Smeg CWC601D User Manual

PROFESSIONAL DISHWASHER

 2

1 Precautions for safety and use

2 Technical data

3 Installation and positioning

4 INSTALLATION INSTRUCTIONS FOR THE

AFTER-SALES SERVICE

5 Start-up

6 Settings

7 Malfunctions shown on the display (for the technician)

8 INSTRUCTIONS FOR THE USER

9 Choosing the program

10 Supplementary Functions

11 Maintenance and cleaning

12 Troubleshooting

13 Malfunctions shown on the display (for the user)

You are advised to read all the instructions in this manual carefully to become familiar with the right conditions

for the proper use of your dishwasher.

TECHNICAL INSTRUCTIONS:

These are intended for the qualified staff who are to install, commission and test the appliance and carry out any servicing and repairs.

INSTRUCTIONS FOR THE USER:

These provide recommendations for use, a description of the controls and the correct

procedures for cleaning and maintaining the dishwasher.

1 Precautions for safety and use

THIS MANUAL IS AN INTEGRAL PART OF THE DISHWASHER AND MUST ALWAYS BE KEPT WITH THE APPLIANCE.

THE DISHWASHER IS INTENDED ONLY FOR PROFESSIONAL USE BY TRAINED STAFF. IT IS DESIGNED TO WASH TABLEWARE (PLATES, CUPS, BOWLS, OVEN DISHES AND CUTLERY) AND SIMILAR ITEMS IN THE RESTAURANT AND INSTITUTIONAL CATERING SECTOR, AND COMPLIES WITH

THE INTERNATIONAL STANDARDS ON ELECTRICAL AND MECHANICAL SAFETY (CEI-EN-IEC 60335-2- 58/61770) AND ELECTROMAGNETIC COMPATIBILITY (CEI-IEC-EN 55014-1/-2, 61000-3;4, 50366).

THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR INJURY OR DAMAGE CAUSED BY FAILURE TO COMPLY WITH THE ABOVE REGULATIONS OR DERIVING FROM INCORRECT USE, TAMPERING WITH EVEN JUST ONE PART OF THE APPLIANCE AND THE USE OF NON-ORIGINAL

SPARE PARTS.

THIS APPLIANCE IS TAGGED UNDER EUROPEAN DIRECTIVE 2002/96/EC ON WASTE ELECTRICAL AND

ELECTRONIC EQUIPMENT (WEE). BY MAKING SURE THAT THIS PRODUCT IS DISPOSED OF CORRECTLY THE USER HELPS TO PREVENT POTENTIAL DETRIMENTAL EFFECTS ON HEALTH AND THE ENVIRONMENT.

THE PRODUCT MUST NOT BE TREATED AS ORDINARY DOMESTIC WASTE BUT MUST BE CONSIGNED TO THE SPECIAL COLLECTION POINT FOR THE RECYCLING OF ELECTRICAL AND ELECTRONIC EQUIPMENT. WHEN DECOMMISSIONING THE APPLIANCE COMPLY WITH THE LOCAL WASTE DISPOSAL REGULATIONS. FOR FURTHER INFORMATION ON THE TREATMENT, RECOVERY AND RECYCLING OF THIS PRODUCT, CONTACT THE COMPETENT LOCAL OFFICE, THE DOMESTIC WASTE COLLECTION SERVICE, OR THE SHOP WHERE THE PRODUCT WAS PURCHASED.

POSITIONING, CONNECTIONS, COMMISSIONING, TROUBLESHOOTING AND

REPLACEMENT OF THE POWER SUPPLY CABLE MUST BE CARRIED OUT BY SKILLED STAFF.

THE APPLIANCE MUST BE IN COMPLIANCE WITH ELECTRICAL SYSTEM SAFETY

REGULATIONS.

SYMBOL ON THE PRODUCT OR IN THE TECHNICAL DOCUMENTATION INDICATES THAT THIS

NEVER PLACE SOLVENTS SUCH AS ALCOHOL OR TURPENTINE, WHICH MIGHT CAUSE AN EXPLOSION, INSIDE THE APPLIANCE. NEVER LOAD DISHES DIRTY WITH ASH, WAX OR PAINTS.

NEVER USE THE DISHWASHER OR ANY PART OF IT AS A LADDER, SUPPORT OR STAND FOR PEOPLE, ANIMALS OR ANY OBJECT.

DO NOT DRINK ANY WATER LEFT IN THE DISHES OR DISHWASHER AT THE END OF THE WASHING PROGRAM.

THE APPLIANCE IS NOT SUITABLE FOR USE BY JUVENILES OR PERSONS WITH REDUCED PHYSICAL, SENSORIAL OR MENTAL CAPACITIES, OR THOSE WITHOUT THE NECESSARY KNOWLEDGE AND EXPERIENCE. SUCH PERSONS MAY ONLY USE THE APPLIANCE UNDER THE SUPERVISION OF A PERSON RESPONSIBLE FOR THEIR SAFETY.

2 Technical data

TECHNICAL DATA

Supply voltage V 400V 3N ~ Frequency Hz 50 Max. power absorption at 400V 3N ~ kW 10,0 Boiler heating element power at 400V 3N ~ kW 9,0 Tank heating element power kW 1,8 Water intake pressure kPa (bar) 100-600 (1 ÷ 6) Water intake temperature °C 15°C – 60°C Water hardness °f < 15°f Rinse cycle water consumption I 3,2 Boiler capacity I 10 Tank capacity I 22 Standard cycle duration with intake water at 50°C s 60/90/150/variable Degree of protection IPX 5 Net weight kg 120 Power supply cable type ◄HAR► H07RN-F

Fuse A 4

10,0 kW

400V 3N ~

C S

5 x 4 32A

C = Power Supply Cable. S = Master Switch

3 Installation and positioning

INSTALLATION and POSITIONING

Bring the dishwasher to the installation site, remove the packaging and check the appliance and components for damage; any damage found must be reported to the transporter in writing. The packaging components (plastic bags, expanded polystyrene, nails, etc.) must not be left within reach of children and pets since they are potentially dangerous. All packaging materials used are environment-friendly. They can be kept without constituting any hazard, or may be disposed of at a specialist waste disposal centre. The plastic components suitable for recycling are marked as follows:

PE polyethylene: external packaging film, bag containing the instructions, protective bags.

PP polypropylene: straps. PS expanded polystyrene: corner guards, top of packaging.

Wooden and cardboard components can be disposed of in accordance with the relevant regulations. When the product is decommissioned it must not be dumped in the environment; it must be disposed of in accordance with the relevant regulations. All metal parts are in stainless steel and can be removed. The plastic parts are marked with the symbol identifying the material used.

POSITIONING:

Caution: the indoor system and premises in which equipment for institutions is installed must

comply with the relevant regulations.

The manufacturer declines all liability for direct or indirect injury or damage deriving from failure to comply with these regulations. Before installation, check that there are no objects or materials in the vicinity which may be damaged by steam or splashes of washing solution, or that any such items are suitably protected. Place the dishwasher in the chosen point and remove the protective film. Level the dishwasher (with the aid of a spirit level) on its adjustable feet to ensure that it is stable; all other mounting solutions must be approved by the manufacturer. The dishwasher must be secured to the adjoining work-tops by means of suitable fixtures.



2040

max

min1940 - max 2040min1940

797-892

420

LUCEUTILE

235

max

140

min 140 - max 235min

FRONTALE

RETRO

1620

max

min1520 - max 1620min1520

760

716

760

734

SOLENOID VALVE

EARTH TERMINAL

ELECTRICITY SUPPLY CABLE

PERISTALTIC HOSES

ABLAUFSCHLAUCH



824

4 INSTALLATION INSTRUCTIONS FOR THE AFTER-SALES SERVICE

Water supply and drain connection:

The water pipelines and electricity supply cable lead out of the bottom right-hand corner of the appliance. Connect the water intake hose to a

connector with ¾” gas threaded fitting, fitting the filter A provided.

The connection to the water mains must only be made with new hoses; the use of old or worn hoses is not permitted.

An `approved` single check valve or some other no less effective device providing backflow prevention protection to at least fluid category two shall be fitted at the point of connection between the water supply and the fitting or appliance.

The dynamic intake pressure must be between 1 and 6 bar; if it is higher, installation of a pressure reducer is recommended.

It is essential to fit a main stop tap on the water intake pipeline; the tap must be accessible after installation of the appliance, so do not install it behind the dishwasher.

The stated cycle duration refers to appliances supplied with hot water at 50°C.

If the appliance is supplied with cold water, the cycle duration might increase depending on the intake water temperature, since the dishwasher is fitted with the HTR system, which requires set temperature and pressure for rinsing.

Drainage:

The dishwasher is fitted with a drain pump and can operate with drain

connections on the floor or wall.

4.1 Water connection

If the drain connection is to an outlet with valve, the maximum height of the drain is reduced to 600 mm.

In all cases, after installation check that the drain is fully functional by pumping out the tank completely (P0 cycle).

Caution:

constricted or crushed after installation.

make sure that the intake and drain hoses are not bent,

+ 15 hidden pages