SIERRA VIDEO SMP-S-BASE, SMP-R-BASE, MP-BASE Specifications

Page 1
Specifications
Main Frame (SMP-xx and MP-xx MultiViewers)
Frames
1RU MultiViewer frame including Power supply and networking card and rear. Offers 5 modular slots for a combination of Video and Audio input/output cards. Using this frame a maximum configuration of 16 inputs to 2 independent MultiView outputs can be achieved. Alternatively, two independent 8x2 and 4x2 MultiViewers can be housed in the frame.
SMP-R-BASE
This frame offers the same functionality as the SMP-S-BASE above but also includes an integral 16x16 HD-SDI router (up to 3G). NOTE: Due to the internal HD- SDI router there are restrictions on the functionality of non-HD-SDI inputs in this frame. Therefore, this frame is only
recommended for HD-SDI applications
MP-BASE
3RU MultiViewer frame including Power supply and networking card
and rear. Offers 19 modular slots for a combination of Video and Audio input/output cards. Using this frame a maximum configuration of 72 inputs to 2 independent MultiView outputs can be achieved. Alternatively, up to 8 independent 4x2 plus one 8x2 MultiViewer can be housed in the
frame.
Inputs
Video Input Format
options
HDMI (with HDCP support) HD-SDI (to 3G) Composite Video YUV Component Video RGBHV (525/625 Lines Video Level)
Video Input
specifications
VIP3 or VIP3D Video scaler cards – 4 video inputs per card can accept
(with appropriate rears):
Digital:
SD-SDI (SMPTE259M 270Mb): 525/60, 625/60
Page 2
HD-SDI (SMPTE292M, SMPTE424M Level A Mapping): HDMI up to 1920x1200@60Hz
Analog:
Composite (CBVS 1V P-P), limited to 2 inputs per card: PAL, PAL-M, NTSC,
NTSC-4.43, SECAM YUV Component (using RMP-AN4 rear max of 2 inputs per card)
RGBHV at 525/625 Lines Video level (using RMP-AN4 rear max of 2 inputs
per card)
Embedded audio
inputs
Embedded audio derived from SDI or HDMI (up to 16 channels per source)
Dolby E meter segment metadata level metering (when using optional
VIP3D scaler card)
External audio inputs
Up to 32 channels of either AES/EBU or Analog audio (AIP32AD)
LTC
SMPTE-12M unbalanced. >0.5Vpp
Outputs
Up to 1080p/60Hz or
3G MultiViewer output
The MPX-MVC-3G MultiViewer Controller card is used when you don’t need
to exceed an output resolution of 1080p/60Hz or 3G.
There is a choice of 2 MultiViewer output rears to accompany this card. Both of these provide 2 independent outputs and a RJ-45 port for control of
the MultiViewer:
RMP-MVC-3G:
2 independent outputs Each output offers both HDMI and HD-SDI (BNC) in parallel Output resolutions of up to 1080p/60Hz or 3G are supported
RMP-MVC-DVI-3G:
2 independent outputs Each output offers both DVI-D and HD-SDI (1.0/2.3 mini
connectors) in parallel
Output resolutions of up to 1080p/60Hz or 3G are supported
Up to 4K/30Hz or 6G
MultiViewer output
The MPX-MVC-6G MultiViewer Controller card is used when you need up
to 4K/30Hz or 6G output resolutions.
The following output rear accompanies this card.
RMP-MVC-6G:
2 independent outputs Each output offers both HDMI and HD-SDI (1.0/2.3 mini
connectors) in parallel
Output resolutions of up to 4K/30Hz or 6G are supported RJ-45 port for control of the MultiViewer STP cage for future use for fibre outputs.
Audio
1 x Analog Stereo audio monitor output is provided via front panel mounted headphone socket (6.35mm), with delay compensation. This may be
Page 3
assigned a stereo pair from any of the non-Dolby audio sources in the first
MultiViewer instance.
For each independent MultiViewer output, up to 4 pairs (8 channels) of audio may be selected from any of the non-dolby audio sources for
embedding onto the HDMI and SDI video Outputs.
Optional Audio output
card
Optional audio output card:
AOP32D - AES/EBU (up to 32 pairs (64 channels) per card)
Video output Standards supported
HDMI output
With embedded
audio
Slaved SDI
output
With embedded
audio
720p50
(1280x720@50Hz)
Yes
Yes
Yes
Yes
720p59.94
(1280x720@59.94Hz)
Yes
Yes
Yes
Yes
720p60
(1280x720@60Hz)
Yes
Yes
Yes
Yes
1080i 50
(1920x1080@50Hz)
Yes
Yes
Yes
Yes
1080i 59.94
(1920x1080@59.94Hz)
Yes
Yes
Yes
Yes
1080i 60
(1920x1080@60Hz)
Yes
Yes
Yes
Yes
1080p50
(1920x1080@50Hz)
Yes
Yes
Yes
Yes
1080p59.94
(1920x1080@59.94Hz)
Yes
Yes
Yes
Yes
1080p60
(1920x1080@60Hz)
Yes
Yes
Yes
Yes
2160p25 4K/25Hz
(3840x2160@25Hz)
Yes
(MVC-6G only)
Yes
(MVC-6G only)
Yes
(MVC-6G only)
Yes
(MVC-6G only)
2160p29.97 4K/29.97Hz
(3840x2160@29.97Hz)
Yes
(MVC-6G only)
Yes
(MVC-6G only)
Yes
(MVC-6G only)
Yes
(MVC-6G only)
2160p30 4K/30Hz
(3840x2160@30Hz)
Yes
(MVC-6G only)
Yes
(MVC-6G only)
Yes
(MVC-6G only)
Yes
(MVC-6G only)
XGA
(1024x768@60Hz)
Yes

1600x1200@60Hz
Yes

Latency
Processing delay varies from 2-3 fields for interlaced video inputs, 2-3 frames for progressive video inputs, depending on timing relationship
between the input and output.
Page 4
Alarms
Video inputs
Loss of sync, loss of luminance, freeze frame
Audio inputs
Loss of embedded or external audio, over-level, out of phase channel pairs
Metadata inputs
Loss of VITC (SDI only), loss of V-Chip (composite only), teletext (analog
only), subtitles, video non-sync detection
Alarm indication
Visual (in display), GPI, LAN, SNMP traps
Metadata
Decoding/monitoring
Teletext (WST) subtitles (ITU-R BT.653-3) SD-SDI only OP-47 subtitles, SD- HD- 3G-SDI AFD driving aspect ratio (SMPTE 2016-2007), SD- HD- 3G-SDI WSS driving aspect ratio (ETSI EN 300 294), composite only D-VITC timecode display (SMPTE-12M-2008 VITC), SD-SDI only ATC timecode display (SMPTE-12M-2008 ATC), SD- HD- 3G-SDI
CEA-608 closed captions. (Line 21 CEA-608 for composite NTSC or SD-
SDI, and SMPTE334-2 CDP packets (CEA-608 only) for SD- HD- 3G-SDI)
GPI I/O
Global port
8 inputs / 4 outputs per MultiViewer (assignable).
Video I/P card port
8 inputs / 4 outputs per video I/P card (assignable).
Audio Meter Scales and Ballistics
NORDIC:
Overall dynamic range: 54dB (+12 to -42dB) Attack time: 10mSec Decay time: 1.7Sec per 20dB decay
DIN PPM:
Overall dynamic range: 55dB (+5 to -50dB) Attack time: 10mSec Decay time: 1.5Sec per 20dB decay
BBC PPM:
Overall dynamic range: 24dB +3dB down "Mark 1" (+12 to
-12dB) Attack time: 10mSec Decay time: 2.8Sec per 24dB decay (from "Mark 7" to "Mark 1")
VU:
Overall dynamic range: 23dB (+3 to -20dB) Attack time: 300mSec Decay time: 300mSec per 20dB decay
VU EXT:
Overall dynamic range: 60dB (+10 to -50dB) Attack time: 300mSec Decay time: 300mSec per 20dB decay
AES/EBU:
Overall dynamic range: 60dB (0 to -60dB) Attack time: < 5ms Decay time: 1.5Sec per 20dB decay
Phase Correlation Display
Attack time: 0.4Sec for zero to ±1 deviation Decay time: 0.4Sec for ±1 to zero deviation Input dynamic range: 45dB Minimum input level: -45dBu
Page 5
I/O and Network Cards
Network Card
MPX-NET: Network card for SMP-xx/MP-xx Frames. This is included as
standard with the frames.
Video Input
VIP3: 4 x video inputs per card (formats as described in the video signal
inputs section earlier in the specifications)
VIP3D: As above but with added support for metering but not decoding of
Dolby® E metadata
Video Output
MPX-MVC-3G: Provides two independent outputs up to 1080p/60Hz or 3G
resolutions.
MPX-MVC-6G: Provides two independent outputs up to 4K/30Hz or 6G
resolutions.
Audio Input
AIP32A: up to 32 channels of analog audio inputs AIP32D: up to 32 AES/EBU pairs (64 channels) of digital audio inputs AIP32AD: up to 32 channels of analog, or digital, audio inputs
Audio Output
AOP-32D: up to 32 AES/EBU pairs (64 channels) of digital audio outputs
Rear Modules
Network rear
RMP-NET: Network rear for SMP-xx/MP-xx Frames. This is included
as standard with the frames and features: 1x BNC for reference input 1x BNC for timecode input 1x 15 way 'D' connector GPI I/O port 1x RS232/RS422 port for UMD tally via TSL 1x RJ45 auxiliary Ethernet (LAN) port
Video Inputs
RMP-HM4
4 x HDMI inputs
RMP-SD4
4 x HD-SDI inputs (on BNCs)
(Up to 2 of these can alternatively be used for Composite Video inputs.)
RMP-HM2
2 x HDMI inputs 2 x HD-SDI inputs (on BNCs or mini 1.0/2.3)
RMP-CV4
4 x Composite/HD-SDI inputs (on BNCs)
(All can accept either HD-SDI or Composite Video inputs.)
RMP-AN4-1023
Analog rear providing:
2 x RGBHV (video level) or YUV 2 x HD-SDI
All via 1.0/2.3 mini connectors
RMP-AN4-MBNC
Analog rear providing:
2 x RGBHV (video level) or YUV 2 x HD-SDI
All via Micro BNC connectors
RMP-SL4-1023
4 x Looping HD-SDI inputs.
4 x Inputs + 4 x loops provided via 8 x 1.0/2.3 mini connectors
RMP-SL4-MBNC
4 x Looping HD-SDI inputs.
4 x Inputs + 4 x loops provided via 8 x Micro BNC connectors
RMP-SR4-1023
This rear is only for use with the SMP-R-BASE integrated router frame. It provides:
4 x HD-SDI Router/MultiViewer inputs 4 x HD-SDI router outputs
via 8 x 1.0/2.3 mini connectors
RMP-SR4-MBNC
This rear is only for use with the SMP-R-BASE integrated router frame. It provides:
4 x HD-SDI Router/MultiViewer inputs 4 x HD-SDI router outputs
Via 8 x Micro BNC connectors
Page 6
MultiViewer outputs
RMP-MVC-3G
Provides 2 independent outputs Each output offers both HDMI and HD-SDI (BNC) in parallel Output resolutions of up to 1080p/60Hz or 3G are supported 1x RJ45 Ethernet (LAN) connector for browser control, NTP clock
update and/or remote control of the MultiViewer outputs
RMP-MVC-DVI-3G
Provides 2 independent outputs Each output offers both DVI-D and HD-SDI (1.0/2.3 mini connectors)
in parallel
Output resolutions of up to 1080p/60Hz or 3G are supported 1x RJ45 Ethernet (LAN) connector for browser control, NTP clock
update and/or remote control of the MultiViewer outputs
RMP-MVC-6G
Provides 2 independent outputs Each output offers both HDMI and HD-SDI (1.0/2.3 mini connectors)
in parallel
Output resolutions of up to 4K/30Hz or 6G are supported 1x RJ45 Ethernet (LAN) connector for browser control, NTP clock
update and/or remote control of the MultiViewer outputs
STP cage reserved for future fibre output use
Audio rear
RMP-A32 rear is used to accompany any of the optional Analog or Digital Audio input or output cards. It provides two DB-25 connectors
Front panel
Power supply and fan failure LED indicators on front panel 1 x OLED
display and control knob 1 x USB type A port 1 x 6.35mm stereo audio socket
Frame Rear Panel (SMP-xx and MP-xx)
1x IEC AC power socket 1x 2-pole DC power socket
1x RJ45 Ethernet (LAN) connector for browser control, NTP clock update
and/or remote panel control
Mechanical
SMP-xx MultiViewer
Rack Size
1RU
Details
19” Rack Mountable Frame with removable front panel, temperature controlled fan assisted ventilation, 6 card slots, separate rear connector
modules and power supply / fan status indicators.
Variants
SMP-Rxx MultiViewer equipped with a front-end 16x16 input video router
and a stand-alone 16x16 SDI router capability. SMP-Sxx MultiViewer without internal 16x16 SDI router
Dimensions
445mm(W) x 511mm(D) x 44mm(H)
Weight
6kg (full frame)
MP-xx MultiViewer
Rack Size
3RU
Page 7
Details
19” Rack Mounting Frame with removable front panel, temperature controlled fan assisted ventilation, 20 card slots, separate rear connector
modules and power supply / fan status indicators.
Dimensions
440mm(W) x 455mm(D) x 132mm(H)
Weight
10.5kg (full frame)
Power
SMP-xx MultiViewer
Connectors
AC - Single IEC Mains Socket DC – Single 2-pole DC power socket
Power
Maximum power consumption 204W
Input current rating
2.5A AC, 8.5A DC
Fusing
1x 3.15A Fuse; 5x20mm ceramic body, Anti-surge/Time delay inside IEC
socket
MP-xx MultiViewer
Connectors
AC - Single IEC Mains Socket DC – Single 2-pole DC power socket
Power
Maximum power consumption 576W
Input current rating
7A AC, 24A DC
Fusing
1x 8A Fuse; 5x20mm ceramic body, Anti-surge/Time delay inside IEC
socket
Environmental
Operating Temperature
0°C to 40°C
Relative Humidity
70% max, non-condensing
Ventilation
Fan assisted. Front Inlet, rear exhaust
Compliance
EMC – Emissions
EU: EN55103-1 USA: 47 CFR: 2009, Part 15, Sub-part B (Class A)
EMC – Immunity
EU: EN55103-1
Safety
EN: EN60950-1
USA: UL1419 (3
rd
Edition) – UL File E193966)
Hazardous Material
UK: RoHS-6 – Complies with EU Directive
Backup power supply (POWER-xx)
Front
2x Green LED indicator for presence of AC input and DC output per supply
fitted
Rear
1x 2-pole DC power outlet socket
3x IEC AC power socket (one for each supply that can be fitted)
25 way D-type (CN500) into which supplied d-type shell MUST be fitted for
DC output to be active
Page 8
Mechanical
1RU Power Supply Outline Dimensions~: 484mm(W) x 351mm(D) x 44mm(H) Weight: up to 11kg with 3x psu fitted (one supplied as standard)
Power
Auto sensing 100 – 240 V AC, 50/60Hz switch mode 1kW power supply
with 24V DC single rail output.
Loading...