SMA WINDY BOY 3600TL, WINDY BOY 5000TL User Manual
WB36TL_50TL-BEN101310 | IMEN-WB36_50TL | Version 1.0
EN
Wind Power Inverter
WINDY BOY 3600TL / 5000TL
User Manual
Installer contact
Symbols on the Inverter
Operation display.
An error has occurred. Please inform your installer immediately.
Bluetooth®. Bluetooth communication active.*
Symbols on the Type Plate
Warning: dangerous electrical voltage.
The inverter operates at high voltages. All electrical work
on the inverter must be carried out by qualied personnel
only.
Beware of hot surface.
The inverter can become hot during operation. Avoid contact during operation.
Please observe enclosed documentation.
The inverter must not be disposed of together with the household waste.
For more information on disposal, please see the installation guide included upon
delivery.
CE mark. The inverter complies with the requirements of the applicable EC
guidelines.
RAL quality mark for solar products. The inverter complies with the requirements of
the German Institute for Quality Assurance and Labeling.
Direct current (DC)
Alternating current (AC)
The inverter is protected against penetration by dust particles and water jets from
any angle.
The inverter is transformerless.
* The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use
of these marks by SMA Solar Technology AG is under license.
EXPLANATION OF SYMBOLS
AC
Abbreviation for "alternating current".
Bluetooth
Bluetooth is a radio technology that allows the inverter and other communication devices to
communicate with each other. Bluetooth communication does not require visual contact between
the devices.
DC
Abbreviation for "direct current".
Electronic Solar Switch (ESS)
The Electronic Solar Switch is part of the inverter's DC switch-disconnector. Electronic Solar Switch
must be securely inserted into the bottom of the inverter and may
only be removed by qualied personnel.
GLOSSARY
CONTACT
If you have technical problems, rst contact your installer. The following information is required in
order to provide you with the necessary assistance:
• Inverter device type
• Serial number of inverter
• Type of connected small wind turbine system
• Event number or display message of the inverter
• Optional equipment (e.g. communication devices)
SMA Solar Technology AG
Sonnenallee 1
34266 Niestetal, Germany
www.SMA.de/en
SMA Serviceline
Inverters: +49 561 9522 1499
Communication: +49 561 9522 2499
Fax: +49 561 9522 4699
E-Mail: Serviceline@SMA.de
Visual inspection
Check the inverters and the cables for visible external damage. Contact your installer if you nd any
damage. Do not perform any repair work yourself.
Maintenance and Cleaning
Have correct operation of the inverter regularly checked by your installer.
VISUAL INSPECTION, MAINTENANCE AND CLEANING
DANGER!
Electric shock from high voltage at inverter.
Even when no external voltage is present, there can still be high voltages in the device.
The following work must be carried out by qualied personnel only:
• Electrical installation
• Repairs
• Modication
CAUTION!
Risk of injury from touching the enclosure during operation.
Burns to the body.
• Only touch lid and display during operation.
CAUTION!
Yield loss due to poor heat dissipation.
• Do not place any objects on the enclosure.
SAFETY INSTRUCTIONS
DIAGRAM POWER DISPLAY
MEASUREMENT ACCURACY
The power and energy of the inverter are displayed in the three elds: Power, Day and Total. The
display is updated every ve seconds.
Power
Current inverter power output fed into the grid.
Day
The energy fed into the grid on this particular day. This means the
energy total from midnight to the current time.
Total
Total energy which the inverter has fed into the grid during its entire
operating time.
The inverter energy is shown as a diagram on the display. The
daily graph is displayed by default. The right-hand ashing bar of
the diagram represents the current hour. In case the inverter does
not feed any power into the grid for a prolonged period (e.g.
when the wind is calm), a gap is inserted into the graph. The bar
for the current hour is updated automatically every ve seconds.
After four seconds, the bar goes off for one second and then
displays the current value.
The display values may deviate from the actual values and must not be used as a basis for invoicing.
The inverter's measured values are required for the system management and to control the current to
be fed to the grid. The inverter does not have a calibrated meter.
GRAPHIC DISPLAY
PLANT OVERVIEW
Current output
Daily energy
Total energy generated since the inverter was installed
Text line for displaying an event
Graphical display of the inverter energy
The display updates the values of your small wind turbine every ve seconds.
Tapping on the cover:
• Activating the background illumination
• Switching from the energy values of the past 16 feed-in
hours to daily energy values of the past 16 days
• Switching through the line display
Failure
Contact installer
Switch open: no feeding
Switch closed: feeding
Grid voltage/current
Bluetooth connection with other devices
DC voltage/current
Grid event number
Event number, small wind turbine system
Event number, inverter
Power reduction due to excessive temperature
• Cleaning the fan
• Provide better ventilation for inverter
LED
Green LED is glowing: Operation
Green LED is ashing: Network connection conditions not yet reached.
Red LED is glowing: Failure: contact installer.
Blue LED is glowing: The inverter has been incorporated into a Bluetooth network and can
communicate with other devices with identical NetID.
Blue LED is ashing: The inverter was identied with Sunny Explorer by setting the "Find device"
parameter.
PRODUCT OVERVIEW
Top enclosure lid
Lower enclosure lid
Graphic display
Electronic Solar Switch
LEDs
Serial number
Identication of Windy Boy using type plate
Loading...