Silex Technology TROY200 User Manual

WirelessrPr

TROY 200

err

ntt

iin

uii

err

Document Version: 1.2 (April, 2004)

P/N: 9560NT00A0

All trademark and trade names are the properties of their respective owners.

Table of Contents

Chapter 1 Introduction 1

Features......................................................................................................................... 1

Safety Instructions ........................................................................................................ 2

Package Contents.......................................................................................................... 2

Physical Details ............................................................................................................3

Chapter 2 LAN Installation 5

Procedure......................................................................................................................5

Chapter 3 Wireless Print Server Configuration 7

Overview ......................................................................................................................7

Using the Windows Wizard.......................................................................................... 7

Chapter 4 Client PC Configuration 10

Overview ....................................................................................................................10

Windows Peer-to-peer Printing ..................................................................................12

Windows SMB Printing.............................................................................................. 19

Windows with Server-based Print Queues .................................................................21

Macintosh (AppleTalk)............................................................................................... 22

Macintosh OS X .........................................................................................................23

Chapter 5 BiAdmin Management Utility 24

Requirements..............................................................................................................24

Installation .................................................................................................................. 24

Operation .................................................................................................................... 24

Chapter 6 Web-Based Management 39

Overview ....................................................................................................................39

Preparation.................................................................................................................. 39

Connecting to the WPS-0104 LevelOne Wireless Printer Server............................... 40

Configuration Screens ................................................................................................40

Chapter 7 Special Features 47

Overview ....................................................................................................................47

Internet Printing Protocol (IPP)..................................................................................47

Internet Mail Printing .................................................................................................52

Printing through the Internet....................................................................................... 56

Page i

Chapter 8 Troubleshooting 57

Overview ....................................................................................................................57

Hardware & Connection Problems.............................................................................57

AppleTalk (Macintosh)............................................................................................... 58

Windows Printing Problems.......................................................................................60

Unix Troubleshooting................................................................................................. 65

Appendix A Specifications 66

General Specifications................................................................................................66

Protocol Support.........................................................................................................66

Feature Support........................................................................................................... 66

Regulatory Approvals................................................................................................. 67

Appendix B Windows Server Configuration 69

Windows NT4.0 Server .............................................................................................. 69

Windows 2000/2003 Server .......................................................................................70

Appendix C Unix Systems 71

Overview ....................................................................................................................71

WPS-0104 LevelOne Wireless Printer Server IP Address Configuration.................. 71

Other WPS-0104 LevelOne Wireless Printer Server Configuration........................... 72

LPD Configuration ..................................................................................................... 73

Appendix D NetWare 78

Overview ....................................................................................................................78

Creating an NDPS Manager Object............................................................................ 78

Creating an NDPS Printer Agent................................................................................ 79

Page ii

Chapter 1

Introduction

This chapter provides an overview of your WPS-0104 LevelOne Wireless Printer Server's features.

Features

Congratulations on the purchase of your new WPS-0104 LevelOne Wireless Printer Server. Your WPS-0104 LevelOne Wireless Printer Server was designed to provide a simple and efficient network printing solution. It is packed with features, including:



Wireless LAN Support. Wireless stations supporting the IEEE 802.11b or IEEE

802.11g standard can interoperate with the WPS-0104 LevelOne Wireless Printer Server. Both LAN and WLAN users can print to the attached printer or printers.

Versatility. The WPS-0104 LevelOne Wireless Printer Server supports up to four



protocols: TCP/IP, SMB (Service Message Block), AppleTalk (EtherTalk), and NetBEUI. It features an Ethernet interface port and operating system support includes Unix, NetWare (NDPS LPR printing), and Microsoft Windows.

Easy Installation. The WPS-0104 LevelOne Wireless Printer Server makes adding



printers or plotters to your network simple.

Easy Setup. A number of utility programs are supplied to simplify setup. For Windows



98SE/Me/NT/2000/XP/2003 Server users, the BiAdmin program makes it easy to configure the WPS-0104 LevelOne Wireless Printer Server for a variety of network and server configurations.

Web-based Interface. The Web-based interface provides an easy method of



configuration in TCP/IP networks, regardless of your client platform.

Compact Size. This allows the WPS-0104 LevelOne Wireless Printer Server to be used



even where space is limited.

Remote Management Tools. A variety of software tools are provided. In most



environments, both the WPS-0104 LevelOne Wireless Printer Server and attached bidirectional printers can be configured remotely.

 Internet Printing Protocol (IPP) Support. The WPS-0104 LevelOne Wireless Printer

Server can act as an IPP (Internet Printing Protocol) Server, allowing clients, suppliers, colleagues and others to print to your printer from anywhere on the Internet. Windows IPP Client software is also supplied.

Page 1

Safety Instructions

For your own safety, and to protect your WPS-0104 LevelOne Wireless Printer Server, please observe the following safety advice.

1. Unplug this device from its power source before cleaning. Use only a slightly dampened cloth for cleaning. Do not use liquid or aerosol cleaners.

2. Avoid using this product near water. Exposure to water poses an electric-shock hazard.

3. Do not place the WPS-0104 LevelOne Wireless Printer Server on an unstable surface. The device may fall causing serious damage to the device.

4. This device should only be used with the power supply type specified on the marking label. If you are not sure of type of your local power supply, consult your dealer or the local power company.

5. Do not pinch, crimp or otherwise damage the power cord. If exposed to foot traffic, ensures that the cable is properly shielded and does not pose a tripping hazard.

6. If using an extension cord, makes sure the total ampere rating of the products using the cord does not exceed the extension cord's ampere rating.

7. Do not attempt to service this device, as opening or removing casing may expose you to dangerous voltage points or other risks. Refer all servicing to qualified service personnel.

8. The WPS-0104 LevelOne Wireless Printer Server should be serviced by qualified service personnel under the following conditions:

• The power cord is damaged or frayed.

• Liquid has been spilled onto the product.

• The product has been exposed to rain or water.

• The product does not operate normally in accordance with the operating instructions.

• The device has been dropped or the casing has been damaged.

Package Contents

You should find the following items packaged with your WPS-0104 LevelOne Wireless Printer Server. If any items are missing, contact your dealer immediately.

• The WPS-0104 LevelOne Wireless Printer Server.

• Power Adapter.

• One CD-ROM containing all support programs and this manual.

• Quick Install Guide.

Page 2

Physical Details

This section has details of the LEDs and connectors. Further details are contained in Appendix A - Specifications.

WPS-0104 LevelOne Wireless Printer Server

• 1 x USB 2.0 Printer Port

• IEEE 802.11g/802.11b Wireless Station

• 10/100BaseT LAN connection

Figure 1: WPS-0104

Item Description

Error LED

Status LED

USB Connector

10/100BaseT Connector.

Power input

Diagnostic button, see page 4 for details.

Page 3

LED Indicators

There are two (2) LED indicators on the top panel - Status (Green, right) and Error (Red, left). The LED indicator modes are described in the following table.

Status LED Error LED Status Description

Off Off No Power

On On Hardware error

On Off Normal operation (idle)

Blinking Off Normal operation - data is being transmitted or

received on the USB Printer Port.

Blinking Blinking During a Firmware Upgrade, both LEDs will blink.

Diagnostic Push Button

The WPS-0104 LevelOne Wireless Printer Server is fitted with a Diagnostic Push Button. The button is recessed; a pin or paper clip can be used to press it. This button has 2 functions:

• Restore the factory default settings

• Print a test page containing all current settings.

To restore the factory default settings:

1. Turn the WPS-0104 LevelOne Wireless Printer Server OFF.

2. Press and hold the diagnostic button. While pressing the button, switch the WPS-0104 LevelOne Wireless Printer Server ON.

3. If you continue pressing the button for 10 seconds, a diagnostic page will be printed, showing the new (default) settings.

To generate a Diagnostic print out

1. Ensure that both the WPS-0104 LevelOne Wireless Printer Server and the printer attached to port 1 are ON.

2. Press the diagnostic button, and hold it in for 2 seconds.

3. The test page, containing the current settings, will be printed.

Note:

PostScript printers are unable to print this page. If you have a PostScript printer on Port 1, the test page will not be printed.

Page 4

Chapter 2

LAN Installation

This chapter describes how to install the WPS-0104 LevelOne Wireless Printer Server in your Local Area Network.

Procedure

1. Preparation

• Ensure the power is OFF. Do not connect the WPS-0104 LevelOne Wireless Printer

Server while power is On.

• Find the Default Server Name for your WPS-0104 LevelOne Wireless Printer Server. The

Default Server Name is shown on a sticker on the base of the device. It consists of 8 letters

and/or digits. Record this name; it may be needed during configuration.

2. Connect the Printer or Printers

Connect the printer or plotter cable(s) to the appropriate port(s) on the WPS-0104 LevelOne Wireless Printer Server unit.

3. Connect to your Network

Wired Network Interface

Connect the network cable to the 10/100BaseT LAN connector on the WPS-0104 LevelOne Wireless Printer Server.

• To use the LAN interface, the LAN cable needs to be inserted

BEFORE powering ON

• In the default Wireless "Infrastructure" mode, connecting a LAN cable

Wireless Network Interface

Ensure that your Access Point is compatible with the WPS-0104 LevelOne Wireless Printer Server's default settings:

SSID

WEP

will disable the Wireless interface. To use both the LAN and Wireless interfaces, the Wireless mode must be changed to "Ad-hoc".

Null (blank)

The WPS-0104 LevelOne Wireless Printer Server will adopt the SSID used by the Access Point, unless the Access Point is configured not to broadcast its SSID.

Disabled.

Because the default Wireless mode is "Infrastructure", you cannot configure the WPS-0104 LevelOne Wireless Printer Server via the Wireless interface unless you have an Access Point.

Page 5

LAN Installation

4. Power Up

Plug in the power adapter cable and power up. Start-up will take only a few seconds.

Use only the Power Supply unit provided with the device. Power Supply units for different models are not interchangeable.

5. Check the LEDs

Once start-up is complete:

• The Status LED should be On.

• The Error LED should be Off.

Page 6

Chapter 3

Wireless Print Server

Configuration

This chapter provides an overview of the configuration process.

Overview

The WPS-0104 LevelOne Wireless Printer Server is designed to support many different platforms, and the configuration required would depend upon the environment in which it is installed.

• The WPS-0104 LevelOne Wireless Printer Server usually requires configuration, but if

there's a DHCP server on your network, then the device is just plug-and-play. A Windowsbased setup Wizard is also provided on the CD-ROM to simplify this task.

• PCs wishing to use the printer attached to the WPS-0104 LevelOne Wireless Printer

Server always require configuration. See Chapter 4- Client Configuration for details.

• If you wish to use a queue-based printing system using Windows NT Server/Windows

2000/Windows XP, the Network Server must be configured as detailed in Appendix B -

Windows Server Configuration. However, it is not necessary to use a Network Serverbased queue; client PCs can print directly to the WPS-0104 LevelOne Wireless Printer Server using the Peer-to-peer Printing installed by the User setup option on the CD-ROM.

Configuration Methods

The following methods are available to perform the required Print Server configuration:

• Windows-based Wizard - see below for details.

• BiAdmin management utility program - see Chapter 5 for details.

• Web-based setup - see Chapter 6 for details.

Advanced Configuration and Management

The BiAdmin management utility is provided for advanced configuration and management. This program is installed by default when the Administrator install option is chosen. See Chapter 5 for details on using BiAdmin.

Using the Windows Wizard

The Windows-based Wizard is supplied on the CD-ROM, and runs on Windows 98SE, NT4.0, ME, Windows 2000, Windows XP and Windows Server 2003.

Using this Wizard is the recommended method to configure the Print Server.

It can be used configure the WPS-0104 LevelOne Wireless Printer Server for your Network environment, even if the Print Server does not have a valid IP address.

Procedure

1. Insert the supplied CD-ROM into your drive. If the setup program does not start automatically, run SETUP.exe in the root folder.

2. On the first screen, shown below, click Setup Wizard.

Page 7

Figure 2: WPS-0104 LevelOne Wireless Printer Server Screen

3. Click Next on the first screen of the Wizard, to view a list of WPS-0104 LevelOne Wireless Printer Servers on your LAN.

4. Select your new WPS-0104 LevelOne Wireless Printer Server, then click Next to continue.

5. Enter the required data on the following screen.

• Name of the Print Server can be changed if you wish.

• Comment is optional.

• Select or enter the Workgroup name for this WPS-0104 LevelOne Wireless Printer

Server.

6. Click Next to configure the TCP/IP Screen:

• Select Obtain IP Address automatically if your LAN has a DHCP Server, otherwise

select Fixed IP Address.

• For Fixed IP Address, enter an unused address from the range used on your LAN, or

click the Suggest New Values Button. Use the same Network Mask and Gateway as PCs on your LAN.

7. On the Wireless Screens, the settings should be set to match your other Wireless Stations. For details about each setting, refer to the following section Wireless Configuration.

8. Click Finish to save the data to the WPS-0104 LevelOne Wireless Printer Server.

Note: To install the Wizard on your PC, use the "Installation" option.

If the desired WPS-0104 LevelOne Wireless Printer Server is not listed:

• Check all cables to the WPS-0104 LevelOne Wireless Printer Server.

• Check that the WPS-0104 LevelOne Wireless Printer Server's Error LED is Off. If it is

On, restart the Print Server.

• Check that your PC and the WPS-0104 LevelOne Wireless Printer Server are on the same

LAN segment. (If you don't have a Router or Gateway on your LAN, you only have 1 segment.)

• Check that your PC has either the TCP/IP or NetBEUI network protocols installed. See

Checking your Network Protocols in Chapter 4for details.

Page 8

Wireless Configuration

Wireless Mode

The WPS-0104 LevelOne Wireless Printer Server is a Wireless station, NOT an access point. Like other Wireless stations, they have 2 modes:

• Ad-Hoc mode - no Access Point is used, Wireless stations communicate directly with

each other. Each Wireless station should be set to use the same Channel, although some Wireless stations will scan all channels to find compatible ad-hoc groups they can join

• Infrastructure (Default) - all Wireless stations connect to the Access Point. This allows

connection to both other Wireless stations and the wired LAN.

To use both the LAN and Wireless interfaces, the Wireless mode must be set to "Ad-hoc". In "Infrastructure" mode, connecting a LAN cable will disable the Wireless interface.

Required Configuration

Ad-hoc Mode Infrastructure Mode

SSID

Channel

WEP Settings

The 802.11g Wireless Print Server will

Must match the Access Point.

join any group with the same SSID.

If there's no Ad-Hoc group available, the 802.11g Wireless Print Server will create the group using the SSID assigned to it.

The 802.11g Wireless Print Server will join any group with the same Channel number.

If there is no existing Ad-Hoc group available, the 802.11g Wireless Print

Access Point sets the Channel used.

Wireless stations automatically locate the

correct channel. Server will create the group using its own Channel number.

Must match the other Wireless stations. Must match the Access Point.

Page 9

Chapter 4

Client PC Configuration

The chapter details the client configuration required on LAN clients to use the printer or printers attached to the WPS-0104 LevelOne Wireless Printer Server.

Overview

Before performing client configuration, the WPS-0104 LevelOne Wireless Printer Server must be installed on your LAN, and configured as described in Chapter 3. Both the WPS-0104 LevelOne Wireless Printer Server and the attached printer must be powered ON.

Printing Methods

The WPS-0104 LevelOne Wireless Printer Server supports a number of printing methods:

• Peer-to-peer Printing means that the print jobs are stored (queued) on your PC, and sent

directly to the WPS-0104 LevelOne Wireless Printer Server when it is available.

• Server-based Print Queue means that all print jobs are stored (queued) on the Network

Server (e.g. Windows NT/2000) and then sent to the WPS-0104 LevelOne Wireless Printer Server. This allows the Network Administrator to modify the Print Queue. For example, an important job can be moved to the head of the queue.

• Windows SMB printing is a Microsoft standard for using a "Network Printer". No

additional software needs to be installed on your Windows PC, and printing from MSDOS programs is supported. However, because the WPS-0104 LevelOne Wireless Printer Server can not store files, large print jobs may cause problems.

• AppleTalk is also supported, and normally no configuration of the WPS-0104 LevelOne

Wireless Printer Server is required. See the Macintosh section of this chapter for details of client configuration.

Which printing method should I use?

• If using Windows 98SE, NT, Me, 2000, or XP, the easiest method to use is Peer-to-peer

Printing.

• If using Windows, and you need to print from MS-DOS programs, or you don't wish to

install additional software, use SMB. However, SMB is not suitable for large, complex documents, so if you need this as well as MS-DOS printing, you should install BOTH Peer-to-peer Printing and SMB printing. MSDOS programs can use the SMB printer, Windows programs should use Peer-to-peer Printing.

• If your LAN has Network Servers (e.g. Windows NT, Windows 2000 Server) use the

method advised by your Network Administrator. The WPS-0104 LevelOne Wireless Printer Server can print via a queue located on a Network server, if desired.

• Unix users - refer to Appendix C.

• Macintosh users - refer to the Macintosh section of this chapter.

Page 10

Checking your Network Protocols (Windows 9x)

Your PC must have EITHER the TCP/IP or NetBEUI protocols installed.

• If using the Peer-to-peer Printing, the installation program will check this for you.

• If using other methods, you must check manually, as follows:

1. Select the Settings - Control Panel - Network option on the Start Menu. You should see a screen like the one following:

Figure 3: Network Configuration

• The top line in the list (NetBEUI -> PCI Fast Ethernet Adapter) indicates that the

NetBEUI protocol is installed on this PC. Your PC will show the name of the your Network card rather than "PCI Fast Ethernet Adapter".

• The highlighted line (TCP/IP -> PCI Fast Ethernet Adapter) indicates that TCP/IP is

installed. Your PC will show the name of the your Network card rather than "PCI Fast Ethernet Adapter".

2. If neither line is present:

• Install the NetBEUI protocol by selecting Add - Protocol - Microsoft - NetBEUI - OK.

You may be prompted for your Windows CD-ROM. This protocol requires no configuration.

• If required, you can also install TCP/IP. However, depending on your LAN

environment, TCP/IP may require further configuration.

3. If either protocol is already installed, proceed with installation.

Page 11

Windows Peer-to-peer Printing

With this printing method, print jobs are stored (queued) on your PC, and then sent to the WPS-0104 LevelOne Wireless Printer Server when it is available.

Figure 4: Peer-to-Peer Printing

Windows 2000 & XP require no additional software.

For other versions of Windows, the supplied PTP (Peer-to-Peer) Printer Port software must be installed on each PC.

Windows 2000/XP Setup

The recommended printing method is to use LPR, as follows:

1. Open your Printers folder, right-click the desired printer and select Properties.

2. Select the Ports tab and click the Add Port button.

Figure 5: Printer Ports Screen

Page 12

3. Choose Standard TCP/IP Port, then click New Port.

Figure 6: Add Port Screen

4. On the Add Standard TCP/IP Printer Port screen above, enter the IP Address of the Print Server in the Printer Name or IP Address field, then click Next.

Figure 7: Additional Port Information Screen

5. On this screen, select Custom, and click the Settings button.

Page 13

Figure 8: Port Settings Screen

6. On the Port Settings screen, shown above:

• Select LPR in the Protocol section

• Enter a Queue name (L1 for the USB Port)

• Ensure the LPR Byte Counting Enabled setting is Enabled.

• Click OK to confirm your changes and close this screen.

7. Follow the prompts to complete the Wizard.

Page 14

Windows 9x/ME Setup

Before performing the following procedure, the WPS-0104 LevelOne Wireless Printer Server must be installed on your LAN, and configured as described in Chapter 3. Both the WPS-0104 LevelOne Wireless Printer Server and the attached printer should be powered ON.

1. Insert the supplied CD-ROM into your drive. If the setup program does not start, run SETUP.exe in the root folder.

2. Click Installation button, then select the User Install.

Figure 9: Installation Screen

3. Follow the prompts to complete the installation of the Peer-to-peer Printer Port Driver. (Refer to the Windows section of Chapter 8 - Troubleshooting if there is a problem with the installation.)

4. The Print Driver Setup will then run.

In future, you can use Start - Programs - PrintServer Driver - Printer Port Setup to run the program again.

PTP Printer Port Setup

1. The program will search for Printer Servers on the network, and a screen like the following will be displayed.

• If desired, click Refresh.

• The name of the attached printer will be displayed if possible. If "No printer" is

displayed, check that the printer is properly connected and powered on.

Page 15

Figure 10: Print Port Setup (Peer-to-peer Printing)

If your WPS-0104 LevelOne Wireless Printer Server is not listed:

• Click the "Refresh" button.

• Check that both the WPS-0104 LevelOne Wireless Printer Server and the

printer are properly connected, and powered on.

• Check that the WPS-0104 LevelOne Wireless Printer Server has been

configured. (Use the Setup Wizard on the CD-ROM.)

• If using TCP/IP, try installing the NetBEUI protocol. (See the earlier section

Checking your Network Protocols for details.). Then try again.

2. Select the desired port on a WPS-0104 LevelOne Wireless Printer Server, then click Next. A pop-up message will inform you if the port has been created successfully.

If you see the following error message, either install Internet Explorer 4 or later, or follow the procedure in the "Trouble Shooting - Windows" section of Chapter 8.

3. The printer port will be created, then a screen like the following will be displayed.

Page 16

Figure 11: Configure Printer Port

4. Select the correct Windows printer in the Existing Printers list, and click the Connect button.

If the correct printer type is not listed, click "Add New Printer" to run the Windows Add Printer wizard. Step through the Wizard and install the required printer:

• Select the correct Printer Manufacturer and Model, or use the "Have Disk" option if

appropriate.

• We recommend changing the Printer name to indicate which device is on.

(e.g. HP2100 on SCA43600_P1)

• If prompted about Sharing the printer, do NOT enable Sharing.

• When the Printer installation is finished, it will be listed in the Configure Printer Port

screen above. Select it and click Connect.

5. Installation is now complete. You can now print using this printer.

• To install additional Printers, repeat steps 4.

• Use the Start menu to run this program in future. The default installation is Start -

Programs - PrintServer Driver - Print Driver Setup.

Note:

If using the Epson Spooler Manager, this program must be disabled, as follows:

1. Run the Epson Spooler Manager.

2. Select "Queue Setup" from the menu.

3. Click "Use Print Manager for this port".

4. Click "OK" to exit.

Management

• Print jobs can be managed like any Windows printer. Open the Printers folder (Start -

Settings - Printers) and double-click any printer to see the current print jobs.

• If the printer attached to the WPS-0104 LevelOne Wireless Printer Server is changed, just

run this program again, and select the correct printer.

• To delete a port created by this setup program, use the Windows Delete Port facility:

• Right-click any printer in the Printers folder, and select Properties.

Page 17

• Locate the Delete Port button. This button is on the Details or Ports tab, depending on

your version or Windows.

• If the WPS-0104 LevelOne Wireless Printer Server's IP Address is changed, and you can

no longer print, delete the port (see procedure above) and re-install it.

Advanced Port Options

The options for the Peer-to-peer Printing are accessed via the Port Settings button.

Use Start - Settings - Printers to open the Printers folder, then right-click the Printer, and select Properties. The Port Settings button is on the Details or Ports tab, depending on your version of Windows.

An example screen is shown below:

Figure 12: Port Settings (Peer-to-peer Driver)

Items shown on this screen are as follows:

Port

If desired, click Browse to select a different WPS-0104 LevelOne Wireless Printer Server. If the selected device has multiple ports, the Select Device Port button can be used to select the port.

The Port Name can not be changed after installation. This name is shown in the Printer's Properties.

Banner

Check this option to print a banner page before each print job.

• If using a PostScript Printer, check the PostScript box.

• The User Name will be printed on the banner page.

Retry Interval

Sets how often Windows will poll the WPS-0104 LevelOne Wireless Printer Server to establish a connection when the printer is busy. Increase this value if you get too many warning messages.

Page 18

Windows SMB Printing

This method requires no additional software to be installed, but the NetBEUI or TCP/IP protocol must be installed on your PC. Use the following procedure to install the WPS-0104 LevelOne Wireless Printer Server's printer as a Windows SMB network printer:

1. Double-click the Network Neighborhood icon on the desktop.

2. On the View menu, select Details.

3. Locate the desired WPS-0104 LevelOne Wireless Printer Server, as shown below:

• If it is the same Workgroup as your PC, it will be listed on screen.

• If it is in a different workgroup, double-click Entire Network, then double-click the

appropriate Workgroup to open it.

Figure 13: Network Neighborhood

4. Double-click the WPS-0104 LevelOne Wireless Printer Server icon to view a Printer icon for each printer port. The "Comment" field may indicate what type of printer is connected to the port.

5. To install a printer, right-click the desired printer icon, and choose "Install", as shown below. This will start the Add Printer wizard.

Figure 14: Install SMB Printer

6. Follow the prompts to complete the installation.

• For information about the question "Do you print from MS-DOS programs?", see

Printing from MS-DOS Programs below.

• Select the Printer Manufacturer and Model to match the printer connected to this port

on the WPS-0104 LevelOne Wireless Printer Server, and complete the Wizard.

Page 19

7. This printer will now appear in your Printers folder (Start - Settings - Printers) and can be used like any other printer. However, SMB printing is not suitable for large complex print jobs - you should use the Peer-to-peer Printing instead.

Page 20

Windows with Server-based Print Queues

With a Server-based Print Queue, the Print Server is installed on an existing Network Server (Windows, Unix, or NetWare), rather than on your PC. If your Network Administrator uses this system, each Windows client must be set up as follows:

1. Open your Printers folder, and start the Add Printer Wizard.

2. When prompted, select Network Printer.

3. When prompted for Network Path or Queue Name:

• On Windows 98SE/ME, click the Browse button

• On Windows 2000/XP, leave the field blank and click Next

Figure 15: Network Path - Windows 98SE/ME

Figure 16: Network Path - Windows XP

4. Browse the network, and locate the Server and Printer (or Print Queue) which your Network Administrator advised you to use.

5. Click OK, then Next.

6. Select the correct printer Manufacturer and Model, as advised by your Network Administrator, and click Next.

7. Follow the prompts to complete the Wizard.

The new printer will be listed with any other installed printers, and may be selected when printing from any Windows application.

Page 21

Macintosh (AppleTalk)

The WPS-0104 LevelOne Wireless Printer Server supports AppleTalk (EtherTalk), PAP, ATP, NBP, ZIP and DDP protocols, enabling Macintosh computers on the network to view and use the WPS-0104 LevelOne Wireless Printer Server as a regular AppleTalk printer.

Normally, no configuration is required.

Software Requirements

System 9.x OS or newer.

AppleTalk Setup

1. Click the apple icon and choose Control Panel - AppleTalk.

2. Ensure that Ethernet is selected under AppleTalk Connection.

3. Click Chooser. The Chooser panel will open.

4. Click on either the LaserWriter 8 icon (recommended) or the LaserWriter 7 icon. LaserWriter 8 makes use of the fonts installed in the printer itself, so the printing response time is quicker. LaserWriter 7 uses the fonts installed in the computer, which increases network traffic and takes more printing time.

5. Choose a PostScript printer from the list.

6. Click Create and it will search PPD automatically.

7. Select a printer description from the list.

8. Click Select. Configuration is now complete.

Printing

Printing with the WPS-0104 LevelOne Wireless Printer Server installed in an AppleTalk network is identical to normal printing. Just select File - Print and choose the desired printer.

Advanced Setup and Management

In a mixed Windows PC/Macintosh environment, you can use BiAdmin to configure the WPS0104 LevelOne Wireless Printer Server. See Chapter 5 for details on installing and using BiAdmin.

Page 22

+ 58 hidden pages