Page 1
168754
Y
e
a
r
G
u
a
r
a
n
t
e
e
3
3
R
E
G
I
S
T
E
R
O
N
L
I
N
E
*
GB
ESP
F
GB
ESP
I
F
GB
D
ESP
NL
I
ESP
ESP
I
ESP
NL
I
POWER
S
I
L
V
E
R
L
I
N
E
R
A
N
G
E
Inverter
Inverter
Convertidor
1000W
Convertisseurs
Wechselrichter
www.silverlinetools.com
Inverter
Omvormer
Page 2
POWER
S
I
L
V
E
R
L
I
N
E
R
A
N
G
E
1
3
2
4
2
5
6
Page 3
GB
Explanation of Symbols
• Wear breathing protection.
• Wear eye protection.
• Wear hearing protection.
• Wear gloves.
• Do not dispose as unsorted waste.
• Risk of electrocution
Specification
Input voltage range ..............................12V DC
Output voltage ......................................230V
Output frequency..................................50Hz
Waveform .............................................Modied sine
Max continuous output power ..............1000W
Surge capacity/time .............................2000W for one second
Efciency .............................................>90%
No load current draw ...........................<0.6A
Low voltage shutdown .........................10V
As part of our ongoing product development, specications of
Silverline products may alter without notice.
General Safety
Carefully read and understand this manual and any label attached to
the tool before use. Keep these instructions with the product for future
reference. Ensure all persons who use this product are fully acquainted
with this manual.
Even when used as prescribed it is not possible to eliminate all residual risk
factors. Use with caution. If you are at all unsure of the correct and safe
manner in which to use this tool, do not attempt to use it.
Keep guards in position
Always keep guards in position, in good working order, correctly adjusted •
and aligned. Never attempt to use a tool if any of the supplied guards are
missing. If any guards are damaged, replace before use.
Remove adjusting keys
Always check to see that keys and adjusting devices are removed from •
the tool before use.
Clean the work area
Accidents can occur where benches and work areas are cluttered or •
dirty, oors must be kept clear, avoid working where the oor is slippery.
If working outdoors, make yourself aware of all potential slip and trip
hazards before using this tool.
Children and pets
Children and pets should always be kept at a safe distance from your •
work area. Lock tools away where children can’t get access to them. Do
not allow children, or untrained persons to use this tool.
Use the correct tool
Don’t force, or attempt to use a tool for a purpose it was not designed. •
This tool is not intended for industrial use.•
Wear suitable clothing and footwear
Don’t wear loose tting clothing, neckties, jewellery, or other items which •
may become caught. Wear non slip footwear, or footwear with protective
toe caps where appropriate. Long hair should be covered or tied back.
Keep your balance
Don’t over reach, keep proper footing at all times, do not use tools when •
standing on an unstable surface.
Accessories
The use of any attachment or accessory other than those mentioned •
in this manual could result in damage or injury. The use of improper
accessories could be dangerous, and may invalidate your warranty.
Secure work
Where possible, always secure work. If appropriate use a clamp or vice, it •
will allow you to use both hands to operate your tool.
Check for damaged or missing parts
Before each use, check if any part of the tool is damaged or missing, •
check carefully that it will operate properly and perform its intended
function. Check alignment of moving parts for binding. Any guard or other
part that is damaged should be immediately repaired or replaced by an
authorised service centre. DO NOT USE IF DEFECTIVE.
4
Page 4
168754
Inverter
Electrical Safety
The wires in this product are coloured:
Blue Neutral
Brown Live
Green & Yellow Earth
This appliance must be protected by a suitable fuse.•
To prevent re or shock hazard, do not expose this product to rain, water •
or moisture.
There are no user serviceable parts inside except those referred to in •
this manual.
Always refer servicing to qualied service personnel. Never remove any •
part of the casing unless qualied to do so; this unit contains dangerous
voltages.
Use of a residual current device will reduce the risk of electric shock.•
Dangerous environment
Do not use power tools in damp or wet conditions, or expose them to •
rain. Provide adequate surrounding work space and keep area well lit.
Do not use power tools where there is a risk of explosion or re from
combustible material, ammable liquids, ammable gases, or dust of
an explosive nature. When using power tools avoid contact with any
earthed items such as pipes, radiators, cookers, refrigerators, metal
baths and taps.
Protect yourself from vibration
Hand held power tools may produce vibration. Vibration can cause •
disease. Gloves to keep the operator warm may help to maintain good
blood circulation in the ngers. Hand held tools should not be used for
long periods without a break.
Maintain your power tool
Ensure all ventilation holes are kept clear at all times. Overheating and •
re may otherwise result.
Always Disconnect
Before changing ttings or accessories, always ensure that your tool is •
disconnected from the power source.
Switch off before connecting
Ensure that the power tool is switched off before connecting to the power •
source. If the power tool stops unexpectedly, turn the power switch to off.
Do not abuse the power cord
Be sure your cable or extension cable is in good condition. Always have •
a damaged cable or extension cable replaced at an authorised service
centre before using it. Never yank or pull the cable to disconnect it from
the power socket. Never carry your tool by its cable. Keep the cable away
from damp, heat, oil, solvents, and sharp edges.
Don’t leave the tool running unattended
Always wait until your tool has completely stopped functioning, and has •
been unplugged, before leaving it.
Product Familiarisation
1 Power indicator light
2 Low battery indicator light
3 230V output socket
4 Power switch
5 12V input connectors
6 12V supply leads
Unpacking Your Inverter
Carefully unpack and inspect your inverter. Fully familiarise yourself with •
all features and functions of the product.
If any parts are damaged or missing, have these parts repaired or •
replaced before use.
Placement of your inverter
• Always place the inverter on a level surface.
• Do not use the inverter in any damp environment, or any position where
the inverter could accidentally come into contact with water.
• Always position the inverter away from direct sunlight and other
heat sources. The inverter should only be used when the ambient air
temperature is between 10-30˚C.
• Allow for adequate ventilation around the inverter. There should always
be at least 25mm of clear space around the inverter. Do not place
anything on top of the inverter. Ensure that ventilation holes are not
obscured.
• Do not use the inverter in any location where ammable gases may be
present. This includes inside engine bays, and battery compartments.
Connecting to the power supply
• This inverter is supplied with a 12V supply lead (6). This allows you to
connect the inverter directly to a 12V battery.
• Do not attempt to connect the inverter to any form of 230V distribution
system (e.g. building or caravan wiring).
• The 12V system must be capable of supplying an adequate current
to the inverter. To calculate the approximate current requirement, divide
the inverter power rating (W) by 10. Consult the vehicle user manual for
electrical supply information.
• This inverter should only be used with 12V DC positive earth electrical
systems. Use with any other type of system may be dangerous and could
cause permanent damage to electrical components.
• This inverter is equipped with dual 12V input connectors. This enables
two batteries to be used to feed the inverter. The inverter can be run from
one battery, but battery life will be reduced, and the inverter may shut
down under high load.
• Remove the screws of the 12V input connecters (5) and attach one end
of each 12V supply lead to the connectors. Tighten the screws. Ensure
that the positive and negative (red and black) leads are connected to the
correct terminals as indicated on the inverter
• The free ends of the 12V supply leads can now be connected to the
battery.
• To reduce the risk of accidental short circuiting, always have the
12V supply leads securely attached to the inverter when connecting or
disconnecting the battery.
• Do not attempt to connect the inverter to the 12V supply by any other
means than the supplied connector.
www.silverlinetools.com
5
Page 5
GB
Operating Instructions
Connecting a load
• Before connecting any appliance to the inverter, switch power switch (3)
to the ON position. After a few moments the green power indicator light
(1) will illuminate. The inverter is now ready to be used.
• Do not connect loads greater than the rated maximum continuous power
output of the inverter (see specications).
• Some appliances (televisions, stereos, motors, neon lights etc) may
require a much higher starting power than their rated power. If the
appliance will not start, the maximum output of the inverter has been
exceeded. Reduce the total load on the inverter.
• If the appliance to be connected does not have its wattage (W) indicated
on it, the wattage can be calculated by multiplying the amperage (A)
by 230.
• Electrical appliances can be connected to the 230V outlet sockets (3).
Low battery protection
• In order to prevent your vehicle battery from being run at, this inverter is
equipped with a low voltage alarm and automatic low battery shutdown.
• Do not connect loads greater than the rated maximum continuous power
output of the inverter (see specications).
• If the supply voltage drops to 10.5V the low battery alarm will sound
and the low battery indicator light (2) will illuminate. This indicates that
the battery should be charged. If the supply voltage is allowed to drop to
10V, the inverter will automatically cut out. To restart the inverter, switch
off, charge the battery, and switch back on.
• A typical 12V battery will have an operating time of at least 1-2 hours.
It is recommended that the vehicle’s engine is started and run once every
hour to “top up” the battery.
Note: the inverter may shut down as the engine is started due to the
high electrical load generated by the vehicle starter motor.
Overload protection
• This inverter is equipped with an in-built high temperature cut out. If
an overload causes the internal parts of the inverter to overheat it will
automatically shut down.
To restart, switch off, reduce the load, allow the inverter to cool, and •
switch back on.
Maintenance
Cleaning
Disconnect the inverter from the power supply before cleaning.•
Keep your inverter clean. Always clean dust or particles away, and never •
allow ventilation holes to become blocked. Use a soft brush, or dry cloth
to clean the inverter, if available blow through the ventilation holes with
clean, dry, compressed air.
Inverter will not operate
Electrical appliance will not
operate
Low voltage alarm on
continuously
Low output voltage
Television/stereo interference
6
Trouble shooting
Problem Possible cause Suggested Remedy
Low battery voltage
Inverter in thermal shutdown
12V lead not properly connected
Internal fuse “blown”
Starting load of appliance is too great Reduce load
Poor electrical connections
Inadequate power supply
Inverter is overloaded
Input voltage is below 11V
Inverter is located to close to aerial
Aerial cable is not shielded
Charge or replace battery
Allow inverter to cool before switching on
Check lead for proper connections
Have inverter serviced at an authorised service centre
Check/clean electrical connections
Check 12V system capacity
Reduce load
Charge or replace battery
Move inverter/aerial
Use shielded cable
Page 6
Silverline Tools Guarantee
This Silverline product comes with a 3 year guarantee.
To qualify you must register this product at silverlinetools.com within 30
days of purchase. The guarantee period begins on the date of purchase as
detailed on your sales receipt.
Terms & Conditions
This Guarantee and guarantee period becomes effective at the date of retail
purchase as detailed on your sales receipt.
PLEASE KEEP YOUR SALES RECIEPT
If this product develops a fault within 30 days of purchase, return it to the
stockist where it was purchased, with your receipt, stating details of the
fault. You will receive a replacement or refund.
If this product develops a fault after the 30 day period, return it to:
Silverline Tools Service Centre
PO Box 2988
Yeovil
BA21 1WU, UK
The guarantee claim must be submitted during the guarantee period.
You must provide the original sales receipt indicating the purchase date, your
name, address and place of purchase before any work can be carried out.
You must provide precise details of the fault requiring correction.
All claims will be veried by Silverline Tools that the deciencies are of a
material or manufacturing fault within the guarantee period.
We do not refund carriage. All products should be in a suitably clean and
safe state for repair, and should be packaged carefully to prevent damage or
injury during transportation. We may reject unsuitable or unsafe deliveries.
All work will be carried out by Silverline Tools or its authorised repair agents.
The repair or replacement of the product will not extend the period of
guarantee.
Defects recognised by us as being covered by the guarantee shall be
corrected by means of repair of the tool free of charge (excluding carriage
charges) or by replacement with a tool in perfect working order.
Retained tools, or parts, for which a replacement has been issued, will
become the property of Silverline Tools.
Inverter168754
Registering your purchase
Registration is made at silverlinetools.com by selecting the Guarantee
Registration button. You will need to enter:-
Your personal details•
Details of the product and purchase information •
Once this information is entered your guarantee certicate will be created in
PDF format for you to print out and keep with your purchase.
The repair or replacement of your product under guarantee provides benets
which are additional to and do not affect your statutory rights as a consumer.
What is covered:
The repair of the product, if it can be veried to the satisfaction of the
Silverline Tools that the deciencies were due to faulty materials or
workmanship within the guarantee period of purchase.
If any part is no longer available or out of manufacture, Silverline Tools will
replace it with a functional replacement part.
Use of the product in the EU.
What is not covered:
Silverline Tools does not guarantee repairs required as a result of:
Normal wear and tear caused by use in accordance with the operating
instructions eg blades, brushes, belts, bulbs, batteries etc.
The replacement of any provided accessories drill bits, blades, sanding
sheets, cutting discs and other related items.
Accidental damage, faults caused by negligent use or care, misuse, neglect,
careless operation or handling of the product.
Use of the product for anything other than normal domestic purposes.
Change or modication of the product in any way.
Use of parts and accessories which are not Silverline Tools genuine
components.
Faulty installation (except installed by Silverline Tools).
Repairs or alterations carried out by parties other than Silverline Tools or its
authorised repair agents.
Claims other than the right to correction of faults on the tool named in these
guarantee conditions are not covered by the guarantee.
EC Declaration of Conformity
The undersigned: Mr Philip Ellis
as authorized by: Silverline Tools
Declares that the
Name/ model: Inverter
Type/ serial no: 168754
Conforms to the following Directives:
Low Voltage Directive 2006/95/EC•
EN61558-1:2005•
EN61558-2:1997•
E8 Approval•
The technical documentation is kept by: Silverline Tools
Notified body: China Ceprei (Sichuan) Labratory
Place of declaration: Chengdu, China
Date: 10/08/09
Signed by:
Position in Company: Director
Name and address of Manufacturer or Authorised representative:
Silverline Tools, Boundary Way, Lufton Trading Estate, Yeovil, Somerset,
BA22 8HZ United Kingdom
www.silverlinetools.com
7
Loading...