Page 1
Contents
1 Instructions 48
1.1 General safety instructions 48
1.2 Identification plate 49
1.3 Manufacturer liability 49
1.4 Appliance purpose 49
1.5 This user manual 49
1.6 Disposal 50
1.7 How to read the user manual 50
2 Description 51
2.1 General Description 51
2.2 Cooking hob 52
2.3 Control panel 52
2.4 Other parts 54
2.5 Available accessories 54
3 Use 58
3.1 Instructions 58
3.2 First use 59
3.3 Using the accessories 59
3.4 Using the hob 61
3.5 Using the storage compartment 62
3.6 Using the oven 62
3.7 Cooking advice 66
3.8 Programmer clock 67
4 Cleaning and maintenance 73
4.1 Instructions 73
4.2 Cleaning the appliance 73
4.3 Removing the doors 74
4.4 Cleaning the door glazing 75
4.5 Cleaning the inside of the ovens 75
4.6 Pyrolytic: automatic cleaning of the main oven (on some models only) 77
4.7 Extraordinary maintenance 78
5 Installation 80
5.1 Gas connection (not valid for the UK) 80
5.2 Adaptation to different types of gas 83
5.3 Electrical connection 87
5.4 Positioning 88
EN
We advise you to read this manual carefully, which contains all the instructions for
maintaining the appliance’s aesthetic and functional qualities.
For further information on the product: www.smeg.com
47
Page 2
Instructions
1 Instructions
1.1 General safety instructions
Risk of personal injury
• During use the appliance and its
accessible parts become very hot.
• Never touch the heating elements
during use.
• Keep children under eight years
of age at a safe distance if they
are not constantly supervised.
• Children must never play with the
appliance.
• This appliance may be used by
children aged at least 8 and by
people of reduced physical and
mental capacity, or lacking in
experience in the use of electrical
appliances, provided that they
are supervised or instructed by
adults who are responsible for
their safety.
• Never try to put out a fire or
flames with water: Turn off the
appliance and smother the flames
with a fire blanket or other
appropriate cover.
• The appliance must never be
cleaned by unsupervised children.
• Do not insert pointed metal
objects (cutlery or utensils) into the
slots in the appliance.
• Do not modify this appliance.
• Switch off the appliance
immediately after use.
• Never rest metallic objects such
as knives, forks, spoons and lids
on the appliance during use.
• Have qualified personnel carry
out installation and assistance
interventions according to the
standards in force.
• Do not try to repair the appliance
yourself or without the intervention
of a qualified technician.
• If the power supply cable is
damaged, contact technical
support immediately and they will
replace it.
• Do not open the storage
compartment when the oven is on
and still hot.
• The items inside the storage
compartment could be very hot
after using the oven.
Risk of damaging the appliance
• Do not use abrasive or corrosive
detergents on glass parts (e.g.
powder products, stain removers
and metallic sponges).
• Use wooden or plastic utensils.
• Do not seat on the appliance.
• Never leave objects on the
cooking surface.
48
Page 3
Instructions
• Racks and trays have to be
inserted into the side guides until
they come to a complete stop.
The mechanical safety locks that
prevent the rack from being taken
out accidentally have to face
downwards and towards the
oven back.
• Do not use steam jets to clean the
appliance.
• Do not obstruct ventilation
openings and heat dispersal slots.
• Never leave the appliance
unattended during cooking
operations where fats or oils
could be released.
• Do not use the appliance to heat
rooms for any reason.
• Remove any food residues or
large spills from previous cooking
operations from the inside of the
oven.
For this appliance
1.3 Manufacturer liability
The manufacturer declines all liability for
damage to persons or property caused by:
• Use of the appliance other than as
envisaged;
• Non-observance of the user manual
provisions;
• Tampering with any part of the
appliance;
• Use of non-original spare parts.
1.4 Appliance purpose
• This appliance is intended for cooking
food in the home environment. Every
other use is considered improper.
• This appliance may be used by children
aged at least 8 and by people of
reduced physical and mental capacity,
or lacking in experience in the use of
electrical appliances, provided that they
are supervised or instructed by adults
who are responsible for their safety.
• The appliance is not designed to
operate with external timers or with
remote-control systems.
EN
• Before replacing the bulb, switch off the
power supply to the appliance.
• Do not rest any weight or sit on the open
door of the appliance.
• Take care that no objects are stuck in the
doors.
1.2 Identification plate
• The identification plate bears the
technical data, serial number and brand
name of the appliance. Do not remove
the identification plate for any reason.
1.5 This user manual
This user manual is an integral part of the
appliance and must therefore be kept in its
entirety and within the user’s reach for the
whole working life of the appliance.
• Read this user manual carefully before
using the appliance.
49
Page 4
Instructions
1.6 Disposal
This appliance must be disposed of
separately from other waste
(Directives 2002/95/EC, 2002/
96/EC, 2003/108/EC).
The appliance does not contain substances
in quantities sufficient to be considered
hazardous to health and the environment, in
accordance with current European
directives.
To dispose of the appliance:
• Cut the power supply cable and remove
it along with the plug.
Power voltage
Danger of electrocution
• Disconnect the main power supply.
• Unplug the appliance.
• Deliver the appliance to the appropriate
recycling centre for electrical and
electronic equipment waste, or return it to
the retailer when purchasing an
equivalent product, on a one for one
basis.
Our appliances are packed in nonpolluting and recyclable materials.
• Deliver the packing materials to the
appropriate recycling centre.
Plastic packaging
Danger of suffocation
1.7 How to read the user manual
This user manual uses the following reading
conventions:
Instructions
General information on this user
manual, on safety and final
disposal.
Description
Description of the appliance and its
accessories.
Use
Information on the use of the
appliance and its accessories,
cooking advice.
Cleaning and maintenance
Information for proper cleaning and
maintenance of the appliance.
Installation
Information for the qualified
technician: Installation, operation
and inspection.
Safety instructions
Information
• Do not leave the packaging or any part
of it unattended.
• Do not let children play with the
packaging plastic bags.
50
Advice
1. Use instruction sequence.
• Standalone use instruction.
Page 5
2 Description
2.1 General Description
Description
EN
1 Cooking hob
2 Control panel
3 Oven light
4 Seal
5 Main oven door
6 Auxiliary oven door
7 Fan
8 Storage compartment
Rack/tray support frame shelf
51
Page 6
2.2 Cooking hob
Description
Aux = Auxiliary
SR = Semi-rapid
2.3 Control panel
R = Rapid
UR2 = Ultra-rapid
Multifunction models
Pyrolytic models
52
Page 7
Description
1 Programmer clock
Useful for displaying the current time, setting
programmed cooking operations and
programming the minute minder timer.
2 Main oven temperature knob
This knob allows you to select the cooking
temperature.
Turn the knob clockwise to the required
value, between the minimum and maximum
setting.
3 Main oven indicator light
The indicator light comes on to indicate that
the oven is heating up. It turns off as soon as
it reaches the set temperature. It flashes
regularly to indicate that the temperature set
inside the oven is kept constant.
4 Main oven function knob
The oven's various functions are suitable for
different cooking methods. After selecting
the required function, set the cooking
temperature using the temperature knob.
5 Door lock indicator light
(On pyrolytic models only)
It comes on when the automatic (pyrolytic)
cleaning cycle is activated.
6 Hob burner knobs
Useful for lighting and adjusting the hob
burners.
Press and turn the knobs anti-clockwise to
the value to light the relative burners.
Turn the knobs to the zone between the
maximum and minimum setting to
adjust the flame.
Return the knobs to the position to turn
off the burners.
7 Auxiliary oven temperature knob
This knob allows you to select the cooking
temperature.
Turn the knob clockwise to the required
value, between the minimum and maximum
setting.
8 Auxiliary oven indicator light
The indicator light comes on to indicate that
the oven is heating up. It turns off as soon as
it reaches the set temperature. It flashes
regularly to indicate that the temperature set
inside the oven is kept constant.
9 Auxiliary oven function knob
The oven's various functions are suitable for
different cooking methods. After selecting
the required function, set the cooking
temperature using the temperature knob.
EN
53
Page 8
Description
2.4 Other parts
Shelves
The appliance features shelves for
positioning trays and racks at different
heights. The insertion heights are indicated
from the bottom upwards (see 2.1 General
Description).
Cooling fan
The fan cools the ovens and comes into
operation during cooking.
The fan causes a steady outflow of air that
exits from the rear of the appliance and
which may continue for a brief period of
time even after the appliance has been
turned off.
Interior lighting
2.5 Available accessories
Supplied original and optional
accessories can be requested to
Authorised Assistance Centres.
Use only original accessories
supplied by the manufacturer.
WOK ring
Useful when using a wok.
Raised pan support
The appliance interior lighting comes on:
• When the door is opened
• When any function is selected, apart
from the function.
54
To prevent damage to the worktop, a
raised pan support is available to place
under pans having a diameter greater than
those indicated in the “Cookware
diameters” table in section 3.3 “Using the
hob”.
Page 9
Description
The pan support must be placed on the hob
grid as shown in the figure above.
In any case, pans with a diameter greater
than 26 cm must be used solely on the
Ultra-rapid burner (UR2).
This pan support can also be used with
woks.
Oven tray
Deep tray (on some models only)
EN
Useful for collecting fat from foods placed
on the rack above and for cooking pies,
pizzas and baked desserts.
Tray rack
Useful for collecting fat from foods placed
on the rack above.
To be placed over the top of the oven tray;
for cooking foods which may drip.
55
Page 10
Description
Rack
Useful for supporting containers with food
during cooking.
Self-cleaning panels (on some models
only)
Rotisserie support
To be used to support the rotisserie rod.
Useful for absorbing small grease residues.
56
Page 11
Description
Rotisserie rod
Useful for cooking chicken and all foods
which require uniform cooking over their
entire surface.
The oven accessories intended to
come into contact with food are
made of materials that comply with
the provisions of current legislation.
EN
57
Page 12
Use
3 Use
3.1 Instructions
High temperature inside the oven
during use
Danger of burns
• Keep the oven door closed during
cooking.
• Protect your hands wearing heat
resistant gloves when moving food
inside the oven.
• Do not touch the heating elements inside
the oven.
• Do not pour water directly onto very hot
trays.
• Do not allow children younger than 8
years old to come near the appliance
when in operation.
• If you need to move food or at the end
of cooking, open the door 5 cm for a
few seconds, let the steam come out,
then open it fully.
High temperature inside the
storage compartment
Danger of burns
• Do not open the storage compartment
when the oven is on and still hot.
• The items inside the storage
compartment could be very hot after
using the oven.
Improper use
Danger of burns
• Make sure that the flame-spreader
crowns are correctly positioned in their
housings with their respective burner
caps.
• Oils and fats could catch fire if
overheated. Be very careful.
High temperature inside the oven
during use
Danger of fire or explosion
• Do not spray any spray products near
the oven.
• Do not use or leave flammable materials
near the oven or the storage
compartment.
• Do not use plastic kitchenware or
containers when cooking food.
• Do not put sealed tins or containers in
the oven.
• Do not leave the oven unattended
during cooking operations where fats or
oils could be released.
• Remove all trays and racks which are
not required during cooking.
58
Page 13
Use
Improper use
Risk of damage to surfaces
• Do not cover the bottom of the oven
cavity with aluminium or tin foil sheets.
• If you wish to use greaseproof paper,
place it so that it will not interfere with the
hot air circulation inside the oven.
• Do not place pans or trays directly on
the bottom of the oven cavity.
• Do not use the open door to rest pans or
trays on the internal glass pane.
• Do not pour water directly onto very hot
trays.
• Make sure that the flame-spreader
crowns are correctly positioned in their
housings with their respective burner
caps.
• Cooking vessels or griddle plates
should be placed inside the perimeter of
the hob.
• All pans must have smooth, flat bottoms.
• If any liquid does boil over or spill,
remove the excess from the hob.
3.2 First use
1. Remove any protective film from the
outside or inside of the appliance,
including accessories.
2. Remove any labels (apart from the
technical data plate) from the
accessories and from the cooking
compartments.
3. Remove all the accessories from the
appliance and clean them (see 4
Cleaning and maintenance). Heat the
empty ovens at the maximum
temperature to burn off any residues left
by the manufacturing process.
3.3 Using the accessories
Tray rack
The tray rack has to be inserted into the tray.
In this way fat can be collected separately
from the food which is being cooked.
EN
59
Page 14
Use
Racks and trays
Racks and trays have to be inserted into the
side guides until they come to a complete
stop.
• The mechanical safety locks that prevent
the rack from being taken out
accidentally have to face downwards
and towards the oven back.
Ring reducers
The ring reducers have to be placed on the
hob grids. Make sure they are properly
placed.
60
Gently insert racks and trays into
the oven until they come to a stop.
Clean the trays before using them
for the first time to remove any
residues left by the manufacturing
process.
Page 15
Use
Auxiliary oven rotisserie
1. Position the rotisserie support on the third
shelf of the auxiliary oven.
2. Screw on the handle provided so that
you can handle the rod with the food on
it readily.
3. Once you have prepared the rotisserie
rod, place it on the rotisserie support. The
pin must be correctly positioned on the
shaped part A.
4. Insert the rod into the hole B so that it
connects with the rotisserie motor.
3.4 Using the hob
All the appliance’s control and monitoring
devices are located together on the front
panel. The burner controlled by each knob
is shown next to the knob. The appliance is
equipped with an electronic ignition device.
Simply press the knob and turn it anticlockwise to the maximum flame symbol,
until the burner lights. If the burner does not
light in the first 15 seconds, turn the knob to
and wait 60 seconds before trying
again. After lighting, keep the knob pressed
in for a few seconds to allow the
thermocouple to heat up. The burner may
go out when the knob is released: In this
case, the thermocouple has not heated up
sufficiently. Wait a few moments and repeat
the operation. Keep the knob pressed in
longer.
In case of an accidental switching
off, a safety device will be tripped,
cutting off the gas supply, even if
the gas tap is open. Return the
knob to and wait at least 60
seconds before lighting it again.
EN
Remove the handle before closing
the door
We recommend that you place the
tray on the first shelf to collect fats
more easily.
Pour a little water into the drip tray
to prevent smoke from forming.
61
Page 16
Use
Correct positioning of the flamespreader crowns and burner caps
Before lighting the hob burners, make sure
that the flame-spreader crowns are
correctly positioned in their housings with
their respective burner caps. Make sure that
the holes in the flame-spreader crowns are
aligned with the igniters and thermocouples
(A).
Practical tips for using the hob
For better burner efficiency and to minimise
gas consumption, use pans with lids and of
suitable size for the burner, so that flames
do not reach up the sides of the pan. Once
the contents come to the boil, turn down the
flame far enough to ensure that the liquid
does not boil over.
3.5 Using the storage compartment
The storage compartment is at the bottom of
the cooker. To open it, pull the handle
towards you. It can be used to store
cookware or metallic objects necessary
when using the appliance.
3.6 Using the oven
Switching on the oven
To switch on the oven:
1. Select the cooking function using the
function knob.
2. Select the temperature using the
temperature knob.
Regular flashing of the thermostat
indicator light during cooking is
normal and indicates that the
temperature is being maintained
constant inside the oven.
62
Cookware diameters:
• AUX.: 12 - 14 cm.
• SR: 16 - 24 cm.
• R: 18 - 26 cm.
• UR2: 18 - 26 cm.
Cookware diameters with raised
pan support:
• UR2: 26 - 28 cm.
Page 17
Use
Main oven functions
Static
As the heat comes from above and
below at the same time, this system
is particularly suitable for certain
types of food. Traditional cooking,
also known as static cooking, is
suitable for cooking just one dish at
a time. Perfect for all types of roasts,
bread and cakes, and in any case,
particularly suitable for fatty meats
such as goose and duck.
Fan assisted
The operation of the fan, combined
with traditional cooking, ensures
consistent cooking even with
complex recipes. Perfect for biscuits
and cakes, even when
simultaneously cooked on several
levels. (For multiple-level cooking,
we recommend using the 2
th
shelves).
4
Small grill
Using only the heat released from
the central element, this function
allows you to grill small portions of
meat and fish for making kebabs,
toasted sandwiches and any types
of grilled vegetable side dishes.
Fan with grill
The air produced by the fan softens
the strong heatwave generated by
the grill, grilling perfectly even very
thick foods. Perfect for large cuts of
meat (e.g. shin of pork).
nd
and
Fan + lower element
The combination of the fan with just
the lower heating element allows
cooking to be completed more
rapidly. This system is
recommended for sterilising or for
finishing off the cooking of foods
which are already well-cooked on
the surface, but not inside, which
therefore need a little more heat.
Perfect for any type of food.
In pyrolytic models, the special
defrost and proving functions are
brought together under the same
function.
Lower element + fan with circulaire
Fan-assisted cooking is combined
with the heat coming from the
bottom and allows you at the same
time to slightly brown food. Perfect
for any type of food
Fan with circulaire
The combination of the fan and the
circulaire heating element
(incorporated in the rear of the
oven) allows you to cook different
foods on several levels, as long as
they need the same temperatures
and same type of cooking. Hot air
circulation ensures instant and even
distribution of heat. It will be
possible, for instance, to cook fish,
vegetables and biscuits
simultaneously (on different levels)
without odours and flavours
mingling.
EN
63
Page 18
Use
Eco (on some models only)
Using the grill and the lower heating
element in combination is
particularly suitable for cooking on
a single shelf, as it provides low
energy consumption.
Wide grill
The heat coming from the grill
element gives perfect grilling results
above all for thin and medium
thickness meat and, in combination
with the rotisserie (where fitted),
gives the food an even browning at
the end of cooking. Perfect for
sausages, spare ribs and bacon.
This function enables large
quantities of food, particularly meat,
to be grilled evenly.
Turbo (on some models only)
The combination of fan assisted
cooking and traditional cooking
allows different foods to be cooked
on several levels extremely quickly
and efficiently, without odours and
flavours mingling. Perfect for large
volumes that call for intense
cooking.
Pyrolytic (on some models only)
Setting this function, the oven
reaches temperatures up to 500°C,
destroying all the grease which
forms on the internal walls.
64
Rapid defrost (on some models
only)
Rapid defrost is helped by the
activation of a fan to ensure uniform
distribution of room temperature air
inside the oven. Perfect for any type
of food.
Page 19
Use
Auxiliary oven functions
Static
As the heat comes from above and
below at the same time, this system
is particularly suitable for certain
types of food. Traditional cooking,
also known as static cooking, is
suitable for cooking just one dish at
a time. Perfect for all types of roasts,
bread and cakes, and in any case,
particularly suitable for fatty meats
such as goose and duck.
Upper element
The heat coming just from the top is
ideal for foods which require final
browning without the need to use
the grill.
Lower element
The heat coming just from the
bottom allows you to complete the
cooking of foods that require a
higher bottom temperature, without
affecting their browning. Perfect for
cakes, pies, tarts and pizzas.
Wide grill
The heat coming from the grill
element gives perfect grilling results
above all for thin and medium
thickness meat and, in combination
with the rotisserie (where fitted),
gives the food an even browning at
the end of cooking. Perfect for
sausages, spare ribs and bacon.
This function enables large
quantities of food, particularly meat,
to be grilled evenly.
Grill + rotisserie
The rotisserie works in combination
with the grill element, allowing food
to be perfectly browned.
EN
Small grill
Using only the heat released from
the central element, this function
allows you to grill small portions of
meat and fish for making kebabs,
toasted sandwiches and any types
of grilled vegetable side dishes.
65
Page 20
Use
3.7 Cooking advice
General advice
• Use a fan assisted function to achieve
consistent cooking at several levels.
• It is not possible to shorten cooking times
by increasing the temperature (the food
could be overcooked on the outside and
undercooked on the inside).
• Using more ovens at the same time might
affect the final cooking results.
Advice for cooking meat
• Cooking times vary according to the
thickness and quality of the food and to
consumer taste.
• Use a meat thermometer when roasting
meat, or simply press on the roast with a
spoon. If it is hard, it is ready; If not, it
needs another few minutes cooking.
Advice for cooking with the Grill and the
Fan with grill
• Meat can be grilled even when it is put
into the cold oven or into the preheated
oven if you wish to change the effect of
the cooking.
• With the Fan with grill function, we
recommend that you preheat the oven
before grilling.
• We recommend placing the food at the
centre of the rack.
• With the Grill function, we recommend
that you turn the temperature knob to the
maximum value near the symbol to
optimise cooking.
• Foods should be seasoned before
cooking. Foods should also be coated
with oil or melted butter before cooking.
• Use the oven tray on the first bottom shelf
to collect fluids produced by grilling.
• Grilling processes should never last more
than 60 minutes using multifunction
ovens, 30 minutes inside the auxiliary
oven.
Advice for cooking desserts/pastries and
biscuits
• Use dark metal moulds: They help to
absorb the heat better.
• The temperature and the cooking time
depend on the quality and consistency
of the dough.
• To check whether the dessert is cooked
right through: At the end of the cooking
time, put a toothpick into the highest point
of the dessert. If the dough does not stick
to the toothpick, the dessert is cooked.
• If the dessert collapses when it comes
out of the oven, on the next occasion
reduce the set temperature by about
10°C, selecting a longer cooking time if
necessary.
• While cooking desserts or vegetables,
excessive condensation may form on the
glass. In order to avoid this, open the
door very carefully a couple of times
while cooking.
66
Page 21
Use
Advice for defrosting and proving
• Place frozen foods without their
packaging in a lidless container on the
first shelf of the oven.
• Avoid overlapping the food.
• To defrost meat, use the rack placed on
the second level and a tray on the first
level. In this way, the liquid from the
defrosting food drains away from the
food.
• The most delicate parts can be covered
with aluminium foil.
• For successful proving, a container of
water should be placed in the bottom of
the oven.
To save energy
• Stop cooking a few minutes before the
time normally used. Cooking will
continue for the remaining minutes with
the heat which has accumulated inside
the oven.
• Reduce any opening of the door to a
minimum to avoid heat dispersal.
• Keep the inside of the appliance clean
at all times.
3.8 Programmer clock
EN
1 Minute minder timer key
2 End of cooking key
3 Time setting and reset key
4 Value decrease key
5 Value increase key
The programmer clock only
controls the left main oven and
does not control the auxiliary oven.
Setting the time
On the first use, or after a power failure, the
display flashes at regular intervals. Press
to stop the flashing. Press again for two
seconds to start the procedure for setting
the current time. Use the keys or to
increase or decrease the time value by one
minute each time you press the key until
setting the required time. The clock starts
working 5 seconds after the last key was
pressed.
67
Page 22
Use
Timed cooking
Timed cooking is the function
which allows a cooking operation
to be started and then ended after
a specific length of time set by the
user.
1. After selecting a cooking function and
temperature, press the key. The
pointer moves to position 12 and the
symbol will flash on the display.
2. To set the cooking time press the key
or within 5 seconds: each time you
press the key adds 1 minute to the
cooking time, and every 12 minutes a
new internal segment will light up (the
example below shows a cooking time of
1 hour).
3. Once the required time is obtained,
cooking will start about 5 seconds after
you last pressed the key or .
4. The display will show the current time,
represented by the constantly illuminated
segments, and the minutes left to the end
of cooking, represented by the flashing
segments (each flashing segment means
12 minutes of cooking time left).
5. At the end of cooking, the timer will
switch the oven heating elements off, the
buzzer will start to sound and the
numbers on the dial will flash.
6. The set program can be cancelled: Press
the key for 2 seconds to cancel the
set time and switch the oven off manually
if a cooking operation is in progress.
It is not possible to set a cooking
time of more than 12 hours.
68
Page 23
Use
Programmed cooking
Programmed cooking is the
function which allows a cooking
operation to be started at a set
time and then ended after a
specific length of time set by the
user.
1. Set the cooking time as described in the
previous point “Timed cooking”.
2. Within 5 seconds after the last time you
pressed the key or , press the key
again to set the cooking end time.
The symbol will flash on the display
together with the current time, with the
internal segments illuminated to show the
end of cooking time.
3. Press the key or to set the
cooking end time.
4. Five seconds after the last time you
pressed a key, the display will show the
current time and the cooking start and
end times, represented by the illuminated
internal segments. As soon as the current
time reaches the set cooking start time,
the internal segments will flash and the
oven starts cooking.
5. At the end of cooking, the timer switches
the oven heating elements off, the buzzer
starts to sound and the numbers on the
dial flash.
6. The set program can be cancelled: Press
the key for 2 seconds to cancel the
set time and switch the oven off manually
if a cooking operation is in progress.
• In the example below, the current time is
7.06 and cooking is programmed to
start at 8.00 and end at 9.00.
• At 8 o'clock the internal segments
between 8 and 9 will start to flash.
For the oven to start cooking after
the programming procedures just
described, the knobs must be
correctly set on the required
temperature and function.
EN
69
Page 24
Use
Display reduced brightness
To reduce energy consumption in stand-by,
briefly press the key to reduce the
display brightness. To restore the normal
brightness, press the key again.
Timer
This function only activates the
buzzer, without stopping cooking.
1. Press the key and the display will light
up as shown in the figure below.
2. Within 5 seconds press the key or
to set the minute minder timer. Each
time a key is pressed, an outer segment
representing 1 minute of cooking is lit or
switched off (the example below shows
a countdown of 1 hour and 10 minutes).
3. Five seconds after you last pressed the
key the countdown begins, at the end of
which the buzzer activates.
4. During the countdown, the current time
can be displayed by pressing the key
.
5. Press the key again to return to the
minute minder display.
At the end of the countdown turn
the temperature and function
knobs to O to manually stop the
cooking operation.
It is not possible to set a cooking
time of more than 4 hours.
70
Page 25
Use
Auxiliary oven cooking information table
Runner
position from
the bottom
Food
Spit-roast chicken
Rotisserie pork neck
Roast rabbit
Roast chicken
Chops
Hamburgers
Pork sausages
Pork spare ribs
Bacon
Weight
(Kg)
1.2 Grill + rotisserie 220 - 250 70 - 80
2.5 Grill + rotisserie 200 200 - 220
1 Static 2 190 - 200 85 - 90
1 Static 2 190 - 200 80 - 85
0.8 Grill 4 250 13 5
0.6 Grill 4 250 7 3
0.6 Grill 4 250 15 -
0.7 Grill 4 250 30 - 35 -
0.6 Grill 4 250 10 3
Function
The times indicated in the table do not include preheating times and are provided only as a guide.
Temperature
(°C)
Time (minutes)
1st surface 2nd surface
EN
71
Page 26
Main oven cooking information table
Food Weight (Kg) Function
Lasagne
Pasta bake
3 - 4 Static 1 220 - 230 45 - 50
3 - 4 Static 1 220 - 230 45 - 50
Use
position from
the bottom
Runner
Temperature
(°C)
Time (minutes)
Roast veal
Pork
Sausages
Roast beef
Roast rabbit
Turkey breast
Roast pork neck
Roast chicken
Pork chops
Spare ribs
Bacon
Pork fillet
Beef fillet
Salmon trout
Monkfish
Turbot
Pizza
Bread
Focaccia
Bundt cake
Jam tart
Ricotta cake
Jam tarts
Paradise cake
Profiteroles
Sponge cake
Rice pudding
Brioches
2 Turbo/Circulaire 2 180 - 190 90 - 100
2 Turbo/Circulaire 2 180 - 190 70 - 80
1.5 Fan with grill 4 250/280 15
1 Turbo/Circulaire 2 200 40 - 45
1.5 Circulaire 2 180 - 190 70 - 80
3 Turbo/Circulaire 2 180 - 190 110 - 120
2 - 3 Turbo/Circulaire 2 180 - 190 170 - 180
1.2 Turbo/Circulaire 2 180 - 190 65 - 70
1st surface 2nd surface
1.5 Fan with grill 4 250/280 15 5
1.5 Fan with grill 4 250/280 10 10
0.7 Grill 5 250/280 7 8
1.5 Fan with grill 4 250/280 10 5
1 Grill 5 250/280 10 7
1.2 Turbo/Circulaire 2 150 - 160 35 - 40
1.5 Turbo/Circulaire 2 160 60 - 65
1.5 Turbo/Circulaire 2 160 45 - 50
1 Turbo/Circulaire 2 250/280 8 - 9
1 Circulaire 2 190 - 200 25 - 30
1 Turbo/Circulaire 2 180 - 190 20 - 25
1 Circulaire 2 160 55 - 60
1 Circulaire 2 160 35 - 40
1 Circulaire 2 160 - 170 55 - 60
1 Turbo/Circulaire 2 160 20 - 25
1.2 Circulaire 2 160 55 - 60
1.2 Turbo/Circulaire 2 180 80 - 90
1 Circulaire 2 150 - 160 55 - 60
1 Turbo/Circulaire 2 160 55 - 60
0.6 Circulaire 2 160 30 - 35
The times indicated in the table do not include preheating times and are provided only as a guide.
72
Page 27
Cleaning and maintenance
4 Cleaning and maintenance
4.1 Instructions
Improper use
Risk of damage to surfaces
• Do not use steam jets to clean the
appliance.
• Do not use cleaning products containing
chlorine, ammonia or bleach on steel
parts or parts with metallic finishes on the
surface (e.g. anodizing, nickel- or
chromium-plating).
• Do not use abrasive or corrosive
detergents on glass parts (e.g. powder
products, stain removers and metallic
sponges).
• Do not use rough or abrasive materials
or sharp metal scrapers.
• Do not wash the removable
components such as the hob grids,
flame-spreader crowns and burner caps
in a dishwasher.
4.2 Cleaning the appliance
To keep the surfaces in good condition,
they should be cleaned regularly after use.
Let them cool first.
Ordinary daily cleaning
Always use only specific products that do
not contain abrasives or chlorine-based
acids.
Pour the product onto a damp cloth and
wipe the surface, rinse thoroughly and dry
with a soft cloth or a microfibre cloth.
Food stains or residues
Do not use metallic sponges or sharp
scrapers as they will damage the surfaces.
Use ordinary non-abrasive products with
the aid of wooden or plastic utensils if
necessary. Rinse thoroughly and dry with a
soft cloth or a microfibre cloth.
Do not allow residues of sugary foods (such
as jam) to set inside the oven. If left to set for
too long, they might damage the enamel
lining of the oven.
Cooking hob grids
Remove the grids and clean them with
lukewarm water and non-abrasive
detergent. Make sure to remove any
encrustations. Dry them thoroughly and
return them to the hob.
Continuous contact between the
grids and the flame can cause
modifications to the enamel over
time in those parts exposed to
heat. This is a completely natural
phenomenon which has no effect
on the operation of this
component.
Flame-spreader crowns and burner caps
For easier cleaning, the flame-spreader
crowns and the burner caps can be
removed. Wash them in hot water and nonabrasive detergent. Carefully remove any
encrustation, then wait until they are
perfectly dry. Refit the flame-spreader
crowns making sure that they are correctly
positioned in their housings with their
respective burner caps.
EN
73
Page 28
Cleaning and maintenance
Igniters and thermocouples
For correct operation the igniters and
thermocouples must always be perfectly
clean. Check them frequently and clean
them with a damp cloth if necessary.
Remove any dry residues with a wooden
toothpick or a needle.
4.3 Removing the doors
For easier cleaning, the doors can be
removed and placed on a tea towel or
other protective sheet.
To remove the door proceed as follows:
1. Open the door completely and insert two
pins into the holes on the hinges
indicated in the figure.
2. Grasp the door on both sides with both
hands, lift it forming an angle of around
30° and remove it.
3. To reassemble the door, put the hinges in
the relevant slots in the oven, making sure
that grooved sections A are resting
completely in the slots. Lower the door
and once it is in place remove the pins
from the holes in the hinges.
74
Page 29
Cleaning and maintenance
4.4 Cleaning the door glazing
The glass in the door should always be kept
thoroughly clean. Use absorbent kitchen
roll. In case of stubborn dirt, wash with a
damp sponge and an ordinary detergent.
We recommend the use of
cleaning products distributed by
the manufacturer.
4.5 Cleaning the inside of the ovens
To keep the ovens in perfect condition,
clean them regularly after allowing them to
cool.
• Take out all removable parts.
Removing self-cleaning panels and
racks/trays support frames
Removing the guide frames enables the
sides to be cleaned more easily. This
operation should be performed each time
the automatic cleaning cycle is used (on
some models only).
To remove the guide frames: Pull the frame
towards the inside of the oven to unhook it
from its groove A, then slide it out of the
seats B at the back.
When cleaning is complete, repeat the
above procedures to put the guide frames
back in.
EN
• Clean the oven racks with warm water
and non-abrasive detergent. Carefully
rinse and dry damp parts.
The ovens should be operated at
the maximum temperature for
about 15-20 minutes after using
cleaning products, to burn off the
residues left inside the oven.
For easier cleaning, remove the
door.
Pyrolytic model
Model with self-cleaning panels
75
Page 30
Cleaning and maintenance
Regeneration of self-cleaning panels
(catalysis cycle) (where present)
The regeneration cycle of the self-cleaning
panels is a cleaning method through
heating suitable for removing small grease
residues, not sugar-based ones.
1. Clean the base and the upper guard first
with a microfibre cloth soaked in water
and neutral washing up liquid. Rinse
thoroughly.
2. Set a regeneration cycle by selecting a
fan assisted function at the maximum
temperature for one hour.
3. If the panels are particularly dirty after the
regeneration cycle, remove them and
wash them with neutral washing up
liquid. Rinse and dry them.
Put the panels back in the oven and set a
fan assisted function at a temperature of
180°C for one hour, in order to ensure that
they are thoroughly dry.
We recommend carrying out the
self-cleaning panel regeneration
cycle every 15 days.
Cleaning the top section (main oven)
The oven cavity is fitted with a tilting heating
element which facilitates cleaning the top
part (roof) of the oven.
1. Delicately push the middle section of the
upper heating element towards the rear
of the oven to release it from the central
bush.
2. Gently lower the heating element until it
stops.
Improper use
Risk of damage to the appliance
• Do not excessively flex the element
during cleaning.
76
3. When you have finished cleaning, put
the heating element back in position.
Page 31
Cleaning and maintenance
4.6 Pyrolytic: automatic cleaning of
the main oven (on some models
only)
Pyrolytic is an automatic hightemperature cleaning procedure
which causes dirt to dissolve.
Thanks to this process, it is possible
to clean the inside of the oven very
easily.
Improper use
Risk of damage to surfaces
• Remove any food residues or large spills
from previous cooking operations from
the inside of the oven.
• Switch off the burners or electric hot
plates of the hob installed above the
oven.
Preliminary operations
Before starting the pyrolytic cycle:
• Clean the internal glass pane following
the usual cleaning instructions.
• For very stubborn encrustations spray an
oven cleaning product onto the glass
(read the warnings on the product);
leave for 60 minutes, then rinse and dry
the glass using kitchen roll or a microfibre
cloth.
• Completely remove all accessories from
inside the oven.
• Remove the racks/trays support frames.
• Close the door.
Pyrolytic function setting
Before activating the pyrolytic
function, ensure that the auxiliary
oven is off: the pyrolytic function
cannot be activated while the
auxiliary oven is on.
If the auxiliary oven is switched on
during a pyrolytic cycle, this will be
interrupted. The main oven
indicator light will stop flashing and
the door lock will be deactivated,
while still maintaining the safety
conditions provided for.
1. Turn the function knob to the symbol.
The programmer sets automatically the
minimum cleaning cycle time (90
minutes).
2. Press the key or within 5 seconds
to set the cleaning cycle time from a
minimum of 90 minutes to a maximum of
3 hours. The set minutes will be indicated
by the internal segments of the clockface,
while the hours will be indicated by the
relevant numbers flashing (1, 2 or 3)
Recommended pyrolytic cycle
duration:
• Light dirt: 90 minutes.
• Medium dirt: 135 minutes.
• Heavy dirt: 180 minutes.
3. To confirm pyrolytic cycle start, press the
key.
.
EN
77
Page 32
Cleaning and maintenance
4. After selecting the pyrolytic cycle
duration, the thermostat indicator light
starts to flash and the oven starts to heat
up (approx. 5 seconds after the last
intervention by the user).
5. One minute after the pyrolytic cycle has
started the door is locked (the door lock
indicator light comes on) by a device
that prevents the door from being
opened.
It is not possible to select any
function once the door lock device
has been activated.
6. At the end of the pyrolytic cycle, all the
numbers will flash and a buzzer will
sound to indicate the end of the
automatic cleaning cycle.
7. Return the function knob to the O
position.
8. The door remains locked as long as the
temperature inside the oven returns to
safety levels.
9. Wait for the oven to cool down and
collect the residues deposited inside with
a damp microfibre cloth.
During the pyrolytic cycle the fans
produce a more intense level of
noise due to a greater rotation
speed. This is an absolutely normal
operation, intended to provide
more effective heat dispersal. At
the end of the pyrolytic cycle, the
fans will continue to operate for
long enough to avoid overheating
the walls of adjacent units and the
front of the oven.
4.7 Extraordinary maintenance
Live parts
Danger of electrocution
• Disconnect the oven power supply.
Replacing the interior light bulb (main
oven)
1. Completely remove all accessories from
inside the oven.
2. Remove the racks/trays support frames.
3. Remove the bulb cover using a tool (e.g.
a screwdriver).
78
During the first pyrolytic cycle,
unpleasant odours may occur due
to the normal evaporation of oily
manufacturing substances. This is
an absolutely normal phenomenon
which disappears after the first
pyrolytic cycle.
Page 33
Cleaning and maintenance
4. Slide out and remove the lamp.
Do not touch the halogen lamp
directly with your fingers, but wrap
it in insulating material.
5. Replace the lamp with one of the same
type (40W).
6. Refit the cover correctly, so that the
moulded part of the glass is facing the
door.
7. Press the cover completely down so that
it attaches perfectly to the bulb support.
Replacing the interior light bulb
(auxiliary oven)
Removing the oven door seal (not on
pyrolytic models)
To permit thorough cleaning of the oven, the
door seal may be removed. There are
hooks on all four sides to attach it to the
edge of the oven. Pull the edges of the seal
outwards to detach the hooks.
To keep the seals clean, use a non-abrasive
sponge and lukewarm water. Seals should
be soft and elastic.
EN
1. Unscrew bulb protector A (turn anti-
clockwise).
2. Replace bulb B with one of the same
type (25W). Use only oven bulbs (T
300°C).
3. Re-fit bulb protector A.
79
Page 34
Installation
5 Installation
5.1 Gas connection (not valid for the
UK)
For installation in the UK, please
refer to the “Local specifications for
UK gas appliances installation”
booklet.
Gas leak
Danger of explosion
• After carrying out any operation, check
that the tightening torque of gas
connections is between 10 Nm and 15
Nm.
• If required, use a pressure regulator that
complies with current regulations.
• At the end of the installation, check for
any leaks with a soapy solution, never
with a flame.
• Installation using a hose must be carried
out so that the length of the piping does
not exceed 2 metres when fully
extended for steel hoses and 1.5 metres
for rubber hoses.
• The hoses should not come into contact
with moving parts and should not be
crushed in any way.
Connection with a rubber hose
Verify that all following conditions are met:
• the hose is fixed to the hose connection
with safety clamps;
• no part of the hose is in contact with hot
walls (max. 50 °C);
• the hose is not under traction or tension
and has no kinks or twists;
• the hose is not in contact with sharp
objects or sharp corners;
• if the hose is not perfectly airtight and
leaks gas, do not try to repair it; replace
it with a new hose.
• verify that the hose is not past its expiry
date (serigraphed on the hose itself).
Make the connection to the gas mains
using a rubber hose whose specifications
comply with current standards (verify that
the reference standard is stamped on the
hose).
General information
Connection to the gas mains can be made
using a continuous wall steel hose in
compliance with the guidelines established
by the standards in force.
For supplying it with other types of gas, see
chapter “5.2 Adaptation to different types
of gas”. The gas inlet connection is
threaded ½” external gas (ISO 228-1).
80
Page 35
Installation
Carefully screw hose connector 3 to the
appliance’s gas connector 1 (½” ISO 2281 thread), placing seal 2 between them.
Hose connector 4 can also be screwed to
hose connector 3, depending on the
diameter of the gas hose used. After
tightening the hose connector(s), push gas
hose 6 onto the hose connector and secure
it with clamp 5 (which must be compliant
with the applicable standard).
Connection using a rubber hose
complying with current standards is
only permitted if the hose can be
inspected along its entire length.
Connection to LPG
Use a pressure regulator and make the
connection on the gas cylinder following
the guidelines set out in the standards in
force.
The supply pressure must comply with the
values indicated in the table in “Gas types
and Countries”.
Connection with a steel hose
Make the connection to the gas mains
using a continuous wall steel hose whose
specifications comply with the applicable
standard.
Carefully screw the connector 3 to the gas
connector 1 of the appliance, placing the
seal 2 between them.
EN
The inside diameter of the hose
must be 8 mm for LPG and 13 mm
for Natural gas and City gas.
81
Page 36
Installation
Connection with a steel hose with
bayonet fitting
Carry out the connection to the gas mains
using a steel hose with bayonet fitting
compliant with B.S. 669. Apply insulating
material to the thread of the gas hose
connector 4 and then tighten the adapter 3.
Screw the assembly to the movable
connector 1 of the appliance, placing the
supplied seal 2 between them.
Connection with a steel hose with conical
fitting
Make the connection to the gas mains
using a continuous wall steel hose whose
specifications comply with the applicable
standard.
Carefully screw the hose connector 3 to the
appliance’s gas connector 1 (½” thread
ISO 228-1), placing the supplied seal 2
between them. Apply insulating material to
the thread of connector 3, then tighten the
steel hose 4 to the connector 3.
Room ventilation
The appliance should be installed in rooms
that have a permanent air supply in
accordance with the standards in force. The
room where the appliance is installed must
have enough air flow for the regular
combustion of gas and the necessary air
change in the room itself. The air vents,
protected by grilles, must be the right size to
comply with current regulations and
positioned so that no part of them is
obstructed, not even partially.
The room must be kept adequately
ventilated in order to eliminate the heat and
humidity produced by cooking: In
particular, after prolonged use, you are
recommended to open a window or to
increase the speed of any fans.
82
Page 37
Installation
Extraction of the combustion products
The combustion products may be extracted
by means of hoods connected to a natural
draught chimney whose efficiency is certain
or via forced extraction. An efficient
extraction system requires precision
planning by a specialist qualified in this
area and must comply with the positions
and clearances indicated by the applicable
standards.
When the job is complete, the installer must
issue a certificate of conformity.
5.2 Adaptation to different types of
gas
In case of operation with other types of gas,
the burner nozzles must be changed and
the minimum flame adjusted on the gas
taps.
Replacing nozzles
1. Remove the grids, burner caps and
flame-spreader crowns to access the
burner casings.
2. Replace the nozzles using a 7 mm
spanner according to the gas to be used
(see Burner and nozzle characteristics
tables).
EN
1 Extraction using a hood
2 Extraction without a hood
A Single natural draught chimney
B Single chimney with extractor fan
C Directly outdoors with wall- or window-
mounted extractor fan
D Directly outdoors through wall
Air
Combustion products
Extractor fan
3. Reposition the burners in their correct
seats.
83
Page 38
Installation
Adjusting the minimum setting for natural
or city gas
Light the burner and turn it to the minimum
position. Extract the gas tap knob and turn
the adjustment screw next to the tap rod
(depending on the model) until the correct
minimum flame is achieved.
Refit the knob and verify that the burner
flame is stable. Turn the knob rapidly from
the maximum to the minimum setting: The
flame should not go out. Repeat the
operation on all gas taps.
Adjusting the minimum setting for LPG
Tighten the screw located at the side of the
tap rod clockwise all the way.
Following adjustment to a gas
other than the one originally set in
the factory, replace the gas setting
label on the appliance with the
one corresponding to the new gas.
The label is inserted inside the
nozzle pack (where present).
Lubricating the gas taps
Over time the gas taps may become difficult
to turn and get blocked. Clean them
internally and replace the grease.
Lubrication of the gas taps should
be performed by a specialised
technician.
84
Page 39
Gas types and Countries
Gas types IT GB-IE FR-BE DE AT NL ES PT SE RU DK
1 Natural Gas G20
G20 20 mbar
G20/25 20/25 mbar
2 Natural Gas G25
G25 25 mbar
3 Natural Gas G25
G25 20 mbar
4 LPG G30/31
G30/31 28/37 mbar
G30/31 30/37 mbar
G30/31 30/30 mbar
5 LPG G30/31
G30/31 50 mbar
6 City Gas G110
G110 8 mbar
7 City Gas G120
G120 8 mbar
Installation
•• •• •••••
•
•
•
•• • •
••
•••
••
•••
•
EN
85
Page 40
Installation
Burner and nozzle characteristics tables
1 Natural Gas G20 AUX SR R UR2
Rated heating capacity (kW)
Nozzle diameter (1/100 mm)
Pre-chamber (printed on nozzle)
Reduced capacity (W)
2 Natural Gas G25 AUX SR R UR2
Rated heating capacity (kW)
Nozzle diameter (1/100 mm)
Pre-chamber (printed on nozzle)
Reduced capacity (W)
3 Natural Gas G25 AUX SR R UR2
Rated heating capacity (kW)
Nozzle diameter (1/100 mm)
Pre-chamber (printed on nozzle)
Reduced capacity (W)
4 LPG G30/31 AUX SR R UR2
Rated heating capacity (kW)
Nozzle diameter (1/100 mm)
Reduced capacity (W)
Rated capacity G30 (g/h)
Rated capacity G31 (g/h)
5 LPG G30/31 AUX SR R UR2
Rated heating capacity (kW)
Nozzle diameter (1/100 mm)
Pre-chamber (printed on nozzle)
Reduced capacity (W)
Rated capacity G30 (g/h)
Rated capacity G31 (g/h)
6 City Gas G110 AUX SR R UR2
Rated heating capacity (kW)
Nozzle diameter (1/100 mm)
Pre-chamber (printed on nozzle)
Reduced capacity (W)
7 City Gas G120 AUX SR R UR2
Rated heating capacity (kW)
Nozzle diameter (1/100 mm)
Pre-chamber (printed on nozzle)
Reduced capacity (W)
1.05 1.8 3.0 4.2
72 97 115 75 + 135
(X) (Z) (Y) (H1)+(H3)
400 500 800 1900
1.05 1.8 3.0 4.2
72 94 121 75 + 145
(F1) (Y) (F2) (H1)+(H3)
400 500 800 1900
1.05 1.8 3.0 4.1
77 100 134 80 + 145
(F1) (Y) (F3) (Y)+(H3)
400 500 800 1900
1.05 1.8 3.0 4.2
50 65 85 46 + 91
400 500 800 1900
76 131 218 305
75 129 214 300
1.05 1.8 3.0 4.2
43 58 70 43 + 70
(H2) (M) (S) (S1)+(H2)
400 500 800 1900
76 131 218 305
75 129 214 300
1.05 1.8 2.8 4.0
145 185 260 150 + 320
(8) (2) (3) -
400 500 800 1400
1.05 1.8 3.0 4.0
135 175 240 130 + 290
(8) (1) (3) -
400 500 800 1400
The nozzles not provided are available at Authorised Service Centres.
86
Page 41
Installation
5.3 Electrical connection
Power voltage
Danger of electrocution
• Have the electrical connection
performed by authorised technical
personnel.
• Use personal protective equipment.
• The appliance must be connected to
ground in compliance with electrical
system safety standards.
• Disconnect the main power supply.
• Do not pull the cable to remove the
plug.
• Use cables withstanding a temperature
of at least 90°C.
• The tightening torque of the screws of
the terminal supply wires must be 1.5 - 2
Nm.
General information
The appliance can work in the following
modes:
Pyrolytic model
• 220-240 V 1N~
EN
3 x 2.5 mm² three-core cable.
• 380-415 V 2N~
4 x 1.5 mm² four-core cable.
• 380-415 V 3N~
Check the grid characteristics against the
data indicated on the plate.
The identification plate bearing the
technical data, serial number and brand
name is visibly positioned on the appliance.
Do not remove this plate for any reason.
Perform the ground connection using a wire
that is 20 mm longer than the other wires.
5 x 1.5 mm² five-core cable.
Multifunction model
• 220-240 V 1N~
3 x 2.5 mm² three-core cable.
87
Page 42
Installation
5.4 Positioning
The values indicated above refer
to the cross-section of the internal
conductor.
The aforementioned power cables
are sized taking into account the
coincidence factor (in compliance
with standard EN 60335-2-6).
Fixed connection
Fit the power line with an omnipolar circuit
breaker in compliance with installation
regulations.
The circuit breaker should be located near
the appliance and in an easily reachable
position.
Connection with plug and socket
Make sure that the plug and socket are of
the same type.
Avoid using adapters and shunts as these
could cause overheating and a risk of
burns.
Heavy appliance
Danger of crushing injuries
• Position the appliance into the cabinet
cutout with the help of a second person.
Pressure on the open door
Risk of damages to the appliance
• Never use the oven door to lever the
appliance into place when fitting.
• Avoid exerting too much pressure on the
oven door when open.
Heat production during appliance
operation
Risk of fire
• Veneers, adhesives or plastic coatings
on adjacent furniture should be
temperature-resistant (no less than
90°C).
88
General information
This appliance may be installed next to
walls, one of which must be higher than the
worktop, at a minimum distance of 150 mm
from the side of the appliance, as shown in
figures A and C relative to the installation
classes.
Page 43
Installation
Any wall units positioned above the
worktop must be at a minimum distance of
at least 750 mm.
If a hood is installed above the hob, refer to
the hood instruction manual to ensure the
correct clearance is left.
Depending on the type of installation, this
appliance belongs to classes:
EN
A - Class 1
(Free-standing appliance)
B - Class 2 subclass 1
(Built-in appliance)
89
Page 44
Installation
C - Class 2 subclass 1
(Built-in appliance)
The appliance must be installed by
a qualified technician and
according to the regulations in
force.
1. Use the adjustable feet to level the
appliance until it is level and stable on
the ground.
2. Fasten a hook bolt (not supplied) into the
wall at a height (H) of 800 mm from the
floor.
Fastening to wall (where present)
Heavy appliance
Risk of damages to the appliance
• Insert the front feet first and then the rear
ones.
The fastening system provided must be
installed to ensure the appliance is stable. If
installed correctly, this system prevents the
appliance from tipping over.
90
3. Attach the snap hook to the chain
Page 45
Installation
4. Attach the end of the chain to the hook
bolt fastened in the wall.
5. Connect the snap hook to the
appropriate hole on the back of the
appliance.
Positioning and levelling the appliance
After making the electrical and/or gas
connections, properly level the appliance
on the floor to ensure better stability. Screw
or unscrew the bottom part of the foot until
the appliance is stable and level on the
floor.
Assembling the upstand
The upstand provided is an
integral part of the product; it must
be fastened to the appliance prior
to installation.
The upstand must always be positioned and
secured correctly on the appliance.
1. Position the upstand on the top, taking
care to line up holes A with holes B.
2. Secure the upstand to the top by
tightening screws C.
EN
91
Page 46
Loading...