Silverline Inverter Arc Welder User Manual [en, de, es, fr, it]

3 Year Guarantee

*Register online within 30 days. Terms & Conditions apply

Garantie de 3 ans *Enregistrez votre produit en ligne dans les 30 jours. Sous réserve des termes et conditions appliquées

3 Jahre Garantie *Registrieren Sie sich innerhalb von 30 Tagen online. Es gelten die allgemeinen Geschäftsbedingungen

3 años de garantía

*Regístrese online dentro de 30 días. Se aplican los términos y condiciones

3 anni di garanzia *Registrarsi on-line entro 30 giorni. Termini e Condizioni si applicano

3 Jaar Garantie *Registreer online binnen 30 dagen. Algemene voorwaarden van toepassing

www.silverlinetools.com

POWER

846386

10-100A

100A Inverter Arc Welder

100A Inverter Arc Welder Poste à souder à l'arc 100 A 100-A-Lichtbogenschweißgerät

www.silverlinetools.com

Soldador de arco inverter 100 A Saldatrice ad arco con inverter 100A Lasinverter 100 A

11 12 13

10-100A

100A Inverter Arc Welder

English .................. 4

Français ................ 8

Deutsch ................. 12

Español ................. 16

Italiano .................. 20

Nederlands ............ 24

www.silverlinetools.com

Description of Symbols

The rating plate on your tool may show symbols. These represent important information about the product or instructions on its use

Wear hearing protection Wear eye protection Wear breathing protection Wear head protection

Wear hand protection

Read instruction manual

Class I construction (protective earth)

Risk of electrocution

Conforms to relevant legislation and safety standards

Environmental Protection

Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice

Danger of toxic welding fumes

Danger of ultraviolet radiation

Danger hot Surfaces

Danger of Fire

Do not use in rain or damp environments

Speciﬁcation

Input voltage: ...........................230V ~50Hz

Rated duty cycle: .....................See table

Current range:..........................10-100A

No load voltage: .......................85V

Electrode size: .........................1.6 – 3.2mm

Case Protection Rating: ...........IP21

Protection Class: ......................

Cable Length:...........................2m

Weight: ....................................3.6kg

As part of our ongoing product development, speciﬁcations of

Silverline products may alter without notice.

Guide to current and electrode selection

Electrode/rod diameter Welding current

1.6mm 40-50A

2.0mm 50-70A

2.5mm 75-90A

3.2mm 90-100A

Duty cycle

Guide to the duty cycle of this welder. But note, the duty cycle will be affected by other factors such as the ambient temperature when welding

Duty cycle Welding current Working voltage

15% 100A 24,0V

60% 55A 22,2V

100% 45A 21,8V

Carefully read and understand this manual and any label attached to the tool before use. Keep these instructions with the product for future reference. Ensure all persons who use this product are fully acquainted with this manual.

Even when used as prescribed it is not possible to eliminate all residual risk factors. Use with caution. If you are at all unsure of the correct and safe manner in which to use this tool, do not attempt to use it.

General Power Tool Safety Warnings

WARNING Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, ﬁre and/ or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

Work Area Safety

a) Keep work area clean and well lit. Cluttered or dark areas invite

accidents

b) Do not operate power tools in explosive atmospheres, such as

in the presence of ﬂammable liquids, gases or dust. Power tools

create sparks which may ignite the dust or fumes

100A Inverter Arc Welder846386

c) Keep children and bystanders away while operating a power tool.

Distractions can cause you to lose control

Electrical Safety

a) Power tool plugs must match the outlet. Never modify the plug in

any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodiﬁed plugs and matching outlets will reduce risk

of electric shock

b) Avoid body contact with earthed or grounded surfaces, such as

pipes, radiators, ranges and refrigerators. There is an increased

risk of electric shock if your body is earthed or grounded

c) Do not expose power tools to rain or wet conditions. Water

entering a power tool will increase the risk of electric shock

d) Do not abuse the cord. Never use the cord for carrying, pulling or

unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the

risk of electric shock

e) When operating a power tool outdoors, use an extension cord

suitable for outdoor use. Use of a cord suitable for outdoor use

reduces the risk of electric shock

f) If operating a power tool in a damp location is unavoidable, use

a residual current device (RCD) protected supply. Use of an RCD

reduces the risk of electric shock

NOTE: The term “residual current device (RCD)” may be replaced by the term “ground fault circuit interrupter (GFCI)” or “earth leakage circuit breaker (ELCB)”.

Personal Safety

a) Stay alert, watch what you are doing and use common sense

when operating a power tool. Do not use a power tool while you are tired or under the inﬂuence of drugs, alcohol or medication.

A moment of inattention while operating power tools may result in serious personal injury

b) Use personal protective equipment. Always wear eye protection.

Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries

c) Prevent unintentional starting. Ensure the switch is in the

off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your

ﬁnger on the switch or energising power tools that have the switch on invites accidents

d) Remove any adjusting key or wrench before turning the power

tool on. A wrench or a key left attached to a rotating part of the power

tool may result in personal injury

e) Do not overreach. Keep proper footing and balance at all times.

This enables better control of the power tool in unexpected situations

f) Dress properly. Do not wear loose clothing or jewellery. Keep your

hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts

g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards

Power Tool Use & Care

a) Do not force the power tool. Use the correct power tool for your

application. The correct power tool will do the job better and safer at

the rate for which it was designed

b) Do not use the power tool if the switch does not turn it on and off.

Any power tool that cannot be controlled with the switch is dangerous and must be repaired

c) Disconnect the plug from the power source and/or the battery

pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive

safety measures reduce the risk of starting the power tool accidentally

d) Store idle power tools out of the reach of children and do

not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous

in the hands of untrained users

e) Maintain power tools. Check for misalignment or binding of

moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly

maintained power tools

f) Keep cutting tools sharp and clean. Properly maintained cutting

tools with sharp cutting edges are less likely to bind and are easier to control

g) Use the power tool, accessories and tool bits etc. in accordance

with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for

operations different from those intended could result in a hazardous situation

Service

a) Have your power tool serviced by a qualiﬁed repair person using

only identical replacement parts. This will ensure that the safety of

the power tool is maintained

Welding Safety

• Welding produces toxic fumes and can reduce oxygen levels in the work area. Always work in a well-ventilated area. Avoid inhaling welding fumes, use a suitable respirator where appropriate

• Some metal parts may have zinc, lead, cadmium or other coatings. Attempting to weld through these coatings can produce highly toxic fumes. Always remove all coatings before welding

• If you experience irritation to the lungs, throat or eyes whilst welding, STOP IMMEDIATELY and seek fresh air

• Welding produces extremely high levels of UV light. To prevent eye damage, ALWAYS use an approved welding face mask. Under no circumstances look directly at the arc

• The light produced when arc welding can be attractive to look at, especially to children. Always prevent other people from viewing the arc welding light with unprotected eyes

• If there is a possibility of other people approaching the work area, erect suitable screening to protect them from the light / glare

• Always replace the welder face mask glass as soon as it shows any signs of wear or damage

• To prevent skin damage, ALWAYS wear a suitable ﬁre-proof long sleeved jacket, heat proof gloves, and cap. Keep covered up

• Always remove any ﬂammable materials (e.g. cigarette lighter, matches) from your clothing before welding

• Always keep a ﬁre extinguisher nearby when welding

• Sparks generated while welding can ignite ﬂammable materials easily in

the welding area, so it is important to remove ﬂammable materials before commencing welding

• Only weld when the work area and all workpieces are dry

• Do not weld sealed containers (e.g. fuel tanks, air tanks, oil drums).

The heat generated from welding can cause sealed containers to burst without warning

• Be aware of transferred heat. Metal parts can conduct heat away from the work area and cause ignition of ﬂammable materials

• Be aware that welded parts will remain hot for some time after joining. Allow to cool completely before handling, or leaving unattended

• Never weld where ﬂammable gases, liquids or dust are present

• Ensure that there is always a responsible person nearby to alert you to

any ﬁre, or to call help in an emergency

• Use of welding machines will create powerful magnetic ﬁelds. This may disturb the operation of sensitive electronic equipment. Pacemaker wearers should consult a doctor before using a welding machine

• Do not overload power supply. Check that your mains wiring is capable of delivering the required current safely (see speciﬁcation)

www.silverlinetools.com

Product Familiarisation

1 Carry Strap

2 On/Off & Current Control Knob 3 Positive Socket 4 Electrode Clamp & Cable 5 Earth Clamp & Cable 6 Negative Socket 7 Overheating Indicator Light 8 Power Indicator Light

9 Welding Gloves 10 Welding Mask Fittings 11 Clear Filter 12 Tinted Filter 13 Filter Surround 14 Filter Catches 15 Welding Mask 16 Filter Window 17 Handle Mounting 18 Electrode Rod Pack 19 Welding Mask Handle 20 Hammer Brush

Unpacking Your Tool

• Carefully unpack and inspect your tool. Fully familiarise yourself with all its features and functions

• Ensure that all parts of the tool are present and in good condition. If any parts are missing or damaged, have such parts replaced before attempting to use this tool

Preparation

Assembling the Welding Mask

1. Insert the Clear Filter (11) into the Filter Surround (13). Place the Tinted

Filter (12) on top of the clear ﬁlter

2. Place the ﬁlter surround into the Filter Window (16) of the Welding

Mask (15) and rotate the Filter Catches (14) to secure the ﬁlter surround

3. Attach the Welding Mask Handle (19) to the Handle Mounting (17)

using the Welding Mask Fittings (10) Note: The clear ﬁlter acts as a splatter guard and protects the tinted ﬁlter from damage, therefore the tinted ﬁlter must be the ﬁlter closest to the operator’s eyes

Note: The handle ﬁts to the inside of the welding mask enclosure, so in use your hand is partly protected by the welding mask

Connecting the welding cables

IMPORTANT: Only connect the welding cables when the machine is not connected to the power supply

• Each cable is ﬁtted with a quick-connect plug. Insert the plug into the

correct socket on the welder and turn the plug clockwise to secure in position

1. Connect the Electrode Clamp and Cable (4) to the Positive Socket (3)

2. Connect the Earth Clamp and Cable (5) to the Negative Socket (6)

NOTE: These instructions are for conﬁguring the cables for DCEP use. However, there are electrodes that may need to be connected to the negative supply (DCEN) for optimum welding performance, depending on material, material thickness or the type of weld. Check information supplied by the electrode manufacturer regarding the type and polarity of the electrode you are using before connecting the welding cables

Connecting to a power supply

This arc welder is supplied pre-ﬁtted with a CEE 7/7 earthed 16A mains plug suitable for Germany and France, and other countries that adopt the same CEE 7/4 and 7/5 standards for mains sockets. If you do not have a suitable socket available compatible with a CEE 7/7 plug it will need to be replaced by a suitable plug or replacement cable with plug for your country. Depending on legislation in your country this may require ﬁtting by a qualiﬁed electrician. Alternatively a converter may be available to adapt the CEE 7/7 plug, but it must be earthed and capable of handling 16A.

Warning: This welder requires a 16A mains connection and is not suitable for connection to a UK 13A mains socket when used at 100A. For this reason it is not supplied with a pre-ﬁtted UK converter plug.

Note: For UK use, consult a qualiﬁed electrician with regards to installing a high current socket suitable for a welder that requires 16A. A suitable 16A plug (589694) and socket (571518) are available from your Silverline stockist, however the socket must be installed by a qualiﬁed electrician. It may be preferable to ﬁt a 32A plug (427717) and socket (457049) to allow your welder to be upgraded to a more powerful model at a later date.

Do not attempt to use this welder without an earth connection Do not connect this welder to a mains socket that is not rated to 16A Do not use an extension cable that is not capable of handling 16A, and

always fully unwind cable Do not connect the welder mains cable directly into high current circuit

terminals. Always use a plug and socket arrangement so the welder can be isolated when necessary

• ONLY connect this welder to a power supply capable of providing the speciﬁed voltage

• If connecting to a generator, check the speciﬁcation of the generator ﬁrst

WARNING:

• Welders operate at very high current levels at maximum settings: Do not overload your mains supply

• It may not be possible to use other high current devices at the same time as a welder if on the same circuit (for example, cooker, microwave, electric ﬁre etc.)

• If it is not convenient to disconnect other devices on your mains circuit, keep the welder at lower current settings

• At high current settings, it is possible that the welder may trip a fuse/ MCB in the fusebox/consumer unit. This is unlikely to be a fault with the welder, but may be an indicator your mains circuit is overloaded.

• If in any doubt, consult an electrician about connecting your welder

Before Use

• Always wear appropriate personal protective equipment for the job at hand. Use of this machine requires a welding mask, gloves, heat resistant clothing and, if appropriate, a respirator

• Always ensure there is an appropriate ﬁre extinguisher near to the work area

• Always inspect your machine for damage or wear. Pay particular attention to leads and cables. If any damage is found DO NOT USE

• Check that all casings or covers are completely closed and secured

• Position the welder to ensure that it will not move, or tip, in use. Ensure

that there is at least 500mm of clear space around the welder to allow sufﬁcient ventilation

• Although an arc welder is suitable for welding outside, never use a welder in rain or any area where it may come in contact with water. Always use extreme caution when using an arc welder outside and disconnect from power immediately after use

100A Inverter Arc Welder846386

Operating Instructions

Warning

• Always unplug the welding machine from the mains supply and allow to cool completely before attempting to ﬁt or replace any part

Setting the Machine

• The On/Off & Current Control Knob (2) switches the welder on and off and controls the welding current

• To achieve a good quality weld the current control knob must be set correctly (see guide to current and electrode selection for guidance)

• Turning the control knob clockwise will increase the welding current, turning the knob anti-clockwise will reduce the welding current

Welding rod selection

• In order to produce a good quality weld, the correct type of welding rod must be used. Welding rods are available in a variety of thicknesses and materials, and with a range of coatings

• Refer to rod manufacturers guidelines to select the correct rod for your requirements

Duty cycle / thermal cut out

• This machine is designed to weld constantly at 45A or below. For welding at greater currents, refer to the duty cycle

• The duty cycle deﬁnes a percentage of time in relation to overall time that the welder can be used for each current setting.

• If the machine is overloaded, or used beyond its duty cycle, it will automatically cut out and the Overheating Indicator Light (7) will illuminate

• Allow the machine to cool. The cut-out will automatically reset and the overheating indicator light extinguish once the machine is ready for use

• Using the machine at reduced current settings and maintaining good ventilation will maximise the duty cycle

• A duty cycle gives an approximate guide to how long you can use the welder. As an example, if the welder indicates over-heating and stops working at the 100A setting after 1.5 minutes of continuous use it is possible that it requires an approximate 8.5 minute cooling period before it can be used again, if the duty cycle is 15%. The operator should adjust the work pattern so it doesn’t force the welder into an over-heated condition which will maximise the lifespan of the unit. Therefore, only operating the unit for 1 minute every 5.5 minutes may prevent the welder going into over-heat mode and switching off

• Where possible try to avoid using the maximum amp settings where the duty cycle is 10 or 15%, as this will stress the internal components more than lower amp settings with higher duty cycles

Preparing to weld

• Ensure that parts to be joined are clean and free from rust, paint, or other ﬁnishes, using the supplied hammer brush to clean the surface if necessary

• All parts should be well supported, with a gap of approximately 1mm where you intend to form the welded joint

• Check that there are no ﬂammable materials in the vicinity of the work area

• Attach the Earth Clamp (5) to a cleaned area of one of the parts, as near as practical to where the weld will be. NEVER attach the earth clamp to the casing of the welder

• Squeeze the Electrode Clamp (4), to open the jaws. Place an electrode rod into the jaws and release. The electrode should be ﬁrmly gripped, with the clamp contacting the clean metal part (not the coated part)

• Carry out a ﬁnal check of the work area while reading the safety information provided in this manual

• Connect the welder to the mains power supply

Welding

WARNING: Using a welder correctly is a technical skill. A welder used

incorrectly can be highly dangerous. The information presented below is general guidance only. If you are not entirely conﬁdent in your ability to use this tool safely DO NOT USE.

• Turn the Current Control Knob (2) clockwise from the OFF position to the required current or thickness of electrode you are using, as indicated on the scale. The green Power Indicator Light (8) will illuminate

• Hold the Electrode Clamp (4) in one hand, and the welding mask in the other

• Position the rod at an angle of approx 60-75˚ angle from the surface or 15-30 ˚ from vertical, with the tip at approx 30mm away from the metal

• Hold the mask over your face, and tap the rod against the metal

• An arc should strike between the metal, and the tip. Try to hold the tip

of the rod a distance away from the metal equal to the rod thickness. Maintain the arc for 1-2 seconds, then move the rod away

• Allow the weld to cool slightly, and move the mask away from your face. If the settings were correct, a round ‘spot’ weld should have formed

• If the weld has not fully penetrated the metal, increase the current setting. If a hole has been made in the metal, reduce the current setting

• Practice making ‘spot’ welds until you are conﬁdent using the machine, and selecting settings

• To form a ‘seam’ weld, maintain the arc for longer, and slowly move the rod forward at the same time. The speed at which the rod is moved is crucial to achieving a good weld

• If the machine settings are correct, the arc should be steady, and produce a crackling sound. Be aware that you will have to gradually move the electrode clamp closer to the metal as the rod is used up

• Once the weld bead is complete, switch off the welder by turning the current control knob anticlockwise to position 0 on the scale. The green Power Indicator Light (8) will be extinguished

• Remove excess and splatters using the chipping hammer and wire brush. Do not attempt to weld over beads unless properly cleaned

• There are lots of different techniques for using arc welders which are beyond the scope of this manual. If you are new to welding, seek additional advice or training for exactly how you plan to use your arc welder. Always spend time conﬁguring the welder to the correct current, polarity (DCEP or DCEN) and use the appropriate size and type of electrode/rod

• Creating neat, high quality welds is a skill that takes time to master. Practice and good preparation will help to make satisfactory welds

Troubleshooting

Should you experience any problem with the welder please make the following checks:-

• That the welding current is correct for the diameter and type of electrode in use

• That the power supply is on, and the power indicator light is on. If the power indicator light is not on there is a power supply problem (for example a circuit breaker may have blown)

• That the correct voltage is being used as indicated on the rating plate

• That you have not exceeded the duty cycle and the thermal cut-out is

in operation

• That the cables are undamaged and that there is nothing causing a short circuit

• That all circuit connections are correct. You should pay particular attention to the work clamp, making sure that it is correctly attached to the workpiece and that there is no grease, paint or other contaminate that could cause a bad connection

www.silverlinetools.com

Maintenance

WARNING: Always remove the plug from the mains power supply before carrying out any maintenance/cleaning.

Cleaning

• Keep your machine clean at all times. Dirt and dust will cause internal parts to wear quickly, shortening the machine’s service life. Clean the body of your machine with a soft brush, or dry cloth. If available, use clean, dry, compressed air to blow through the ventila tion holes

• If the mains cable becomes damaged or worn it must be replaced by a qualiﬁed technician, with a cable equal or superior in current capacity to the original ﬁtted cable

• If the internal fuse blows, it must be replaced with a fuse of exactly the same type and rating as originally ﬁtted. If the replacement fuse blows immediately, it is likely to indicate a fault condition and a service technician should be consulted immediately

Disposal

Always adhere to national regulations when disposing of power tools that are no longer functional and are not viable for repair.

• Do not dispose of power tools, or other waste electrical and electronic equipment (WEEE), with household waste

• Contact your local waste disposal authority for information on the correct way to dispose of power tools

Silverline Tools Guarantee

This Silverline product comes with a 3 year guarantee

Register this product at www.silverlinetools.com within 30 days of purchase in order to qualify for the 3 year guarantee. Guarantee period begins according to the date of purchase on your sales receipt.

Terms & Conditions

Guarantee period becomes effective from the date of retail purchase as detailed on your sales receipt.

PLEASE KEEP YOUR SALES RECEIPT

If this product develops a fault within 30 days of purchase, return it to the stockist where it was purchased, with your receipt, stating details of the fault. You will receive a replacement or refund.

If this product develops a fault after the 30 day period, return it to:

Silverline Tools Service Centre PO Box 2988 Yeovil BA21 1WU, UK

The guarantee claim must be submitted during the guarantee period. You must provide the original sales receipt indicating the purchase date,

your name, address and place of purchase before any work can be carried out.

You must provide precise details of the fault requiring correction. Claims made within the guarantee period will be veriﬁed by Silverline Tools

to establish if the deﬁciencies are related to material or manufacturing of the product.

Carriage will not be refunded. Items for return must be in a suitably clean and safe state for repair, and should be packaged carefully to prevent damage or injury during transportation. We may reject unsuitable or unsafe deliveries.

All work will be carried out by Silverline Tools or its authorized repair agents.

The repair or replacement of the product will not extend the period of guarantee

Defects recognised by us as being covered by the guarantee shall be corrected by means of repair of the tool, free of charge (excluding carriage charges) or by replacement with a tool in perfect working order.

Retained tools, or parts, for which a replacement has been issued, will become the property of Silverline Tools.

EC Declaration of Conformity

The undersigned: Mr Darrell Morris as authorised by: Silverline Tools

Declares that the

Name/ model: 100A Inverter Arc Welder Product Code: 846386

Conforms to the following Directives:

• LVD Directive 2006/95/EC

• EMC Directive 2004/108/EC

• ROHS Directive 2002/95/EC

• PPE Directive 89/86/EEC

• EN60974-10:2007

• EN60974-1:2005

• EN175:1997-08

• EN169:2002

• EN420:2003

• EN388:2003

• EN12477:2001

100A Inverter Arc Welder846386

Registering your purchase

Registration is made at silverlinetools.com by selecting the Guarantee Registration button. You will need to enter:-

• Your personal details

• Details of the product and purchase information

Once this information is entered your guarantee certiﬁcate will be created in PDF format for you to print out and keep with your purchase.

The repair or replacement of your product under guarantee provides beneﬁts which are additional to and do not affect your statutory rights as a consumer.

What is covered:

The repair of the product, if it can be veriﬁed to the satisfaction of Silverline Tools that the deﬁciencies were due to faulty materials or workmanship within the guarantee period.

If any part is no longer available or out of manufacture, Silverline Tools will replace it with a functional replacement part.

Use of this product in the EU.

What is not covered:

Silverline Tools does not guarantee repairs required as a result of: Normal wear and tear caused by use in accordance with the operating

instructions eg blades, brushes, belts, bulbs, batteries etc. The replacement of any provided accessories drill bits, blades, sanding

sheets, cutting discs and other related items. Accidental damage, faults caused by negligent use or care, misuse,

neglect, careless operation or handling of the product. Use of the product for anything other than normal domestic purposes. Change or modiﬁcation of the product in any way. Use of parts and accessories which are not genuine Silverline Tools

components. Faulty installation (except installed by Silverline Tools). Repairs or alterations carried out by parties other than Silverline Tools or its

authorized repair agents. Claims other than the right to correction of faults on the tool named in

these guarantee conditions are not covered by the guarantee.

The technical documentation is kept by: Silverline Tools

Notiﬁed body: Jiangsu TUV Product Service

Place of declaration: Shanghai, China

Date: 17/12/12

Signed by:

Director

Name and address of Manufacturer or Authorised representative:

Silverline Tools, Boundary Way, Lufton Trading Estate, Yeovil, Somerset,

BA22 8HZ, United Kingdom

www.silverlinetools.com

Description des symboles

La plaque signalétique ﬁgurant sur votre outil peut présenter des symboles. Ces symboles constituent des informations importantes relatives au produit ou des instructions concernant son utilisation.

Port de protection auditive Port de lunettes de sécurité Port du masque respiratoire Port du casque

Port de gants

Lire le manuel d’instructions

Construction de classe I (liaison à la masse).

Risque d’électrocution

Conforme à la réglementation et aux normes de sécurité pertinentes

Protection de l’environnement

Les produits électriques usagés ne doivent pas être jetés avec les ordures ménagères. Veuillez les recycler dans les centres prévus à cet effet. Pour de plus amples informations, veuillez contacter votre municipalité ou point de vente

Danger : Fumée toxique

Danger : Radiation d’ultraviolets

Danger : Surfaces chaudes

Caractéristiques techniques

Tension : ...........................................230V~ 50 Hz

Cycle opératoire nominal : ................Voir table ci-dessous

Variations de courant nominal : ........10-100 A

Diamètre de l’électrode : ..................1,6 – 3,2mm

Tension à vide : .................................85 V

Classe de protection : .......................

Degré de protection : ........................IP21S

Longueur du câble : ..........................2 m

Poids :...............................................3,6 kg

Du fait de l’évolution constante de nos produits, les spéciﬁcations des

produits Silverline peuvent changer sans notiﬁcation préalable.

Diamètre de la baguette de soudure en fonction de l’intensité du courant de soudure.

Ø Intensité

1.6mm 40-50 A

2.0mm 50-70 A

2.5mm 75-90 A

3,2 mm 90 – 100 A

Cycle opératoire en fonction de l’intensité et la tension du courant de soudure.

Cycle opératoire Intensité Tension

15% 100 A 24 V

60% 55 A 22,2 V

100% 45 A 21.8 V

10F10

Danger : Risques d’incendie

Ne pas utiliser sous la pluie ou dans un environnement humide

Lisez attentivement ce manuel ainsi que toute étiquette apposée sur l’outil et assurez-vous d’en comprendre le sens avant utilisation. Rangez ces consignes avec l’outil, pour référence ultérieure. Assurez-vous que toute personne venant à utiliser cet outil ait attentivement pris connaissance de ce manuel.

Sachez qu’utiliser un outil conformément aux prescriptions ne garantit pas l’élimination de tous les facteurs de risque. Procédez avec prudence. N’utilisez pas cet outil si vous avez des doutes quant à la manière sûre et correcte de procéder.

Consignes générales de sécurité relatives aux appareils électriques

AVERTISSEMENT Veuillez lire l’intégralité des consignes de sécurité et des instructions. Le non-respect de ces consignes et instructions peut

entraîner un risque de choc électrique, d’incendie et/ou se traduire par des blessures graves

Veuillez conserver ces instructions et consignes de sécurité pour référence ultérieure.

L’expression « appareil électrique » employée dans les présentes consignes recouvre aussi bien les appareils ﬁlaires à brancher sur le secteur que les appareils sans ﬁls fonctionnant sous batterie.

Poste à souder à l'arc 100 A846386

Sécurité sur la zone de travail

a) Maintenir une zone de travail propre et bien éclairée. Des zones

encombrées et mal éclairées sont sources d’accidents.

b) Ne pas utiliser d’outils électriques dans des environnements

explosifs, tels qu’à proximité de liquides, de gaz ou de poussières inﬂammables. Les appareils électriques produisent des étincelles

susceptibles d’enﬂammer la poussière ou les vapeurs présentes.

c) Eloigner les enfants et les passants pendant l’utilisation d’un

appareil électrique. Ceux-ci peuvent provoquer une perte d’attention

et faire perdre la maîtrise de l’appareil.

Sécurité électrique

a) La prise d’un appareil électrique doit être adaptée à la prise du

secteur. Ne jamais modiﬁer la prise en aucune façon. Ne jamais utiliser d’adaptateur sur la prise électrique d’appareil mis à la terre. Des prises non modiﬁées, adaptées aux boîtiers de prise de

courant, réduiront le risque de décharge électrique.

b) Eviter le contact corporel avec les surfaces mises à la terre telles

que tuyaux, radiateurs, cuisinières et réfrigérateurs. Le risque de

décharge électrique est plus important si le corps est mis à la terre.

c) Ne pas exposer l’appareil électrique à la pluie ou à l’humidité.

L’inﬁltration d’eau dans un appareil électrique accroît le risque de décharge électrique.

d) Ne pas maltraiter le cordon électrique. Ne jamais utiliser le

cordon électrique pour porter, tirer ou débrancher l’appareil. Protéger le cordon électrique de la chaleur, du contact avec l’essence, des bords tranchants et pièces rotatives. Un cordon

électrique endommagé ou entortillé accroît le risque de décharge électrique.

e) Lors d’une utilisation de l’appareil électrique en extérieur, se

servir d’une rallonge appropriée à une utilisation en extérieur.

Cela réduit le risque de décharge électrique.

f) Si une utilisation de l’appareil électrique dans un environnement

humide ne peut être évitée, utiliser une alimentation protégée par un disjoncteur différentiel. L’utilisation d’un disjoncteur différentiel

réduit le risque de décharge électrique.

Sécurité des personnes

a) Rester vigilent et faire preuve de bon sens lors de la manipulation

de l’appareil. Ne pas utiliser un appareil électrique lorsque l’on se trouve dans un état de fatigue, ou sous l’inﬂuence de drogues, d’alcool ou de médicaments. Un moment d’inattention pendant

l’utilisation d’un outil électrique peut se traduire par des blessures graves.

b) Porter un équipement de protection approprié. Toujours porter

une protection oculaire. Le port de masque à poussières, chaussures

de sécurité antidérapantes, casque de sécurité et protections antibruit adaptés aux différentes conditions de travail réduit le risque de blessures corporelles.

c) Eviter tout démarrage accidentel. S’assurer que l’interrupteur

marche-arrêt soit en position d’arrêt avant de brancher l’appareil sur l’alimentation secteur ou d’installer la batterie, de prendre l’appareil ou de le transporter. Porter un appareil électrique tout en

maintenant le doigt posé sur l’interrupteur ou brancher un appareil électrique dont l’interrupteur est sur la position de marche est source d’accidents.

d) Enlever toute clé et tout instrument de réglage avant de mettre

l’appareil électrique en marche. Une clé ou un instrument de

réglage laissé ﬁxé à un élément en rotation de l’appareil électrique peut entraîner des blessures physiques.

e) Ne pas essayer d’atteindre une zone hors de portée. Se tenir

toujours en position stable permettant de conserver l’équilibre.

Cela permet de mieux contrôler l’appareil électrique dans des situations inattendues.

f) Porter des vêtements appropriés. Ne pas porter de vêtements

amples ou des bijoux pendants. Eloigner cheveux, vêtements et gants des pièces en mouvement. Les vêtements amples, les bijoux

pendants et cheveux longs peuvent être happés par les pièces en rotation.

g) Si l’appareil est pourvu de dispositifs destinés au raccord

d’équipements d’extraction et de récupération de la poussière/ sciure, s’assurer qu’ils soient bien ﬁxés et utilisés correctement

L’utilisation de ces dispositifs peut réduire les risques dus à la poussière.

Utilisation et entretien des appareils électriques

a) Ne pas forcer sur l’appareil électrique. Utiliser l’appareil

électrique approprié au travail à effectuer. Un appareil électrique

adapté et employé au rythme pour lequel il a été conçu permettra de réaliser un travail de meilleure qualité et dans de meilleures conditions de sécurité.

b) Ne pas utiliser un appareil électrique dont l’interrupteur marche-

arrêt est hors service. Tout appareil électrique dont la commande

ne s’effectue plus par l’interrupteur marche-arrêt est dangereux et doit être réparé.

c) Débrancher l’appareil électrique ou démonter sa batterie avant

d’effectuer tout réglage ou changement d’accessoire et avant de le ranger. De telles mesures préventives réduiront les risques de

démarrage accidentel.

d) Ranger les appareils électriques inutilisés hors de portée des

enfants et ne pas permettre l’utilisation de cet appareil aux personnes non habituées à son maniement ou n’ayant pas lu les présentes instructions. Les appareils électriques sont dangereux

dans les mains d’utilisateurs inexpérimentés.

e) Veiller à l’entretien des appareils électriques. Vériﬁer que les

éléments rotatifs soient bien alignés et non grippés. S’assurer de l’absence de pièces cassées ou endommagées susceptibles de nuire au bon fonctionnement de l'appareil. Si l’appareil électrique est endommagé, le faire réparer avant toute utilisation.

De nombreux accidents sont dus à l’utilisation d’appareils électriques mal entretenus.

f) Veiller à ce que les outils de coupe soient tenus affûtés et

propres. Des outils de coupe bien entretenus, aux tranchants bien

affûtés, sont moins susceptibles de se gripper et sont plus faciles à contrôler.

g) Utiliser l’appareil électrique, les accessoires et outils à monter

conformément à ces instructions, en tenant compte des conditions de travail et de la tâche à réaliser. Toute utilisation d’un

appareil électrique autre que celle pour laquelle il a été conçu peut entraîner des situations à risque.

Révision

a) Ne faire réparer votre appareil électrique que par un réparateur

qualiﬁé utilisant uniquement des pièces de rechange identiques.

Cela permet de maintenir la sécurité d’utilisation de l’appareil électrique.

Consignes de sécurité relatives à la soudure

• La soudure peut produire de la fumée toxique et réduire le taux d’oxygène présent dans la zone de travail. Travaillez toujours dans un endroit bien ventilé. Evitez d’inhaler la fumée émise par la soudure et portez un masque respiratoire lorsque l’activité s’y prête.

• Certaines parties métalliques peuvent être galvanisées ou revêtues de plomb, de cadmium ou d’autres revêtements. Souder sur ces revêtements peut produire de la fumée hautement toxique. Décapez toujours la surface avant de procéder au soudage.

• Si vous ressentez une irritation aux poumons, à la gorge ou aux yeux pendant le soudage, ARRETEZ-VOUS IMMEDIATEMENT et sortez à l’air pur.

• La soudure produit des taux extrêmement élevés d’ultraviolets. Pour éviter d’altérer votre vue, portez TOUJOURS un masque à souder agréé. Ne regardez JAMAIS directement l’arc.

• La lumière éblouissante produite pendant le soudage est attractive à regarder spécialement pour les enfants. Toujours empêcher les autres personnes de regarder cette lumière sans protection oculaire.

www.silverlinetools.com

+ 28 hidden pages

Silverline Inverter Arc Welder User Manual [en, de, es, fr, it]

Specifications and Main Features

Frequently Asked Questions

User Manual