Simrad HH36 User Manual

simrad-yachting.com
ENGLISH
HH36
Marine Handheld VHF Radio with GPS
User Guide
Simrad® is a registered trademark of Navico
It is the owner’s sole responsibility to install and use this instrument in such a man­ner that will not cause accidents, personal injury or property damage.
Simrad disclaims all liability for any use of this product in a way that may cause ac­cidents, damage or that may violate the law.
Governing Language: This statement, any instruction manuals, user guides and other information relating to the product (Documentation) may be translated to, or has been translated from, another language (Translation). In the event of any conict between any Translation of Documentation, the English language version of the Documentation will be the ocial version of the Documentation.
This manual represents the HH36 radio at the time of printing. Simrad reserves the right to make changes to specications without notice.
No part of this manual may be copied, reproduced, republished, transmitted or distributed for any purpose, without prior written consent of Simrad.
Any unauthorized commercial distribution of this manual is strictly prohibited.
Simrad may nd it necessary to change or end policies, regulations, and special oers at any time. We reserve the right to do so without warning. All features and specications are also subject to change without warning. All screens in this manual are simulated.
For free owner’s manuals and the most current information on this product, its operation and accessories, visit our web site: www.simrad-yachting.com
Important safety information
Please read carefully before installation and use.
DANGER
This is the safety alert symbol. It is used to alert you to poten­tially hazardous situations. Obey all safety messages that follow this symbol to avoid possible injury or death.
WARNING
WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury
CAUTION
CAUTION indicates a potentially hazardous situation which, if not avoided, could result in minor or moderate injury.
CAUTION
CAUTION used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result in property damage.
Simrad - HH36 Installation and Operation Instructions 3
Contents
Safety and operational information .................................................................7
Important ...........................................................................................................................................................................8
Safety Information ........................................................................................................................................................8
Section 1 - General information ........................................................................9
Section 2 - Controls and keys ........................................................................... 10
2-1 Keys/Controls and functions ....................................................................................................... 11
2-1-1 Use of Softkeys in this radio....................................................................................................................13
2-1-2 DSC Softkeys .................................................................................................................................................... 14
Section 3 - Operating the radio .......................................................................15
3-1 Power On/O ................................................................................................................................... 15
3-2 Adjusting the Squelch level ....................................................................................................... 15
3-3 Volume control ................................................................................................................................ 15
3-4 Channel selection .......................................................................................................................... 16
3-5 Receiving and transmitting ........................................................................................................ 16
3-6 Dual Watch operation ................................................................................................................... 17
3-7 3CH operation (Favorite Channel) ........................................................................................... 17
3-7-1 Add a favorite channel for the first time .........................................................................................17
3-7-2 Modify or delete favorite channel ......................................................................................................17
3-8 Scan Operation ............................................................................................................................... 18
3-9 Navigation mode ........................................................................................................................... 18
3-10 WP select mode ............................................................................................................................ 19
3-11 Plotter mode ................................................................................................................................ 19
3-12 GPS satellite mode ...................................................................................................................... 20
Section 4 - Advanced setup .............................................................................. 21
4-1 Waypoint ............................................................................................................................................ 22
4-1-1 Add a new waypoint ...................................................................................................................................22
4-1-2 Edit a waypoint ...............................................................................................................................................23
4-1-3 Delete a waypoint ........................................................................................................................................24
4-1-4 Set a route to a stored waypoint ........................................................................................................24
4-2 Backlight adjustment ................................................................................................................... 25
4-3 Lamp timer ....................................................................................................................................... 25
4-4 Buddy list (Manage your buddy list) ........................................................................................ 26
4-4-1 Add a new buddy name ...........................................................................................................................26
4-4-2 Edit a buddy name .......................................................................................................................................27
Simrad - HH36 Installation and Operation Instructions4
4-4-3 Delete a buddy name.................................................................................................................................27
4-5 Contrast adjustment ..................................................................................................................... 28
4-6 GPS/DATA .......................................................................................................................................... 28
4-6-1 Manual (Manually enter your position and UTC time) ...........................................................29
4-6-2 Settings: LL display (Show or hide your position) .....................................................................29
4-6-3 Settings: Time display (Show or hide the time) ..........................................................................30
4-6-4 Time offset (Local time) .............................................................................................................................30
4-6-5 Settings: Time format (12 or 24 hour clock) .................................................................................. 31
4-6-6 Settings: COG/SOG (Course & speed display options) ...........................................................32
4-6-7 GPS alert..............................................................................................................................................................32
4-6-8 Turn GPS ENABLE on/off ...........................................................................................................................33
4-6-9 Set Magnetic Variation (MAG VAR) .....................................................................................................33
4-7 Radio setup ....................................................................................................................................... 34
4-7-1 Channel Bank selection (UIC) ................................................................................................................34
4-7-2 Channel name editing (CH NAME) ....................................................................................................34
4-7-3 Ring volume adjustment (RING VOLUME) .....................................................................................35
4-7-4 Beep volume adjustment (KEY BEEP) ...............................................................................................35
4-7-5 Select unit (UNITS) ........................................................................................................................................35
4-7-6 Set the Priority channel (WATCH MODE) ........................................................................................36
4-7-7 Weather alerts (WX ALERT) ..................................................................................................................... 36
4-7-8 Set NMEA output (NMEA OUT) ............................................................................................................ 36
4-7-9 Favorite Channel Setup (FAV CH SETUP).........................................................................................37
4-8 DSC setup ........................................................................................................................................ 38
4-8-1 Enter or check your user MMSI (USER MMSI) ...............................................................................38
4-8-2 Maintain groups (GROUP SETUP) ........................................................................................................39
4-8-2-1 Enter your groups ............................................................................................................................39
4-8-2-2 Edit groups .......................................................................................................................................... 40
4-8-2-3 Delete a group .................................................................................................................................. 40
4-8-3 Response to individual calls (INDIV REPLY) ...................................................................................41
4-8-4 Enable DSC functionality (DSC SELECT) .........................................................................................41
4-8-5 Response type to LL polling calls (LL REPLY) ..............................................................................42
4-8-6 Automatic Channel switching (AUTO SWITCH) ........................................................................42
4-8-7 DSC Test Reply (TEST REPLY) ................................................................................................................. 43
4-8-8 Set the inactivity timer (TIMEOUT) ...................................................................................................43
4-9 ATIS SETUP (EU only) ..................................................................................................................... 44
4-9-1 Enter or check your ATIS MMSI (ATIS MMSI) .................................................................................44
4-9-2 Enable ATIS functionality (ATIS SELECT ) ..........................................................................................45
4-10 Get Buddy ...................................................................................................................................... 45
4-11 Track log ........................................................................................................................................... 46
4-12 Erase track ....................................................................................................................................... 46
4-13 Reset (Reset to factory defaults) ............................................................................................. 46
Simrad - HH36 Installation and Operation Instructions 5
Section 5 - Sending and Receiving DSC Calls ..................................................47
5-1 What is DSC? .................................................................................................................................... 47
5-1-1 Maritime mobile service identity ........................................................................................................47
5-1-2 How can I obtain a MMSI number? ...................................................................................................47
5-2 DSC call types .................................................................................................................................. 48
5-3 Send an Individual call (INDIVIDUAL) ...................................................................................... 49
5-3-1 Call to a Buddy ................................................................................................................................................49
5-3-2 Call to others ....................................................................................................................................................49
5-4 Reply to the Last Call (LAST CALL) ............................................................................................ 50
5-5 Send a Group call (GROUP) .......................................................................................................... 50
5-6 Send an All Ships call (ALL SHIPS) ............................................................................................. 51
5-7 Send using the Call Log (CALL LOG)........................................................................................ 51
5-8 Send using the Distress Log (DISTRS LOG) ............................................................................ 52
5-9 Request the LL position of a buddy (LL REQUEST) ............................................................ 53
5-10 Track your buddy request (TRACK BUDDY) ......................................................................... 53
5-10-1 Add or delete a buddy (TRACKLIST) ...............................................................................................53
5-10-2 Select your TRACK BUDDY ....................................................................................................................54
5-10-3 Set the time interval of tracking .......................................................................................................54
5-10-4 Start tracking ................................................................................................................................................. 55
5-11 Make a DSC test call (DSC TEST) .............................................................................................. 55
5-11-1 Send a DSC TEST call ................................................................................................................................55
5-11-2 Receiving an incoming DSC TEST call reply (DSC TEST ACK) ..........................................56
5-11-3 Acknowledging an incoming DSC TEST call .............................................................................56
5-12 View User MMSI and GPS information .................................................................................. 56
5-13 Receiving DSC Calls ..................................................................................................................... 57
5-14 Receiving an All Ships Call (ALL SHIPS) ................................................................................. 57
5-15 Receiving an Individual Call (INDIV) ...................................................................................... 58
5-16 Receiving a Group Call (GROUP) ............................................................................................. 58
5-17 Receiving a Geographic Area Call (GEOGRAPH) ................................................................ 59
5-18 Receiving a Polled Position Call (POSITION) ....................................................................... 59
Section 6 - Distress calls ...................................................................................60
6-1 Send a Distress call ......................................................................................................................... 60
6-2 Receiving a Distress Call (DISTRESS!) ....................................................................................... 62
6-3 Distress Acknowledgement (DISTRESS ACK) or Distress Relay All Ships
(DISTRESS REL) .................................................................................................................................. 62
6-4 Distress Relay Individual (INDIV DISTR RELAY) ..................................................................... 63
Simrad - HH36 Installation and Operation Instructions6
Section 7 - Installation Instructions ................................................................64
7-1 Batteries and charger .................................................................................................................. 64
7-1-1 Installing the battery pack .....................................................................................................................64
7-1-2 Initial charge ...................................................................................................................................................64
7-1-3 GPS connector ...............................................................................................................................................65
7-1-4 Battery charger operation ......................................................................................................................66
7-1-5 Mounting battery charger to flat surface ..................................................................................... 66
7-1-6 Mounting battery charger and bracket onto wall ..................................................................66
7-2 Installing the belt clip ................................................................................................................... 67
7-3 Installing and removing the antenna ..................................................................................... 68
Appendix A - Technical specifications ............................................................69
Appendix B - US & ROW VHF Marine Channel Charts ..................................... 71
B-1 International Channel Chart ....................................................................................................... 71
Special Notes on International Channel Usage.......................................................................................72
B-2 USA Channel Chart ......................................................................................................................... 73
Special Notes on USA Channel Usage ..........................................................................................................74
B-3 CANADA Channel Chart ............................................................................................................... 75
Special Notes on Canada Channel Usage...................................................................................................76
B-4 US & Canada WEATHER Channels .............................................................................................77
B-5 EAS (Emergency Alert Systems) Alerts .................................................................................... 78
Appendix C - EU VHF Marine Channel Charts ................................................80
C-1 EU International Channel Chart................................................................................................. 80
Special Notes on EU International Channel Usage ...............................................................................81
C-2 Inland Waterways Country Specic table - ATIS ON ........................................................... 82
C-3 Special Channels ............................................................................................................................. 85
Countries of Intended use in the EU: .............................................................................................................85
Simrad - HH36 Installation and Operation Instructions 7
Safety and operational information
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
CAUTION: Changes or modications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
Industry Canada Statement
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Indus­try Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dé­passepas l’intensité nécessaire à l’établissement d’une communication satisfaisante.
This radio transmitter HH36 (IC:4697A-LINK2) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Le présent émetteur radio HH36 (IC:4697A-LINK2) a été approuvé par Industrie Canada pour fonctionner avec les types d’antenne énumérés ci-dessous et ayantun gain admis­sible maximal et l’impédance requise pour chaque type d’antenne. Les types d’antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l’exploitation de l’émetteur.
Antenna type: Flexible with SMA type connection supplied with the radio.
CE Compliance Statement
This product complies with CE under R&TTE directive 1999/5/EC. The relevant Declara­tion of Conformity is available in the following website under model documentation section: http://www.simrad-yachting.com.
Simrad - HH36 Installation and Operation Instructions8
Important
1. DSC functions will not operate until you have entered your user MMSI.
2. The radio channels installed into the radio may vary from country to country, depending upon the model and government or national communications authority regulations.
3. Simrad recommends that you check the radio operating licensing requirements of your country before using the radio. The operator is solely responsible for observing proper radio installation and usage practices.
4. This radio is designed to generate a digital maritime distress call to facilitate search and rescue. To be eective as a safety device, this radio must be used only within the geographic range of a shore-based VHF marine Channel 70 distress and safety watch system. The geographic range may vary but under normal conditions is approximately 20 nautical miles.
Safety Information
When transmitting, hold the radio in a vertical position with its microphone 2 inches (5 cm) away from your mouth and keep the antenna at least 2 inches (5 cm) away from your head and body.
The radio must be used with a maximum operating duty cycle not exceeding 50%, in typical Push-to Talk congurations.
DO NOT transmit for more than 50% of total radio use time (50% duty cycle). Transmitting more than 50% of the time can cause FCC RF exposure compliance requirements to be exceeded.
To maintain compliance with the Body Worn conguration use only supplied accessories.
Other body-worn accessories or congurations may not comply with the FCC RF exposure requirements and should be not be used.
The information listed above provides the user with the information needed to make him or her aware of RF exposure, and what to do to assure that this radio operates with the FCC RF exposure limits of this radio.
This Marine VHF radio also complies with the following guidelines and standards regarding RF energy and electromagnetic energy levels as well as evaluation of those levels for human exposure:
• FCC OET Bulletin 65 Edition 97-01 Supplement C, Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields.
• American National Standards Institute (C95.1-1992), IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz.
• American National Standards Institute (C95.3-1992), IEEE Recommended Practice for the Measurement of Potentially Hazardous Electromagnetic Fields — RF and Microwave.
Simrad - HH36 Installation and Operation Instructions 9
Section 1 - General information
Congratulations on your purchase of this handheld VHF marine radio HH36, designed and built using superior technology and craftsmanship. It provides the following useful features:
• Adjustable contrast settings for the LCD
• Adjustable keypad backlighting for easy night time use
• Waterproof and submersible to comply with JIS-7
• GPS latitude and longitude (LL) and time display
• Built-in GPS sensor
• Choice of High or Low (5 W or 1 W) transmission power
• Special CH16 key for quick access to the priority (international distress) channel
• Special 3CH key to select your three favorite channels
• Flexible dual watch facility
• DSC (Digital Selective Calling) capability that meets CLASS-D standards
• DISTRESS call button to automatically transmit the MMSI and position until an
acknowledgement is received
• Easy access to a buddy list of up to 20 favorite people
• LL position polling information
• Buddy tracking capacity
• Weather alert facility (US only)
• ATIS facility for inland waterways (Europe only).
CAUTION
Battery caution: This device uses a Lithion Ion battery - please observe the following cautions.
• Do not disassemble
• Do not incinerate or expose to re
• Dispose of used batteries according to local codes and requirements.
M
GO
MOB
HH36 MARINE VHF/GPS
CALL
MENU
WX
NAV
HI/LO
WATERPROOF
9
16
PHONE-PORTOP 03:00 UTC
36°45.193`S 174°42.486`E
3CH
SCAN
20
Simrad - HH36 Installation and Operation Instructions10
Section 2 - Controls and keys
Speaker
CALL/MENU
Mic
WX/NAV
HI/LO/GPS
Low battery indicator
Favorite channels:
1, 2 or 3
Speaker/Mic jack
Channel
Vol + and Vol -
GPS Antenna
Right Softkey
CH /
SQL /
PWR/LOCK/EXIT
Tx Power: HI or LO
GO/MOB
Status: T (transmit) or R (receive)
Signal strength
16/9 priority key
DISTRESS Key
PTT
VHF Antenna
Left Softkey
Working mode channel name
Time COG/SOG
Latitude
Longitude
Channel Bank
Center Softkey
(In DSC mode)
Simrad - HH36 Installation and Operation Instructions 11
2-1 Keys/Controls and functions
PWR/LOCK/EXIT PWR: To turn the unit on and o, press and hold down PWR /
/ EXIT (red key) for more than 2 seconds and release.
LOCK: The keylock, locks and unlocks keypad. Press PWR /
/ EXIT (red key) for 1 second and release. A key icon will
appear on screen to indicate whether keylock is on or o.
EXIT: Also used to EXIT some menu items while in DSC mode.
Short press PWR / / EXIT (red key) for 1 second and release.
VOL Volume Adjustment - located on the side of the radio. Press
to increase or press to decrease until a comfortable volume is reached.
SQL / Squelch or Threshold Level - located on the central control dial.
Sets the threshold level for the minimum receiver signal. 16 steps available.
CH / Channel select - located on the central control dial. Press to
select a higher channel or press to select a lower channel.
16/9 Priority Channel. Press to cancel all other modes (except for
when in DSC mode) and to tune into the priority channel. Press again to return to your original channel. To make Channel 09 the default instead, hold down 16/9 until a beep sounds and 09 is displayed (US only).
CH / Channel Select. The current channel is shown on the screen in
BIG digits with the channel description information below the channel number.
Press CH / to step through the available channels one at a
time, or hold down to scroll quickly through all the available channels. See Appendix B for a listing of channel charts.
Alphanumeric Entry. This key can also be used for menu
selection and alphanumeric entry. Press CH / to scroll the cursor up or down menu options when navigating menus.
When editing an item that contains only numbers, press - CH
to count through the numbers or hold down to scroll through quickly.
To enter a character, press CH to step through the alphabet or
hold down to scroll through quickly.
PTT Push To Talk. Push to start transmitting then talk into the mic.
Simrad - HH36 Installation and Operation Instructions12
HI/LO/ Transmission Power. High (HI) 5 W or Low (LO) 1 W. Press to
toggle between high or low transmission powers for the entire channel bank. The or selection is shown on the LCD screen.
Some channels allow only low power transmissions. Error beeps
will sound if the power transmission setting is incorrect.
Some channels allow only low power transmissions initially, but
can be changed to high power by holding down HI/LO and PTT all at the same time. See Appendix B for a complete listing of channel charts.
Hold down key to enter GPS Satellite mode.
WX/NAV WX. Quickly press to access Weather channels. Press again to
return to your previous mode.
For non US models: The Wx key can be programmed to a
weather channel of your choice. See section 4-7-9 to program your favorite channel.
NAV. Hold down WX/NAV for more than 3 seconds to enter
Navigation mode. Bearing, Distance and cross track error from the last selected waypoint will display on the screen. If no WP is set, it will appear “NO ACTIVE ROUTE!!” prompt.
GO/MOB Press GO/MOB if you are navigating to waypoint and want to
reset the XTE (cross track error) as shown on the screen.
If someone falls overboard, hold down GO/MOB for about 3
seconds to mark the position.
The latitude and longitude of the Man Overboard position is
shown on the screen and is automatically set as the destination waypoint.
CALL/MENU CALL. Quickly press the CALL/MENU key to access the DSC Call
menu. The call mode is used for making DSC calls.
MENU. Hold down the CALL/MENU key more than 3 seconds to
access the Menu Setup mode and to customize your VHF radio.
Simrad - HH36 Installation and Operation Instructions 13
2-1-1 Use of Softkeys in this radio
This radio utilizes ‘softkeys’ where the functionality of each softkey button will change depending on the mode the radio is in. The bottom line of the LCD display will indicate the function of each softkey located immediately below.
Left softkey (3CH/EXIT)
3CH softkey:
3CH
The 3CH softkey is used to initiate a Three Favorite Channels scan function. Press to toggle between your favorite channels. The , , or symbol appears on the LCD to show which favorite channel is selected.
If you want to scan all three favorite channels, press 3CH, then
immediately press and hold SCAN.
To add a favorite channel for the rst time, select that channel
then hold 3CH to store it in the CH1 location. Repeat the procedure to store two more favorite channels in the CH2 and CH3 locations respectively.
If you try and add another favorite channel it will overwrite the
existing CH3. CH1 and CH2 will remain unless you delete them.
To delete a favorite channel, select that channel then hold
down 3CH until a dialog box appears to prompt the deletion.
EXIT softkey:
EXIT
The EXIT softkey is used when navigating menus to clear incorrect entries, to exit from a menu without saving changes and to back up to the previous screen.
Right softkey (SCAN/ENTER)
SCAN softkey:
SCAN
The SCAN softkey is used to initiate a channel scan function. Quick press and release for Dual Watch - scan between your current channel and the priority channel in DUAL mode.
Press and hold down SCAN for more than 2 seconds to enter
ALL SCAN mode where the priority channel is checked every
1.5 seconds.
When a signal is received, scanning stops at that channel and
“R” appears on the screen. If the signal ceases for more than 5 seconds, the scan restarts.
In ALL SCAN mode, you may wish to ‘skip’ a channel because
it may alway be busy and therefore stops the scan. If you wish to ‘skip’ a channel, hold down the left softkey for more than 2 seconds.
SKIP
will appear on the screen and the channel
will be skipped. To cancel the skip, manually select the skipped
Simrad - HH36 Installation and Operation Instructions14
channel and press the left softkey for more than 2 seconds.
It is not possible to skip over the priority channel.
ENTER softkey:
ENTER
Use the ENTER softkey when navigating menus and to conrm entries and edits.
2-1-2 DSC Softkeys
UNABLE Left softkey. Respond to the call with unable to use the
requested channel.
ABLE Center softkey ( ). Press to ACK (acknowledge) a DSC call.
ACCEPT Right softkey. Press to ACCEPT a channel request. The radio will
immediately change to the requested channel.
NEW CH Right softkey. Press to request a new channel.
PAUSE Center softkey ( ). Press to pause a call when in repeat mode.
RESEND Left softkey. Press to resend the DSC call.
CANCEL Right softkey. Press to send the distress cancel call.
SILENC Left softkey. Provided as an option to silence an audible alarm.
Please refer to the following sections for more details.
Simrad - HH36 Installation and Operation Instructions 15
Section 3 - Operating the radio
3-1 Power On/Off
You can turn on the unit by pressing PWR/ /EXIT switch (on the top side of radio) until the screen and backlight are on. You can also adjust the volume to a comfortable level, by pressing the VOL / keys on the side of unit.
Note: Press the PWR/ /EXIT key at any time will turn the display backlight on.
3-2 Adjusting the Squelch level
The SQUELCH control enables you to set the levels of your desired signal. It determines how strong your signal can be before you can hear it, before it “breaks squelch.” It aims to keep any static, unwanted, weak or distant signals from interrupting your conversations.
There are 16 signals to choose from when adjusting the squelch level. To increase the levels, raise the “Squelch Gate” higher so that only stronger signals can get through. Level “0” for instance, means that there is no “Squelch Gate” and everything will get through.
To adjust the squelch level, press SQL / accordingly.
3-3 Volume control
Press VOL / to adjust the volume level. A volume sub-menu will appear when pressed. It times-out after 5 seconds.
3CH SCAN
3CH SCAN
Simrad - HH36 Installation and Operation Instructions16
3-4 Channel selection
To manually select a channel, press CH to increase, or press CH to decrease the chan­nel number. Communication channels are located on channel 01-28 and 60-88. For more detailed channel chart information, refer to Appendix B.
16/9 (Priority channel)
Press to cancel all other modes (except for when in DSC mode) and to tune into the prior­ity channel. Press again to return to your original channel. The default Priority Channel is CH16.
For US models: To make Channel 09 the priority channel, hold down 16/9 until a beep sounds and 09 is displayed.
3-5 Receiving and transmitting
CAUTION
Transmitting without an antenna may damage the radio.
1. To turn power on, press the PWR key for more than 2 seconds.
2. Adjust for comfortable volume level. ( The squelch level temporarily set to “0”).
3. Set the suitable Squelch level to mute noise if necessary.
4. Press CH / to select the desired channel.
5. When receiving a signal, appears on screen and audio is emitted from the speaker.
6. Further volume adjustment may be needed to get your desired setting.
7. Press HI/LO to select the output power.
8. Choose low power to conserve battery power, or choose high power for longer distance communications.
9. Press and hold “PTT” to transmit, then speak into the microphone, while appears on the screen.
10. Release PTT, to receive conversation. Note: Some channels are for low power only. Channel 70 cannot be used for transmission.
For clear and audible transmission:
• Pause for a few seconds after pressing PTT
• Hold the microphone 5 to 10 cm (2 to 4 inches) away from your mouth and speak at
a normal volume.
Simrad - HH36 Installation and Operation Instructions 17
3-6 Dual Watch operation
Dual watch monitors channel 16 while receiving another channel. To activate this, you must:
1. Select the desired operating channel (e.g. CH88).
2. Push the SCAN key repeatedly until appears on screen.
3. To cancel dual watch, press SCAN (once) until disappears.
If a signal is received on channel 16, dual watch pauses on channel 16 until the signal disappears.
To transmit on the selected channel during dual watch, press and hold PTT.
3-7 3CH operation (Favorite Channel)
You can instantly access the three most frequently used channels by 3CH mode, Three Fa­vorite Channels. Press to toggle between your favorite channels. The , , or symbols appear on the LCD to show which of your favorite channel is selected.
3-7-1 Add a favorite channel for the first time
1. Select the desired channel, then hold 3CH to store it. The CH1 symbol appears on the screen.
2. Repeat the procedure to store two more favorite channels in the CH2 and CH3 locations.
3-7-2 Modify or delete favorite channel
If you try and add another favorite channel it will overwrite the existing CH3. But CH1 and CH2 will remain unless you delete them.
To delete a favorite channel:
• Select that channel, then hold down 3CH until a dialog box appears to prompt the deletion.
Simrad - HH36 Installation and Operation Instructions18
3-8 Scan Operation
Scanning is an eective way to locate signals quickly over a wide frequency range.
All Scan
All channels in the set are scanned sequentially, in repeated cycles (CH16 is checked every
1.5 seconds).
01
02
03
16
04
88
3CH Scan
Press and hold down the SCAN key in the 3CH mode, you will then enter a 3CH SCAN mode. However, only the 3CH and CH16 will be scanned.
01
15
18
16
01
18
3-9 Navigation mode
Press and hold down NAV key to enter the Navigation Mode. It will display: Bearing, Distance and cross track error from the last selected waypoint.
If no WP is set, ‘NO ACTIVE ROUTE!!’ will appear to prompt you that no WP is selected, see the next section to select a Waypoint to navigate to.
During Nav Mode:
• PTT Return to normal mode and TX; release to return to Navigation mode
Simrad - HH36 Installation and Operation Instructions 19
• 16/9 Return to normal mode and go to 16/9
• NAV Return to normal mode
• GO Reset the cross track error (XTE)
• SQL Go to WP select Mode
• SQL Go to Plotter Mode
• Other key Error beep.
3-10 WP select mode
WP LIST 13
CAMP 1 MOB 1 CAMP 2 MOB 2 CAMP 3 MOB 3 DOCK 1 PARK 1 DOCK 2 PARK 2
EXIT
ENTER
• CH / Page up down the list
• SQL Go to Plotter Mode
• SQL Returns to Navigation Mode.
Note: During WP Select Mode, press ENTER right-key to ash the rst WP, then press CH / to select next WP, press ENTER right-key again to set the WP as your next
destination and enter navigation mode.
3-11 Plotter mode
During plotter mode:
• Softkey It will zoom in/out the circle to see more/less area
• SQL Go to Navigation Mode
• SQL Go to WP select Mode
Simrad - HH36 Installation and Operation Instructions20
• PTT Return to normal mode and TX
• 16/9 Return to normal mode and go to 16/9
• NAV Go to normal mode
• Other key Error beep.
To avoid screen clutter, a maximum of 5 waypoint icons closest to you plus the active waypoint are shown.
3-12 GPS satellite mode
Press and hold the HI/LO/ key to enter GPS satellite mode.
During GPS satellite mode:
• PTT Return to normal mode and TX
• 16/9 (16) Return to normal model and go to 16/9
• Return to normal mode
• Left softkey Return to normal mode
• Other key Error Beep.
Simrad - HH36 Installation and Operation Instructions 21
Section 4 - Advanced setup
How to display and navigate menus
1. Hold down CALL/MENU key for more than 1 second to enter the set up menu.
2. Press CH / to scroll up and down the menu until the cursor is positioned at the desired items. Press ENTER softkey to select the item.
3. Make any changes then press ENTER softkey to conrm changes. Otherwise, press EXIT softkey to ignore.
4. Press EXIT softkey to go back or exit. Any changes are activated as soon as you enter/exit the screen.
How to enter Alphanumeric data
Use the CH / key to enter characters.
1. Press to enter and count through numbers and letters, and hold down to select the desired character.
2. Press to go through letters of the alphabet, and hold down to select the desired character.
3. Press ENTER to conrm.
The following options are available through MENU:
• ATISMMSI
(EU only)
•ATISSELECT (EU only)
• WAYPOINT
• BACKLIGHT
• LAMP
• BUDDY LIST
• CONTRAST
• GPS/DATA
• RADIOSETUP
• DSC SETUP
• ATISSETUP
(EU only)
• GETBUDDY)
• TRACK LOG
• ERASE TRACK
• RESET
MENU
• MANUALL/L
• SETUP
• UIC (non EU)
• CHNAME
• RINGVOLUME
• KEY BEEP
• UNITS
• WATCHMODE
(US only)
• WXALERT(US only)
• NMEAOUT
• FAVCHSETUP
(non US)
• USER MMSI
• GROUP SETUP
• INDIV REPLY
• DSCSELECT
• LLREPLY
• AUTO SWITCH
• TESTREPLY
• TIMEOUT
Simrad - HH36 Installation and Operation Instructions22
Hold down the CALL/ MENU key for more than 1 second to enter radio set-up mode. This allows the following functions to be accessed. Scroll down the list and press ENTER. To exit the Menu or sub-menu modes press 16 or EXIT.
WAYPOINT Selects the WP List Entry to enter names and LL positions for a WP. Up to
500 WP can be stored.
BACKLIGHT Sets the backlight level: 8 levels.
LAMP Sets the backlight lamp time out.
BUDDY LIST Selects the Buddy List entry to enter names and MMSI’s for regularly
called DSC stations. Up to 20 names can be stored.
CONTRAST Selects display contrast setting: 8 levels.
GPS/DATA Select to change the GPS/DATA settings: TIME OFFSET, TIME FORMAT,
TIME DISPLY, LL DOSPLY, COG/SOG, GPS ALERT, GPS ENABLED, MAG VAR.
RADIO SETUP Select to change the radio settings: UIC, CH NAME, RING VOLUME, KEY
BEEP, UNITS, WATCH MODE, WX ALERT, NMEA OUT, FAV CH SETUP.
DSC SETUP Select to change the DSC settings: USER MMSI, GROUP SETUP, INDIV
REPLY, DSC SELECT, LL REPLY, AUTO SWITCH, TEST REPLY, TIMEOUT.
ATIS SETUP Select to change the ATIS settings: ATIS MMSI, ATIS SELECT (EU Only).
GET BUDDY Enable or disable Buddy Data and Auto Function.
TRACK LOG Set the distance interval for recording the track points.
ERASE TRACK Erase track history points.
RESET Reset to factory settings.
4-1 Waypoint
You can store up to 500 waypoints and their LL positions. When your WAYPOINT LIST is full, you cannot make a new entry until you have deleted an existing one.
• Each waypoint name can have a maximum of 6 alphanumeric characters
• The most recent waypoint name will be displayed at the top of your waypoint list.
4-1-1 Add a new waypoint
ENTER WP MOOR 1 12°32.233N 132°45.651’W
WP LIST NEW WP FISH1
ENTER WP
_ _ _ _ __ _ _ _° _ . _ _ _’ N _ _° _ . _ _
ENTER WP
MOOR 1
_° _ . _ _ _N _ _° _ . _ _ _W
Simrad - HH36 Installation and Operation Instructions 23
SAVE MOOR 1 YES NO
1. Select WAYPOINT and press ENTER.
2. Select WP LIST, and then NEW WP.
3. Use the CH / to enter the new waypoint name, one alphanumeric character at a time. Select one waypoint symbol (there are 20 icons available); and then press ENTER until the cursor moves to the latitude line.
4. Use the CH / to enter the latitude of the waypoint, one number at a time; then press ENTER. The cursor moves to the longitude.
5. Use the CH / to enter the longitude waypoint, one number at a time, then press ENTER.
6. A new screen appears automatically to show the new waypoint details. If they are correct, press ENTER to STORE the new waypoint. (If they are not correct, select EXIT).
4-1-2 Edit a waypoint
WP EDIT FISH 2 12°32.233N 132°45.651’W
MENU SELECT WAYPOINT BACKLIGHT LAMP
WAYPOINT
WP LIST
WP LIST NEW WP FISH 1 FISH 2
WP EDIT MOOR 1 12°32.233N 132°45.651’W
SAVE MOOR1 YES NO
1. Select WAYPOINT and press ENTER.
2. Select WP LIST, then push ENTER, the cursor is at new WP. Scroll down to the waypoint you want to edit then push ENTER.
3. Select WP EDIT and press ENTER.
4. The waypoint details are displayed and the cursor is positioned at the rst character of the name.
5. Use the CH / to change the rst character of the waypoint name then press ENTER, or just press ENTER to skip to the next character.
Simrad - HH36 Installation and Operation Instructions24
When you reach the last character of the waypoint name, make any changes if necessary, then press ENTER to move the cursor to the waypoint icon.
Note: If you do not want to change the waypoint name waypoint icon, press ENTER repeatedly until the cursor moves to the latitude.
To change the waypoint icon, use the CH / to change the icon or press ENTER to skip to latitude. To change latitude, use the CH / to change the rst digit or press ENTER to skip to the next digit. Repeat if necessary. When you reach the last digit, push ENTER to move the cursor to longitude.
Note: If you do not want to change the latitude, press ENTER repeatedly until the cursor moves to the longitude.
1. Repeat the previous step to change or press ENTER to continue.
2. A new screen appears. Press ENTER if you want to STORE the new waypoint. If you want to keep the original entry, move the cursor to NO then press ENTER.
4-1-3 Delete a waypoint
FISH 2 GO WP EDIT DELETE
MENU SELECT WAYPOINT BACKLIGHT LAMP
WAYPOINT WP LIST NEAREST WP TEMP
WP LIST NEW WP FISH 1 FISH 2
DELETE FISH 2 YES NO
WP LIST NEW WP FISH 1 HOME
1. Select WAYPOINT and press ENTER.
2. Select WP LIST and press ENTER. The cursor is at NEW WP, scroll down to the waypoint you want to delete, then press ENTER.
3. The cursor is at GO. Move the cursor to delete and push ENTER.
4. The waypoint is deleted immediately and the revised waypoint list is displayed.
4-1-4 Set a route to a stored waypoint
HOME GO WP EDIT DELETE
MENU SELECT WAYPOINT BACKLIGHT LAMP
WAYPOINT WP LIST NEAREST WP TEMP
WP LIST NEW WP FISH 1 HOME
Simrad - HH36 Installation and Operation Instructions 25
GO HOME YES NO
1. Select WAYPOINT and press ENTER.
2. The cursor is at WP LIST, press ENTER. The cursor is at NEW WP, scroll down to the waypoint to use as the route then press ENTER.
3. The cursor is at GO, push ENTER and enter the navigation mode. The waypoint is set as your next destination.
4-2 Backlight adjustment
1. Select BACKLIGHT and press ENTER. There are 8 backlight levels.
2. SQ / to adjust the setting. Press ENTER to conrm the setting and return to the MENU SELECT.
MENU SELECT WAYPOINT BACKLIGHT LAMP
BACKLIGHT
■ ■ ■ ■
LO HI
4-3 Lamp timer
1. Select LAMP and press ENTER. There are 4 timer settings: Always on, 5s, 15s, 30s (default).
2. Press CH / to adjust the setting. Press ENTER to conrm the setting and return to the MENU SELECT.
MENU SELECT WAYPOINT BACKLIGHT LAMP
LAMP TIMEOUT ALWAYS ON 5 SECOND 15 SECOND
Simrad - HH36 Installation and Operation Instructions26
4-4 Buddy list (Manage your buddy list)
You can use the buddy list to store names and associated MMSIs of 20 DSC stations that you call frequently. Buddy names are stored in the order of entry, with the most recent entry rst.
The following sections demonstrates how to use BUDDY LIST, these include: to add, edit, and delete entries.
4-4-1 Add a new buddy name
You can enter up to 20 buddy names. When your BUDDY LIST is full, you cannot make a new entry until you have deleted an existing entry.
• Each buddy name can have a maximum of 6 alphanumeric characters
• The most recent buddy name entered is shown at the top of your buddy list.
ENTER NAME STARFISH 2 ENTER MMSI
_ _ _ _ _ _ _ _ _
MENU SELECT LAMP BUDDY LIST CONTRAST
BUDDY LIST MANUAL NEW
ENTER NAME
_ _ _ _ _ _ _ _ _
ENTER MMSI
_ _ _ _ _ _ _ _ _
MANUAL NEW STARFISH 2 SEA ROSE MERMAID
ENTER NAME STARFISH 2 ENTER MMSI
0 _ _ _ _ _ _ _
ENTER NAME STARFISH 2 ENTER MMSI 123456789
STARFISH 2 123456789 STORE CANCEL
1. Select BUDDY LIST and press ENTER.
2. The cursor is at <MANUAL>. Push ENTER.
3. Use the CH / to enter the new buddy name one character at a time. Then press ENTER until the cursor moves to the MMSI entry line.
4. Use CH / to enter the 9-digit MMSI that is associated with that buddy name, one number at a time, then press ENTER.
5. After you enter the last digit of the MMSI, a new screen appears automatically to show the new buddy name and MMSI. Check that it is correct; and then push ENTER to save the new entry. (If it is not correct, select EXIT).
Loading...
+ 60 hidden pages