Page 1
Multicast Distribution System
X-5
User's Guide
- Multicast Distribution Feature -
WA101050XA
Page 2
Copyright© 2016 silex technology, Inc. All rights reserved.
Page 3
Index
1. Introduction ..................................................................... 1
1-1. This Manual ............................................................................................................................ 1
Disclaimers .................................................................................................................................. 1
Trademarks ................................................................................................................................. 1
1-2. User Registration and Services for X-5 ......................................................................... 2
User Registration ...................................................................................................................... 2
Services ........................................................................................................................................ 2
Customer Support Center ..................................................................................................... 2
2. X-5 ................................................................................ 3
2-1. Features and System Conguration .............................................................................. 4
Features ........................................................................................................................................ 4
System Conguration ............................................................................................................. 5
2-2. Parts and Functions ............................................................................................................. 6
2-3. Product Specications .....................................................................................................11
Basic Specications ................................................................................................................ 11
Communication Protocol Specications ........................................................................14
Interface Specications ........................................................................................................ 14
2-4. Usage Notes ......................................................................................................................... 15
Wireless Signals .......................................................................................................................15
Copyrights for Video and Audio Content .......................................................................17
3. X-5 Settings and Installation ...................................19
3-1. Required Items .................................................................................................................... 19
3-2. Building the Setting Environment ...............................................................................21
Page 4
3-3. X-5 Settings ..........................................................................................................................23
Assigning IP Addresses .........................................................................................................23
Parameter Settings .................................................................................................................25
Screen Adjustment ................................................................................................................31
3-4. X-5 Installation ....................................................................................................................33
Characteristics of Supplied Antenna ............................................................................... 34
Obtaining Line of Sight ........................................................................................................35
4. Video and Audio Distribution and Maintenance ...37
4-1. Video and Audio Distribution ........................................................................................ 37
4-2. Maintenance Using the Web Interface ....................................................................... 38
Accessing the Web Page of X-5..........................................................................................38
Status Page ...............................................................................................................................40
Conguration Page ................................................................................................................44
Management Page .................................................................................................................51
4-3. Initialization of Settings ................................................................................................... 56
A. Appendix ..................................................................57
A-1. List of Setting Items .......................................................................................................... 57
Page 5
1. Introduction
1
Thank you for purchasing the Multicast Distribution System X-5 (called "X-5" below).
Disclaimers
1.
Introduction
- The unauthorized transfer or copying of the content of this manual, in whole or in part,
without prior written consent is expressly prohibited by law.
- The content of this manual is subject to change without notice.
- This manual was prepared to accurately match the content of each OS, but the actual
information shown on the computer monitor may differ from the content of this manual
due to future OS version upgrades, modifications, and other changes.
- Although every effort was made to prepare this manual with the utmost accuracy, Silex
Technology will not be held liable for any damages as a result of errors, setting examples,
or other content.
Trademarks
- Microsoft and Windows are registered trademarks of Microsoft Corporation in the United
States and/or other countries.
- Ethernet is a trademark of Xerox Corporation.
- Other company names and product names contained in this manual are trademarks or
registered trademarks of their respective companies.
1-1. This Manual
X-5 includes a Multicast Distribution feature for IP multicast transfer of video/audio from
players (computers and DVD players) to displays (TVs and monitors) and a Store & Play
feature for playing back video in storage devices using the receiver only.
This manual describes the setting and operating procedures when using the Multicast
Distribution feature of X-5. For details on using the Store & Play feature, refer to the
separate manual "User's Guide: Store & Play Feature".
Page 6
2
X-5 User's Guide
1-2. User Registration and Services for X-5
To enable us to provide better services (support and repair), please perform the user
registration process from our website.
User registration is performed from the URL below.
USA: http://www.silexamerica.com/support/product-registration/
Japan: http://www.silex.jp/register/
- The product serial number is required for user registration.
The serial number is provided on the rear panel of the product.
Note
User Registration
- Latest firmware available for download
- Latest software available for download
- Latest manuals available for download
- Support Information (FAQ)
Services
The services below are available from the Silex Technology website. For details, please visit
the Silex Technology website.
USA: http://www.silexamerica.com/
Japan: http://www.silex.jp/
Customer Support Center
Customer Support is available by e-mail or telephone for any problems that you may
encounter.
If you cannot find the relevant problem in this manual or on our website, or if the corrective
procedure does not resolve the problem, please contact Silex Technology Customer
Support.
Contact Information
Phone E-mail
USA +1-801-748-1199
support@silexamerica.com
Japan +81-(0)774-98-3981
support@silex.jp
- Refer to the Silex Technology website (http://www.silexamerica.com/) for the latest FAQ and available
product information.
Note
Page 7
2. X-5
3
2.
X-5
MDS is an abbreviation for Multicast Distribution System and is a system for IP multicast
transfer of the video/audio from players (computers and DVD players) to displays (TVs and
monitors).
The devices connected to computers, DVD players, and other players are referred to
as "transmitters", and the devices connected to projectors and displays are referred to
as "receivers". The transmitter encodes the signals that are output from the player and
distributes the encoded data in realtime to the receiver, where the data is then decoded
and output.
Page 8
4
X-5 User's Guide
Features
2-1.
Features and System Configuration
The features and system configuration of X-5 are shown below.
[Video and Audio Control]
- Uses Silex Technology's proprietary "JPEG-XR" as video codec
-
Uses 16-bit stereo+monaural PCM (sampling rate: 32KHz / 44.1KHz / 48KHz) as audio codec
- Multi-resolution support (640 x 480 to 1920 x 1080)
- Maximum frame rate of 30 fps
- Includes video and audio synchronizing function ("Lip-sync")
- Includes Store & Play feature for playing back video on a storage device using the
receiver only.
(*For details on using X-5 with the Store & Play feature, refer to the separate manual
"User's Guide: Store & Play Feature".)
[Network Control]
- Multicast for enabling simultaneous batch sending to multiple receivers
(During wired connection: Up to 1000 receivers, During wireless connection: Up to 32
receivers)
- Time correction with transmitter of receiver enables playback synchronization
between receivers
- Support for both wired LANs (10Base-T/100Base-TX/1000Base-T) and
wireless LANs
(IEEE802.11a/g/n: Infrastructure mode)
- Network interface select function of transmitter enables distribution of data only
to the network interfaces connected by a receiver (wired LAN or wireless LAN) for
reducing traffic of networks where the receiver is not connected
- Support for remote management function based on SX Smart Manager (sold
separately)
[Other Features]
- Internal web page for making various settings
Page 9
2. X-5
5
System Configuration
An example of a network system configuration using X-5 is shown below.
Wireless
(IEEE 802.11a/n)
Hub/Switch
Wireless
Wired
Transmitter
Player
Receiver Display
Receiver
Display
Receiver
Display
Receiver
Display
Receiver
Display
Receiver Display
Page 10
6
X-5 User's Guide
2-2. Parts and Functions
The names and functions of X-5T / X-5R are shown below.
(The transmitter (X-5T) and receiver (X-5R) have an identical appearance. They can be
distinguished by the model name written on the label on the rear panel.
When they are
turned on, it is possible to distinguish the model by a color of PWR LED.)
(Front Panel)
(Top Panel)
(1)
(3)
(4)
(5)
(6)
(2)
[ X-5T / X-5R ]
Page 11
2. X-5
7
Status
(1) Function switch Transmitter:
(Function is not assigned.)
Receiver:
If multiple transmitters are installed in the network when using the multicast distribution
feature, the transmitter that distributes the video can be switched.
(2)
Wireless LAN antenna This is an antenna for performing wireless LAN communication.
(3) PWR LED
(green/orange/red)
Solid green Transmitter mode (X-5T)
Solid orange Receiver mode (X-5R)
Flashing red Uploading the firmware
(4) STAT LED
(green/orange/red)
Flashing green Video conversion in progress (transmitter digital)
Flashing orange Video conversion in progress
(transmitter analog, receiver digital/analog)
Solid red Resolution error, video conversion process error
(5) LAN LED
(green/orange)
Solid green 1000Base Link (connected to TX or RX)
Flashing green 1000Base Link (not connected to TX or RX)
Solid orange 10/100Base Link (connected to TX or RX)
Flashing orange 10/100Base Link (not connected to TX or RX)
(6) WLAN LED
(green/orange/red)
Solid green Host mode (connected to TX or RX by wireless LAN)
Flashing green Host mode (no wireless link/not connected to TX or RX)
Solid orange Client mode (connected to TX or RX by wireless LAN)
Flashing orange Client mode (no wireless link/not connected to TX or RX)
Flashing red Communication error in wireless LAN
(7) Power connector Connects the AC adapter.
(8) USB port Connects a USB storage device.
Transmitter:
(Function is not assigned.)
Receiver:
Saves the content data.
(9) Status LED (yellow) On Receiving packets (turns on at 0.5-second intervals when receiving)
Off Not receiving packets
(10) Link LED
(green/orange)
Solid green 1000Base Link (communicating with TX or RX)
Solid orange 10/100Base Link (communicating with TX or RX)
Off Link not established
(11) Audio output jack Connects the audio cable (audio output jack).
(12) DVI-I connector Connects the DVI cable.
(13) RESET switch Returns X-5 settings to the factory defaults.
(For the detailed operating procedure, see "4-3 Initializing the Settings".)
(14) Network port Connects the network cable.
(Bottom Panel)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
(14)
Page 12
8
X-5 User's Guide
(2)
The names and functions of X-5SR are shown below.
(Front Panel)
(Top Panel)
FN
(1)
[ X-5SR ]
(3)
(4)
(5)
(6)
Page 13
2. X-5
9
(Bottom Panel)
DC5V IN
AUDIO
DVI
ETHER
microSD
(7)
(8)
(9)
(10)
(11)
(12)
(13)
(Side Panel)
USB
RESET
Status
(1) Function switch If multiple transmitters are installed in the network when using the multicast
distribution feature, the transmitter that distributes the video can be switched.
(2)
Wireless LAN antenna This is an antenna for performing wireless LAN communication.
(3) PWR LED
(green/orange/red)
Solid green (Function is not assigned.)
Flashing green Copying data from USB thumb drive to microSD card.
Solid orange Receiver mode (X-5SR)
Data copy from USB thumb drive to microSD card has successfully
been completed. Now, it is safe to remove the USB thumb drive.
Flashing orange Data copy from USB thumb drive to microSD card has failed.
The copy has failed but it is safe to remove the USB thumb drive.
Solid red Uploading the firmware
(4) STAT LED
(green/orange/red)
Flashing green (Function is not assigned.)
Flashing orange Video conversion in progress
(receiver digital)
Solid red Resolution error, video conversion process error
(5) LAN LED
(green/orange)
Solid green 1000Base Link (connected to TX)
Flashing green 1000Base Link (not connected to TX)
Solid orange 10/100Base Link (connected to TX)
Flashing orange 10/100Base Link (not connected to TX)
(14)
(15)
Page 14
10
X-5 User's Guide
(6) WLAN LED
(green/orange/red)
Solid green Host mode (connected to TX by wireless LAN)
Flashing green Host mode (no wireless link/not connected to TX)
Solid orange Client mode (connected to TX by wireless LAN)
Flashing orange Client mode (no wireless link/not connected to TX)
Flashing red Communication error in wireless LAN
(7) microSD slot Insert a microSD card which will save the content data.
* After a microSD card is inserted to the slot, x it by screwing the cover that came with X-5.
(8) Power connector Connects the AC adapter.
(9) Status LED
(yellow)
On Receiving packets (turns on at 0.5-second intervals when receiving)
Off Not receiving packets
(10) Link LED
(green/orange)
Solid green 1000Base Link (communicating with TX)
Solid orange 10/100Base Link (communicating with TX)
Off Link not established
(11) Audio output jack Connects the audio cable (audio output jack).
(12) DVI-D connector Connects the DVI-D cable.
(13) Network port Connects the network cable.
(14) RESET switch Returns X-5 settings to the factory defaults.
(For the detailed operating procedure, see "4-3 Initializing the Settings".)
(15) USB port Connects a USB storage device.
- When the PWR LED blinks Green, data copy is in process from USB thumb drive to microSD card. When the
data copy has successfully been completed, the PWR LED will turn Orange, and when it has failed, the PWR
LED will blink Orange. In both cases, the USB thumb drive can safely be removed.
- If all of four LEDs blink Red at the front of X-5 , it is not safe to remove the USB thumb drive. In such a case,
disconnect the AC plug from outlet before you remove the USB thumb drive.
TIP
- If the PWR LED blinks Orange, data copy from USB thumb drive may have failed due to a lack of available
disk space on the microSD card.
- The PWR LED will stop blinking Orange and start to constantly turn Orange after the USB thumb drive is
removed.
Note
Page 15
2. X-5
11
2-3. Product Specifications
CPU Marvell "88F6180" 800MHz (32-bit ARM)
RAM 128 MB DDR
ROM 16 MB
Interface Video DVI-I x 1
(Analog RGB input/output uses conversion cable.)
Audio 3.5mm stereo mini-jack x 1
Ethernet 10BASE-T/100BASE-TX / 1000BASE-T Auto-detect (RJ-45) x 1
Wireless IEEE802.11a/b/g/n mini PCIe module x 1 (SX-PCEAN)
Power supply AC adapter (operating voltage: 5 V)
LED Front panel: 4 LEDs
"PWR" / "STAT" / "WLAN" / "LAN"
Bottom panel: 2 LEDs
RJ-45 "Link" / "Status"
Push switch Top panel: Function switch
Bottom panel: Setting reset switch
Video input/output support Resolution auto-detect
Supported resolution
Digital
(*1)
Analog
(*1)(*2)
VGA (640x480)
480p (720x480)
SVGA (800x600)
XGA (1024x768)
720p (1280x720)
(*3)
WXGA (1280x768)
(*3)
WXGA (1360x768)
(*3)
SXGA (1280x1024)
(*3)
WSXGA (1600x1024)
(*3)
Full-HD (1920x1080)
(*3)
(*1) The supported digital and analog refresh rate is 60 Hz only.
(*2)
An analog connection requires a D-sub 15-pin DVI-I conversion adapter or cable.
(*3) The transmitter is not supported, but Store & Play mode in the receiver is supported.
Basic Specifications
[ X-5T / X-5R ]
Page 16
12
X-5 User's Guide
CPU Marvel ARMADA370 800MHz (32bit ARM)
RAM 128 MB DDR
ROM 16 MB
Interface Video DVI-D x 1
Audio 3.5mm stereo mini-jack x 1
Ethernet 10BASE-T/100BASE-TX / 1000BASE-T Auto-detect (RJ-45) x 1
Wireless IEEE802.11a/b/g/n mini PCIe module x 1 (SX-PCEAN)
Power supply AC adapter (operating voltage: 5 V)
LED Front panel: 4 LEDs
"PWR" / "STAT" / "WLAN" / "LAN"
Bottom panel: 2 LEDs
RJ-45 "Link" / "Status"
Push switch Top panel: Function switch
Side panel: Setting reset switch
Video output support Resolution auto-detect
Supported resolution
Digital
(*1)
VGA (640x480)
480p (720x480)
SVGA (800x600)
XGA (1024x768)
720p (1280x720)
WXGA (1280x768)
WXGA (1360x768)
SXGA (1280x1024)
WSXGA (1600x1024)
Full-HD (1920x1080)
(*1) The supported refresh rate is 60 Hz only.
[ X-5SR ]
Page 17
2. X-5
13
Federal Communication Interference Statement (United States only)
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment
in a residential area is not allowed as it is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
This radio module and its antenna(s) must not be co-located or operated in conjunction with any other antenna or transmitter.
Canadian Department of Communications Industry Canada Notice (Canada only)
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
FCC Rules, Part 15 / Industry Canadian
This device complies with Part 15 of FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following
two conditions:
This device may not cause harmful interference, and
This device must accept any interference, including interference that may cause undesired operation of this device.
Le présent appareil est conforme aux la partie 15 des règles de la FCC et CNR d'Industrie Canada applicables aux appareils radio exempts
de licence. L'exploitation est autorisée aux deux conditions suivantes :
l'appareil ne doit pas produire de brouillage, et
l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio
frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment
should be installed and operated with the radiator at least 20cm or more away from person’s body (excluding extremities: hands, wrists,
feet and ankles).
Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un environnement no contrôlé et respecte les
règles les radioélectriques (RF) de la FCC lignes directrices d'exposition dans le Supplément C à OET65 et d’exposition aux fréquences
radioélectriques (RF) CNR-102 de l’IC. Cet équipement doit être installé et utilisé en gardant une distance de 20 cm ou plus entre le
dispositif rayonnant et le corps (à l’exception des extrémités : mains, poignets, pieds et chevilles).
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser)
gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and
its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful
communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et
d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.
This radio transmitter 4908B-SXPCEAN has been approved by Industry Canada to operate with the antenna types listed below with the
maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list,
having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Le présent émetteur radio 4908B-SXPCEAN a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés cidessous et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans
cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.
For product available in the USA/Canada market, only channels 1~11 can be operated. Selection of other channels is not possible. If this
device is to be operated in the 5.15~5.35GHz frequency range, it is restricted to indoor environment only.
Antenna information: Sleeve Antenna: 1.5dBi (2.4GHz), 2.1dBi (5GHz)
Frequency Tolerance: +/-20ppm
WARNING:
The FCC / Industry Canada regulations provide that changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
FCC / IC Notice
Page 18
14
X-5 User's Guide
Video
Interface DVI-I (X-5T / X-5R), DVI-D (X-5SR)
Codec JPEG-XR (proprietary)
Resolution Auto-detect of VGA (640 x 480) to Full-HD (1920 x 1080)
Frame Rate Maximum 30 fps
Setting Image position adjustment
Audio
Interface 3.5mm stereo mini-jack
Codec 16-bit PCM
Sampling rate 32 KHz, 44.1 KHz, 48 KHz
USB
Standards USB 2.0 Hi-Speed (USB 3.0 Super Speed is backward compatible)
Memory Up to 32GB
File system FAT, FAT32
Partition 1 partition only
Device insertion or removal
while the unit is powered on
X-5T / X-5R: Insertion/removal of USB thumb drive is prohibited.
X-5SR: Insertion of USB thumb drive is allowed any time when X-5SR is powered on.
Removal of USB thumb drive is allowed when it is safe to remove it.
(For when it is safe to remove USB thumb drive, refer to 2-2. Parts and Functions.)
microSD
Supported media micro SD, micro SDHC
Memory micro SD: Up to 2GB, micro SDHC: Up to 32GB
File system FAT, FAT32
Partition 1 partition only
Device insertion or removal
while the unit is powered on
Insertion/removal of micro SD card is prohibited.
Interface Specifications
TCP/IP Network layer ARP, RARP, IPv4, ICMP
IPv4 Organization Local Scope
"239.192.0.0/14" is used for multicasting
Transport layer TCP, UDP
Application layer TELNET, BOOTP, DHCP, HTTP, JCP (proprietary #19541), RTP (proprietary
#50001 to #65535),
X-5 Announcement Protocol (proprietary #50000),
SX-RPC (proprietary via HTTP/RTP), NTP, DNS
Other FLDP For firmware updating
Communication Protocol Specifications
Page 19
2. X-5
15
2-4. Usage Notes
Wireless Signals
Do not use X-5 near the equipment below.
- Industrial, scientific, and medical equipment such as microwave ovens and
pacemakers
- Short-range wireless base stations (wireless base stations that require a license) for
mobile identification used in factory manufacturing lines and other applications
- Low-power wireless base stations (wireless base station that do not require a license)
The above equipment uses the same signal frequency band as wireless LANs. Signal
interference can occur if X-5 is used near the above equipment. This can result in a
communication failure or slow communication speeds.
Cellular phones, PHS, televisions, radios, and other devices use a different frequency
band than the wireless LAN. Therefore, use of these devices near X-5 will not affect
communication by X-5 or by these devices. However, if these devices are brought near a
wireless LAN product, noise may occur in the audio or video due to the electromagnetic
waves generated by X-5 and other wireless LAN products.
Avoid use of X-5 near cellular telephones, PHS, televisions, and radios as much as
possible.
Communication is not possible through reinforced steel, metal, or concrete barriers.
The signals used in X-5 will pass through wood, glass, and other barriers used in a typical
home, and so communication is possible even in rooms with walls made from wood or
glass.
However, the signals will not pass through barriers made of reinforced steel, metal,
concrete, or similar materials.
Communication cannot be performed in rooms with walls made from these types of
materials.
In the same way, communication cannot be performed through floors using reinforced
steel, metal, concrete, or similar materials.
Page 20
16
X-5 User's Guide
Wireless Equipment Using the 2.4 GHz and 5 GHz Bands
The operating frequency band of this equipment is used by microwave ovens, industrial,
scientific, and medical equipment, and also by short-range wireless base stations (wireless
base stations that require a license) and low-power wireless base stations (wireless
base station that do not require a license) for mobile identification used in factory
manufacturing lines and other applications.
- Before using this equipment, check that there are no short-range wireless base
stations or low-power wireless base stations for mobile identification in the
immediate area.
- If any cases of signal interference occur in short-range wireless base stations
for mobile identification due to this equipment, either immediately change the
operating frequency band, or stop the transmission of signals, and contact Silex
Technology about possible corrective actions for preventing interference (such as
installation of a partition).
- In addition, if any cases of signal interference occur in low-power wireless base
stations for mobile identification due to this equipment, or if any other problems
occur, contact Silex Technology.
DS/OF2.4 4
2.4 : Indicates wireless equipment using the 2.4 GHz frequency band.
DS/OF : Indicates that DS-SS and OFDM are being used as the modulation scheme.
4 : Indicates that the estimated interference distance is "40 m maximum".
Indicates that all bands are used and the band for mobile identification devices can be
avoided.
*Meaning of the indicators written on the rear panel of the product
Notes When Using 5 GHz Band
- Usage of the 5.2 GHz band (W52/W53) outdoors is prohibited under the Radio Law of
Japan.
For outdoor usage, use the W56 channel only, and do not use the W52/W53 channel.
- For details about environments where recommended antennas besides the standard
supplied antenna can be used, please contact Silex Technology.
Page 21
2. X-5
17
Copyrights for Video and Audio Content
Generally, the permission of the copyright holder is required whenever distributing content
using X-5.
Unauthorized distribution of other people's copyrighted material (content) is prohibited by
law.
Page 22
18
X-5 User's Guide
Page 23
3. X-5 Settings and Installation
19
3-1. Required Items
3.
X-5 Settings and Installation
Transmitter (X-5T) At least one transmitter is required.
Receiver (X-5R / X-5SR) Obtain the required number of receivers for your installation environment. One display
monitor can be connected to one receiver. Also, when using a wired connection, up
to 1000 receivers can be connected to one transmitter, and when using a wireless
connection, up to 32 receivers can be connected to one transmitter.
Note:
The receivers (X-5R / X-5SR) cannot be used as AP.
Media player A media player (or computer) is required that includes a DVI-I (or DVI-D or Analog RGB)
interface and is capable of video output at resolutions supported by X-5.
Note:
X-5 does not support HDCP.
An HDCP-compliant media player cannot be used.
Display monitor [X-5R]
A monitor is required that includes a DVI-I (or DVI-D or Analog RGB) interface and is
capable of display at resolutions supported by X-5 (The number of required monitors
matches the number of receivers).
[X-5SR]
A monitor is required that includes a DVI-D interface and is capable of display at
resolutions supported by X-5 (The number of required monitors matches the number of
receivers).
Obtain the equipment and software below for building the system for X-5.
This section describes the preparation procedures before setting and installation of X-5.
Page 24
20
X-5 User's Guide
Speakers The number of required stereo speakers matches the number of receivers (Speakers are
not required if the display monitor already has built-in speakers).
Display cable [X-5R]
A display cable is required with a DVI-I connector (male to male) and noise suppressor.
The number of required display cables matches the number of transmitters and
receivers.
Also, if connecting to a media player or display monitor with an Analog RGB interface,
a separate adapter (or conversion cable) is also required for converting between the
respective interface and DVI-I.
[X-5SR]
A display cable is required with a DVI-D connector (male to male) and noise suppressor.
The number of required display cables matches the number of transmitters and
receivers.
Audio cable An audio cable is required with a stereo mini-plug connector and noise suppressor. The
number of required audio cables matches the number of transmitters and receivers.
Wireless antenna A wireless antenna is required for both the transmitters (X-5T) and receivers (X-5R).
Although X-5 is supplied with a non-directional antenna, a dedicated directional
wireless antenna (sold separately) must be obtained if a high-performance sending and
receiving environment is required.
Obtain a suitable wireless antenna based on the distance to the receiver, installation
location position, and other factors of the environment where X-5 is installed.
(Only wireless antennas authorized for use by Silex Technology can be used. If a
directional antenna is required, please contact Silex Technology.)
Note:
Mount the wireless antenna by turning the mounting base (screw section) while
grasping the wireless antenna body.
Do not turn the wireless antenna body during or after mounting. If the wireless antenna
needs to be turned, remove the wireless antenna first before turning it.
Note:
The receiver (X-5SR) has a xed antenna. Other antennas cannot be used.
Computer
(for setting)
A computer with a wired LAN port is required for setting X-5.
Network cable
(for setting)
When making the settings, a network cable (category 5e or higher) is required for
connecting the transmitter or receiver with the computer.
- Because X-5 supports Auto MDI/MDI-X, either a straight-through cable or crossover
cable can be used.
- The setting device and computer can be connected directly, or they can be
connected through an Ethernet hub.
Setting software The setting software "SX Smart Finder" is used for setting X-5.
"SX Smart Finder" can be downloaded from the Silex Technology website at the URL
below.
http://www.silexamerica.com/
Page 25
3. X-5 Settings and Installation
21
Connect the audio cables
Use the audio cables to connect the transmitter to the player and the receiver to the
monitor and speakers.
Connect the display cables
Use the display cables to connect the transmitter to the player and the receiver to the
monitor.
Turn on the power
Turn on the power for X-5 (transmitter and receiver), computer, player, monitor, and
speakers.
3-2. Building the Setting Environment
First, connect the cables to X-5 (both transmitter and receiver), and connect the player,
monitor, speakers, and computer. The settings for X-5 are made from a computer by
passing through a wired network.
1.
Connect the network cable
Connect the network cable to X-5 (transmitter and receiver) and the computer.
2.
3.
4.
Start video output for the player
Perform video output from the player.
5.
Page 26
22
X-5 User's Guide
<Example of Connections During Setting Process>
An example of the connections during X-5 setting is shown below.
Transmitter Receiver
Player
Monitor
Setting computer
Network cable
Audio cable Audio cable
Display cable Display cable
Page 27
3. X-5 Settings and Installation
23
3-3. X-5 Settings
Assigning IP Addresses
When the cable connections and power-on sequence are completed, make the network
settings and screen adjustments for X-5 (transmitter and receiver). X-5 is set from the
setting computer.
To simplify the network setting process, X-5 includes an automatic IP address assignment
function. In the factory defaults, the IP address is automatically assigned from the DHCP
server on the network when the power is turned on. If there is no DHCP server on the
network, IP addresses starting from "169.254.xxx.xxx" are automatically assigned so that
there are no duplicate addresses among the devices (Pay careful attention when making
the settings for environments where both wired and wireless networks are used because
duplicate IP addresses may be assigned to devices).
- The setting procedure below is unnecessary if using the automatic IP address assignment function of X-5.
Skip to the next section.
If SX Smart Finder is used to manually assign IP addresses to X-5, perform the procedure
shown below.
1.
Assign a fixed IP address to the computer that will be used to make the settings.
(Example: 10.10.10.10)
2.
When SX Smart Finder is started, the transmitter (X-5T) or receiver (X-5R / X-5SR) is
displayed in the list screen of SX Smart Finder.
Note
- "SX Smart Finder" can be downloaded from the Silex Technology website at the URL below.
http://www.silexamerica.com/
Note
Page 28
24
X-5 User's Guide
4.
In the displayed screen, enter an IP address that is not being used by other network
devices, and click OK.
(Example: 10.3.0.1)
5.
Repeat the above procedure to assign IP addresses to all transmitters and receivers that
do not duplicate the addresses of other network devices.
3.
Select the transmitter or receiver that will be set. From the menu, click Node - Set an IP
address.
- If the Windows firewall is enabled, the screen below is displayed only when SX Smart Finder is started for the first
time. In this screen, check both check boxes and click Allow access (click Unblock in Windows XP and Vista).
TIP
If using Windows Vista, after performing the above operation, the User Account Control window is
displayed, and so click Continue.
Page 29
3. X-5 Settings and Installation
25
Parameter Settings
When assigning of the IP address to X-5 is complete, access the web page of X-5 from the
computer, and set the network parameters. The web page of X-5 can be accessed using SX
Smart Finder.
- The computer that is used for setting must be assigned an IP address that allows communication with X-5.
If the computer cannot access X-5, confirm the IP address of the computer, and if necessary, change the IP
address of the computer.
(Example: If the IP address of X-5 is "169.254.3.111", the computer used for setting must be set to
"169.254.3.1", which is an IP address that is not used by other network devices.
TIP
1.
Start SX Smart Finder, and select the product that will be set.
[Accessing the Web Page]
2.
From the menu, click Node - Web Interface.
3.
Start the web browser, and open the web page of X-5.
- If accessing the configuration page or management page in X-5 web page, a screen is displayed for
entering the password. In the password entry screen, enter "root" for the user name, and enter the root
password assigned to X-5 for the password (nothing is set in the factory defaults).
TIP
Page 30
26
X-5 User's Guide
[Host Name and Password Settings]
In the factory defaults, the host name of X-5 is automatically set from the last six digits
of the Ethernet address. The host name can be used unchanged from its initial value. If
changing the host name, set a name that does not duplicate a name already used by other
network devices.
1.
Click Basic Configuration - Basic from the left-side menu on the web page of X-5.
2.
Set Host Name and Password in the displayed page.
- In the factory defaults, no password is set.
Be sure to always set a password if X-5 is used by connecting to a public network.
TIP
Page 31
3. X-5 Settings and Installation
27
[Video Parameter Settings]
The video parameter settings include Video Interface and Video Mode.
Set Video Interface to match the input signal from the player.
Video Mode is used to set the balance between video smoothness and image quality.
Select the setting value by referring to the table below.
Selection option name Setting description
Custom Operation is performed based on the information set in the "Advanced Configuration"
page.
Movie30 Movie mode is set when you want to give priority to smoothness of motion in the video.
The number in the selection option name is the number of images that are updated per
second.
A larger number results in smoother rendering of the video, but a smaller number
results in a higher image quality. The "Movie30" setting is optimal for distributing video
containing scroll messages. Select either "Movie20" or "Movie15" to give priority to
motion while also keeping a certain level of image quality.
Movie20
Movie15
Picture10 Picture mode is set when you want to give priority to image quality. The number in the
selection option name is the number of seconds that an image is updated.
A larger number results in higher image quality, and a smaller number results in a
reduced communication load.
In particular, the "Picture5" setting is optimal for providing a stable audio quality with
a reduced communication load. To increase the number of updated images, select
"Picture1".
Picture5
Picture3
Picture2
Picture1
Use this setting at its initial setting unless it needs to be changed.
- To enable a certain degree of stable video distribution even in environments with weak signals when
connected to a wireless LAN, select "Movie20" or "Picture1".
Note
Page 32
28
X-5 User's Guide
1.
Click Basic Configuration - Basic from the left-side menu on the web page of X-5.
2.
Set Digital/Analog in the displayed page.
3.
If necessary, set Video Mode.
Page 33
3. X-5 Settings and Installation
29
[Wireless LAN Settings]
When using a wireless LAN, set Wireless Mode to Host or Client, and set the Wireless
Band, SSID, Network Authentication, and other wireless LAN information to match the
installed wireless LAN environment.
1.
Click Basic Configuration - Basic from the left-side menu on the web page of X-5.
An example of the settings when using the transmitter in Host mode is shown below.
Transmitter Receiver
DHCP Disable Disable
IP address Any value Any value (any value where communication
is possible with the transmitter)
Wireless mode Host Client
Wireless band 802.11n/a 802.11n/a
SSID Any character string Any character string (same as transmitter)
Channel bandwidth 40 MHz 40 MHz
Channel Any value -
Sending strength 100% 100%
Network authentication WPA2 WPA2
Encryption system AES AES
Shared key Any value Any value (same as transmitter)
2.
Set the items contained in the Wireless LAN Configuration group in the displayed page.
Depending on the settings made in Wireless LAN Configuration, the displayed group
will change to WEP Configuration, WPA/WPA2 Configuration, or other option, and so
set the items contained in the respective group.
- Be sure to always set encryption if using X-5 by connecting to a wireless network.
- In many cases, the communication bands in the IEEE 802.11b/g and IEEE 802.11n/b/g wireless bands
are already being used due to the widespread use of supported devices, and so in certain cases, it may
not be possible to obtain sufficient communication bandwidth for video transmission. The use of the
IEEE 802.11n/a communication band is recommended for wireless LAN communication in X-5. The
communication band is set in the Channel item of the transmitter.
- If installing for outdoor use, be sure to install in accordance with the stipulated radio wave laws in the
respective country.
Some countries have limitations on the communication bands (channels) that can be used outdoors, and
so caution is needed.
- If W53 (52/56/60/64ch) or W56 (100/104/108/112/116/120/124/128/132/136/140ch) is selected, the
following restrictions apply due to laws and regulations.
- Radar wave detection is performed for one minute before communication is started for each channel.
Communication cannot be performed during this detection period.
- If a radar wave is detected during communication, the channel is automatically detected, and
communication is disconnected.
TIP
Page 34
30
X-5 User's Guide
When entry of a settings group is completed, click the Submit button in the bottom
section of the right side in the web page to save the settings.
[Saving the Settings]
Page 35
3. X-5 Settings and Installation
31
Screen Adjustment
To show video from the player in the optimal state on the display, perform the procedure
below to make screen adjustments.
1.
Output and pause the video from the player connected to the transmitter (output of
a still image is also possible). The output of the video appears nearly completely white
and in full screen.
Use the same operation as in "Parameter Settings" to access the web page of the
transmitter.
2.
Click Management - Video/Audio from the left-side menu on the web page.
3.
Click Start in the Video Auto Adjustment box on the displayed page to execute the
automatic adjustment function of the video signal.
4.
When automatic adjustment is successful, the message below is displayed on the web
page.
- This function is enabled during analog connections.
- Execute this operation only when the display position of the image is shifted.
This operation does not need to be performed if the image is already displayed at a suitable position in the
installed state.
Note
Page 36
32
X-5 User's Guide
The video is distributed from the transmitter to the receiver, and the video that was
output from the player is shown on the display connected to the receiver.
5.
Execute the automatic adjustment function of the display (For details on the automatic
adjustment function of the display, refer to the instruction manual for the display).
6.
This completes the screen adjustment procedure.
If detailed adjustments are necessary, such as for the video contrast and brightness, use
the display's or player's video adjustment function to make the detailed adjustments (For
details on the video adjustment function of the display, refer to the instruction manual for
the display).
Note
- If the video is still not displayed in the optimal state even after performing automatic video adjustment,
use the procedure below to make the setting manually.
For the allowable setting ranges of each setting item, refer to "A-1. List of Setting Items".
1) Click Advanced Configuration - Video/Audio from the left-side menu on the web page.
2) Enter the value for the setting item (such as the phase) of the resolution that will be used in Analog
Resolution Configuration.
3) When the settings are complete, click Submit.
Page 37
3. X-5 Settings and Installation
33
3-4. X-5 Installation
When installing X-5, the network can be connected using either a wired LAN or wireless
LAN. A network environment can also be built that combines both wired and wireless
LANs.
[Device configuration when connecting by a wired LAN]
[Device configuration when connecting by a wireless LAN]
Transmitter
Hub/Switch
Player
Receiver Display
Receiver Display
Receiver Display
Transmitter
Player
Receiver Display
Receiver Display
Receiver Display
Page 38
34
X-5 User's Guide
Characteristics of Supplied Antenna
The antenna supplied with X-5 is a non-directional antenna (omni-directional antenna).
The allowable distance that X-5 can be installed from the antenna for proper operation is a
maximum of 15 meters if a suitable line of sight (described later) is obtained.
- The allowable distance from the antenna for proper operation varies depending on the signal strength
at the installation location. Install at a distance that actually enables stable flow of video when X-5 is
operated.
TIP
- When installing for outdoor use, be sure to install in accordance with the stipulated radio wave laws in the
respective country.
Some countries have limitations on the communication bands and communication methods that can be
used outdoors, and so caution is needed.
TIP
If a wireless LAN is used to build the network, you must understand the characteristics of
the supplied antenna and install X-5 in a favorable signal environment.
Page 39
3. X-5 Settings and Installation
35
Obtaining Line of Sight
Problems may occur in communication using the IEEE 802.11a/n (5 GHz) communication
band due to the effects of barriers and other objects due to the signal characteristics. To
ensure a stable operating environment, obtain a suitable line of sight with the antenna.
[Horizontal line of sight]
[Vertical line of sight]
Receiver
Transmitter
Receiver
Receiver
Transmitter
Transmitter
Page 40
36
X-5 User's Guide
Page 41
4. Video and Audio Distribution and Maintenance
37
4-1. Video and Audio Distribution
4.
Video and Audio Distribution and Maintenance
This chapter describes X-5 operating procedures and maintenance functions provided with
X-5.
In video and audio distribution by X-5, the player connected to the transmitter of X-5 is
used to perform playback only of content. If the setting and installation in the previous
chapter was completed properly, content is played back on the display connected to the
receiver.
If playback of content is stopped (video output to the transmitter is stopped), the standby
screen of X-5 is automatically displayed, and the system waits until playback of content is
started again.
Note
- Once the standby screen is displayed, after a certain amount of time elapses, the video signal is stopped,
and the system switches to sleep mode.
The time until the video signal is stopped can be adjusted in X-5 settings.
Page 42
38
X-5 User's Guide
4-2.
Maintenance Using the Web Interface
Accessing the Web Page of X-5
X-5 environment settings are made by accessing X-5 using a web browser. Access it from a
computer connected to the network environment where X-5 is connected.
The recommended browser settings are shown below.
- Microsoft Internet Explorer 8.0 or later
Note
- The explanations below are based on screen examples when accessing using Internet Explorer 9.0 in
Windows 7. The text displayed in the screens varies depending on the OS and browser version.
- The web page images in the explanations below are based on the web page images of the transmitter.
The displayed information for the receiver may be different.
1.
Start SX Smart Finder, and select the product that will be set.
2.
From the menu, click Node - Web Interface.
Page 43
4. Video and Audio Distribution and Maintenance
39
3.
Start the web browser, and open the web page of X-5.
- If accessing the configuration page, management page, or maintenance page in X-5 web page, a screen
is displayed for entering the password. In the password entry screen, enter "root" for the user name, and
enter the root password assigned to X-5 for the password (nothing is set in the factory defaults).
TIP
Page 44
40
X-5 User's Guide
Status Page
The Status page shows the operating status of X-5.
The various status information can be viewed by selecting the desired menu from the web
page left side.
Page 45
4. Video and Audio Distribution and Maintenance
41
Network Status
This shows the operating status of the wired/wireless LAN of X-5.
Overview
This page shows X-5 services, network operating status, and system information.
Page 46
42
X-5 User's Guide
Video/Audio Status
This shows the video/audio distribution status of X-5.
Page 47
4. Video and Audio Distribution and Maintenance
43
Node Information
This displays a list of the nodes connected in the same network.
Store & Play Status (Receiver Only)
This shows the status of Store & Play function.
Page 48
44
X-5 User's Guide
Configuration Page
The Configuration page is used to make X-5 environment settings.
The Configuration page is divided into Basic Configuration where the basic settings are
made and Advanced Configuration where the advanced settings are made.
An overview of each configuration page is presented below.
For details on each setting item, refer to "Appendix - A-1. List of Setting Items".
To change the settings in the Configuration page, enter the setting information in the
respective page, and click Submit.
Note
- The explanations below are based on the configuration pages for the transmitter. The number of setting
items and setting items vary for the configuration pages for the receiver.
Basic Configuration
Advanced Configuration
Page 49
4. Video and Audio Distribution and Maintenance
45
Basic Configuration
This sets the information required for operating X-5.
Page 50
46
X-5 User's Guide
Advanced Configuration - Device Configuration
(Transmitter)
- Host name and password settings
- Video/audio distribution run/stop
- Retrieving a system time from NTP server
- Synchronizing a system time with the PC via Web browser
The settings below are available.
Page 51
4. Video and Audio Distribution and Maintenance
47
(Receiver)
- Host name and password settings
- Operation priority settings for the multicast distribution feature and Store & Play
feature
- Time setting until stopping of video signal sent to the monitor after video
playback is stopped and the standby screen is displayed
- Retrieving a system time from NTP server
- Synchronizing a system time with the PC via Web browser
The settings below are available.
Page 52
48
X-5 User's Guide
Advanced Configuration - Network Configuration
This sets X-5 network settings.
Page 53
4. Video and Audio Distribution and Maintenance
49
Advanced Configuration - Video/Audio Configuration
This sets the detailed video and audio parameters for X-5.
Page 54
50
X-5 User's Guide
Advanced Configuration - Node Configuration
For the nodes detected on the network by the transmitter, this sets the time until a
communication failure is determined to have occurred in the disconnected node.
(Transmitter)
(Receiver)
This sets the method for connecting to transmitters by receivers.
Page 55
4. Video and Audio Distribution and Maintenance
51
Management Page
Control of remote operation is performed in the Management page.
The various tools can be displayed by selecting the desired menu from the web page left
side.
Page 56
52
X-5 User's Guide
Video/Audio
In the transmitter, the screen automatic adjustment function can be executed.
(Transmitter)
(Receiver)
In the receiver, the image displayed at X-5 startup and the image displayed when video
distribution is stopped can be set.
Page 57
4. Video and Audio Distribution and Maintenance
53
Node Control (Receiver Only)
The transmitter receiving the video distribution can be changed.
Restart
Click Yes to restart X-5.
Page 58
54
X-5 User's Guide
Factory Default
X-5 setting information can be returned to the factory defaults by clicking Yes .
Firmware Update
The firmware in X-5 can be updated to the latest firmware available on the Silex
Technology website (You need to download the latest firmware from the Silex
Technology website first).
Click Browse to select the firmware update file. Click Update to perform the firmware
update process.
Page 59
4. Video and Audio Distribution and Maintenance
55
silex Global Site
Click silex Global Site on the web page left side to open the Silex Technology website.
Page 60
56
X-5 User's Guide
4-3.
Initialization of Settings
This describes how to initialize (reset) X-5 setting information and return to the factory
defaults by using the push switch on X-5.
Initialize X-5 settings to change the settings for X-5 that were previously used on other
networks.
1.
1.
Unplug X-5 from the outlet.
Unplug X-5 from the outlet.
Insert the power plug into the outlet while holding down the push switch on X-5
bottom panel.
Insert the power plug into the outlet while holding down the push switch on the X-5
side panel.
2.
2.
The network port Link LED (orange) and Status LED (yellow) turn on.
If you continue to hold down the push switch, the Link LED changes from orange to
green, and the initialization process is started, and so please release your finger from
the push switch.
The network port Link LED (orange) and Status LED (yellow) turn on.
If you continue to hold down the push switch, the Link LED changes from orange to
green, and the initialization process is started, and so please release your finger from
the push switch.
3.
3.
The initialization process is complete when either the Link LED or Status LED turns off
and then turns on or starts flashing again.
4.
The initialization process is complete when either the Link LED or Status LED turns off
and then turns on or starts flashing again.
4.
[X-5T / X-5R]
[X-5SR]
Page 61
A. Appendix
57
A-1. List of Setting Items
A.
Appendix
Device Configuration
Host Name
TX *
RX *
Web
Basic *
Advanced *
Description Sets the host name.
Allowable setting range
Any character string (up to15 characters)
Default value Prefix ("TX" for transmitter and "RX for receiver) + Last 6 digits of MAC address
Password
TX *
RX *
Web
Basic *
Advanced *
Description Sets the password.
Allowable setting range
Any character string (up to 7 alphanumeric characters or symbols)
Default value None
Operation Mode
TX RX *
Web
Basic Advanced *
Description Sets whether the multicast distribution feature or the Store & Play feature has operation priority.
Allowable setting range
Video Distribution priority / Store & Play priority / Video Distribution only / Store & Play only
Default value Video Distribution priority
Remarks Selecting Store & Play only will enable synchronization among the receivers.
For details, refer to "User's Guide - Store & Play Feature".
Only X-5SR supports the synchronization among the receivers.
Monitor Sleep Timer (sec)
TX RX *
Web
Basic Advanced *
Description Sets the time in seconds until the monitor switches to power-saving mode after video playback is
stopped and the standby screen is displayed.
Allowable setting range
0 (Monitor sleep off) to 1800 (sec)
Default value 10
Some of the setting items below may apply only to transmitters or receivers (In the tables, "TX"
and "RX" are used to indicate whether the item applies to transmitters and receivers, respectively).
Page 62
58
X-5 User's Guide
Continuation of Device Configuration
Video/Audio
TX *
RX -
Web
Basic -
Advanced *
Description Sets the video/audio import operation mode.
Allowable setting range
Video/Audio dependent / Video only / Video/Audio independent / Video/Audio disabled
Default value Video/Audio dependent
NTP
NTP Time Synchronization
TX *
RX
*
Web
Basic -
Advanced *
Description Enables/Disables the time synchronization using the NTP feature.
Allowable setting range
Enable / Disable
Default value Disable
NTP Server Name
TX *
RX *
Web
Basic -
Advanced *
Description Sets the host name or IP address of the NTP server.
Allowable setting range
Any string (up to 63 characters) or IP address (0.0.0.0 - 255.255.255.255)
Default value None
Page 63
A. Appendix
59
Time
Local Time Zone
TX *
RX
*
Web
Basic -
Advanced *
Description Sets the time zone.
Allowable setting range
-12:00 to +12:00 (on an hourly basis)
Default value 0:00
System Time
TX *
RX *
Web
Basic -
Advanced *
Description Synchronizes the equipment system time with the sending time by the web browser
Allowable setting range
*A fixed value cannot be set. This only allows synchronizing with the sending time by the web
browser.
Default value Undetermined (For details, see the Remarks field.)
Remarks The system time will stop if the main unit power remains off for a prolonged period of time and
the internal battery for storing the system time runs out of power. If the battery runs out of power,
the time that the battery ran out of power is stored as the system time until the main unit power is
turned on again and the battery for storing the system time is charged.
Browser Time
TX *
RX *
Web
Basic -
Advanced *
Description Shows the system time of the PC which the Web browser is opened on.
Allowable setting range
*A fixed value cannot be set.
Default value Undetermined
Page 64
60
X-5 User's Guide
Wired LAN Settings
DHCP
TX *
RX *
Web
Basic *
Advanced *
Description Selects whether IP address setting by DHCP is used.
Allowable setting range
Enable / Disable
Default value Enable
IP Address
TX *
RX *
Web
Basic *
Advanced *
Description Sets the IP address.
Allowable setting range
0.0.0.0 to 255.255.255.255
Default value 0.0.0.0
Subnet Mask
TX *
RX *
Web
Basic -
Advanced *
Description Sets the subnet mask.
Allowable setting range
0.0.0.0 to 255.255.255.255
Default value 0.0.0.0
Default Gateway
TX *
RX *
Web
Basic -
Advanced *
Description Sets the default gateway address.
Allowable setting range
0.0.0.0 to 255.255.255.255
Default value 0.0.0.0
Page 65
A. Appendix
61
Wireless LAN Settings
DHCP
TX *
RX *
Web
Basic *
Advanced *
Description Selects whether IP address setting by DHCP is used.
Allowable setting range
Enable / Disable
Default value Disable
IP Address
TX *
RX *
Web
Basic *
Advanced *
Description Sets the IP address.
Allowable setting range
0.0.0.0 to 255.255.255.255
Default value 10.x.x.x (Automatically generated from MAC address in wired LAN)
Subnet Mask
TX *
RX *
Web
Basic Advanced *
Description Sets the subnet mask.
Allowable setting range
0.0.0.0 to 255.255.255.255
Default value 0.0.0.0
Default Gateway
TX *
RX *
Web
Basic Advanced *
Description Sets the default gateway address.
Allowable setting range
0.0.0.0 to 255.255.255.255
Default value 0.0.0.0
Wireless Mode
TX *
RX *
Web
Basic *
Advanced *
Description Sets whether the wireless LAN operates as an access point or client device.
Allowable setting range
Disable (Wireless LAN is not used)/ Host (Access point)/ Client (Client device)
Default value Disable
Wireless Band
TX *
RX *
Web
Basic *
Advanced *
Description The frequency band used in the wireless LAN is selected from the wireless LAN types.
Allowable setting range
802.11b/g, 802.11a, 802.11n/b/g, 802.11n/a
Default value 802.11n/a
Page 66
62
X-5 User's Guide
Continuation of Wireless LAN Settings
Channel Bandwidth
TX *
RX *
Web
Basic Advanced *
Description Selects the bandwidth used when operating at IEEE 802.11n.
Allowable setting range
20 MHz / 40 MHz
Default value 40 MHz
Remarks This is enabled only when "802.11n/b/g" or "802.11n/a" is selected in the setting item "Wireless
Band".
Channel
TX *
RX
*
Web
Basic *
Advanced *
Description Selects the wireless channel.
Allowable setting range
The channels that can be set vary depending on the country.
1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11,
36, 40, 44, 48,
52, 56, 60, 64,
149, 153, 157, 161, 165
Default value 36
Transmit Power
TX *
RX *
Web
Basic
*
Advanced *
Description Selects the transmission strength of the wireless LAN.
Allowable setting range
100% / 50% / 25% / 12%
Default value 100%
Remarks Changes the setting when you want to reduce signal interference to other wireless networks.
SSID
TX *
RX *
Web
Basic *
Advanced *
Description Sets the SSID.
Allowable setting range
Any character string (maximum of 32 characters)
Default value SILEX X-5
SSID Broadcast
TX *
RX *
Web
Basic Advanced *
Description Selects whether an SSID broadcast is performed.
Allowable setting range
OFF/ON
Default value ON
Page 67
A. Appendix
63
Continuation of Wireless LAN Settings
a/g Multicast Rate
TX *
RX *
Web
Basic -
Advanced *
Description Sets the transmission rate when "802.11b/g" or "802.11a" is set for "Wireless Band".
Allowable setting range
6Mbps / 9Mbps / 12Mbps / 18Mbps / 24Mbps / 36Mbps / 48Mbps / 54Mbps
Default value 36Mbps
Remarks This is enabled only when "802.11b/g" or "802.11a" is selected for the "Wireless Band" setting.
n 20MHz Multicast Rate
TX *
RX *
Web
Basic -
Advanced *
Description Sets the transmission rate when "Wireless Band" is set to "802.11n/b/g" or "802.11n/a" and "Channel
Bandwidth" is set to "20MHz".
Allowable setting range
S 6.5Mbps / S 19.5Mbps / S 58.5Mbps / S 65Mbps /
D 13Mbps / D 26Mbps /D 39Mbps / D 52Mbps / D 78Mbps / D 104Mbps /
D 117Mbps / D 130Mbps
Default value D 104Mbps
Remarks This is enabled only when "802.11n/b/g" or "802.11n/a" is selected in the "Wireless Band" setting
and "20MHz" is selected in the "Channel Bandwidth" setting.
n 40MHz Multicast Rate
TX *
RX *
Web
Basic -
Advanced *
Description Sets the transmission rate when "Wireless Band" is set to "802.11n/b/g" or "802.11n/a" and "Channel
Bandwidth" is set to "40MHz".
Allowable setting range
S 13.5Mbps / S 40.5Mbps / S 121.5Mbps / S 135Mbps /
D 27Mbps / D 54Mbps / D 81Mbps / D 108Mbps / D 162Mbps / D 216Mbps /
D 243Mbps / D 270Mbps
Default value D 108Mbps
Remarks This is enabled only when "802.11n/b/g" or "802.11n/a" is selected in the "Wireless Band" setting
and "40MHz" is selected in the "Channel Bandwidth" setting.
Network Authentication
TX *
RX *
Web
Basic *
Advanced *
Description Selects the authentication method.
Allowable setting range
Open / Shared / WPA / WPA2 / WPA MIX
Default value WPA2
Page 68
64
X-5 User's Guide
Wireless LAN Settings - WEP Configuration
WEP
TX *
RX *
Web
Basic
*
Advanced *
Description Selects whether WEP is used.
Allowable setting range
OFF / ON
Default value OFF
Key Index
TX *
RX *
Web
Basic
*
Advanced *
Description Selects the WEP key index.
Allowable setting range
1 to 4
Default value 1
WEP Key1-4
TX *
RX *
Web
Basic *
Advanced *
Description Sets the WEP key.
Allowable setting range
A hex character string (hexadecimal notation) or ASCII character string can be set.
For a 64-bit key, 10 hexadecimal digits or 5 ASCII characters can be used. For a 128-bit key, 26
hexadecimal digits or 13 ASCII characters can be used. The hexadecimal number and ASCII
character string are distinguished based on the character string length.
Default value
None
Remarks WEP Key1 only can be set in the Web Basic Configuration screen.
Wireless LAN Settings - WPA/WPA2 Configuration
WPA Encryption Mode
TX *
RX *
Web
Basic *
Advanced *
Description Selects the WPA encryption mode.
Allowable setting range
TKIP / AES / AUTO
Default value AES
Pre-Shared Key
TX *
RX *
Web
Basic *
Advanced *
Description Sets the pre-shared key.
Allowable setting range
Any character string (8 to 63 characters. However, for hexadecimal numbers, the string can be from
8 to 64 characters.)
Default value silex technology, Inc.
Page 69
A. Appendix
65
Common
DNS Server (Primary)
TX *
RX
*
Web
Basic -
Advanced *
Description Sets the primary DNS server address.
Allowable setting range
0.0.0.0 to 255.255.255.255
Default value 0.0.0.0
DNS Server (Secondary)
TX *
RX *
Web
Basic -
Advanced *
Description Sets the secondary DNS server address.
Allowable setting range
0.0.0.0 to 255.255.255.255
Default value 0.0.0.0
Page 70
66
X-5 User's Guide
Video Configuration
Video Mode
TX *
RX -
Web
Basic *
Advanced -
Description Sets the balance between video smoothness and image quality.
Allowable setting range
Movie30 / Movie20 / Movie15 / Picture10 / Picture5 / Picture3 / Picture2 / Picture1 / Custom
Default value Movie30
Remarks If Custom is set for this setting in Basic Configuration, the video parameters must be set in
Advanced Configuration.
Digital/Analog Mode
TX *
RX -
Web
Basic *
Advanced *
Description
This is set to match the input signal from the player.
Allowable setting range
Digital / Analog
Default value Digital
Analog Input
TX *
RX -
Web
Basic Advanced *
Description Selects the method for recognizing the analog video signal.
Allowable setting range
mode1 (PC mode)/mode2 (TV mode)
Default value mode1
Remarks Differences between methods for recognizing the analog video signal
mode1 (PC mode)
- Video at analog 640x480 and 720x480 are both run at 640x480.
mode2 (TV mode)
- Video at analog 640x480 and 720x480 are both run at 720x480.
Codec Size (KB)
TX *
RX -
Web
Basic Advanced *
Description Sets the image size (image quality) used per video frame.
Allowable setting range
32 to 1024 (KByte)
Default value 168
Frame Rate
TX *
RX -
Web
Basic Advanced *
Description Sets the frame rate of the video being distributed.
Allowable setting range
30fps / 20fps / 15fps / 10fps / 5fps / 3fps / 2fps / 1fps
Default value 30fps
Page 71
A. Appendix
67
Continuation of Video Configuration
Video/Audio Recovery Level
TX *
RX -
Web
Basic Advanced *
Description Sets the level for compensating for any network data loss in video/audio distribution.
A larger value enables fewer breaks in video/audio distribution due to data loss. On the other hand,
a smaller value reduces the video/audio delay time, but in a wireless environment, this can increase
the likelihood that a break occurs in the distribution. Normally, use at the default value.
Allowable setting range
0 to 3
Default value 3
Video Configuration - Analog Resolution Adjustment
H.Position
TX *
RX -
Web
Basic Advanced *
Description Sets the horizontal direction of the video capture position for each resolution.
A smaller value moves the position to the left, and a larger value moves the position to the right.
Allowable setting range
-100 to 100
Default value 0
V.Position
TX *
RX -
Web
Basic Advanced *
Description Sets the vertical direction of the video capture position for each resolution.
A smaller value moves the position upward, and a larger value moves the position downward.
Allowable setting range
-50 to 50
Default value 0
Clock
TX *
RX -
Web
Basic Advanced *
Description Sets the sampling frequency of the video signal.
Allowable setting range
-128 to 127
Default value 0
Phase
TX *
RX -
Web
Basic Advanced *
Description Changes the phase of the clock that samples the video signal.
Allowable setting range
0 to 31
Default value 0
Page 72
68
X-5 User's Guide
Audio Configuration
Volume
TX *
RX -
Web
Basic -
Advanced *
Description Sets the audio volume (recording volume).
Allowable setting range
0 (mute) to 45
Default value 23
Node Configuration
Node Expiration Time (sec)
TX *
RX -
Web
Basic -
Advanced *
Description Sets the expiration time of the node where communication was disconnected.
Allowable setting range
AUTO / 60 / 300 / 1800 / 3600
Default value AUTO
Node List Method
TX -
RX *
Web
Basic -
Advanced *
Description Selects the node detection method.
Allowable setting range
Dynamic(Multicast) / Dynamic(Unicast) / Static
Default value Dynamic(Multicast)
Remarks If "Static" was selected, Static Node0 - 7 must also be set.
Static Node 0-7
TX -
RX *
Web
Basic -
Advanced *
Description Sets the IP address when Static Node is selected.
Allowable setting range
0.0.0.0 to 255.255.255.255
Default value 0.0.0.0
Loading...