or failure of the pacemaker.

WARNING: This product contains chemicals known to the State of California to
cause cancer and birth defects or other reproductive harm.

Keep work area clean and well lit. Messy areas and cluttered workbenches
invite personal injury and/or property damage. Clear all work areas of unneces­sary tools, debris, furniture, etc.

Make sure the work area is well ventilated. Never operate in an enclosed area.
Do not place objects on top or against the tool.
Handle correctly. Always operate according to the instructions provided.

Never allow the tool to be operated by children, individuals unfamiliar with its
operation or unauthorized personnel.

Keep children and visitors away. All children should be kept away from the
work area. DO NOT let children handle the tool. Maintain a safe distance for any
person near the work area.

Childproof the workshop. The use of master switches and padlocks is highly
recommended. Remove starter keys where applicable.

Stay alert, watch what you are doing, and use common sense. Do not stand
on tool. Do not use tool while tired or under the influence of drugs, alcohol
or medication. A moment of inattention while operating the tool may result in

serious personal injury.

Operating any tools or equipment under the influence of drugs, alcohol, or
medication can cause personal injury to yourself and others.

Use the right tool. Use tools properly and for their intended task. Do not force

a small tool to do the job of a heavy-duty tool. Using the right tool to do the
right job will make doing the job safer.

65

NEVER cut or splice the power cord or extension cords.

DO NOT spray electrical apparatus and wiring.

WEAR rubber-soled tennis shoes or other footwear that provides some insula-

tion when operating the Pressure Washer.

COLD water use only.
FOR EITHER INDOOR OR OUTDOOR USE. Store indoors.

DO NOT direct spray toward electrical outlets, switches or products

connected to electrical service. Failure to observe this warning can
result in electrocution resulting in severe electrical shock or burns
and possibly resulting in death.

NEVER run the pressure pump without the water supply connected and turned
on. Non-repairable damage to the pump will occur.

RISK OF FALLING - Pressure washer can create puddles of slippery

solutions that can become hazardous.
ENSURE you stand on a stable surface while operating Pressure Washer. Initial

kickback from engaging spray wand can you to lose your balance and fall result­ing in minor to severe injuries.

USE EXTREME CAUTION if you must operate Pressure Washer from a ladder or
scaffolding. Kickback from spray wand can result to loss of balance and result
in a fall that could cause serious injuries.

WHEN cleaning Pressure Washer, ensure there are adequate slopes for drainage so
solutions don’t create puddles around unit that could result in slipping and falling.

RISK OF ELECTROCUTION:

Connect only to properly grounded outlet. Do not remove ground pin.
Inspect cord before using. DO NOT use if the cord is damaged.
Keep all connections dry and off the ground.

DO NOT touch plug with wet hands.
Connect to individual branch circuit only.
This product is provided with Ground Fault Circuit Interrupter built into the

power cord plug. If replacement of the plug or cord is needed, use only identi­cal replacement parts.

NEVER place hands in front of nozzle.

NEVER attempt to attach or remove spray wand or hose fittings while Pressure

Washer system is pressurized.

DO NOT treat fluid injection injuries as a simple cut. Seek immediate med­ical attention.

HIGH VELOCITY fluid spray can cause objects to break, propelling particles
at high speeds.

ALWAYS wear approved safety glasses when using or doing

maintenance on Pressure Washers.

ALWAYS wear protective clothing to prevent accidental spraying.

DO NOT permanently secure spray wand trigger in open position.

DO NOT use spray wand that does not have a trigger lock or trigger guard in

place and in proper working order.

DO NOT use acids, toxic or corrosive chemicals, poisons, insecticides, flamma­ble solvents or bleach with Pressure Washer. Use of these chemicals can result
in damage to equipment or serious injury or death.

RISK OF EXPLOSION - Do not spray flammable liquids.

RISK OF INJECTION OR INJURY to persons. Do not discharge stream at persons.

RISK OF INJECTION - Unit will start spraying when trigger is squeezed, if

“ON/OFF” switch is in “ON” position, point gun in safe direction.

GUN KICKS BACK - Firmly hold with both hands.

NEVER allow children to operate a Pressure Washer. Keep children at a safe

distance when an adult is using a Pressure Washer.

NEVER direct spray at Pressure Washer.

NEVER operate the Pressure Washer after it has tripped the GFCI or the main

circuit breaker unless the cause has been identified and resolved.

IF an extension cord must be used, keep the power cord connection out of
any standing water, and use a heavy duty three-wire properly grounded type.

Keep the connection as far away as possible from the item being washed and
any water runoff.

87

EXTENSION CORD USAGE

Use only 3-wire extension cords that have 3-prong grounding-type plugs and 3-pole
cord connectors that accept the plug from the product. Use only extension cords that
are intended for outdoor use. These extension cords are identified by a marking
“Acceptable for use with outdoor appliances; store indoors while not in use.” Use only
extension cords having an electrical rating not less than the rating of the product. Do
not use damaged extension cords. Examine extension cord before using and replace if
damaged. Do not abuse extension cord and do not yank on any cord to disconnect.
Keep cord away from heat and sharp edges. Always disconnect the extension cord
from the receptacle before disconnecting the product from the extension cord.

GROUND-FAULT CIRCUIT - INTERRUPTER PROTECTION

This Pressure Washer is provided with a Ground-Fault Circuit­Interrupter (GFCI) built into the plug of the power supply cord. This
device provides additional protection from the risk of electric
shock. Should replacement of the plug or cord become necessary,
use only identical replacement parts that include GFCI protection.

GROUNDING INSTRUCTIONS

In the event of a malfunction or breakdown, grounding provides a path of least
resistance for electric current to reduce the risk of electric shock. This tool is
equipped with an electric cord having an equipment-grounding conductor and a
grounding plug. The plug must be plugged into a matching outlet that is properly
installed and grounded in accordance with all local codes and ordinances.

Do not modify the plug provided - if it will not fit the outlet, have the proper outlet
installed by a qualified electrician.

Improper connection of the equipment-grounding conductor can result in a risk of
electric shock. The conductor with insulation having an outer surface that is green
with or without yellow stripes is the equipment-grounding conductor. If repair or
replacement of the electric cord or plug is necessary, do not connect the equipment­grounding conductor to a live terminal.

Check with a qualified electrician or service personnel if the grounding instructions
are not completely understood, or if in doubt as to whether the tool is properly
grounded.

Use only 3-wire extension cords that have 3-prong grounding plugs and 3-pole
receptacles that accept the tool’s plug.

Repair or replace damaged or worn cord immediately.

This tool is intended for use on a circuit that has an outlet that looks like the one
illustrated in Figure 1. The tool has a grounding plug that looks like the plug illus­trated in Figure 1. A temporary adapter, which looks like the adapter illustrated in
Figure 2, may be used to connect this plug to a 2-pole receptacle as shown in Figure
1 if a properly grounded outlet is not available. The temporary adapter should be
used only until a properly grounded outlet can be installed by a qualified electrician.
The green-colored rigid ear, lug, and the like, extending from the adapter must be
connected to a permanent ground such as a properly grounded outlet box.

9 10

UNGROUNDED AC OUTLET

GROUNDED AC OUTLET

GROUNDING ADAPTER

POWER CORD PLUG

POWER CORD PLUG

COVERPLATE

MOUNTING SCREW

GROUNDING PIN

GROUNDING PIN

GROUNDING

RIGID EAR

FIGURE 1

FIGURE 2

ASSEMBLY & SETUP

This Pressure Washer requires some assembly. If you have any problems with the
assembly of your Pressure Washer, please call the Pressure Washer helpline at
1-888-278-8092. If calling for assistance, please have the model, revision, and
serial number from the data tag available.

1. Using a box cutter, cut open the Pressure Washer carton
on top.

2. Carefully remove all items from the box and inspect for
completeness (see Functional Description).

HANDLE ASSEMBLY

Position handle into openings in Pressure Washer until
handle locks into place.

WAND/GUN CONNECTION

Insert the wand into the gun fitting outlet. Ensure
that the threads are aligned properly and that the
connection is secure. Securely tighten the nut by
hand.

PRESSURE HOSE/GUN CONNECTION

Unpack the pressure hose and connect the
metal fitting to the gun inlet. Ensure that the
threads are aligned properly and that the con­nection is secure. Securely tighten the nut by
hand. Place the gun into the gun holder on the
side of the Pressure Washer.

GARDEN HOSE / WASHER CONNECTION

DO NOT run the pressure washer without the water supply

connected and turned on. Damage to equipment resulting from failure to follow
this instruction will void warranty.

1. Before connecting the garden hose to the Pressure Washer, connect the garden
hose to the water source and run water through the hose to flush out any
debris. Shut off the water at the source.

2. Attach garden hose to the Pressure
Washer coupling inlet at the lower back
of the unit. Ensure that the threads are
aligned properly and that the connection
is secure. Securely tighten the nut by
hand.

3. Turn on the water source.

12

FUNCTIONAL DESCRIPTION

PRESSURE WASHER FEATURES:

1. Gun

2. Trigger Safety Lock

3. Trigger

4. Wand

5. Nozzle Connector

6. Nozzle Cleaning Needle

7. Handle

8. Gun Holder (Top)

9. High Pressure Hose

10. Spray Nozzles

11. On/Off Switch

PRESSURE WASHER TERMINOLOGY

Following are common terms associated with the use of Pressure Washers:
PSI: Pounds per square inch – common unit measure used for water pressure, air

pressure, hydraulic pressure and pounds of force.
GPM: Gallons per minute (liters per minute [metric]) – common unit measure used

for flow rate of water.

11

FRONT VIEW BACK VIEW

12. Front Casters

13. Folding Hose Reel Handle

14. Wheel Assembly

15. Detergent Tank

16. Water Inlet/Water Hose Connector

17. Locking Rear Wheels

18. Power Cord Hook

19. GFCI Power Cord

20. Power Cord Velcro Strap

2

3

13

El chorro de agua a alta presión que produce este equipo puede cortar la
piel y sus tejidos subyacentes causando una posible amputación.

La pistola rociadora acumula alta presión de agua, incluso cuando el motor está
detenido y el suministro de agua está desconectado, lo cual puede
causar lesiones.

El contragolpe proveniente de la pistola rociadora puede hacerlo caer.

1. For your protection, wear the protective safety glasses (provided).

2. Place the Pressure Washer near the working surface.

Make sure that the water source is turned on and all connections

to the Pressure Washer and Spray Gun are secure and without any water leakage.

3. Carefully remove the gun from its holder.

4. Completely unwind high pressure hose
from the hose reel.

5. Selecting the Right Nozzle for the Job.

To prevent damage to your surface and to select an
appropriate nozzle size for your application, always start with lowest pressure
nozzle size (Green) and continue changing to the higher nozzle size until the
best work result is achieved.

The Pressure Washer comes furnished with four spray nozzles. Each nozzle is color
coded and delivers a specific spray pattern and pressure for a particular cleaning
job. The size of the nozzle determines the size of the fan spray and the pressure out
of the nozzle.

0° Nozzle – Red: This nozzle delivers a pinpoint stream of pressurized water
and is extremely powerful. It covers only a small area of cleaning. This noz­zle should only be directed at surfaces that can withstand high pressure such
as metal or concrete. Do not use this nozzle to clean wood.

25° Nozzle – Green: This nozzle delivers a 25 degree spray pattern for
intense cleaning of larger areas. This nozzle should only be used on
areas that can withstand pressure from this nozzle.

Chemical Nozzle – Black: This nozzle is used to apply special chemicals
and cleaning solutions. This nozzle produces the weakest pressure
stream of the four nozzles.

4. Connect the Pressure Washer GFCI power cord to a
dedicated electrical outlet.

5. Press the RESET button on the GFCI to ensure its
proper operation.

Outlet capacity must be 120V, 60HZ and minimum 15 AMP.

For best result, use a short garden hose (30 ft. or less length),

cold water (less than 100 F) and adequate pressure (no less than 50 PSI).

POWER SUPPLY CONNECTION

KEEP all electrical connections dry and off the ground.

NEVER touch the plug with wet hands.

NEVER cut or remove grounding blade (round longer pin) on GFCI
attachment plug.

MANTENGA todas las conexiones eléctricas secas y separadas del piso.

NUNCA toque el enchufe con las manos mojadas.

NUNCA corte ni retire la clavija de puesta a tierra (pata redonda
más larga) en el enchufe de conexión del disyuntor GFCI.

OPERATING THE PRESSURE WASHER

ALWAYS wear approved safety glasses when operating Pressure
W

ashers. Spray can splash back or propel objects, including

incorrectly attached accessories.

The high pressure stream of water that this equipment produces can cut
through skin and its underlying tissues, leading to possible amputation.

Spray gun traps high water pressure, even when the motor is stopped
and water is disconnected, which can cause injury.

Kickback from spray gun can cause you to fall.

SIEMPRE use gafas de seguridad aprobadas al operar lavadoras a
presión. El chorro puede salpicar hacia atrás o expulsar objetos
incluyendo los accesorios incorrectamente instalados.

Press Reset

14

USAGE TIPS:

• For most effective cleaning, keep spray nozzle from 8 to 24 inches away from
cleaning surface.

• If you get spray nozzle too close, especially using high pressure mode, you may
damage surface being cleaned.

• DO NOT get closer than 6 inches when cleaning tires.

SHUTTING DOWN THE PRESSURE WASHER

The Pressure Washer motor runs only when the trigger is engaged. To shut off the
Pressure Washer:

1. Release spray gun trigger.

2. Move unit's ON/OFF switch to OFF position.

IMPORTANT: Releasing the trigger will shut off the motor but does not shut off
electrical power to the unit.

3. Remove and store quick change pressure washer tip.

4. Turn off water supply.

5. ALWAYS point spray gun in a safe direction and squeeze spray gun trigger to
relieve built up pressure in the unit.

Spray gun traps high water pressure, even when motor is

stopped and water is disconnected.

6. Engage trigger lock on spray gun when not in use. Place the gun in its holder
on the side of the unit.

7. Disconnect GFCI plug from outlet and wrap power cord around the Power Cord
Hook at the back of the pressure washer. Store the GFCI plug inside its housing
in the center of cord intake.

8. Disconnect pressure washer from water supply and store the unit (see MAINTE­NENCE section).

1615

Turbo Nozzle : This nozzle circulates a powerful spray into a
circular pattern to provide greater cleaning efficiency over
large areas.

ATTACHING NOZZLES TO SPRAY WAND

Never place hands in front of nozzle. Never grasp hose or fittings during
Pressure Washer operation. Never attempt to attach or remove spray wand or

hose fittings while Pressure Washer system is pressurized.
Turn off Pressure Washer and lock the Gun Trigger before attempting to
change pressure nozzles.

Nunca coloque las manos delante de la boquilla. Nunca tome la manguera
ni las uniones durante el funcionamiento de la lavadora a presión.

Nunca intente conectar ni retirar el tubo de rociado o las uniones de la
manguera mientras el sistema de la lavadora esté presurizado.
Apague la lavadora y trabe el gatillo antes de cambiar las boquillas a presión.

A.To attach, pull back on slip ring and insert nozzle

until it securly snaps into place.

B.To detach, slide down slip ring on female quick-

disconnect to eject the nozzle.

6. Hold the gun securely with both hands. Point the gun in a
safe direction. Make sure that the gun safety (the button
above the trigger) is unlocked and squeeze the trigger to
allow any air that is trapped inside the unit and hoses to
escape. Continue to squeeze the trigger until a steady
stream of water comes from the nozzle.

7. Turn on the ON/Off switch on the front of the
Pressure Washer. NOTE: Motor does not start until
trigger is pulled.

8. Point the gun in a safe direction and squeeze the
trigger to start motor and water flow.

When using Pressure Washer on
uneven surfaces, lock rear wheels to prevent unintended
movement.

Make sure wand is
SECURELY tightened to Gun. If the wand is
not securely locked into place, it could be
ejected under high pressure when operating
the gun, possibly causing injury or damage.

Cerciórese de que el
tubo esté FIRMEMENTE apretado en la
pistola. Si no está firmemente trabado en
su lugar, el tubo podría ser expulsado a alta
presión al operarse la pistola y posiblemente
causar lesiones o daños.

PUSH

SQUEEZE

Press ON

SLIP RING

MAINTENANCE

Regular maintenance will improve performance and extend life of Pressure Washer.
Pressure Washer’s warranty does not cover items that have been subjected to opera-

tor abuse or negligence. Only by maintaining Pressure Washer in accordance with
instructions in this manual will the full value of the warranty be honored.

Some adjustments will need to be made periodically to properly maintain the Pressure
Washer. All service and adjustments should be made at least one time each season. It
is important that the maintenance chart below be followed.

MOVING AND STORAGE

After each application or winter storage follow these instructions:

1. When finished using the Pressure Washer, you must first drain and rinse the
detergent tank.

2. Turn the machine OFF and squeeze the trigger to release the trapped pressure
inside of the machine.

3. Remove both the garden hose and pressure hose from the unit.

4. Turn ON the machine and allow it to run for 5 seconds. (This will clear out most
of the water trapped in the pump).

5. Unplug the machine and store in a dry, climate controlled environment.

NOTE: Do not store the machine or accessories in a place where the temperature could
drop below 40°F.

AFTER EXTENDED STORAGE

Scale deposits may form in the pump when it is not used for some time. This causes
the motor to hesitate or not start up at all.

1. Do not plug the unit into electrical outlet or connect the pressure hose to the unit.

2. Connect garden hose to the unit and allow the water to exit from high pressure
outlet for a few seconds to rinse the system.

3. Shut off the water.

4. Connect pressure hose to the gun and then lock hose safety device.

CONNECTIONS

Connections (fittings) on Pressure Washer, pressure hose, gun and spray wand should
be cleaned regularly and lubricated with non-water soluble grease to prevent leakage
and damage to the o-rings.

USAGE OF CLEANING DETERGENTS

TO APPLY DETERGENT:

1. Select a detergent/cleanser appropriate for the intended application.

2. Prepare detergent solution as recommended by the manufacturer.

3. Remove the detergent tank lid.

4. Fill tank with prepared detergent solution. A small funnel may help with this
task. Replace the detergent tank lid.

5. Select “Black” detergent dispencing quick change nozzle.

Detergent will NOT flow unless “Black” detergent nozzle is

used.

6. Pull spray gun trigger and apply detergent to a dry surface, starting at lower por­tion of area to be washed and work upward, using long, even, overlapping strokes.

Wetting the surface first is not recommended, as it dilutes

the detergent and reduces its cleaning ability.

7. Allow detergent to "soak in" for 3-5 minutes before washing and rinsing.
Reapply as needed to prevent surface from drying. Do Not allow detergent to
dry on surface (prevents streaking).

TO RINSE:

1. Remove the “Black” detergent nozzle and replace with the appropriate nozzle for
the application.

2. Keep the spray gun a safe distance from the area you plan to spray.

3. Apply a high pressure spray to a small area, and then check the surface for
damage. If no damage is found, it is okay to continue cleaning.

4. Start at the top of the area to be rinsed, working down with same overlapping
strokes as you used for washing and applying detergent.

Stop the unit by pressing the ON/OFF button.
Disconnect electrical plug.
Turn off water and depressurize unit by squeezing trigger.

CLEANING TIPS:

• Never leave the Pressure Washer unattended while it is plugged into an electri­cal outlet and while water is supplied to the equipment.

• Never use the Pressure Washer water inlet to siphon detergent or wax.

• If you have the nozzle too far away from the surface being washed, the cleaning
will not be as effective.

IMPORTANT: DO NOT get closer than 6 inches when cleaning.

17

18

TROUBLESHOOTING GUIDE

20

NOZZLE

The nozzles should be lubricated with non-water soluble grease or light oil regularly.
Clogging of the nozzles causes the pump pressure to build up too high and cleaning is
required.

1. Make sure Pressure Washer On/Off switch is
set to Off and spray gun trigger is locked.

2. Clear blockage in nozzle by inserting the nozzle
cleaning needle (provided) through center hole.

3. After cleaning, remove the needle from nozzle
and store for future use.

LUBRICATION

This Pressure Washer does not require any maintenance on the pump or motor.
Both assemblies are pre-lubricated and sealed, requiring no additional lubrication.

A small amount of oil leakage is normal. If oil leakage

persists or became worse, contact our customer service department.

WATER INLET SCREEN (FILTER)

The Pressure Washer is equipped with a water inlet
screen to protect the pump from foreign debris.

CAREFULLY remove debris from the screen using a
nonabrasive and dull object (finger or Q-Tip). Make sure
screen is not torn or broken.

Do not operate Pressure Washer without screen filter in

place. Impurities entering pressure pump can cause internal damage.

COOLING SYSTEM

The air louvers, located in and around the Pressure Washer housing must be kept
clean and free of any obstructions to ensure proper air cooling of the motor and
pump during operation.

19

SCREEN

Problem Probable Cause Solution

Unit will not start (when
trigger is depressed)

1. Unit is not turned on.

2. Loose or disconnected
plug.

3. GFCI has tripped.

4. Thermal Switch has
tripped.

5. No AC power at the
outlet.

6. Main voltage supply is
too low.

7. Extension cord is too
long or wire size too
small.

8. Defective ON/OFF
Switch.

9. Defective GFCI Plug.

10. Defective Gun.

1. Press ON/OFF Switch
into ON position.

2. Reconnect Plug.

3. Push reset button on
plug.

4. Allow to cool and
restart unit.

5. Main circuit breaker is
tripped or outlet is faulty.

6. Make sure main supply
voltage is adequate
(See specifications).

7. Remove extension cord
or use proper extension
cord (See instructions).

8. Call Customer Service:
1-888-278-8092.

9. Call Customer Service:
1-888-278-8092.

10. Turn off the unit.
Remove the Gun from
the high pressure hose.
Redirect the outlet to a
safe direction and
switch ON the unit. If
the unit starts and
water comes out of the
front, the Gun may
need to be replaced.
Call Customer Service:
1-888-278-8092.

TROUBLESHOOTING GUIDE

22

Problem Probable Cause Solution

AC outlet circuit breaker
trips

1. Circuit (outlet) over­loaded.

2. Extension cord is too
long or wire size too
small.

3. Nozzle partially
blocked causing
excessive pressure.

.

1. Make sure circuit is
rated at 15 amps or
greater and unit is
plugged into a
dedicated circuit.

2. Use proper extension
cord (see instruc­tions).

3. Clean Nozzle (see
instructions).

Motor stops suddenly

1. Extension cord is too
long or wire size too
small.

2. Thermal safety switch
has tripped due to
overheating and over­work.

1. Remove extension
cord or use proper
extension cord (See
instructions).

2. Make sure main sup­ply voltage corre­sponds to specifica­tions. Allow to cool
and restart unit.

Unit will not stop when
trigger is released

1. Gun/Hose Assembly is
defective.

1. Remove Wand from
the Gun and squeeze
trigger to ensure that
the water is coming
out of the front of the
Gun at a rate equal to
the Garden Hose. Call
Customer Service:
1-888-278-8092.

Unit begins to smoke

1. Overheated, over­loaded or damaged
motor.

1. Turn off unit and Call
Customer Service:
1-888-278-8092.

Trigger will not move

1. Gun Safety Lock in
engaged.

1. Release Safety Lock
(See instructions).

TROUBLESHOOTING GUIDE

21

Problem Probable Cause Solution

Gun/Hose - Leaking water

1. Loose fitting. 1. Tighten fittings. If per­sists, Gun/Hose will
need to be replaced.
Call Customer Service:
1-888-278-8092.

Pump is noisy

1. Pump is sucking air. 1. Make sure hoses and
fittings are air tight.
Turn off machine and
purge pump by
squeezing trigger gun
until a steady flow of
water emerges through
the nozzle.

No water coming out of
Wand

1. Clogged Nozzle.

2. Wand is attached

incorrectly.

3. Clogged filter.

4. Kink in the Garden

Hose or Hose is
wrapped on a storage
wheel.

5. Gun/Hose Assembly is

defective.

1. Clean Nozzle (See
instructions).

2. See instructions.

3. Clean filter (see
instructions)

4. Unwrap the Garden
Hose and lay it out flat
to ensure that there
are no kinks in the
Hose.

5. Remove Wand from
the Gun and squeeze
trigger to ensure that
the water is coming
out of the front of the
Gun at a rate equal to
the Garden Hose. Call
Customer Service:
1-888-278-8092.

TROUBLESHOOTING GUIDE

24

Problem Probable Cause Solution

Unit does not reach
maximum pressure or
pressure is irregular

1. Diameter of garden
hose is too small.

2. Water supply is
restricted.

3. Not enough inlet
water supply.

4. Garden Hose length
is too long.

5. Water supply is
over I00°F.

6. Water inlet filter is
clogged.

7. Water leaking from
either Hose or
Unit.

8. Pressure hose is
blocked or leaks.

9. Nozzle worn or not
correct size.

10.Gun or Hose fail­ure.

11.Pump sucking air
from hose connec­tions.

12.Pump, Unloader or
Valves are clogged
or worn.

1. Replace with a 5/8 inch
or larger garden hose.

2. Make sure garden hose
has no kinks, leaks and
blockage.

3. Open water source fully.

4. Shorten the length of
the Garden Hose. We
recommend a maximum
length of 25 to 50 feet
for City water supply
and 30 feet for Well
water supply.

5. Provide cooler water
supply.

6. Clean the Screen filter
(see instructions).

7. Stop water from
leaking before using
the unit or Call
Customer Service:
1-888-278-8092.

8. Clear blocks in pres­sure hose or replace
hose.

9. Replace nozzle.

10.Call Customer Service:
1-888-278-8092.

11.Make sure connection
fittings are properly
tightened.

12.Call Customer Service:
1-888-278-8092

TROUBLESHOOTING GUIDE

23

Problem Probable Cause Solution

No Detergent

1. “Black” detergent nozzle
is not being used

2. Detergent is too thick.

3. Damaged or clogged

detergent suction
tube.

4. Nozzle is clogged with
debris.

1. Use “Black” detergent
nozzle.

2. Dilute detergent.

3. Call Customer Service:
1-888-278-8092.

4. Unclog nozzle using
provided cleaning
needle.

Detergent Leak from inside
the unit or won’t hold
detergent

1. Disconnected or
Kinked Detergent Pick
up Tube.

2. Chemical Tank Nipple
Broken.

1. Call Customer
Service:
1-888-278-8092.

2. Call Customer
Service:
1-888-278-8092.

Leaking Oil from Pump

1. A small amount of
leakage is normal.

1. If leakage persists, Call
Customer Service:
1-888-278-8092.

Leaking water from
bottom of unit

1. Machine Inlet
connection is
defective.

1. Check the Machine
Inlet at the front of the
unit to ensure that
water is not leaking
from it. If the connec­tion is leaking, it will
have to be replaced.
Call Customer Service:
1-888-278-8092.

Spray wand leaks

1. Spray wand is not
properly attached.

1. See instructions.

Detergent Tank fills up with
water

1. Detergent Suction
Assembly is defective.

1. Call Customer Service:
1-888-278-8092.

WARRANTY PERFORMANCE

By purchasing this product, purchaser expressly acknowledges and agrees that
their sole and exclusive remedy under this warranty shall be strictly limited to the
repair or replacement of any covered nonconforming items or parts thereof provid­ed that any such nonconforming item and/or part is promptly returned to an author­ized Service Center within the applicable warranty period, with a written request by
purchaser to repair and/or replace the nonconforming item and/or part. We recom­mend that you keep the original product packaging in the event you need to ship the
unit. We suggest the package be insured against loss or in transit damage. When
sending your product, include your name, address, phone number, e-mail address,
dated proof of purchase (or copy) and a statement about the nature of the problem.
Warranty coverage is conditioned upon purchaser furnishing Alltrade with adequate
written proof that they are the original purchaser and of the original purchase date.
Parts returned, freight prepaid and insured, will be inspected and, at Alltrade's
option, repaired and/or replaced free of charge if it is found to be defective and sub­ject to warranty. Alltrade retains the sole discretion to determine whether any item
or part is nonconforming and, if so, whether the item and/or part will be repaired
and/or replaced. If the unit is repaired, new or reconditioned replacement parts may
be used. If Alltrade chooses to replace the product, it may replace it with a new or
reconditioned of the same or comparable design. The repaired or replaced unit will
be warranted under the terms of the remainder of the one year warranty period; cov­ered defective parts not subject to normal wear and tear or other exclusions will be
repaired or replaced, at Alltrade's option. During the warranty period, Alltrade will
be responsible for the return shipping charges. Alltrade's repair and/or replacement
of any nonconforming item and/or part thereof shall constitute fulfillment of all obli­gations to the purchaser. Alltrade shall not be responsible or liable for any expense,
including freight charges, or repairs made outside Alltrade's facility or an Alltrade
designated service, unless expressly agreed to by Alltrade in writing. Under no cir­cumstances shall Alltrade bear any responsibility for loss of the unit, loss of time or
rental, inconvenience, commercial loss, or consequential damages.

For the location of an Authorized Service Center nearest you, please call customer
service at 1-888-278-8092.

This warranty does not cover parts damaged due to normal wear, abnormal condi­tions, misapplication, misuse, abuse, accidents, operation, improper storage, or
freight damage. Parts damaged or worn by operation in dusty environments are not
warranted. Failure to follow recommended operating and maintenance procedures
also voids warranty.

DAMAGE TO THE PRODUCT RESULTING FROM TAMPERING, ACCIDENT, ABUSE,
NEGLIGENCE, FAILURE TO FOLLOW INSTRUCTIONS, UNAUTHORIZED REPAIRS
OR ALTERATIONS, DAMAGE WHILE IN TRANSIT TO OUR SERVICE FACILITY, USE
OF UNAPPROVED OR IMPROPER ATTACHMENTS OR ACCESSORIES, OR OTHER
CAUSES UNRELATED TO PROBLEMS WITH MATERIAL OR WORKMANSHIP ARE
NOT COVERED BY THIS WARRANTY.

26

SPECIFICATIONS

*Meets PWMA-PW101 test requirement.

1 YEAR LIMITED WARRANTY

Express and Exclusive Limited Warranty to Original Retail Buyer

Alltrade Tools LLC (hereinafter "Alltrade") expressly warrants to the original retail
purchaser of the accompanying SNAP-ON™ Pressure Washer and no one else all
parts of the product (except those parts referred to below which are specifically
excluded from such warranty (see Exclusions) to be free from defects in materials
and workmanship for a period of one year from the original date of purchase.

SPECIAL WARRANTY NOTE FOR COMMERCIAL OR RENTAL USE: The above
warranty for this SNAP-ON™ Pressure Washer shall be effective for only 90 days
from the original date of purchase if this tool is used for any COMMERCIAL OR

RENTAL PURPOSE.

The date of purchase shall be the date of shipment to the original purchaser, or the
date the original purchaser took possession, custody, or control of the product,
whichever occurred first. This warranty shall be null and void if the product or any
component thereof is modified or altered. This warranty does not apply to any other
product and/or component thereof manufactured or distributed by Alltrade, and
does not apply to products and/or components thereof designed, manufactured
and/or assembled by others, for which Alltrade makes no warranties whatsoever.

THERE ARE NO WARRANTIES, WHICH EXTEND BEYOND THE DESCRIPTION ON
THE FACE HEREOF.

25

MAXIMUM PRESSURE 2000 PSI*

MAX WATER FLOW 1.4 GPM*

VOLTAGE 120V / 60HZ

CURRENT 13A

DETERGENT TANK 1.2 LITER

ELECTRICAL CORD 35 FT.

PRESSURE HOSE 25 FT.

INLET WATER PRESSURE 40-60 PSI

(INCLUDING NEGLIGENCE) OR OTHERWISE, SHALL ALLTRADE'S AND/OR ITS
REPRESENTATIVE (S) LIABILITY EXCEED THE PRICE OF THE PRODUCT. All LIA­BILITY CONNECTED WITH THE USE OF THIS PRODUCT SHALL TERMINATE UPON
THE EXPIRATION OF THE WARRANTY PERIODS SPECIFIED ABOVE.

LIMITATIONS ON WARRANTY DISCLAIMERS

Some states do not allow limitations on how long an implied warranty lasts and
some states do not allow the exclusion or limitation of the incidental or consequen­tial damages, so part or all of the above limitations or exclusions may not apply to
you. This warranty gives you specific legal rights, and you may also have other
rights, which vary from state to state.

If your product is not covered by this warranty, please call our Customer Service
Department at 1-888-278-8092 for general repair information, and charges and the
location of your nearest authorized service facility.

28

Alltrade will not be liable for the following: labor charges, loss or damage resulting
from improper operation, maintenance or repairs made by other persons; pre-deliv­ery services such as assembly, oil and lubricants, and adjustment; maintenance
services that are normally required to maintain the product.

The use of other than genuine Snap-On™ Repair Parts will VOID the warranty.

WARRANTY DISCLAIMERS

EXCLUSION AND DISCLAIMER OF ALL OTHER EXPRESS WARRANTIES, GUAR­ANTIES AND/OR REPRESENTATIONS, EXCEPT FOR THE LIMITED WARRANTY
PROVIDED HEREIN, ALL OTHER EXPRESS WARRANTIES, GUARANTIES, AND/OR
REPRESENTATIONS BY ALLTRADE AND OR ITS REPRESENTATIVE(S) REGARDING
THE DESIGN, MANUFACTURE, PURCHASE, USE AND/OR OPERATION OF THE
PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER, REGARDLESS OF
WHETHER ANY SUCH WARRANTY, GUARANTY AND/OR REPRESENTATION,
WRITTEN OR ORAL, ARISES BY OPERATION OF LAW AND/OR EQUITY AND/OR BY
ANY ACT OR OMISSION OF ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE
BUYER, ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE
AND/OR ITS REPRESENTATIVES. PURCHASER KNOWINGLY AND WILLINGLY
WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS, CLAIMS AND/OR
CAUSE OF ACTION ARISING THEREFROM OR BASED THEREON. PURCHASER'S
SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE.

EXCLUSION AND DISCLAIMER OF ALL IMPLIED WARRANTIES, INCLUDING THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. NO WARRANTY, ORAL OR WRITTEN, OTHER THAN THE WARRANTY
LISTED HEREIN IS MADE WITH REGARD TO THIS PRODUCT. ALL WARRANTIES
AND/OR IMPLIED WARRANTIES, GUARANTIES AND/OR REPRESENTATIONS BY
ALLTRADE AND/OR ITS REPRESENTATIVE(S) REGARDING THE DESIGN, MANU­FACTURE, PURCHASE, USE AND/OR OPERATION OF THE PRODUCT OR ANY COM­PONENT THEREOF SOLD HEREUNDER, REGARDLESS OF WHETHER ANY SUCH
WARRANTY, GUARANTY AND/OR REPRESENTATION, WRITTEN OR ORAL, ARISES
BY OPERATION OF LAW AND/OR EQUITY AND/OR BY ANY ACT OR OMISSION OF
ALLTRADE AND/OR ITS REPRESENTATIVES. PURCHASER KNOWINGLY AND
WILLINGLY WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS, CLAIMS
AND/OR CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON.

PURCHASER'S SOLE AND EXCLUSIVE REMEDY IS AS STATED ON PRECEDING PAGES.

LIMITATIONS OF LIABILITY

IN NO EVENT SHALL ALLTRADE AND/OR ITS REPRESENTATIVE(S) BE LIABLE FOR
INDIRECT, INCIDENTAL, SPECIAL AND/OR CONSEQUENTIAL DAMAGES OF ANY
KIND ARISING OUT OF OR RELATED TO, DIRECTLY OR INDIRECTLY, ANY BREACH
OR PROVISION OF ANY AGREEMENT BETWEEN ALLTRADE AND/OR ITS REPRE­SENTATIVE(S) AND PURCHASER, AND WARRANTY HEREUNDER, AND/OR THE
EXISTENCE, DESIGN, MANUFACTURE, PURCHASE, USE AND/OR OPERATION OF
ANY ITEM(S) SOLD HEREUNDER EVEN IF ALLTRADE AND/OR ITS REPRESENTA­TIVE(S) HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH DAMAGES. IN NO
EVENT, WHETHER BECAUSE OF A BREACH OF CONTRACT, WARRANTY, TORT

27