Page 1
Chest-type Freezer
Thank you for your trust and for buying this appliance.
We hope it will successfully serve the purpose for many years.
The chest-type freezer for domestic use is
intended for freezing of fresh articles of food and
for long-term storage of frozen food (up to one
year), depending on the kind of food.
The temperature in the interior is -18°C or lower.
Before Using .................................................. 36
Instructions for Use
We Care for the Environment
Energy Saving
Important....................................................... 37
Disposing of the Worn Out Appliance
Installation ..................................................... 38
Selection of Room
Cooling of the Appliance
Connection to the Mains Supply
Operating the Appliance .............................. 39
Temperature Selection
Red Light
ON/OFF Switch
Interior Light (on some models only)
Instructions for Use
Use................................................................... 41
Operation Modes
Switching on the Empty Freezer
Freezing of Fresh Foods
Storage of Frozen Foods
Frozen Food Defrosting
Cleaning and Maintenance........................... 43
Freezer Defrosting
Cleaning
Discontinued Service
Trouble-shooting Guide................................ 44
Interior Light Bulb Replacement
35
Page 2
Before Using
x Before connecting the appliance to the mains
supply, leave it to rest in its place for about 2
hours. In this way you reduce a possibility of
troubles occurring in cooling system due to
transport handling.
x Remove the two plastic spacers which are
situated under the lid and protecting the seal
against damages during transport.
x Clean the interior of the appliance with
lukewarm water into which you have added a
few drops of vinegar or baking soda (1
tablespoon per 1 liter of water).
Instructions for Use
These instructions for use are intended for the
user of the appliance.They describe the appliance
and its correct and safe use. They relate to
various types of freezers therefore you will find
among them also those functions which do not
apply to your appliance.
We Care for the Environment
substantially higher. To restore efficiency,
replace the gasket.
x The condenser on the rear wall should be
always clean, free of dust or any impurities.
x Always consider instructions stated in sections
Positioning and Energy Saving Tips, otherwise
the energy consumption is substantially higher.
x Our products use environmentally friendly
packaging, which can be either recycled or
disposed of in an environmentally friendly
manner. To this end, individual packaging
materials are clearly marked.
x These instructions are printed either on
recycled paper or chlorine free bleached paper.
x When your appliance finally wears out, please
try not to burden the environment with it; call
your nearest authorised service agent. (See
Disposing of the Worn Out Appliance)
Energy Saving
x Do not open the lid more frequently than it is
necessary as too frequent openings of the lid
cause temperature rises in the freezer,
excessive formation of frost and consequently
higher energy consumption.
x Take care not to leave the lid open too long,
particularly if the ambient air is hot and humid.
x It is recommendet to remove the frost layer
when it is 3 to 5 mm thick.
x Before loading the appliance with packages of
fresh foods, make sure they are cooled to
ambient temperature (except for the soup).
x If the termostat knob is set towards max (1), do
not forget turn it towards min (1) if intensive
cooling is no more necessary.
x If the gasket is damaged or if it turns out that
the sealing is poor, the energy consumption is
36
Instructions for Use
Page 3
Important
x If you have purchased a new appliance to
replace an old one which is equipped with a
lock that cannot be opened from inside (lock,
bolt), take care that the lock is made unfit. In
this way you will reduce a risk of children
getting in danger of being suffocated in the cell.
x Mind to connect the appliance correctly to the
mains supply.
x During the operation do not touch the cooled
surfaces of the appliance, especially not if your
hands are wet, because the skin might stick to
these very cold surfaces.
x Do not freeze up bottled drinks, especially not
fizzy ones such as mineral water, sparkling
wine, beer, cola etc., because the liquid
expands when freezing and the glass bottle
may explode.
x Avoid to eat frozen food (bread, fruit,
vegetables), because you can get frost burns.
x Carefully check the foods for color and smell
and if you are in doubt about their quality, throw
them away because they may be dangerous for
eating.
x You must disconnect the appliance from the
mains in the following cases:
before the repair (only a qualified technician
should repair it),
before cleaning,
before replacement of the light bulb.
x Do not defrost the appliance by means of
electric appliances (hair dryer etc.) and do not
scrap the frost layer with sharp tools.
x Use only enclosed tools or tools recommended
by the manufacturer.
x For the sake of environment protection - be
careful not to damage the rear wall of the
appliance (the condenser unit or the tubes - for
example when moving the appliance) or any
part of the refrigerating system inside the
appliance. Do not use sharp object for
defrosting the appliance. Use only enclosed
tools or tools recommended by the
manufacturer.
x The refrigerating system of the appliance is
filled with refrigerant and oil, so when the
appliance is damaged, handle it with care and
dispose it of in compliance with environmental
protecting precautions. (See We Care for the
Environment).
x Heating element incorporated in the applience,
all around the rim, is controlled by the operation
of the compressor and it prevents the door
gasket to freeze on to the freezer housing.
x In the supply cord is damaged, it must be
replaced by the manufacturer or his service
agent or a qualified person in order to avoid
hazard.
x The rating plate is placed in the interior wall or
on the back of the appliance.
Storage Time in Case of Defect or
Cutout of Power Supply
In case of defect or cutout of power supply, do
not open the freezer. If the power cut lasts more
than two days, empty the freezer and use the
foods or take care that they remain in frozen
condition.
Disposing of the Worn Out
Appliance
x When your appliance finally wears out, dispose
it of. If the appliance has a lock, break it, in
order to prevent eventual accidents (danger of
children get locked inside the appliance).
x The refrigerating system of the appliance is
filled with refrigerant and insulating substances
which should be separately treated and
processed. Call your nearest authorised service
agent or specialised servicing centre. If you
don't find one, contact your local authorities or
your distributor. Be careful not to damage the
tubes on the rear wall of the appliance (danger
of pollution).
Instructions for Use
37
Page 4
Installation
Selection of Room
Place the appliance in a dry well-aired room.
Allowed ambient temperature depends on the
model (class) of the appliance and ist stated on
the rating plate of the appliance.
Class Ambient temperature
SN (sub-normal) from +10°C to 32°C
N (normal) from +16°C to 32°C
ST (sub-tropical) from +18°C to 38°C
T (tropical) from +18°C to 43°C
Cooling of the Appliance
The appliance is not intended to be built-in the
kitchen cabinet.
Provide for enough space on either side of the
appliance (2-3 cm) for unobstructed air
circulation.
Cooling of the rear of the appliance is of special
importance.
x Freezers having the switches in the front, can
be pushed up to the wall as the hinges of the lid
define the minimum required distance
between the wall and the appliance.
x Freezers having the switches in the lid are
equipped with two spacers. Insert them into the
holes on the rear side in order to determine the
right distance of the appliance from the wall.
Do not place the appliance in wet cellar, on
balcony, near cooker, radiator, water heater and
similar and do not expose it to direct sunlight.
The appliance should be placed in horizontal
position on a firm base which remains stable
even after you have fully loaded the freezer.
Connection to the Mains Supply
Connect the appliance with the cable and plug to
the mains supply socket with a ground terminal
(safety socket).
Required nominal voltage and frequency are
indicated in the rating plate.
The connection to the mains supply and earthing
of the appliance have to be made according to
valid standards and regulations.
The appliance resists temporary voltage fluctuations but only in the tolerance of -15 to +10%.
38
Instructions for Use
Page 5
Operating the Appliance
The freezer is controlled by two switches and
thermostat knob. The switches are incorporated
in the front or in the lid of the freezer.
Switches (feature depends on the model)
I.
1 Red control light
2 ON/OFF switch
0 appliance switched off
I appliance switched on (the green light is on)
3 Operation mode selection switch
N automatic operation
S continuous operation (the yellow light is on)
Temperature Selection
When the freezer operates automatically, the
interior temperature is controlled by the
thermostat.
The thermostat is controlled by the thermostat
knob which is built-in the lower right part of front
or right side of the appliance. The knob is
protected against accidental setting changes
(children). You change the position of the
thermostat knob by inserting for example a coin
into the notch on the knob.
When the ambient temperature is normal, we
recommend medium setting.
Use higher settings only when required or
recommended.
We recommend to set the thermostat on
positions towards max (6) only in case when you
want to have accelerated cooling before
introducing a minor quantity of fresh foods or if
you want to adapt the operation mode to the
ambient temperature.
Thermostat settings towards min (1) are suitable
for energy saving mode provided that there is
stored a small quantity of foods in the freezer.
2
1 Red control light
2 ON/OFF switch
appliance switched off
appliance switched on (the green light is on)
3 Operation mode selection switch
automatic operation continuous operation (the
yellow light is on)
3
1
II.
2415 3
III.
1 Red control light
4 Green light
5 Yellow light
2 ON/OFF switch
appliance switched off (switch covers green light)
appliance is switched on (green light is on)
3 Operation mode selection switch
automatic operation (switch covers yellow)
lightcontinuous operation (yellow light is on)
NOTE!
Some versions enable switching off of the
appliance if the thermostat knob is turned to the
left over the min (1) position. In such cases turn
the knob slightly to the right on operating area.
Thermostat (feature depends on the
model)
I.
The most appropriate thermostat position is in the
middle between max (the coldest) and min (the
warmest).
II.
Higher settings on the knob (towards 6) mean
lower temperatures (colder) in the freezer.
Instructions for Use
39
Page 6
Red Light
The red light is on when the interior temperature
is not appropriate.
ON/OFF Switch
The switch is used for appliance switching on and
off. When the appliance is switched on the green
light is on.
Interior Light (on some models only)
The interior light is on when the freezer lid is
opened. It is on even the appliance is switched off
(green light off).
NOTE:
The appliance can be equipped with various
accessories depending on the model of the
appliance.
40
Instructions for Use
Page 7
Use
Chest frezer is used for frezing fresh foods and
storing frozen foods.
Operation Modes
By means of operation mode selection switch you
select one of the two operation modes:
continuous and automatic.
Continuous operation - the yellow
light is on.
The cooling systems operates continuously with
accelerated power.This mode is selected when
you want to freeze up bigger quantities of fresh
foods and when you wish deeply freeze already
frozen foods.
Automatic operation - the yellow
light is off.
The interior temperature is controlled by the
thermostat which turns the cooling system
operation on and off.
The frequency of switching the cooling system on
and off depends on:
the thermostat knob position (thermostat
setting),
frequency of the lid opening,
ambient temperature.
Switching on the Empty Freezer
Switch the appliance on and turn the operation
mode switch to continuous operation. All three
control lights are on. Introduce fresh foods into
the freezer a few hours after the red light went off.
x Foils and bags should be soft to fit tight to the
contents.
x Freezing containers should be tightly closed.
x The most important is that the food freeze in
the shortest possible period. Therefore it is
recommended that the packs are not too big
and that food is cooled down before putting into
the freezer.
1. Freezing procedure
x One day before freezing of foods place the
switch on the position for continuous operation
(yellow light is on). After that time you can
introduce fresh foods into the freezer.
x Approximately 24 hours after the last
introduction of fresh foods into the freezer, set
the switch to the position for automatic
operation (yellow light is off).
Freezing Capacity
The quantity of fresh foods which can be frozen at
one time in 24 hours is indicated in the rating plate.
If the quantity is bigger that the rated one, the quality
of freezing will be worse and the temperature of the
stored frozen foods will get higher.
2. Later Freezing of Fresh Foods
Repeat the freezing procedure 1. Care should be
taken that fresh foods do not get in direct contact
with already frozen packs.
3. Freezing Smaller Quantities of
Fresh Foods
If you wish to freeze up a small quantity of food
(1-2 kg), you do not need to place the switch on
the position for continuous operation.
Freezing of Fresh Foods
Proper use of the appliance, adequately packed
food, correct temperature and taking into account
hygienic precautions will substantially influence
the quality of freezing the food or storing of the
frozen foodstuffs.
Foods suitable for freezing and withstanding low
temperatures are to be selected.
x Food of high quality should be used.
x Only fresh fruit and vegetables should be
frozen.
x Put the foods in suitable packages and pack
them properly.
x Packages should be air and moisture tight
otherwise the contents could become dry as
well as vitamin losses could appear.
Storage of Frozen Foods
Operation mode selection switch is set to
automatic operation (yellow light is off).
Frozen Foods Storage Time
Frozen food storage time is the period in which a
frozen food still preserves its initial quality or
better the period in which microbiological and
biochemical deterioration has not occurred yet.
Storage times are different for different kinds of
food, subject to composition, quality and age of
individual foods.
The content of grease substantially shortens the
storage time. You can, for example, store lean
meat for 12 months while fatty meat can be
stored for 4 to 6 months only.
Instructions for Use
41
Page 8
Storage of Frozen Foods
The storage time of purchased foodstuffs is
indicated on their wrapping.
When shopping, mind to choose only such
foodstuffs which are suitably packed, furnished
with full data and stored in freezers with a
temperature not higher than -18°C.
Do not buy packs of food wrapped with frost. This
is an indication that such a pack has undergone
thawing.
x Protect the foodstuffs against defrosting.
x Temperature rise shortens the frozen food
storage time.
Frozen Food Defrosting
Use as soon as possible the foodstuffs that
started to thaw or that are already defrosted. Cold
preserves the food but it does not destroy
microorganisms which rapidly activate
themselves after defrosting to make foodstuffs
perishable.
Partial defrosting reduces the nutritional value of
foods, especially of fruits, vegetables and readymade meals.
42
Instructions for Use
Page 9
Cleaning and Maintenance
Freezer Defrosting
The inside surface of the freezer gets lined with
frost. Frost formation depends on frequency of
door opening and ambient humidity. It is
recommended to remove the frost layer after it
has reached a thickness of 3 to 4 mm.
x Approximately 24 hours before you intend to
defrost the freezer switch over the operation
mode switch to continuous operation (the
yellow light is on) so that the foods get deeply
frozen.
x After that period disconnect the appliance from
the mains supply.
x Remove frozen foods from the freezer and look
after that they do not get thawed.
x When defrosting and cleaning is completed
connect the appliance to the mains supply an
put the foods back in the freezer.
x Avoid using defrosting sprays, as they may
cause damage to the plastic parts and may be
hazardous to health.
The Fastest Way of Frost Removing
Use the supplied scraper and scrap the frost layer
from cooling surfaces and remove it from the
freezer with soft cloth before it thaws.
Cleaning
After you have defrosted the appliance, clean it.
x Before cleaning the appliance disconnect the
cable from the mains supply!
x Wash the inside surfaces with lukewarm water
into which you have added vinegar or baking
soda (one tablespoon per one liter of water).
Afterwards toroughly wipe the interior with clean
soft cloth.
x Clean the outside surfaces of the appliances
with soft cloth, water and detergent.
Varnished surfaces are cleaned with soft cloth
and an alcohol based cleaning agent (for
example glass cleaners). You may also use
alcohol (ethanol or isoprophylic alcohol).
The application of abrasive and specially
aggressive cleaners, such as the stainless steel
cleaners, is not appropriate for the cleaning of
plastic and coated parts.
x Clean the sealing of the lid with mild solution
of detergent and water.
x Dust the rear condenser unit from time to time
with a soft non- metal brush or vacuum cleaner
(at least once a year).
Discontinued Service
Frost Layer Defrosting
When the frost layer is too thick to be scraped, it
should be partially defrosted.
Remove the tap (1) from front of the appliance.
x Insert the pipe (2) into the hole and place a
receptacle under it in order to accumulate water
resulting from frost layer.
x Remove the tap (3) from the bottom of the
appliance.
x To speed up defrosting, leave the lid of the
appliance open. Remove larger pieces of the
layer with the scraper when they are no longer
stuck to the interior wall.
x After you have defrosted the appliance, put the
taps back and keep the pipe for further use.
x Disconnect the cable from the mains supply,
empty the foods, defrost and clean the interior.
x Place an uncovered small box of baking soda in
its interior an leave the lid slightly open.
x When the appliance is inoperative it can be
placed in a cold room as it withstands low
temperatures. Before putting it into operation
place it in warm room where it should rest for at
least 2 hours.
Instructions for Use
43
Page 10
Trouble-shooting Guide
During the service, the user come across troubles
appearing during the operation of the appliance.
cases result from improper handling of the
appliance and can be eliminated by yourself.
We are listing some of troubles, which in most
Trouble Cause Trouble-shooting
The appliance is connected No electricity in the wall socket.
to power supply, but won’t
work
The appliance operates The lid was opened for too long.
continuously. Thermostat knob is on too cold
Vibrations or too much noise. Inadequate position.
Outer surfaces are wet. Wet room.
Excessive formation of frost. The lid of the appliance opens too frequently or the lid is left open too long.
Red light is on. The appliance has not reached the set temperature.
The appliance is not switched on.
The thermostat knob was set
under min (1). position (towards
left) and the appliance was
switched off.
position.
Insufficiently cooled condenser.
The switch is in position for discontinuous operation (yellow light is on).
Appliance in direct contact with
wall or next units.
Badly isolated floor.
Longer period of hot and humid weather.
There is stored too big quantity of insufficiently cooled down foods.
Lid does not shut well.
Too big quantity of insufficiently cooled down foods raises the inside
temperature. As soon as the foods cool down to set temperature the light goes
off.
Switch it on (green light is on)
Turn the knob to the right.
Set the knob towards
min (1) position.
Remove the dust from the condenser and
check if theres is adequate air circulation
behind the appliance.
Take care for suitable pavement.
Move the freezer away.
Put the appliance in dry room.
Displace the appliance.
Check if two styrofoam elements are
removed and if packs eventually prevent
the lid to be closed.
Interior Light Bulb Replacement
Before you replace the light bulb, disconnect the
appliance from the mains.
Remove the plastic lid and replace the burnt out
bulb with a new one (E14, 15 W).
Do not throw the bulb among organic garbage.
Light bulbs belong to durables therefore
our in-guarantee service does not relate to it.
WE RESERVE THE RIGHT TO ALTER THE SPECIFICATIONS WHICH DO NOT
INFLUENCE ON THE APPLIANCE OPERATION.
44
Instructions for Use
Loading...