Contents
1. INSTRUCTIONS PROPER USE __________________________________________ 28
2. SAFETY INSTRUCTION ________________________________________________ 29
3. KNOW YOUR OVEN ___________________________________________________ 30
4. BEFORE FIRST USE___________________________________________________ 30
5. ELECTRONIC ANALOGUE CLOCK (ONLY ON SOME MODELS) _______________ 31
6. ELECTRONIC PROGRAMMER (ONLY ON SOME MODELS) ___________________ 33
7. OVEN CAVITY ________________________________________________________ 35
8. AVAILABLE ACCESSORIES_____________________________________________ 36
9. DESCRIPTION OF CONTROL ___________________________________________ 37
10. COOKING FUNCTION__________________________________________________ 40
11. OVEN TEMPERATURE CONVERSION CHART _____________________________ 44
12. COOKING CHART_____________________________________________________ 45
13. CLEANING AND MAINTENANCE _________________________________________ 46
14. SOMETHING WRONG? ________________________________________________ 49
15. INSTALLATION _______________________________________________________ 50
INSTRUCTIONS FOR THE USER: these contain user advice, description of the commands and the
correct procedures for cleaning and maintenance of the appliance.
INSTRUCTIONS FOR THE INSTALLER: these are intended for the qualified technician who must
install the appliance, set it functioning and carry out an inspection test.
27
Instructions for proper use
1. INSTRUCTIONS PROPER USE
ELECTRICAL CONNECTION: PLEASE REFER TO INSTALLATION INSTRUCTION FOR THE GAS
& ELECTRICAL SAFETY REGULATIONS AND THE VENTILATION REQUIREMENTS.
IN YOUR OWN INTEREST, AND THAT OF SAFETY, IT IS THE LAW THAT ALL GAS APPLIANCES
BE INSTALLED AND SERVICED BY COMPETENT PERSONS, WHO WILL COMPLY WITH THE
RELEVANT STANDARDS AND REGULATIONS.
CORGI REGISTERED INSTALLERS UNDERTAKE TO WORK TO SATISFACTORY STANDARDS.
DISCONNECTION OF GAS AND ELECTRIC APPLIANCES SHOULD ALWAYS BE CARRIED OUT
BY A COMPETENT PERSON.
THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND THEREFORE MUST BE KEPT
IN ITS ENTIRETY AND IN AN ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE
OVEN. WE ADVISE CAREFUL READING OF THIS MANUAL AND ALL THE INSTRUCTIONS
THEREIN BEFORE USING THE OVEN. INSTALLATION MUST BE CARRIED OUT BY QUALIFIED
PERSONNEL IN ACCORDANCE WITH THE REGULATIONS IN FORCE. THIS APPLIANCE IS
INTENDED FOR DOMESTIC USES AND CONFORMS TO CURRENT REGULATIONS IN FORCE.
THE APPLIANCE HAS BEEN BUILT TO CARRY OUT THE FOLLOWING FUNCTIONS: COOKING
AND HEATING-UP OF FOOD. ALL OTHER USES ARE CONSIDERED IMPROPER.
THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR IMPROPER USE.
NEVER USE THIS APPLIANCE FOR HEATING ROOMS.
DO NOT LEAVE THE PACKING IN THE HOME ENVIRONMENT. SEPARATE THE VARIOUS
WASTE MATERIALS AND TAKE THEM TO THE NEAREST SPECIAL GARBAGE COLLECTION
CENTRE.
THIS APPLIANCE IS MARKED ACCORDING TO THE EUROPEAN DIRECTIVE 2002/96/EC ON
WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE).
THIS GUIDELINE IS THE FRAME OF A EUROPEAN-WIDE VALIDITY OF RETURN AND
RECYCLING ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT.
DO NOT OBSTRUCT VENTILATION OPENINGS AND HEAT DISPERSAL SLITS.
THE I.D. PLATE WITH TECHNICAL DATA, REGISTRATION NUMBER AND BRAND NAME IS
POSITIONED VISIBLY ON THE OVEN DOOR FRAME.
THE PLATE MUST NOT BE REMOVED.
TO PREVENT ANY STEAM IN THE OVEN CREATING PROBLEMS, OPEN
THE DOOR IN TWO STAGES: HALF OPEN (5 CM APPROX.) FOR 4-5
SECONDS AND THEN FULLY OPEN. TO ACCESS FOOD, ALWAYS LEAVE
THE DOOR OPEN AS SHORT A TIME AS POSSIBLE TO PREVENT THE
TEMPERATURE IN THE OVEN FROM FALLING AND RUINING THE FOOD.
28
The manufacturer declines all responsibility for damage to persons or things caused by nonobservance of the above guidelines or by interference with any part of the appliance or by the use of
non-original spares.
Safety instruction
2. SAFETY INSTRUCTION
INSTRUCTIONS FOR THE INSTALLER: THESE ARE INTENDED FOR THE QUALIFIED
TECHNICIAN WHO MUST INSTALL THE APPLIANCE, SET IT FUNCTIONING AND CARRY OUT
AN INSPECTION TEST.
DO NOT ATTEMP TO MOVE THE APPLIANCE BY PULLING ON THE DOOR HANDLES. OPEN
THE DOOR AND GRASP THE FRAME OF THE OVEN TAKING CARE THAT THE DOOR DOES
NOT SHUT ON YOUR FINGERS.
IT IS OBLIGATORY FOR THE ELECTRICAL SYSTEM TO BE EARTHED ACCORDING TO THE
METHODS REQUIRED BY SAFETY RULES.
WHEN LINKING UP TO MAINS BY HARD WIRING, CONNECT BY MEANS OF A POWER CABLE
COMPLYING WITH APPLICABLE REGULATIONS.
THE SOCKET MUST BE ACCESSIBLE AFTER THE APPLIANCE HAS BEEN BUILT IN.
ALWAYS CHECK THAT THE CONTROL KNOBS ARE IN THE “ZERO” (OFF) POSITION WHEN
YOU FINISH USING THE OVEN.
NEVER PUT FLAMMABLE OBJECTS IN THE OVEN: THEY COULD BE ACCIDENTALLY LIGHTED
AND IGNITED CAUSE FIRE.
PARTS OF THE APPLIANCE MAY BE HOT DURING OR IMMEDIATELY AFTER USE. CARE
SHOULD BE TAKEN TO AVOID TOUCHING HEATING ELEMENTS INSIDE THE OVEN. ALLOW
SUFFICIENT TIME FOR THE APPLIANCE TO COOL AFTER SWITCHING OFF.
THE OVEN IS DESIGNED FOR USE BY ADULTS. DO NOT ALLOW CHILDREN TO GO NEAR OR
PLAY WITH IT.
THE APPLIANCE BECOMES VERY HOT DURING USE. SUITABLE HEAT-PROOF GLOVES
SHOULD BE WORN FOR ALL OPERATIONS.
DURING COOKING, DO NOT COVER THE BOTTOM OF THE OVEN WITH ALUMINIUM, TIN FOIL
OR GREASEPROOF PAPER AND DO NOT PLACE PANS OR OVEN TRAYS ON IT AS THIS MAY
DAMAGE THE ENAMEL COATING.
BEFORE THE APPLIANCE IS PUT INTO OPERATION, ALL THE LABELS AND PROTECTIVE
FILMS APPLIED INSIDE OR OUTSIDE MUST BE REMOVED.
DO NOT PLACE PLASTIC PRODUCTS OR PRODUCTS WITH PLASTIC PARTS INSIDE THE
OVEN. IF ACCIDENTALLY LEFT INSIDE THEY MAY BE A SOURCE OF SERIOUS DANGER TO
THE USER AND PUT THE APPLIANCE’S OPERATION AT RISK.
BEFORE CLOSING THE OVEN DOOR, MAKE SURE THAT ALL THE SHELVES AND TRAYS
PROVIDED HAVE BEEN PUSHED FULLY INTO PLACE SO THAT THEY DO NOT TOUCH THE
GLASS WHEN THE DOOR IS CLOSED.
IMMEDIATELY AFTER INSTALLATION CARRY OUT A BRIEF INSPECTION TEST OF THE OVEN,
FOLLOWING THE INSTRUCTIONS. SHOULD THE APPLIANCE NOT FUNCTION, DISCONNECT IT
FROM THE SUPPLY AND CALL THE NEAREST TECHNICAL ASSISTANCE CENTRE.
NEVER ATTEMPT TO REPAIR THE APPLIANCE. ALL REPAIRS MUST BE CARRIED OUT BY AN
AUTHORISED ENGINEER OR AT AN AUTHORISED SERVICE CENTRE.
29
3. KNOW YOUR OVEN
Instructions for the user
FRONT CONTROL PANEL
OVEN CAVITY
OVEN FAN
OVEN LIGHT
OVEN DOOR
DOOR HANDLE
OVEN GUIDE FOR SHELF
AND PAN
COOLING SYSTEM
The appliance is equipped with 2 cooling fans which come into operation when
the oven is switched on. Operation of the fan generates a normal flow of air
which comes out at the bottom, in the centre of the front of the oven, and may
continue for a short time even after the oven is switched off.
4. BEFORE FIRST USE
Do not leave the packing in the home environment. Separate the various waste materials and take
them to the nearest special garbage collection centre.
Before using the oven for the first time, pre-heat it to maximum temperature long enough to burn any
manufacturing oily residues which could give the food a bad taste.
HOW TO PROCEED
Remove all the accessories from the inside of the oven.
Remove all the removable label and any protective foils from the outside and the inside of the oven.
To switch on the oven at first use or after a power black-out, simply press the programmer central key
for 1 to 2 seconds to enable cooking in the large oven. The small oven does not require any specific
switch-on procedures: simply turn the thermostat knob to any setting.
Set the function knobs on the symbol
turn the thermostat knob on the symbol
and the thermostat knob to 250°C. For the small oven simply
.
30
Instructions for the user
5. ELECTRONIC ANALOGUE CLOCK (ONLY ON SOME MODELS)
The programmer user instructions are valid only for the large oven.
LIST OF FUNCTIONS
MINUTE-MINDER BUTTON
AUTOMATIC DURATION / AUTOMATIC STAR TIME BUTTON
TIME SETTING AND RESET
DECREASE TIME BUTTON
INCREASE TIME BUTTON
5.1 Setting the time
When the oven is used for the first time, or after a power failure, the display flashes on and off at
regular intervals. Press the
the current time. Press the
key for 1 to 2 seconds to stop the display flashing and start setting of
or keys to increase or decrease by one minute each time a key is
pressed.
Press one of the two value modification keys until the current time appears. The clock will start from
the time set 6/7 seconds after the last key is pressed.
At the end of each programmed cooking operation, an intermitant alarm will sound 3 to 4 times at
intervals of about 1 and a half minutes. The beeps can be stopped at any moment by pressing any
key.
5.2 Minute-minder
This function does not stop cooking but just triggers the alarm.
- When the
key is pressed the display illuminates, appearing as shown in
figure 1;
- Press the
or keys within 6 to 7 seconds to set the minute-minder.
Whenever a key is pressed, 1 outside segment, representing 1 cooking
minute will light up (figure 2 shows 10 cooking minutes).
- The countdown will start 6 to 7 seconds after the last key is pressed; at the
end of it, you will hear the alarm.
1
- During cooking with countdown, the current time can be displayed by
pressing the
key once; press again to return to the minute-minder display.
- At the end of the countdown, the oven has to be switched off by hand,
by turning the thermostat and the function selector to 0.
2
31
5.3 Programming
Cooking duration time: the 2
Instructions for the user
nd
button can be used to set the cooking time. Before setting it, turn
the thermostat to the cooking temperature of choice and the function selector knob to any setting. To
set the cooking time, proceed as follows:
- Press the
key for 1 to 2 seconds; the pointer will move to 12 o’clock (Fig.
1).
- Use the
and keys to set the cooking time; whenever the key is
pressed, 1 minute will be added to the cooking time, and every 12 minutes a
new inside segment will light up (figure 2 shows a cooking time of 1 hour).
- Once the required time has been set, cooking will start about 6 seconds after
the last time the
. key is pressed. or
1
- Once cooking has started, the display will show the current time,
represented by the constantly on segments, and the minutes left until
cooking finishes, represented by the flashing segments (every flashing
segments indicates 12 minutes of cooking time left).
- When the end of the cooking time is reached, the timer will switch off the
2
oven heating elements, the alarm will start and the numbers on the dial will
flash.
- The cooking time can also be reset by deleting the program set; pressing the
central key
for 1 or 2 seconds will delete the time set and the oven will
have to be switched off by hand.
Caution: cooking times of more than 6 hours cannot be set.
Cooking start: as well as setting a cooking duration time, the user can also set the cooking start time
(up to 12 hours after the current time). To set the cooking start/end time, proceed as follows.
- Set the cooking duration time as described in the previous point.
- Within 6 to 7 seconds after the last time the or keys are pressed, press the key to set
the cooking start time. The display will show the current time with the inside segments indicating
the cooking end time illuminated. Use the
and keys to set the cooking start time.
- 6 to 7 seconds after the last time a key is pressed, the display will show the current time and the
cooking start and end times, indicated by the illuminated inside segments. The segments on the
display will be constantly on until the current time is the same as the cooking start time. As soon
as the current time reaches the cooking start time set, all the inside segments will start to flash,
indicating that the oven has started cooking.
- When the end of the cooking time is reached, the timer will switch off the oven heating elements,
the alarm will start and the numbers on the dial will flash.
- To reset the entire program, keep the central key pressed for 1 or 2 seconds: if cooking has
already started the oven will have to be switched off by hand.
- The image on the right shows an example of programming: the current time
is 7.06 and cooking is programmed to start at 8 o'clock and finish at 9.
- At 8 o'clock, the inside segments between 8 and 9 will start to flash and the
hour pointer will remain still.
Caution: for the oven to start cooking after the programming procedure just described, the
thermostat and function selector must be properly set on the temperature and function
required.
5.4 "DEMO" Function
Models with analogue/digital programmer feature a "DEMO" function which deactivates the heating
elements while leaving the other functions unchanged. To activate it, simply press the
, , and
keys and keep them held down for 3-4 seconds. A confirmation buzzer will inform the user that the
function is active. When the “DEMO” function is active, the number 6 on the clock flashes at regular
intervals. To deactivate it, simply repeat the same procedure.
32
Instructions for the user
When using the oven for the first time, or after a power failure, the display flashes regularly and
6. ELECTRONIC PROGRAMMER (ONLY ON SOME MODELS)
The programmer user instructions are valid only for the large oven.
LIST OF FUNCTIONS
MINUTE MINDER BUTTON
COOKING DURATION BUTTON
END-OF-COOKING BUTTON
DECREASE TIME BUTTON
INCREASE TIME BUTTON
6.1.0 Clock adjustment
indicates
changes the time by 1 minute either up or down.
. Press the keys and at the same time the keys or : each single press
Before setting the programmer activate the desired function and temperature.
Use this setting to automatically start and stop the oven.
6.1.1 Semi automatic cooking
Use this setting for automatic oven switch-off at the end of cooking time. By pressing key
display lights up, showing
set the cooking time.
Release key
together with symbols A and
6.1.2 Automatic cooking
By pressing key
time, press keys
By pressing key
the same time, press keys
Release key
symbols A and
After set-up, to see the cooking time remaining, press the key ; to see the end of cooking time press
the key .
Set-up with incoherent values is logically prevented (e.g. the contrast between a cooking time and a
longer period will not be accepted by the programmer).
to start the programmed cooking time count. The display will now show the right time
, the display lights up showing ; keep the key pressed and at the same
or to set the cooking time.
the sum of the right time + cooking time will appear; keep the key pressed and at
to start the programmed count and the display will show the right time together with
.
; keep the key pressed and at the same time, press keys or to
.
or to regulate the end of cooking time.
, the
33
6.1.3 End of cooking
Instructions for the user
When cooking is over, the oven will automatically switch off and, at the same time, an intermittent
alarm will sound. After switching off the alarm, the display will once again show the right time together
with the symbol
6.1.4 Adjusting alarm volume
, indicating that the oven has returned to manual operation mode.
The acoustic alarm has three different settings. These can be operated, while the alarm is sounding,
by pressing key
.
6.1.5 Switching off the alarm
The alarm switches off automatically after seven minutes. It can be manually de-activated by pressing
the keys
6.1.6 Minute Counter
The programmer can also be used as a simple minute counter. By pressing key
and together.
, the display shows
; keep the key pressed and at the same time press keys or . On releasing the key ,
programmed counting will begin and the display will show the current time and the symbol
.
After set-up, to see the remaining time, press the key .
Use as a minute counter does not interrupt functioning of the oven at the end of the programmed time.
6.1.7 Cancellation of set data
Once the programme has been set, keep the key of the function to be cancelled pressed, while at the
same time
is reached by means of variation keys or . Time cancellation will be
considered as end-of-cooking time by the programmer.
6.1.8 Changing the set data
The cooking data entered can be changed at any time by keeping the function key pressed and at the
same time adjusting the keys
or .
34
Instructions for the user
7. OVEN CAVITY
GRILL
UPPER HEATING ELEMENT
ROOF
OVEN LIGHT
Large oven: it comes on when the
function switch knob is turned to any
position.
Small oven: rotate the temperature
knob clockwise to the first setting
aligned with the lamp symbol (
). The
light will remain on throughout entire
oven operation.
SELF CLEANING PANEL
OVEN GUIDE FOR SHELF AND PAN
LOWER HEATING ELEMENT
OVEN FAN
VENTILATED HEATING ELEMENT
35
8. AVAILABLE ACCESSORIES
The large oven has 4 supports for positioning plates and racks at
various heights and has upper protection.
The small oven has 3 supports.
Some models do not feature all accessories.
Oven shelf: useful for holding cooking vessels.
Grill rack: for placing above plate for cooking foods that might drip.
Grill pan: useful for catching fat from foods on the grill above.
Pastry plate: for baking cakes, pizza and oven desserts.
Instructions for the user
Roof liner/Grill guard: removing this simplifies cleaning procedures
inside the oven.
Chromium-plated tubular gripper for removing hot racks and plates from the oven.
Accessories available on request
Original accessories may be ordered from any Authorised Service Centre.
36
9. DESCRIPTION OF CONTROL
Instructions for the user
Large oven function knob
Large oven thermostat indicator light
Small oven thermostat indicator light
Small oven variable grill knob
Large oven thermostat knob
Clock and electronic programmer
Small oven thermostat knob
37
Turn the knob in either direction onto one of the following symbols:
9.1 Large oven function knob
NO FUNCTION SET
UPPER AND LOWER HEATING
ELEMENT: using the upper and the lower
elements is ideal for all types of cooking.
It is also suitable for re-heating dishes
prepared in advance.
GRILL ELEMENT: for grilling meat,
toasting or browining dishes.
LOWER HEATING ELEMENT: This
function is recommended when blindbaking pastry or cooking pizza. It may
also be used to finish off quiches or flans
to ensure the base pastry is properly
cooked.
UPPER AND LOWER HEATING
ELEMENT + VENTILATED HEATING
ELEMENT: This function is
recommended for cooking different types
of food (meat, fish, vegetables and cakes)
simultaneously on different shelves.
DEFROSTING: The flow of air produced
by the fan ensures quicker defrosting. The
air circulating inside the oven is at room
temperature.
9.2 Large oven thermostat knob
Instructions for the user
UPPER AND LOWER HEATING
ELEMENT + VENTILATION: This
function is recommended for cooking
cakes and bread on just one shelf.
WIDE GRILL ELEMENT +
VENTILATION : For rapid browning of
foods for grilling, such as meat or fish.
Recommended for large-sized items.
VENTILATED HEATING ELEMENT: the
air inside the oven is heated by the
element around the fan situated behind
the back panel. The fan circulates hot air
to maintain an even temperature inside
the oven. Select any temperature
between 50°C and 250°C. This function is
recommended for cooking different types
of food (meat, fish, vegetables and cakes)
simultaneously on different shelves.
GRILL ELEMENT + VENTILATION : For
rapid browning of foods for grilling, such
as meat or fish
LOWER HEATING ELEMENT +
VENTILATION: This combination
completes cooking more quickly of foods
that are ready on the surface, but require
more cooking inside, without further
browning. Suitable for any type of food.
Select the cooking temperature by turning the thermostat knob in the direction shown in the diagram,
to a setting between 50° and 250°C.
38
Instructions for the user
Set to the required temperature, between 50° and 250°C. The oven is switched on by turning the
9.3 Small oven thermostat knob
knob clockwise to any one of the following functions except the oven light:
No function set
OVEN LIGHT
No element engaged
UPPER AND LOWER HEATING
ELEMENT: This way used the upper and
the lower elements and is ideal for all type
of cooking. It is also suitable for re-heating
dishes prepared in advance.
LOWER HEATING ELEMENT: this
function is used when blind-baking pastry
or cooking pizza. It may also be used to
finish off quiches or flans to ensure the
base pastry is cooked enough.
GRILL ELEMENT: for grillin meat,
toasting or browning dishes.
WIDE GRILL ELEMENT: for grillin meat,
toasting or browning dishes.
Recommended for large-sized items.
9.4 Small oven variable grill knob
When this light comes on, the oven is heating up.
Position the small oven thermostat knob on the symbol
Turn the grill temperature selector knob in the direction shown in the diagram to the setting of choice.
The thermostat will turn on and off to maintain the selected temperature. When the
thermostat turns, on the light will glow.
9.5 Thermostat indicator light
When this light goes out, the preset heating temperature has been
reached.
When the light flashes, the temperature inside the oven is steady at
the set temperature.
or .
39
Ideal for all types of cooking, especially baking, fish,
10. COOKING FUNCTION
UPPER AND LOWER HEATING ELEMENT
Keep the oven door closed during cooking.
terrines and vegetable based dishes.
To ensure even heat distribution, we recommend you
cook on one level only.
Preheating is recommended in particular when baking
cakes and pizza.
Instructions for the user
This cooking mode is recommended for cuts of meat
How to cook?
LARGE OVEN: Set the function knob on the symbol
and use the thermostat knob to select the temperature
between 50°C and 250°C.
SMALL OVEN: Turn the small oven thermostat knob to
between 50°C and 250°C
WIDE GRILL ELEMENT
GRILL ELEMENT
Keep the oven door closed during grilling. Grilling
with the door open could permanently damage the
oven and affect safety of operation.
(pork chops, sausages, etc.) which stay tender and juicy,
and for toasting or for browning toppings on prepared
dishes, preferably hot.
How to cook?
40
LARGE OVEN: Set the large oven function knob on the
results, place the pan in the highest guide (4-3 for the
large oven / 2-3 for the small oven). For short-term
cooking of small quantities, place the grid in the fourth
guide from the bottom. For long-term cooking and grills,
put the grid in the lowest guide suitable for the size of the
food.
SMALL OVEN: Turn the small oven thermostat knob to
the
be cooked) and set the power using the variable grill
knob.
Cooking time depends on the thickness of the meat
not on its weight.
symbol and the thermostat knob on . For best
or symbol (depending on the amount of food to
Instructions for the user
LOWER HEATING ELEMENT
Keep the oven door closed during cooking.
This function is recommended when blind-baking pastry
or cooking pizza. It may also be used to finish off quiches
or flans to ensure the base pastry is properly cooked.
Preheating is recommended in particular when baking
cakes and pizza.
How to cook?
LARGE OVEN: Set the function knob on the
and use the thermostat knob to select the temperature
between 50°C and 250°C.
SMALL OVEN: Set the small oven function knob on the
symbol
symbol.
41
VENTILATED HEATING ELEMENT
UPPER AND LOWER HEATING ELEMENT +
VENTILATION
LOWER HEATING ELEMENT + VENTILATION
UPPER AND LOWER HEATING ELEMENT +
VENTILATED HEATING ELEMENT
Instructions for the user
Keep the oven door closed during cooking.
Dishes can be cooked on one or several shelves using the
fan oven. The hot air circulation produces an even
cooking temperature. Fan oven cooking is recommended
for all types of dishes.
In fan-assisted mode preheating should be carried out at
How to cook?
30/40°C above the cooking temperature. This
considerably shortens cooking times and reduces power
consumption, as well as giving better cooking results.
Set the function knob on the
use the thermostat knob to select the temperature
between 50°C and 250°C.
Fan oven cooking generally requires a lower temperature
than conventional cooking.
The fan oven has even heating on all runner positions.
This means that batches of the same food can be cooked
in the oven at the same time.
However, the top shelf may brown slightly quicker than the
lower one. This is quite usual. There is no mixing of
flavours between dishes.
/ / / symbol and
42
Instructions for the user
WIDE GRILL ELEMENT + VENTILATION
GRILL ELEMENT + VENTILATION
Keep the oven door closed during grilling.
Fan grilling offers an alternative method of cooking food
items normally associated with conventional grilling. The grill
element and the oven fan operate simultaneously, circulating
hot air around the food. The need to check and turn the food
is reduced. Fan grilling helps to minimize cooking smells in
the kitchen.
How to cook?
Set the function knob on the
thermostat knob to select the temperature between 50°C and
200°C.
Cooking time depends on the thickness of the meat and
not on its weight.
DEFROSTING
The flow of air produced by the fan ensures quicker
defrosting.
The air circulating inside the oven is at room temperature.
Set the function knob on the
must be left on 0.
The advantage of defrosting at room temperature is that
it does not alter the taste and appearance of the food.
/ symbol and use the
symbol. The thermostat knob
43
11. OVEN TEMPERATURE CONVERSION CHART
Instructions for the user
44
Instructions for the user
12. COOKING CHART
ROASTING GUIDE
Function
selector
Beef Fan 2 150 – 160 20-30 per 500 g and 20-30 over
Conventional 2 200 – 210 Ditto
Lamb Fan 2 160 – 180 Ditto
Conventional 2 190 – 200 Ditto
Pork & Veal Fan 2 160 – 180 Ditto
Conventional 2 180 – 190 Ditto
Ham Fan 2 150 – 170 Ditto
Conventional 2 190 – 200 Ditto
Chicken Fan 2 150 – 170 15-20 per 500 g & 20 over
Conventional 2 180 – 190 Ditto
Turkey/goose Fan 2 150 – 170 15 per 500g up to 3.5Kg then 10
Conventional 2 180 - 190 ditto
Stuffed or rolled meats add 10 mins per 500g to the above cooking times
Shelf
level
BAKING CHART
Temperature
selector
Cooking time in minutes
min per 500g
Function
selector
Rich fruit cakes Fan 2 140 40 – 50 per 450 g mixture
Conventional 2 140 Ditto
Victoria sponge Fan 2 – 3 – 4 170 20 - 30
Conventional 2 – 3 180 20 – 30
Scones Fan 2 – 3 210 Approx 15
Conventional 2 – 3 220 Ditto
Bread Fan 2 200 20 – 30
Conventional 2 220 Ditto
Fruit pie Fan 3 190 35 – 45
Conventional 3 200 35 – 40
Meringues Fan 3 100 2 – 2.5 hours
Egg Custard Fan 3 150 45 – 1 hour
Baked sponge Fan 3 180 45 – 45
Milk pudding Fan 3 150 2 – 2.5 hours
Shelf level Temperature
selector
PUDDING
Cooking time in minutes
FOR ALL FOODS PRE-HEAT OVEN FOR 10 MINS
45
Do not use metallic sponges or sharp scrapers: they will damage the surface.
13. CLEANING AND MAINTENANCE
CLEANING
Before performing any operations requiring access to powered parts, switch off the power
supply to the machine.
13.1 Cleaning stainless steel
To keep stainless steel in good condition it should be cleaned regularly after use. Let it cool
first.
13.1.0 Ordinary Daily Cleaning
To clean and preserve the stainless steel surfaces, always use only specific products that do not
contain abrasives or bleach.
How to use: pour the product on a damp cloth and wipe the surface, rinse thoroughly and dry with a
soft cloth or chamois leather.
13.1.1 Food stains or residues
Use normal non-abrasive products for steel, and a wooden or plastic tool if necessary.
Rinse thoroughly and dry with a soft cloth or chamois leather.
Do not allow residues of sugary foods (such as jam) to set inside the oven. If left to set for
too long, they might damage the enamel lining of the oven.
13.2 Cleaning of the oven (without self-cleaning panels)
Instructions for the user
For best oven upkeep clean regularly after having allowed to cool. Take out all removable
parts.
The oven is equipped with continuous self-cleaning enamelled liners.
Periodically, to prevent food residues and unpleasant smells from accumulating inside the oven, the
• Do not use a steam jet for cleaning the inside of the oven.
• Clean the oven grill and side guides with hot water and non-abrasive detergent. Rinse and dry.
• The oven should be operated at the maximum temperature for about 15/20 minutes after using
specific products, to eliminate the residues deposited inside the oven.
• For easier cleaning, the door can be removed (see P. 12.6 / 12.7)
13.3 Cleaning of the oven (with self-cleaning panels)
13.3.2 Self-cleaning liners
These liners make the oven easier to clean and ensure its efficiency over time.
13.3.3 Using the self-cleaning liners
appliance should be operated empty at temperatures of not less than 200°C for a time varying from 30
to 60 minutes, in order to allow the self-cleaning liners to oxidise the residues present. When the oven
has cooled, these will then be removed with a damp sponge
46
Instructions for the user
The liners should not be cleaned with abrasive creams or ordinary detergents. Use a damp sponge
13.3.4 Looking after the self-cleaning liners
only, so as not to damage the special characteristics of the enamel which coats the liners.
13.3.5 Assembling the self-cleaning liners
1. Remove all accessories from the oven;
2. Remove the side grilles (fig.1);
3. Extract the side liners “F” and “G”(fig. 2);
4. Remove the back panel “A” after undoing the threaded ring-nut “C” (fig. 2).
5. Reassemble the panels, restoring them to their original position.
1)
2)
To remove the self-cleaning liner at the back of the small oven, extract it from the two screws on the
bottom of the oven. To replace it, align the two holes on the liner with the two screws on the bottom
and pull down until engaged.
13.4 Door glass
The door glass should always be kept clean. Use absorbent kitchen paper to clean. In case of tough
spots, clean with a damp sponge using regular detergent. This oven door is air cooled. Care should
be taken not to use excess moisture for cleaning, and avoid spillage through the vents.
MAINTENANCE
The oven may require maintenance or replacement of parts subject to wear such as seals, bulbs, and
so on. The following instructions describe how to carry out these minor maintenance operations.
Before any intervention, disconnect the power supply of the device.
13.5 Replacement of light bulb
Remove the bulb protector A by turning anticlockwise and change bulb B with a similar one. Re-fit the
bulb protector A.
Only use oven bulbs (T 300°C).
47
Open the door completely and fit pins (supplied) into the holes from the inside. Close the door to an
13.6 Removing door (large oven)
Hold the door on both sides with both hands near hinges A and raise levers B. Lift up the door forming
an angle of about 45° and remove. To refit, slide the hinges A in the grooves, drop the door and
release levers B.
13.7 Removing door (small oven)
angle of about 45°, lift it and remove it from its seat. To replace, fit the hinge into the groove provided,
then lower the door until it comes to rest and extract the pins. If the pins are lost, two screwdrivers can
also be used.
Instructions for the user
To permit thorough cleaning of the oven, the seal may be removed. Before
13.8 Oven door seal
removing the seal, take off the door as described above. Once the door has been
taken off, lift the tabs at the corners as shown in the figure.
After cleaning, refit the seal with the longer side horizontal and insert the tabs into
the appropriate holes starting from the top ones.
48
Instructions for the user
14. SOMETHING WRONG?
PROBLEM POSSIBLE CAUSES WHAT TO DO?
The oven doesn’t work
The results of cooking are
unsatisfactory
The oven smokes
Steam and condensation settle
on the food and the oven cavity
- The oven is not wired in or
switched on at the wall.
- There is a power failure
- An automatic cooking
program has been set
- Insufficient pre-heating
- Temperature is too high or
too low
- Wrong shelf position
- Wrong type of dish
- Temperature is incorrectly
set
- Cooking time is incorrect
- Cooking function selector is
wrongly positioned
- The shelf or oven dish are
not in the centre of the oven
- The oven is dirty
- Food has spilled over
- Food (meat) is spitting
excessively
- The dish has been left inside
the oven too long
- Switch on at the wall
- Check power suplly
- Set the programmer back to
- Counsult cooking guides
- Centre the shelf or oven dish
- Clean the oven once cooking
- Use a larger dish
- Reduce temperature setting
- Leave dishes inside the oven
the off position
in the oven
is finished. Let it cool first.
no longer than 15 – 20
minutes after the cooking is
completed
The timer keeps flashing
The timer does not work
- There has been a power
failure
- Incorrect setting - Check the instructions for
- Reset the clock
timer
49
Oven type See rating plate
Electrical connections 230 - 240 / 400-415 V 3N ~ 50 Hz
Required protection fuse for the oven 30 Amps
Ovens Electric
Maximum electrical power 6.1 kW
Oven grilling Electric
Large grilling power 3.0 kW (230 V)
Small grilling power 1.8 kW (230 V)
Ovens lightings 25 W (230 V)
Large oven Small oven
Height (cm) 34 23
Width (cm) 46 46
Depth (cm) 40 40
Internal volume (cm
15. INSTALLATION
15.1 Technical information
OVEN RATING
OVEN CAVITY DIMENSIONS
15.2 The rating plate
CHECK THAT MAINS VOLTAGE AND POWER CABLE RATINGS ARE AS PER THE INDICATIONS
PROVIDED ON THE LABEL ATTACHED TO THE OVEN DOOR FRAME.
THIS LABEL MUST NEVER BE REMOVED.
Instructions for the installer
2
) 62560 42320
Model Serial N°
15.3 Electrical connection
IT IS OBLIGATORY FOR THE ELECTRICAL SYSTEM TO BE GROUNDED ACCORDING TO THE
METHODS REQUIRED BY SAFETY RULES.
WHEN LINKING UP TO MAINS BY PLUG AND SOCKET, MAKE SURE THAT BOTH ARE
COMPATIBLE AND CONNECT BY MEANS OF A POWER CABLE COMPLYING WITH
APPLICABLE REGULATIONS.
THE SOCKET MUST BE ACCESSIBLE AFTER THE APPLIANCE HAS BEEN BUILT IN.
NEVER UNPLUG BY PULLING ON THE CABLE.
IMMEDIATELY AFTER INSTALLATION CARRY OUT A BRIEF INSPECTION TEST OF THE OVEN,
FOLLOWING THE INSTRUCTIONS. SHOULD THE APPLIANCE NOT FUNCTION, DISCONNECT
IT FROM THE SUPPLY AND CALL THE NEAREST TECHNICAL ASSISTANCE CENTRE.
NEVER ATTEMPT TO REPAIR THE APPLIANCE.
IF A PLUG AND SOCKET CONNECTION IS BEING USED MAKE SURE THAT THE PLUG AND
SOCKET ARE COMPATIBLE. AVOID USE OF ADAPTERS AND SHUNTS AS THESE COULD
CAUSE OVERHEATING AND RISK OF BURNS.
IF A FIXED CONNECTION IS BEING USED FIT POWER LINE WITH AN OMNIPOLAR CIRCUIT
BREAKER WITH A CONTACT OPENING GAP EQUAL TO OR GREATER THAN 3 MM IN AN
EASILY ACCESSIBLE POSITION IN PROXIMITY TO THE OVEN.
50
Instructions for the installer
For operation on 400-415 V 2N∼: use an H05RR-F / H05RN-F type fourcore cable (4 x 1.5 mm2).
For operation on 230-240 V∼: use an H05RR-F / H05RN-F type threecore cable (3 x 4 mm2).
The cable end to be connected to the appliance must be provided with an
earth wire (yellow-green) at least 20 mm longer.
The manufacturer declines all responsibility for damage to persons or things caused by nonobservance of the above guidelines or by interference with any part of the appliance.
The oven is designed for installing into any piece of furniture as long as heat-resistant. Follow the
15.4 Installing the oven
dimensions given in Figure 1-2 allowing for a clearance of 80 to 90 mm at the top of the column.
Tighten the four screws A inside the frame to secure (Fig. 1).
(1) (2)
The vent B shown in the diagram ensures the air flow required for the oven cooling fans.
Never use the oven door to lever the oven into place when fitting.
Avoid exerting too much pressure on the oven door when open.
51
Loading...