SCH5617
Desktop System
Controller Hub with
Advanced, 8051µC-Based
Auto Fan Control
PRODUCT FEATURES
ACPI 2.0 Compliant
High Performance 8051
— 2.5X average instruction execution speed improvement
over the entire instruction set; i.e., typical 4-clock
instruction cycle in high-performance 8051 vs. 12-clock
instruction cycle in standard 8051.
— Faster clock speed: 32 MHz vs. 16 MHz in standard
8051.
— Dual Data Pointers
— More Interrupts: Power-Fail, External Interrupt 2,
External Interrupt 3, etc.
— A set of External Memory/Mapped Control Registers
provides the 80C51 core with the ability to directly
control many functional blocks of the SCH5617.
— 384 Bytes of RAM as part of the 8051 core
— 4k Bytes Data RAM (869 bytes may be used to patch
ROM code)
— Twelve Interrupt Sources
— Watch Dog Timer (WDT)
PECI Interface
Temperature Monitor
— Monitoring of up to Two Remote Thermal Diodes
— Supports temperature readings from -63 degrees to
+192 degrees
– Supports monitoring of discrete diodes (3904 type
diodes)
– Supports monitoring substrate diodes (45nm &
65nm processor diodes)
— 1/8th degree temperature resolution
— Internal Ambient Temperature Measurement
— Limit Comparison of all Monitored Values
PROCHOT_IN# Pin
— Mapped into Temperature monitoring interrupt
generation logic
— May be used to adjust fan control limits
— May be configured to force fans on full
PROCHOT_OUT Pin
Auto-Fan Control with ProcHot Features
— PWM (Pulse width Modulation) Outputs (3)
– Legacy PWM control dc fan outputs
— High Frequency PWM Options (15kHz up to 30kHz)
— 2 second delayed start-up for PWM outputs
— Fan Tachometer or Lock Rotor Inputs (3)
— Programmable linear automatic fan control based on
temperature
Data Brief
— Acoustic enhancement mode
— ProcHot pins modulate Tmin
— Fan PWM duty cycle is a function in linear mode of
multiple temperatures and ProcHot signals
— PWM Ramp Rate Closed Loop Control
Internal Ring Oscillator for VTR Powered Logic
Low Battery Warning
LED Control
SMBus Isolation Logic
Programmable Wake-up Event Interface
PC2001 Compliant
General Purpose Input/Output Pins (30 Host
controlled, 16 8051 controlled)
21 Dedicated Scratchpad registers
ISA Plug-and-Play Compatible Register Set
System Management Interrupt
GLUE Logic
— IDE Reset/Buffered PCI Reset Outputs
— Power OK Signal Generation
— Power Sequencing
— Power Supply Turn On Circuitry
— Resume Reset Signal Generation
— Hard Drive Front Panel LED
2.88MB Super I/O Floppy Disk Controller
— Licensed CMOS 765B Floppy Disk Controller
— Software and Register Compatible with SMSC's
Proprietary 82077AA Compatible Core
— Supports Two Floppy Drives
— Configurable Open Drain/Push-Pull Output Drivers
— Supports Vertical Recording Format
— 16-Byte Data FIFO
— 100% IBM® Compatibility
— Detects All Overrun and Underrun Conditions
— Sophisticated Power Control Circuitry (PCC) Including
Multiple Powerdown Modes for Reduced Power
Consumption
— DMA Enable Logic
— Data Rate and Drive Control Registers
— 480 Addresses, Up to Eight IRQs, and Four DMA
Options
— Enhanced Digital Data Separator
– 2 Mbps, 1 Mbps, 500 Kbps, 300 Kbps, 250 Kbps
Data Rates
– Programmable Pre compensation Modes
SMSC SCH5617 PRODUCT PREVIEW Revision 0.6 (01-09-08)
Desktop System Controller Hub with Advanced, 8051µC-Based Auto Fan Control
Keyboard Controller
— 8042 Software Compatible
— 8 Bit Microcomputer
— 2k Bytes of Program ROM
— 256 Bytes of Data RAM
— Four Open Drain Outputs Dedicated for
Keyboard/Mouse Interface
— Asynchronous Access to Two Data Registers and One
Status Register
— Supports Interrupt and Polling Access
— 8 Bit Counter Timer
— Port 92 Support
— Fast Gate A20 and KRESET Outputs
Serial Ports
— Two Full Function Serial Ports
— High Speed NS16C550A Compatible UARTs with
Send/Receive 16-Byte FIFOs
— Programmable Baud Rate Generator
– Supports all standard baud rates up to 115k bps
– Supports non-standard baud rates of 230k and
460k bps
— Modem Control Circuitry
— 480 Address and 15 IRQ Options
ORDER NUMBER:
Infrared Port
— Multi protocol Infrared Interface
— IrDA 1.0 Compliant
— SHARP ASK IR
— 480 Addresses, Up to 15 IRQ
Multi-Mode™ Parallel Port with ChiProtect™
— Standard Mode IBM PC/XT®, PC/AT®, and PS/2™
Compatible Bi-directional Parallel Port
— Enhanced Parallel Port (EPP) Compatible - EPP 1.7
and EPP 1.9 (IEEE 1284 Compliant)
— IEEE 1284 Compliant Enhanced Capabilities Port
(ECP)
— ChiProtect Circuitry for Protection
— 960 Address, Up to 15 IRQ and Four DMA Options
LPC Interface
— Multiplexed Command, Address and Data Bus
— Serial IRQ Interface Compatible with Serialized IRQ
Support for PCI Systems
— PME Interface
Power Good Output
3.3 Volt I/O
128 Pin QFP, Lead-Free RoHS Compliant Package
SCH5617-NS FOR 128 PIN, QFP LEAD-FREE ROHS COMPLIANT PACKAGE
80 ARKAY DRIVE, HAUPPAUGE, NY 11788 (631) 435-6000, FAX (631) 273-3123
Copyright © 2008 SMSC or its subsidiaries. All rights reserved.
Circuit diagrams and other information relating to SMSC products are included as a means of illustrating typical applications. Consequently, complete information sufficient for
construction purposes is not necessarily given. Although the information has been checked and is believed to be accurate, no responsibility is assumed for inaccuracies. SMSC
reserves the right to make changes to specifications and product descriptions at any time without notice. Contact your local SMSC sales office to obtain the latest specifications
before placing your product order. The provision of this information does not convey to the purchaser of the described semiconductor devices any licenses under any patent
rights or other intellectual property rights of SMSC or others. All sales are expressly conditional on your agreem ent to the terms and conditions of the most recently dated
version of SMSC's standard Terms of Sale Agreement dated before the date of your order (the "Terms of Sale Agreement"). The product may contain design defects or errors
known as anomalies which may cause the product's functions to deviate from published specifications. Anomaly sheets are available upon request. SMSC pr oducts are not
designed, intended, authorized or warranted for use in any life support or other application where product failure could cause or contribute to personal injury or severe property
damage. Any and all such uses without prior written approval of an Officer of SMSC and further testing and/or modification will be fully at the risk of the customer. Copies of
this document or other SMSC literature, as well as the Terms of Sale Agreement, may be obtained by visiting SMSC’s website at http://www.smsc.com. SMSC is a registered
trademark of Standard Microsystems Corporation (“SMSC”). Product names and company names are the trademarks of their respective holders.
SMSC DISCLAIMS AND EXCLUDES ANY AND ALL WARRANTIES, INCLUDING WITHOUT LIMITATION ANY AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE, TITLE, AND AGAINST INFRINGEMENT AND THE LIKE, AND ANY AND ALL WARRANTIES ARISING FROM ANY COURSE
OF DEALING OR USAGE OF TRADE. IN NO EVENT SHALL SMSC BE LIABLE FOR ANY DIRECT, INCIDENTAL, INDIRECT, SPECIAL, PUNITIVE, OR CONSEQUENTIAL
DAMAGES; OR FOR LOST DATA, PROFITS, SAVINGS OR REVENUES OF ANY KIND; REGARDLESS OF THE FORM OF ACTION, WHETHER BASED ON CONTRACT;
TORT; NEGLIGENCE OF SMSC OR OTHERS; STRICT LIABILITY; BREACH OF WARRANTY; OR OTHERWISE; WHETHER OR NOT ANY REMEDY OF BUYER IS HELD
TO HAVE FAILED OF ITS ESSENTIAL PURPOSE, AND WHETHER OR NOT SMSC HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Revision 0.6 (01-09-08) 2 SMSC SCH5617
PRODUCT PREVIEW
Desktop System Controller Hub with Advanced, 8051µC-Based Auto Fan Control
General Description
The SCH5617 is a 3.3V PC 2001 compliant Super I/O controller with an LPC interface. All legacy
drivers used for Super I/O components are supported making this interface transparent to the
supporting software. The LPC bus also supports power management, such as wake-up and sleep
modes.
The SCH5617 provides temperature monitoring with auto fan control. The temperature monitor is
capable of monitoring two external diodes, one internal ambient temperature sensor or retrieving
temperatures from external processors that implement the PECI Interface. This device offers
programmable automatic fan control support based on one or more of these measured temperatures.
There are three pulse width modulation (PWM) outputs with
fan tachometer inputs. In addition, there is support for a PROCHOT_IN# pin that may be used to
generate an interrupt, adjust the programmed temperature limits in the auto fan control logic, or force
the PWM outputs on full. There is also a separate PROCHOT_OUT output pin.
The GLUE Logic includes various power management logic including generation of RSMRST# and
Power OK signal generation. There are also four LEDs to indicate power status and hard drive activity.
Also included is SMBus Isolation logic, which can be used to isolate SMBus signals during power down
modes.
high frequency support as well as three
The part provides 46 General Purpose I/O control pins, which offer flexibility to the system designer.
There are 21 Scratchpad read/write runtime registers for custom use.
The SCH5617 incorporates the following Super I/O components: a parallel port that is compatible with
IBM PC/AT architecture, as well as the IEEE 1284 EPP and ECP; two serial ports that are 16C550A
UART compatible; a keyboard/mouse controller that uses an 8042 micro controller; two floppy
controllers, which use SMSC's true CMOS 765B core; one infrared port that is IrDA 1.0 compliant. The
true CMOS 765B core provides 100% compatibility with IBM PC/XT and PC/AT architectures and is
software and register compatible with SMSC's proprietary 82077AA core. The part also provides a low
battery warning circuit.
The SCH5617 is ACPI 1.0b/2.0 compatible supports multiple low power-down modes. It incorporates
sophisticated power control circuitry (PCC), which includes keyboard and mouse wake-up events.
The SCH5617 supports the ISA Plug-and-Play Standard register set (Version 1.0a). The I/O Address,
DMA Channel and hardware IRQ of each logical device in the SCH5617 may be reprogrammed
through the internal configuration registers. There are up to 480 (960 for Standard Mode Parallel
I/O address location options, a Serialized IRQ interface, and four DMA channels.
Port)
SMSC SCH5617 3 Revision 0.6 (01-09-08)
PRODUCT PREVIEW
Block Diagram
14.318 MHz
CLOCK
GEN
Desktop System Controller Hub with Advanced, 8051µC-Based Auto Fan Control
IDE_RSTDRV#*, PCI_RST_SYS#*
PCI_RST_SLOTS#*, PS_ON#*
PWR_GOOD_3V*, PWRGD_PS, RSMRST#*
Glue Logic
LEDs
SECONDARY_HD#*
PRIMARY_HD#*
SCSI#*
HD_LED#*
LED2*
LED3*
LED1*
SER_IRQ
PCI_CLK
LAD[3:0]
LFRAME#
LDRQ#
PCI_RESET#
LPCPD#
IO_PME#*
IO_SMI#*
GP10*, GP11*, GP15*, GP21*,
GP22*, GP23*, GP25*, GP26*,
GP31*, GP33*, GP35*, GP36*,
GP37*, GP40*, GP41*, GP42*,
GP52*, GP53*, GP55*, GP57*,
GO60*, GP61*, GP75*, GP76*,
GP77*, GP80*, GP81*, GP82,
GP83*, GP84*, GP8051_[12:1]*,
GP8051_[17:14]*
TACH1
TACH2
TACH3
HVSS
Remote1+
Remote1-
Remote2+
Remote2-
HVTR
PWM1
PWM2
PWM3
PROCHOT_IN#
PROCHOT_OUT
SERIAL
IRQ
LPC
Bus Interface
Power Mgmt
General
Purpose
I/O
Runtime
Registers
8051
ROM
Auto
Fan
Control
Analog
Interface
Analog
Block
(Data, Address, and C ontrol lines)
SMC PROPRIETARY
82077 COMPATIBLE
VERTICAL
FLOPPYDISK
CONTROLLER CORE
Internal Bus
SCH5617
(128 QFP)
WDATA
WCLOCK
RCLOCK
RDATA
DIGITAL DATA
SEPARATOR
WITH WRITE
PRECOM-
PENSATION
Multi-Mode
Parallel Port
with ChiProtect
High-Speed
16550A
UART
PORT 1
High-Speed
16550A
UART
PORT 2
SMBus Isolation
Circuits
Keyboard/Mouse
8042
controller
PD[7:0]
BUSY,SLCT,PE
ERROR#, ACK#
TM
STROBE#, INIT#
SLCTIN#
ALF#
TXD1*,RXD1*
CTS1#*, RTS1#*
DSR1#*, DTR1#*
DCD1#*, RI1#*
TXD2*,RXD2*
CTS2#*, RTS2#*
DSR2#*, DTR2#*
DCD2#*, RI2#*
SCLK*, SDAT*
SCLK_1*, SDAT_1*
KCLK, MCLK
KDAT, MDAT,
KBDRST#, A20M
P12*,P16*,P17*
PECI V
REF
PECI IO
PECI READY
PECI
Interface
MRT0#, MRT1#*, TRK0#,
INDEX#,WRTPRT#,WGATE#,
HDSEL#,DRVDEN0*,
DIR#, STEP#, DSKCH G#,DS0#, DS1#*
RDATA#,
WDATA#
Note 1: This diagram does not show power and ground
connections.
Note 2: Functions with "*" are loc ated on multifunctional
pins. This diagram is des igned to show the various
functions available on the chip (not pin layout).
Figure 1 SCH5617 Block Diagram
Revision 0.6 (01-09-08) 4 SMSC SCH5617
PRODUCT PREVIEW
Revision 0.6 (01-09-08) 5 SMSC SCH5617
Package Outline
Desktop System Controller Hub with Advanced, 8051µC-Based Auto Fan Control
PRODUCT PREVIEW
D
D1
3
e
R1
R2
GAUGE PLANE
0.25
REVISION
-
0°-7°
REVISION HISTORY
SEE SPEC FRONT PAGE FOR REVISION HISTORY
DATEDESCRIPTION
RELEASED BY
--
b
E1
3
D1/4
5
2
E
L1
4
L
DETAIL "A" (SCALE: 3/1)
E1/4
TOP VIEW
A2
SEE DETAIL "A"
C
A
c
SIDE VIEW
ccc C
SEATING PLANE
A1
3-D VIEW
NOTES:
1. ALL DI MENSIONS ARE IN MILLIMETER.
2. TOLERANCE OF THE TRUE POSITION OF THE LEADS IS ± 0.0 4mm MAXIMUM.
3. PACK AGE BODY DIMENS IONS "D1" AND "E1" DO NOT INC LUDE MOLD PROTRU SIONS. MAXIMUM MOLD PROTRUSION IS 0.25 mm.
4. DIMENSION "L" IS MEASURED AT THE GAUG E PLANE, 0.25mm ABOVE THE SEATING PLANE.
5. DETAILS ON PIN 1 IDENTIFIER AR E OPTIONAL BUT MUST BE LOCATED WITHIN THE ZONE INDICATED.
Figure 2 128-Pin QFP Package Outline (3.9mm footprint)
UNLESS OTHERWI SE SPECIFIED
DIMENSIONS AR E IN MILLIME TERS
AND TOLERA NCES ARE:
DECIMAL
X.X
±0.05
X.XX
X.XXX
±0.025
INTERPRET DIM AND TOL PER
ASME Y14.5M - 1994
MATERIAL
-
FINISH
-
PRINT WITH " SCALE T O FIT"
DO NOT SCALE DRAWING
ANGULAR
±1°±0.1
THIRD ANGLE PROJECTION
NAME DATE
DRAWN
S.K.ILIEV
CHECKED
S.K.ILIEV
APPROVED
S.K.ILIEV
80 ARKAY DRIVE
HAUPPAUGE, NY 11788
USA
TITLE
PACKAGE OUTLINE
128 QFP-14x20x2.7mm BODY-3.9mm FOOTPRINT
11/30/04
DWG NUMBER
11/30/04
11/30/04
MO-128 QFP-14x20-3.9FP
SCALE SHEET
STD COMPLIANCE
JEDEC: MO -112 (B) & MS-02 9 (A)
1:1
REV
C
-
Loading...