Singer ER10 User Manual
ER10
Instruction Manual
34074 Singer ER10 Manual.indd 1 6/30/08 10:00:29 AM
2
This household sewing machine is designed to comply with IEC/EN 60335-2-28 and UL1594
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic safety precautions should always be followed, including
the following:
Read all instructions before using this household sewing machine.
DANGER - To reduce the risk of electric
shock:
• A sewing machine should never be left unattended when plugged in. Always unplug this
sewing machine from the electric outlet immediately after using and before cleaning.
• Always unplug before relamping. Replace bulb with same type rated 15 Watt.
WARNING - To reduce the risk of burns,
re, electric shock, or injury to persons:
• Do not allow to be used as a toy. Close attention is necessary when this sewing machine is
used by or near children and in rm persons.
• Use this sewing machine only for its intended use as described in this manual. Use only
attachments recommended by the manufacturer as contained in this manual.
• Never operate this sewing machine if it has a damaged cord or plug, if it is not working
properly, if it has been dropped or damaged, or dropped into water. Return the sewing
machine to the nearest authorized dealer or service center for examination, repair, electrical or
mechanical adjustment.
• Never operate the sewing machine with any air openings blocked. Keep ventilation openings
of the sewing machine and foot controller free from the accumulation of lint, dust, and loose
cloth.
• Keep ngers away from all moving parts. Special care is required around the sewing machine
needle.
• Always use the proper needle plate. The wrong plate can cause the needle to break.
• Do not use bent needles.
• Do not pull or push fabric while stitching. It may de ect the needle causing it to break.
• Switch the sewing machine off (“0”) when making any adjustment in the needle area, such as
threading needle, changing needle, threading bobbin, or changing presser foot, etc.
• Always unplug sewing machine from the electrical outlet when removing covers, lubricating,
or when making any other user servicing adjustments mentioned in the instruction manual.
• Never drop or insert any object into any opening.
• Do not use outdoors.
• Do not operate where aerosol (spray) products are being used or where oxygen is being
administrated.
• To disconnect, turn all controls to the off (“0”) position, then remove plug from outlet.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
• The sound pressure level under normal operating conditions is 70dB(A).
SAVE THESE INSTRUCTIONS
3
English
Table of Contents .......................................... 3
Overview of the machine ............................. 3
Accessories ......................................................4
Setting Up ........................................................ 4
Attaching the power cord and foot control 4
Machine speed ...............................................4
For the USA and Canada .............................. 4
Cloth Presser ................................................... 5
Getting Started ...............................................6
Fabric and trims that can be used ................ 6
Laundering embellished projects .................6
NOTE: Laundering rules of
“pre-washing”: ................................................6
Start Embellishing .......................................... 7
Flat Bed Extension / Free Arm................... 8
Accessory Storage .......................................... 8
Maintenance ....................................................9
Changing the needle(s) .................................9
Replacing the light bulb...............................10
Cleaning the lint box ....................................10
Trouble Shooting ......................................... 11
Needle bent or Needle breakage .............. 11
Speci cations ................................................11
Overview of the machine
1. Handwheel
2. Socket for foot control
3. Power switch
4. Needle clamp holder
5. Needle plate
6. Flat Bed Extension
7. Accessory storage
8. Cloth presser height adjusting screw
9. Clear fabric cover with needle guard
10.
Connection socket
Table of Contents
34074 Singer ER10 Manual.indd 2 6/30/08 10:00:30 AM
3
English
Table of Contents .......................................... 3
Overview of the machine ............................. 3
Accessories ......................................................4
Setting Up ........................................................ 4
Attaching the power cord and foot control 4
Machine speed ...............................................4
For the USA and Canada .............................. 4
Cloth Presser ................................................... 5
Getting Started ...............................................6
Fabric and trims that can be used ................ 6
Laundering embellished projects .................6
NOTE: Laundering rules of
“pre-washing”: ................................................6
Start Embellishing .......................................... 7
Flat Bed Extension / Free Arm................... 8
Accessory Storage .......................................... 8
Maintenance ....................................................9
Changing the needle(s) .................................9
Replacing the light bulb...............................10
Cleaning the lint box ....................................10
Trouble Shooting ......................................... 11
Needle bent or Needle breakage .............. 11
Speci cations ................................................11
Overview of the machine
1. Handwheel
2. Socket for foot control
3. Power switch
4. Needle clamp holder
5. Needle plate
6. Flat Bed Extension
7. Accessory storage
8. Cloth presser height adjusting screw
9. Clear fabric cover with needle guard
10.
Connection socket
Table of Contents
34074 Singer ER10 Manual.indd 3 6/30/08 10:00:31 AM
4
1. Screwdriver
2. 1,5 mm Allen wrench
3. Needles
4. Cleaning brush
5. Machine cover
6. Instruction book
Setting Up
Attaching the power cord and
foot control
Plug the power cord into machine socket,
then into a wall outlet. Always make sure the
power is OFF and remove the plug from the
wall outlet when the machine is not in use,
or when making any adjustments such as
changing needles or light bulb.
Note: Before plugging in, check to ensure that
the foot control is of type “4C-337G” or
“C-9000”.
Machine speed
The machine speed is adjusted by increasing
or decreasing the pressure on the foot
control.
When not in use, do not place anything on
the foot control to prevent damage to the
foot control or motor.
For the USA and Canada
This sewing machine has a polarized
plug (one blade wider than the other).
To reduce the risk of electric shock,
this plug is intended to t in a polarized
outlet only one way. If the plug does not
t fully in the outlet, reverse the plug.
If it still does not t, contact a quali ed
electrician to install the proper outlet.
Do not modify the plug in any way.
Accessories
5
English
Cloth Presser
The cloth presser is to prevent cloth/fabric/
materials from lifting during the felting
process.
1. Place the cloth/fabric/materials on the
needle plate and under the cloth presser.
2. Loosen the cloth presser height adjusting
screw to adjust the height of the cloth
presser.
3. Move the clear fabric cover with needle
guard up or down until the red indicator
on the presser bar aligns with the correct
height for the thickness of your fabric
and felting material.
L= low position for thin or medium fabrics.
M= medium position for medium weight
fabrics.
H= high position for heavy or thick fabrics.
4. Tighten the clear fabric cover height
adjusting screw.
Note: The fabric and felting material must move
freely under the clear fabric cover with needle guard
without any restrictions.
34074 Singer ER10 Manual.indd 4 6/30/08 10:00:32 AM
Loading...