Specifications
Main Frame (SMP-xx and MP-xx MultiViewers)
Frames
SMP-S-BASE
1RU MultiViewer frame including Power supply and networking card
and rear. Offers 5 modular slots for a combination of Video and Audio
input/output cards.
Using this frame a maximum configuration of 16 inputs to
2 independent MultiView outputs can be achieved. Alternatively, two
independent 8x2 and 4x2 MultiViewers can be housed in the frame.
SMP-R-BASE
This frame offers the same functionality as the SMP-S-BASE above but also
includes an integral 16x16 HD-SDI router (up to 3G).
NOTE: Due to the internal HD- SDI router there are restrictions on the
functionality of non-HD-SDI inputs in this frame. Therefore, this frame is only
recommended for HD-SDI applications
MP-BASE
3RU MultiViewer frame including Power supply and networking card
and rear. Offers 19 modular slots for a combination of Video and Audio
input/output cards.
Using this frame a maximum configuration of 72 inputs to
2 independent MultiView outputs can be achieved. Alternatively, up to 8
independent 4x2 plus one 8x2 MultiViewer can be housed in the
frame.
Inputs
Video Input Format
options
HDMI (with HDCP support)
HD-SDI (to 3G)
Composite Video
YUV Component Video
RGBHV (525/625 Lines Video Level)
Video Input
specifications
VIP3 or VIP3D Video scaler cards – 4 video inputs per card can accept
(with appropriate rears):
Digital:
SD-SDI (SMPTE259M 270Mb): 525/60, 625/60
HD-SDI (SMPTE292M, SMPTE424M Level A Mapping):
HDMI up to 1920x1200@60Hz
Analog:
Composite (CBVS 1V P-P), limited to 2 inputs per card: PAL, PAL-M, NTSC,
NTSC-4.43, SECAM
YUV Component (using RMP-AN4 rear max of 2 inputs per card)
RGBHV at 525/625 Lines Video level (using RMP-AN4 rear max of 2 inputs
per card)
Embedded audio
inputs
Embedded audio derived from SDI or HDMI (up to 16 channels per source)
Dolby E meter segment metadata level metering (when using optional
VIP3D scaler card)
External audio inputs
Up to 32 channels of either AES/EBU or Analog audio (AIP32AD)
LTC
SMPTE-12M unbalanced. >0.5Vpp
Outputs
Up to 1080p/60Hz or
3G MultiViewer output
The MPX-MVC-3G MultiViewer Controller card is used when you don’t need
to exceed an output resolution of 1080p/60Hz or 3G.
There is a choice of 2 MultiViewer output rears to accompany this card.
Both of these provide 2 independent outputs and a RJ-45 port for control of
the MultiViewer:
RMP-MVC-3G:
2 independent outputs
Each output offers both HDMI and HD-SDI (BNC) in parallel
Output resolutions of up to 1080p/60Hz or 3G are supported
RMP-MVC-DVI-3G:
2 independent outputs
Each output offers both DVI-D and HD-SDI (1.0/2.3 mini
connectors) in parallel
Output resolutions of up to 1080p/60Hz or 3G are supported
Up to 4K/30Hz or 6G
MultiViewer output
The MPX-MVC-6G MultiViewer Controller card is used when you need up
to 4K/30Hz or 6G output resolutions.
The following output rear accompanies this card.
RMP-MVC-6G:
2 independent outputs
Each output offers both HDMI and HD-SDI (1.0/2.3 mini
connectors) in parallel
Output resolutions of up to 4K/30Hz or 6G are supported
RJ-45 port for control of the MultiViewer
STP cage for future use for fibre outputs.
Audio
1 x Analog Stereo audio monitor output is provided via front panel mounted
headphone socket (6.35mm), with delay compensation. This may be
assigned a stereo pair from any of the non-Dolby audio sources in the first
MultiViewer instance.
For each independent MultiViewer output, up to 4 pairs (8 channels) of
audio may be selected from any of the non-dolby audio sources for
embedding onto the HDMI and SDI video Outputs.
Optional Audio output
card
Optional audio output card:
AOP32D - AES/EBU (up to 32 pairs (64 channels) per card)
Video output Standards supported
HDMI output
With embedded
audio
Slaved SDI
output
With embedded
audio
720p50
(1280x720@50Hz)
Yes
Yes
Yes
Yes
720p59.94
(1280x720@59.94Hz)
Yes
Yes
Yes
Yes
720p60
(1280x720@60Hz)
Yes
Yes
Yes
Yes
1080i 50
(1920x1080@50Hz)
Yes
Yes
Yes
Yes
1080i 59.94
(1920x1080@59.94Hz)
Yes
Yes
Yes
Yes
1080i 60
(1920x1080@60Hz)
Yes
Yes
Yes
Yes
1080p50
(1920x1080@50Hz)
Yes
Yes
Yes
Yes
1080p59.94
(1920x1080@59.94Hz)
Yes
Yes
Yes
Yes
1080p60
(1920x1080@60Hz)
Yes
Yes
Yes
Yes
2160p25 4K/25Hz
(3840x2160@25Hz)
Yes
(MVC-6G only)
Yes
(MVC-6G only)
Yes
(MVC-6G only)
Yes
(MVC-6G only)
2160p29.97 4K/29.97Hz
(3840x2160@29.97Hz)
Yes
(MVC-6G only)
Yes
(MVC-6G only)
Yes
(MVC-6G only)
Yes
(MVC-6G only)
2160p30 4K/30Hz
(3840x2160@30Hz)
Yes
(MVC-6G only)
Yes
(MVC-6G only)
Yes
(MVC-6G only)
Yes
(MVC-6G only)
XGA
(1024x768@60Hz)
Yes
1600x1200@60Hz
Yes
Latency
Processing delay varies from 2-3 fields for interlaced video inputs, 2-3
frames for progressive video inputs, depending on timing relationship
between the input and output.
Alarms
Video inputs
Loss of sync, loss of luminance, freeze frame
Audio inputs
Loss of embedded or external audio, over-level, out of phase channel pairs
Metadata inputs
Loss of VITC (SDI only), loss of V-Chip (composite only), teletext (analog
only), subtitles, video non-sync detection
Alarm indication
Visual (in display), GPI, LAN, SNMP traps
Metadata
Decoding/monitoring
Teletext (WST) subtitles (ITU-R BT.653-3) SD-SDI only
OP-47 subtitles, SD- HD- 3G-SDI
AFD driving aspect ratio (SMPTE 2016-2007), SD- HD- 3G-SDI
WSS driving aspect ratio (ETSI EN 300 294), composite only
D-VITC timecode display (SMPTE-12M-2008 VITC), SD-SDI only
ATC timecode display (SMPTE-12M-2008 ATC), SD- HD- 3G-SDI
CEA-608 closed captions. (Line 21 CEA-608 for composite NTSC or SD-
SDI, and SMPTE334-2 CDP packets (CEA-608 only) for SD- HD- 3G-SDI)
GPI I/O
Global port
8 inputs / 4 outputs per MultiViewer (assignable).
Video I/P card port
8 inputs / 4 outputs per video I/P card (assignable).
Audio Meter Scales and Ballistics
NORDIC:
Overall dynamic range: 54dB (+12 to -42dB)
Attack time: 10mSec
Decay time: 1.7Sec per 20dB decay
DIN PPM:
Overall dynamic range: 55dB (+5 to -50dB)
Attack time: 10mSec
Decay time: 1.5Sec per 20dB decay
BBC PPM:
Overall dynamic range: 24dB +3dB down "Mark 1" (+12 to
-12dB)
Attack time: 10mSec
Decay time: 2.8Sec per 24dB decay (from "Mark 7" to "Mark 1")
VU:
Overall dynamic range: 23dB (+3 to -20dB)
Attack time: 300mSec
Decay time: 300mSec per 20dB decay
VU EXT:
Overall dynamic range: 60dB (+10 to -50dB)
Attack time: 300mSec
Decay time: 300mSec per 20dB decay
AES/EBU:
Overall dynamic range: 60dB (0 to -60dB)
Attack time: < 5ms
Decay time: 1.5Sec per 20dB decay
Phase Correlation Display
Attack time: 0.4Sec for zero to ±1 deviation
Decay time: 0.4Sec for ±1 to zero deviation
Input dynamic range: 45dB
Minimum input level: -45dBu
I/O and Network Cards
Network Card
MPX-NET: Network card for SMP-xx/MP-xx Frames. This is included as
standard with the frames.
Video Input
VIP3: 4 x video inputs per card (formats as described in the video signal
inputs section earlier in the specifications)
VIP3D: As above but with added support for metering but not decoding of
Dolby® E metadata
Video Output
MPX-MVC-3G: Provides two independent outputs up to 1080p/60Hz or 3G
resolutions.
MPX-MVC-6G: Provides two independent outputs up to 4K/30Hz or 6G
resolutions.
Audio Input
AIP32A: up to 32 channels of analog audio inputs
AIP32D: up to 32 AES/EBU pairs (64 channels) of digital audio inputs
AIP32AD: up to 32 channels of analog, or digital, audio inputs
Audio Output
AOP-32D: up to 32 AES/EBU pairs (64 channels) of digital audio outputs
Rear Modules
Network rear
RMP-NET: Network rear for SMP-xx/MP-xx Frames. This is included
as standard with the frames and features:
1x BNC for reference input
1x BNC for timecode input
1x 15 way 'D' connector GPI I/O port
1x RS232/RS422 port for UMD tally via TSL
1x RJ45 auxiliary Ethernet (LAN) port
Video Inputs
RMP-HM4
4 x HDMI inputs
RMP-SD4
4 x HD-SDI inputs (on BNCs)
(Up to 2 of these can alternatively be used for Composite Video inputs.)
RMP-HM2
2 x HDMI inputs
2 x HD-SDI inputs (on BNCs or mini 1.0/2.3)
RMP-CV4
4 x Composite/HD-SDI inputs (on BNCs)
(All can accept either HD-SDI or Composite Video inputs.)
RMP-AN4-1023
Analog rear providing:
2 x RGBHV (video level) or YUV
2 x HD-SDI
All via 1.0/2.3 mini connectors
RMP-AN4-MBNC
Analog rear providing:
2 x RGBHV (video level) or YUV
2 x HD-SDI
All via Micro BNC connectors
RMP-SL4-1023
4 x Looping HD-SDI inputs.
4 x Inputs + 4 x loops provided via 8 x 1.0/2.3 mini connectors
RMP-SL4-MBNC
4 x Looping HD-SDI inputs.
4 x Inputs + 4 x loops provided via 8 x Micro BNC connectors
RMP-SR4-1023
This rear is only for use with the SMP-R-BASE integrated router frame. It
provides:
4 x HD-SDI Router/MultiViewer inputs
4 x HD-SDI router outputs
via 8 x 1.0/2.3 mini connectors
RMP-SR4-MBNC
This rear is only for use with the SMP-R-BASE integrated router frame. It
provides:
4 x HD-SDI Router/MultiViewer inputs
4 x HD-SDI router outputs
Via 8 x Micro BNC connectors
MultiViewer outputs
RMP-MVC-3G
Provides 2 independent outputs
Each output offers both HDMI and HD-SDI (BNC) in parallel
Output resolutions of up to 1080p/60Hz or 3G are supported
1x RJ45 Ethernet (LAN) connector for browser control, NTP clock
update and/or remote control of the MultiViewer outputs
RMP-MVC-DVI-3G
Provides 2 independent outputs
Each output offers both DVI-D and HD-SDI (1.0/2.3 mini connectors)
in parallel
Output resolutions of up to 1080p/60Hz or 3G are supported
1x RJ45 Ethernet (LAN) connector for browser control, NTP clock
update and/or remote control of the MultiViewer outputs
RMP-MVC-6G
Provides 2 independent outputs
Each output offers both HDMI and HD-SDI (1.0/2.3 mini connectors)
in parallel
Output resolutions of up to 4K/30Hz or 6G are supported
1x RJ45 Ethernet (LAN) connector for browser control, NTP clock
update and/or remote control of the MultiViewer outputs
STP cage reserved for future fibre output use
Audio rear
RMP-A32 rear is used to accompany any of the optional Analog or
Digital Audio input or output cards. It provides two DB-25 connectors
Front panel
Power supply and fan failure LED indicators on front panel 1 x OLED
display and control knob
1 x USB type A port
1 x 6.35mm stereo audio socket
Frame Rear Panel (SMP-xx and MP-xx)
1x IEC AC power socket
1x 2-pole DC power socket
1x RJ45 Ethernet (LAN) connector for browser control, NTP clock update
and/or remote panel control
Mechanical
SMP-xx MultiViewer
Rack Size
1RU
Details
19” Rack Mountable Frame with removable front panel, temperature
controlled fan assisted ventilation, 6 card slots, separate rear connector
modules and power supply / fan status indicators.
Variants
SMP-Rxx MultiViewer equipped with a front-end 16x16 input video router
and a stand-alone 16x16 SDI router capability.
SMP-Sxx MultiViewer without internal 16x16 SDI router
Dimensions
445mm(W) x 511mm(D) x 44mm(H)
Weight
6kg (full frame)
MP-xx MultiViewer
Rack Size
3RU
Details
19” Rack Mounting Frame with removable front panel, temperature
controlled fan assisted ventilation, 20 card slots, separate rear connector
modules and power supply / fan status indicators.
Dimensions
440mm(W) x 455mm(D) x 132mm(H)
Weight
10.5kg (full frame)
Power
SMP-xx MultiViewer
Connectors
AC - Single IEC Mains Socket
DC – Single 2-pole DC power socket
Power
Maximum power consumption 204W
Input current rating
2.5A AC, 8.5A DC
Fusing
1x 3.15A Fuse; 5x20mm ceramic body, Anti-surge/Time delay inside IEC
socket
MP-xx MultiViewer
Connectors
AC - Single IEC Mains Socket
DC – Single 2-pole DC power socket
Power
Maximum power consumption 576W
Input current rating
7A AC, 24A DC
Fusing
1x 8A Fuse; 5x20mm ceramic body, Anti-surge/Time delay inside IEC
socket
Environmental
Operating Temperature
0°C to 40°C
Relative Humidity
70% max, non-condensing
Ventilation
Fan assisted. Front Inlet, rear exhaust
Compliance
EMC – Emissions
EU: EN55103-1
USA: 47 CFR: 2009, Part 15, Sub-part B (Class A)
EMC – Immunity
EU: EN55103-1
Safety
EN: EN60950-1
USA: UL1419 (3
rd
Edition) – UL File E193966)
Hazardous Material
UK: RoHS-6 – Complies with EU Directive
Backup power supply (POWER-xx)
Front
2x Green LED indicator for presence of AC input and DC output per supply
fitted
Rear
1x 2-pole DC power outlet socket
3x IEC AC power socket (one for each supply that can be fitted)
25 way D-type (CN500) into which supplied d-type shell MUST be fitted for
DC output to be active
Mechanical
1RU Power Supply
Outline Dimensions~: 484mm(W) x 351mm(D) x 44mm(H)
Weight: up to 11kg with 3x psu fitted (one supplied as standard)
Power
Auto sensing 100 – 240 V AC, 50/60Hz switch mode 1kW power supply
with 24V DC single rail output.
Loading...