EN
Device for closing dead zones with SMA Bluetooth
Wireless Technology
SMA BLUETOOTH REPEATER
Installation Manual
®
BTREPIN-IA-IEN100211 | 98-0011811 | Version 1.1
SMA Solar Technology AG Table of Contents
Table of Contents
1 Information on this Manual. . . . . . . . . . . . . . . . . . . . . . . . . 5
2 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.1 Intended Use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.2 Target Group Qualification . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.3 Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3SMA Bluetooth Repeater . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.1 Range of Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.2 Function Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.3 Device Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4 Unpacking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.1 Scope of Delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.2 Identifying the SMA Bluetooth Repeater . . . . . . . . . . . . . . . . . 11
5 Mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.1 Selecting the Mounting Location. . . . . . . . . . . . . . . . . . . . . . . . 12
5.2 Mounting the SMA Bluetooth Repeater on the wall. . . . . . . . . 14
5.3 Mounting the SMA Bluetooth Repeater to a top-hat rail . . . . . 15
6 Electrical Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
6.1 Connect the SMA Bluetooth Repeater to the power supply
using the plug-in power supply . . . . . . . . . . . . . . . . . . . . . . . . . 16
6.2 Connecting the SMA Bluetooth Repeater to the power
supply using the Power Modul . . . . . . . . . . . . . . . . . . . . . . . . . 17
7 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
7.1 Setting the MODE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
7.2 Setting the NetID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
8 Maintenance and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Installation Manual BTREPIN-IA-IEN100211 3
Table of Contents SMA Solar Technology AG
9 Decommissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
9.1 Detaching the SMA Bluetooth Repeater from the wall . . . . . . . 20
9.2 Detaching the SMA Bluetooth Repeater from the top-hat rail. . 21
9.3 Disposing of the SMA Bluetooth Repeater . . . . . . . . . . . . . . . . 21
10 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
10.1 Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
10.2 Connection Quality. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
11 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
11.1 SMA Bluetooth Repeater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
11.2 Plug-in Power Supply (CINCON, TRG30R 120) . . . . . . . . . . . 27
12 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
13 Contact . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
4 BTREPIN-IA-IEN100211 Installation Manual
SMA Solar Technology AG Information on this Manual
1 Information on this Manual
Validity
This manual is valid for the SMA Bluetooth Repeater, firmware version V 0.18R, and higher.
Target Group
This manual is intended for skilled workers. Only qualified personnel are allowed to perform the tasks
set forth in this manual (see section 2.2"Target Group Qualification",page7).
Additional Information
Additional information is available at www.SMA.de/en:
Document Title Document Type
®
SMA Bluetooth
SMA Bluetooth
Practice
Symbols
Symbol Explanation
Wireless Technology Technical Description
®
Wireless Technology in
Indicates a hazardous situation which, if not avoided, will result in death
or serious injury.
Indicates a hazardous situation which, if not avoided, could result in death
or serious injury.
Indicates a hazardous situation which, if not avoided, could result in minor
or moderate injury.
Indicates a situation that can result in property damage if not avoided.
Technical Information
Indicates information that is important for a specific topic or objective, but
is not safety-relevant.
☐ Indicates a requirement for meeting a specific goal.
☑ Desired result.
✖ A problem that could occur.
Installation Manual BTREPIN-IA-IEN100211 5
Information on this Manual SMA Solar Technology AG
Typography
Typography Explanation Example
"light" Designates elements in a software
user interface or on a display or
• The value can be read in the
"Energy" field.
mentions device connections.
bold Designates elements that can be
selected or entered in a software
user interface or on a display.
> Designates multiple elements that
•Select Settings.
•Enter 10 in the "Minutes" field.
•Select Settings > Date.
should be selected in a software
user interface or on a display.
[Button/key] Designates buttons or keys that
•Select [Next].
should be selected or pressed.
Nomenclature
This manual refers to PV plants and small wind turbine systems collectively as "plants".
6 BTREPIN-IA-IEN100211 Installation Manual
SMA Solar Technology AG Safety
2Safety
2.1 Intended Use
The SMA Bluetooth Repeater may only be used with the following SMA Solar Technology AG
products:
• All SMA communication products with Bluetooth
•All inverters with SMA Bluetooth Piggy-Back upgrade
•All inverters with SMA Bluetooth Piggy-Back Plus upgrade
• Inverters with integrated Bluetooth:
– SB (Sunny Boy) 3000TL-20/SB 4000TL-20/SB 5000TL-20: from software package 2.06
– SB 3000TL-21/SB 4000TL-21/SB 5000TL-21
– SB 2000HF-30/SB 2500HF-30/SB 3000HF-30
– STP (Sunny Tripower) 10000TL-10/STP 12000TL-10/STP 15000TL-10/STP 17000TL-10
Only use the SMA Bluetooth Repeater indoors.
Information for France
In France, the SMA Bluetooth Repeater is only to be operated inside buildings due to the legal
regulations.
Only skilled workers may install and uninstall the SMA Bluetooth Repeater.
Only use the SMA Bluetooth Repeater in accordance with the information provided in the enclosed
documentation. Any other use can result in personal injury or property damage.
The enclosed documentation is a part of this product.
• Read and follow the documentation for the correct and optimum use of the
SMA Bluetooth Repeater.
• Keep the documentation in a convenient place at all times.
2.2 Target Group Qualification
A trained skilled worker has received training and demonstrated skills and knowledge regarding the
fu nct ion s and ope rat ion of th e de vic e. A skilled wor ker is tr ained to deal with the dangers and hazards
involved in installing electrical systems.
Installation Manual BTREPIN-IA-IEN100211 7
Safety SMA Solar Technology AG
2.3 Safety Instructions
Electric Shock
Risk of lethal electric shock when touching conductive parts of the inverter.
• Prior to performing any work on the inverter, disconnect the inverter on the AC and DC sides
(see inverter installation manual).
• Only skilled workers may work on the inverter.
Electrostatic Discharge (ESD)
By touching electronic component parts you can cause damage to or destroy the inverter through
electrostatic discharge (ESD).
• Ground yourself before touching a component part by touching the protective conductor (PE)
or a non-coated part of the inverter enclosure.
• Avoid coming into contact with component parts and plug contacts.
8 BTREPIN-IA-IEN100211 Installation Manual
SMA Solar Technology AG SMA Bluetooth Repeater
3SMA Bluetooth Repeater
3.1 Range of Usage
The SMA Bluetooth Repeater is used to close dead zones under unfavorable installation conditions
between SMA Solar Technology AG devices with Bluetooth Wireless Technology or to improve poor
wireless connections.
Figure1: Example for the use of the SMA Bluetooth Repeater
Position Description
A Communication device (here: Sunny Beam with Bluetooth)
BSMA Bluetooth Repeater
C SMA Solar Technology AG inverter with Bluetooth
3.2 Function Overview
• Connection to SMA devices with Bluetooth Wireless Technology via Bluetooth Class 1.
• Maximum range of up to 100 m in free-field conditions with direct visual contact. In closed
rooms the range is dependent on several factors.
Installation Manual BTREPIN-IA-IEN100211 9
SMA Bluetooth Repeater SMA Solar Technology AG
3.3 Device Overview
Figure2: Overview of the device elements
Position Description
A Plug-in power supply connection (AC)
B DC source connection (e.g. Power Modul, see section 12"Accessories",page28)
C"RDY" LED for power supply (green)
D"MODE" rotary switch
E"NetID" rotary switch
F Bluetooth LED (blue)
G Connection quality LEDs (yellow)
10 BTREPIN-IA-IEN100211 Installation Manual
SMA Solar Technology AG Unpacking
4 Unpacking
4.1 Scope of Delivery
Check the delivery for completeness and for any visible damage. Please contact your retailer if the
delivery is incomplete or you find any damage.
Figure3: Components included in delivery
Position Quantity Description
A1 SMA Bluetooth Repeater
B 1 Bracket for wall mounting or top-hat rail mounting
(Is connected to the rear side of the SMA Bluetooth Repeater for
delivery)
C1Screw
D1Screw anchor
E 1 2-pole plug for the connection of the power supply via the
Power Modul
4.2 Identifying the SMA Bluetooth Repeater
You can identify the SMA Bluetooth Repeater via the type label. The type label is on the right-hand
side of the SMA Bluetooth Repeater.
Installation Manual BTREPIN-IA-IEN100211 11
Mounting SMA Solar Technology AG
200 mm
150 mm
100 mm100 mm
340 mm
425 mm
5Mounting
5.1 Selecting the Mounting Location
Observe the requirements for the mounting location or installation location:
☐ The mounting location is indoors.
☐ The device is protected against dust, moisture and corrosive substances at the mounting
location.
☐ Minimum clearances have been observed.
Minimum Clearances:
Figure4: Minimum clearances to be observed
• If you are using a plug-in power supply, select a mounting location close to a socket-outlet.
• If you are using the Power Modul, observe the maximum cable length of 10 m for the power
supply.
• Keep a distance of at least 1 m from devices that use the 2.4 GHz frequency band, e.g. WLAN
devices or microwave ovens. This will prevent reduced connection quality and data transmission
speed.
Determining the Mounting Location or Installation Location
Determine the mounting location or installation location by changing the distance between the
SMA Bluetooth Repeater and the devices with critical connection quality until all devices show at least
a good connection quality.
12 BTREPIN-IA-IEN100211 Installation Manual
SMA Solar Technology AG Mounting
Requirements:
☐The "MODE" rotary switch is at position "0" (see section 7.1"Setting the MODE",page18).
☐The "NetID" rotary switch is set to the NetID of the plant (see section 7.2"Setting the
NetID",page18).
Risk of lethal electric shock when touching conductive parts of the inverter.
• Prior to performing any work on the inverter, disconnect the inverter on the AC and DC sides
(see inverter installation manual).
• Only skilled workers may work on the inverter.
1. Decommission the plant (see the manual of the inverter and of the communication product).
Thus, you ensure that the SMA Bluetooth Rep eat er i s in tegrate d in to t he S MA Bluetooth n etw ork
at the point where the dead zone thus improving the Bluetooth connection at that point.
2. Position the SMA Bluetooth Repeater half way between the devices with a critical connection
quality.
3. Connect the power supply (see section 6"Electrical Connection",page16).
4. Recommission the plant (see the manual of the inverter and of the communication product).
5. Repeat the plant search with the communication device (see the communication product
manual, e.g. Sunny Beam with Bluetooth, Sunny Explorer).
6. Check that the connection quality for all devices is at least "good". For this, all devices must be
in their usual positions (e.g. the Sunny Beam may not be held directly in front of the
SMA Bluetooth Repeater):
Product "Good" connection quality
SMA Bluetooth Repeater 1 blue and 2 yellow LEDs are on
Sunny Boy of the type SB x000TL-2x and
SB xx00HF-30, Sunny Tripower of the type
At least 2 rings are shown in the
inverter display
STP 1x000TL-10
SMA inverter of other types with
SMA Bluetooth Piggy-Back or
Check whether the connection quality improves
through the use of the SMA Bluetooth Repeater
SMA Bluetooth Piggy-Back Plus
Communication device
See the respective manual
(e.g. Sunny Beam with Bluetooth)
Sunny Explorer Move the mouse cursor over the radio symbol at
the lower right of the user interface
☑ The connection quality of all devices is at least "good". Mount or install the
SMA Bluetooth Repeater at this location.
✖ The connection quality of all devices is not at least "good"?
Installation Manual BTREPIN-IA-IEN100211 13
Mounting SMA Solar Technology AG
15 mm
60 mm
70 mm70 mm
• Position the SMA
Bluetooth
Repeater at another location and re-check the connection
qualities.
• If necessary install additional SMA Bluetooth Repeaters.
5.2 Mounting the SMA Bluetooth Repeater on the wall.
Mounting accessories required:
•1 Bracket
•1 Screw
• 1 Screw anchor
1. Remove the bracket from the guide rail on the rear
side of the SMA Bluetooth Repeater. Lift the
bracket via the strap and press against the guide
rail.
2. Mark the drill hole. Observe the distances
between the drill hole and the enclosure sides.
3. Drill a hole with a diameter of 6 mm at the position
marked.
4. Affix the bracket to the wall using the screw anchor
and the screw. Align the bracket so that both pins
point upwards and the SMA logo faces to the
front.
14 BTREPIN-IA-IEN100211 Installation Manual
SMA Solar Technology AG Mounting
CLICK
5. Plug the SMA Bluetooth Repeater from the top
onto the bracket. Observe the orientation of the
SMA logo on the enclosure.
☑The SMA Bluetooth Repeater snaps audibly into
place.
5.3 Mounting the SMA Bluetooth Repeater to a top-hat rail
Mounting accessories required:
•1 Bracket
1. Pull the bracket using the strap and pull it out of the guide rail on the rear side of the
SMA Bluetooth Repeater until only half of the bracket is still locked in place. The bracket slightly
protrudes over the enclosure edge.
2. Hook the SMA Bluetooth Repeater from below
onto the top-hat rail.
3. Push the SMA Bluetooth Repeater upwards onto
the top-hat rail.
4. Push the SMA Bluetooth Repeater downwards.
5. Pu sh t he brack et i nto the guid e ra il u ntil the bra cke t
completely snaps into place.
Installation Manual BTREPIN-IA-IEN100211 15
Electrical Connection SMA Solar Technology AG
6 Electrical Connection
6.1 Connect the SMA Bluetooth Repeater to the power supply using the plug-in power supply
Danger of fire due to incorrect plug-in power supply
Technically unsuitable plug-in power supplies may cause a short circuit or a fire.
• Use the plug-in power supply intended as an accessory for the SMA Bluetooth Repeater.
1. Connect the country-specific socket-outlet adapter to the plug-in power supply; it snaps into
place when inserted correctly.
2. Insert the plug-in power supply plug into the "Power 12V" terminal of the
SMA Bluetooth Repeater.
3. Plug the plug-in power supply mains plug into the socket-outlet.
☑The "RDY" LED on the SMA Bluetooth Repeater lights up. The SMA Bluetooth Repeater is
connected to the power supply.
✖The "RDY" LED is not lit or is blinking?
• See section 10.1"Power Supply",page22.
16 BTREPIN-IA-IEN100211 Installation Manual
SMA Solar Technology AG Electrical Connection
6.2 Connecting the SMA Bluetooth Repeater to the power supply using the Power Modul
Risk of lethal electric shock when opening the inverter
Death or serious injuries
• Disconnect the inverter on the AC and DC side (see inverter installation manual).
Electrostatic discharge can damage the inverter
• Ground yourself before touching component parts by touching the protective conductor (PE)
or a non-coated part of the inverter enclosure.
Requirement:
☐ The Power Modul is installed in the inverter (see Power Modul manual).
1. Disconnect and open the inverter (see inverter installation manual).
2. Open the spring terminals of the 2-pole plug.
3. Connect the insulated conductors to the spring terminals. For this purpose, the polarity is
arbitrary.
4. Close the spring terminals.
5. Recommission the inverter with installed Power Modul (see inverter manual).
6. Insert the 2-pole plug into the "Power 12V" terminal on the SMA Bluetooth Repeater.
☑The "RDY" LED on the SMA Bluetooth Repeater lights up. The SMA Bluetooth Repeater is
connected to the power supply.
✖The "RDY" LED is not lit or is blinking?
• See section 10.1"Power Supply",page22.
Installation Manual BTREPIN-IA-IEN100211 17
Settings SMA Solar Technology AG
7 Settings
7.1 Setting the MODE
The "MODE" rotary switch is set to the position "0" for delivery. Other positions are not permitted and
are intended for SMA Service only.
•If the "MODE" rotary switch is not set to the correct position, turn the arrow of the "MODE"
rotary switch to the correct position using a 2.5 mm screwdriver.
7.2 Setting the NetID
Plants with SMA Bluetooth operating in close proximity to one another are distinguished by their
individual NetID. All devices in a plant must have the same NetID. You can set the
SMA Bluetooth Repeater to the NetID of your plant using the "NetID" rotary switch.
Assignment of the rotary switch positions
NetID Function
0 Bluetooth is switched off.
1
(Status upon delivery)
Bluetooth is switched on.
The device can connect to a maximum of 2 communication products. The
device cannot establish a connection to other inverters or
SMA Bluetooth Repeaters.
2 to 9 and A to F Bluetooth is switched on.
The device can interlink with all SMA Bluetooth products having the same
NetID.
*
See section 10.2 for information on the status of the Bluetooth LEDs.
*
NetID 1 is possible for plants with 1 inverter
You may leave the default NetID set to 1 in your inverter if your Bluetooth plant consists of the
following products:
• Maximum 1 inverter
• Maximum 1 computer with Bluetooth and the Sunny Explorer software
• Maximum 1 Sunny Beam of the type BEAM-BT-11.GR1
or
• Maximum 1 inverter
• Maximum 2 Sunny Beams of the type BEAM-BT-11.GR1
In all other cases you must determine a free NetID (see Sunny Explorer Help).
• If the plant NetID is not known, read off the NetID from one of the devices in the plant
(e.g. Sunny WebBox with Bluetooth or inverter with Bluetooth).
• Use a 2.5 mm screwdriver to turn the arrow of the "NetID" rotary switch to the plant NetID.
18 BTREPIN-IA-IEN100211 Installation Manual
SMA Solar Technology AG Maintenance and Care
8 Maintenance and Care
• Regularly check whether the SMA Bluetooth Repeater is externally damaged or soiled.
•If the SMA Bluetooth Repeater is externally damaged to a degree that impairs correct
functioning, replace the SMA Bluetooth Repeater.
•If the SMA Bluetooth Repeater is soiled, clean the SMA Bluetooth Repe ater u sing on ly a slight ly
damp cloth. Only use a non-abrasive and non-acidic cleaning agent.
Installation Manual BTREPIN-IA-IEN100211 19
Decommissioning SMA Solar Technology AG
9 Decommissioning
9.1 Detaching the SMA Bluetooth Repeater from the wall
1. Disconnect the SMA Bluetooth Repeater from the power supply.
•If the SMA Bluetooth Repeater is connected to the plug-in power supply, pull the mains plug
from the socket-outlet and remove the plug-in power supply plug from the
SMA Bluetooth Repeater.
•If the SMA Bluetooth Repeater is connected to the Power Modul, disconnect and open the
inverter with installed Power Modul (see inverter installation manual) and remove the
2-pole plug from the "Power 12V" terminal on the SMA Bluetooth Repeater.
2. Push the SMA Bluetooth Repeater upwards and
use a screwdriver to press it against the bracket.
3. Slide the SMA Bluetooth Repeater upwards away from the bracket.
4. Unscrew the screw from the wall and remove the bracket.
5. If the SMA Bluetooth Repeater was connected to the Power Modul, remove the cable
connection from the Power Modul (see Power Modul manual).
20 BTREPIN-IA-IEN100211 Installation Manual
SMA Solar Technology AG Decommissioning
9.2 Detaching the SMA Bluetooth Repeater from the top-hat rail
1. Disconnect the SMA Bluetooth Repeater from the power supply.
• If the SMA
the socket-outlet and remove the plug-in power supply plug from the SMA
•If the SMA Bluetooth Repeater is connected to the Power Modul, disconnect and open the
inverter with installed Power Modul (see inverter installation manual) and remove the
2-pole plug from the "Power 12V" terminal on the SMA Bluetooth Repeater.
2. Push the SMA Bluetooth Repeater downwards
and use a screwdriver to press it against the
bracket. Pull the bracket downwards and remove.
3. Tilt the l ower edge o f the SMA Bluetooth Repeater
forwards.
4. Remove the SMA Bluetooth Repeater upwards
from the top-hat rail.
Bluetooth
Repeater is connected to the plug-in power supply, pull the mains plug from
Bluetooth
Repeater.
5. If the SMA Bluetooth Repeater was connected to the Power Modul, remove the cable
connection from the Power Modul (see Power Modul manual).
9.3 Disposing of the SMA Bluetooth Repeater
• Observe the disposal regulations for electronic waste that apply at the installation site when
disposing of the SMA Bluetooth Repeater.
• To have SMA Solar Technology AG dispose of the SMA Bluetooth Repeater:
– Use packaging which adequately protects the device from damage during transport.
Hint: If available, use the original packaging.
– Send the SMA Bluetooth Re pea ter back to S MA S ola r Techno log y AG at y our own cost wit h
the information "ZUR ENTSORGUNG" ("FOR DISPOSAL").
Installation Manual BTREPIN-IA-IEN100211 21
Troubleshooting SMA Solar Technology AG
10 Troubleshooting
10.1 Power Supply
"RDY" LED
Status Meaning Measure
Glows green
continuously
Flashes green
and all other
LED are unlit.
Flashes green
and all other
LEDs are
flashing
The power supply is good.
The SMA Bluetooth Repeater is
operating.
Power supply is marginal.
The SMA Bluetooth Repeater is
operating.
The SMA Bluetooth Repeater
firmware is defective.
None
If you are using a plug-in power supply:
• Use only the plug-in power supply that is
intended as an accessory for the
SMA Bluetooth Repeater.
If you are using the Power Modul:
• If you are using the SMA cable included in
the delivery:
– Contact the SMA Serviceline.
• If you are using a different cable:
– Improve the power supply via one of
the following measures:
– Shorten the cable.
– Choose a larger cable cross-section.
• Contact the SMA Serviceline.
22 BTREPIN-IA-IEN100211 Installation Manual
SMA Solar Technology AG Troubleshooting
"RDY" LED
Status Meaning Measure
Off No power supply or the power
supply is too low.
The SMA Bluetooth Repeater is
not operating.
If you are using a plug-in power supply:
Check whether the wall plug is supplying
electricity.
• Connect a different device to the socketoutlet, for example.
If the socket-outlet is providing electricity,
then either the plug-in power supply or the
SMA Bluetooth Repeater is defective.
– Replace the plug-in power supply.
– Replace the SMA Bluetooth Repeater.
If you are using the Power Modul:
• If you are using the SMA cable included in
the delivery:
– Contact the SMA Serviceline.
• If you are using a different cable:
– Check the wiring.
If the wiring is correct, either the Power
Modul or the SMA Bluetooth Repeater is
defective.
– Contact the SMA Serviceline.
Installation Manual BTREPIN-IA-IEN100211 23
Troubleshooting SMA Solar Technology AG
10.2 Connection Quality
The SMA Bluetooth Repeater can only display the connection quality if it is integrated into an existing
SMA Bluetooth network. The Bluetooth network is only established by master devices
always shows the connection quality to the device that established the connection to it.
Bluetooth LEDs
Status Measure
Blue LED Yellow LEDs Connection quality
Very good None
Permanently on 3 LEDs are
permanently lit
Good None
2 LEDs are
permanently lit
Unreliable • Change the position of the
1 LED is
permanently lit
Critical
SMA Bluetooth Repeater.
or
• Install additional
SMA
3 LEDs are not lit
Off 3 LEDs are not lit
The SMA Bluetooth
Repeater is not connected
to the Bluetooth network.
• Check the NetID.
• Change the position of the
SMA
or install additional
There is no device with the
SMA
same NetID within the
radio range.
The SMA Bluetooth
network has not been
established. Network
• Commission a master in
the SMA Bluetooth
network.
establishment is only
triggered by masters, e.g.
communication products.
The "NetID" rotary switch
3 LEDs flashing
*
Master is a network engineering term. In a network, a master is a device that requests other devices (slaves)
to receive or send data, for example. All communication products (e.g. Sunny Explorer, Sunny Beam with Bluetooth) are masters
in an SMA Bluetooth network.
is set to position "1" or "0".
• Set the "NetID" rotary
switch to the NetID of your
plant (see section 7.2).
*
Bluetooth
Bluetooth
Bluetooth
. A device
Repeaters.
Repeater
Repeaters.
24 BTREPIN-IA-IEN100211 Installation Manual
SMA Solar Technology AG Troubleshooting
Bluetooth LEDs
Status Measure
Blue LED Yellow LEDs Connection quality
flashes
3 LEDs flashing
The SMA Bluetooth
Repeater firmware is
defective.
•Contact the
SMA Serviceline.
and the "RDY"
LED flashes
green
Installation Manual BTREPIN-IA-IEN100211 25
Technical Data SMA Solar Technology AG
11 Technical Data
11.1 SMA Bluetooth Repeater
General Data
Width x height x depth 142 mm x 40 mm x 76 mm
Weight 144 g
Mounting location indoors
Mounting type Top-hat rail/wall mounting bracket
Status display LEDs
Degree of protection (IP)
*
According to IEC 60529
*
Power Supply
AC power supply Plug-in power supply
Power supply DC Power Modul
AC input voltage 12 V … 24 V
Tolerance value for AC input voltage ± 10%
Frequency of AC input voltage 50 Hz / 60 Hz
DC input voltage 12 V … 24 V
Tolerance value for DC input voltage ± 20%
Typical power consumption 0.8 W
Maximum power consumption 1.2 W
IP20
Environmental Conditions in Operation
Ambient temperature –20°C … +65°C
Relative humidity, non condensing 5% … 95%
Altitude above mean sea level (MSL) 0 m … 3 000 m
Ambient Conditions during Storage/Transport
Ambient temperature –40°C … +70°C
Relative humidity, non condensing 10% … 95%
Altitude above mean sea level (MSL) 0 m … 3 000 m
26 BTREPIN-IA-IEN100211 Installation Manual
SMA Solar Technology AG Technical Data
Communication
Inverter Bluetooth
Data logger Bluetooth
Range in open air ≤ 100 m
11.2 Plug-in Power Supply (CINCON, TRG30R 120)
Mechanical Data
Width x Height x Depth 107.8 mm x 57.5 mm x 33.5 mm
Weight 300 g
Power Supply
Voltage 100 V − 240 V AC,
50 Hz / 60 Hz
Nominal current 0.8 A
Installation Manual BTREPIN-IA-IEN100211 27
Accessories SMA Solar Technology AG
12 Accessories
You will find the corresponding accessories and spare parts for your product in the following
overview.
If required, you can order these at SMA Solar Technology AG or your retailer.
Description Brief description SMA order number
Plug-in power supply for
Europe, USA and Canada
Plug-in power supply for
Australia and Korea
Power Modul Module for the power supply of
Plug-in power supply for
SMA Bluetooth Repeater,
Sunny WebBox, SMA Power
Injector with Bluetooth,
RS485-Power Injector and
Wireless-Set 485-01/02
Plug-in power supply for
SMA Bluetooth Repeater,
Sunny WebBox, SMA Power
Injector with Bluetooth,
RS485-Power Injector and
Wireless-Set 485-01/02
the SMA Bluetooth
Repeater
via the inverter.
PWRSUPPLY
PWRSUPPLY/AU/KR
PWRM-10-NR
28 BTREPIN-IA-IEN100211 Installation Manual
SMA Solar Technology AG Contact
13 Contact
If you have technical problems concerning our products, contact the SMA Serviceline. We need the
following information in order to provide you with the necessary assistance:
• Type, serial number and firmware version of the inverter
• Serial number of the communication product
• Firmware version or software version of the communication product
• Serial number and firmware version of the SMA Bluetooth Repeater
SMA Solar Technology AG
Sonnenallee 1
34266 Niestetal, Germany
www.SMA.de
SMA Serviceline
Inverters +49 561 9522 1499
Communication: +49 561 9522 2499
Fax: +49 561 9522 4699
E‑Mail: Serviceline@SMA.de
Installation Manual BTREPIN-IA-IEN100211 29
SMA Solar Technology AG Legal Restrictions
The information contained in this document is the property of SMA Solar Technology AG. Publishing its content, either partially or
in full, requires the written permission of SMA Solar Technology AG. Any internal company copying of the document for the
purposes of evaluating the product or its correct implementation is allowed and does not require permission.
Exclusion of liability
The general terms and conditions of delivery of SMA Solar Technology AG shall apply.
The content of these documents is continually checked and amended, where necessary. However, discrepancies cannot be
excluded. No guarantee is made for the completeness of these documents. The latest version is available online at www.SMA.de
or from the usual sales channels.
Guarantee or liability claims for damages of any kind are excluded if they are caused by one or more of the following:
• Damages during transportation
• Improper or inappropriate use of the product
• Operating the product in an unintended environment
• Operating the product whilst ignoring relevant, statutory safety regulations in the deployment location
• Ignoring safety warnings and instructions contained in all documents relevant to the product
• Operating the product under incorrect safety or protection conditions
• Altering the product or supplied software without authority
• The product malfunctions due to operating attached or neighboring devices beyond statutory limit values
• In case of unforeseen calamity or force majeure
The use of supplied software produced by SMA Solar Technology AG is subject to the following conditions:
• SMA Solar Technology AG rejects any liability for direct or indirect damages arising from the use of software developed by
SMA Solar Technology AG. This also applies to the provision or non-provision of support activities.
• Supplied software not developed by SMA Solar Technology AG is subject to the respective licensing and liability agreements
of the manufacturer.
SMA Factory Warranty
The current guarantee conditions come enclosed with your device. These are also available online at www.SMA.de and can be
downloaded or are available on paper from the usual sales channels if required.
Trademarks
All trademarks are recognized even if these are not marked separately. Missing designations do not mean that a product or brand
is not a registered trademark.
The Bluetooth
Solar Technology AG is under license.
SMA Solar Technology AG
Sonnenallee 1
34266 Niestetal
Germany
Tel. +49 561 9522-0
Fax +49 561 9522-100
www.SMA.de
E-Mail: info@SMA.de
© 2004 to 2011 SMA Solar Technology AG. All rights reserved
Installation Manual BTREPIN-IA-IEN100211 31
®
wor d mark an d logos a re registe red trad emarks own ed by Blu etoo th SIG , Inc. an d any use of such mar ks by SMA
XXX4."4PMBSDPN
4."4PMBS5FDIOPMPHZ
4."4PMBS5FDIOPMPHZ"(
XXX4."EF
4.""NFSJDB--$
XXX4.""NFSJDBDPN
4."5FDIOPMPHZ"VTUSBMJB1UZ-UE
XXX4.""VTUSBMJBDPNBV
4."#FOFMVY413-
XXX4."#FOFMVYDPN
4."#FJKJOH$PNNFSDJBM$P-UE
XXX4."$IJOBDPN
4."$[FDI3FQVCMJDTSP
XXX4."$[FDIDPN
4."'SBODF4"4
XXX4."'SBODFDPN
4.")FMMBT"&
XXX4.")FMMBTDPN
4."*C©SJDB5FDOPMPHB4PMBS4-
XXX4."*CFSJDBDPN
4."*UBMJB4SM
XXX4."*UBMJBDPN
4."5FDIOPMPHZ,PSFB$P-UE
XXX4.",PSFBDPN
Loading...