Sloan AD-81000 Installation Manual
AER-DEC™-81000/82000/83000/84000
Integrated Sink System
Single/Double/Triple/Quadruple Station Corian® or Quartz Lavatory Systems
Installation
Instruction
Code No. 0816672
Rev.2 (04-15)
AD-81000
Deck Sink Lavatory System
Corian/Quartz (Pages 2-3)
AD-82000
Deck Sink Lavatory System
Corian/Quartz (Pages 4-5)
IMPORTANT
Read this entire installation manual to ensure proper installation.
When nished with the installation, le this manual with the owner
or maintenance department. Compliance and conformity to local
codes and ordinances is the responsibility of the installers.
Separate parts from packaging and make sure all parts are
accounted for before discarding any packaging material. If any
parts are missing, do not begin installation until you obtain the
missing parts.
Make sure that all water supply lines have been ushed and then
completely turned off before beginning installation. Debris in supply
lines can cause valves to malfunction.
PRIOR TO INSTALLATION
Important:
• Adequate structural support in or behind the wall is required. Refer to the
appropriate rough-in diagram for dry weight of sink.
Refer to pages 10 and 11 for sink and stud support requirements.
AD-83000
Deck Sink Lavatory System
Corian/Quartz (Pages 6-7)
Turn OFF electrical power to the electrical outlets, then unplug all
electrical units prior to installation. Electrical power MUST remain
off until installation is complete.
Installer’s hardware must be appropriate for wall construction. Wall
anchors must have a minimum pull-out rating of 1,000 lbs.
For standard height mounting, do not exceed the recommended
34” distance from the top of the lav deck to the nished oor. To
meet ADA requirements, the lav deck cannot exceed the
34” maximum height dimension.
Wear all proper safety equipment prior to installation.
• All plumbing should be installed in accordance with applicable
codes and regulations.
• Before connecting ex hoses to supply stops, ush all water lines until
water is clear.
• Hot and cold water supply lines/tempered supply line & drain lines.
AD-84000
Deck Sink Lavatory System
Corian/Quartz (Pages 8-9)
SUPPLIES REQUIRED FOR INSTALLATION OF SINKS
• 3/8” x 2 1/2” lag screws, wall anchors, bolts (minimum pull-out rating of
1000 Ibs./450 kg). See Frame Mounting Support drawing for required lag
screws for your specic lavatory system.
• 1/2” NPT hot/cold or tempered supply piping
• 1 1/2” NPT drain piping
LIMITED WARRANTY
Unless otherwise noted, Sloan Valve Company warrants its Products to be made of rst class materials, free from defects of material or workmanship under normal use and to
perform the service for which they are intended in a thoroughly reliable and efcient manner when properly installed and serviced, for a period of three years (1 year for SF Faucets, special nishes and PWT electronics and 30 days on PWT software) from date of purchase. During this period, Sloan Valve Company will, at its option, repair or replace
any part or parts which prove to be thus defective if returned to Sloan Valve Company, at customer’s cost, and this shall be the sole remedy available under this warranty. No
claims will be allowed for labor, transportation or other incidental costs. This warranty extends only to persons or organizations who purchase Sloan Valve Company’s products
directly from Sloan Valve Company for purpose of resale. This warranty does not cover the life of the batteries.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT IS SLOAN VALVE COMPANY RESPONSIBLE FOR
ANY CONSEQUENTIAL DAMAGES OF ANY MEASURE WHATSOEVER.
• Adhesive: Loctite
Adhesive
• 110 volt GFCI protected electrical outlet for 100-120 VAC plug-in transformer
• Screen lter(s) included with faucet(s)
• Backing supplied by others to meet local codes
®
PL Premium® FAST GRAB Polyurethane Construction
1
LAVATORY SYSTEM ROUGH-IN DIMENSIONS FRONT VIEW SINGLE STATION
LAVATORY SYSTEM ROUGH-IN PLUMBING & ELECTRICAL DIMENSIONS FRONT VIEW SINGLE STATION
LAVATORY SYSTEM ROUGH-IN DIMENSIONS SIDE VIEW SINGLE STATION
2
LAVATORY SYSTEM ROUGH-IN DIMENSIONS TOP VIEW SINGLE STATION
12”
6”
1/2” Backing
DRAIN ASSEMBLY AND FRAME ENCLOSURE MOUNTING SUPPORT SINGLE STATION
Drywall
2”x10” wood
reinforcement
between studs
Wood Stud per schedule
33"
GFI 4 gang outlet
Backing supplied by others
to meet local codes
Hand Dryer Blower Motor
w/ Mufer Attachment
Lag Bolts
1. Measure outside of frame.
Cut-out drywall window
2. Remove drywall window.
3. Replace with backing supplied by
Frame Enclosure
Hidden drain w/clean-out
Grid strainer to be cleaned
out as required
others (per local code).
4. Using mounting template, mount
blower motor, soap dispenser pump
(optional) and electrical outlets to
backing.
5. Mount top of frame at 33” above
nished oor.
6. Securely fasten with 1,000 Lb
pull out lag bolts.
12”
6”
*Hole Location for
Soap Dispenser
*Due to manufacturing
tolerances, all dimensions
are for reference only.
Mounting Frame
12”
12”
MOUNTING FAUCETS, SOAP DISPENSERS & HAND DRYERS / ATTACHING DECK TO FRAME ENCLOSURE SINGLE STATION
1. For ease of installation, leave the
deck laying on its back. Install
faucets, optional soap dispensers and hand dryers according
Adhesive
MOUNTING FAUCETS
For ease of installation,
leave the deck laying on its back.
Install faucets, optional soap dispensers
and hand dryers according to
manufacturers instructions.
FRAME SUPPORT
1. Back edge of Deck may require scribing to nished wall.
2. Shim all gaps between frame and deck,
especialy under trough area.
BASYS DRYER SPOUT
SUBASSEMBLY
HOLDING NUT
ASSEMBLY
CONNECT CONTROL
CABLE TO BLOWER
HAND DRYER
Refer to installation instructions with
component.
EHD-510
BAYONET TURN
TO LOCK HOSE
TO SPOUT
PROGRAMING
CABLE. LEAVE
UNATTACHED
CONNECT GROUND
WIRE TO BLOWER
WALL UNIT BLOWER
MOTOR ASSEMBLY
HOSE & MUFFLER
ASSEMBLY
BAYONET TURN
TO LOCK HOSE TO
BLOWER
to manufacturers instructions.
2. Hook-up air hose to blowers. Do
not connect power until air spout
is completely installed.
3. Install all water connections,
drain lines and components.
BASYS SOAP SPOUT
SUBASSEMBLY
HOLDING NUT
ASSEMBLY
SOAP DISPENSER
LINES
SOAP DISPENSER
Refer to installation instructions with
component.
ESD-400
POWER ADAPTOR
SOAP DISPENSER
MOTOR ASSEMBLY
3
LAVATORY SYSTEM ROUGH-IN DIMENSIONS FRONT VIEW DOUBLE STATION
to local code.
Notes:
1. Mount Blower and Soap Dispenser to spec. location.
2. Slip frame over mounted components and properly fasten frame to
backed wall.
3. Hot and Cold water supply lines location subject
LAVATORY SYSTEM ROUGH-IN PLUMBING & ELECTRICAL DIMENSIONS FRONT VIEW DOUBLE STATION
LAVATORY SYSTEM ROUGH-IN DIMENSIONS SIDE VIEW DOUBLE STATION
4
Loading...