SIM2 Lumis UNO User Manual
SIM2 Multimedia
LUMISUNOE
User Guide
Contents
3 Important information
About this User Guide
Safety
3D content
Environment
Notice
7 Chapter 1: Introduction
Key Features and Benefits
System Components
Optional Accessories
9 Chapter 2: Overview
Remote Control
Projector Keypad
Connections
3D RF Emitter
3D Glasses
13 Chapter 3: Installation
Location
Mounting
Connections
Switching On and Off
19 Chapter 4: Operation
Viewing 3D Content
3D Menu
Input Menu
Main Menu
Picture
Image
Setup
Menu
Memories
Info
Quick Menus
Messages
35 Chapter 5: Troubleshooting
37 Chapter 6: Specifications
39 Chapter 7: Projection Distances
40 Chapter 8: Dimensions
LUMISUNOE
User Guide
2
Important information
About this User Guide
Information contained in this User Guide may be updated from time to time due to
product improvements and customer feedback. Visit www.sim2.com to find the latest
version of this document.
This document contains proprietary information protected by copyright. All rights are
reserved.
All trademarks and registered trademarks are the property of their respective owners.
Safety
To reduce the risk of electrocution, disconnect the power cord on the
rear panel before removing the top cover of the projector. For technical
service refer to trained personnel authorized by the manufacturer.
If the lamp suddenly explodes with a loud bang, turn off the projector immediately
and air the room thoroughly. Do not attempt to restart the projector and do attempt
to replace the bulb: contact your local service center.
Read this manual
Read all chapters of this manual carefully before switching on the projector. This
manual provides basic instructions for operating the LUMISUNOE projector.
Installation, preliminary adjustments and procedures that necessitate the removal of
the top cover and contact with electrical components must be performed by
authorized, trained technicians. To ensure safe operation and long term reliability use
only the power cords supplied by the manufacturer. Observe all warnings and precautions. Keep the manual for future consultation.
Do not touch internal parts of the projector
Inside the housing there are electrical parts carrying dangerously high voltages and
parts operating at high temperature. Never open the housing. Entrust all servicing and
repair work to a SIM2 Authorized Service Center. Opening the housing voids the
warranty.
Disconnect the appliance from the power supply
The device that disconnects the projector from the mains is the power plug. Ensure
that the power cord plugs and the electrical outlets are easily accessible during
installation operations. Pull the plug, not the cord, to disconnect the projector from
the mains. Use only the specified power supply. Connect the projector to a mains
electrical supply with rated voltage of between 100-240 V AC, 50/60 Hz and equipped
with a protective earth connection. If you are not sure of your domestic mains rating,
contact an electrician. Take care to avoid overloading the power socket and any
extension leads.
Important information LUMISUNOE
User Guide
3
Switching the projector off
Pay attention to the switch off procedure for the projector. The projector must always
be brought back to the standby state to allow the projector to carry out the cooling
procedure. Should this not happen, for example due to a power cut, the projector may
enter a state of protection that leads to switch-on being blocked. This block will last
until the internal components of the projector have completely cooled down.
Changing the fuses
Before changing the fuse, disconnect the projector from the mains power supply. The
fuse compartment is next to the power supply connector. Remove the fuse holder
with a flat head screwdriver and replace the fuse. Fit the replacement fuse. Use only
type T 10 A L H fuses for the projector.
Be careful with cables
Make sure cables are routed so that people are not impeded or become a trip hazard.
Keep all cables away from children. Install the projector as close to the wall socket as
possible. Avoid stepping on power cords, make certain they do not become tangled,
and never jerk or tug them; do not expose them to sources of heat, and make sure
they do not become knotted or crimped. If the power cords become damaged, stop
using the projector and request the assistance of an authorized technician.
Disconnect the projector from the mains power during electrical storms and when
not in use
To prevent damage from lightning strikes in the vicinity, disconnect the projector
during storms or when the projector is going to be left unused for a long time.
Avoid contact with liquids and exposure to damp
Do not use the projector near water (sinks, tubs and so on); do not place objects
containing liquids on or near the projector and do not expose it to rain, humidity,
drops of water or sprays; do not use water or liquid detergent to clean it.
Place the projector on a stable surface
Place the projector on a stable surface or use a suitable ceiling mounting bracket.
Never place the projector on its side or rear, on the lens or top panel.
Do not allow the projector to overheat
To prevent overheating, allow a free space of at least 0.25 m (10 in.) on the left, right
and rear sides of the projector. Do not obstruct the ventilation slots. Do not place the
projector near heat sources such as heaters, radiators or other devices (including
amplifiers) that generate heat. Do not place the projector in an area where there is
insufficient space (shelving units, bookshelves and so on) and in general avoid placing
it in poorly ventilated areas as this may prevent sufficient cooling and significantly
reduce lamp life.
Never look directly at the projection lamp
Never look directly into the lens when the lamp is on as the intense light may damage
your eyes. Take particular care that children cannot do so.
Take special care regarding movement of the lens
Do not place objects in the slots on the side of the lens and also ensure that vertical
lens movements are not impeded by external objects.
Important information LUMISUNOE
User Guide
4
Do not insert objects through the openings in the projector
Make sure that no objects are inserted inside the projector. If this should occur,
disconnect the projector from the power supply immediately and call an authorized
technician.
Power saving
We advise disconnecting the projector from the power supply when not in use. In this
way you will achieve considerable power savings while at the same time protecting
internal electrical parts from wear.
3D content
Discomfort (such as eye strain, headaches, motion sickness, nausea, dizziness, disorientation) may be experienced while watching 3D content. In this case, stop watching
and consult a doctor if symptoms are severe.
Consult a doctor before allowing young children (especially those under six years old)
to watch 3D content as their visual system is still under development.
Monitor children (including teenagers) watching 3D content, as they are more at risk
of experiencing discomfort and less inclined to report symptoms.
Individuals who may be susceptible to epileptic seizures or strokes (on the basis of
personal and family history) should consult a doctor before watching 3D content.
All viewers should take regular breaks from watching 3D content. Length and frequency of these breaks may vary from person to person.
Environment
This product contains materials derived from natural resources during its
manufacture. It may contain materials that constitute a health and environmental
hazard. To prevent harmful materials from being released into the environment and to
promote the use of natural materials, SIM2 provides the following information
regarding the disposal and recycling of the product.
Waste electrical and electronic materials (WEEE) should never be disposed of in
normal urban waste disposal facilities.
Observe the following instructions:
• When you no longer wish to use your electrical and electronic equipment,
• You may return your old equipment to your SIM2 Authorized Dealer free of
• If you need more information regarding recycling, reuse and product
The label on the product, shown here, indicating a canceled garbage can,
is intended to remind you that the product requires special handling at
the end of its service life. Materials such as glass, plastic and some
chemical compounds are recoverable and can be recycled for reuse.
take it to your local waste disposal facility for recycling.
charge when you buy a new product that is equivalent or has the same
functions as the old one. Contact SIM2 to find your local dealer.
exchanges, contact SIM2 customer service.
Important information LUMISUNOE
User Guide
5
Notice
Lastly we suggest further measures to safeguard the environment, such as recycling of
internal and external packaging (including that used for shipping) in which the product
was delivered. With your help, we can reduce the amount of environmental resources
required to make electric and electronic equipment, reduce the use of waste tips for
used equipment and, in general, improve our quality of life by making sure that
hazardous materials are correctly scrapped. Incorrect treatment of the product at the
end of its service life and failure to follow the above disposal instructions are
punishable under local legislation.
Product disposal
The lamp inside this projector contains mercury and may be subject to
special disposal or recycle regulations. Dispose or recycle in accordance
with local laws. For more information contact the Electronic Industries
Alliance at www.eiae.org or check www.lamprecycle.org
The appliance has been subjected to exhaustive operating tests by SIM2 to guarantee
the highest quality. The projector bulb life should thus initially be around 30-60 hours.
In addition to the customary checks, the Quality Control department also runs additional statistical tests before shipment. In such cases, the packaging may show signs of
having been opened, and the hours of lamp operation may prove to be higher than
those normally shown when only standard tests are performed.
As the optical system of the LUMISUNOE is extremely compact and has the purpose of
developing very high brightness and contrast, it is possible that a small quantity of
light is visible outside of the projection area and will vary depending on the type of
lens used and the zoom and shift setup. This characteristic of the optical system is to
be deemed as normal. In order to reduce this effect SIM2 recommends that the area
surrounding the projection screen is as dark as possible.
The LUMISUNOE is a three chip DLP projector and uses three high resolution DMD
(red, green, blue). These three DMD are precisely aligned through a high precision
process that reduces the alignment error to within the foreseen limits of tolerance.
The maximum limits of misalignment are the following:
• Screen Center: up to 0.7 pixels between each color
• Screen Borders: up to 2 pixels between each color
These limits are perfectly normal for this optical system and will not be considered as
a malfunction of the product.
Note: One pixel corresponds to 10 thousandths of a millimeter on the DMD.
Important information LUMISUNOE
User Guide
6
1 Introduction
The LUMISUNOE is a high-end compact 3-chip DLP 3D single unit projector that
utilizes SIM2’s state-of-the-art optical technologies to produce images with
exceptional black level and contrast performance.
The LUMISUNOE is able to emulate the best 3D cinema projection systems, in terms of
color fidelity, definition and depth of image. These are all conveyed accurately, as is
the fluid motion of fast-action movies and sports. This all adds up to an incredible 3D
experience at home.
The LUMISUNOE is designed for use with large screen sizes – up to 5 m (16.5 ft.) wide.
A choice of three high quality glass lenses (T1, T2 and T3) is available, giving the
projector a total throw ratio of 1.37-3.90:1.
To aid calibration SIM2’s Live Color Calibration software enables complete control
over:
• primary, secondary and white point color coordinates
• gamma tables
allowing calibration experts to accurately calibrate the final image via a user-friendly
application for Windows-based computers.
Key Features and Benefits
• high picture quality: SIM2 renown image processing and the latest 0.95 in.
1080p DarkChip4 DMD from Texas Instruments
• precision optics: SIM2 ALPHAPATH light engine
• high brightness: 3-chip DLP projector
• artifact-free fast-action images: SIM2 PureMotion processing
• high resolution: actual full HD 3D images, without blur and ghosting
• comfortable 3D viewing: high brightness ghost-free sharp images
• immersive 3D effect: large screen sizes thanks to high brightness images
• 3D wide viewing angle: stereo separation independent from viewing angles
• screen flexibility: no constraints in the choice of the screen material
• compatibility: no need of dedicated sources and preprocessing for 3D viewing
• longer lamp life: affordable and reliable P-VIP lamps
System Components
Your LUMISUNOE DLP projector ships with the following items:
• 1 x backlit remote control unit (with four AAA/LR03 batteries)
• 1 x SIM2 3D sync RF emitter (ADE025-RF-S1)
• 4 x pairs of SIM2 X105-RF-S1 active shutter glasses
• 3 x AC power cords (US, EU and UK), 2 m (6.6 ft.) long
• 3 x jacks for 12 V output connectors
• 1 x 4.0-millimeter Hex wrench (for lens shift adjustment)
• 1 x User guide (this document)
1 Introduction LUMISUNOE
User Guide
7
If any items are missing or damaged, contact your SIM2 Authorized Dealer as soon as
possible. Keep the original packaging in case anything has to be shipped.
Optional Accessories
• Projector ceiling bracket (LUMISBRKT)
• PANAMORPH Anamorphic lens systems (static or motorized)
• ISCO Anamorphic lens systems (static or motorized)
• VISUSRF-BOX (8 SIM2 Visus 3D RF glasses)
• VISUSRF-SYSTEM (7 SIM2 Visus 3D RF glasses and 1 RF emitter for SIM2 Visus
3D RF glasses)
• VISUSRF-SYSTEM-ACC (4 SIM2 Visus 3D RF glasses and 1 RF emitter for SIM2
Visus 3D RF glasses)
1 Introduction LUMISUNOE
User Guide
8
2 Overview
Remote Control
Turn backlight on for about 5
seconds
turns the projector off
1-9
0
●
ESC exits OSD
▴
◂ ▸
▾
MENU
+ / -
II 3D enters 3D menu
F1, F2
select inputs and turn the projector
on
enters OSD Input menu and turns
the projector on
OK enters submenus, confirms
actions
select menu items, adjust settings or
cycle through the test patterns
enter OSD Main menu and select
the desired section, each press of
the key selects the next tab in the
menu
Memory enters Memories menu
perform user-defined actions
(default assignments are: F1 = Zoom,
F2 = Focus)
Info displays projector Info
A Auto performs Auto Adjustment
Aspect enters Aspect Quick menu
Not used
Custom Remotes
You can use your own IR remote control to control your LUMISUNOE projector.
• If you are using a remote control with learning capabilities, use the projector
remote control to teach the commands to your remote.
• If you are using a programmable remote control, the setup software probably
allows importing of Pronto Hex codes. See SIM2 L LUMISUNOE IR Control for a
list of all the projector codes in Pronto Hex format, including a number of
discrete codes for:
◦ Aspects
2 Overview LUMISUNOE
User Guide
9
◦ Memories
◦ 3D Controls (3D Mode and Input Formats)
Operation
The LUMISUNOE projector has two IR receivers, one on the front and one on the back
of the unit. The operative range of the remote control is approximately 10 m (33 ft.).
Make sure that there is nothing obstructing the infrared beam between the remote
control and the IR receiver you are pointing to. You can point the remote control
towards the screen, as the IR beam is reflected by the screen towards front IR receiver
of the projector. In this case the effective range of the remote control may be smaller
than declared.
Batteries
To install batteries in the remote control:
1. Open the battery cover.
2. Insert four AAA (LR03) batteries making sure the polarities match the + marks
inside the battery compartment.
3. Replace the cover.
Replace the batteries with new ones when the operating range of the remote control
decreases. Dispose of used batteries according to local regulations. Make sure you do
not mix old and new batteries or different types of batteries.
Warning: If you will not use the remote control for a long time, remove the batteries
to avoid battery leakage.
Projector Keypad
turns the projector on or off
◂ ▸ ▴ ▾
MENU enters OSD Main menu and selects the desired section
ESC exits OSD
SOURCE/O enters OSD Input menu/selects a menu item
select menu items, adjust settings or switch test patterns
2 Overview LUMISUNOE
User Guide
10
Connections
❶ ❷ ❸ ❹ ❺ ❻
❼ ❽
Inputs
Control/
Service
Outputs
❶
HDMI 1
Accept both HDMI and DVI digital video inputs.
HDMI 2
❷
Components/RGB-HV Four RCA connectors. They accept both standard
and high-definition component (YPrPb) and
RGB-HV signals. Also used as RGB input for SCART
RGBS signals.
❸
Video One RCA connector. Accepts composite video
signals. Also used as composite sync input for
SCART RGBS signals.
❹
Graphics RGB One D-Sub 15-pin female connector. Accepts
component or RGB high-definition signals.
❺
USB USB 1.1 (type B) port for serial commands and
firmware upgrade.
❻
RS-232 RS232 (female D-Sub 9-pin) port for serial
commands and firmware upgrade.
❼
TRIG 1 12 V 100 mA max output, for motorized screen
control. Activates when the projector is switched
on.
TRIG 2 12 V 100 mA max output, for motorized screen
masking systems control. See “Screen” on page
27.
TRIG 3 12 V 100 mA max output, for motorized
anamorphic lens position control. See
“Anamorphic Lens” on page 27.
❽
3D Sync OUT VESA DIN-3 connector for 3D RF Emitter cable.
2 Overview LUMISUNOE
User Guide
11
3D RF Emitter
The 3D RF emitter is designed to be placed near the projector and aimed at the
screen. It receives the 3D sync signal from the projector and emits RF pulses that
reach the 3D glasses RF receiver.
The emitter does not require a battery.
Note: The emitter emits sync pulses only when the projector displays 3D content.
3D Glasses
When displaying 3D content, the projector alternately displays one image for the left
eye and one image for the right eye in rapid succession. The 3D glasses turn on and off
their lenses, in sync with the projector, so that each eye receives exactly the image
intended for it. The sync is possible thanks to the RF pulses received by the glasses
from the 3D RF emitter.
❶ Button Button for ON and OFF
❷ LED Indicating glasses status
❸ Micro USB port To charge the glasses
❹ Lens Liquid crystal shutter
❺ RF Receiver Receive RF signals from 3D Emitter
2 Overview LUMISUNOE
User Guide
12
3 Installation
This section provides instructions for the installation of the LUMISUNOE projector.
Important: Installation procedures should be performed by a qualified AV system
specialist.
Location
When installing the LUMISUNOE projector, take the following considerations into
account.
Installation Type
Select the installation type that best suits your needs:
• front or rear projection
• floor or ceiling mount
Lens Type
Choose the desired distance from the screen and select the lens type (T1, T2 or T3)
that determines the desired screen size.
Cooling
Make sure that the planned location for the projector has adequate ventilation. Check
that room temperature is below 35° C and that the projector is away from heating
vents. Ensure a minimum 0.25 m (10 in.) clearance on the left, right and rear sides of
the projector.
Power Outlets
Verify that the powers outlets are grounded and preferably shielded from power
surges and fluctuations. A UPS is optional. LUMISUNOE power supply operates on any
nominal line voltage between 100-240 V AC, 50-60 Hz.
Cables
Check planned cable lengths for video and control cables and make sure these lengths
do not exceed specifications.
Ambient Light
Avoid or minimize light sources directed at the screen to preserve the quality of the
projected image.
Mounting
The projector can be Floor mounted (upright) or Ceiling mounted (inverted). Choose
the method that best suits your installation.
Important: The projection lens is not centered to the chassis (it is off-center
horizontally by 75 mm or 2.95 in., see “Dimensions” on page 40 for details). Make sure
the centerline of the lens is centered horizontally to the center of the screen.
Floor Mounting
Position the projector on a secure and flat surface (such as a table or a shelf). Adjust
the three feet at the bottom of the projector until the projector is level on all sides.
3 Installation LUMISUNOE
User Guide
13
Loading...