Singer PG-D3010X User Manual

Download

DATA PROJECTOR

Introduction

MODEL

PG-D3510X PG-D3010X PG-D2710X

OPERATION MANUAL

Easy Start

Setup

Connections

Operation

Basic

Features

Useful

Appendix

IMPORTANT

• For your assistance in reporting the loss or theft of your Projector, please record the Model and Serial Number located on the bottom of the projector and retain this information.

• Before recycling the packag ing, please ensure that you have checked the contents of the carton thoroughly against the list of “Supplied accessories” on page

11.

Model No.:

Serial No.:

SPECIAL NOTE FOR USERS IN THE U.K.

The mains lead of this product is ﬁ tted with a non-rewireable (moulded) plug incorporating a 10A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked of the plug, must be used. Always reﬁ t the fuse cover after replacing the fuse. Never use the plug without the fuse cover ﬁ tted. In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the mains plug and ﬁ t an appropriate type.

DANGER:

The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a safe manner. Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet, as a serious electric shock may occur. To ﬁ t an appropriate plug to the mains lead, follow the instructions below:

WARNING:

THIS APPARATUS MUST BE EARTHED.

IMPORTANT:

The wires in this mains lead are coloured in accordance with the following code:

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows:

The wire which is coloured green-and-yellow must be connected to the terminal in the

•

The wire which is coloured blue must be connected to the terminal which is marked

•

The wire which is coloured brown must be connected to the terminal which is marked

•

or and of the same rating as above, which is also indicated on the pin face

Green-and-yellow : Earth Blue : Neutral Brown : Live

plug which is marked by the letter E or by the safety earth symbol or green-and-yellow.

with the letter N or coloured black.

with the letter L or coloured red.

or coloured green

IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.

Authorized representative responsible for the European Union Community Market

SHARP ELECTRONICS (Europe) GmbH Sonninstraße 3, D-20097 Hamburg

E.U. ONLY

iii

The supplied CD-ROM contains operation instructions in English, German, French, Spanish, Italian, Dutch, Swedish, Portuguese, Chinese, Korean and Arabic. Carefully read through the operation instructions before operating the projector.

Die mitgelieferte CD-ROM enthält Bedienungsanleitungen in Englisch, Deutsch, Französisch, Spanisch, Italienisch, Niederländisch, Schwedisch, Portugiesisch, Chinesisch, Koreanisch und Arabisch. Bitte lesen Sie die Bedienungsanleitung vor der Verwendung des Projektors sorgfältig durch.

Le CD-ROM fourni contient les instructions de fonctionnement en anglais, allemand, français, espagnol, italien, néerlandais, suédois, portugais, chinois, coréen et arabe. Veuillez lire attentivement ces instructions avant de faire fonctionner le projecteur.

El CD-ROM suministrado contiene instrucciones de operación en inglés, alemán, francés, español, italiano, holandés, sueco, portugués, chino, coreano y árabe. Lea cuidadosamente las instrucciones de operación antes de utilizar el proyector.

Il CD-ROM in dotazione contiene istruzioni per l’uso in inglese, tedesco, francese, spagnolo, italiano, olandese, svedese, portoghese, cinese, coreano e arabo. Leggere attentamente le istruzioni per l’uso prima di usare il proiettore.

De meegeleverde CD-ROM bevat handleidingen in het Engels, Duits, Frans, Spaans, Italiaans, Nederlands, Zweeds, Portugees, Chinees, Koreaans en Arabisch. Lees de handleiding zorgvuldig door voor u de projector in gebruik neemt.

Den medföljande CD-ROM-skivan innehåller bruksanvisningar på engelska, tyska, franska, spanska, italienska, holländska, svenska, portugisiska, kinesiska, koreanska och arabiska. Läs noga igenom bruksanvisningen innan projektorn tas i bruk.

O CD-ROM fornecido contém instruções de operação em Inglês, Alemão, Francês, Espanhol, Italiano, Holandês, Sueco, Português, Chinês, Coreano e Árabe. Leia cuidadosamente todas as instruções de operação antes de operar o projetor.

Before using the projector, please read this operation manual carefully.

Introduction

ENGLISH

There are two important reasons for prompt warranty registration of your new SHARP Projec tor, using the REGISTRATION CARD packed with the projector.

1. WARRANTY

This is to assure that you immediately receive the full beneﬁ t of the parts, service and labor warranty applicable to your purchase.

2. CONSUMER PRODUCT SAFETY ACT

To ensure that you will promptly receive any safety notiﬁ cation of inspection, modiﬁ cation, or recall that SHARP may be required to give under the 1972 Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT “LIMITED WARRANTY” CLAUSE.

WARNING:

High brightness light source. Do not stare into the beam of light, or view directly. Be especially careful that children do not stare directly into the beam of light.

To reduce the risk of ﬁ re or electric shock, do not

U.S.A. ONLY

expose this product to rain or mois ture.

See bottom of projector.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT REMOVE SCREWS

EXCEPT SPECIFIED USER

SERVICE SCREW.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.

DO NOT REMOVE COVER.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

The lightning ﬂ ash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product's enclosure that may be of sufﬁ cient magnitude to constitute a risk or electric shock to persons.

The exclamation point within a triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

WARNING:

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

WARNING:

The enclosed computer cable must be used with the device. The cable is provided to ensure that the device complies with FCC Class A veriﬁ cation.

FCC Regulations state that any unauthorized changes or modiﬁ cations to this equipment not expressly approved by the manufacturer could void the user's authority to operate this equip ment.

U.S.A. ONLY

INFORMATION

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the operation manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.

U.S.A. ONLY

PRODUCT DISPOSAL

This product utilizes tin-lead solder, and lamp containing a small amount of mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities, the Electronics Industries Alliance: www.eiae.org, the lamp recycling organization www.lamprecycle.org, or Sharp at 1-800-BE-SHARP.

U.S.A. ONLY

Caution Concerning Lamp Replacement

This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp

■

failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface scratches or deterioration of the lamp due to a lapse of usage time. The period of time up to failure largely varies depending on the individual lamp and/or the condition and the frequency of use. It is important to note that failure can often result in the bulb cracking. When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended

■

that the lamp be replaced with a new one immediately, even if the lamp appears to be operating normally. Should the lamp break, there is also a possibility that glass particles may spread inside of the

■

projector. In such a case, it is recommended you contact your nearest Sharp Authorized Projector Dealer or Service Center to assure safe operation. Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the

■

lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case of exposure to the gas, consult a doctor as soon as possible.

Caution

Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may

• cause burns or injury. Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to

• fully cool before removing the lamp unit. Do not touch the glass surface of the lamp unit or the inside of the projector.

• Do not loosen other screws except for the lamp unit cover and lamp unit.

• Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and

• continue to use the same lamp, this may cause the lamp to become damaged or explode.

Carefully change the lamp by following the instr uctions described on pages

■

* If you wish, you may have the lamp replaced at your nearest Sharp Authorized Projector

Dealer or Service Center.

* If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorized

Projector Dealer or Service Center for repair.

60 to 62.

How to Read this Operation Manual

The speciﬁ cations are slightly different, depending on the model. However, you can connect

■

and operate all models in the same manner.

In this operation manual, the illustration and the screen display are simpliﬁ ed for explanation, and

• may differ slightly from the actual display.

Using the Menu Screen

Select from the Quick Star t Menu, which is a collection of the most frequentl y used functions, or the Co mplete Menu, which enabl es advanced settings and adjustme nts.

Adjustment button s (P/R/O/Q)

ENTER button

MENU button

ENTER button

Buttons used in this operation

Button used in this step

On-screen display

Menu Selections (Quick St art Menu)

This operatio n can also be perform ed by using the buttons on the pro jector.•

Press MENU.

The “Quick Sta rt Menu” screen for the

• selected Input mode is displayed.

Press P or R to select t he

desired i tem, then pr ess ENTER.

Press P/R/O/Q to adjust the

item selec ted, then press ENTER.

Info

To display the advanced s ettings and

• adjustments, se lect “Go To Complete Menu”. Press ENTER to display the Complete Menu screen. If you do not want to display t he Quick Start

• Menu, set “Go To Complete Me nu” - “PRJ-ADJ2”

- “Quick Star t Menu” to “Off”. (See page

52.)

Input Search Start Resolution Resize

Keystone Eco+Quiet Language Information

SEL./ADJ. ENTER END

Adjustment buttons (P/R/O/Q)

RETURN button

Press RETURN to return

• to the previo us screen when the menu is displayed.

MENU button

Example

Quick Start Menu

Go To Complete Menu…

1024×768 Normal

Off English

Features

Useful

Introduction

.........Indicates safeguards for using the projector.

Info

Indicates additional information for setting up and operating the

.......

Note

projector.

For Future Reference

Maintenance

P. 57

Troubleshooting

PP. 65 and 66

Index

P. 70

Preparing

Introduction

How to Read this Operation Manual ......3

Contents .................................................4

IMPORTANT SAFEGUARDS ..................6

How to Access the PDF Operation

Manuals ..............................................10

Accessories ..........................................11

Part Names and Functions ...................12

Front View .............................................. 12

Top View ................................................ 12

Rear View (Terminals) .............................. 13

Inserting the Batteries ............................. 15

Usable Range ......................................... 15

Easy Start

Easy Start .............................................16

Setup and Projection .............................. 16

Setup

Setting Up the Projector .......................18

Setting Up the Projector ......................... 18

Standard Setup (Front Projection) ........... 18

Screen Size and Projection Distance ...... 19

Projection (PRJ) Mode ............................ 20

Ceiling-Mount Setup ............................... 20

Connections

Connecting the Projector to

Other Equipment ................................21

Controlling the Projector by

a Computer ........................................24

Connecting the Power Cord .................25

Using

Basic Operation

Turning the Projector On/Off ................26

Turning the Projector On ......................... 26

Turning the Power Off (Putting the

Projector into Standby Mode) .............. 26

Image Projection ..................................27

About the Setup Guide ........................... 27

Adjusting the Projected Image ................ 27

Correcting Trapezoidal Distortion ............ 29

Switching the Input Mode ....................... 30

Adjusting the Volume .............................. 30

Displaying the Black Screen and

Turning Off the Sound Temporarily ....... 30

Resize Mode .......................................... 31

Useful Features

Operating with the Remote Control......33

Displaying and Setting the

Break Timer ......................................... 33

Displaying the Pointer ............................. 33

Using the Spot Function ......................... 33

Switching the Eco+Quiet Mode .............. 33

Auto Sync (Auto Sync Adjustment) ......... 34

Freezing a Moving Image ........................ 34

Selecting the Picture Mode ..................... 34

Displaying an Enlarged Portion of

an Image ............................................. 34

Using the Remote Control as the

Wireless Computer Mouse ................... 35

Menu Items ...........................................36

Using the Menu Screen ........................39

Menu Selections (Quick Start Menu) .........39

Quick Start Menu .....................................40

Menu Selections (Complete Menu) ...........40

Picture Adjustment (“Picture” Menu) ....42

Selecting the Picture Mode ..................... 42

Adjusting the Image ................................ 43

Adjusting the Color Temperature ............. 43

Adjusting the Colors ............................... 43

Selecting the Film Mode ......................... 44

Reducing Image Noise (DNR) ................. 44

Eco+Quiet .............................................. 44

Signal Adjustment (“SIG-ADJ” Menu) ..45

Adjusting the Computer Image ............... 45

Resolution Setting .................................. 45

Signal Type Setting ................................. 45

Setting the Video System ....................... 46

Setting the Video Setup .......................... 46

Checking the Input Signal ....................... 46

Adjusting the Projected Image

(“SCR - ADJ” Menu) ...........................47

Setting the Resize Mode ......................... 47

Adjusting the Image Position .................. 47

Keystone Correction ............................... 47

Setting the Overscan .............................. 48

Setting the On-screen Display ................ 48

Closed Caption ...................................... 48

Selecting the Background Image ............ 49

Selecting the Setup Guide ...................... 49

Reversing/Inverting Projected Images ..... 49

Selecting the Wall Color .......................... 49

Selecting the On-screen Display Language

... 49

Adjusting the Projector Function

(“PRJ - ADJ1/2” Menu) ......................50

Auto Sync (Auto Sync Adjustment) ......... 50

Auto Power Off Function ........................ 50

Auto Restart Function ............................. 50

Speaker Setting ...................................... 50

Selecting the Transmission Speed

(RS-232C) ........................................... 50

Fan Mode Setting ................................... 51

System Lock Function ............................ 51

Keylock Function .................................... 52

Selecting the Quick Start Menu .............. 52

COMPUTER2 Select .............................. 52

Setting the FUNCTION Button Operation

STANDBY Mode ..................................... 53

DLP

LinkTM ............................................ 53

DLP

LinkTM Invert .................................. 53

Returning to the Default Settings ............ 53

Checking the Lamp Life Status ............... 53

Setting Up the Projector Network

Environment (“Network” Menu)..........54

Setting a Password ................................ 54

DHCP Client Setting ............................... 55

TCP/IP Setting ........................................ 55

Returning to Default Settings (Network) .. 55

Restart Network Function ....................... 55

Conﬁ rming the Projector Information ....... 56

Reference

Introduction

.. 53

Appendix

Maintenance .........................................57

Maintenance Indicators ........................58

Regarding the Lamp .............................60

Lamp ...................................................... 60

Caution Concerning the Lamp ................ 60

Replacing the Lamp ............................... 60

Removing and Installing the

Lamp Unit ............................................ 61

Resetting the Lamp Timer ...................... 62

Storing the Projector ............................63

How to Use the Storage Case ................ 63

Computer Compatibility Chart .............64

Troubleshooting ....................................65

For SHARP Assistance .........................67

Speciﬁ cations .......................................68

Dimensions ...........................................69

Index .....................................................70

IMPORTANT SAFEGUARDS

CAUTION: Please read all of these instructions before you operate this

product and save these instructions for later use.

Electrical energy can perform many useful functions. This product has been engineered and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the safeguards incorporated in this product, observe the following basic rules for its installation, use and servicing.

1. Read Instructions

All the safety and operating instructions should be read before the product is operated.

2. Retain Instructions

The safety and operating instructions should be retained for future reference.

3. Heed Warnings

All warnings on the product and in the operating instructions should be adhered to.

4. Follow Instructions

All operating and use instructions should be followed.

5. Cleaning

Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

6. Attachments

Do not use attachments not recommended by the product manufacturer as they may cause hazards.

7. Water and Moisture

Do not use this product near water–for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like.

8. Accessories

Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer's instructions, and should use a mounting accessory recom mended by the manufacturer.

9. Transportation

A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.

10. Ventilation

Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The open ings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This prod uct should not be placed in a built-in installation such as a book case or rack unless proper ventilation is provided or the manufacturer's in struc tions have been adhered to.

11. Power Sources

This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power com pany. For products intended to operate from battery power, or other sources, refer to the operating instructions.

12. Grounding or Polarization

This product is provided with one of the following types of plugs. If the plug should fail to ﬁ t into the power outlet, please contact your electrician. Do not defeat the safety purpose of the plug. a. Two-wire type (mains) plug. b. Three-wire grounding type (mains) plug

with a grounding terminal.

This plug will only ﬁ t into a grounding

type power outlet.

13. Power-Cord Protection

Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

14. Lightning

For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the cable system. This will pre vent damage to the product due to lightning and power-line surges.

15. Overloading

Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of ﬁ re or electric shock.

16. Object and Liquid Entry

Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a ﬁ re or electric shock. Never spill liquid of any kind on the product.

17. Servicing

Do not attempt to service this product yourself as opening or removing covers may expose you to dan ger ous voltage or other hazards. Refer all servicing to qualiﬁ ed service personnel.

18. Damage Requiring Service

Unplug this product from the wall outlet and refer servicing to qualiﬁ ed service person nel under the following conditions: a. When the power-supply cord or plug is

damaged.

b. If liquid has been spilled, or objects

have fallen into the product.

c. If the product has been exposed to rain

or water.

d. If the product does not operate normally

by following the operating instructions. Adjust only those con trols that are covered by the operating instructions, as an improper adjustment of other controls may result in damage and will often require extensive work by a qualiﬁ ed technician to restore the product to normal operation.

e. If the product has been dropped or

damaged in any way.

f. When the product exhibits a distinct

change in performance, this indicates a need for service.

19. Replacement Parts

When replacement parts are required, be sure the service technician has used replace ment parts speciﬁ ed by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in ﬁ re, electric shock, or other hazards.

20. Safety Check

Upon completion of any service or repairs to this product, ask the service technician to per form safety checks to determine that the product is in proper operating condition.

21. Wall or Ceiling Mounting

This product should be mounted to a wall or ceiling only as recommended by the manufacturer.

22. Heat

This product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including ampliﬁ ers) that produce heat.

Introduction

•

DLP® and the DLP logo are registered trademarks of Texas Instruments and BrilliantColor

•

Microsoft

and DLP® LinkTM are trademarks of Texas Instruments.

and Windows® are registered trademarks of Microsoft Corporation in the

United States and/or other countries.

•

PC/AT is a registered trademark of International Business Machines Corporation in the United States.

•

Adobe

Reader® is a trademark of Adobe Systems Incorporated.

Macintosh

is a registered trademark of Apple Computer, Inc. in the United States and/or

other countries.

•

PJLink is a registered trademark or an application trademark in Japan, the United States, Canada, E.U., China and/or other countries/regions.

•

All other company or product names are trademarks or registered trademarks of their respective companies. Some IC chips in this product include conﬁ dential and/or trade secret property belonging

• to Texas Instruments. Therefore you may not copy, modify, adapt, translate, distribute, reverse engineer, reverse assemble or discompile the contents thereof.

Observe the following safeguards when setting up your projector.

Caution concerning the lamp unit

■

Potential hazard of glass particles if lamp ruptures. In case of lamp rupture, contact your nearest Sharp Authorized Projector Dealer or Service Center for replacement. See “Regarding the Lamp” on page

60.

Caution concerning the setup of the projector

■

For minimal servicing and to maintain high image quality, SHARP recommends that this projector be installed in an area free from humidity, dust and cigarette smoke. When the projector is subjected to these environments, the vents and lens must be cleaned more often. As long as the projector is regularly cleaned, use in these environments will not reduce the overall operation life of the unit. Internal cleaning should only be performed by a Sharp Authorized Projector Dealer or Service Center.

Rest your eyes occasionally.

■

Continuously watching the screen for long hours will cause eye strain. Take regular breaks to rest your eyes.

Do not set up the projector in places exposed to direct sunlight or bright light.

■

Position the screen so that it is not in direct sunlight or room light. Light falling directly on the screen washes out the colors, making viewing difﬁ cult. Close the curtains and dim the lights when setting up the screen in a sunny or bright room.

Caution regarding placing of the projector

■

Place the projector on a level site within the adjustment range (9 degrees) of the adjustment foot.

■

After the projector is purchased, a faint smell from the vent may appear when the power is ﬁ rst turned on. This is normal and is not a malfunction. It will disappear after the projector is used for a while.

When using the projector in highaltitude areas such as mountains (at altitudes of approximately 1,500 meters (4,900 feet) or more)

When you use the projector in high-altitude

■

areas with thin air, set “Fan Mode” to “High”. Neglecting this can affect the longevity of the optical system. Use the projector at altitudes of 2,300

■

meters (7,500 feet) or less.

Warning about placing the projector in a high position

When placing the projector in a high

■

position, make cer tain it is carefully secure to avoid personal injury caused by the projector falling down.

Do not subject the projector to hard impact and/or vibration.

■

Protect the lens so as not to hit or damage the surface of the lens.

Avoid locations with extremes of temperature.

■

The operating temperature of the projector is from 41°F to 95°F (+5°C to +35°C).

■

The storage temperature of the projector is from –4°F to 140°F (–20°C to +60°C).

Do not block the exhaust and intake vents.

■

Allow at least 11 13/16 inches (30 cm) of space between the exhaust vent and the nearest wall or obstruction.

■

Ensure that the intake vent and the exhaust vent are not obstructed.

■

If the cooling fan becomes obstructed, a protection circuit will automatically put the projector into Standby mode to prevent overheat damage. This does not indicate a malfunction. (See pages 58 and 59.) Remove the projector power cord from the wall outlet and wait at least 10 minutes. Place the projector where the intake and exhaust vents are not blocked, plug the power cord back in and turn on the projector. This will return the projector to the normal operating condition.

Caution regarding usage of the projector

If you are not to use the projector for a long

■

time or before moving the projector, make certain you unplug the power cord from the wall outlet, and disconnect any other cables connected to it. Do not carry the projector by holding the

■

lens. When storing the projector, ensure that you

■

Using the projector in other countries

The power supply voltage and the shape of

■

the plug may vary depending on the region or country you are using the projector in. When using the projector overseas, make sure you use an appropriate power cord for the country you are in.

Temperature monitor function

close the lens shutter. Do not expose the projector to direct

■

sunlight or place next to heat sources. Doing so may affect the cabinet color or cause deformation of the plastic cover.

Other connected equipment

When connecting a computer or other

■

audio-visual equipment to the projector, make the connections AFTER unplugging the power cord of the projector from the AC outlet and turning off the equipment to be connected. Please read the operation manuals of the

■

projector and the equipment to be connected for instructions on how to make the connections.

■

If the temperature inside the projector increases, due to blockage of the air vents, or the setting location, the temperature warning indicator will blink. And if the temperature keeps on rising, “ ” will illuminate in the lower left corner of the picture with the temperature warning indicator blinking. If this state continues, the lamp will turn off, the cooling fan will run and then the projector will enter Standby mode. Refer to “Maintenance Indicators” on pages 58 and 59 for details.

Info

The cooling fan regulates the internal

• temperature, and its performance is automatically controlled. The sound of the fan may change during projector operation due to changes in the

fan speed. This does not indicate malfunction.

Closed Caption uses Bitstream Vera fonts

Permission is hereby granted, free of charge, to any person obtaining a copy of the fonts accompanying this license (“Fonts”) and associated documentation ﬁ les (the “Font Softwa re”), to reproduce and distribute the Font Software, including without limitation the rights to use, copy, merge, publish, distribute, and/or sell copies of the Font Sof tware, and to permit persons to whom the Font Sof tware is furnished to do so, subject to the following conditions:

The above copyright and trademark notices and this pe rmission notice shall be included in all copies of one or more of the Font Software typefaces.

The Font Software may be modiﬁ ed, altered, or adde d to, and in particular the de signs of glyphs or characters in the Fonts may be modiﬁ ed and additional glyphs or character s may be added to the Fonts, only if the fonts are renamed to names not containing either the words “Bitstream” or the word “Vera”.

This License becomes null and void to the extent applicable to Fonts or Font Software that has been modiﬁ ed and is distribute d under the “Bitstream Vera” names.

The Font Software may be sold as part of a larger software package but no copy of one or more of the Font Software typefaces may be sold by itself.

THE FONT SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARR ANT Y OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARR ANTIES OF MERCHANTABILIT Y, FITNESS FOR A PARTICUL AR PURPOSE AND NONINFRINGEMENT OF COPYRIGHT, PATENT, TRADEMARK, OR OTHER RIGHT. IN NO EVENT SHALL BITSTREAM OR THE GNOME FOUNDATION BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, INCLUDING ANY GENERAL, SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF THE USE OR INABILITY TO USE THE FONT SOFTWARE OR FROM OTHER DEALINGS IN THE FONT SOFTWARE.

Except as contained in this notice, the names of Gnome, the Gnome Foundation, and Bitstream Inc., shall not be use d in adver tising or other wise to promote the sale, use or other dealings in this Font Software without prior written authorization from the Gnome Foundation or Bitstream Inc., respectively. For further information, contact: fonts at gnome dot org.

Introduction

How to Access the PDF Operation Manuals

PDF operation manuals in several languages are included in the CD-ROM. To utilize these manuals, you need to install Adobe (Windows

Please download Adobe

or Macintosh®).

Reader® from the Internet (http://www.adobe.com).

Reader® on your computer

Accessing the PDF Manuals

For Windows®:

1 Insert the CD-ROM in the CD-ROM drive. 2 Double click the “My Computer” icon. 3 Double click the “CD-ROM” drive. 4 When you want to view the operation

manual

1) Double click the “MANUALS” folder.

2) Double click the language (name of the folder) that you want to view.

3) Double click the pdf ﬁ le to access the projector manuals.

When you want to view the SETUP

MANUAL

1) Double click the “SETUP” folder.

2) Double click the language (name of the folder) that you want to view.

3) Double click the pdf ﬁ le to access the SETUP MANUAL.

Note

If the desired pdf ﬁ le cannot be opened by double clicking the mouse, start Adobe® Reader® ﬁ r s t ,

• then specify the desired ﬁ le using the “File”, “Open” menu.

For Macintosh®:

1 Insert the CD-ROM in the CD-ROM drive. 2 Double click the “CD-ROM” icon. 3 When you want to view the operation

manual

1) Double click the “MANUALS” folder.

2) Double click the language (name of the folder) that you want to view.

3) Double click the pdf ﬁ le to access the projector manuals.

When you want to view the SETUP

MANUAL

1) Double click the “SETUP” folder.

2) Double click the language (name of the folder) that you want to view.

3) Double click the pdf ﬁ le to access the SETUP MANUAL.

SETUP MANUAL

Refer to the “SETUP MANUAL” contained on the supplied CD-ROM for details.

Connecting Pin Assignments ·······················································2 RS-232C Speciﬁ cations and Commands ····································· 4 Operating the Projector Using the PJLinkTM Protocol ·················· 10 Setting up the Projector Network Environment ·························· 11 Controlling the Projector via LAN ··············································· 17 Resetting the Lamp Timer of the Projector via LAN···················· 22 Troubleshooting ·········································································· 24

Accessories

Supplied accessories

Two R-6 batteries

(“AA” size, UM/SUM-3,

HP-7 or similar)

Remote control

DIN-D-s ub RS-232C ada ptor

(5 57/64" (15 cm))

Power cord*

(1) (2) (3) (4)

Introduction

RGB cable

(10' (3.0 m))

Storage case

For U.S. and

Canada, etc.

(6' (1.8 m))

* Which power cords are supplied along with your projector depends on the region. Use the power

cord that corresponds to the wall outlet in your country.

Operation manuals (this manual <TINS-E390WJZZ>, OPERATION MANUAL FOR STEREOSCOPIC

• 3D PROJECTION <TINS-E500WJZZ> and CD-ROM <UDSKAA121WJZZ>)

Note

Codes in “< >” are Replacement parts codes.•

For Europe, except U.K.

(6' (1.8 m))

For U.K. and

Singapore (6' (1.8 m))

For Australia, New

Zealand and Oceania

(6' (1.8 m))

Optional accessories

■ Lamp unit

■ Ceiling-mount adaptor

■ Ceiling-mount bracket

■ Ceiling-mount unit

■ Ceiling-mount extension tube

■ Remote receiver

■ 3 RCA to mini D-sub 15 pin cable (10n (3.0 m))

Note

Some of the optional accessories may not be available depending on the region. Please check with

• your nearest Sharp Authorized Projector Dealer or Service Center.

AN-D350LP AN-60KT AN-XRCM30 (for U.S.A. only) AN-TK201 <for AN-60KT> AN-TK202 <for AN-60KT> AN-EP101B <for AN-XRCM30> (for U.S.A. only) AN-MR2 AN-C3CP2

Part Names and Functions

Numbers in Z refer to the main pages in this operation manual where the topic is explained.

45 6

7 8

13 14

Front View

1 Exhaust vent 2 Zoom ring

For enlarging/reducing the picture.

3 Focus ring

For adjusting the focus.

4 Lens shutter 5 HEIGHT ADJUST lever 6 Adjustment foot 7 Remote control sensor 8 Speaker 9 Intake vent

26, 30

Top V i e w

10 Temperature warning indicator 11 Lamp indicator 12 Power indicator 13 STANDBY/ON button

For turning the power on and putting the

projector into Standby mode.

14 INPUT buttons (P/R)

For switching Input mode.

15 AUTO SYNC button

For automatically adjusting images when

connected to a computer.

16 Adjustment buttons (P/R/O/Q)

For selecting menu items.

17 ENTER button

For setting items selected or adjusted on

the menu.

18 MENU button

For displaying adjustment and setting

screens.

19 VOL ( Volume) buttons (–O/Q+)

For adjusting the speaker sound level.

123 4 5 6 7 8

Rear View (Terminals)

1 LAN terminal

Terminal for controlling the projector using a

computer via network.

2 RS-232C terminal

Terminal for controlling the projector using a

computer.

3 USB terminal

Terminal connecting with the USB terminal on the computer for using the supplied remote control as the computer mouse.

4 AUDIO OUT terminal

Audio output terminal of equipment connected to the audio input terminal.

5 MONITOR OUT* terminal

(Output terminal for computer RGB and component signals)

Terminal for connecting a monitor.

COMPUTER/COMPONENT 2* input

terminal

Terminal for computer RGB and component signals.

* You must switch the setting depending on

whether you are using the terminal for MONITOR OUT or COMPUTER/COMPONENT 2 input.

21, 22

131211

6 AUDIO 1 input terminal 7 COMPUTER/COMPONENT 1 input

terminal

Terminal for computer RGB and component signals.

8 S-VIDEO input terminal

Terminal for connecting video equipment with an S-video terminal.

9 VIDEO input terminal

Terminal for connecting video equipment.

10 AUDIO 2 input terminal 11 AC socket

Connect the supplied power cord.

21, 22

12 Kensington Security Standard

connector

13 Rear adjustment foot

14 Security bar

Using the Kensington Lock

This projector has a Kensington Security

• Standard connector for use with a Kensington MicroSaver Security System. Refer to the information that came with the system for instructions on how to use it to secure the projector.

Introduction

Part Names and Functions (Continued)

Numbers in Z refer to the main pages in this operation manual where the topic is explained.

35, 33

34, 50

35, 39

5 6

7 8

10 11 12

ON button

For turning the power on.

STANDBY button

For putting the projector into the Standby mode.

INPUT buttons ( / ) For switching Input mode.

BREAK TIMER button

For displaying the break time.

MAGNIFY buttons

For enlarging/reducing part of the image.

PAGE UP/PAGE DOWN buttons

Same as the [Page Up] and [Page Down] keys on a computer keyboard, when with the USB connection (using a USB cable or the optional remote receiver).

POINTER button

For displaying the pointer.

MOUSE/Adjustment buttons (P/R/O/Q)

For moving the computer cursor when with the

• USB connection (using a USB cable or the optional remote receiver). For selecting and adjusting menu items.

•

18 19

20 21 22

35, 39

L-CLICK/EFFECT button

For the Left click when with the USB

• connection (using a USB cable or the optional remote receiver). For changing the pointer or spot area.

•

KEYSTONE button

For entering the Keystone Correction mode.

AUTO SYNC button

For automatically adjusting images when connected to a computer.

FUNCTION button

For operating and executing a function assigned to “FUNCTION Button”.

ECO+QUIET but ton

For lowering the noise of the cooling fan and extending the lamp life.

FREEZE button

For freezing images.

AV MUTE button

For temporarily displaying a black screen and turning off the sound.

VOL +/– (Volume) buttons

For adjusting the speaker sound level.

SPOT button

For displaying the spotlight.

ENTER button

For setting items selected or adjusted on the menu.

R-CLICK/RETURN button

For the Right click when with the USB

• connection (using a USB cable or the optional remote receiver). For returning to the previous menu screen

• during menu operations.

MENU button

For displaying adjustment and setting screens.

RESIZE button

For switching the picture size (NORMAL, 16:9, etc.).

3D MODE button

See the OPERATION MANUAL FOR STEREOSCOPIC 3D PROJECTION provided separately.

PICTURE MODE button

For selecting the appropriate picture.

Inserting the Batteries

Pull down the tab on the cover and remove the

cover towards the direction of the arrow.

Insert the batteries.

Insert the batteries making sure the polarities correctly match

• the m and n marks inside the battery compartment.

Insert the lower tab of the cover into the opening,

and lower the cover until it clicks in place.

Incorrect use of the batteries may cause them to leak or explode. Please follow the precautions below

Caution

Danger of explosion if battery is incorrectly replaced.

• Replace only with alkaline or manganese batteries.

Insert the batteries making sure the polarities correctly match the m and n marks inside the battery

• compartment. Batteries of different types have different properties, therefore do not mix batteries of different types.

• Do not mix new and old batteries.

•

This may shorten the life of new batteries or may cause old batteries to leak.

Remove the batteries from the remote control once they have run out, as leaving them in can cause them to leak.

•

Battery ﬂ uid from leaked batteries is harmful to skin, therefore ensure you wipe them ﬁ rst and then remove them using a cloth.

The batteries included with this projector may run down in a short period, depending on how they are kept.

• Be sure to replace them as soon as possible with new batteries. Remove the batteries from the remote control if you will not be using the remote control for a long time.

• Comply with the rules (ordinance) of each local government when disposing of worn-out batteries.

•

Introduction

Usable Range

The remote control can be used to control the projector within the ranges shown in the illustration.

Note

•

The signal from the remote control can be reﬂ ected off a screen for easy operation. However, the effective distance of the signal may differ depending on the screen material.

When using the remote control

Ensure that you do not drop it or expose it to

• moisture or high temperature. The remote control may malfunction under a

• ﬂ uorescent lamp. In this case, move the projector away from the ﬂ uorescent lamp.

30°

Remote control

Remote control sensor

33n (10 m)

Remote control signal

Remote control signal transmitters

transmitters

Easy Start

This section shows the basic operation (projector connecting with the computer). For details, see the page described below for each step.

Setup and Projection

In this section, connection of the projector and the computer is explained using one example.

STANDBY/ON button

O/Q buttons

INPUT buttons

Zoom ring

Focus ring

HEIGHT

ADJUST lever

STANDBY button

ON button

INPUT buttons

Adjustment

buttons

(P/R/O/Q)

KEYSTONE button

1. Place the projector facing a wall or a screen

2. Connect the projector to the computer and plug the power cord into the AC socket of the projector

When connecting equipment other than a computer, see pages

22 and 23.

_PP. 21, 25

3. Open the lens shutter fully and then turn the projector on

On the projector On the remote control

_P. 2 6

P. 18

4. Adjust the projected image with the Setup Guide

1 After the projector turns on, the Setup Guide appears.

(When “Setup Guide” is set to “On”. See page

Follow the steps in the Setup Guide and adjust the focus, height (angle) and picture size.

49.)

3 After adjusting the focus, height (angle) and picture size, press ENTER to ﬁ nish the

Setup Guide.

_P. 2 7

5. Correct trapezoidal distortion

Correcting trapezoidal distortion using Keystone Correction.

On the remote control

Shrinks

upper side.

Shrinks

lower side.

_P. 2 9

6. Select the Input mode

Press INPUT P/R to display the INPUT list. Use INPUT P/R to select the Input mode, and use O /Q to select the audio input terminal.

On the

projector

INPUT list

INPUT Audio

1 COMPUTER1

On the

projector

Easy Start

On the remote

control

2 MONITOR OUT

S-VIDEO

VIDEO

On the remote

control

_P. 3 0

7. Turn the computer on

8. Turn the power off

Press STANDBY/ON on the projector or STANDBY on the remote control, and then press the button again while the conﬁ rmation message is displayed to put the projector into Standby mode.

On the

projector

On the remote

control

On-screen display

_P. 2 6

Setting Up the Projector

For optimal image quality, position the projector perpendicular to the screen with the projector's feet ﬂ at and level. Doing so will eliminate the need for Keystone correction and provide the best image quality. (See page 29.)

Standard Setup (Front Projection)

Place the projector at the required distance

■

from the screen according to the desired picture size. (See page 19.)

Indication of the Projection Image Size and Projection Distance

Example: 4:3 Signal Input (Normal Mode)

Picture Size

300" (762 cm)

200" (508 cm)

100" (254 cm)

40" (102 cm)

32"

24"

(81 cm

160"

(406 cm

80"

60"

(203 cm

61 cm)

5'6

"–

4'6

(1.4 m – 1.7 m)

240"×180"

(610 cm × 457 cm)

120"

305 cm)

152 cm)

13'9

"–

11'4

(3.5 m – 4.2 m)

22'8

27'6

"–

(6.9 m – 8.4 m)

34'0

(10.4 m –

–41'3"

Projection Distance

12.6 m)

Screen Size and Projection Distance

Screen

Lens center

4:3 Signal Input (Normal Mode)

Picture (Screen) size Projection distance [L]

Diagonal [χ]

300"(762 cm) 610 cm (240") 457 cm (180") 10.4 m (34' 0") 12.6 m (41' 3") 18 cm 250"(635 cm) 508 cm (200") 381 cm (150") 8.6 m (28' 4") 10.5 m (34' 4") 15 cm 200"(508 cm) 406 cm (160") 305 cm (120") 6.9 m (22' 8") 8.4 m (27' 6") 12 cm 150"(381 cm) 305 cm (120") 229 cm (90") 5.2 m (17' 0") 6.3 m (20' 7") 9 cm 120"(305 cm) 244 cm (96") 183 cm (72") 4.1 m (13' 7") 5.0 m (16' 6") 7 cm 100"(254 cm) 203 cm (80") 152 cm (60") 3.5 m (11' 4") 4.2 m (13' 9") 6 cm

80"(203 cm) 163 cm (64") 122 cm (48") 2.8 m (9' 1") 3.3 m (11' 0") 5 cm 70"(178 cm) 142 cm (56") 107 cm (42") 2.4 m (7' 11") 2.9 m (9' 7") 4 cm 60"(152 cm) 122 cm (48") 91 cm (36") 2.1 m (6' 10") 2.5 m (8' 3") 4 cm 40"(102 cm) 81 cm (32") 61 cm (24") 1.4 m (4' 6") 1.7 m (5' 6") 2 cm

Width Height Minimum [L1] Maximum [L2]

16:9 Signal Input (16:9 Mode)

Picture (Screen) size Projection distance [L]

Diagonal [χ]

300''(762 cm) 664 cm (261'') 374 cm (147'') 11.3 m (37' 1") 13.7 m (44' 11") 82 cm 250''(635 cm) 553 cm (218'') 311 cm (123'') 9.4 m (30' 11") 11.4 m (37' 5") 69 cm (27") ±52 cm 200''(508 cm) 443 cm (174'') 249 cm (98'') 7.5 m (24' 9") 9.1 m (29' 11") 55 cm

150''(381 cm) 332 cm (131'') 187 cm (74'') 5.6 m (18' 6") 6.8 m (22' 5") 41 cm 120''(305 cm) 266 cm (105'') 149 cm (59'') 4.5 m (14' 10") 5.5 m (18' 0") 33 cm 100''(254 cm) 221 cm (87'') 125 cm (49'') 3.8 m (12' 4") 4.6 m (15' 0") 27 cm

80''(203 cm) 177 cm (70'') 100 cm (39'') 3.0 m (9' 11") 3.6 m (12' 0") 22 cm 60''(152 cm) 133 cm (52'') 75 cm (29'') 2.3 m (7' 5") 2.7 m (9' 0") 16 cm 40''(102 cm) 89 cm (35'') 50 cm (20'') 1.5 m (4' 11") 1.8 m (6' 0") 11 cm

When using the projector with screen sizes not listed in the above charts, calculate the values according to the formulas.

L1: Minimum projection distance (m/ft) 0.03457χ0.03457χ / 0.3048 0.03766χ0.03766χ / 0.3048 L2: Maximum projection distance (m/ft) 0.04187 H:

Distance from the lens center to the bottom of the image (cm/in) Adjustable range of image position (cm/in) See page 47.

: Picture diagonal size : 40

Width Height Minimum [L1] Maximum [L2]

[m/cm] [Feet/inches] [m/cm] [Feet/inches]

0.06134χ0.06134χ / 2.54 0.27437χ0.27437χ / 2.54 — — ±0.20754χ±0.20754χ / 2.54

-300

4:3 Signal 16:9 Signal

0.04187χ / 0.3048 0.04562χ0.04562χ / 0.3048

Distance from the lens center to the bottom of the image [H]

(7 1/4") (6 1/32") (4 53/64") (3 5/8") (2 57/64") (2 27/64") (1 15/16") (1 11/16") (1 29/64") (31/32")

Distance from the lens center to the bottom of the image [H]

(32 13/32")

(21 39/64") (16 13/64") (12 31/32") (10 51/64") (8 41/64") (6 31/64") (4 21/64")

Adjustable range of

image position [S]

±62 cm

(±24 33/64")

(±20 ±42 cm ±31 cm ±25 cm ±21 cm ±17 cm ±12 cm

±8 cm

/64") (±16 11/32") (±12 1/4") (±9 13/16") (±8 11/64") (±6 17/32") (±4 29/32") (±3 17/64")

Setup

Note

Allow a margin of error in the values in the diagrams above.•

Setting Up the Projector (Continued)

Projection (PRJ) Mode

The projector can use any of the 4 projection modes shown in the diagram below. Select the mode most appropriate for the projection setting in use. (You can set the PRJ mode in “SCRADJ” menu. See page 49.)

Table mounted, front projection

■

[Menu item ➞ “Front”]

Table mounted, rear projection

■

(with a translucent screen) [Menu item ➞ “Rear”]

Ceiling mounted, front projection

■

[Menu item ➞ “Ceiling + Front”]

■

Ceiling mounted, rear projection (with a translucent screen) [Menu item ➞ “Ceiling + Rear”]

a

Ceiling-Mount Setup

It is recommended that you use the optional Sharp ceiling-mount adaptor and unit for this installation. Before mounting the projector, contact your nearest Sharp Authorized Projector Dealer or Service Center to obtain the recommended ceiling-mount adaptor and unit (sold separately).

Connecting the Projector to Other Equipment

Before connecting, ensure that the power cord of the projector is unplugged from the AC outlet and turn off the equipment to be connected. After making all connections, turn on the projector and then the other pieces of equipment. When connecting a computer, ensure that it is the last equipment to be turned on after all the connections are made.

For more details of connection and cables, refer to the operation manual of the connecting equipment.

• You may need other cables or connectors not listed below.

•

Terminals on the Projector

Equipment

Computer

Note

•

You can also use the COMPUTER/COMPONENT 2 terminal as the MONITOR OUT terminal. To use this terminal as an input terminal, set “COMPUTER2 Select” to “Input” before connecting the external equipment. (See page

•

See page projector. Use with computer signals other than those listed may cause some of the functions to not work.

•

A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest Macintosh Dealer.

•

Depending on the computer you are using, an image may not be projected unless the computer's external output port is switched on (e.g. Press “Fn” and “F5” keys simultaneously when using a SHARP notebook computer). Refer to the speciﬁ c instructions in

your computer's operation manual to enable your computer's external output port.

64 “Computer Compatibility Chart” for a list of computer signals compatible with the

Terminal on

connected equipment

RGB

output

terminal

52.)

Cable

RGB cable (supplied) COMPUTER/

Terminal o n the

projector

COMPONENT 1, 2

Connections

Connecting the Projector to Other Equipment (Continued)

Equipment

Video equipment

Camera/Video game

Terminal on

connected equipment

Component

video output

terminal

S-video

output

terminal

Video output

terminal

Component

video

output

terminal

S-video

output

terminal

Video

output

terminal

Cable

3 RCA to mini D-sub 15 pin cable (optional, AN-C3CP2)

S-video cable (commercially available) S-VIDEO

Video cable (co mmercially available) VIDEO

Cables for a camera or a video game/3 RCA to mini D-sub 15 pin cable (optional, AN-C3CP2)

RCA adaptor plug (commercially available)

Cables for a camera or a video game

Terminal o n the

projector

COMPUTER/ COMPONENT 1, 2

S-VIDEO

VIDEO

Note

•

When you connect video equipment with a 21-pin RGB output (Euro-scart) to the projector, use a

52.)

commercially available cable that ﬁ ts in the projector terminal you want to connect. The projector does not support RGBC signals via the Euro-scart.

•

Equipment

Audio equipment

Terminal on

connected equipment

ø3.5 mm

audio output

terminal

Cable

ø3.5 mm stereo or mono audio cable (commercially available or available as Sharp ser vice pa rt QCNWGA03 8WJPZ)

Terminal o n the

projector

AUDIO 1

RCA audio

output

terminal

Audio

output

terminal

Monitor RGB

Ampliﬁ er

input

terminal

ø3.5 mm

audio input

terminal

RCA audio

input

terminal

RCA audio cable (commercially available)

Cables for a camera or a video game

RGB cable (supplied or commer cially available)

ø3.5 mm stereo or mono audio cable (commercially available or available as Sharp ser vice pa rt QCNWGA03 8WJPZ)

ø3.5 mm stereo minijack to RCA audio cable (commercially available)

AUDIO 2

MONITOR OUT

AUDIO OUT

Note

•

You can also use the MONITOR OUT terminal as the COMPUTER/COMPONENT 2 terminal. To use this terminal as an output terminal, set “COMPUTER2 Select” to “Monitor Output” before connecting the external equipment. (See page When using the ø3.5 mm mono audio cable, the volume level will be half of when using the ø3.5 mm

•

52.)

stereo audio cable. You can select AUDIO 1 or AUDIO 2 in the INPUT list. (See page

• RGB signals and Component signals can be output to the monitor.

•

30.)

Connections

Controlling the Projector by a Computer

When the RS-232C terminal on the projector is connected to a computer with a DIN-D-sub RS232C adaptor (supplied) and an RS-232C serial control cable (cross type, commercially available), the computer can be used to control the projector and check the status of the projector. Refer to the “SETUP MANUAL” contained on the supplied CD-ROM for “RS-232C Speciﬁ cations and Commands”.

When connecting to a computer using a DIN-D-sub RS-232C adaptor (supplied) and an RS-232C serial control cable

To RS-232C terminal

DIN-D-sub RS-232C adaptor (supplied)

Computer

To R S-232C termi n al

RS-232C serial control cable (cross type, commercially available)

Note

•

The RS-232C function may not operate if your computer terminal is not correctly set up. Refer to the operation manual of the computer for details. Refer to pages 2 to 9 of the “SETUP MANUAL” contained on the supplied CD-ROM for “Connecting

• Pin Assignments” and “RS-232C Speciﬁ cations and Commands”.

Info

•

Do not connect the RS-232C cable to a port other than the RS-232C terminal on the computer. This may damage your computer or projector. Do not connect or disconnect an RS-232C serial control cable to or from the computer while it is on.

• This may damage your computer.

When connecting to the LAN terminal using a LAN cable

LINK LED (green) Illuminates when linked.

TX/RX LED (yellow) Illuminates when transmitting/receiving data.

* To ensure safety, do not connect the LAN terminal

with any cables that may cause excessive voltage such as a telephone line.

Hub

Computer

To L AN te r minal

LAN cable (Category 5 type, commercially available)

Note

•

When connecting to a hub, use a straight-through Category 5 (CAT.5) type cable (commercially available). When connecting to a computer, use a cross-over Category 5 (CAT.5) type cable (commercially

• available).

Connections

Connecting the Power Cord

Plug the supplied power cord into the AC socket on the rear of the projector. Then plug into AC outlet.

Power cord

Power cord (supplied)

(supplied)

AC socket

To AC ou t let

Turning the Projector On/Off

Info

Turning the Projector On

Note that the connections to external equipment and power outlet should be done before performing the operations written below. (See pages

Open the lens shutter fully and press STANDBY/ON on the projector or ON on the remote control.

•

The power indicator illuminates green.

•

After the lamp indicator illuminates, the projector is ready to start operation.

21 to 25.)

•

When “Auto Restart ” is set to “On”:

If the power cord is unplugged from the outlet or the breaker switch is turned off when the projector is on, then the projector automatically turns on when the power cord is plugged into the AC outlet or the breaker switch is turned on. (See page

•

English is the factory default language. If you want to change the on-screen display to another language, change the language according to the procedure on page

50.)

49.

Power indicator Lamp indicator

Note

About the Lamp Indicator

•

The lamp indicator illuminates to indicate the status of the lamp.

Green: The lamp is on. Blinking in green: The lamp is warming up. Red: The lamp is shut down

abnormally or the lamp should be replaced.

When switching on the projector, a slight

• ﬂ ickering of the image may be experienced within the ﬁ rst minute after the lamp has been illuminated. This is normal operation as the lamp's control circuitry is stabilising the lamp output characteristics. It should not be regarded as faulty operation. If the projector is put into Standby mode and

• immediately turned on again, the lamp may take some time to start projection. When System Lock is set, the keycode input

• box appears. To cancel the keycode setting, input the keycode that you have already set. See page

51 for details.

Turning the Power Off (Putting the Projector into Standby Mode)

Press STANDBY/ON on the projector or STANDBY on the remote control, then press that button again while the conﬁ rmation message is displayed, to put the projector into Standby mode.

•

The projector cannot be turned on while cooling.

STANDBY/ON button

STANDBY button

On-screen display (conﬁ rmation message)

ON button

Info

Direct Power O ff function:

•

You can unplug the power cord from the AC outlet even if the cooling fan is still running.

Image Projection

About the Setup Guide

After turning on the projector, the Setup Guide screen appears to assist you with projector setup.

Guidance items 1 FOCUS 2 HEIGHT ADJUST 3 ZOOM

Press ENTER to exit the Setup Guide screen.

Note

•

The Setup Guide screen automatically highlights the items in the following order:

1 FOCUS

2 HEIGHT ADJUST

Setup Guide screen

3 ZOOM4 ENTER

However, you can adjust the focus or height (angle) regardless of the highlighted item. If you do not want to display the Setup Guide

• for the next time, set “Menu” - “SCR - ADJ” “Setup Guide” to “Off”. (See page

49.)

Adjusting the Projected Image

1 Adjusting the Focus

You can adjust the focus with the focus ring on the projector.

Rotate the focus ring to adjust the focus while watching the projected image.

Using the knob on the focus ring will make the

• adjustments easier.

ENTER button

Operation

Basic

Focus ring

Image Projection (Continued)

2 Adjusting the Height

The height of the projector can be adjusted using the adjustment feet at the front and rear of the projector.

When the screen is above the projector, the projection image can be made higher by adjusting the projector.

Lift the projector to adjust its

height while lifting the HEIGHT ADJUST lever.

Remove your hands from the

HEIGHT ADJUST lever of the projector after its height has been ﬁ nely adjusted.

The angle of projection is adjustable up to

• 9 degrees from the surface on which the projector is placed.

Use the rear adjustment foot to

make the projector level.

The projector is adjustable ±2 degrees

• from the standard position.

Note

When adjusting the height of the projector,

• trapezoidal distortion occurs. Follow the procedures in Keystone Correction to correct the distortion. (See pages

29 and 47.)

Info

Do not apply too much pressure on the

• projector when the front adjustment foot comes out. When lowering the projector, be careful not to

• get your ﬁ ngers caught in the area between the adjustment foot and the projector. Hold the projector ﬁ rmly while lifting or carrying.

• Do not hold by the lens area.

•

Make small adjustments.

HEIGHT ADJUST lever

Rear adjustment footRear adjustment foot

3 Adjusting the Picture Size

You can adjust the picture size using the zoom ring on the projector.

Rotate the zoom ring to enlarge or shrink the picture size.

Using the knob on the zoom ring will make the

• adjustments easier.

Zoom ringZoom ring

Correcting Trapezoidal

Distortion

When the image is projected either from the top or from the bottom towards the screen at an angle, the image becomes distorted trapezoidally. The function for correcting trapezoidal distortion is called Keystone Correction.

Adjustment buttons (P/R/O/Q)

Note

•

The Keystone Correction can be adjusted up to an angle of approximately ±40 degrees and the screen can also be set up to an angle of approximately ±40 degrees.

Press KEYSTONE to enter the

Keystone Correction mode.

Press P/Q or O/R to adjust the

Keystone Correction.

Note

•

To return to the default setting, press RETURN while the on-screen display of the Keystone Correction mode is on the screen.

Press KEYSTONE.

The on-screen display of the Keystone

• Correction mode will disappear.

RETURN button

KEYSTONE button

On-screen display (Keystone Correction mode)

ADJUST END

Shrinks upper side. (Move the slide bar in the + direction.)

Shrinks lower side. (Move the slide bar in the - direction.)

0KEYSTONE

Info

•

While adjusting the image using Keystone Correction, straight lines and the edges of the image may appear jagged.

Operation

Basic

Image Projection (Continued)

Switching the Input Mode

Select the appropriate Input mode for the connected equipment.

Press INPUT

to display the INPUT list. Use INPUT

to select the Input

mode, and use O/Q to select the audio input terminal.

Adjusting the Volume

Press VOL +/– on the remote control or –O/Q+ on the projector to adjust the volume.

Note

Pressing VOL–/–O will lower the volume.

• Pressing VOL+/Q+ will raise the volume.

•

When the projector is connected to external equipment, the volume level of the external equipment changes in accordance with the volume level of the projector. Set the projector's volume to the lowest level when turning the projector on/off or when changing the input signal.

•

When you do not want to output the sound from the projector's speaker while the projector is connected to external equipment, set “Speaker” in the “PRJ-ADJ1” menu to “Off”. (See page

50.)

On-screen displayOn-screen display

INPUT buttons

AV MUTE button

VOL +/– (Volume)

VOL +/– (Volume) buttons

buttons

O/Q buttons

Displaying the Black Screen and Turning Off the Sound

Temporarily

Press AV MUTE on the remote control or close the lens shutter to temporarily display a black screen and turn off the sound.

Note

Pressing AV MUTE again will turn the

• projected image back on. When you close the lens shutter, the projector will

• be set to AV Mute mode and then the projector will be turned off automatically after about 30 minutes.

On-screen display

Resize Mode

This function allows you to modify or customize the Resize mode to enhance the input image. Depending on the input signal, you can choose a desired image.

Press RESIZE.

See page 47 for setting on menu screen.

•

COMPUTER

Main resolution NORMAL FULL NATIVE BORDER 16:9

SVGA (800 × 600)

4:3 aspect ratio

Other aspect ratios

Computer Image type NORMAL FULL NATIVE BORDER 16:9

Resolution lower than

XGA

Resolution

higher than

XGA

XGA (1024 × 768) —

SXGA (1152 × 864) 1152 × 864 UXGA (1600 × 1200) 1600 × 1200 SXGA (1280 × 1024) 968 × 768

1280 × 720 1024 × 576 1280 × 720 — — 1360 × 768 1024 × 578 1360 × 768 — — 1366 × 768 1024 × 576 1366 × 768 — — 1280 × 768 1024 × 614 1280 × 768 960 × 576 1280 × 800 1024 × 640 1280 × 800 922 × 576

Inpu t sign al For 4:3 s cree n For 16: 9 scre en

4:3 aspect ratio

1024 × 768 —

1024 × 768

—

800 × 600

768 × 576

1280 × 1024 720 × 576

—

RESIZE

RESIZE button

button

1024 × 576

Operation

Basic

SXGA (128 0 × 1024)

5:4 aspect ratio

1280 × 72 0

1360 × 76 8 1366 × 76 8

1280 × 76 8

1280 × 800

: Cutout area on which images cannot be projected

: Area where the signals are off screen *1 The Image Shift function can be used for these images. *2 Same as NORMAL mode

16:9 aspect ratio

16:10 aspect ratio

—

Image Projection (Continued)

VIDEO/DTV

Inpu t sign al For 4:3 s cree n For 16: 9 scre en

Video/DTV Image type NORMAL AREA ZOOM V-STRETCH BORDER 16:9

4:3 aspect ratio

I, 48 0P,

480 576

I, 576P,

NTSC, PAL,

SECAM

720P, 1035I,

1080

I, 1080P

540P

: Cutout area on which images cannot be projected

: Area on which the image is not included in the original signals *1 The Image Shift function can be used for these images. *2 Same as NORMAL mode.

Squeeze

Letter box

16:9 aspect ratio

(4:3 aspect ratio in 16:9)

*1 *1

—

About Copyrights

•

When using the Resize function to select an image size with a different aspect ratio to a TV program or video image, the image will look different from its original appearance. Keep this in mind while choosing an image size.

•

The use of the Resize or Keystone Correction function to compress or stretch the image for commercial purposes/public displays in a café, hotel, etc. may be an infringement of copyright protected by law for copyright holders. Please use caution.

Operating with the Remote Control

BREAK TIMER button

FREEZE button

MAGNIFY buttons

POINTER button

SPOT button

Adjustment buttons (P/R/O/Q)

EFFECT button PICTURE MODE button

ECO+QUIET button AUTO SYNC button

Displaying and Setting the Break Timer

Press BREAK TIMER.

The timer starts to count down from 5

• minutes.

On-screen display

Press P/R/O/Q to adjust the

length of the break time.

Increases with P or Q

•

5 minutes ➞ 6 minutes ➞ 60 minutes

Shortens with O or R

•

4 minutes ➞ 3 minutes ➞1 minute The break time can be set in units of one

• minute (up to 60 minutes).

Canceling the break timer display function

Press BREAK TIMER.

Note

•

The Break Timer is not available while the projector is operating the following functions.

- Auto Sync

- Freeze

- AV Mute

- Input Search

Displaying the Pointer

Press POINTER and press P/R/

O/Q on the remote control to move the pointer.

Press EFFECT to change the pointer icon

• (5 types).

Finger1 Finger2 Heart Underline

Star

Press POINTER again.

The pointer will disappear.

•

Using the Spot Function

Press SPOT and press P/R/O/Q

on the remote control to move the spot area.

Press EFFECT to change the spot area

• size (3 types).

1/9 1/25 1/8

Press SPOT again.

The spot area will disappear.

•

Switching the Eco+Quiet Mode

Press ECO+QUIET to switch the Eco+Quiet mode between on and off.

When the Eco+Quiet Mode is set to “ON”, the

• sound of the cooling fan will turn down, the power consumption will decrease, and the lamp life will extend.

Note

Refer to “Eco+Quiet” on page 44 for details.•

Features

Useful

Operating with the Remote Control (Continued)

Auto Sync (Auto Sync Adjustment)

Auto Sync function works when detecting input signal after the projector turns on.

Press AUTO SYNC to manually adjust with Auto Sync function.

Note

•

When the optimum image cannot be achieved with Auto Sync adjustment, use manual adjustments. (See page

45.)

Freezing a Moving Image

Press FREEZE.

The projected image is frozen.

•

Press FREEZE again to return to

the moving image from the currently connected device.

Displaying an Enlarged Portion of an Image

Graphs, tables and other portions of projected images can be enlarged. This is helpful when providing more detailed explanations.

Press MAGNIFY on the

remote control.

Enlarges the image.

• Pressing

• or reduces the projected image.

Note

Press

×1 ×2 ×3 ×4

Press

You can change the location of the

• enlarged image using P, R, O and Q.

Press RETURN on the remote

control to cancel the operation.

•

The magniﬁ cation then returns to ×1.

or MAGNIFY enlarges

Selecting the Picture Mode

You can select the appropriate Picture mode for the projected image, such as movie or video game.

Press PICTURE MODE.

•

When pressing PICTURE MODE, the Picture mode changes in the following order:

STANDARD PRESENTATION MOVIE GAME sRGB

Note

See page 42 for details on the Picture mode.•

* “sRGB” is displayed only when RGB signal is input.

Note

•

The selectable magniﬁ cations differ depending on the input signal.

•

In the following cases, the image will return to the normal size (×1).

- When switching the Input mode.

- When RETURN has been pressed.

- When the input signal is changed.

- When the input signal resolution and

refresh rate (vertical frequency) change.

- When the Resize mode is changed.

Using the Remote Control as the Wireless Computer Mouse

When connecting the projector and the computer with a USB cable, you can use the remote control as the computer mouse.

If the computer is placed too far away from the projector to be connected via the USB cable, the remote receiver (optional, AN-MR2) makes it possible to operate the projector with the remote control. For details, see the operation manual of the receiver.

Connecting with a USB cable

To USB terminal

USB cable (commercially available or available as Sharp service part QCNWGA014WJPZ)

The mouse pointer can be operated in the following way after it is connected.

When moving the cursor

■

Press MOUSE/Adjustment buttons (P/R/O/Q).

■

When left-clicking

Press L-CLICK.

When right-clicking

■

Press R-CLICK.

■

When your computer supports only a one-click mouse (such as Macintosh)

Press L-CLICK or R-CLICK. L-CLICK and R-CLICK have common function.

■

When using [Page Up] or [Page Down]

Same as the [Page Up] and [Page Down] keys on a computer keyboard. Press PAGE UP or PAGE D OWN.

To USB terminal

Computer

emote receiver

(optional, AN-MR2)

PAGE UP/

PAGE UP/ PAGE DOWN button

PAGE DOWN button

MOUSE/Adjustment

MOUSE/Adjustment buttons (//?/_)

buttons (//?/_)

R-CLICK button

L-CLICK button

Features

Useful

Note

This function only works with the Microsoft® Windows® OS and Mac OS® that support USB.

• You cannot use this function when displaying the menu screen.

• Conﬁ rm that the computer recognizes the USB connection.

•

Menu Items

The following shows the items that can be set in the projector.

“Quick Start Menu”

Main menu

Quick Start Menu

Input Search Start

Page 40

Resolution

Page 40

Resize

Page 40

Keystone

Page 40

[On/Off]

Eco + Quiet

Page 40

Language

Page 40

Information

Page 40

Go To Complete Menu

Page 40

“Picture” menu

Sub menu

Normal Full Native Area Zoom V-Stretch Border 16:9

+80-80

Main menu Sub menu

Picture

Picture Mode

Page 42 Page 42

Contrast

Bright

Color

Tint

Sharp

Red

Blue

Standard Presentation Movie Game sRGB*1

+30-30

Page 43

English Deutsch Español Nederlands Français Italiano Svenska Português

polski Magyar Türkçe

CLR Temp

Page 43

BrilliantColor™

1-1

Page 43

C.M.S. Setting [On/Off]

Page 43

C.M.S.

Page 43

Film Mode

Page 44

DNR Level 1

Page 44

[On/Off]

Eco+Quiet

Auto

Off

Level 2 Level 3

Page 44

Reset

C.M.S.-Hue

Page 43

C.M.S.-Saturation

Page 43

C.M.S.-Value

Page 43

Reset

Return

Reset

*1 Item when inputting RGB signal through

COMPUTER 1 or 2.

*2 Items when inputting component signal through

COMPUTER 1 or 2, or when selecting S-VIDEO or VIDEO.

+30-30

“Signal adjustment (SIG-ADJ)” menu

Main menu Sub menu

SIG-ADJ

Page 45

Clock

Phase

H-Pos

V-Pos

Reset

+150-150

+30-30

+150-150

+60-60

Page 45

Resolution

Page 45

Signal Type

Page 45

Video System Auto

Page 46

Video Setup

Page 46

Signal Info

Auto RGB YPbPr

PAL SECAM NTSC4.43 NTSC3.58 PAL -M PAL -N PAL-60

0 IRE

7.5 IRE

Page 46

*3 Items when inputting RGB signal through

COMPUTER/COMPONENT 1 or 2.

*4 Items when inputting COMPUTER/COMPONENT 1

or 2.

*5 Item when selecting COMPUTER/COMPONENT 1

or 2.

*6 Item when selecting S-VIDEO or VIDEO.

“Screen adjustment (SCR-ADJ)” menu

Main menu Sub menu

SCR - ADJ

Page 47

Resize

Page 47

Image Shift

Page 47

Keystone

Normal Full Native Area Zoom

+96-96

V-Stretch Border 16:9

+80-80

Page 47

Overscan [On/Off]

Page 48

OSD Display [On/Off]

Page 48

Closed Caption

Page 48

Background

Page 49

Setup Guide [On/Off]

Off CC1 CC2

Logo Blue None

Page 49

PRJ Mode

Page 49

Wall Color

Page 49

Language

Page 49

Front Ceiling + Front Rear Ceiling + Rear

Off Blackboard Whiteboard

English Deutsch Español Nederlands Français Italiano Svenska Português

polski Magyar Türkçe

Features

Useful

Menu Items

(Continued)

“Projector adjustment (PRJ-ADJ1/2)” menu

Main menu Sub menu

PRJ-ADJ1

Page 50

Auto Sync [On/Off]

Page 50

Auto Power Off [On/Off]

Page 50

Auto Restart [On/Off]

Page 50

Speaker [On/Off]

Page 50

RS-232C

Page 50

Fan Mode

Page 51

System Lock [Enable/Disable]

9600bps 38400bps 115200bps

Normal High

Page 51

Keylock [On/Off]

Page 52

Main menu Sub menu

PRJ-ADJ2

Page 50

Quick Start Menu [On/Off]

Page 52

COMPUTER2 Select

Page 52

FUNCTION Button

Page 53

STANDBY Mode

Page 53

DLP® LinkTM [On/Off]

Page 53

DLP

LinkTM Invert

Input Monitor Output

Input Search Audio Mute Image Shift Signal Info

Quick Start Eco

Page 53

All Reset

Page 53

Lamp Timer (Life)

Page 53

“Network” menu

Main menu

Network

Page 54

Password [Enable/Disable]

Page 54

DHCP Client

Page 55

TCP/IP

Page 55

Reset Network Setting

Page 55

Restart Network

Page 55

IP Address

Page 56

MAC Address

Page 56

Projector

Page 56

Link

Page 56

[On/Off]

Using the Menu Screen

Select from the Quick Start Menu, which is a collection of the most frequently used functions, or the Complete Menu, which enables advanced settings and adjustments.

Adjustment buttons (P/R/O/Q)

ENTER button

MENU button

ENTER button

Adjustment buttons (P/R/O/Q)

RETURN button

Press RETURN to return

• to the previous screen when the menu is displayed.

MENU button

Menu Selections (Quick Start Menu)

This operation can also be performed by using the buttons on the projector.•

Press MENU.

The “Quick Start Menu” screen for the

• selected Input mode is displayed.

Input Search Start

Press P or R to select the

desired item, then press ENTER.

Press P/R/O/Q to adjust the

item selected, then press ENTER.

Info

To display the advanced settings and

• adjustments, select “Go To Complete Menu”. Press ENTER to display the Complete Menu screen.

•

If you do not want to display the Quick Start Menu, set “Go To Complete Menu” - “PRJ-ADJ2”

- “Quick Start Menu” to “Off”. (See page

52.)

Resolution Resize

Keystone Eco+Quiet Language Information

SEL./ADJ. ENTER END

Example

Quick Start Menu

1024×768 Normal

Off English

Go To Complete Menu…

Features

Useful

Using the Menu Screen

(Continued)

Quick Start Menu

The following items can be conﬁ gured on the Quick Start Menu.

Selectable items Description

Input Search Start Automatically searches for and switches to the appropriate Input mode.

Resolution Manually change the resolution.

Resize Changes the Resize mode.

Keystone Corrects the keystone distortion of projected images.

Eco+Quiet When set to “On”, this function reduces the cooling fan noise and power

Language Selects the language displayed on the screen. (See page 49.) Information Displays the input signal, lamp use time, remaining lamp life, etc. Go To Complete Menu Displays the Complete Menu for advanced settings and adjustments.

Note

•

The setting of Resize mode will be made independently for each Input mode.

•

The setting of Eco+Quiet mode will be made independently for each Input mode and each Picture mode.

Pressing an operation button during input searching cancels the search.

Use this function when the image and screen size do not match with the resolution selected automatically. (See page

Use this function to stretch the image vertically or horizontally or when the edges of the image cannot be seen. (See page

Use this function to correct the trapezoidal distortion of images caused when projecting images at an angle to the screen. (See page

consumption, thereby prolonging the operating life of the lamp. (See page

45.)

47.)

44.)

Menu Selections (Complete Menu)

Example: Adjusting “Bright”.

This operation can also be performed by using the buttons on the projector.•

Press MENU.

The “Quick Start Menu” screen is

• displayed.

Press P or R to select “Go To

Complete Menu”.

Press Q or O and select

“Picture” to adjust.

Info

•

When “PRJ-ADJ2” - “Quick Start Menu” is set to “On”, pressing MENU displays the Quick Start Menu screen.

Example: “Picture” screen menu for COMPUTER (RGB) input

Menu item

SIG SCR PRJ1 PRJ2 Net.Picture

Picture Mode

Contrast 0 Bright Red Blue CLR Temp BrilliantColor C.M.S. Setting C.M.S. DNR Eco+Quiet Reset

SEL./ADJ. ENTER END

Standard

0 0

0 0 0 1

Level 2

Off

Press P or R and select “Bright”

to adjust.

•

The selected item is highlighted.

To adjust the projected image while watching it

Press ENTER.

•

The selected item (e.g. “Bright”) is displayed by itself at the bottom of the screen. When pressing P or R, the following item

• (“Red” after “Bright”) will be displayed.

Note

Press ENTER again to return to the

• previous screen.

Picture Net.

Picture Mode

Red

Red Blue

Blue

Items to be adjusted

Pict. SCR-ADJ Net.

Resize

Resize Image Shift 0

Image Shift 0 Keystone

Keystone

The item displayed by itself

SIG SCR PRJ1 PRJ2Picture

Standard

Contrast 0

Bright 0

CLR Temp

CLR Temp BrilliantColor

BrilliantColor C.M.S. Setting

C.M.S. Setting C.M.S.

C.M.S.

DNR

DNR Eco+Quiet

Eco+Quiet Reset

Reset

SEL./ADJ. Single ADJ END

SEL./ADJ. END

Picture

SEL./ADJ. Rtn. Menu END

SIG

Standard

0 0

0 1

Level 2

Level 2 Off

Off

PRJ1 PRJ2

Normal

Press ENTER.

0Bright

Picture SIG SCR PRJ1 PRJ2 Net.

Press O or Q to adjust the item

selected.

•

The adjustment is stored.

Press MENU.

•

The menu screen will disappear.

Picture SIG SCR PRJ1 PRJ2 Net.

Picture Mode

Contrast 0

Red

Red Blue

Blue CLR Temp

CLR Temp BrilliantColor

BrilliantColor C.M.S. Setting

C.M.S. Setting C.M.S.

C.M.S.

DNR

DNR Eco+Quiet

Eco+Quiet Reset

Reset

SEL./ADJ. Single ADJ END

Note

The MENU button is not available while the projector is operating:

•

- Auto Sync/Break Timer/Freeze/AV Mute/Input Search

Standard

15Bright

0 0

0 1

Level 2

Level 2 Off

Off

Features

Useful

Picture Adjustment (“Picture” Menu)

Menu operation n Page 40

Q PAGE1 Q PAGE2

Picture SIG SCR PRJ1 PRJ2 Net.

Picture Mode

Contrast 0 Bright Color Tint

Red Blue

0 0 0 0Sharp 0 0

Standard

Picture SIG SCR PRJ1 PRJ2 Net.

Picture Mode

CLR Temp

3 2

4 5

6 7

BrilliantColor C.M.S. Setting C.M.S. Film Mode DNR Eco+Quiet

Reset

Standard

0 1

Auto Level 2 Off

SEL./ADJ. ENTER END

Selecting the Picture Mode

Selectable

items

Description

The default settings of each item when selecting Picture Mode

CLR Temp BrilliantColor

SEL./ADJ. ENTER END

Eco+Quiet Standard For standard image 0 1 Off Presentation Brightens portions of image for

02Off

Adjusting the Image

Adjustment

items

Contrast For less

Bright For less

Color*

Tint*

Sharp*

Red*

Blue*

BrilliantColor™*2 *3For making the

*1 Not displayed in the RGB input mode. *2 Not adjustable/selectable when selecting “sRGB”. *3 BrilliantColor™ uses Texas Instruments'

BrilliantColor™ technology. As the BrilliantColor™ level is increased, the image becomes brighter while the color reproduction is kept at a high level.

O button Q button

contrast.

brightness. For less color

intensity. For making skin

tones purplish. For less

sharpness. For weaker red. For stronger

For weaker blue.

effect weaker.

For more contrast.

For more brightness.

For more color intensity.

For making skin tones greenish.

For more sharpness.

red. For stronger

blue. For making the

effect stronger.

Note

•

“Red”, “Blue”, “BrilliantColorTM” and “CLR Temp” cannot be set when “sRGB” is selected. To reset all adjustment items, select “Reset”

• and press ENTER.

Adjusting the Color

Temperature

Selectable

items

For lower color temperature for warmer, reddish incandescent-like

–1

images.

For higher color temperature for cooler, bluish, ﬂ uorescent-like images.

Note

Values on “CLR Temp” are only for general

• standard purposes.

Description

Adjusting the Colors

This function adjusts each of the six main colors that comprise the color wheel, altering their “Hue”, “Saturation”, or “Value”.

Selectable items Description

C.M.S.-Hue Sets the hue of the main colors. C.M.S.-Saturation Sets the saturation of the main

C.M.S.-Value Sets the brightness of the main

Reset The adjustments of “Hue”,

Return Returns to the “Picture” menu

colors

colors.

“Saturation” and “Value” of all colors are reset to the default setting.

screen.

Adjusting “Hue”, “Saturation”, or “Value”.

1 Select “On” for “C.M.S. Setting” in the “Picture”

menu and then press ENTER.

2 Select “C.M.S.” in the “Picture” menu and then

press ENTER.

3 Press P or R to select either “Hue”, “Saturation”, or

“Value” and then press ENTER.

4 Select the color to be adjusted with P or R and

adjust it with O or Q.

Example of adjusting the “Hue”

Main colors O button Q button

R (Red) Y (Yellow) Closer to red Closer to green G (Green) Closer to yellow Closer to cyan C (Cyan) Closer to green Closer to blue B (Blue) Closer to cyan M (Magenta) Closer to blue Closer to red

When “Saturation” is selected, the selected

•

Closer to magenta

color becomes O: lighter. Q: thicker. When “Value” is selected, the selected color

• becomes O: darker. Q: brighter. To reset the adjustment values of each color to

• the default settings, select “Reset” and press ENTER.

Closer to yellow

Closer to magenta

Features

Useful

Picture Adjustment (“Picture” Menu) (Continued)

Menu operation n Page 40

Selecting the Film Mode

This function provides high-quality playback of images originally projected at 24 fps, such as movies on DVDs.

Selectable

items

Auto Films are detected automatically. Off Films are not detected.

Note

•

This function is available for the following signals. With COMPUTER/COMPONENT 1 or 2 input:

- 480I

- 576I

- 1035I

- 1080I With S-VIDEO or VIDEO input:

- All signals

Reducing Image Noise (DNR)

Video digital noise reduction (DNR) provides high quality images with minimal dot crawl and cross color noise.

Selectable

items

Level 1 Level 2 Level 3

Sets the DNR level for viewing a clearer picture.

Description

Eco+Quiet

Selectable

items

Off 100%

Note

•

When “Eco+Quiet” is set to “On”, the fan sound and power consumption are lower than they are when “Off” is selected. (Projection brightness decreases as shown in the chart.)

Brightness and Power consumption

PG-D3510X PG-D3010X

PG-D2710X Approx. 75%

Approx. 65%

Note

This function is not available for some signals.•

Signal Adjustment (“SIG-ADJ” Menu)

Menu operation n Page 40

Pict. SIG-ADJ SCR PRJ1 PRJ2 Net.

Clock Phase

H-Pos V-Pos

Reset

Resolution

Signal Type

Video System

Video Setup

5 6

Adjusting the Computer Image

Signal Info 1024 x 768

H 48.3 kHz / V 60.0 Hz

SEL./ADJ. ENTER END

If the optimum image cannot be obtained with Auto Sync adjustment, use the SIG-ADJ function.

Selectable

items

Clock Adjusts vertical noise. Phase Adjusts horizontal noise (similar to

tracking on your VCR).

H-Pos Centers the on-screen image by

moving it to the left or right.

V-Pos Centers the on-screen image by

moving it up or down.

Description

Note

•

To reset all adjustment items, select “Reset” and press ENTER. The adjustable range of “H-Pos” (H-Position)

• and “V-Pos” (V-Position) may vary depending on the screen resolution of the computer.

0 0 0 0

1024 x 768 Auto

Auto 0 IRE

Signal Type Setting

This function allows you to select the input signal type RGB or Component for COMPUTER/ COMPONENT 1 or 2.

Selectable

items

Auto Input signals are automatically

recognized as RGB or component. RGB Set when RGB signals are received. YPbPr Set when Component signals are

received.

Description

Resolution Setting

Ordinarily, the type of input signal is detected and the correct Resolution mode is automatically selected. However, for some signals, the optimal Resolution mode in “Resolution” may need to be selected to match the computer display mode.

Note

•

See “Checking the Input Signal” on page 46 for information on the currently selected input signal.

Features

Useful

Signal Adjustment (“SIG-ADJ” Menu) (Continued)

Menu operation n Page 40

Setting the Video System

The video input system mode is factory preset to “Auto”; however, a clear picture from the connected audio-visual equipment may not be received, depending on the Video signal difference. In that case, switch the Video signal.

Selectable items

Auto PAL SECAM *NTSC4.43 NTSC3.58 PAL-M PAL-N PAL -60

* When reproducing NTSC signals in PAL

video equipment.

Note

•

The Video signal can only be set in S-VIDEO or VIDEO mode.

•

When “Video System” is set to “Auto”, you may not receive a clear picture due to signal differences. Should this occur, switch to the video system of the source signal.

Checking the Input Signal

This function allows you to check the current input signal information.

Setting the Video Setup

Selectable

items

0 IRE Sets the black level to 0 IRE.

7.5 IRE Sets the black level to 7.5 IRE.

Note

•

This function is available for the following signals. With COMPUTER/COMPONENT 1 or 2 input:

- 480I With S-VIDEO or VIDEO input:

- NTSC3.58

Description

Adjusting the Projected Image (“SCR-ADJ” Menu)

Menu operation n Page 40

31.)

SCR-ADJ

Normal

On On Off Logo On Front

Off English

Keystone Correction

Select “Keystone” on the “SCR-ADJ” menu and adjust with the slide bar.

See page 29 for details of Keystone Correction.

O buttonQ button

Pict. PRJ1 PRJ2 Net.SIG

Resize

Image Shift 0

Keystone

3 4

Overscan

OSD Display

Closed Caption

Background Setup Guide

PRJ Mode

Wall Color

Language

SEL./ADJ. ENTER END

Setting the Resize Mode

Use this function to stretch the image vertically or horizontally or when the edges of the image cannot be seen.

Note

For details of the Resize mode, see pages

•

31 and 32.

You can also press RESIZE on the remote

• control to set the Resize mode. (See page

Adjusting the Image

Position

You can move the projected image vertically.

Q buttonO button

Note

This function only works in some Resize

• modes. (See pages

31 and 32.)

Note

•

The Keystone Correction can be adjusted up to an angle of approximately ±40 degrees. You can also press KEYSTONE on the

• remote control to adjust Keystone Correction.

Features

Useful

Adjusting the Projected Image (“SCR-ADJ” Menu) (Continued)

Menu operation n Page 40

Setting the Overscan

This function allows you to set the overscan area (display area).

Selectable

items

On The input area is displayed without the

Off The whole input area is displayed.

•

This function is available for the following signals. With COMPUTER/COMPONENT 1 or 2 input:

- 480P

- 540P

- 576P

- 720P

- 1035I

- 1080I/1080P If noise appears at the screen edges when

• “Off” is selected, set the function to “On”. Also see “About Copyrights” on page

•

screen edges.

Note

Setting the On-screen

Description

32.

Display

Selectable

items

On All on-screen displays are displayed. Off VOLUME/AV MUTE/FREEZE/AUTO

SYNC/RESIZE/PICTURE MODE/ ECO+QUIET/MAGNIFY/Input Search/ Audio Mute/“An invalid button has been pressed.” are not displayed.

Description

Closed Caption

Info

This function is available for NTSC3.58 signal.

• This function does not work when the Resize

• mode is set to “Border”.

•

This function is available in the following cases only:

Resize mode Keystone Correction

Normal Area Zoom V-Stretch

16:9 -12 − +12

“Closed Caption” is a system which allows

• conversations, narration, and sound effects in TV programs (Limited regions) and home videos to be viewed as captions on the screen. Not all programs and videos will offer closed

• captioning. Please look for the symbol to ensure that captions will be shown. Two channels are available: CC1 and CC2.

•

Selectable

items

Off — CC1 Closed Caption mode for CH1 data CC2 Closed Caption mode for CH2 data

Note

Closed Caption may malfunction (white blocks,

• strange characters, etc.) if signal conditions are poor or if there are problems at the broadcast source. This does not necessarily indicate a problem with the projector. If any button is pressed to call up the on-

• screen display while viewing a Closed Caption broadcast, the closed captions will disappear.

-40 − +40

Description

Selecting the Background

Image

Selectable items Description

Logo Sharp logo screen Blue Blue screen None —

Selecting the Setup Guide

Selectable items Description

On Displaying the Setup Guide

Off Not displaying the Setup Guide.

when turning the projector on.

Menu operation n Page 40

Selecting the Wall Color

This function allows you to project the image to a colored (white or dark green) surface or wall without using a screen.

Selectable items Description

Off The Wall Color function is not

Blackboard Projects images onto a

Whiteboard Projects images onto a

Selecting the On-screen

activated.

blackboard (dark green).

whiteboard.

Display Language

Reversing/Inverting

Projected Images

Selectable items Description

Front Normal image (Projected from

Ceiling + Front Inverted image (Projected from

Rear Reversed image (Projected from

Ceiling + Rear Reversed and inverted image

See page

20 for details of Projection (PRJ) Mode.

the front of the screen)

the front of the screen with an inverted projector)

the rear of the screen or with a mirror)

(Projected with a mirror)

The projector can switch the on-screen display language among 17 languages.

English Deutsch Español Nederlands Français Italiano Svenska Português

polski Magyar Türkçe

Features

Useful

Adjusting the Projector Function (“PRJ-ADJ1/2” Menu)

Q PRJ-ADJ1

Pict. SCR PRJ-ADJ1SIG PRJ2 Net.

Auto Sync On

Auto Power Off On

Auto Restart On Speaker On

RS-232C

5 6

Fan Mode Normal System Lock

7 8

SEL./ADJ. ENTER END

Auto Sync (Auto Sync

9600bps

Disable OffKeylock

Adjustment)

Selectable

items

On Auto Sync adjustment will occur when

Off Auto Sync adjustment is not

the projector is turned on or when the input signals are switched, when connected to a computer.

automatically performed.

Note

•

Auto Sync adjustment is also performed by pressing AUTO SYNC.

•

The Auto Sync adjustment may take some time to complete, depending on the image of the computer connected to the projector.

•

When the optimum image cannot be achieved with Auto Sync adjustment, use manual adjustments. (See page

Auto Power Off Function

Selectable

items

On When no input signal is detected for

Off The Auto Power Off function will be

more than 15 minutes, the projector will automatically enter Standby mode.

disabled.

Note

When the Auto Power Off function is set to

• “On”, 5 minutes before the projector enters Standby mode, the message “Enter STANDBY mode in X min.” will appear on the screen to indicate the remaining minutes.

Description

45.)

Description

Q PRJ-ADJ2

Menu operation n Page 40

Pict. SCR PRJ-ADJ2SIG Net.

Quick Start Menu On

COMPUTER2 Select FUNCTION Button Input Search STANDBY Mode Quick Start

DLP

Link

DLP

Link TM Invert

All Reset

SEL./ADJ. ENTER END

Auto Restart Function

Selectable

items

Off The projector does not turn on

Selectable

items

On The audio signal is output from the

Off The audio signal is not output from the

automatically when the power cord is plugged into the AC outlet or the breaker switch is turned on.

Speaker Setting

internal speaker.

Selecting the Transmission

Speed (RS-

PRJ1

Monitor Output

Off

0 min0Lamp Timer(Life) 100%

Description

232C)

Make sure that both the projector and computer are set for the same baud rate.

Selectable

items

9600bps

38400bps

115 20 0b p s

Transmission speed is slow.

Transmission speed is rapid.

Description

Fan Mode Setting

This function changes the fan rotation speed.

Selectable

items

Normal Suitable for normal environments. High Set when using the projector at

altitudes of approximately 1,500 meters (4,900 feet) or more.

When “Fan Mode” is set to “High”, the fan rotation speeds up, and the fan noise becomes louder.

Description

Menu operation n Page 40

Note

If you input a wrong keycode, the cursor returns to

• the ﬁ rst point of the “Old Code”. The preset keycode is 4 R buttons on the

• projector. When you press the R button four times, the keycord input screen disappears.

Press the 4 buttons on the remote

control or on the projector to enter the new keycode in “New Code”.

System Lock Function

This function prevents unauthorized use of the projector. Once this function is activated, users must enter the correct keycode each time the projector is turned on. We suggest

you record the keycode in a safe place where only authorized users have access.

Info

If you lose or forget your keycode, contact

• your nearest Sharp Authorized Projector Dealer or Service Center (see page if the product warranty is valid, the keycode reset will incur a charge.

a

Setting/Changing the Keycode

Select “System Lock”, then press

ENTER or Q.

Select “Next”, then press ENTER.

The screen for entering the keycode

• appears.

Press the 4 buttons on the remote

control or on the projector to enter

67). Even

the preset keycode in “Old Code”.

•

When setting the keycode for the ﬁ rst time, press R on the projector for four times.

Setting the System Lock

Old Code

New Code Reconﬁrm

PRJ - ADJ1

––––

–––– ––––

Note

You cannot use the following buttons

• for keycode: STANDBY/ON, ON,

STANDBY, ENTER, L-CLICK, RCLICK/RETURN and MENU System Lock function recognizes

• each button on the remote control or on the projector as an individual button, even if they share the same button name. If you used the buttons on the projector in setting your keycode, the keycode cannot be canceled with the remote control.

Setting the System Lock

Old Code

New Code

Reconﬁrm

Enter the same keycode in “Re-

conﬁ rm”.

Note

To cancel the keycode that you have already set

Press R on the projector for four times in

• steps 4 and 5 above.

When the System Lock is set

When System Lock is set, the keycode input

• screen appears after the power is turned on. When it appears, enter the right keycode to start projection.

Input screen for keycode

System Lock

PRJ - ADJ1

****

– ––– ––––

––––

Features

Useful

Adjusting the Projector Function (“PRJ-ADJ1/2” Menu) (Continued)

Menu operation n Page 40

Keylock Function

Use this function to lock the operation buttons on the projector. This function can be set using either the menu screen or ENTER on the projector.

a

Setting with the menu screen

Taking the Keylock Of f

Hold down ENTER on the projector for about 5 seconds.

On-screen display

Selectable

items

On All buttons on the projector, except

Off Turns of f the Keylock function.

a

Setting with the projector buttons

STANDBY/ON, are locked.

Description

Locking the Operation Buttons

Hold down ENTER on the

projector for about 5 seconds while the projector is being turned on.

•

The Keylock function screen is displayed.

Use this function to lock the operation buttons on the projector. (Except STANDBY/ON button)

Note: You can release the keylock by holding down ENTER on the projector for about 5 seconds.

Return

SEL. ENTER END

Select “On”, then press

On-screen display

•

The Keylock function does not affect the operation with the remote control buttons. You cannot use the Keylock function while the

• projector is warming up.

PRJ - ADJ1

ENTER

Info

•

Even when Keylock function is set to “On”, STANDBY/ON on the projector can be used to turn on and off the power.

•

Keylock cannot be set while the projector is: displaying the “Setup Guide” or “Menu” screens, in Standby mode, warming up, changing input signals, operating the Auto Sync or Input Search function, in Freeze mode or on the “System Lock” screen during warming up.

Selecting the Quick

Start Menu

Selectable items Description

On Pressing MENU displays the

Off Pressing MENU displays the

COMPUTER2 Select

You can also use the MONITOR OUT terminal

as the COMPUTER/COMPONENT 2 terminal. Select whether to use the terminal as an input terminal or output terminal.

Selectable items Description

Input The terminal can be used as an

Monitor Output

Quick Start Menu screen.

Complete Menu screen.

input terminal (COMPUTER/ COMPONENT 2).

The terminal can be used as an output terminal (MONITOR OUT).

Note

•

Set this before connecting the external equipment. The setting cannot be changed when Input

• mode is “COMPUTER 2”.

Menu operation n Page

Setting the FUNCTION

Button Operation

You can assign one of the following functions to the FUNCTION button on the remote control. The assigned function can be performed by just pressing FUNCTION.

Selectable items Description

Input Search Automatically searches for and

Audio Mute For temporarily turning off the

Image Shift For moving the projected image

Signal Info Input signal information is

STANDBY Mode

When set to “Eco”, power consumption is reduced in Standby mode.

Selectable

items

Eco The monitor output, RS-232C and

Quick Start The monitor output, RS-232C and

switches to the appropriate Input mode.

sound. Press FUNCTION again to turn on the sound

vertically. (See page

displayed.

Description

Network functions are switched off in Standby mode.

Network functions are activated even if the projector is in Standby mode.

47.)

Returning to the Default

Settings

This function allows you to initialize the settings you have made in the projector.

Note

•

The following items or menu cannot be initialized.

- Resolution

- Language

- Lamp Timer (Life)

- System Lock

- COMPUTER2 Select

Checking the Lamp

Life Status

You c an c o nﬁ rm the cumulative lamp usage time and the remaining lamp life (percentage).

Lamp usage condition Remaining lamp life

“Life” 100% 5%

Operated exclusively with “Eco+Quiet” set to “On”

Operated exclusively with “Eco+Quiet” set to “Off”

Approx. 4,000 hours

Approx. 2,000 hours

Approx. 200 hours

Approx. 100 hours

DLP® Link

See the OPERATION MANUAL FOR STEREOSCOPIC 3D PROJECTION provided separately.

DLP® LinkTM Invert

See the OPERATION MANUAL FOR STEREOSCOPIC 3D PROJECTION provided separately.

Note

•

It is recommended that the lamp be changed when the remaining lamp life becomes 5%. The lamp life may vary depending on the

• usage condition.

Features

Useful

Setting Up the Projector Network Environment (“Network” Menu)

Menu operation n Page 40

Pict. Network

Password Disable

DHCP Client Off

TCP/IP

Reset Network Setting

Restart Network

SCRSIG PRJ1 PRJ2

IP Address MAC Address

Projector

Link

SEL./ADJ. ENTER END

Setting a Password

If you do not want others to change the setting for the “Network” menu, set a password.

a

Setting a Password

Select “Password”, then press

ENTER or Q.

•

The screen for entering the password appears.

Setting the Password

Old Password

New Password

Reconﬁrm

Press P or R to set the ﬁ rst digit

in “New Password”, then press Q.

Enter the remaining 3 digits, then

press ENTER.

•

To return to the previous digit, press O.

Enter the same password in

“Reconﬁ rm”, then press ENTER.

The status for “Password” changes to

• “Enable”.

Note

•

Once the password is set, you must enter the password to change the “Network” menu settings.

Changing the Password

Select “Password”, then press

ENTER or Q.

The screen for entering the password

• appears.

––––

–

–––

––––

XXX.XXX.XXX.XXX XX : XX : XX : XX : XX : XX XX-XXXX

 Disconnected

Network

•

If you do not need the password protection for the “Network” menu settings anymore, press ENTER without entering the new password in steps 3 and 4.

•

To cancel the password settings, press

RETURN.

If you forget the password

If you forget the password, perform the following procedure to delete it, then set a new password.

On the projector, press

Enter the password in “Old

Password” using P, R, Q and O, then press ENTER.

Enter the password in “New

Password” using P, R, Q and O, then press ENTER.

Enter the same password again

in “Reconﬁ rm” using P, R, Q and O, then press ENTER.

Note

•

If ENTER is held down for more than 5 seconds, the operation buttons on the projector will be locked. (See page You cannot use the buttons on the

• remote control to delete the password.

52.)

Menu operation n Page

DHCP Client Setting

Connect the LAN cable before turning the projector on. If not, the DHCP Client function does not work.

Selectable items Description

On Obtains conﬁ guration

Off Sets the TCP/IP manually.

Select “On” for “DHCP Client”. “Obtaining IP Address...” appears, then the menu screen appears. Conﬁ rm the parameters of IP Address, Subnet Mask and Gateway on the TCP/IP screen.

If the DHCP server is not available, “Could not obtain IP Address.” appears.

In this case, set the TCP/IP manually. (See the item 3.)

TCP/IP Setting

Set the TCP/IP manually.

Select “Off” for “DHCP Client”,

then press ENTER.

Select “TCP/IP”, then press

ENTER.

Enter “IP Address” using P, R, Q

and O, then press ENTER.

Setting the TCP/IP

IP Address

Subnet Mask Gateway

parameters for TCP/IP network automatically.

Network

92 .

68 .

50 .

55 .2

000 .

55 .2

000 .

55 .2

000 .

000

Selectable items Description

IP Address Factory default setting:

Subnet Mask Factory default setting:

Gateway Factory default setting:

Note

•

Conﬁ rm the existing network's segment (IP address group) to avoid setting an IP address that duplicates the IP addresses of other network equipment or computers. If “192.168.150.002” is not used in a network with an IP address of “192.168.150.XXX”, you don't have to change the projector IP address.

•

For details about each setting, consult your network administrator.

Returning to Default

192.168.150.00 2 Enter an IP address appropriate for the network.

255.255.255.000 Set the subnet mask to the same as that of the computer and equipment on the network.

000. 000. 000. 000 * When not in use, set to “000.

000. 000. 000”.

Settings (Network)

This function allows you to initialize the Network settings you have made in the projector.

Note

•

If the values for IP Address, Subnet Mask or Gateway of the projector have been returned to the default settings, the computer cannot be connected to the projector depending on the computer’s network settings.

Features

Useful

Enter “Subnet Mask” using P, R,

Q and O, then press ENTER.

Enter “Gateway” using P, R, Q

and O, then press ENTER.

Restart Network Function

Restarts the network function. Perform this function when the projector cannot be controlled via the network.

Setting Up the Projector Network Environment (“Network” Menu) (Continued)

Menu operation n Page 40

Conﬁ rming the

Projector Information

You can conﬁ rm the following items.

Selectable

items

IP Address The IP address of the projector is

MAC Address The MAC address of the projector is

Projector The projector name is displayed. Link Displays the network connection

Note

•

For information on how to change the projector name, see “SETUP MANUAL” contained in the supplied CD-ROM.

displayed.

status. Connected Connected to the

Disconnected Disconnected from

Description

network.

the network.

Maintenance

Cleaning the projector

Ensure that you have unplugged the power

■

cord before cleaning the projector. The cabinet as well as the operation panel is

■

made of plastic. Avoid using benzene or thinner, as these can damage the ﬁ nish on the cabinet. Do not use volatile agents such as

■

insecticides on the projector. Do not attach rubber or plastic items to the projector for long periods. The effects of some of the agents in the plastic may cause damage to the quality or ﬁ nish of the projector. Wipe off dirt gently with a soft ﬂ annel cloth.

■

Using a chemical cloth (wet/dry sheet type cloth, etc.) may deform the components of the cabinet or cause cracking. Wiping with a hard cloth or using strong

■

force may scratch the cabinet surface. When the dirt is hard to remove, soak a cloth

■

in a mild detergent diluted with water, wring the cloth well and then wipe the projector. Strong cleaning detergents may discolor, warp or damage the coating on the projector. Make sure to test on a small, inconspicuous area on the projector before use.

Mild detergent

Cleaning the lens

Use a commercially available blower or lens

■

cleaning paper (for glasses and camera lenses) for cleaning the lens. Do not use any liquid type cleaning agents, as they may wear off the coating ﬁ lm on the surface of the lens. As the surface of the lens can easily get

■

damaged, be careful not to scrape or hit the lens.

Cleaning the exhaust and intake vents

Use a vacuum cleaner to clean dust from the

■

exhaust vent and the intake vent.

Wax

Thinner

Mild detergent diluted

with water

Info

•

If you want to clean the air vents during projector operation, ensure you press

STANDBY/ON on the projector or STANDBY on the remote control and put the

projector into Standby mode. After the cooling fan has stopped, clean the vents.

Appendix

Maintenance Indicators

■

The warning lights (power indicator, lamp indicator and temperature warning indicator) on the projector indicate problems inside the projector.

■

If a problem occurs, either the temperature warning indicator or the lamp indicator will illuminate red, and the projector will enter Standby mode. After the projector has entered Standby mode, follow the procedures given below.

Top V i e w

About the temperature warning indicator

If the temperature inside the projector increases, due to blockage of the air vents, or the setting location, the temperature warning indicator will blink. And if the temperature keeps on rising, “ ” will illuminate in the lower left corner of the picture with the temperature warning indicator blinking. If this state continues, the lamp will turn off, the cooling fan will run and then the projector will enter Standby mode. When you ﬁ nd the temperature warning indicator blinking, be sure to perform the measures described on page 59.

About the lamp indicator

Temperature warning indicator

Lamp indicator

Power indicator

When the remaining lamp life becomes 5% or less, (yellow) and “Change The Lamp” will

■

be displayed on the screen. When the percentage becomes 0%, it will change to (red), the lamp will automatically turn off and then the projector will automatically enter Standby mode. At this time, the lamp indicator will illuminate in red.

If you tr y to turn on the projector a fourth time without replacing the lamp, the

■

projector will not turn on.

Indicators on the Projector

Power indicator Red on Normal (Standby)

Green on Normal (Power on) Red blinks Abnormal (See page Green blinks Normal (Cooling) Green and orange

blink alternately

Lamp indicator Green on Normal

Green blinks The lamp is warming up. Red on The lamp is shut down abnormally or requires to be

Temp eratu re warning indicator

Off Normal Red on/Red blinks The internal temperature is abnormally high. (See page

The lens shutter is closed. (See page

changed. (See page

59.)

30.)

59.)

Maintenance indicator

Temperature

warning

indicator

Lamp

indicator

Power

indicator

Green on

when the

warming

Green on/

(Cooling)

Normal Abnormal

Off Red blinks

(Green

blinks

lamp is

up.)

Red on

Green blinks

(On)/

Red on

(Standby)

Red on The lamp does

Red on

(Standby)

Red blinks The power

Problem Cause Possible Solution

The internal temperature is abnormally high.

not illuminate.

Time to change the lamp.

The lamp does not illuminate.

indicator blinks in red when the projector is on.

•

Temperatures around the projector are high. Blocked air intake

•

Cooling fan

• breakdown Internal circuit failure

• Clogged air intake

•

The lamp is shut

• Disconnect the power cord down abnormally.

Remaining lamp life

• Carefully replace the lamp. becomes 5% or less.

Burnt-out lamp

• Lamp circuit failure

•

The lamp unit cover

• If the power indicator blinks is open.

Use the projector in an

• area with a temperature of lower than 95°F (+35ºC). Relocate the projector to

• an area with proper ventilation. (See page

•

Take the projector to your nearest Sharp Authorized Projector Dealer or Service Center (see page repair.

• from the AC outlet, and then connect it again.

• (See page Take the projector to your

• nearest Sharp Authorized Projector Dealer or Service Center (see page repair. Please exercise care when

• replacing the lamp. Securely install the cover.

•

• in red even when the lamp unit cover are securely installed, contact your nearest Sharp Authorized Projector Dealer or Service Center (see page advice.

8.)

67) for

60.)

67) for

Info

•

If the temperature warning indicator illuminates, and the projector enters Standby mode, follow the possible solutions above and then wait until the projector has cooled down completely before plugging in the power cord and turning the power back on. (At least 10 minutes.)

•

If the power is turned off for a brief moment due to power outage or some other cause while using the projector, and the power supply recovers immediately after that, the lamp indicator will illuminate in red and the lamp may not be lit. In this case, unplug the power cord from the AC outlet, replace the power cord in the AC outlet and then turn the power on again.

•

The cooling fan keeps the internal temperature of the projector constant and this function is controlled automatically. The sound of the cooling fan may change during operation because the fan speed may change and this is not a malfunction.

Appendix

Regarding the Lamp

Lamp

It is recommended that the lamp (sold separately) be replaced when the remaining lamp life becomes

■

5% or less, or when you notice a signiﬁ cant deterioration in the picture and color quality. The lamp life (percentage) can be checked with the on-screen display. (See page Purchase a replacement lamp of type AN-D350LP from your place of purchase, nearest Sharp

■

Authorized Projector Dealer or Service Center.

IMPORTANT NOTE TO U.S. CUSTOMERS:

The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service of this projector under warranty, including lamp replacement, must be obtained through a Sharp Authorized Projector Dealer or Service Center. For the name of the nearest Sharp Authorized Projector Dealer or Service Center, please call toll-free: 1-888-GO-SHARP (1-888-467-4277).

Hg LAMP CONTAINS MERCURY For State Lamp Disposal Information www.lamprecycle.org or 1-800-BE-SHARP

Caution Concerning the Lamp

This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp failure

■

can be attributed to numerous sources such as: excessive shock, improper cooling, surface scratches or deterioration of the lamp due to a lapse of usage time. The period of time up to failure largely varies depending on the individual lamp and/or the condition and the frequency of use. It is important to note that failure can often result in the bulb cracking. When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended

■

In such a case, it is recommended you contact your nearest Sharp Authorized Projector Dealer or Service Center to assure safe operation. Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the

■

53.)

U.S.A ONLY

Replacing the Lamp

Caution

Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may cause

• burns or injury. Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully

• cool before removing the lamp unit.

Carefully change the lamp by following the instr uctions described in t his section.

■

* If you wish, you may have the lamp replaced at your nearest Sharp Authorized Projector

Dealer or Service Center.

* If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorized Projector

Dealer or Service Center for repair.

Removing and Installing the

Lamp Unit

Warning!

•

Do not remove the lamp unit from the projector right after use. The lamp and parts around the lamp will be very hot and may cause burns or injury.

Info

•

Do not touch the glass surface of the lamp unit or the inside of the projector.

•

To avoid injury to yourself and damage to the lamp, make sure you carefully follow the steps below. Do not loosen other screws except for the

• lamp unit cover and lamp unit.

Optional

accessory

Lamp unit

Lamp unit AN-D350LP

AN-D350LP

Press STANDBY/ON on the

projector or STANDBY on the remote control to put the projector into Standby mode.

Disconnect the power cord.

•

Unplug the power cord from the AC socket. Leave the lamp until it has fully cooled

• down (about 1 hour).

Remove the lamp unit cover.

•

Close the lens shutter and turn the projector over. Loosen the user service screw (1) that secures the lamp unit cover. Remove the lamp unit cover (2).

STANDBY/ON button

AC socket

User service screw

User service screw (for lamp unit cover)

(for lamp unit cover)

Appendix

Regarding the Lamp (Continued)

Remove the lamp unit.

•

Loosen the securing screw from the lamp unit. Hold the lamp unit and pull it in the direction of the arrow. At this time, keep the lamp unit horizontal and do not tilt it.

Insert the new lamp unit.

•

Press the lamp unit ﬁ rmly into the lamp unit compartment. Fasten the securing screw.

Replace the lamp unit cover.

•

Align the tab on the lamp unit cover (1) and close it (2). Then tighten the user service screw (3) to secure the lamp unit cover.

Info

•

If the lamp unit and lamp unit cover are not correctly installed, the power will not turn on, even if the power cord is connected to the projector.

Securing

Securing screw

screw

Resetting the Lamp Timer

Reset the lamp timer after replacing the lamp.

Info

•

Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and continue to use the same lamp, this may cause the lamp to become damaged or explode.

Connect the power cord and

open the lens shutter fully.

•

Plug the power cord into the AC socket of the projector.

Reset the lamp timer.

•

While simultaneously holding down MENU, ENTER and press STANDBY/ON on the projector and keep all four buttons pressed down until the lamp indicator starts blinking green. “LAMP 0000H” is displayed, indicating

• that the lamp timer is reset.

R on the projector,

AC socketAC socket

STANDBY/ON

STANDBY/ON button

button

ENTER button

MENU button

R button

Storing the Projector

How to Use the Storage Case

When storing the projector, close the lens shutter, and place it in the supplied storage case.

Open the cover of the storage

case.

Fold out the inner padding.

•

Place the projector into the

storage case.

Info

•

Ensure the projector has cooled down sufﬁ ciently before placing it in the case.

•

Ensure the lens shutter is closed for protection.

•

Place t he projector into the storage case with the lens facing the direction indicated in the illustration.

•

Ensure the projector is held in place by using the ﬁ xing band.

•

Do not expose the storage case to direct sunlight or near heat sources. The storage case may change color or become deformed.

Close the cover of the storage

case.

Place the accessories in the front

pocket of the storage case.

Lens shutter

Fixing band

Supplied accessories (Remote control, etc.)

Appendix

Computer Compatibility Chart

Computer

• Multiple signal support Horizontal Frequency: 15-110 kHz, Vertical Frequency: 45-85 Hz,

PC/MAC Mode Resolution

640 × 400

VGA

SVGA 800 × 600

MAC 13” VGA 640 × 480 34.9 67 MAC 16” SVGA 832 × 624 49.7 75 MAC 19” XGA 1024 × 768 60.2 75 TRUE

MAC 21” SXGA 1152 × 870 68.7 75

XGA 1024 × 768

WXGA

WXGA+ 1440 × 900 55.9 60

SXGA

SXGA+ 1400 × 1050

WSXGA+ 1680 × 1050 65.3 60

UXGA 1600 × 1200 75.0 60

720 × 400

640 × 480

1280 × 720 45.0 60 1280 × 768 47.8 60

1280 × 800

1360 × 768 47.7 60 1366 × 768 47.8 60

1152 × 864

1280 × 960

1280 × 1024

Horizontal frequency

[kHz]

27.0 60

31.5 70

37.9 85

27.0 60

31.5 70

37.9 85

26.2 50

31.5 60

34.7 70

37.9 72

37.5 75

43.3 85

31.3 50

35.2 56

37.9 60

46.6 70

48.1 72

46.9 75

53.7 85

40.3 50

48.4 60

56.5 70

60.0 75

68.7 85

49.7 60

62.8 75

55.0 60

66.2 70

67.5 75

60.0 60

75.0 75

64.0 60

80.0 75

64.0 60

65.3 60

Pixel Clock: 12-165 MHz Sync signal: Compatible with TTL level

• Compatible with sync on green signal

Verti cal

frequency[Hz]

Display

Upscale

TRUE

Intelligent

Compression

Upscale

Intelligent

Compression

Note

Optimum image quality will be achieved by matching your computer's output resolution to the

• resolution that corresponds to “TRUE” in the “Display” column shown above.

•

When “Screen resolution” of the computer is different from the resolution displayed on the projected image, follow the procedures shown below. – Refer to “Resolution” on the “SIG-ADJ” menu and select the same resolution as the resolution in

“Screen resolution” of the computer. Depending on the computer you are using, the output signal may not be faithful to the “Screen resolution”

–

adjustment. Check the settings of the computer's signal output. If the settings cannot be changed, it is recommended that the resolution be set to the one that corresponds to “TRUE” in the “Display” column.

DTV

Horizontal

Signal

Freque ncy (kHz)

15.7 60 720P 45.0 60

480 480P 31.5 60 540P 33.8 60

576 576P 31.3 50 1080P 56.3 50 720P 37.5 50 1080P 67.5 60

15.6 50

Vert ical

Freque ncy (Hz)

Signal

1035 1080 1080

Horizontal

Freque ncy (kHz)

33.8 60

28.1 50

33.8 60

Vert ical

Freque ncy (Hz)

Troubleshooting

Problem Check Page

Projector power cord is not plugged into the wall outlet.• Power to the external connected devices is off.• – The lens shutter is closed.• The selected Input mode is wrong.• 30 The AV Mute function is working.• 30

No picture and no sound

or projector does not

start.

Sound is heard but no

picture appears

(or picture is dark).

Dark or bluish image

Color is faded or poor.

Picture is blurred;

noise appears.

Cables are incorrectly connected to the projector.• 21–25 Remote control battery has run out.• 15 External output has not been set when connecting a notebook computer.

• 21 The lamp unit cover is not installed correctly.• 61, 62 Cables are incorrectly connected to the projector.• “Bright” is set to minimum position.• 43 Depending on the computer you are using, an image may not be

• projected unless the signal output setting of the computer is switched to the external output. Refer to the computer's operation manual for how to switch its signal output settings. Is “On” selected in “DLP

•

Check that “Wall Color” is conﬁ gured correctly.•

•

Image adjustments are incorrectly set.

•

Make adjustments of “Color” and “Tint” in “Picture Mode” and lower the “BrilliantColor

(S-Video, Video Input only)

•

Video input system is incorrectly set.

(COMPUTER/COMPONENT 1, 2 Input only)

Input signal type (RGB/Component) is incorrectly set.

•

Adjust the focus.• The projection distance exceeds the focus range.• 19 There is fog on the lens. If the projector is carried from a cold room into a

• – warm room, or if it is suddenly heated, condensation may form on the surface of the lens and the image will become blurred. Set up the projector at least one hour before it is to be used. If condensation should form, remove the power cord from the wall outlet and wait for it to clear.

(Computer Input only)

Perform “SIG-ADJ” Adjustments (“Clock” and “Phase” Adjustment)

• Noise may appear depending on the computer.

• Cables are incorrectly connected to the projector.•

•

Volume is set to minimum.

•

When the projector is connected to an external device and the volume is set to minimum, the sound is not output even if you turn up the volume of the external device.

” value.

LinkTM”?

26, 30

21–25

–

21–25

Picture appears but no

sound is heard.

Data image is not

centered.

An unusual sound is

occasionally heard from

the cabinet.

“Speaker” is set to “Off”.

• The Audio Mute function is working.

•

Make the necessary adjustments of each item in the “SIG-ADJ” menu.•

• –

Depending on the computer you are using, the output resolution signal may be different from the one you have set. For details, refer to the operation manual of the computer.

• –

If the picture is normal, the sound is due to cabinet shrinkage caused by room temperature changes. This will not affect operation or performance.

50 53

Appendix

Troubleshooting (Continued)

Problem Check Page

Maintenance indicator on

the projector illuminates

or blinks in red.

Picture is green on

COMPUTER (Component)

Picture is pink

(no green) on

COMPUTER (RGB)

Picture is too bright and

whitish.

The cooling fan becomes

The lamp suddenly turns

noisy.

The lamp does not light

up even after the

projector turns on.

off during projection.

The image sometimes

ﬂ i c k e r s .

The lamp needs much

time to turn on. Picture is dark.

The remote control

cannot be used.

See “Maintenance Indicators”.•

Change the input signal type setting.•

Image adjustments are incorrectly set.•

When temperature inside the projector increases, the cooling fan runs

• faster.

•

The lamp indicator is illuminating in red. Replace the lamp. The lens shutter is closed.

•

Cables are incorrectly connected to the projector or the connected equipment works improperly. If this happens frequently, replace the lamp.

• The lamp will eventually need to be changed.

• While the remaining lamp life draws to a close, replace the lamp.

•

Operate the remote control while pointing it at the projector's remote control sensor. The remote control may be too far away from the projector.

• If direct sunlight or a strong ﬂ uorescent lamp is shining on the

• projector's remote control sensor, place the projector where it will not be affected by strong light.

The batteries may be depleted or inserted incorrectly. Make sure the

• 15 batteries are inserted correctly or insert new ones.

This unit is equipped with a microprocessor. Its performance could be adversely affected by incorrect operation or interference. If this should happen, unplug the Unit and plug it in again after more than 5 minutes.

8, 9 57, 58, 5

58, 61, 62

26, 30

21–25

61 61

For SHARP Assistance

If you encounter any problems during setup or operation of this projector, ﬁ rst refer to the “Troubleshooting” section on pages manual does not answer your question, please contact the SHARP Service departments listed below.

65 and 66. If this operation

U.S.A. Sharp Electronics Corporation

1-888-GO-SHARP (1-888-467-4277)

http://www.sharpusa.com

Canada Sharp Electronics of Canada Ltd.

http://www.sharp.ca

Mexico Sharp Electronics Corporation

(525) 716-9000 http://www.sharp.com.mx

Latin America Sharp Electronics Corp. Latin

(305) 264-2277 www.servicio@sharpsec.com http://www.siempresharp.com

Germany Sharp Electronics (Europe) GMBH

01805-234675 http://www.sharp.de

U.K. Sharp Electronics (U.K.) Ltd.

08705 274277

Italy Sharp Electronics (Italy) S.P.A.

(39) 02-89595-1 http://www.sharp.it

France Sharp Electronics France

01 49 90 35 40 hotlineced@sef.sharp-eu.com http://www.sharp.fr

Spain Sharp Electronica Espana, S.A.

93 5819700 sharplcd@sees.sharp-eu.com http://www.sharp.es

Switzerland Sharp Electronics (Schweiz) AG

0041 1 846 63 11 cattaneo@sez.sharp-eu.com http://www.sharp.ch

Sweden Sharp Electronics ( Nordic ) AB

(46) 8 6343600 vision.support@sen.sharp-eu.com http://www.sharp.se

Austria Sharp Electronics (Europe) GMBH

Branch Ofﬁ ce Austria 0043 1 727 19 123 pogats@sea.sharp-eu.com http://www.sharp.at

lcdsupport@sharpsec.com

(905) 568-7140

Mexico Branch

American Group

http://www.sharp.co.uk/customersupport

Benelux SHARP Electronics Benelux BV

0900-SHARPCE (0900-7427723)

9900-0159 Belgium http://www.sharp.nl http://www.sharp.be http://www.sharp.lu

Australia Sharp Corporation of Australia Pty.

1300-135-022 http://www.sharp.net.au

New Zealand Sharp Corporation of New Zealand

Phone: (09) 573-0111 Fax: (09) 573-0112 http://www.sharp.net.nz

Singapore Sharp-Roxy Sales (S) Pte. Ltd.

65-226-6556 ckng@srs.global.sharp.co.jp http://www.sharp.com.sg

Hong Kong Sharp-Roxy (HK) Ltd.

(852) 2410-2623 dcmktg@srh.global.sharp.co.jp http://www.sharp.com.hk

Taiwan Sharp Corporation (Taiwan)

0800-025111 http://www.sharp-scot.com.tw

Malaysia Sharp-Roxy Sales & Service Co.

(60) 3-5125678

U.A.E. Sharp Middle East Fze

971-4-81-5311 helpdesk@smef.global.sharp.co.jp

Thailand Sharp Thebnakorn Co. Ltd.

02-236-0170 svc@stcl.global.sharp.co.jp http://www.sharp-th.com

Korea Sharp Electronics Incorporated of

lcd@sharp-korea.co.kr http://www.sharpkorea.co.kr

India Sharp Business Systems (India)

(91) 11- 6431313 service@sharp-oa.com

Nederland

Ltd.

Korea

(82) 2-3660-2002

Limited

Appendix

Speciﬁ cations

Model PG-D3510X/PG-D3010X PG-D2710X Display devices 0.55" DLP Resolution XGA (1024 × 768) Lens F number F 2.4 – 2.6

Input terminals Computer/Component

Output terminals

Control and communication terminals

Speaker 7W (Mono) Projection lamp 250 W 210 W Rated voltage AC 100 – 240 V Rated frequency 50/60 Hz Input current 3.2 A 2.8 A Power consumption Eco+Quiet

Power consumption (STANDBY Mode)

Operation temperature 41ºF to 95ºF (+5ºC to +35ºC) Cabinet Plastic Dimensions (main body only) [W × H × D] 11

Weight (approx.) 6.2 lbs. (2.8 kg)

Zoom Manual, ×1.20 (f = 19.0 – 22.7 mm) Focus Manual

(mini D-sub 15 pin) S-Video (mini DIN 4 pin) ×1 Video (RCA) ×1 Audio (ø3.5 mm stereo minijack) ×1 Audio (RCA) ×1 (L/R) Computer/Component

(mini D-sub 15 pin) Audio (ø3.5 mm stereo minijack) ×1 (variable audio output) LAN (RJ-45) ×1 USB (Type B) ×1 RS-232C (mini DIN 9 pin) ×1

Off

Eco+Quiet OnAC 100 V 215 W

Quick Start AC 100 V 3.6 W

Eco AC 100 V 0.32 W

AC 100 V 322 W 274 W AC 240 V 309 W 265 W

AC 240 V 210 W

AC 240 V 4.4 W

AC 240 V 0.77 W

×2

×1 (Shared with COMPUTER/COMPONENT 2; switchable)

(300 × 79 × 236 mm)

Chip ×1

/64" × 3 1/8" × 9 19/64"

As a part of policy of continuous improvement, SHARP reserves the right to make design and speciﬁ cation changes for product improvement without prior notice. The performance speciﬁ cation ﬁ gures indicated are nominal values of production units. There may be some deviations from these values in individual units.

This SHARP projector uses a DLP® chip. This very sophisticated panel contains 786,432 pixels (micromirrors). As with any high technology electronic equipment such as large screen TVs, video systems and video cameras, there are certain acceptable tolerances that the equipment must conform to. This unit has some inactive pixels within acceptable tolerances which may result in inactive dots on the picture screen. This will not affect the picture quality or the life expectancy of the unit.

Dimensions

Units: inches (mm)

/8 (79)

/32

/32 (10)

/64 (236)

(37.3)

(41.7)

/2 (38) 1

/32 (10)

11 52/64 (300)

1 31/32 (50)

/64 (75)

M4 M4

2 61/64 (75)

/32 (118)5 27/64 (137.5)

/32 (32.5)

/32

(16.5)

/16 (58.5)

/64 (104)

/16 (49)

/32 (218)

Appendix

Index

16:9·············································································31, 32 3D MODE button ······························································ 14

Accessories ······································································11 AC socket ·········································································25 Adjustment buttons ···················································· 39, 40 Adjustment foot ································································28 All Reset ···········································································53 AREA ZOOM ····································································32 Aspect ratio ······································································31 Audio input ·······································································30 AUDIO 1, 2 terminals ························································23 Audio Mute ·······································································53 AUDIO OUT terminal ························································23 Auto Power Off ·································································50 Auto Restart ·····································································50 Auto Sync (Auto Sync adjustment) ···························· 34, 50 AUTO SYNC button··························································34 AV MUTE button ······························································· 30

Background ······································································49 Batteries ···········································································15 Blue ··················································································49 BORDER ·····································································31, 32 BREAK TIMER button ······················································33 Bright ················································································43 BrilliantColor

Clock ················································································45 Closed Caption ································································· 48 CLR Temp (Color Temperature) ········································43 C.M.S. ··············································································43 Color ·················································································43 Complete Menu ································································40 COMPUTER2 Select ························································52 COMPUTER/ Contrast ············································································43

DHCP Client ·····································································55 DIN-D-sub RS-232C adaptor ···········································11 DLP DLP DNR ··················································································44

Eco+Quiet ··································································· 33, 44 ECO+QUIET button ··························································33 ENTER button ··································································· 39 Exhaust vent ·······························································12, 57

Fan Mode ·········································································51 Film Mode ········································································· 44 Focus ring ·········································································27 FREEZE button ·································································34 FULL ·················································································31 FUNCTION button ····························································14 FUNCTION Button setting ················································53

HEIGHT ADJUST lever ·····················································28 H-Pos ···············································································45

Image shift ········································································47 Information ·······································································40 INPUT modes ···································································30 Input Search Start ····························································40 Intake vent ··································································12, 57 IP Address ········································································ 56

Kensington Security Standard connector ························13 Keycode ··········································································51 Keylock ············································································52 KEYSTONE button ··························································29 Keystone Correction ··················································· 29, 47

Lamp ················································································60 Lamp indicator ·································································58 Lamp Timer (Life) ······························································53 Lamp unit ·········································································61 Language (on-screen display language) ··························49 LAN terminal ·····································································25 L-CLICK/EFFECT button ············································33, 35

·································································43

COMPONENT1, 2 input terminals

LinkTM ······································································53

LinkTM Invert ····························································53

········· 21, 22

Lens shutter ································································26, 30 Link ···················································································56

MAC Address ···································································56 MAGNIFY buttons ····························································34 MENU button ···································································· 39 MONITOR OUT terminal ···················································23 MOUSE/Adjustment buttons ······································35, 39

NATIVE ··············································································31 Network ············································································54 NORMAL ····································································31, 32

ON button ·········································································26 Optional accessories ························································11 OSD Display ····································································48 Overscan ··········································································48

PAGE DOWN button ·························································35 PAGE UP button ······························································· 35 Password ·········································································· 54 PDF ···················································································10 Phase ················································································ 45 Picture Adjustment ··························································42 Picture Mode ······························································ 34, 42 PICTURE MODE button ···················································34 POINTER button ·······························································33 Power cord ······································································· 25 Power indicator ································································58 PRJ-ADJ1/2 ······································································ 50 PRJ Mode ···································································20, 49

Quick Start Menu ·····························································40 R-CLICK/RETURN button ··········································35, 39

Red ···················································································43 Remote control ·································································14 Remote control sensor ····················································· 15 Replacing the lamp·····················································60, 61 Reset Network Setting ·····················································55 Resize ·········································································31, 47 RESIZE button ··································································31 Resolution·········································································45 Restart Network ·······························································55 RGB cable ········································································21 RS-232C terminal ·····························································24

SCR-ADJ ··········································································47 Screen Size and Projection Distance ·······························19 Security bar ······································································13 Setup Guide ·······························································27, 49 Sharp ················································································43 SIG-ADJ ···········································································45 Signal Info ········································································· 46 Signal Type ·······································································45 Speaker ············································································50 SPOT button ·····································································33 STANDBY button ······························································26 STANDBY Mode ·······························································53 STANDBY/ON button ·······················································26 Storage case ····································································63 Supplied accessories ·······················································11 S-VIDEO terminal ·····························································22 System Lock ·····································································51

TCP/IP ··············································································55 Temperature warning indicator ·········································58 Tint ···················································································· 43

USB terminal ····································································35 Video Setup ······································································46

Video System ···································································46 VIDEO terminal ·································································22 VOL (Volume) buttons ·······················································30 V-Pos ················································································45 V-STRETCH ······································································32

Wall Color ········································································· 49 Zoom ring ·········································································28

Singer PG-D3010X User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Introduction

How to Read this Operation Manual

Contents

IMPORTANT SAFEGUARDS

How to Access the PDF Operation Manuals

Accessories

Part Names and Functions

Front View

Top V i e w

Rear View (Terminals)

Inserting the Batteries

Usable Range

Easy Start

Setup and Projection

Setting Up the Projector

Setting Up the Projector

Standard Setup (Front Projection)

Screen Size and Projection Distance

Projection (PRJ) Mode

Ceiling-Mount Setup

Connecting the Projector to Other Equipment

Connections

Controlling the Projector by a Computer

Connecting the Power Cord

Turning the Projector On/Off

Turning the Projector On

Turning the Power Off (Putting the Projector into Standby Mode)

Image Projection

About the Setup Guide

Adjusting the Projected Image

Switching the Input Mode

Adjusting the Volume

Resize Mode

Operating with the Remote Control

Displaying and Setting the Break Timer

Displaying the Pointer

Using the Spot Function

Switching the Eco+Quiet Mode

Auto Sync (Auto Sync Adjustment)

Freezing a Moving Image

Displaying an Enlarged Portion of an Image

Selecting the Picture Mode

Using the Remote Control as the Wireless Computer Mouse

Menu Items

Using the Menu Screen

Menu Selections (Quick Start Menu)

Quick Start Menu

Menu Selections (Complete Menu)

Picture Adjustment (“Picture” Menu)

Selecting the Picture Mode

Adjusting the Image

Adjusting the Colors

Selecting the Film Mode

Reducing Image Noise (DNR)

Eco+Quiet

Signal Adjustment (“SIG-ADJ” Menu)

Adjusting the Computer Image

Signal Type Setting

Resolution Setting

Setting the Video System

Checking the Input Signal

Setting the Video Setup

Adjusting the Projected Image (“SCR-ADJ” Menu)

Keystone Correction

Setting the Resize Mode

Setting the Overscan

Closed Caption

Selecting the Setup Guide

Selecting the Wall Color

Adjusting the Projector Function (“PRJ-ADJ1/2” Menu)

Auto Power Off Function

Auto Restart Function

Speaker Setting

Fan Mode Setting

System Lock Function

Keylock Function