Silex technology SDZ-330 User Manual

SALES NETWORK

•

SAMSUNG TECHWIN CO., LTD.

145-3, Sangdaewon 1-dong, Jungwon-gu, Seongnam-si,
Gyeonggi-do 462-703, Korea
TEL : [phone]~8141 FAX : [phone]

•

SAMSUNG OPTO-ELECTRONICS AMERICA,INC.
ELECTRONIC IMAGING DIV.

40 Seaview Drive, Secaucus, NJ 07094, U.S.A
TEL : [phone] FAX : [phone]

•

SAMSUNG TECHWIN MOSCOW OFFICE

Korp 14, 37-A, PR-KT, Lenningradsky, Moscow 125167, Russia
TEL : [phone],9298 FAX : [phone]

www.samsungtechwin.com
www.samsungcctv.com

•

SAMSUNG OPTO-ELECTRONICS UK, LTD.

Samsung House, 1000 Hillswood Drive, Hillswood Business
Park Chertsey, Surrey KT16 OPS
TEL : [phone] FAX : [phone]

•

TIANJIN SAMSUNG OPTO-ELECTRONICS CO., LTD.

7 Pingchang Rd, Nankai Dist. Tianjin 300190, P.R China
TEL : [phone](33821) FAX : [phone]

P/No. : Z6806-0618-01B

VAN 05. 09

High Sensitivity, Day & Night
30X Zoom Color Camera

INSTRUCTION MANUAL

SDZ-330

About this manual

Please read this manual carefully before installing and using the camera. Be sure to keep the manual handy for later reference.

The lightning flash with an arrowhead symbol, within an equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product's enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.

INFORMATION-This equipment has been tested and found to comply with limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.

WARNING -Changes or modifications not expressly approved by the manufacturer
could void the user’s authority to operate the equipment.

CAUTION : To prevent electric shock and risk of fire hazards:

Do NOT use power sources other than that specified.
Do NOT expose this appliance to rain or moisture.

This installation should be made by a qualified service person and

should conform to all local codes.

Features

30x Optical Zoom

The built-in SDZ-330 optical zoom lens is a
highly durable component. It features auto
focus, auto iris, and zoom functions.

SV-III DSP Chip

SDZ-330 features a powerful DSP that can
efficiently remove image noise, producing
crisp and clear images even under low
lighting conditions.

Fine Picture Quality under Ultra Low
Lighting

The integrated SV-III DSP Chip and 1/4" high
density CCD allows the user to capture
bright, high-quality images under ultra low
lighting conditions.

- 0.4 Lux in normal color mode.

Wide Dynamic Range (WDR)

The WDR feature offers powerful compensation
performance and thus allows for crisp, clear,
and perfect light contract under any environment.

High Resolution

Featuring 520TV line horizontal resolution in
color mode and 570TV line horizontal resolution
in BW mode, the camera features Sony's
Double Speed 410,000 pixel CCD and captures
clean, noiseless, high-quality images.

Day & Night

The camera automatically determines whether
it is night time or day time, selecting operating
mode automatically. The camera operates in
color mode during day light conditions and BW
mode in night conditions for clearer identification.

Motion Detection

Once motion is detected, the camera sends
an alert signal to the processing unit, which, if
used in conjunction with an optional alarm,
can provide effective surveillance of your
property.

Miscellaneous Functions

Other miscellaneous functions of the camera
include privacy zone masking, digital zoom, line
lock synchronization (INT/LL), freeze,
horizontal inversion, and user-configured
presets.

Control via OSD Menu and RS­485

The OSD menu and RS-485 pins allow for
remote control of the camera.
The user can also directly control the lens
using external control connection.

Warning

The camera requires regular maintenance.

Contact an authorized technician for maintenance and/or servicing.

Do not continue to use if malfunctioning.

Prolonged use of the camera in abnormal operating conditions (produces
smoke, overheats, etc.) may result in a fire.

Do not Install the camera on a surface that can not support it.

Installation on an unsuitable surface may cause the camera to fall and/or other hazards.

Do not handle the power cable with wet hands.

May result in an electric shock.

Do not disassemble the camera.

May result in a fire, electric shock, and/or other hazards.

Do not place the camera in the vicinity of inflammables.

May result in a fire and/or other hazards.

Correct Disposal of This Product (Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries with
separate collection systems) This marking shown on the product or its
literature, indicates that it should not be disposed with other household
wastes at the end of its working life. To prevent possible harm to the

environment or human health from uncontrolled waste disposal, please
separate this from other types of wastes and recycle it responsibly to promote the
sustainable reuse of material resources. Household users should contact either the
retailer where they purchased this product, or their local government office, for
details of where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions
of the purchase contract. This product should not be mixed with other commercial
wastes for disposal.

Contents

Precautions

Components and Accessories

Overview

Top
Bottom
Back

Connection

Connecting To Monitor
Connecting To Power
Connecting To Connection

8

10

11
11

12
13

14
14

15
16

Operating Your Camera

Menu Configuration
Menu Setup

• CAM TITLE

• WHITE BALANCE

• BACKLIGHT

• MOTION DETECTION

• FOCUS

• EXPOSURE

• SPECIAL

• RESET

• EXIT

Troubleshooting
Specification
Protocol Command Descripition

18
18

19
20
23

24
25
27
31
36
43
43

44
46
48

COLOR CCD CAMERACOLOR CCD CAMERA User’s ManualUser’s Manual

76

Precautions

Do not install under extreme
temperature conditions.

Use only under temperature conditions
between -10˚C and +50˚C. Provide good
ventilation when using in high temperature
conditions.

Do not install under unstable
lighting conditions.

Severe lighting changes or flickering may
hinder normal camera operation.

Do not install in high humidity
environment.

May lower image quality.

Avoid touching the camera lens.

The lens is the most important component
of the camera. Be careful not to smear it
with fingerprints.

Do not drop the camera or
subject it to physical shock.

May cause a product malfunction.

Do not expose the camera to
rain or other types of liquids.

Wipe dry any liquids. Liquids may contain
minerals that are corrosive to electronic

Never keep the camera face to
strong light directly.

May damage the CCD.

Do not expose the camera to
radioactivity.

Radioactivity exposure may damage the
CCD.

components.

Notes

• Exposure to a spotlight or an object emitting strong light may cause smear or
blooming.

• Ensure that the power source complies with normal specifications before supplying
it to the camera.

COLOR CCD CAMERACOLOR CCD CAMERA User’s ManualUser’s Manual

98

Components and Accessories

1. 30x Zoom Color Camera
SDZ-330

2. Instruction Manual

3. 6-Pin Connection Cable

4. Front Cover Ring

Overview

Top

Close

Open

Tripod Mounting Bracket Screw Hole

Used to fix tripod mounting bracket on top of the camera.

Front Cover Ring

Removable for replacement with a filter.

5. Remote Controller (Optional)

COLOR CCD CAMERACOLOR CCD CAMERA User’s ManualUser’s Manual

1110

Overview

L

Bottom

Tripod Mounting Hole

Used to install the camera on an optional tripod.
The tripod must be equipped with screws with
specifications shown on the right.

Attach the bracket to the top of the camera. Use screws
included in the package or their equivalent (less than
6mm). Otherwise, the bracket may not assemble to the
camera properly.

1/4"-20 UNC (20 THREAD)
L:4.5mm±0.2mm (ISO standard),
or 0.197" (ASA standard)

Back

Key Buttons

· Following buttons control zoom, focus, and auto focus functions.
WIDE button : To widen the view. (ZOOM OUT)
TELE button : To close in on a far object. (ZOOM IN)
F-NEAR button : To see a near object clearly.
F-FAR button : To see a far object clearly.
AF button : To activate auto focus just once.
Pressing the 'SET' button locks the zoom control function of these buttons and
prompts the main setup menu.

Notes

• The zoom postion is saved after 5 seconds when you set zoom function.

· Main setup menu can be navigated using these buttons.
SET : To access the main setup menu.
UP (WIDE button) : To move the arrow indicator to up.
DOWN (TELE button) : To move the arrow indicator to down.
LEFT (F-NEAR button) : To move the arrow indicator to left.
RIGHT (F-FAR button) : To move the arrow indicator to right.

COLOR CCD CAMERACOLOR CCD CAMERA User’s ManualUser’s Manual

1312

Overview

External Control Connector

Relates to the motion detection output signal.
Zoom and focus functions can be controlled using external siganals.

Power LED

Illuminates when power is supplied.

Video Output Jack

Used to connect an external video monitor in jack.

Communication Control Connector

Used to connect the Remote Controller (Optional). Includes external 'SYNC' signal
input pin, which is used for the line lock function.
Includes the RS-485 communication pin.

Power Input Terminal

Power supply terminal (DC12V±10%).

Frame Ground Terminal

It is the GND terminal of the motion detection signal.

Connection

Connecting to Monitor

Connect Video Out Jack to the monitor's Video In jack as shown below.

CCD Camera Monitor

• Connection methods may vary depending on the video equipment. Please
refer to the model specific instruction manual.

• Connect cables with the unit powered down.

• Set the 75Ω / Hi-Z selection switch as shown below if you have an intermediate
device.

CCD Camera

Intermediate End monitor

Connecting to Power

Connect the power cable to the camera's Power In as shown in the figure
below.

Power Input Terminal

Frame Ground

Notes

• Connect the power once the installation is complete.

• The wire is polarized. Match '+' and '-' terminals properly.

• Use a DC12V/500mA power source for SDZ-330.

COLOR CCD CAMERA User’s Manual

14

COLOR CCD CAMERA User’s Manual

15

Connection

Connecting to connection

External Control Connector

FOCUS (Input)
ZOOM (Input)

COM
MD (output)

COM

MD

Function

Tele

Wide

Far

Near

Signal Level I/O

+6V~+12V

COM

COM

-6V~-12V

+6V~+12V

COM

COM

-6V~-12V

COM

+4.0V~+5.0V

There is motion

5±0.5sec

0V

There is no motion

I

I

-

O

Connector

ZOOM

FOCUS

* MD (Motion Detection) Output Signal Level (less than 10mA)
* When using the MD function, the 'GND' should be connected to the frame ground.

Communication Control Connector

The camera can be controlled by using external controllers like a Remote
controller. (RS485 Communication)

SCC-3000

Remote Controller

SCC-100, SDZ-160CO

6-Pin Connection
Cable

* Communication Control Connector Pin Description .

Number Name Description

1 GND ­2EXT.SYNC External ‘SYNC’ Signal
3 GND -

* EXT. SYNC

60Hz ± 0.1Hz(NTSC), 50Hz ± 0.1Hz(PAL)

Number Name Description

4 TRX + RS-485 Communication
5 TRX - RS-485 Communication
6 Output Power Remote Controller only

Min: 500ns

3V or 5V
0V

* Communication Setting can set the communication setting as shown in the table below.

When you use to connect SCC-100 or SCC-3000, the default sets for SCC-100.

ITEM SCC-100 SCC-3000

MODE Serial Serial

Data Bit 8 bit 8 bit

Bit/Sec 9600bps 9600bps

Parity EVEN NON

CAM ID NO. 0 1~255

RETURN PACKET ENABLE See the SCC-3000 settigs

Notes

• Contact an authorized technician for inspection.

COLOR CCD CAMERACOLOR CCD CAMERA User’s ManualUser’s Manual

1716

Operating Y our Camera

Menu Configuration

MAIN SETUP
MENU

CAM TITLE

•OFF •ON

WHITE BAL.

•ATW •AWC •MANUAL

BACKLIGHT

•OFF •WDR

MOTION DET.

•OFF •ON

FOCUS

•MODE •ZOOM TRK MODE

•ZOOM TRK SPD • D-ZOOM •DISP ZOOM MAG

•ZOOM INIT POS •LENS INIT •END

EXPOSURE

•BRIGHTENESS •IRIS •SHUTTER

•AGC •SSNR •SENS-UP

•END

SPECIAL

•USER PRESET •PRIVACY •DAY/NIGHT

•SYNC •FREEZE •H-REV

•V-REV •IMAGE ADJ •COMMUNICATION

•END

RESET

EXIT

Menu Setup

Use the six buttons on back of the camera.

UP button
SET button

LEFT button
AF button
DOWN button
RIGHT button

1. Press the SET button to access the main setup mode.

• Main setup menu is displayed on the monitor screen.

2. Select the desired feature using the UP or DOWN button.

• Each pressing of the UP or DOWN button moves the indicator to the next
or previous feature.

• Move the arrow indicator to the desired feature item.

COLOR CCD CAMERACOLOR CCD CAMERA User’s ManualUser’s Manual

1918

Operating Y our Camera

Select feature using the UP
or DOWN button.

Change the status using the

LEFT or RIGHT button.

3. Change the status of the selected feature using the LEFT or RIGHT button.

4.

When completed, move the arrow indicator to 'EXIT' and press the SET button.

Notes

• Features marked with a have an accessible submenu.

• Access the submenu by pressing the SET button.

Cam Title

Use this feature to designate a name for the camera, which will display on the
monitor screen.

1. Press the SET button to display the main setup menu and move the arrow
indicator to 'CAM TITLE' using the UP or DOWN button.

2. Set 'CAM TITLE' to 'ON' using the LEFT or RIGHT button.

Notes

• If the CAM TITLE feature is set to 'OFF',
the name will not displayed in the monitor.

3. Press SET button.

4. You can enter up to 20 characters.
Move the cursor to the character entry field using the LEFT or RIGHT

button.

Use UP, DOWN, LEFT, and RIGHT buttons to select a desired character.

Press the SET button to confirm selection of the blinking character. The
character is then saved, and the cursor in the entry field moves to the
next position.

Repeat steps

Notes

through until the desired name has been entered.

• Correcting Mistakes

Move the cursor to 'CLR' and press the SET button to clear the entire entry.
To modify one character, use
to be modified and click the SET button after selecting the character to enter.

or to position the cursor above the character

COLOR CCD CAMERACOLOR CCD CAMERA User’s ManualUser’s Manual

2120

Operating Y our Camera

to Locate, then SETto Locate, then SET

5. Select on screen position of the CAM TITLE.
Move the cursor to 'POS' and press SET button.

The CAM TITLE is displayed on the top-left of the monitor screen.
(Default position)

FRONT DOOR

Select the position by using the 4-directional buttons, then press the SET
button to confirm the position.

FRONT DOOR

6. When completed, move the cursor to 'END' and press SET button.

White Balance Control

Your camera provides three 'WHITE BAL' control modes for your choosing in
adjusting the white balance.

1. Press the SET button to access the main setup menu and move the indicator
to 'WHITE BAL' using the UP or DOWN button.

2. Set 'WHITE BAL' using the LEFT or RIGHT button.

The three white balance control modes are as follows :

ATW(Auto Tracking White Balance): When color temperature is 1800 ~ 10500˚K,

select this mode.

AWC (Auto White balance Control): The white balance is automatically

adjusted in a specific environment. In order to obtain the best result, press
the SET button while the camera focuses on white paper. If the environment
including the light source is changed, you have to adjust the white balance
again.

Manual: To fine adjust, select the Manual mode. You can increase or decrease

the red or blue factor while monitoring the difference on the screen. Set
to 'MANUAL' mode and press the SET button. Increase or decrease the
value for red(R-Gain) and blue(B-Gain), watching the color of the picture,
and press the SET button when youobtain the best color.

COLOR CCD CAMERA User’s Manual

22

COLOR CCD CAMERA User’s Manual

23

Operating Y our Camera

Notes

• Proper White Balance may not be obtained under the following conditions.
When the scene contains mostly high color temperature object, such as a blue
sky or sunset.
When the scene is dim.
If your camera directly faces a fluorescent lamp or is used in an environment of
varying lighting conditions.

Backlight

The built-in SVIII DSP chip provides intelligent light level control to overcome the
severe ‘BACKLIGHT’ conditions.

1. Press the SET button to display the main setup menu and move the arrow
indicator to ‘BACKLIGHT’ using the UP or DOWN button.

2. SET ‘BACKLIGHT’ to the desired mode using the LEFT or RIGHT button.

WDR: Compensates for scenes simultaneously containing bright and dark elements.
OFF: Deactivation

WDR OFF

3. Select the ' WDR' mode and Press the SET button

•You can adjust the LIMIT for WDR

You can select the level(LOW,MIDDLE,HIGH). WDR sensitivity is increased or decreased.

4. When completed, press the SET button.

Notes

• The WDR mode cannot be used if 'Shutter of Exposure Menu' is set to
'MANUAL'.

• The following phenomenon may occur when operating under the WDR mode. In
such event, do not continue use under the WDR mode.

Unnatural color change or screen phenomenon.
Screen noise on bright elements.

• WDR performance vary on bright on screen elements. Adjust the camera angle
accordingly when installing the camera to compensate.

• Making changes to the WDR LIMIT may result in unnatural screen phenomenon.

Motion Detection

alert signal upon detecting motion. When used in conjunction with an external
alarm, the user can receive MD alerts. This feature is useful when monitoring
several screens simultaneously.

1. Press the SET button to access the main setup menu and move the indicator
to 'MOTION DET' using the UP or DOWN button.

2. Set 'MOTION DET' to ON using the LEFT or RIGHT button.

COLOR CCD CAMERA User’s Manual

24

COLOR CCD CAMERA User’s Manual

25

Operating Y our Camera

Press the SET button.

Increase or decrease detection sensitivity by setting the 'SENSITIVITY' value.

· When completed, press SET button.

Notes

Tips on Using the Motion Detection Feature

• Once the sensitivity level has been set, perform a test to verify proper operation
of the feature.

• The feature may not function properly under flickering light conditions.

• The camera interprets sudden changes in lighting and subsequent change in
brightness of an object as motion.

• With the feature enabled, other algorithms may require additional time to operate
than usual.

• This system does not guarantee prevention of fire or theft.
The manufacturer shall not be held responsible for any
accident or damage incurred.

• Connect an external alarm device to MD Out on back of
the camera.

FOCUS

1. Press the SET button to access the main setup manu and then position the
indicator over FOCUS using the UP or DOWN button.

2. Press the SET button.

MODE:You can select the most suitable zoom mode. Move the arrow indicator to

‘MODE’ using UP or DOWN button.

•AUTO :Select AUTO and press the SET button to confirm. Increase or decrease
optical zoom (ZOOM) or digital zoom (D­ZOOM) positions using the UP or DOWN
button while verifying the changes on screen.
Enabling D-ZOOM (ON) means that digital
zoom will activate once optical zoom ends.
Focus is automatically adjusted with moving
zoom.

COLOR CCD CAMERA User’s Manual

26

COLOR CCD CAMERA User’s Manual

27

Operating Y our Camera

•ONE PUSH : Focus is automatically adjusted just once,
after zoom position is changed. Select '
ONE PUSH' and press the SET button to
confirm. Increase or decrease optical
zoom (ZOOM) or digital zoom (D-ZOOM)
positions using the directional buttons
while verifying the changes on screen. Press the SET button once
desired image quality is obtained.

•MANUAL : Select 'MANUAL' and press the SET button

to confirm. Increase or decrease optical zoom
(ZOOM) or digital zoom (D-ZOOM) positions
using the directional buttons while verifying
the changes on screen. Press the SET button
once desired image quality is obtained. Focus
can be manually adjusted, independent of moving zoom.

ZOOM TRK MODE: You can select to use ‘ZOOM TRKMODE’. Move the arrow

indicator to ‘ZOOM TRK MODE’ using UP or DOWN button. Set
‘ZOOM TRK MODE’ to on using LEFT or RIGHT button.

ZOOM TRK SPD: Configure zoom tracing speed using this feature. Position the

indicator over 'ZOOM TRK SPEED' using the UP or DOWN button
and then set to desired mode using the LEFT or RIGHT button.

•FAST: To move zoom fast. •SLOW: To move zoom slowly.

Notes

• The 'ZOOM TRK SPEED' mode cannot be used if 'MODE' is set to 'AUTO' and
'ZOOM TRK MODE' is 'ON'.

D-ZOOM:Configure magnification limit from x1, x2, x4, or x8 using this feature.

Position the indicator over 'D-ZOOM' using the UP or DOWN button. Set 'D­ZOOM' to 'ON' and press the SET button to confirm.

· Set 'ZOOM LIMIT' to the desired level using the LEFT or

RIGHT button.

DISP ZOOM MAG:

Use this feature to display the current zoom magnification level on
screen. Position the indicator over 'DISP ZOOM MAG' using the UP
or DOWN button. Then set to ON using the LEFT or RIGHT button.

COLOR CCD CAMERA User’s Manual

28

COLOR CCD CAMERA User’s Manual

29

Operating Y our Camera

ZOOM INIT POS: Moves to the controlled ZOOM position when the power truned

on and is a function of the initial ZOOM position control.

LENS INIT : Use this feature to initialize the lens. Position the indicator over LENS

INIT. using the UP or DOWN button. Press the SET button to confirm.

END: To revert to the main setup menu.

EXPOSURE

1. Press the SET button to access the main setup menu and then position the
indicator over 'EXPOSURE' using the UP or DOWN button.

2. Press the SET button to confirm.

BRIGHTNESS: Use this feature to adjust image brightness. Position the

indicator over 'BRIGHTNESS' using the UP or DOWN button.
Then increase or decrease brightness level using the LEFT or
RIGHT button while verifying the changes on screen. Set END
once desired level is obtained.

COLOR CCD CAMERA User’s Manual

30

COLOR CCD CAMERA User’s Manual

31

Operating Y our Camera

IRIS: Set 'IRIS' to 'AUTO' or 'MANUAL'. Position the indicator over 'IRIS' using the UP

or DOWN button and then select the desired iris mode using the LEFT or RIGHT
button.

•AUTO: The iris is automatically activated upon illumination.

•MANUAL: Manual iris configuration. Set 'IRIS' to 'MANUAL' using the LEFT or

RIGHT button and then press the SET button. Increase or decrease iris
level using the LEFT or RIGHT button while verifying the changes on screen.

SHUTTER : Control image brightness by adjusting shutter speed.

1.Position the indicator over 'SHUTTER' using the UP or DOWN button. Then select
the desired shutter mode (A.FLK, ESC, MANUAL) using the LEFT or RIGHT button.

•A.FLK (NTSC: 1/100, PAL: 1/120):

Flicker-free mode

•ESC: Automatic shutter speed setting (optimal)

•MANUAL: Manual shutter speed setting

2. If you choose ‘MANUAL’, select the optimal shutter speed.

· In MANUAL mode, the optimal shutter speed needs to be designated. Select from 1/60
to 1/120,000 (NTSC) or from 1/50 to 1/120,000 (PAL).
* 'Sens-Up' mode can be configured manually (2x to 128x).

· Verify changes made to the shutter speed by referencing to changes in on screen
brightness.

3. Press the SET button to complete.

Notes

• Set the 'WDR' mode under the Backlight menu to OFF for maximum A.FLK
performance. 'A.FLK' will not function properly otherwise.

• Image may become unstable if the camera is set to 'ESC' mode and faces a strong
fluorescent light.

• Under 'ESC' mode, the brightness can be adjusted using the LEFT or RIGHT button.

• The WDR feature is not available under MANUAL mode.

• Sens-up is disabled under 'MANUAL' or 'A.FLK' mode.

COLOR CCD CAMERA User’s Manual

32

COLOR CCD CAMERA User’s Manual

33

Operating Y our Camera

AGC (Auto Gain Control): For brighter images.

1. Position the indicator over 'AGC' using the UP or DOWN button.

2. Set 'AGC' to the desired mode using the LEFT or RIGHT button.

•HIGH : Wide range gain value adjustment

•MIDDLE : Middle range gain value adjustment

•LOW : Narrow range gain value adjustment

•OFF : Disabled

SSNR(Samsung Super Noise Reduction): On screen noise reduction.

1. Position the indicator over 'SSNR' using the UP or DOWN button.

2. Set 'SSNR' to the desired mode using the LEFT or RIGHT button.

•LOW : Low noise reduction

•MIDDLE : Medium noise reduction

•HIGH :High noise reduction

•OFF : Disabled

Notes

• Changing 'AGC' setting from LOW to HIGH results in greater sensitivity, as well as
on screen noise.

• Setting 'AGC' to OFF locks 'SSNR' configuration.

SENS-UP : This feature ensures clear images at night or under low lighting

conditions.

1. Position the indicator over 'SENS-UP' using the UP or DOWN button.

2. Set 'SENS-UP' to the desired mode using the LEFT or RIGHT button.

•AUTO :Select this mode for use in night time or under low lighting conditions.

•OFF : Disabled

Notes

• Once 'AUTO' mode is set, the user can configure Sens-Up limit by increasing
/decreasing the shutter speed (e.g.: x2,...,x32, x64,..., x128).

• Enabling Sens-Up increases camera sensitivity and may result in additional noise
and/or other phenomenons. This is normal.

COLOR CCD CAMERA User’s Manual

34

COLOR CCD CAMERA User’s Manual

35

Operating Y our Camera

SPECIAL

1. Press the SET button to access the main setup menu and then position the
indicator over 'SPECIAL' using the UP or DOWN button.

2. Press the SET button to confirm.

USER PRESET:Preset user-designated configurations using this feature. Position

the indicator over 'USER PRESET' using the UP or DOWN button
and then set to 'ON' using the LEFT or RIGHT button. Press the
SET button to confirm.

•PRESET NO : Up to eight different preset configurations are supported.

•PRESET MODE: Configure initial settings under FOCUS, EXPOSURE, etc.

COLOR CCD CAMERA User’s Manual

36

COLOR CCD CAMERA User’s Manual

37

Operating Y our Camera

•PRESET SAVE: Save configured preset.

•PRESET CLEAR: Clear configured preset.

•END: Revert to the SPECIAL SETUP menu.

PRIVACY:Mask privacy area using this feature. The mask area expand/contract

upon the zoom position.

•GROUP SEL : Choose up to four groups. Each group can consist of eight mask
areas.

•MASK COLOR: Select desired mask color(BLACK, BLUE, GREEN, WHITE).

•AREA SEL : Configure eight mask areas.

•AREA MODE : Mask area display.

•TOP : To move the mask area up.

•BOTTOM : To move the mask area down.

•LEFT : To move the mask area left.

•RIGHT : To move the mask area right.

COLOR CCD CAMERA User’s Manual

38

COLOR CCD CAMERA User’s Manual

39

Operating Y our Camera

DAY/NIGHT: Select from COLOR, BW or AUTO modes.

•COLOR : Color mode.

•B/W : BW mode.

•AUTO : The camera automatically detects lighting conditions and selects the mode

accordingly.

SYNC : Two synchronization modes are available INTERNAL and EXTERNAL LINE-LOCK.

In LINE-LOCK mode, it synchronizes the camera’s video out signal to the external
SYNC signal.

•INT : Internal synchronization

•LL : External line-lock synchronization

· If you choose ‘LL’, you can adjust the desired phase.
Press the SET button.

· You can adjust the desired phase from 0 to 359.

Notes

• For NTSC models, the line-lock mode can be used if the external SYNC signal
frequency is at 60Hz.

• For PAL models, the line-lock mode can be used if the external SYNC signal
frequency is at 50Hz.

FREEZE: Use this feature to freeze capture an image. Position the indicator over 'FREEZE'

using the UP or DOWN button and then set to 'ON' using the LEFT or RIGHT
button. Press the SET button to confirm.

H-REV: Use this feature to horizontally inverse the screen. Position the indicator over

'H-REV' using the UP or DOWN button and then set to ON using the LEFT or
RIGHT button. Press the SET button to confirm.

COLOR CCD CAMERA User’s Manual

40

COLOR CCD CAMERA User’s Manual

41

Operating Y our Camera

V-REV: Use this feature to vertically inverse the screen. Position the indicator over

'V-REV' using the UP or DOWN button and then set to 'ON' using the LEFT
or RIGHT button. Press the SET button to confirm.

IMAGE ADJ:Includes image quality or special function factors.

•TONE : Increasing this value increases the overall brightness.

•SHARPNESS : Increasing this value sharpens object edges. Too high of a setting,

however, produces noise and may obscure the image.

•COLOR : Adjusting this value affects the chroma level only; the burst level is
unaffected.

COMMUNICATION: Use this feature to select communication protocol (refer to p.48~

p.53 for details). Position the indicator over 'COMMUNICATION'
using the UP or DOWN button.

•CAM ID NO. : Assign an ID number to the camera (1 to 255).
Identification number zero is used for Remote controller setup.

•CAM ID DISP: Displays camera ID on top left corner of the screen.

•BAUD RATE : Configure baud rate from 9600, 19200, or 38400bps.

•UART MODE : Configure parity bit to NON, EVEN, or ODD. Data bit is set to 8bit,

and stop bit to 1bit. Set the UART MODE to EVEN if using the Remote
Controller.

•RETURN PACKET : Used to transfer a packet.

END: evert back to the USER PRESET menu.

RESET

To reset your camera to factory default condition.

EXIT

To finish setup menu.

COLOR CCD CAMERA User’s Manual

42

COLOR CCD CAMERA User’s Manual

43

Troubleshooting

Refer to the following table if you are experiencing trouble with your camera.
Contact an authorized technician if the table does not provide you with a
solution to the trouble.

Problem

No display

Dim display

Dark display

The camera is not
functioning properly and
its surface is hot

Motion Detection
feature is not active.

Uneven colors

• Check the power cable and the wiring between the
camera and the monitor.

• Ensure proper video cable connection (Video Out
Jack).

• The lens could be dirty. Clean with a soft, clean
piece of cloth.

• Adjust monitor settings.

• Adjust camera position if exposed to a strong light
source.

•Adjust the monitor's contrast level.

•Set the intermediate device, if in use, to 75Ω/ Hi-z
(refer to p.15).

• Check the power source for compliance with
specifications.

• Ensure that the feature is set to ON.

• Check the SENSITIVITY level.

• Adjust and configure WHITE BAL.

Solution

Problem

Flickering

Can't select LL mode

LL is not function
properly.

Solution

• The camera may be facing the sun or a fluorescent
light. Adjust the position of the camera.

•The camera may be connected to a DC power
source. Connect to an AC power source.

• Check external SYNC signal frequency (should be
60Hz for NTSC, 50Hz for PAL).

COLOR CCD CAMERA User’s Manual

44

COLOR CCD CAMERA User’s Manual

45

Specifications

P

Input Voltage

O

Input Current

W

E

R

Power Consumption
Size

C
C

Total Pixels

D

Effective Pixels

O

Optics

P

Min. Focus Distance

T
I

D. ZOOM

C

S

Angle Field of view
Scanning System

S
y

Synchronization

n
c.

Frequency
Camera Title
Camera ID
Resolution
Video Output
S/N (Y signal)
Min. Illumination
WDR

E

Day & Night

L
E

Gain Control

C

White Balance

T

R

Electronic shutter speed

I

C

O.S.D

A

L

Motion Detection
SSNR
Focus
Zoom Movement Speed
Lens Initialize
Preset
Privacy Function

NTSC (SDZ-330N) PAL (SDZ-330P)

DC12V (±10%)

450 mA : Max. (Zoom,Focus, Day&night motor operating)

H : Appr. 58.0˚(Wide) to 2.22˚(Tele) V : Appr. 44.8˚(Wide) to 1.68˚(Tele)

Horizontal:15.734 KHz/Vertical :59.94 Hz Horizontal: 15.625 KHz/Vertical : 50.00 Hz

520 TV Lines(Min.) : Color 570 TV Lines(Min.) : B/W

AUTO/MANUAL (X128 ~ 1/60sec ~ 1/120,000sec)

Sens-up Limit is selectable

5.2 Sec : Wide to Tele 5.4 Sec : Wide to Tele

ON/OFF(32 Programmable Zone/ 8 Programmable Zone per Screen)

300 mA : Steady-state

3.6 W : Steady-state

1/4 inch, Vertical double density interline CCD
811(H) x 508(V) 795(H) x 596(V)
768(H) x 494(V) 752(H) x 582(V)

30X, f=3.3 to 99.0mm (F 1.6 to 3.2)

1000mm

X2, X4, X8

2:1 Interlace

Internal / Line Lock

ON/OFF (Displayed 20 characters)

255 ID Selectable

CVBS : 1.0Vp-p/75Ω

50 dB (AGC Off, Weight ON)

0.4Lux : Color 0.08Lux : B/W

AUTO/MANUAL(COLOR, B/W) (ICR type)

Low, Middle, High,OFF Selectable

ATW/AWC/Manual (1800 ˚K ~ 10,500˚K)

52dB

AUTO/MANUAL (X128 ~1/50sec ~ 1/120,000sec)

Sens-up Limit is selectable

Built-In

ON/OFF (output via Terminal)

Low, Middle, High,Off

Auto / Manual / One Push

Built-In

8-Positions

FLIP

E
L

FREEZE

E

IRIS Control

C

T

R

I
C
A

L

Control Output

Operating Temperature/Humidity
Storge Temperature/Humidity
Dimension
Weight
Option

NTSC (SDZ-330N) PAL (SDZ-330P)

LEFT/RIGHT, UP/DOWN

On/Off

Auto/Manual

RS-485(9,600bps, 19,200bps, 384,000bps Seclectable)

/ External Control by Voltage(ZOOM,FOCUS)

-10˚C to +50˚C / 20% to 80% RH

-20˚C to +60˚C / 20% to 95% RH

67.4(W) x 67.6(H) x 120(D)mm (Without Tripod Base)
450g

Remote Controller(RS-485 type)

COLOR CCD CAMERA User’s Manual

46

COLOR CCD CAMERA User’s Manual

47

Protocol Command Description

Command Name

Reset

Focus Far

Focus Near

Zoom Wide

Zoom Tele

AF Stop

One push AF

ZOOM Direct

USER PRESET Save

Function Execution Description.

Byte1 Byte2 Byte3 Byte4 || Byte5 Byte6 Byte7 Byte8 Byte9 Byte10 Byte11

Command Packet STX CAM ID HOST ADDR Command Data3 Data4 Data5 Data6 ETX CHECK SUM
Return Packet STX CAM ID HOST ADDR Response Data3 Data4 Data5 Data6 ETX CHECK SUM
Function Reset all data to factory default value.
Command Packet A0h CAM ID HOST ADDR 000Fh 00h 00h 00h 00h AFh CHECK SUM
Return Packet A0h CAM ID HOST ADDR 000Fh 00h 00h 00h 00h AFh CHECK SUM
Function Move focus lens to far direction.
Command Packet A0h CAM ID HOST ADDR 0100h 00h 00h 00h 00h AFh CHECK SUM
Return Packet A0h CAM ID HOST ADDR 0100h 00h 00h 00h 00h AFh CHECK SUM
Function Move focus lens to near direction.
Command Packet A0h CAM ID HOST ADDR 0200h 00h 00h 00h 00h AFh CHECK SUM
Return Packet A0h CAM ID HOST ADDR 0200h 00h 00h 00h 00h AFh CHECK SUM
Function Move zoom lens to wide direction.
Command Packet A0h CAM ID HOST ADDR 0040h 00h 00h 00h 00h AFh CHECK SUM
Return Packet A0h CAM ID HOST ADDR 0040h 00h 00h 00h 00h AFh CHECK SUM
Function Move wide lens to tele direction.
Command Packet A0h CAM ID HOST ADDR 0020h 00h 00h 00h 00h AFh CHECK SUM
Return Packet A0h CAM ID HOST ADDR 0020h 00h 00h 00h 00h AFh CHECK SUM
Function Stop zoom & focus lens moving.
Command Packet A0h CAM ID HOST ADDR 0000h 00h 00h 00h 00h AFh CHECK SUM
Return Packet A0h CAM ID HOST ADDR 0000h 00h 00h 00h 00h AFh CHECK SUM
Function Unconditionally execute auto focus.
Command Packet A0h CAM ID HOST ADDR 0045h 00h 00h 00h 00h AFh CHECK SUM
Return Packet A0h CAM ID HOST ADDR 0045h 00h 00h 00h 00h AFh CHECK SUM
Function

Move to ZOOM position that is set up by users
Command Packet A0h CAM ID HOST ADDR 00FFh P1 P2 P3 00h AFh CHECK SUM
Return Packet A0h CAM ID HOST ADDR 00FFh P1 P2 P3 00h AFh CHECK SUM
Parameter P1, P2 : ZOOM position set (0000h~06EAh)

P3 : D-ZOOM position set(00h~03h)

Function

Save current user preset configuration information.
Command Packet A0h CAM ID HOST ADDR 0003h P1 00h 00h 00h AFh CHECK SUM
Return Packet A0h CAM ID HOST ADDR 0003h P1 00h 00h 00h AFh CHECK SUM

COLOR CCD CAMERA User’s Manual

48

COLOR CCD CAMERA User’s Manual

49

Protocol Command Description

Parameter P1: 00h = USER PRESET 1

01h = USER PRESET 2
02h = USER PRESET 3
03h = USER PRESET 4
04h = USER PRESET 5
05h = USER PRESET 6
06h = USER PRESET 7
07h = USER PRESET 8

USER PRESET EXEC.

OSD Menu On/Off

OSD Menu Up

Function Execute selected user preset.
Command Packet A0h CAM ID HOST ADDR 0007h P1 00h 00h 00h AFh CHECK SUM
Return Packet A0h CAM ID HOST ADDR 0007h P1 00h 00h 00h AFh CHECK SUM
Parameter P1: 00h = USER PRESET 1

01h = USER PRESET 2
02h = USER PRESET 3
03h = USER PRESET 4
04h = USER PRESET 5
05h = USER PRESET 6
06h = USER PRESET 7
07h = USER PRESET 8

Function Display OSD menu on the screen.

Clear OSD menu and save current menu setup.
Command Packet A0h CAM ID HOST ADDR 00B1h P1 00h 00h 00h AFh CHECK SUM
Return Packet A0h CAM ID HOST ADDR 00B1h P1 00h 00h 00h AFh CHECK SUM
Parameter P1: 00h = ON

01h = OFF
Function Move OSD arrow to up.
Command Packet A0h CAM ID HOST ADDR 0008h 00h 00h 00h 00h AFh CHECK SUM
Return Packet A0h CAM ID HOST ADDR 0008h 00h 00h 00h 00h AFh CHECK SUM

COLOR CCD CAMERA User’s Manual

50

COLOR CCD CAMERA User’s Manual

51

Protocol Command Description

OSD Menu Down

OSD Menu Left

OSD Menu Right

OSD Menu Set

OSD Menu ESC

Function Move OSD arrow to down.
Command Packet A0h CAM ID HOST ADDR 0010h 00h 00h 00h 00h AFh CHECK SUM
Return Packet A0h CAM ID HOST ADDR 0010h 00h 00h 00h 00h AFh CHECK SUM
Function Move OSD arrow to left.
Command Packet A0h CAM ID HOST ADDR 0004h 00h 00h 00h 00h AFh CHECK SUM
Return Packet A0h CAM ID HOST ADDR 0004h 00h 00h 00h 00h AFh CHECK SUM
Function Move OSD arrow to right.
Command Packet A0h CAM ID HOST ADDR 0002h 00h 00h 00h 00h AFh CHECK SUM
Return Packet A0h CAM ID HOST ADDR 0002h 00h 00h 00h 00h AFh CHECK SUM
Functio Move to inside menu
Command Packet A0h CAM ID HOST ADDR 0100h 00h 00h 00h 00h AFh CHECK SUM
Return Packet A0h CAM ID HOST ADDR 0100h 00h 00h 00h 00h AFh CHECK SUM
Function Move to upper menu.
Command Packet A0h CAM ID HOST ADDR 0200h 00h 00h 00h 00h AFh CHECK SUM
Return Packet A0h CAM ID HOST ADDR 0200h 00h 00h 00h 00h AFh CHECK SUM

COLOR CCD CAMERA User’s Manual

52

COLOR CCD CAMERA User’s Manual

53

DECLARATION OF CONFORMITY

Application of Council Directive(s) 89 / 336 / EEC
Manufacturer's Name SAMSUNG TECHWIN CO., LTD
Manufacturer's Address SAMSUNG TECHWIN CO., LTD

42, SUNGJU-DONG CHANGWON-CITY,

KYUNGNAM, KOREA, 641-120
European Representative Name
European Representative Address
Equipment Type/Environment CCTV Camera
Model Name SDZ-330
Beginning Serial NO. S5900001
Year of Manufacture 2005. 9. 1
Conformance to EN 50081-1 : 1992

EMC-Directive 89/336 EEC and 92/31/EEC

EN 50130-4 : 1996

We, the undersigned, hereby declare that the equipment specified above conforms
to the above Directive(s).

Manufacturer SAMSUNGTECHWIN CO., LTD
Signature Signature
Full Name YOUNG TAEK SON Full Name
Position QUALITY CONTROL MANAGER Position
Place CHANGWON, KOREA Place
Date 2005. 9. 1 Date

Legal Representative in Europe

MEMO