ESD-200/ESD-250 I.I. — Rev. 0 (12/02)
Code No. 0816549
INSTALLATION INSTRUCTIONS
SENSOR OPERATED
ELECTRONIC SOAP DISPENSER
Model ESD-200
Deck Mounted
Plug-in Transformer Powered
Sensor Operated
Electronic Soap Dispenser
Model ESD-250
Deck Mounted
Battery Powered
Sensor Operated
Electronic Soap Dispenser
For Soap Replenishment use:
Sloan Part No. ESD-217 (800 ml Bottle)
Can also be used with TC® OneShot® Soap Cartridges (TC Stock #401311)
To order Replacement Soap Cartridges:
1-800-700-CLEAN (1-800-700-2532)
Or go to our website: www.optimasoap.com
Refills are also available through you local plumbing or janitorial supply distributor.
Installation of the Sloan ESD-200 and ESD-250, Sensor Operated Electronic Soap Dispenser makes soap dispensing totally "hands-free" providing the ultimate in sanitary protection and automatic operation. The Electronic Soap Dispenser uses infrared technology to sense the user's presence and dispense an application of hand washing soap. The ESD-200 Soap Dispenser is powered by a plug-in transformer (included). The ESD-250 Soap Dispenser is powered by four "D" cell batteries (included) which eliminates the need to run any electrical lines to the system.
The Sloan ESD-200 and ESD-250, Sensor Operated Electronic Soap Dispenser comes complete with an integral spout and sensor assembly, control module, soap cartridge and all mounting hardware.
The following instructions will serve as a guide when installing the Sloan ESD-200 and ESD-250 Electronic Soap Dispenser. As always, good safety practices and care are recommended when installing your new Soap Dispenser. If further assistance is required, contact your nearest Sloan Representative office or the Sloan Installation Engineering Department.
LIMITED WARRANTY
Sloan Valve Company warrants its ESD-200 and ESD-250 Electronic Soap Dispenser to be made of first class materials, free from defects of material or workmanship under normal use and to perform the service for which they are intended in a thoroughly reliable and efficient manner when properly installed and serviced, for a period of three years (1 year for special finishes) from date of purchase. During this period, Sloan Valve Company will, at its option, repair or replace any part or parts which prove to be thus defective if returned to Sloan Valve Company, at customer’s cost, and this shall be the sole remedy available under this warranty. No claims will be allowed for labor, transportation or other incidental costs. This warranty extends only to persons or organizations who purchase Sloan Valve Company’s products directly from Sloan Valve Company for purpose of resale. This warranty does not cover the life of the batteries (Model ESD-250 only).
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT IS SLOAN VALVE COMPANY RESPONSIBLE FOR ANY CONSEQUENTIAL DAMAGES OF ANY MEASURE WHATSOEVER.
PRIOR TO INSTALLATION
New Soap Dispenser Installation:
•Locate position using templates shown in rough-in diagrams (refer to Pages 2 and 5)
•Ensure that dispenser does not interfere with anything above or below the lavatory/counter top area (refer to Page 5)
•Drill a 1” diameter hole in counter top (use template on Page 5)
•Clean area around hole
Replacing Existing Soap Dispenser:
•Remove old components
•Clean Area
•Ensure hole is 15/16” to 1-1/4” diameter
SOAP DISPENSER ROUGH-IN (Refer to page 5 for template)
1-13/16” |
5-3/8” |
(46 mm) |
(137 mm) |
|
|
|
|
4-1/4” |
|
|
|
|
(108 mm) |
|
|
1/32” |
|
|
|
|
(1 mm) |
|
|
BRASS |
15/16” |
HOLE |
1” |
|
SHANK |
(24 mm) |
|
(25 mm) |
3-5/16” |
|
|
|
|
|
|
|
|
|
(84 mm) |
|
|
|
|
FLANGE |
FLANGE |
ADJUST TO |
|
|
NUT |
NUT |
COUNTER |
|
|
|
|
|
6-15/16” |
|
|
|
|
(176 mm) |
|
|
SENSOR
14-1/16”
(357 mm)
2-31/32”
(75 mm)
1-5/8”
(41 mm)
1/8” (3 mm)
SINK
1 |
- |
1/2” |
mm) |
|
||
|
(38 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
4-1/4”
(108 mm)
COUNTER
FLANGE
NUT
2
Loading...