Slendertone Arms Instruction Manual

Slendertone Arms US IM Rev 2 Backup_Layout 1 29/03/2016 12:28 Page 3

Your SLENDERTONE product is intended to stimulate healthy muscles in order to improve
or facilitate muscle performance of the triceps and biceps muscles. Your SLENDERTONE
product is suitable for use by all healthy adults; however, as with other forms of exercise,
some care is needed when using it. Always follow the guidelines below and read the
instruction manual before use. Some of the points below are gender-specific.

Contra-indications:
Do not use if:

• You h av e an e le ct ro n ic i mp la nt ( e. g. c a rdi a c pa ce ma ke r or d ef i br il la to r - as y ou r product
may interfere with the proper functioning of the implanted stimulator) or suffer from any
other heart problem.

• You have any other form of medical implant. The safety has not been established for
the use of electronic muscle stimulators over medical implants.

• You are pregnant. The safety of electronic muscle stimulation (EMS) over the pregnant
uterus has not been established.

• Yo u su ff er fro m ca nc er. T he eff ec ts o f el ec tro ni c st im ul at ion on cancero us t is su e are
unknown.

• You are under medical supervision for cognitive dysfunction as you may not be able to
comply with safety instructions.

• The controller is in close proximity (e.g., 1 yard) to shortwave or microwave therapy
equipment or you are connected to high-frequency surgical equipment (e.g.
diathermy), because of the risk of device malfunction due to electronic interference.

• Wearing the product necessitates placement over areas at which drugs/medicines
are administered (short-term or long-term) by injection (e.g., hormone treatment

S).

Warnings:

• The long-term effects of chronic electronic stimulation are unknown.

• The product Should not be used while sleeping, because you cannot react to safety

information.

When applying the GelPads™ and garments, always remember to:

• Place the GelPads and garments ONLY as indicated in this manual.

• Avoid placing the GelPads or garments on the front or sides of the neck, across or
through the heart (i.e., one GelPad on the front of the chest and one on the back), in

the genital region or on the head, because of the risk of stimulating inappropriate muscles
and organs.

• Avoid application of GelPads near the thorax, as this may increase the risk of cardiac
fibrillation.

• Avoid any recent scars, broken or inflamed skin, areas of infection or susceptibility to
acne, thrombosis or other vascular problems (e.g., varicose veins), or any parts of the
body where feeling is limited.

• Avoid areas of injury or restricted movement (e.g., fractures or sprains).

• Avoid placing the GelPads over metal implants. They may be placed on the nearest
muscle.

Precautions:

• You should only use this product while in a relaxed, seated position, with your arms
bent slightly and resting in your lap.

• Do not straighten your arms during the session, as this can lead to an ineffective session
and may cause some discomfort.

• Never use the product while invloved in any activity which includes using your arms or
hands.

• Your arms are likely to move involuntarily during a session.

• Keep your controller in your hands during each session.

• Do not fasten the straps too tightly around your arms.

• If the garment leads are damaged or exposed, they should be replaced immediately.

• Maximum use of a

SLENDERTONE product is one session per day per body area.

• Caution should be used for patients with suspected or diagnosed epilepsy.

• Caution should be used in the following:

- When there is a tendency to bleed internally following an injury or fracture.

- Following recent surgical procedures when electronic stimulation may disrupt the
healing process

- Over areas of skin which lack normal sensation

• Your

SLENDERTONE product Is not intended for medical use, for the treatment of any

medical condition, nor for any permanent physical changes.

• You should only use SLENDERTONE GelPads as other kinds may reduce the effectiveness
of the exercise.

CONTRA-INDICATIONS, WARNINGS & PRECAUTIONS

2

Slendertone Arms US IM Rev 2 Backup_Layout 1 29/03/2016 12:28 Page 4

Get your doctor’s permission before using your SLENDERTONE product if:

• You have any serious illness or injury not mentioned in this guide.

• You have recently undergone a surgical procedure.

• You take insulin for diabetes.

• You want to use it on a young child.

• You suffer from muscle or joint problems.

• You use the product as part of a rehabilitation program.

Adverse reactions:

• Skin irritations and burns have been reported with the use of powered muscle
stimulators.

• On very rare occasions, first-time users of EMS have reported feeling light-headed
or faint. We recommend that you use the product while seated until you become
accustomed to the sensation.

To reposition the GelPads during a session:

• Always pause the program currently running, unfasten the strap and then refasten it
around your arm after the GelPads’ positions have been adjusted.

After strenuous exercise or exertion:

• Always use a lower intensity to avoid muscle fatigue.

Contact

SLENDERTONE or an authorized dealer if:

• Your product is not working correctly. Do not use in the meantime.

• You experience any irritation, skin reaction, hypersensitivity, or other adverse reaction.
You should, however, note that some reddening of the skin under the garment is quite
normal during and for a short time after an exercise session.

Note:

• An effective session should not cause undue discomfort.

Important:

• Keep your controller out of the reach of children.

• The studs and GelPads must not be connected to other objects.

• Do not use the product at the same time as any other device which transfers an
electrical current into the body (e.g., another muscle stimulator).

• Do not touch the GelPads or metal studs while the controller is switched on.

• Do not use while driving, operating machinery or cycling or during any activity in which
involuntary muscle contractions may put the user at undue risk of injury.

• The garments are for single person use only.

• Cease using your product if you are feeling light headed or faint. Consult your doctor if
this happens

• Do not over exert yourself when using muscle stimulation. Any workout should be at a
level comfortable for you.

• Although compliant with applicable EMC requirements, this device may stil interfere
with more sensitive equipment, please move away or turn off.

•

SLENDERTONE will not accept responsibility if the guidelines and instructions supplied

with this product are not followed.

Note: If you are in any doubt about using your SLENDERTONE product for any reason,
please consult your doctor before use.

3

English

Slendertone Arms US IM Rev 2 Backup_Layout 1 29/03/2016 12:28 Page 5

Congratulations on purchasing SLENDERTONE

ARMS

and taking the first step towards

firmer, stronger and more defined arms.

SLENDERTONE, a company with almost 50

years experience in the medical device
industry, is proud to offer you this product.
You are now on the way to the body shape
you’ve always dreamed of, so don’t waste
another minute - set-up your

SLENDERTONE

ARMS and enjoy your first session right now!

WELCOME WHY YOU’LL LOVE IT

At SLENDERTONE we are proud to have delivered a clinically proven arm product that delivers results.
Your

SLENDERTONE ARMS uses patented EMS Technology, where a signal is sent to the nerves, through

the GelPads, which in turn contracts the biceps and triceps muscles.

SLENDERTONE ARMS is an electronic muscle stimulator intended to stimulate healthy muscles in order to

improve or facilitate muscle performance of the triceps and biceps muscles of the upper arms.

MAKING IT WORK FOR YOU

To get the most from your

SLENDERTONE ARMS, follow the 30-day plan and use your SLENDERTONE ARMS 3

times a week at an intensity level comfortable for you. We recommend you leave at least 48 hours
between sessions. Use as part of a normal, healthy lifestyle.

Read all instuctions fully before use!

4

Slendertone Arms US IM Rev 2 Backup_Layout 1 29/03/2016 12:28 Page 6

THE SCIENCE BEHIND SLENDERTONE

Your SLENDERTONE ARMS uses SLENDERTONE’S patented C.S.I.
Technology to deliver signals directly to your neuromuscular
system, causing contractions which exercise and tone your
muscles.

Step 1: Signals are sent through the GelPads. The signals activate
the nerves which control the biceps and triceps muscles.

Step 2: As the signal strength increases, the nerves, in turn,
cause your muscles to contract and relax rhythmically.

The Result: A deep, effective muscle workout. It’s like

SLENDERTONE

does the hard work for you!

BICEPS TRICEPS

1

2

5

4

3

5

English

WHAT’S IN THE BOX

These are the contents for the SLENDERTONE ARMS pack.

1.

SLENDERTONE ARMS Controller

2. Arm Garments

3. Medical Grade GelPads

4. Battery Charger

5. Instruction Literature

Slendertone Arms US IM Rev 2 Backup_Layout 1 29/03/2016 12:28 Page 7

1. On/Off Button ( )

Press and hold this button for 2 seconds to
turn your controller on or off. You may also
pause the exercise by briefly pressing this
button.

2. Increase Training Intensity ( )

Press and hold these buttons to increase
the intensity of the exercise. The right-hand
button controls the garment on your right
arm. The left-hand button controls the
garment on your left arm.

3. Decrease Training Intensity ( )

Press and hold these buttons to decrease the
intensity of the signal to either arm.

4. Program Button ( P )

Press this button to select the program you wish to use.
There are 3 programs, which are explained later in this manual (page 9).

5. Information Button ( i )

Press this button to see your training information, such as the maximum
intensity for your current or last session and the number of sessions you
have completed.

Training intensity from the left arm garment.
Training intensity from the right arm garment.
Counts down the time left in the current session. Also displays error

messages (see page 10).
Appears when the exercise has been paused.
Indicates that the sound is off.
Keylock is active - you cannot change the intensity levels or the program

accidentally.
This symbol indicates a poor contact betwe en the controller and

garments or between the GelPads and the skin (see page 11 for
more details).

Shows the battery power remaining.
Number of sessions completed.
Shows the program currently running (1 - 3).
This symbol appears during each contraction phase.
Maximum intensity for the current/ last session.

1.

2.

3.

5.

4.

DISPLAY

CONTROLS CONTROLLER DISPLAY

6

Slendertone Arms US IM Rev 2 Backup_Layout 1 29/03/2016 12:28 Page 8

5

CHARGE YOUR CONTROLLER

1. Insert your charger into a socket and then connect your controller to it. It will
take approximately 2-3 hours to fully charge the battery. Your controller is fully
charged when all three sections of the battery icon are full. The battery icon
will flash when the battery is low and needs to be recharged.

2. Always diconnect your controller from the charger when the battery is fully
charged.

GARMENT SET-UP

3. Connect the controller to the garments. The controller and garments
must be connected properly for your

SLENDERTONE ARMS to work. “Click” the

controller connector into the garment connector.

4. Place the garments with the four silver studs facing towards you. Remove
the adhesive GelPads from their pack. You will notice that one side of each
GelPad has a grid pattern on it while the other side is black.

5. Remove the covers from the patterned side of the four GelPads. Place
the patterned side of the GelPads over the silver studs and within the white
lines.

6. Remove the covers from the black side of all four GelPads. Do not throw
these away as you will need to put them back onto the GelPads at the end
of your session.

I

MPORTANT:

Before you increase the intensity, make sure that all of the silver studs are
completely covered by the GelPads. Press the edges of each one firmly onto the
material before use. You should only use

SLENDERTONE GelPads as other kinds

may reduce the effectiveness of the exercise.

3

6

4

1

2

7

English

Slendertone Arms US IM Rev 2 Backup_Layout 1 29/03/2016 12:28 Page 9

When you have completed your session, remove the garments,
replace the covers on the black side of the GelPads and store
the product safely until your next session.

IMPORTANT:

Always ensure the controller is switched off before removing the
garments.

Have any further questions? Just call our Toll Free number:
1-800-551-2443 or visit the website: www.slendertone.com

POSITIONING THE GARMENTS CORRECTLY

1. Take the garment marked ‘R’ and place the larger section centrally over
the triceps muscle of your RIGHT arm. Ensure the wider part is towards
your elbow.

2. Then, bring the strap around the OUTSIDE of your arm and place the
small, oval section centrally over your biceps muscle. Then fasten the
strap securely, but comfortably, around your arm.

3. Repeat steps 1 and 2, placing the garment marked ‘L’ onto your LEFT
arm.

4. Switch on your controller by pressing the On/Off button for 2 seconds.
Select the program you wish to use and increase the intensity to a strong,
comfortable level.

Note: You may feel a tingling sensation in your lower arms during a session.
Simply changing the position of your arms can reduce this. If it persists,
pause the controller and adjust the position of the arm garments slightly.

1

2

4

3

8

Slendertone Arms US IM Rev 2 Backup_Layout 1 29/03/2016 12:28 Page 10

Record the highest intensity levels in your performance plan (see back of this
instruction manual). The diary below shows one persons plan. Each box shows
the highest training intensity for each arm garment. The intensity level will vary
from person to person. Fill in the diary each time you complete a training session.
Leave your diary somewhere you will see it regularly. This will help to motivate you
to reach your goal.

Your SLENDERTONE ARMS has three programs.

1. Conditioning is a moderate strength program, introducing the biceps and
triceps muscles to this form of training. This should be used before progressing
to the stronger programs.

2. Strength is a stronger program and will strengthen your biceps and triceps
muscles as well as improving muscle performance.

3. Power is a longer power program, using short, powerful contractions to
increase both maximum muscle strength and sustained performance of the
biceps and triceps muscles simultaneously.

• Once you have selected a program, the controller will continue using that

program until you change it.

• We recommend you use the product no more than three times a week and

that you leave at least 48 hours between sessions.

Note: You cannot change a program during a session, you must switch your
controller off and then on again. You can then select a different program by
pressing the program button.

Week 1 Session 1 Session 2 Session 3

Week 2 Session 1 Session 2 Session 3

Week 3 Session 1 Session 2 Session 3

Week 4 Session 1 Session 2 Session 3

SLENDERTONE ARMS PROGRAMSTRACK YOUR PROGRESS

Program Duration Intensity

Conditioning 10 minutes 0-99
Strength 12 minutes 0-99
Power 15 minutes 0-99

Program

Number

PERFORMANCE PLAN

LEFT
ARM

RIGHT

ARM

9

English

Slendertone Arms US IM Rev 2 Backup_Layout 1 29/03/2016 12:28 Page 11

Information Button ( i )

Press the information button (Fig. a) any time during a
session to see the highest intensity level you have reached
for that session. Pressing the information button twice
shows you the total number of sessions you have
completed. While pressing the information button three
times identifies the product type you are using.

Mute Function ( )

If you want to switch off your product’s sound effects,
press and hold the program button for two seconds
(Fig. b). The mute function remains active indefinitely
unless manually changed. Deactivate the mute function
by again pressing the program button for two seconds

Keylock Function ( )

If you find a comfortable exercise intensity, press and
hold the information button for two seconds to lock
that intensity (Fig. c). This function only remains active
during the session in which it is activated. If you wish
to increase the intensity further, deactivate the keylock
function by again pressing the information button for
two seconds.

Error Messages

In the unlikely event of your product developing a problem,
“Err” will appear on the display (Fig. d). If this occurs you
should switch the controller off and then switch it back
on again. It should now operate properly. If the problem
persists, please call Customer Care for further assistance:
Tel: [phone]
Email: [e-mail]

Battery Power / Replacing the battery

The battery icon on the display will flash when the
battery is low and needs to be recharged. After a period
of time, you may find that your battery will only power
your controller for a limited number of sessions, requiring
you to charge the battery more frequently. This is because
rechargeable batteries have a limited number of charge
cycles and may eventually need to be replaced.

Should you need to replace the rechargeable battery,
remove the small rubber plug from the back cover of
your controller (Fig. e), unscrew the back cover and
remove it. Replace the existing battery pack with a
new battery pack (Fig. f) and replace the battery cover.
You can purchase a new battery pack by visiting
www.slendertone.com or calling Customer Care on
1-800-551-2443.

Fig. a

Fig. b

Fig. c

ADDITIONAL FUNCTIONS

Fig. d

Fig. e

Fig. f

10

Slendertone Arms US IM Rev 2 Backup_Layout 1 29/03/2016 12:28 Page 12

If you have problems getting your SLENDERTONE ARMS to work, you should go
through the following checklist:

Have you charged your battery?

It takes 2-3 hours to fully charge your battery

Is your charger fully connected?

Push the charger connector and controller connector together
until they “click” into place.

Is your controller connected to the garment properly?

Check to ensure that it is connected properly. To remove, press
the outer buttons on the connector and reinsert again.

When did you last change your GelPads?

GelPads need to be changed every 20-30 sessions. Visit
www.slendertone.com or call Customer Care to order replace­ment GelPads.

Have you removed all the plastic covers from both the grid
and black sides of the GelPads?

Remember to keep one set of covers to protect the black side of
the GelPads during storage.

Are the GelPads covering the metal studs?

Double-check the GelPads on your belt to ensure that the grid
side of each pad is fully covering the metal studs.

Has the GelPad Contact symbol ( ) appeared on the display? *

The controller and garments are not properly connected. The symbol
always appears in conjunction with the left/right intensity indicators. If the
left indicator appears, there is a problem with the left-arm garment, the
right indicator acknowledges a problem with the right-arm garment. If both
indicators appear there is a problem with both garments.

Still having trouble? Visit our website or call Customer Care:

Web: www.slendertone.com
Tel: [phone]
Email: [e-mail]

Your garments may be cleaned using a lightly dampened sponge, but you must first
remove the GelPads. Always follow the cleaning instructions when cleaning the garments.

Never machine-wash or hand-wash your garments. Always clean them using a
lightly dampened cloth or sponge.

Do not use bleach when washing the garments.

Do not dry clean your garments.

Do not tumble dry your garments. Dry them on a flat surface. Do not dry them over
anything hot. (e.g. a radiator) as they contain plastic parts. Ensure the garments
are completely dry before using them again.

The garments should never be ironed.

TROUBLESHOOTING CHECKLIST

CARING FOR YOUR GARMENTS

11

English

Slendertone Arms US IM Rev 2 Backup_Layout 1 29/03/2016 12:28 Page 13

The stimulation is uncomfortable. How can I improve this?

• Make sure the GelPads are positioned correctly and that they are pressed
firmly against your skin - see pages 7-8. Switch off your controller and
reposition the garments if necessary.

• You can also smear a few drops of water on the black side of the GelPads.
This can improve the comfort of the muscle stimulation, but be careful not
to get water on the controller. Ensure the controller is switched OFF before
you do this!

• Ensure the metal studs are fully covered by the GelPads.

My skin is red after the exercise. Is this a problem?

• Some redness of the skin after a training session is normal. It is partly due
to an increase in the blood flow under the skin and should fade after a while.
You may also experience some reddening of the skin due to the pressure of
the garments. This is the same as the pressure marks you can get from tight
clothing. You should not be concerned about this. It should fade soon after
you remove them.

• If the redness is excessive, you may have the training intensity too high. This
may increase the reddening in sensitive skin. Try using a lower intensity for a
few days. If the problem persists, you should stop using the product.

Will the product cause muscle soreness?

• As with all exercise some muscle soreness can occur after using your

SLENDERTONE ARMS. This is normal and should go away after a while. Use

a low intensity for a few sessions if you are experiencing muscle soreness.

How do I know when to replace the GelPads?

• With time the GelPads pick up skin debris and may need to be replaced as
this makes the workout less effective and less comfortable.

• You may notice the signal is weakening even if the battery is fully charged.
This usually indicates that the gel pads are wearing and will soon need
replacing. You can check this by first adjusting the belt to ensure correct
positioning of the gel pads. If the signal is still weak or uncomfortable, you
should order new gel pads.

• New GelPads can be purchased online at www.slendertone.com (check for
special offers) or from customer care.

Battery performance has degraded significantly.

• After an extended period of time you may notice a degradation in the
performance of the battery in your controller. At this point you should
purchase a new rechargeable battery pack. New rechargeable battery
packs can be purchased by visiting www.slendertone.com or by calling
Customer Care at 1-800-551-2443.

FREQUENTLY ASKED QUESTIONS

12

Slendertone Arms US IM Rev 2 Backup_Layout 1 29/03/2016 12:28 Page 14

PRODUCT WARRANTY

Dear Customer,
Thank you for purchasing your

SLENDERTONE product ("Product"). To be covered by this Limited

Warranty, the Product must have been purchased directly from Slendertone Distribution,
Inc. ("SDI"), or its authorized retailer in the United States. This Limited Warranty extends only
to the original purchaser and cannot be transferred to anyone. Please read this carefully
before using the Product.

Our Limited Warranty to you

SDI

WARRANTS TO YOU, THE ORIGINAL PURCHASER, THAT UNDER NORMAL USE AND SERVICE, THE

PRODUCT WILL BE FREE FROM DEFECTS IN MATERIAL AND WORKMANSHIP FOR A PERIOD OF TWO (2)

YEAR FROM THE DATE OF PURCHASE ("WARRANTY PERIOD"). IF YOU DISCOVER A DEFECT COVERED BY
THIS LIMITED WARRANTY DURING THE WARRANTY PERIOD, AND RETURN THE PRODUCT TO US, WE WILL
REPAIR OR REPLACE THE PRODUCT, AT OUR OPTION, USING NEW OR REMANUFACTURED COMPONENTS.

THERE IS NO WARRANTY OR CONDITION OF ANY KIND AS TO ANY DEFECTS DISCOVERED AFTER THE
WARRANTY PERIOD EXPIRES.

Certain Product failures not covered

This Limited Warranty covers defects in manufacture that arise from correct use of the Product
per the product manual and instructions. It does not cover damage caused by abuse, misuse,
accidents, modification or repair by any person other than SDI, moisture, extreme heat or
cold, corrosive environments, high voltage surges from external sources or an unsuitable
power supply. This Limited Warranty does not cover normal wear and tear on consumable
items (e.g. GelPads, garments, etc.). This Limited Warranty does not apply to any battery
provided with the Product, or if the Product has an altered or defaced serial number.

How to obtain service under this Limited Warranty

To o bt ai n s e rv ic e u n de r th is L im it ed Wa r ra nt y, p le as e c o nt ac t S DI ’s Cu st o me r Ca re a t
1-800-551-2443 to obtain return instructions. You must submit proof of purchase in the
form of a bona fide, dated bill of sale, receipt, or invoice (or copy thereof) evidencing that
your request for service is made within the Warranty Period.

Except as may otherwise be required by legislation in your State, SDI will not be responsible
for the cost of returning the Product or for any damage to or loss of the Product while it is
in transit to us.

We recommend that you use a carrier that will track your shipment and ensure the Product’s
safe delivery. SDI cannot accept any returns sent C.O.D.

THIS LIMITED WARRANTY IS THE ONLY WARRANTY FOR THE PRODUCT, AND
THERE ARE NO OTHER EXPRESS WARRANTIES, ORAL OR WRITTEN, PROVIDED
BY SDI. ANY IMPLIED WARRANTIES APPLICABLE TO THE PRODUCT, INCLUDING
ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PUR­POSE, ARE LIMITED TO THE DURATION OF THE WARRANTY PERIOD SET FORTH
ABOVE.

Limitation of Remedies
YOUR EXCLUSIVE REMEDY, IN LIEU OF ALL INDIRECT, INCIDENTAL, CONSEQUENTIAL,
EXEMPLARY, SPECIAL OR OTHER DAMAGES OF ANY KIND, INCLUDING FOR
NEGLIGENCE, IS LIMITED TO THE REPAIR OR REPLACEMENT OF THE PRODUCT,
IF DEFECTIVE, UNDER THE TERMS AND CONDITIONS OF THIS LIMITED WARRANTY.

SDI will bear no other expenses.
SDI reserves the right to refuse to repair or replace the Product if it is returned in an
unsanitary condition. SDI reserves the right to substitute a product of equal or better quality
if an identical product is not available at the time of replacement. This Limited Warranty is
non-transferable.

Applicability of state law

Some states do not allow limitations on the duration of implied warranties, or the exclusion
or limitation of incidental or consequential damages, and so the related limitations and
exclusions stated above may not apply to you.

Governing law

This Limited Warranty is valid in the United States only and is not applicable in other
countries. If you acquired the Product in the United States, the laws of the State of New
York will apply to this Limited Warranty.

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY
ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE.

13

English

Slendertone Arms US IM Rev 2 Backup_Layout 1 29/03/2016 12:28 Page 15

Caring for your controller

Your controller should not be allowed to get wet or be left in excessive sunlight. It may
be cleaned regularly using a soft cloth, lightly dampened in soapy water. Do not allow
the interior of your controller to become wet. Do not use detergents, alcohol, spray
aerosols or strong solvents on your controller.

Access to the interior of the controller is not required for maintenance purposes.

If your product is damaged, you should not use it but should return it to

SLENDERTONE or

your local distributor for replacement or repair. Repairs, service and modifications may
not be carried out by anyone other than qualified service personnel authorized by

SLENDERTONE.

IMPORTANT: Under no circumstance should anything other than the correct type of batteries

(rechargeable batteries 3.6V NiMH) be used with your controller. These can be purchased
from SLENDERTONE Customer Care.

Disposing of the GelPads and batteries

Used GelPads and batteries must never be disposed of in a fire but in accordance with
national or state laws governing the disposal of such items.

NOTES: The signal gradually increases to a peak intensity level at the start of the contraction

phase (i.e. ramp up) and gradually decreases to nothing at the start of the relaxation phase
(i.e. ramp down). When the symbol is flashing, the stimulus is significantly reduced.

Product Type: 397

Intended use: Muscle stimulator

Classification: Internally powered equipment, Class II charger, Type BF applied parts.

Waveform: Symmetrical bi-phasic square waveform when measured into a resistive

load.

Accessories:

You can purchase accessories at www.slendertone.com. Under no circumstances
should anything other than

SLENDERTONE accessories be used with your SLENDERTONE

charger or SLENDERTONE controller (Type 390). Any others may not be compatible with
your product and could degrade the minimum safety levels.

SLENDERTONE ARMS GelPads: • 4 GelPads (Type 718)

Battery Pack (3.6V, NiMH)
Battery Charger:
EU: 2504-0321 + 2504-0324 + 2504-0325; US/Japan: 2504-0322;
Australia: 2504-0321 + 2504-0327; Korea: 2504-0321 + 2504-0323

Charger complies to EN 60950, Input: nominal voltage 100-240V, frequency 50-60Hz,
current 125mA. Do not use any other chargers or any other power supplies.

Environmental Specifications:
Operating Range: Temperature: 32 - 95°F

Humidity: 20 - 65 % RH

Transport & Temperature: 32 - 131°F
Storage Range: Humidity: 10 - 90 % RH

Attention:

This product can deliver currents in excess of 2mA/cm

2

if used with incorrect electrodes.

TECHNICAL SPECIFICATIONS

14

Slendertone Arms US IM Rev 2 Backup_Layout 1 29/03/2016 12:28 Page 16

Description of your controller’s symbols:

There are a number of technical markings on your controller. These can be explained as
follows:

The product is manufactured in China for Bio-Medical Research Ltd,
Parkmore Business Park West, Galway, Ireland.

The controller requires 1 x 3.6 volt (NiMH) DC battery pack. DC is indicated by the
symbol:

The Output Frequency indicates the number of pulses per second transmitted by the
controller. This is measured in hertz, which is indicated by “Hz”.

Output (RMSA) means the maximum output root mean square current for each channel.

Output (RMSV) means the maximum output root mean square voltage for each channel.

This symbol means “Attention, consult the accompanying documents”.

This symbol means type BF applied parts (GelPads).

Conforms to UL STD 60601-1.
Certified to CAN/CSA.
STD C22.2 NO 601.1

SN stands for ‘serial number’. On the label on the back of the controller is the serial
number specific to this product. The letter preceding the number indicates the year of
manufacture, where “U” denotes 2015, “V” denotes 2016 etc.

The garment’s batch number is represented on the garment packaging, by the number
corresponding with the LOT symbol.

Rated Outputs – Voltage/Currents: X:60
Parameter 500! 1K! 1K5!

Output RMSV 3.8V 7V 7.9V
Output RMSA 7.7mA 7mA 5.3mA
Output Frequency 50Hz 50Hz 50-Hz
DC Component: Approx. 0 C 0 C 0 C
Positive Pulse Width: 100-125µs 100-125µs 100-125µs
Negative Pulse Width: 100-125µs 100-125µs 100-125µs
Interphase Interval: 100 µs 100 µs 100 µs

At the end of the product lifecycle, do not throw this product into the normal
household garbage, but bring it to a collection point for the recycling of electronic
equipment.

Some product materials can be re-used if you bring them to a recycling point.
By re-using some parts or raw materials from used products you make an
important contribution to the protection of the environment. Please contact your
local authorities if you need more information about collection points in your area.

Waste Electrical and Electronic Equipment can have potentially harmful effects
on the environment. Incorrect disposal can cause harmful toxins to build up in the
air, water and soil and can be harmful to human health.

Garment Materials:
Outer Material: 80% Nylon, 20% polyester
Inner Material: 100% Polyester laminated to 100% polyurethane
Binding: 100% Nylon
Hook & Loop: 100% Nylon
Foam: EVA
Elasticated Straps: 100% Nylon.

!

15

English

Slendertone Arms US IM Rev 2 Backup_Layout 1 29/03/2016 12:28 Page 17