Singer EFSNG917 User Manual

Household Steam Iron

EFSNG917.4

instruction manual

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING.

Save these instructions in a safe place for future reference.

1. Use appliance only for its intended use.

2. To protect against risk of electrical shock, do not immerse the iron in water or other liquids. Never immerse the iron, cable or plug in any liquid.

3. This appliance should always be turned to “OFF” before plugging or unplugging from an outlet. Never yank the cord to disconnect from outlet, always grasp plug and pull to disconnect.

4. Always disconnect the appliance from the electrical outlet when ﬁlling with water or emptying or when not in use. Do not ﬁll the reservoir with water before removing the plug from the socket.

5. Do not allow cord to touch hot surfaces. Let the iron cool completely before storing. Loop cord loosely around iron when storing.

6. Do NOT operate appliance with a damaged cord, or if the appliance has been dropped or damaged. If electrical cord is damaged it must be replaced by the manufacturer or authorized service agent to avoid a safety hazard.

7. To avoid the risk of electrical shock, do NOT disassemble the iron. Ship to the nearest authorized SINGER® approved service center for examination and repair. Incorrect reassembly or repair can cause a risk of ﬁre, electrical shock or injury when the appliance is used.

8. Not intended for use by children. Close supervision is necessary for any appliance being used near children. Unsupervised use can result in ﬁre or personal injury. Do not leave appliance unattended while plugged in, on an ironing board, or while it is still hot. Do not leave the appliance unnecessarily plugged in. Disconnect the plug from the socket when the appliance is not being used.

9. Burns can occur from touching hot metal parts, hot water or steam. Use caution when you turn a steam iron upside down as there may be hot water in the reservoir.

10. Never use or rest the iron on an unstable surface. Do not leave the hot iron touching fabrics or very inﬂammable surfaces.

11. When iron is hot, never set on an unprotected surface.

12. Do not leave the appliance exposed to outside weather.

SPECIAL INSTRUCTIONS:

To avoid a circuit overload, do not operate another high-wattage appliance on the same circuit. If an extension cord is absolutely necessary, a 10-amp cord should be used. Cords rated with less amperage may overheat. Use care to arrange the cord so that it cannot be pulled or tripped over.

SAVE THESE INSTRUCTIONS

WARNING: THE POWER CORD ON THIS PRODUCT CONTAINS LEAD, A CHEMICAL KNOWN TO THE STATE OF CALIFORNIA TO CAUSE BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM. WASH HANDS AFTER HANDLING.

FOR HOUSEHOLD USE ONLY

Getting to Know Your SINGER® Iron

1312

1. Spray Nozzle

2. Steam Adjust Button

3. LCD Display

4. Cool Mist Spray Button

5. Burst of Steam Button

6. 360º Swivel Cord

7. Filler Door

8. Temperature Control Settings

9. Maximum Filling Line

10. Self-Cleaning Button

11. Soleplate with Steam Vents

12. Temperature UP Button

13. Temperature DOWN Button

LCD PANEL DESCRIPTION

A B

A. Smart Auto-Off

Indicator B. Steam Indicator C. Heating Indicator

D. Temperature Level

Indicator

E. Fabric Guide

TECHNICAL SPECIFICATIONS: Voltage: 120V, 60 Hz Power: 1700 Watts

WARNING: TO AVOID FIRE, NEVER LEAVE IRON UNATTENDED WHILE PLUGGED IN.

OPERATING INSTRUCTIONS

Before First Use

• Remove any protective ﬁlms or stickers from the soleplate and the iron.

• Read all safety and operating instructions.

• Fill the water tank as described in the “Filling the Water Tank” section.

• To turn the iron on, plug into a grounded electrical outlet. An audible beep

sound will indicate the iron is on. The LCD Display will illuminate and the will begin to ﬂash.

• To begin heating, press the Temperature UP (+) button. The LCD Display will begin to ﬂash HEATING and will indicate the temperature setting. An audible beep sound will indicate that the temperature is being adjusted.

• Select the maximum temperature by pressing the Temperature UP (+) button untilthedisplayindicatesMAX•••200ºC.

• When the selected temperature is reached, HEATING on the LCD Display will

stop ﬂashing and disappear, indicating that the iron is ready to use.

• Press the Steam Adjust Button located above the LCD Display to activate the steam setting . An audible beep will sound.

• On an ironing board or protected surface, iron an old towel or other heavy material until the water tank is empty and no more steam is produced.

• It is normal for a small amount of smoke and a light odor to be produced the ﬁrst time the iron is used. This will disappear quickly.

• Particles may emit from the iron the ﬁrst time it is used. They are not harmful and should disappear after the iron has been used as described above.

• Consult the garment’s label for temperature instructions or use the chart on page 6 of this manual for recommendations.

Filling the Water Tank

• Ensure iron is unplugged.

• Open the Filler Door located on the base of the iron.

• Using the ﬁlling cup provided, ﬁll the water chamber to the max mark.

• Close the Filler Door.

• To reﬁll the water tank during ironing, always unplug the iron. When you

return to ironing, make sure the iron reheats to the desired temperature and the LCD Display stops ﬂashing before continuing.

Water Recommendations

• SINGER® Home Essentials irons are designed to be used with regular tap water.

• If your water is especially hard or if you use a water softener, try using inexpensive bottled spring water.

• Never use water with additives, including scents, starches, or fabric conditioners, as they can cause deposits to form in the iron that can stain clothing.

WARNING: ALWAYS MAKE SURE THE IRON IS UNPLUGGED BEFORE FILLING WITH WATER OR COMING INTO CONTACT WITH LIQUID OF ANY KIND.

Turning the Iron On and Off

• To turn the iron on, plug into a grounded electrical outlet. An audible beep sound will indicate the iron is on. The LCD Display will illuminate and the will begin to ﬂash.

• To cool, adjust the Temperature DOWN (-) until the LCD Display no longer shows a temperature setting. The will begin to ﬂash.

• To turn the iron completely off, unplug from the grounded electrical outlet.

NOTE: Never yank the cord to disconnect from outlet. Always grasp plug and pull to disconnect.

Temperature UP Button Temperature DOWN Button

Selecting the Temperature

CONSULT THE GARMENT’S LABEL FOR TEMPERATURE INSTRUCTIONS.

WE RECOMMEND USING THE CHART BELOW AS A GUIDE.

Temperature Control Settings

synthetics

silk

wool

cotton linen do not iron

MAX

• To turn the iron on, plug into a grounded electrical outlet. An audible beep sound will indicate the iron is on. The LCD Display will illuminate and the will begin to ﬂash.

• Select the desired temperature by pressing the Temperature UP (+) and Temperature DOWN (-) buttons on either side of the LCD Display. An audible beep will sound each time the temperature is changed.

• When the selected temperature is reached, HEATING on the LCD Display will stop ﬂashing and disappear, indicating that the iron is ready to use.

• If steam ironing is desired, a minimum temperature setting of 160º C is required. To activate, press the Steam Adjust Button located above the LCD Display to activate the steam setting . An audible beep will sound.

IRONING YOUR GARMENTS

Dry Ironing

• Turn the iron on as described in the “Turning the Iron On and Off” section.

• Dry iron is the automatic setting.

• Select the desired temperature by pressing the Temperature UP (+) and

Temperature DOWN (-) buttons on either side of the LCD Display. An audible beep will sound each time the temperature is changed.

• When the selected temperature is reached, HEATING on the LCD Display will stop ﬂashing and disappear, indicating that the iron is ready to use.

• If the steam setting is the current selection, press the Steam Adjust Button located above the LCD Display to deactivate the steam setting. An audible beep will sound.

• To iron garments with a dry iron, SINGER® recommends using this iron with an empty water tank.

Steam Ironing

WARNING: NEVER IRON OR STEAM CLOTHES WHILE THEY ARE BEING WORN. NEVER DIRECT THE STEAM JET AT PEOPLE OR ANIMALS.

• Fill the water tank as described in “Filling the Water Tank” section.

• Turn the iron on as described in the “Turning the Iron On and Off” section.

• Select the desired temperature by pressing the Temperature UP (+) and

Temperature DOWN (-) buttons on either side of the LCD Display. An audible beep will sound each time the temperature is changed.

• A minimum temperature setting of 160º C is required for steam ironing.

• To activate, press the Steam Adjust Button located above the LCD Display to

activate the steam setting . An audible beep will sound.

Burst of Steam

This function is ideal for removing stubborn wrinkles or pressing extra-sharp creases.

WARNING: NEVER IRON OR STEAM CLOTHES WHILE THEY ARE BEING WORN. NEVER DIRECT THE STEAM JET AT PEOPLE OR ANIMALS.

• Follow the instructions as described in the “Steam Ironing” section.

• While steam ironing, press the Burst of Steam button every 4 to 5

seconds. Most wrinkles can be removed within three bursts.

NOTE: It may be necessary to press the Burst of Steam button a few times to

start this function. For optimum steam quality, do not operate the Burst of Steam more than three times in succession.

Vertical Burst of Steam

This feature enables you to remove wrinkles from hanging garments (jackets, coats, shirts), hanging curtains or other hanging fabric.

WARNING: NEVER IRON OR STEAM CLOTHES WHILE THEY ARE BEING WORN. NEVER DIRECT THE STEAM JET AT PEOPLE OR ANIMALS.

• Follow the instructions as described in the “Steam Ironing” section.

• Hold the iron upright, 6-12 inches away from the garment.

• Press the Burst of Steam button to direct steam at the area.

• Steam will penetrate into the garment, removing the wrinkles.

• For stubborn wrinkles, wait 4 to 5 seconds before pressing the Burst of

Steam button again. Most wrinkles can be removed within three bursts.

NOTE: Maintain a distance of 6-12 inches from delicate fabric (synthetics, silk,

velvet, etc.), otherwise the fabric could be damaged. It may be necessary to press the Burst of Steam button a few times to start this

function. For optimum steam quality, do not operate the Burst of Steam more than three times in succession.

Burst of Steam Button

Burst of Steam

Vertical Burst of Steam

Cool Mist Spray

The Cool Mist Spray function can be used on any temperature setting. Use the spray to dampen fabrics in order to remove tough wrinkles.

• Aim the nozzle at the garment.

• Press the Cool Mist Spray Button. You may need to press the button a few

times before the water sprays at full pressure.

• Iron as usual.

• DO NOT SPRAY SILK.

Cool Mist SprayCool Mist Spray Button

3-Way Smart Auto-Off

The SINGER® Expert Finish™ II Iron is equipped with an automatic shut-off. The Smart Auto-Off switches the iron off if it has been left unattended.

NOTE: Auto-Off is not an on/off switch. Always unplug the iron when it is not in use.

• If the iron is left on and is not moved for 8 minutes in a vertical position, it will automatically shut off and an audible beep will sound.

• If the iron is left on its soleplate or tipped over, it will shut off after 30 seconds and an audible beep will sound.

• When the iron is preparing to shut off, the will start ﬂashing on the LCD Display Panel and several audible beeps will sound. The LCD back light will turn off after 30 seconds.

• To de-activate the Auto-Off, move the iron or shake gently. The iron will take about 60 seconds to reach the previous soleplate temperature.

• Turn the iron completely off as described in the “Turning the Iron On and Off” section.

Anti-Drip

This iron is designed to reduce dripping and spitting while in use. Steam is automatically disabled when the soleplate temperature is too low to create steam, preventing spitting or dripping.

The Anti-Drip system may make a loud clicking sound during use. This is normal and indicates that the system is functioning correctly.

Anti-Calc System

The built-in Anti-Calc cartridge is designed to reduce the buildup of mineral substances in the water which occurs during steam ironing, thereby extending the life of your SINGER® Expert Finish™ II Iron. However, please note that the anti-calc cartridge will not completely stop the natural process of lime scale buildup.

CLEANING AND STORAGE

Self-Cleaning

This feature removes loose minerals and other impurities that have been built up in the steam chamber. It is recommended that this function be performed at least once a month or more regularly depending on the hardness of the water used.

WARNING: THE SELF-CLEAN FUNCTION WILL CAUSE HOT STEAM AND WATER TO BE EJECTED FROM THE SOLEPLATE. TAKE ALL PROPER PRECAUTIONS AND HOLD IRON AWAY FROM BODY. STEAM AND WATER ARE VERY HOT AND CAN CAUSE BURNS.

• Fill the water tank half way, as described in the “Filling the Water Tank” section.

• Place the iron on its heel on a ﬂat surface.

• Plug the iron into a grounded outlet.

• Turn the iron on as described in the “Turning the Iron On and Off” section.

• SelecttheMAX•••200ºCtemperaturesettingbypressingtheTemperature

UP (+) button.

• TheMAX•••200ºCtemperaturehasbeenreachedwhenHEATINGisno

longer visible on the LCD Display.

• Turn the iron completely off as described in the “Turning the Iron On and Off”

section.

• Hold the iron horizontally over a sink with the soleplate pointing away from the body and press and hold the Self-Cleaning Button. Steam and hot water will drain from the soleplate holes, washing away the scales and minerals that have built up inside the steam chamber.

• Gently move the iron back and forth until the water tank is empty.

• When self-cleaning is complete, release the Self-Cleaning Button.

• Place iron on its heel and let it cool completely.

• Carefully wipe all water from the soleplate with an old towel, as the water and

minerals may leave stains.

NOTE: Before using the iron after self-cleaning, test the steam and burst of

steam on an old towel or cloth that can be discarded.

Self-Cleaning Button

Emptying and Storing

• Unplug the iron.

• Place the iron on its heel and allow to cool completely.

• Empty water from the iron before storing.

• To protect the soleplate, store the iron on its heel.

Cleaning the Soleplate

In normal use, a coating may build up on the soleplate from starch, detergent or burnt synthetic ﬁbers. This can be easily removed by using a quality iron soleplate cleaner.

When the iron is cold and unplugged, the iron can be cleaned with a damp cloth and wiped dry.

NOTE: Never use abrasive household cleaners or other chemical agents to

clean the iron.

Never use sharp or rough objects to remove deposits on the soleplate.

TROUBLESHOOTING

PROBLEM REASON & SOLUTION

• The iron is not properly plugged in.

Iron does not heat

• The temperature setting is too low – set the temperature to a higher setting.

• Auto-Off has been engaged – move or shake the iron gently to de-activate Auto-Off.

No steam or not enough steam

Iron is emitting small particles or odor

Iron is dripping water from steam vents

• The water tank may be low or empty – add water.

• The iron is not set to steam setting – for maximum steam, temperatureshouldbeonMAX•••200ºC.

• This is normal – follow instructions for ﬁrst time use.

• Water may need to be changed.

• Buildup of mineral deposits inside steam chamber –

see “Self-Cleaning” section.

• Overﬁlled – do not ﬁll past the MAX line on water tank.

• The iron may not be hot enough – set the temperature toMAX•••200ºC.

• Over use of Burst of Steam – allow more time between

bursts.

If troubleshooting does not solve the problem, please call SINGER® at 1-800-4SINGER (1-800-474-6437).

SINGER® SEWING COMPANY LIMITED WARRANTY

EXPERT FINISH™ II STEAM IRON

IMPORTANT: SAVE THIS DOCUMENT AND KEEP IT IN A SAFE PLACE

What Does This Limited Warranty Cover?

The SINGER® Expert Finish™ II Steam Iron is warranted to be free from defects in material and workmanship.

How Long Is This Limited Warranty?

The warranty for the IRON’s wiring and electronic parts is for a period of two (2) years from the date of purchase. The warranty for all other parts of the IRON is for a period of ninety (90) days from the date of purchase.

What Will SINGER Do?

If the electronic parts and/or the other parts in the IRON, after inspection by SINGER, prove to be defective during the applicable warranty period(s), the electronic parts and/or the other parts will be repaired or replaced at SINGER’s option, without charge, except for any expense associated with sending the IRON to SINGER.

If SINGER sends a replacement IRON, it will carry the remaining warranty of the original IRON.

Who Is Covered By This Limited Warranty?

This warranty may only be used by the original consumer owner of the IRON and may not be transferred or assigned.

What Are The Other Exclusions or Limitations?

• Service under this warranty may only be obtained within the 48 contiguous states, Alaska, Hawaii and Canada.

• The IRON is warranted only for normal household (non-commercial) use. This warranty does not cover defect(s) caused by abuse, lack of maintenance or other neglect, failure to follow the care, cleaning or other instructions for the IRON, misuse, or events beyond our control.

• ANY IMPLIED WARRANTY APPLICABLE TO THE IRON, INCLUDING WITHOUT LIMITATION THE WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE, IS LIMITED IN DURATION TO THE DURATION OF THIS WRITTEN WARRANTY. SINGER SHALL NOT BE LIABLE FOR CONSEQUENTIAL ECONOMIC DAMAGES RESULTING FROM BREACH OF THIS WARRANTY OR ANY IMPLIED WARRANTY.

• SINGER does not authorize any person to create for it any obligation or liability in connection with the IRON and any of its parts beyond those set forth in this warranty.

• SINGER disclaims liability under this warranty for any damage or defect resulting from the use of other than SINGER parts and SINGER approved service in the repair and maintenance of the IRON.

+ 31 hidden pages