Silex technology SX-300U User Manual

Download

Page 1

WA00970XX

200404

Users Manual SX

Page 2

INDEX

1. Introduction .............................................................................. 1-1

Safety Instructions........................................................................ 1-3

Users Manual SX

2. About This Product ................................................................... 2-1

The Package Contents................................................................. 2-1

About PRICOM SX-300U ............................................................. 2-2

Software Specification............................................................... 2-2

Hardware Specification ............................................................. 2-3

Equipment Explanation ............................................................. 2-4

About User Software SX .............................................................. 2-6

3, How to Install............................................................................ 3-1

Prepare Items............................................................................ 3-1

How to Connect PRICOM to a Printer ...................................... 3-2

Page 3

4. Using PRICOM in Windows Environment ................................ 4-1

Print Using TCP/IP ....................................................................... 4-1

Quick Setup .............................................................................. 4-2

Install JC-Print2002................................................................... 4-6

Adding Printer Port.................................................................... 4-9

Adding JC-Print2002 LPR Port ...........................................................4-10

Adding JC-Print2002 IPP Port.............................................................4-12

Adding JC-Print2002 Raw (9100) Port................................................ 4-14

Users Manual SX

Configuring Printer Driver ....................................................... 4-16

For Windows 95/98/Me User ..............................................................4-16

For Windows NT 4.0/2000/XP/Server 2003 User ............................... 4-18

Print Using Generic Function of Windows.................................. 4-20

Print Using LPR Port of Windows NT 4.0................................ 4-20

Print Using "LPR Port" of Windows 2000, Windows XP

Windows Server 2003 ............................................................. 4-23

Print Using "Standard TCP/IP Port" of Windows 2000,

Windows XP and Windows Server 2003................................. 4-27

Print Using "IPP Port" of Windows 2000, Wiondows XP

Windows Server 2003 ............................................................. 4-33

Print Using NetBEUI, NetBIOS over TCP/IP .............................. 4-36

Verify the PC Network Configuration (NetBEUI) ..................... 4-36

For Windows 95/98/Me User ..............................................................4-36

For Windows 2000 User .....................................................................4-39

NetBIOS over TCP/IP .........................................................................4-39

For Windows XP/Server 2003 User .................................................... 4-40

Print Using NetBEUI, NetBIOS over TCP/IP........................... 4-42

About NetBEUI, NetBIOS over TCP/IP ...................................... 4-43

File Structure of PRICOM in NetBEUI, NetBIOS over TCP/IP

environment ............................................................................ 4-43

Page 4

5. Using PRICOM in UNIX/Linux Environment ............................ 5-1

Configuring IP Address................................................................. 5-2

Configuring IP Address by BOOTP ........................................... 5-2

Configuring IP Address by RARP ............................................. 5-3

Configuring IP Address by ARP ................................................ 5-4

Configuring Host File.................................................................... 5-5

Printing by LPD ............................................................................ 5-6

Using PRICOM in Solaris Environment .................................... 5-7

Solaris 2.6/7/8 ....................................................................................... 5-7

Solaris 2.3x-2.5x ...................................................................................5-9

Running PRICOM in HP-UX 9.x/10.x Environment ................. 5-11

Using setnetlp Tool ..............................................................................5-13

Using PRICOM in AIX 4.x.x Environment ............................... 5-18

Using PRICOM in BSD UNIX Environment ............................ 5-20

Using PRICOM in Linux Environment ..................................... 5-22

Using Print Queue Creation Tool of Red Hat Linux ............................. 5-24

Using the Print Queue Creation Tool of Turbo Linux........................... 5-25

Users Manual SX

Printing Using FTP ..................................................................... 5-26

Printing .................................................................................... 5-27

Checking the status................................................................. 5-29

Page 5

6. Using PRICOM in NetWare...................................................... 6-1

Printing in NetWare Environment ................................................. 6-2

Verifying NetWare Environment ................................................ 6-2

Using Bindery Mode.................................................................. 6-3

Configuration Using Quick Setup ..........................................................6-3

Configuring Printer Port ........................................................................ 6-9

Users Manual SX

Using NDS Mode .....................................................................6-11

Configure Using Quick Setup.............................................................. 6-11

Configuring Printer Port ...................................................................... 6-17

Printing Mode ............................................................................. 6-19

Print Server Mode ................................................................... 6-19

Remote Printer Mode .............................................................. 6-20

7. Macintosh Environment............................................................ 7-1

Setup and Printing........................................................................ 7-2

Mac OS 8/9 ............................................................................... 7-2

Setup AppleTalk Service .......................................................................7-2

Printing .................................................................................................. 7-3

Mac OS X.................................................................................. 7-4

Enable the Apple Talk Service............................................................... 7-4

Printing .................................................................................................. 7-5

Setup the TCP/IP (MacTCP) Protocol.......................................... 7-6

Configure the TCP/IP(Mac TCP) Protocol ................................ 7-6

Installing and Using AdminManager.......................................... 7-7

Printing Using Rendezvous..................................................... 7-10

Page 6

8. Functions for Configuration ...................................................... 8-1

Configuration by Using AdminManager........................................ 8-1

Starting AdminManager ............................................................. 8-2

Searching PRICOM Using AdminManager ............................... 8-4

Functions of AdminManager ..................................................... 8-5

AdminManager Menu Structure ............................................................8-5

Printer Status ........................................................................................ 8-6

System Status ....................................................................................... 8-6

Configuration Parameters List .............................................................. 8-7

Users Manual SX

Configuring PRICOM Using AdminManager ................................ 8-8

Configuring Print Server............................................................ 8-8

Configurating NetWare.............................................................. 8-9

Creating NetWare Queue......................................................................8-9

Using PRICOM with Bindery Connection ............................................. 8-9

Using PRICOM via bindery mode: Configuring print port ................... 8-13

Using PRICOM via NDS mode. .......................................................... 8-15

Using PRICOM via NDS connection: Configuring print port ............... 8-19

Configuring PRICOM via Web Browser ..................................... 8-21

Display PRICOM Webpage..................................................... 8-22

Displaying the webpage from AdminManager.....................................8-22

Displaying the webpage from Web browser........................................8-22

Configuration via the Webpage ............................................... 8-23

Configuring PRICOM using TELNET ......................................... 8-24

Page 7

9. PRICOM Monitor SX ................................................................ 9-1

About PRICOM Monitor SX.......................................................... 9-1

Starting PRICOM Monitor SX.................................................... 9-1

Display PRICOM Monitor SX (Character Mode) ....................... 9-2

Menu ..................................................................................................... 9-3

Users Manual SX

Display PRICOM Monitor SX (Full Mode) ................................. 9-4

Printer Status Information ..................................................................... 9-4

System Information ............................................................................... 9-5

Menu ..................................................................................................... 9-5

Options Setting ......................................................................... 9-6

Status Monitor ....................................................................................... 9-6

Display tab ............................................................................................9-7

Character ..............................................................................................9-8

10. FAQ ...................................................................................... 10-1

Question during Initial Installation ........................................... 10-1

Main menu does not start even after inserting the CD-ROM ..............10-1

PRICOM is not found even after searching in the configuration utility

(Quick Setup, AdminManager) or PRICOM is not recognized on

the network ......................................................................................... 10-2

Unable to print self-diagnostic report ..................................................10-3

Self-diagnostic report is NG ................................................................ 10-3

Communication error occurs while configuring IP address .................10-4

Question while Printing ........................................................... 10-5

Print job is not printed .........................................................................10-5

Question Regarding TCP/IP.................................................... 10-6

Print job in not printed ........................................................................ 10-6

Error during printing ............................................................................10-7

Dial-up connection box appears when printing job is executed. ......... 10-7

Page 8

Question regarding Windows NetBEUI/NetBIOS over TCP/IP 10-8

Error message appears when printing with NetBEUI ..........................10-8

Questions regarding UNIX/Linux ............................................ 10-8

When test printing with "Red Hat Linux queue creating tool",

characters are mutilated. .................................................................... 10-8

Users Manual SX

Question regarding NetWare .................................................. 10-9

PRICOM can not establish the connection with NetWare ...................10-9

PRICOM can not establish the connection with NetWare server

(RPRINTER mode) .............................................................................10-9

PRICOM can not establish the connection with NetWare server.

(PSERVER mode).............................................................................10-10

Question regarding Macintosh ...............................................10-11

PRICOM is not recognized by chooser ............................................. 10-11

The error message "Short of menory" appears while printing; or only

Chinese characters are printed; or blank paper is ejected................ 10-11

Is there any operational differene on PRICOM depending on the

Mac OS version? ..............................................................................10-12

Other ..................................................................................... 10-13

Configuration can not be changed by PRICOM web page. ..............10-13

What are the default user name and password? ..............................10-13

Appendix ..........................................................................................1

Enhanced Function ..........................................................................1

Network Plug & Play .....................................................................1

IP Filtering Function ......................................................................2

E-Mail Alert Function(SMTP) ........................................................4

Direct E-mail printing (POP)..........................................................5

Configuration Settings ......................................................................6

Page 9

User Registration .............................................................................1

Users Manual SX

Page 10

Users Manual SX

1. Introduction

Thank you for purchasing our product. This manual provides information on how to configure

and use PRICOM SX-300U (PRICOM). To correctly and safely use PRICOM please read

carefully.

PRICOM is a mini print server that connects to a printer using a USB cable. PRICOM can be

used anywhere from a small-scale network environment to a large-scale network environment

where two or more network protocols are intermingled. In addition the printer status (paper

out, printer offline, etc.) can be monitored from a PC by using the PRICOM Monitor SX

bundled with PRICOM.

1-1Introduction

Page 11

Users Manual SX

[About this Manual]

- Copying all or part of this manual without our permission is forbidden.

- The contents of this manual may be changed without advance notice.

- If you have any question regarding this manual or our products, please contact our customer

support.

- Please note that the actual screens will vary from the examples in this manual. This is

caused by different versions of operating systems on the PC, upgrades, etc.

- This manual has been edited very carefully. However, silex technology, Inc. is not responsible

for any mistakes included in this manual or any damages, direct or indirect, arising from the

use of this manual.

- PRICOM is a registered trademark of silex technology inc.

- Microsoft, Windows, Windows NT etc. are registered trademarks of Microsoft Corporation

in the U.S. and other countries.

- Other brand or product names are registered trademarks or trademarks of their respective

companies.

[About the notation]

This manual uses the following symbols to point out specific information. The information

after the symbols should always be followed.

This symbol indicates important information that needs to be observed

TIP

when operating the product. Make sure to read this information for safe

and proper use.

NOTE

This symbol indicates information that is useful when using the product.

If you experience difficulties operating the product, please refer to this

information first.

1-2Introduction

Page 12

Users Manual SX

Safety Instructions

- To ensure safe and proper use, please read the following information carefully before using

PRICOM. The safety instructions include important information on safe handling of the product

and on general safety issues.

- This manual contains safety instructions that must be observed to avoid potential hazards

that could result in personal injuries or material damage. The safety instructions have been

classified according to the potential risk involved as follows:

“Danger” indicates the existence of a hazard that could result in bodily

Danger

injury if the safety instruction is not observed.

Examples

Warning

“Warning” indicates the existence of a hazard that could result in material

damage if the safety instruction is not observed.

This symbol warns of possible danger.

The danger symbol will contain another symbol or have a picture near

it. (This warns of possible electrical shock)

This is the prohibit symbol.

This symbol will include another symbol or have a picture near it

to indicate what is prohibited.

This is the prohibit symbol.

This symbol indicates what is prohibited specifically.

This indicates a regulation by its contents.

The regulation will appear inside or near this symbol. (Indicates to

unplug).

1-3Introduction

Page 13

Users Manual SX

Danger

Warning about physical connections

Do not allow physical impact: When damaged, unplug PRICOM from

power and contact your dealer. Failure to take this action could cause

fire or an electrical shock.

Keep the cord and cables away from children. They may be injured

or receive a shock

If PRICOM is detached from the device(s), unplug the power to the

device(s) before reconnecting.

If the printer has a ground wire, it must be used to prevent electrical

shock and power surges.

1-4Introduction

Page 14

Users Manual SX

Danger

The following warnings should be observed during use.

Do not disassemble or modify the cover of PRICOM.

Do not use PRICOM with the case removed. You may receive an

electric shock.

Do not attempt to check, adjust or repair PRICOM by yourself. You

may receive an electric shock.

Check with your dealer if the product needs to be repaired.

If PRICOM becomes hot, or you smell smoke, turn off the printer

then unplug the power cable and disconnect this device immediately.

If a foreign object (liquid, metal) gets into PRICOM, turn off the printer

then unplug the power cable and disconnect this device immediately.

Contact your dealer about repairing PRICOM.

1-5Introduction

Page 15

Users Manual SX

Warning

Warning about physical connections

When unplugging PRICOM, do not pull on the cord. The cord may

break resulting fire and/or electric shock. Pull on the plug only.

Do not put PRICOM on an unstable location. The product may fall

causing injury or damaging the product.

Do not put PRICOM in a humid or dusty place. Fire or electric shock

may occur.

When moving PRICOM, disconnect the power and printer cables.

Fire or electric shock may occur.

1-6Introduction

Page 16

Users Manual SX

Warning

The following warnings should be observed during use.

When the product will not be used for an extended time, disconnect and

unplug the power cable.

Verify all cables are connected properly before using PRICOM.

1-7Introduction

Page 17

Users Manual SX

2. About This Product

This chapter explains about the PRICOM SX-300U product.

The Package Contents

The package contains the following, please check items before continuing.

1, Product(PRICOM SX-300U)

2, AC adapter

3, CD(User Software SX)

4, Quick Setup Guide

5, Warrnty booklet

2-1About This Product

Page 18

Users Manual SX

About PRICOM SX-300U

Software Specification

Supported Protocols

TCP/IP

Raw(9100) Port, LPD, FTP, IPP, HTTP, TELNET, DHCP, BOOTP, SNMP, POP3,

SMTP, DNS, DDNS, WINS, TCP, UDP, ARP, RARP, IP, ICMP, NetBIOS over TCP/IP

NetBEUI

SMB, NetBIOS, WINS

NetWare

IPX, SPX, SNMP, NDS(NetWare 4.x/5/6)

Remote printer mode (up to 8 servers)

Print server mode (up to 8 servers, 32 queue)

Frame automatic detection from IEEE 802.2, IEEE 802.3, Ethernet-II or

SNAP frame type

AppleTalk

PAP, ATP, ZIP, RTMP, NBP, AEP, DDP, AARP, ELAP, AppleTalk phase2

Operating Environment

PRICOM will support the following Operating System.

Windows (95, 98, Me, NT 4.0, 2000, XP, Server 2003)

UNIX, Linux

NetWare (3.x, 4.x, 5.x, 6.x)

Macintosh (MacOS 8.6 or newer, MacOSX 10.2 or newer)

NOTE

- When you use PRICOM in a Macintosh environment, you need the printer driver for AppleTalk

which is supplied with the printer.

2-2About This Product

Page 19

Users Manual SX

Hardware Specification

Network Interface

-10BASE-T/100BASE-TX (auto-detection): 1 port

Printer Interface

- USB 1.1(A-Type)

Others

- Push switch : 1 push switch

- LED : 3 LEDs: Status (Orange), 10Base LINK (Green),

100Base LINK (Green).

2-3About This Product

Page 20

Users Manual SX

Equipment Explanation

This section explains the names of parts and their functions.

Top

Side

Ethernet Address

(The last 6 digits are

PRICOM serial number)

Power connector

10 Mbps LED

(Green)

100Mbps LED

(Green)

Bottom

USB Port

Push Switch

<Side>

Status LED (Orange)

Flashes during data transfer.

10Mbps LED (Green)

LED lights while connecting to 10Mbps.

100Mbps LED (Green)

LED higths while connecting to 100Mbps.

USB Port

Connects a USB Cable (A Type connector)

Power Connector

Connects AC adapter

Push Switch

By pushing the push switch, the server can be restored to factory-default settings or

do a self-diagnosisand print the configuration settings.

Status LED

(Orange)

2-4About This Product

Page 21

Users Manual SX

Ethernet Address

The Ethernet (MAC) Address of the device is found on the bottom. The last 6 digits are PRICOM’s

serial number.

- If the Ethernet Address is 00:80:92:18:0E:1A (noted as 008092180E1A) then PRICOM’s serial

number is 180E1A.

NOTE

1. Please verify that AC adapter is not connected to PRICOM.

2. While pushing the push switch, connect the AC adapter to the power supply connector of PRICOM.

Shortly after a power is supplied, all of the Light Emitting Diodes will light and then some will turn off.

3. Continuing pushing (about 5 seconds) — when the restoration starts all of the Light Emitting Diodes

will light. When the status LED lights, release the push switch.

Push Switch

- Do not turn off the power to PRICOM while it is initializing to factory default.

TIP

1. Verify that AC adapter is not connected to PRICOM.

2. Verify that the printer is connected and ready to print.

3. Verify that the printer is powered on.

4. While holding the push switch, plug in the power supply. Status LED (Orange), Link LED (Green), InfraLED

(Green) will light.

5. Hold the push switch (for about 30 seconds). The self test and configuration will then begin.

- When PRICOM is turned on again after factory default is completed, do not push the pushbutton

switch.

- Do not turn off the printer until the printing of self-test/configuration settings has finished.

- The printer must have an internal font for the self-test/configuration settings to print.

TIP

2-5About This Product

Page 22

Users Manual SX

About User Software SX

This section explains about the User Software SX. The cofiguration utility and Users Manual

are contained on the bundled CD and can be used in Windows and Macintosh environments.

- User Software SX can not be used in UNIX/Linux and NetWare.

- Use User Software SX in a browser environment with Internet Explorer 4.0 (SP2) or above.

NOTE

The below screen will be executed automatically when installing User Software SX to your

Windows PC.

-If the below screen does not open automatically, open My Computer. select the CD ROM drive

and execute "autorun.exe".

NOTE

- ReadMe

Click on ReadMe for important information about User Software SX. Make sure to read this

information carefully before starting to use PRICOM.

- Setup

Take out. This leads you to the PRICOM configuration utility (Quick Setup, Advanced Setup)

and the printing software (JC-Print2002).

- Manual

The manual is a PDF file which can be viewed with Adobe Acrobat Reader.

2-6About This Product

Page 23

Users Manual SX

The below screen will appear after clicking Setup from the top menu.

-Once the initial installation of PRICOM is complete, you can start using PRICOM by just installing

NOTE

JC-Print2002 on your PC.

- Quick Setup (recommended for initial installation)

Initial configuration of PRICOM can easily proceed by interacting with the wizard.

Printing software JC-Print2002 can also be easily installed in a similar way.

This is recommended for initial installation.

- Advanced Setup

Start or install the management utility "AdminManager", Admin Manager allows detailed PRICOM configuration

and manages the printer.

- JC-Print2002

Install PRICOM Monitor SX and printing software that enables you to print directly from Windows environment.

LPR (specific to silex products), IPP or Raw mode can be selected.

- Option (Only for PRICOM supporting the enhanced features)

This button will lead you to install the configuration utility that enables the PRICOM optional functions. The

utility can only be used with PRICOM supporting the enhanced features.

NOTE

- You may not be able to use the optional functions depending on the PRICOM you use. Make

sure PRICOM supports the enhanced features.

2-7About This Product

Page 24

Users Manual SX

3, How to Install

This chapter explains how to install PRICOM for printing.

- If PRICOM has been used in another network, return it to factory default prior to setup.

TIP

Prepare Items

The following items are required in order to connect PRICOM to a network.

Ethernet Hub

Network Cable

USB Cable

A - B Type

3-1How to Install

Page 25

Users Manual SX

How to Connect PRICOM to a Printer

- The following explanation is based on using a printer.

TIP

1. Connect the AC adapter to PRICOM.

2. Insert the power cable of printer into

an electrical outlet.

3. Connect a network cable from an

Ethernet HUB to PRICOM.

- Be sure that PRICOM is powered on prior to powering up the connected USB device.

Power Cable

AC Adapter Cable

4. Use a USB cable to connect

PRICOM(type A connector)to a printer

(type B connector)

- The shape of the connectors on a USB cable have 2 different types.

NOTE

A Type

- Refer to the following chapter about how to install on each OS.

B Type

OS Chapter

Windosws 4

UNIX/Linux 5

PRICOM SX-300U

Ethernet HUB

Netware 6

Macintish 7

3-2How to Install

Page 26

Users Manual SX

4. Using PRICOM in Windows Environment

This chapter explains how to print using TCP/IP, NetBEUI and NetBIOS over TCP/IP protocol

of Windows environment.

Print Using TCP/IP

Following indicates how to print using TCP/IP protocol.

- Refer to chapter "2 How to Install" about how to connect PRICOM to printer.

NOTE

- Make sure to install printer driver before you start using PRICOM.

- If you are a WindowsNT/2000/XP user, you can use standard printing function included Windos

OS. If you want to use it, refer to "Print Using Embedded Printing Client Function" in this chapter.

In case of initial installation

and printing

Configure IP address using QuickSetup

Start

In case of printing

Install JC-Print2002

Configure printer port

4-1Using PRICOM in Windows Environment

Page 27

Users Manual SX

Quick Setup

1. Insert the User Software SX in the CD-ROM drive of your Windows PC. The main menu

screen will be displayed.

Click Setup.

2. The below screen will be displayed.

3. Quick Setup loads.

Click Quick Setup.

Click Next.

4-2Using PRICOM in Windows Environment

Page 28

Users Manual SX

4. Confirm the Software License Agreement.

5. Select PRICOM to be configured.

Read the agrement and click Yes

if you accept it.

Select PRICOM to be configured.

Click Next.

-If the PRICOM does not appear in the list, click Search. You can search for a PRICOM by typing in its Ethernet address directly.

NOTE

6. Assign an IP address

-If NetWare Client is installed and PRICOM is supporting NetWare (Enable), NetWare

NOTE

When you have DHCP server in your environment.

(A) Obtain an IP address from DHCP server automatically.

configuration screen will appear.

Click Get IP Address Automatically.

ŽŸ‚Ö

Click Next.

4-3Using PRICOM in Windows Environment

Page 29

Users Manual SX

(B) Assign an IP address manually.

Assign an optional IP address.

Click Next.

When you do not have DHCP server in your environment.

Assign the optional IP address.

7. Verify the configuration parameters.

Click Next.

Click Execute.

4-4Using PRICOM in Windows Environment

Page 30

11. Setup is complete.

-Proceed to install JC-Print2002.

JC-Print2002 is a printing software that enables printing directly from Windows.

NOTE

Users Manual SX

Click Yes.

Click Finish.

4-5Using PRICOM in Windows Environment

Page 31

Users Manual SX

Install JC-Print2002

To print directly from Windows environment using TCP/IP protocol, use the JC-Print2002

bundled with PRICOM.

JC-Print2002 is a printing software that enables users to use LPR (dedicated to silex products),

IPP and Raw (9100) port. JC-Print2002 also includes PRICOM Monitor SX.

When installation is complete, the wizard to add a printer port will be stared.

-LPR (Line Printer Remote)

NOTE

A widely used protocol that enables users to execute printing to printers on the local area

network (LAN).

-IPP (Internet Printing Protocol)

This protocol enables users to execute printing to network printers via Internet.

-Raw (9100) port

This function enables users to execute printing to printers on the local area network (LAN).

Information can be printed at a high speed without spool.

-PRICOM Monitor SX

You can check the printer status with this monitor. For more details, refer to " 9. PRICOM

Monitor SX".

1. Verifying installing method.

(A) Install JC-Print2002 following Quick Setup.

(B) Install JC-Print2002 .

Click Yes.

Click Finish.

Insert the CD into the CD-ROM drive.

Click Setup, then JC-Print2002.

4-6Using PRICOM in Windows Environment

Page 32

Users Manual SX

2. JC-Print2002 installation wizard will start.

3. Confirm the Software License Agreement.

Click Next.

4. Verify the Destination Directory.

-Click Reference to specify the destination directory.

NOTE

Read the agrement and click Yes

if you accept it.

Click Next.

4-7Using PRICOM in Windows Environment

Page 33

Users Manual SX

5. Specify the group name to be registered at the start menu.

Click Next.

6. Begin the installation.

7. Installation is complete.

Click Start.

Select Yes..

Click Finish.

4-8Using PRICOM in Windows Environment

Page 34

Users Manual SX

Adding Printer Port

JC-Print2002 has three available options for printing; Print using LPR, Print using IPP and

Print using Raw Mode.

Select the protocol to be used for printing, then click Next to start using the specified printing

option.

(A)

1. Adding printer port following the JC-Print2002 installation.

Select Yes.

Click Next.

2. JC-Print2002 port adding wizard starts,

Click Next.

Click Start, then Programs, then JC-Print2002, then JC-Print2002 Port adding.

(B)

Click Next.

4-9Using PRICOM in Windows Environment

Page 35

Users Manual SX

Adding JC-Print2002 LPR Port

1. Select LPR (Line Printer Remote).

Select Print with LPR (Line Printer

Remote).

Click Next.

2.Display the list of print servers on the network by clicking Searching Print Server.

Select the PRICOM you want to print to.

3. Type in printer port name.

Click Next.

If you do not want to have a specific

name, use the default printer port name.

Click Next.

4-10Using PRICOM in Windows Environment

Page 36

Users Manual SX

4. Verify the configuration.

Click Finish.

5. Select the printer you want to use with PRICOM.

6. Port configuration is complete.

Click Next.

ŽŸ‚Ö

Click Finish.

4-11Using PRICOM in Windows Environment

Page 37

Users Manual SX

Adding JC-Print2002 IPP Port

1. Select IPP (Internet Printing Protocol).

Select Print with IPP (Internet Printing

Protocol).

Click Next.

2. Select either Use Internet Explorer configuration, Deactivate proxy server for

Internet connection or Configure proxy server manually.

Click Next.

3. Type in URL assigned to PRICOM for Printer URL. PRICOM IPP printer URL is "/ipp"

or "/ipp/lp".

Click Next.

Ex.): When URL is “abc.co.com”, Type

in http://abc.co.com/ipp/lp

Ex.) When IP address is

“192.168.20.185”, Type in

http://192.168.20.185/ipp/lp

NOTE

-If you click Next, you can make sure if specified URL exists..

4-12Using PRICOM in Windows Environment

Page 38

Users Manual SX

4. Configure the port name for printing.

5. Verify the configuration.

If you do not want to have a specific

name, use the default printer port name.

Click Next.

ŽŸ‚Ö

Click Finish.

6. Select the printer you want to use with PRICOM.

Click Next.

7. Configuration is complete.

Click Finish.

4-13Using PRICOM in Windows Environment

Page 39

Users Manual SX

Adding JC-Print2002 Raw (9100) Port

1. Select Raw mode.

Select Print with Raw mode (TCP/IP

9100).

Click Next.

2. Display the list of print servers on the network by clicking Search for Print Server

Select the PRICOM you want to print to.

-To verify that the specified print server can be access via the 9100 port, click Next.

NOTE

3. Type in print port name.

Click Next.

The default printer port name

(RAW_IP address) can be used.

Click Next.

4-14Using PRICOM in Windows Environment

Page 40

Users Manual SX

4. Verify the configuration.

Click Finish.

5. Select the printer you want to use with PRICOM.

6. Configuration is complete.

Click Next.

Click Finish.

4-15Using PRICOM in Windows Environment

Page 41

Users Manual SX

Configuring Printer Driver

This section explains how to configure printer driver.

-If you do not configure printer driver, the following error dialog may appear.

NOTE

For Windows 95/98/Me User

1. Click Start, then Settings, then Printer, then open the printer property.

In this case, click No and configure printer driver by following steps.

2. Select Details.

Select Properties.

Select Sool Settings.

4-16Using PRICOM in Windows Environment

Page 42

Users Manual SX

3. Select Disable bidirectional support for this printer.

Select Disable bidirectional support

for this printer.

Click OK.

4. Configuration is complete.

Click Apply.

4-17Using PRICOM in Windows Environment

Page 43

Users Manual SX

For Windows NT 4.0/2000/XP/Server 2003 User

1. Click Start, then Settings, then Printer, then open the printer property.

Select Properties.

2. Select Ports.

Select Ports.

4-18Using PRICOM in Windows Environment

Page 44

Users Manual SX

3. Configure bidirectional.

Check off Enable bidirectional support.

-If you use Canon Laser Shot Utility [Print Buddy II] and [NetSpot JobMonitor], check in Enable

TIP

4. Configuration is complete.

bi- directional support.

Click Apply.

4-19Using PRICOM in Windows Environment

Page 45

Users Manual SX

Print Using Generic Function of Windows

This section explains how to print using Windows embedded printing client function.

Print Using LPR Port of Windows NT 4.0

-In order to print using LPR port, LPR port must be added. Click Start, then Settings, then

TIP

1. Click Start, then Settings, then Printers, then double-click Add Printer.

Control Panel, then Network, then select Services, then click Add, then select Microsoft

TCP/IP Printing, then OK. Component is installed. Restart the computer.

Select My Computer.

2. Add Printer

3. Select the printer port.

Click Next.

Click Add Port.

Select LPR Port and click New Port.

4-20Using PRICOM in Windows Environment

Page 46

Users Manual SX

4. Add LPR compatible printer.

5. Verify the Printer Port.

Type in the IP address configured on the

PRICOM. Type in lp.

Click OK.

Verify the appropriate port is checked.

Click Next.

6. Select the printer driver.

7.Verify the printer driver.

Select the printer driver to be used.

Click Next.

Select Keep existing driver

(recommended) or Replace existing

driver.

Click Next.

NOTE

-When installing an updated driver, select Replace existing driver.

4-21Using PRICOM in Windows Environment

Page 47

Users Manual SX

8. Register the Printer name.

9. Select if the printer to be shared or not .

If you do not wish to specify the printer

name, use the printer name already set.

Select whether the printer is the default

printer or not.

Click Next.

Select Shared or Not shared.

Click Next.

10. Select if you want test print.

Select Yes.

Click Finish.

11. If the test page is printed properly, configuration is complete.

4-22Using PRICOM in Windows Environment

Page 48

Users Manual SX

Print Using "LPR Port" of Windows 2000, Windows XP Windows

Server 2003

-In order to print using LPR port, LPR port must be added. Click Start, then Control Panel, then

NOTE

1. Click start, then Control Panel, then Printers and Other Hardware, then Add a

printer.

Add or Remove Prpgrams (For Windows 2000, click start, then Settings, then Control

Panel, then Add or Remove Programs), then Add/Remove Windows Components. Windows

Components Wizard will be displayed, then click Components, then Other Network File and

Printing Services, then Details, then Print Services for Unix, then OK. Windows Components

Wizard will be displayed. Click Finish.

-Screens displayed below are for Windows XP. If you use Windows 2000, the screens may

vary.

-If you use Windows 2000, click Start, then Settings, then Printers, then double-click Add

Printer.

NOTE

2. Select the printer to be configured.

Click Next.

Select Local printer attached to this

computer and remove the check from

Automatically detect and ...

Click Next.

NOTE

-If you use Windows 2000, select Local printer and remove the check from Automatically

detect and ...

4-23Using PRICOM in Windows Environment

Page 49

Users Manual SX

3. Select the printer port.

4. Add LPR compatible printer.

Check Create a new port and select

Standard TCP/IP Port.

Click Next.

Type in the IP address configured on the

5. Select the printer driver.

PRICOM. Type in lp.

Click OK.

Select the printer driver to be used.

Click Next.

4-24Using PRICOM in Windows Environment

Page 50

Users Manual SX

6. Verify the printer driver.

7. Register the printer name.

Select Keep existing driver

(recommended) or Replace existing

driver.

Click Next.

You do not need specify to the printer

name, the default printer name can be

8. Select if the printer will be shared or not .

used.

Select if the printer will be the default

printer or not.

Click Next.

NOTE

-If the printer is shared with other computers in the same network, select Shared as.

4-25Using PRICOM in Windows Environment

Page 51

Users Manual SX

9. Select if you want a test print.

10. Verify the configuration.

Click Next.

Click Finish.

11. If the test page is printed properly, configuration is complete.

4-26Using PRICOM in Windows Environment

Page 52

Users Manual SX

Print Using "Standard TCP/IP Port" of Windows 2000, Windows XP

and Windows Server 2003

Screens displayed below are for Windows XP. If you use Windows 2000, the screen may

vary.

1. Click start, then Settings, then Control Panel, then Printers and Other Hadware,

then Add a printer..

Click Next.

-If you use Windows 2000, click Start, then Settings, then Control Panel, then Printers, then

Add Printer.

NOTE

2. Select the printer to be configured.

-If you use Windows 2000, select Local Printer and remove the check from Automatically

detect and...

NOTE

Select Local printer attached to this

computer and remove the check from

Automatically detect and install....

Click Next.

4-27Using PRICOM in Windows Environment

Page 53

Users Manual SX

3. Select the printer port.

Check Create a new port and select

Standard TCP/IP Port.

Click Next.

4. Add Standard TCP/IP Printer Port Wizard will be started.

5. Add TCP/IP Printer Port .

Click Next.

Type in the IP address configured

to PRICOM.

If you do not wish to specify the Port

Name, use the default (IP_xxx.xxx.xxx).

Click Next.

4-28Using PRICOM in Windows Environment

Page 54

Users Manual SX

6. Identify the device type.

7. Type in the port information.

Check Custom and click Settings.

Click Next.

(A) Raw Mode

-Click OK, the screen 6 will be displayed, then click Next.

NOTE

Select Raw.

Type in 9100.

Click Next.

4-29Using PRICOM in Windows Environment

Page 55

(B) LPR Mode

-Click OK, screen 6. will be displayed, then click Next.

NOTE

Users Manual SX

Select LPR.

Type in lp and check LPR Byte Counting

Enabled.

Click OK.

8. Verify the configuration.

9. Select the printer driver.

Click Finish.

Select the printer driver to be used.

Click Next.

4-30Using PRICOM in Windows Environment

Page 56

Users Manual SX

10. Verify the printer driver.

-When installing the latest driver, select Replace existing driver.

NOTE

Select Keep existing printer driver

(recommended) or Replace existing

driver.

Click Next.

11. Register the Printer name.

12. Select the printer will be shared or not.

If you do not wish to specify the printer

name, use the default printer name.

Select if the printer will be used as the

default printer or not.

Click Next.

Select Do not share this printer or

Shared as.

Click Next.

4-31Using PRICOM in Windows Environment

Page 57

Users Manual SX

13. Select if you want test print.

14. Verify the configuration.

Select Yes.

Click Next.

Click Finish .

15. If the test page is printed properly, configuration is complete.

4-32Using PRICOM in Windows Environment

Page 58

Users Manual SX

Print Using "IPP Port" of Windows 2000, Wiondows XP Windows

Server 2003

-Screens displayed below are for Windows XP. If you use Windows 2000, the screens may

TIP

1. Click start, then Control Panel, then Printers and Other Hardware, then Add a

printer.

vary.

Click Next.

-If you use Windows 2000, click Start, then Settings, then Printers, then double-click Add

Printer.

NOTE

2. Select the printer to be configured.

-If you use Windows 2000, select Network Printer.

NOTE

Select A network printer or a printer

attached to another computer.

Click Next.

4-33Using PRICOM in Windows Environment

Page 59

Users Manual SX

3. Type in PRICOM IP address.

Select Connect to a printer on the

Internet or on the home/office network.

Specify URL or PRICOM IP address.

Click Next.

Select Connect to a printer on the

Ex.): When URL is “silex.localcom”,

NOTE

4. Select the printer driver.

http://silex.localcom/ipp/lp or http://silex.localcom/ipp

Ex.): When IP address is “192.168.20.185”,

http://192.168.20.185/ipp/lp or http://192.168.20.185/ipp

Internet or intranet. Specify URL or

IP address of PRICOM.

Click Next.

Select the printer driver to be used.

Click Next.

4-34Using PRICOM in Windows Environment

Page 60

Users Manual SX

5. Configure the default printer.

6. Configuration is complete.

Select if you want to use this printer as a

default printer.

Click Next.

Click Finish.

4-35Using PRICOM in Windows Environment

Page 61

Users Manual SX

Print Using NetBEUI, NetBIOS over TCP/IP

Follow the steps shown below to print from a Windows environment using NetBEUI, NetBIOS

over TCP/IP protocol.

- Install the printer driver before you start.

NOTE

Verify the PC network configuration

Build NetBEUI, NetBIOS over TCP/IP printing environment

Verify the PC Network Configuration (NetBEUI)

For Windows 95/98/Me User

Make sure that NetBEUI and Microsoft network shared service are added to Network of

Windows 95/98/Me.

1. Click Start, then Settings, then Control Panel.

2. Double-click Network icon.

3. Verify that NetBEUI and File and printer sharing for Microsoft Network are added

to the network component list.

NOTE

-If NetBEUI protocol is not in the current network component list, click Add, then Protocol, then

Microsoft , then NetBEUI to add NetBEUI. If File and printer sharing for Microsoft Network

is not in the current network component list, click Services, then File and printer for Microsoft

Network to add File and printer sharing for Microsoft Network.

4-36Using PRICOM in Windows Environment

Page 62

Users Manual SX

Make sure that TCP/IP and Microsoft network client are added to Network of Windows

95/98/Me and verify if NetBIOS over TCP/IP is usable at TCP/IP properties.

1. Click Start, then Settings, then Control Panel.

2. Double-click Network.

3. Verify that TCP/IP and Microsoft network client are added to Network.

-If TCP/IP is not in The following network components are installed, click Add, then Protocols,

NOTE

then Microsoft, then TCP/IP.

-If Microsoft network client is not in The following network components are installed, click

Services, then Microsoft network client.

4. Open TCP/IP properties, then select NetBEUI, then verify that Enable NetBIOS on

TCP/IP is checked.

-By default, Enable NetBIOS on TCP/IP is checked.

NOTE

4-37Using PRICOM in Windows Environment

Page 63

Users Manual SX

For Windows NT 4.0 User

Make sure that Workstation, NetBIOS interface and NetBEUI protocol are added to

Network of Windows NT 4.0.

1. Click Start, then Settings, then Control Panel.

2. Double-click Network.

3. Verify that Workstation and NetBIOS interface are added to the Services.

-If Workstation is not in the Network Service list, click Add, then select Workstation to add

NOTE

Workstation.

4. Verify NetBEUI is added to Protocol.

-If NetBEUI is not in the list, click Add, then select NetBEUI from Network protocol.

NOTE

Make sure that Workstation, TCP/IP and NetBIOS interface are added to Network of

Windows NT 4.0.

1. Click Start, then Settings, then Control Panel.

2. Double-click Network icon.

3. Verify that Workstation and NetBIOS interface are added to the Services.

-If Workstation is not in the Network Service list, click Add, then select Workstation to add

NOTE

Workstation.

4. Verify TCP/IP is added to Protocol.

-If TCP/IP is not in the list, click Add, then select TCP/IP from Network protocol.

NOTE

4-38Using PRICOM in Windows Environment

Page 64

Users Manual SX

For Windows 2000 User

Make sure that NetBEUI protocol and Microsoft network shared service are added to the

Network of the Windows 2000.

1. Click Start, then Settings, then Control Panel, then Network and Internet Connection.

2. Open Properties of Local area connection.

3. Verify NetBEUI protocol is added.

-If NetBEUI is not in the component list, click Install, then Protocol, then NetBEUI protocol.

NOTE

-If Microsoft Network Client is not in component list, click Install, then Client, then Microsoft

Network Client.

4. Verify that Microsoft Network Client is added.

NetBIOS over TCP/IP

Make sure that Internet Protocol (TCP/IP) and Microsoft Network Sharing Service are

added to Network of Windows NT 4.0 and verify that NetBIOS is configured to Internet

Protocol (TCP/IP).

1. Click Start, then Settings, then Control Panel, then Network and Dial-up Connection.

2. Right-click Local Area Connection, then click properties.

3. Verify Microsoft Network Sharing Services is added.

-If Microsoft Network Sharing Services is not in the list, click Install, then Client, then Microsoft

NOTE

Network Sharing Services.

4. Verify Internet Protocol (TCP/IP) is added.

-If Internet Protocol (TCP/IP) is not in Components checked are used by this connection,

click Install, then Internet Protocol (TCP/IP) to add Internet Protocol (TCP/IP).

NOTE

4-39Using PRICOM in Windows Environment

Page 65

Users Manual SX

For Windows XP/Server 2003 User

Make sure that NetBIOS is configured in Internet protocol (TCP/IP) and Microsoft Network

Client is added to Network.

1. Click start, then Settings, then Control Panel, then Network and Internet Connection,

then Network Connection.

2. Open Properties of Local area connection.

Click Properties.

3. Click Internet protocol (TCP/IP), then Property, then Details, then WINS and verify

Default or Enable NetBIOS over TCP/IP is selected for NetBIOS configuration.

4-40Using PRICOM in Windows Environment

Page 66

Users Manual SX

4. Verify that Microsoft Network Client is added.

-When you use TCP/ IP protocol in Windows XP, click Local Area Connection

TIP

Properties, then Advanced, then remove the check from Protect my computer and network

by limiting or preventing access to this computer from the Internet.

4-41Using PRICOM in Windows Environment

Page 67

Users Manual SX

Print Using NetBEUI, NetBIOS over TCP/IP

1. Double-click Network computer, then open work group name; [PrintServers] in the

Whole Network.

2. Select the computer you want to use.

Double-click the computer (PRICOM).

3. Select the printer.

4. Display printer configuration screen.

Double-click the printer.

Click Yes.

5. Printer add wizard to be started. Follow the instructions given by the wizard to complete

configuration. If you get the printer test page, adding printer is complete.

4-42Using PRICOM in Windows Environment

Page 68

Users Manual SX

About NetBEUI, NetBIOS over TCP/IP

File Structure of PRICOM in NetBEUI, NetBIOS over TCP/IP

environment

Ex.) : PRICOM Ethernet address: 00:80:92:34:c0:19

This section explains about the structure of NetBEUI work group installed in PRICOM.

\\Pr34c019: Computer (PRICOM)

\\Pr34c019\prn1: Printer

\\Pr34c019\report\ConfigReport.txt:

Settings report (read only)

\\Pr34c019\report\Status.txt:

Diagnostic report (read only)

\\Pr34c019\report\HardReport.txt:

System status report (read only)

\\Pr34c019\setup\Config.ini:

Initial setting file (can be edited)

\\Pr34c019\setup\WebSetup:

Shortcut file (read only)

4-43Using PRICOM in Windows Environment

Page 69

Users Manual SX

- Configuration report

Outputs the internal information in the PRICOM when activated.

- System status report

Outputs the information on PRICOM status when activated.

- Initial configuration file

With the initialization file, Work group name and IP address can be described. Use

editor like memo pad to edit and save files in the overwrite mode. In a few seconds,

PRICOM automatically resets and reboots.

By editing the initialization file and saving the file in the overwrite mode, you can change work

group name and IP address.

Ex.)

Workgroup=UserGroup

IP address=192.168.20.126

Specify work group name that already exist in the whole network. In case IP address is to be

automatically assigned by using DHCP/BOOTP and RARP server, the IP address typed in

[IP address] will be invalid.

- Shortcut file

Once PRICOM is given IP address, shortcut (WebSetup) is created. When double-

clicking the shortcut icon, web browser to be activated and PRICOM homepage to be

displayed.

- For the Web browser, refer to Chapter 8.

NOTE

- For each parameter, refer to appendix.

4-44Using PRICOM in Windows Environment

Page 70

Users Manual SX

5. Using PRICOM in UNIX/Linux Environment

This chapter explains how to configure PRICOM in a UNIX/Linux environment and how to

print using LPD and FTP.

For further information not covered in this manual, refer to the manual of the workstation you

use.

In case of initial installation and printing In case of printing

(Administrator) (Client)

Configure IP address

Configure host file

Configure printing

Configure host file

Configure printing

5-1Using PRICOM in UNIX/Linux Environment

Page 71

Users Manual SX

Configuring IP Address

-After configuring IP address, configure PRICOM by TELNET.

NOTE

Configuring IP Address by BOOTP

PRICOM will use. IP address will be configured to PRICOM by turning the power on.

TIP

For information about TELNET, refer to Chapter "8 Functions for Configuration".

-To configure IP address by BOOTP, you need a workstation that is running BOOTP within the

network.

The example below shows an IP address configuration by a UNIX BOOTP server.

Example: Ethernet address is “00809200110f”, IP address is “192.168.10.100” and host name is “pbox”.

1. Add following configuration to /etc/bootptab.

pbox:\

ht=ether:\ # Target hardware type is ETHERNET

ha=00809200110f:\ # Target hardware address

ip=192.168.10.100:\ # Target IP address

gw=192.168.10.254:\ # Default gateway address (If required)

sm=255.255.255.0: # Target subnet mask (If required)

2. Add following configuration to /etc/inetd.conf.

bootps dgram udp wait root /etc/bootpd bootpd

3. Reboot inetd.

kill -1 1

4. Reset PRICOM and printer.

5-2Using PRICOM in UNIX/Linux Environment

Page 72

Users Manual SX

Configuring IP Address by RARP

Add the combination of IP address and Ethernet address to be used by the PRICOM in UNIX

/etc/ethers and activate RARPD. IP address will be configured on PRICOM by turning the

power on.

-To configure IP address by RARP, you need a workstation that is running within the network.

TIP

The below shows an example of IP address configuration by UNIX RARP server.

Example: Ethernet address is “00809200110f”, IP address is “192.168.10.100” and host

name is “pbox”.

1. Add following configuration to /etc/ethers.

00:80:92:00:11:0f 192.168.10.100 #pbox

2. Reboot RARPD.

rarpd -a

3. Reset PRICOM and printer.

5-3Using PRICOM in UNIX/Linux Environment

Page 73

Users Manual SX

Configuring IP Address by ARP

PING.

- IP address configured in this method is temporary and will not be registered to PRICOM.

TIP

Example: Ethernet address is “00809200110f”, IP address is “192.168.10.100” and host name

is “pbox”.

1. Switch on PRICOM.

2. Register the combination of IP address and Ethernet address on the ARP table by

Be sure to register IP address by TELNET or utility.

using ARP command.

arp -s 192.168.10.100 00:80:92:00:11:0f temp

3. Command PING.

ping 192.168.10.100

4. If you get reply from PRICOM, configuration is complete.

192.168.10.100 is alive.

5-4Using PRICOM in UNIX/Linux Environment

Page 74

Users Manual SX

Configuring Host File

-Make sure to contact network administrator when editing hosts file.

-Editing hosts file may not be required if using IP administration system like DNS.

NOTE

1. Log in to UNIX/Linux machine by “root”.

# login root

2. Register PRICOM host name and IP address to /etc/hosts file.

To edit host file, use an editor, e.g. “vi”.

Example: The IP address is “192.168.10.100”, host name is “pbox”

192.168.10.98 venus # UNIX-A

192.168.10.99 mars # UNIX-B

192.168.10.100 pbox # Print-Server

3. Switch on printer. Verify the network connection by using ping command.

# ping pbox

-If there is no response or error is indicated, there may be problems with IP address configuration,

host file editing or network status. Contact network administrator.

NOTE

5-5Using PRICOM in UNIX/Linux Environment

Page 75

Users Manual SX

Printing by LPD

This section explains how to print using LPD protocol of TCP/IP.

For further information on “lpr” and “lp” commands, refer to your workstation manual.

LPD protocol:

LPD (Line Printer Daemon) is a protocol that enables you to execute printing to a printer on the

NOTE

network.

Remote-Printer Queue

PRICOM has one remote printer queues.

For printing files using printer driver, use "lp". For printing text.

FunctionRemote Printer

Direct output port lp

5-6Using PRICOM in UNIX/Linux Environment

Page 76

Users Manual SX

Using PRICOM in Solaris Environment

Solaris 2.6/7/8

This section explains how to print from Solaris2.6/7/8.

The blow command and path instruction may vary depending on OS version. Refer to your

workstation manual.

-PRICOM does not support a remote printer.

NOTE

1. Create Printer Queue

1-1 Log in to UNIX machine by “root”.

# login root

1-2 Register print server name.

Example: Register the print queue name by “pboxlp”:

# lpadmin -p pboxlp -m netstandard -o protocol=bsd

(Print queue name)

-The “lp” following “:” represents PRICOM remote printer name..

NOTE

1-3 Enable print queue.

#/usr/sbin/accept pboxlp

#/usr/bin/enable pboxlp

-o dest=pbox:lp -v /dev/null

(Host name) (Remote printer name)

5-7Using PRICOM in UNIX/Linux Environment

Page 77

Users Manual SX

2. Printing

2-1 This section explains how to print using [lp] command. For more details, refer to Solaris manual.

# lp -d pboxlp <Name of print file>

This causes the banner page to be automatically printed.

To disable the banner printing feature, add the following option, “-o nobanner”.

# lp -d pboxlp -o nobannert <Name of print file>

Alternatively, type,

# lpadmin -p pboxlp -o nobanner

directly edit the filter file generated under /etc/lp/interfaces.

Either of these options disables banner print function.

Example: Using an editor e.g. vi, open the file shown below. Change “nobanner=no” to

“nobanner=yes”.

# vi /etc/lp/interfaces/pboxlp

nobanner=no ---> nobanner=yes

3. Cancel the print request.

3-1 Use “cancel” command to cancel the current print job request.

-Depending on the timing or Solaris specification, canceling attempt will fail.

TIP

4. Check the printer status

4-1 Use “lpstat” to verify the printer status.

# lpstat -p pboxlp

-Depending on the UNIX specification, the command will fail to correctly display the printer status.

TIP

5-8Using PRICOM in UNIX/Linux Environment

Page 78

Users Manual SX

Solaris 2.3x-2.5x

This section explains how to print from Solaris 2.5 or below.

Command absolute path and configuration method may vary depending on OS version. Refer

to your workstation manual for more details.

-Remote printer can not be used with PRICOM.

TIP

1. Prepare the print queue.

1-1 Log in to the UNIX machine by “root”.

# login root

1-2 Cancel the print scheduler.

# /usr/sbin/lpshut

1-3 Register the print server.

Example: Register the host name “pbox”:

# /usr/sbin/lpsystem -R0 -t bsd pbox

1-4 Configure the print queue.

Example: Register the print queue name “pboxlp”:

#/usr/sbin/lpadmin -p pboxlp -s pbox!lp

(Name of print queue) (Name of the host) ( Name of logical printer)

When using csh, replace “/!” or “\!” with “!”.

The “lp” following “!” represents the name of the PRICOM logical printer.

NOTE

1-5 Activate the print scheduler.

#/usr/bin/sh /etc/init.d/lp start

1-6 Enable the print queue.

#/usr/sbin/accept pboxlp

#/usr/bin/enable pboxlp

5-9Using PRICOM in UNIX/Linux Environment

Page 79

Users Manual SX

2. Printing.

2-1 Print using "lp" command.

# lp -d pboxlp <Print file name>

3. Cancel the print request.

3-1 Use the “cancel” command to cancel the current print job request.

# cancel pboxlp- <Name of print file>

4. Check the printer status.

4-1 Use the “lpstat” to verify the printer status.

# lpstat -p pboxlp

-Depending on the UNIX specification, the command will fail to correctly display the printer status.

NOTE

TIP

[Limits]

When running PRICOM with Solaris 2.x, following limits occurs due to Solaris specifications.

1) If, after starting printing, the printer becomes off line and cannot receive data for quite a while,

timeout occurs on the Solaris side and when the printing continues (re-connection).the first

page will be sent again.

2) When the printer status is displayed in the form “lpstat -p<printer name>”, optional character

string returned to show the status (e.g. PrinterReady) cannot be interpreted by the Solaris. As a

result, “Faulted” is displayed followed by unintentional characters.

3) When a print-related command is sent to PRICOM while the Solaris is sending data from the

same machine, the command cannot function as it should. This is because Solaris cannot

output another packet until it finishes the transmission of the current data. Thus, “system not

responding” will be displayed in response to “lpstat -p <printer name>.

4) Certain commands such as lpstat following cancel command will result in error. In such case,

printer scheduler daemon may not be running, so verify using “lpstat -r”. If “scheduler is not

running” is displayed, reboot the printer scheduler daemon by typing in as below.

/bin/sh /etc/init.d/lp start

5) Even if “cancel” is used to delete a job that does not exist, no error occurs with Solaris.

5-10Using PRICOM in UNIX/Linux Environment

Page 80

Users Manual SX

Running PRICOM in HP-UX 9.x/10.x Environment

This section explains how to print from Hewlett-Packard HP-UX.

Command absolute path and configuration method may vary depending on OS version.

Refer to your workstation manual for more details.

1. Set the remote spooler.

When HP-UX machine is not configured to remote spooler, follow with the below configuration.

1-1 Log in to the UNIX machine by “root”.

# login root

1-2 Cancel the printer spooler.

#/usr/lib/lpshut

1-3 Register remote spooler by adding the line shown below to /etc/inetd.conf file.

printer stream tcp nowait root /usr/lib/rlpdaemon -i

1-4 Reboot inetd.

#/etc/inetd -c

2. Prepare the print queue.

2-1 Log in to the UNIX machine through “root”.

# login root

2-2 Configure print queue.

Example: Register the print queue name as “pboxlp”:

#/usr/lib/lpadmin -ppboxlp -mrmodel -ormpbox

(Print queue name)

-orplp -ocmrcmodel -osmrsmodel -ob3 -v/dev/null

(Remote printer name)

-The “lp” following “-orp” represents the name of PRICOM remote printer.

(Host name)

NOTE

5-11Using PRICOM in UNIX/Linux Environment

Page 81

Users Manual SX

2-3 Enable the print queue.

#/usr/lib/accept pboxlp

#/usr/bin/enable pboxlp

2-4 Boot the printer spooler.

#/usr/lib/lpsched

3. Prepare for printing.

3-1 Use the print command “lp”.

# lp -d pboxlp <Name of print file>

4. Cancel the print request.

4-1 Use the “cancel” command to cancel the current print job request.

# cancel pboxlp- <job number>

5. Check the printer status

5-1 Use the “lpstat” to verify the printer status.

# lpstat -p pboxlp

NOTE

-Depending on UNIX specification, the command may fail to display the printer status

correctly.

5-12Using PRICOM in UNIX/Linux Environment

Page 82

Users Manual SX

Using setnetlp Tool

-setnetlp utility is available for HP-UX, ver. 10.10 or below.

TIP

Example:

IP address: 192.168.10.100

Host name: pbox

These are already registered to /etc/hosts and to be registered by “pboxlp” as a queue name.

1. Log in by root and execute /usr/sbin/setnetlp. Below menu will be displayed. Select [1)

Add Printer]

2. The below menu will be displayed. Select [1) LP destination name:]

5-13Using PRICOM in UNIX/Linux Environment

Page 83

Users Manual SX

3. Registered printer list will be displayed. Type in printer name to be configured following

[Please enter a lp destination name:].

4. Select [2) Remote System name]. Type in the IP address configured to PRICOM, or

the host name registered to /etc/hosts after [Please enter a remote system name/ IP

address:].

Host name is typed for this example.

5. Select [Remote Printer name]. Type in [lp] following [Please enter a remote printer

name:]

5-14Using PRICOM in UNIX/Linux Environment

Page 84

Users Manual SX

6. Select [4) Local Model Script]. Model file list and prompt will be displayed. Type in

model file name to be configured following [Please enter a model file:]. [PS.nlio] that is

generally used by Japanese postscript is used for this example.

-Select “LIPS4 (LIPS3)” when using Canon LBP series.

NOTE

7. When everything is complete, the below to be displayed. Select [ 0) Done. Make

configuration now!:] if there is nothing you want to change.

-Select “ESCP” when using Epson LP series.

5-15Using PRICOM in UNIX/Linux Environment

Page 85

Users Manual SX

8. Make sure that the machine is not performing printing sequence, and then type in “y”.

9. This completes the printer addition procedure. Press [Return] key.

10. The display returns to registration confirmation screen. Enter “q” twice to quit the

setnetlp tool.

5-16Using PRICOM in UNIX/Linux Environment

Page 86

Users Manual SX

11. Execute test print to verify the proper printing operation.

Example: Printing Japanese text file

To print Japanese text file, the following options are required. (For further information, refer to HP-

UX manual.)

NOTE

Character code

To delete printer registered, the below command should be typed.

#/usr/sbin/setnetlp –x <destination>

<destination> is a registered printer name.

lp option

5-17Using PRICOM in UNIX/Linux Environment

Page 87

Users Manual SX

Using PRICOM in AIX 4.x.x Environment

This section explains how to print from IBM AIX.

Command absolute path and setting method may vary depending on OS version. Refer to

your workstation manual for more details.

1. Prepare the print queue.

1-1 Log in to the UNIX machine through “root”.

# login root

1-2 Add a print server.

Example: To add a host named “pbox”.

# ruser -a -p pbox

1-3 Start the remote printer daemon.

# startsrc -s lpd

# mkitab 'lpd:2:once:startsrc -s lpd'

1-4 Add a print queue by using smit command:

1-4-1 Once the command starts, shift to the option “Add printing queue”.

# smit mkrque

1-4-2 Among “Connection types”, select “remote”(a printer connected to a remote host).

1-4-3 Select “Standard processing” among “remote printing type".

1-4-4 Under “Add a standard remote queue”, configure the following items.

In addition, modify other options to match the conditions of the operating environment.

Example: To register the print queue under the name “pboxlp”.

Queue to be registered [pboxlp]

Host name of the remote server [pbox]

Name of the queue on the remote server [lp]

Type of print spooler on the remote server [BSD]

Printer name description on the remote server [any comment]

-“lp” in the “Queue name on the remote server” line is PRICOM remote printer name.

NOTE

5-18Using PRICOM in UNIX/Linux Environment

Page 88

Users Manual SX

2. Printing

2-1 Print using command “lp”.

# lp –d pboxlp <print file name>

3. Cancel the print request.

3-1 Use the “cancel” command to cancel the current print job request.

# cancel pboxlp- <job number>

4. Check the printer status.

4-1 Use the “lpstat” to verify the printer status.

-Depending on UNIX specification, the command may fail to display the printer status correctly.

TIP

5-19Using PRICOM in UNIX/Linux Environment

Page 89

Users Manual SX

Using PRICOM in BSD UNIX Environment

This section explains how to print from BSD UNIX.

Command absolute path and setting method may vary depending on OS version. Refer to

your workstation manual for more details.

1. Prepare the print queue.

1-1 Log in to the UNIX machine by “root”.

# login root

1-2 Register the PRICOM to /etc/printcap file.

Example: To register a print queue by the name “pboxlp”.

pboxlp:\ ----(1)

:lp=:rm=pbox:rp=lp:\ ---(2)

:sd=/usr/spool/pboxlp:\ ---(3)

:lf=/usr/spool/pboxlp/pboxlp_errs: ---(4)

(1) Describes the printer name.

(2) lp: Device file name to connect printer.

No name designation required on the network.

rm: remote printer host name.

Type the host name registered to /etc/hosts file.

rp: Remote printer name.

PRICOM remote printer name; select lp.

(3) sd: Spool directory name. Must be the absolute path.

(4) lf: Error log file name. Must be the absolute path.

1-3 Create the spool directory and error log file registered to /etc/printcap file.

Example: To create the spool directory “pboxlp” and error log file “pboxlp_errs”.

# mkdir /usr/spool/pboxlp Create the spool directory

# touch /usr/spool/pboxlp/pboxlp_errs Create the error log file

# chown -R daemon /usr/spool/pboxlp Change the owner to daemon

# chgrp -R daemon /usr/spool/pboxlp Change the group to daemon

5-20Using PRICOM in UNIX/Linux Environment

Page 90

Users Manual SX

1-4 Check whether the lpd (printer daemon) is activated.

# ps aux \ grap lpd

If lpd is not working, run the following command using a super user account.

# /usr/lib/lpd&

1-5 Enable the print queue configured.

# lpc restart pboxlp

2. Start printing.

2-1 Use the “lpr” command.

# lpr -P pboxlp <print file name>

3. Cancel the print request.

3-1 The print job request can be cancelled by using “lprm” command.

# lprm -Ppboxlp <job number>

4. Check the printer status.

4-1 The printer status can be checked by using “lpq” command.

-Certain UNIX specifications fail to display the status correctly.

TIP

-lpq short format is UNIX compatible but the long format is specific to PRICOM to display the

printer status.

Example: In case of short format

# lpd -P pboxlp

Example: In case of long format

# lpd -l -P pboxlp

5-21Using PRICOM in UNIX/Linux Environment

Page 91

Users Manual SX

Using PRICOM in Linux Environment

This section explains how to print from Linux.

Command path and settings method may vary depending on OS version. Refer to your

workstation manual for more details.

-For print queue creating tool of Red Hat Linux and Turbo Linux, refer to “Using Red Hat Linux print

queue creating tool” and “Using Turbo Linux print queue creating tool”, respectively.

NOTE

1. Prepare the print queue.

1-1 Log in to the Linux machine through “root”.

# login root

1-2 Register the PRICOM to /etc/printcap file.

Example: To register a print queue by the name “pboxlp”.

pboxlp:\ ---(1)

:lp=:rm=pbox:rp=lp:\ ---(2)

:sd=/usr/spool/pboxlp:\ ---(3)

:lf=/usr/spool/pboxlp/pboxlp_errs: ---(4)

(1) Describes the printer name.

(2) lp: Device file name to connect printer.

No name designation required on the network.

rm: Host name for the remote printer

Type the host name registered to /etc/hosts file.

rp: Remote printer name.

PRICOM remote printer name; select lp.

(3) sd: Spool directory name. Must be the absolute path.

(4) lf: Error log file name. Must be the absolute path.

1-3 Create the spool directory and error log file registered to /etc/printcap file.

Example: To create the spool directory “pboxlp” and error log file “pboxlp_errs”.

# mkdir /usr/spool/pboxlp Create the spool directory

# touch /usr/spool/pboxlp/pboxlp_errs Create the error log file

# chown -R daemon /usr/spool/pboxlp Change the owner to daemon

# chgrp -R daemon /usr/spool/pboxlp Change the group to daemon

5-22Using PRICOM in UNIX/Linux Environment

Page 92

Users Manual SX

1-4 Check whether the lpd (printer daemon) is activated.

# ps aux / grap lpd

If lpd is not working, run the following command using a super user account.

# /usr/lib/lpd&

1-5 Enable the print queue configured.

# lpc restart pboxlp

2. Start printing.

2-1 Use the “lpr” command.

# lpr -P pboxlp <print file name>

3. Cancel the print request.

3-1 The print job request can be cancelled by using “lprm” command.

# lprm –Ppboxlp <job number>

4. Check the printer status.

4-1 The printer status can be checked by using “lpq” command.

-Certain Linux specifications fail to display the status correctly.

TIP

-Short format of lpq is UNIX compatible but the long format to show the printer state is a specific to

the PRICOM.

Example: In short format

# lpd -P pboxlp

Example: In long format

# lpq -l -P pboxlp

5-23Using PRICOM in UNIX/Linux Environment

Page 93

Users Manual SX

Using Print Queue Creation Tool of Red Hat Linux

-This section explains how to print using print queue creation utility of Red Hat Linux 7.1.

TIP

Example: IP address “192.168.10.100” and Host name “pbox” are registered to etc/hosts

file and print queue is to be registered by the name “pboxlp”.

1. Select Main menu, then Programs, then System, then Setting printer.

2. Click New in the [printconf.gui] screen.

3. Click Name and alias, then type pboxlp in Printer name, then click Add.

4. Type pboxlp in Alias, then click OK.

Note that some steps may vary depending on Red Hat Linux version.

5. Click Printer type, then select LPD. Type pbox in the server and lp in the printer.

6. Select Printer driver and Printer option that correspond with your operating

environment.

7. After configuration is complete, click OK in [Printer edit].

8. Verify that the printer created is displayed and selected in the [printconf.gui].

Click Apply.

9. Verify the dialog message, “lpd has been successfully rebooted”, then Click OK.

10. Click Test in [printconf.gui] screen. When you get test page, the configuration is

complete.

5-24Using PRICOM in UNIX/Linux Environment

Page 94

Users Manual SX

Using the Print Queue Creation Tool of Turbo Linux

-This section explains how to print using print queue creation utility of Turbo Linux6.0.

TIP

Example: IP address “192.168.10.100” and Host name “pbox” are registered to etc/hosts

file and print queue is to be registered by the name “pboxlp”.

1. Select Main menu, then Turbo Linux tool, then Turbo Centro.

2. Click Turboprintcfg in the Turbo Centro-GT.

3. Click Add in Setting printer screen.

Note that some steps may vary depending on Turbo Linux version.

3-1 Select Remote LPD queue in Add printer.

3-2 Type pboxlp in New queue name.

3-3 Click Change in LPD configuration of Change printer configuration.

3-3-1 Type “pbox” in Host name.

3-3-2 Type “lp” in Queue name.

3-4 Click Change in Printer type, then select the printer driver that corresponds with your

operating environment.

3-5 Select Paper size and Color depth that correspond with your operating environment.

4. Click OK in the [Printer configuration].

5. Click Save and Finish to complete the configuration.

5-25Using PRICOM in UNIX/Linux Environment

Page 95

Users Manual SX

Printing Using FTP

This section explains how to print using FTP of TCP/IP.

For further information on “ftp” command, refer to your workstation manual.

About FTP

FTP (File Transfer Protocol) is a protocol used to transfer a file by TCP/IP. By transferring data to

NOTE

PRICOM logical directory, printing can be executed.

Logical directory

PRICOM is provided with 3 logical directories for correct printing and should be transferred by [cd]

command.

To print a file using a printer driver, go to “lp” directory; to print a text file,

Root

lp Directly output

5-26Using PRICOM in UNIX/Linux Environment

Page 96

Printing

1. Log in to PRICOM.

-When printing using “ftp” command, any input to “User” and “Password” will not disturb printing job

TIP

unless “root” is used in “User”. When the “User” name is “root”, type the password configured in

environment settings.

Example: To log in to a printer whose host name is “pbox”

(or to log in to a printer having IP address “192.168.10.100”).

#ftp pbox (or ftp 192.168.10.100 )

Connected to pbox

220 PRICOM xxxxx Ver 1.0.0 FTP Server.

User(silex:root): root

331 Password required.

Password:

230 User Logged in.

ftp>

Users Manual SX

2. Using “cd” command to move to destination directory.

-PRICOM has hierarchical structure for destination directory. Print data to the root directory is

TIP

processed as output to “lp”.

Example: To move to lp directory and verify the current directory.

ftp>cd /lp

250 Command Ok.

ftp>pwd

257 "/lp" is current directory.

ftp>

5-27Using PRICOM in UNIX/Linux Environment

Page 97

Users Manual SX

3. Changing transfer mode.

-There are two kinds for transfer mode. One is “ASCII” mode converts LF code to CR+LF code, the

other is “BINARY” mode transfers file contents. To transfer binary-converted file from the printer

NOTE

4. Transfer the print data to PRICOM using “put” command in file form.

driver, configure the transfer mode to “BINARY” (otherwise, ASCII mode is used).

Example: To change transfer mode to BINARY and verify the current mode.

ftp>type binary

200 Type set to I.

ftp>type

Using binary mode to transfer files.

ftp>

There are two formats for transferring a file using “put” command.

Example: To transfer print data “test.prn”.

ftp>put test.prn

To transfer print data to the directory specified by “/users/test/test.prn”.

ftp>put /users/test/test.prn /lp

-When printing data by specifying the directory, specify the destination logical directory.

Not necessary to move directory using the cd command.

NOTE

5. Use “quit” command to log out from PRICOM.

ftp>quit

5-28Using PRICOM in UNIX/Linux Environment

Page 98

Users Manual SX

Checking the status

-By using “stat” of "quote" command, IP address, use name for log in and transfer mode can be

NOTE

verified.

-By specifying the directory (lp) following “stat”, the printer status can be checked.

Example: To display the Ethernet board status.

ftp>quote stat

211-FTP server status:

Connected to: 192,168,10,100

User logged in: guest

Transfer type: BINARY

Data connection:Closed.

211 End of status.

ftp>

To display the printer status (directory name: lp).

ftp>quote stat /lp

211-FTP directory status:

Ready

211 End of status.

ftp>

5-29Using PRICOM in UNIX/Linux Environment

Page 99

Users Manual SX

6. Using PRICOM in NetWare

This chapter explains how to configure PRICOM and NetWare server to print from a NetWare

environment.

-For how to connect to PRICOM to printer, Refer to chapter 2.

TIP

NOTE

-Make sure the Novell client software has already been installed on the client and

NetWare server is on the network.

-Make sure to install printer driver before you start using PRICOM.

-NetWare server can be configured by either silex configuration utility (Quick Setup or

AdminManager) or Novell utility, PCONSOLE.

-When configuring by AdminManager, refer to Chapter 8.

In case of initial installation and printing In case of printing

(Administrator) (Client)

Configure using Quick Setup

Configure printer port

6-1Using PRICOM in NetWare

Page 100

Users Manual SX

Printing in NetWare Environment

Verifying NetWare Environment

When printing from a NetWare client, configuration may vary depending on NetWare

environment. For further information, contact your network administrator.

When the client is connected to the NetWare server using bindery mode:

go to 6.3

When the client machine is connected to the NetWare server using NDS mode:

go to 6.11

6-2Using PRICOM in NetWare

Silex technology SX-300U User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

INDEX

1. Introduction

Safety Instructions

2. About This Product

The Package Contents

About PRICOM SX-300U

Software Specification

Hardware Specification

Equipment Explanation

About User Software SX

3, How to Install

Prepare Items

How to Connect PRICOM to a Printer

4. Using PRICOM in Windows Environment

Print Using TCP/IP

Quick Setup

Install JC-Print2002

Adding Printer Port

Adding JC-Print2002 LPR Port

Adding JC-Print2002 IPP Port

Adding JC-Print2002 Raw (9100) Port

Configuring Printer Driver

For Windows 95/98/Me User

For Windows NT 4.0/2000/XP/Server 2003 User

Print Using Generic Function of Windows

Print Using LPR Port of Windows NT 4.0

Print Using NetBEUI, NetBIOS over TCP/IP

Verify the PC Network Configuration (NetBEUI)

For Windows 95/98/Me User

For Windows 2000 User

NetBIOS over TCP/IP

For Windows XP/Server 2003 User

Print Using NetBEUI, NetBIOS over TCP/IP

About NetBEUI, NetBIOS over TCP/IP

5. Using PRICOM in UNIX/Linux Environment

Configuring IP Address

Configuring IP Address by BOOTP

Configuring IP Address by RARP

Configuring IP Address by ARP

Configuring Host File

Printing by LPD

Using PRICOM in Solaris Environment

Solaris 2.6/7/8

Solaris 2.3x-2.5x

Running PRICOM in HP-UX 9.x/10.x Environment

Using setnetlp Tool

Using PRICOM in AIX 4.x.x Environment

Using PRICOM in BSD UNIX Environment

Using PRICOM in Linux Environment

Using Print Queue Creation Tool of Red Hat Linux

Using the Print Queue Creation Tool of Turbo Linux

Printing Using FTP

Printing

Checking the status

6. Using PRICOM in NetWare

Printing in NetWare Environment

Verifying NetWare Environment