![](/html/9f/9faf/9fafec429e85cd9379bc5e1fb154c750c814c8fc08b4e616b93b1604d01605e8/bg1.png)
1
Safety instructions
– The washing machine is heavy - take care when lifting.
– Caution: frozen hoses may rip/burst. Do not install the washing machine in areas exposed
to frost or outdoors.
– The washing machine could be damaged. Do not lift the appliance by protruding
components (e.g. the washing machine door, the cover, the front panel or the outer door
in case of deco models).
– In addition to the instructions provided in this document, special regulations from the
relevant water and electric utility companies may apply.
– If in doubt, have a technician connect the appliance.
– Lay hoses and cables in such a way that there is no risk of tripping.
Installation surface
– The machine must be stable so that it does not move around.
– The installation surface must be firm and level.
– Soft floors/floor coverings are not suitable.
Installation on a pedestal
– The feet of the washing machine must be secured with holding brackets*.
* order no. WMZ20455, WZ20455
Installation on a wood joist floor
– If possible, place the washing machine in a corner.
– Screw a water-resistant wooden board (min. 30 mm thick) to the floor.
– The feet of the washing machine must be secured with holding brackets*.
* order no. see above
Installation on a platform with drawer*
– * order no.WMZ20455, WZ20455
Installing the appliance
Install the appliance before connecting it to the power supply.
Installation in a kitchenette (underneath the worktop or fitted in a cabinet)
– Recess width of 60 cm required.
– Only install the washing machine underneath a continuous worktop that is securely
connected to adjacent cabinets.
2
Scope of delivery depending on model
Also required, depending on the connection:
– 1 hose clamp Ø 24-40 mm (exclusive dealers) to connect to a siphon
apage 4; water connection.
Useful tools
– Spirit level for installation.
– Wrenches
WAF 13: for loosening transport braces apage 3 and
WAF 17: for aligning appliance feet apage 5.
Hose and cable lengths depending on model
Left-hand connection
or
Right-hand connection
Available from specialist dealers/the after-sales service:
– Extension for Aqua-Stop or cold-water inlet hose (approx. 2.50 m),
order no. WMZ2380, WZ10130, CZ11350, Z7070X0
– Longer inlet hose (approx. 2.20 m) for standard model.
Mains cable
Water outlet
Water inlet
Elbow
for fixing the drainage
hose in place
Covers
AquaäStop Hot water
AquaäSecure &
Standard
Adapter 1/2’’-3/4’’
(depending on model)
~
145 cm
~
100 cm
~
100 cm
~
135 cm
~
145 cm
min. 60 cm
max. 100 cm
~
90 cm
Moisture inside the drum
is due to final testing.
3
Removing the transport braces
– Before using the appliance for the first time, make sure that you
completely remove transport braces and keep them for
subsequent transportation.
– If you need to transport the appliance at a later date, always re-affix
the transport braces to prevent damage to the machine.
apage 6.
– Store the screw and sleeve together.
1. Take the hoses out of the holders.
2. Remove all 4 screws completely.
3. Remove all 4 transport braces completely and take the mains cable
out of the holders (depending on model).
4. Affix the covers.
Water connection depending on model
– Risk of electric shock. Do not immerse the Aqua-Stop safety device in water
(contains an electric valve).
– To prevent leaks or water damage, observe the instructions in this section.
– Caution: only operate the washing machine using cold drinking water (in case of models
featured for hot water: maximum temperature 60 ºC).
– Do not connect to the mixer tap of an unpressurised hot-water boiler.
– Do not use a used inlet hose. Only use the inlet hose supplied or one which was
purchased from an authorised specialist dealer.
– If in doubt, have a technician connect the appliance.
4
Water connection depending on model
Q
Water inlet
Caution: do not bend, squash, modify or cut through
(otherwise its strength is no longer guaranteed).
Optimum water pressure in the supply network: 200ä1,000 kPa (2ä10 bar)
– When the tap is on, the water flow is at least 10 l/min
(1-2 bar: 6 l/min; with 1 bar consumption parameters cannot be assure).
– If the water pressure is higher than this, a pressure reducing valve must be installed
Connection to the tap:
Aqua-Stop, Aqua-Secure, Standard:
Connection to the
machine:
AquaäStop, Aqua-Secure Standard
no necessary with AquaStop, fixed installation;
Aqua-Secure, Standard
1. Connect the water inlet hose (hoses) to the tap (taps) 3/4" = 26,4 mm and to the solenoid
valves.
Caution: only tighten the screw connections by hand.
2. Open the water tap (taps) carefully, checking the leak tightness of the connection points.
Caution: the screw connection is under mains water pressure.
Connection in case of hot water
models:
COLD – Cold water
HOT – Hot water max. 60 °C (red)
Q
Water outlet
Caution: do not bend or pull lengthways.
Height difference between the installation surface and the
drain:
min. 60 cm - max. 100 cm
Outlet in a sink:
Caution: secure the drain hose from slipping out.
Caution: the plug must not block drainage from the sink. During
pumping, check whether the water is draining away quickly
enough. The end of the drain hose must not be immersed in the
water pumped out. This risks water being sucked back into the
washing machine.
Drainage into a siphon:
Caution: the connection point must be secured with a hose
clamp, Ø 24-40 mm (exclusive dealers).
![](/html/9f/9faf/9fafec429e85cd9379bc5e1fb154c750c814c8fc08b4e616b93b1604d01605e8/bg2.png)
5
Manufacturer –> Operating instructions
Alignment
Intense noise formation, vibrations and “wandering” may be the result of incorrect
alignment.
Aligning the washing machine with a spirit level
1. Loosen the lock nut using a wrench, by turning it in a clockwise direction.
2. Change the height by turning the appliance feet.
Caution: all four appliance feet must be firmly on the ground.
The washing machine must not wobble.
Check the alignment of the washing machine with a spirit level and adjust
if necessary.
3. Tighten the lock nut against the housing.
In doing so, hold the foot tight and do not adjust its height.
Caution: the lock nuts on all four appliance feet must be screwed tightly
against the housing.
Electrical connection
ʑ
The washing machine must only be connected to an alternating current via a
properly installed earthed socket.
ʑ
The power supply and voltage indicated on the washing machine (rating plate)
must be the same.
ʑ
The connected load and fuse required are specified on the rating plate.
ʑ
Make sure that:
– the mains plug fits the socket,
– the cable cross-section is adequate,
– the earthing system is properly installed.
ʑ
(If this is necessary), the mains cable may only be replaced by a qualified
electrician.
Replacement mains cables are available from the after-sales service.
ʑ
Do not use multiple plugs/couplings or extension cables.
ʑ
If a residual current circuit breaker is used, only use a type which displays this
symbol: ‚.
Only this symbol guarantees compliance with the currently applicable regulations.
ʑ
Do not plug in or unplug the mains plug with wet hands.
Pull the appliance plug out of the socket at the plug only, not by the cable.
9008 / 9000502633
9000502633
6
Transportation, e.g. when moving home
Before transporting the washing machine:
1. Turn off the tap.
2. Drain residual water
aOperating instructions; Maintenance - drain pump.
3. Release the water pressure in the inlet hose
aOperating instructions; Maintenance - filter
in water inlet.
4. Disconnect the washing machine from the power supply.
5. Dismantle the hoses.
Preparing and installing transport braces:
1.2.Remove all covers and store them.
Affix all transport braces. In doing so, turn the
bend on the hose holders inwards. Clamp the
mains cable in the holders. Tighten the screws.
After transportation, the transport braces must be removed. apage 3.
To prevent unused detergent from flowing straight into the drain during the next wash: Pour
2 litres of water into compartment II and start the Empty programme.
Technical specifications
ʑ
Dimensions (width x depth x height) 60 x 55 x 85 cm
ʑ
Weight 66 – 73 kg depending on model
ʑ
Mains connection Nominal voltage 220-240 V, 50 Hz
Nominal current 10 A
Nominal power 2,300 W
ʑ
Water pressure 200-1000 kPa (2-10 bar)
7
After-sales service
ʑ
If you cannot rectify the fault yourself (Operating instructions; What to do if... apage 11),
please contact our after-sales service. We will always find a suitable solution and will avoid a
visit from a service technician wherever possible.
ʑ
The contact details for all countries can be found in the enclosed after-sales service directory.
ʑ
Please give the after-sales service the product number (E-Nr.) and the production number
(FD) of the appliance.
Product number Production number
You will find this information on the inside of the
washing machine door, on the opened service
flap or at the rear of the appliance (depending
on the model).
ʑ
Rely on the professionalism of the manufacturer. Please contact us.
This will ensure that the repair is carried out by trained service technicians who arrive
equipped with genuine spare parts for your appliance.
Aqua-Stop warranty only for appliances with Aqua-Stop
In addition to warranty claims against the vendor from the purchase agreement and to our
appliance warranty, we will pay damages under the following conditions:
1. If a fault in our Aqua-Stop system causes water damage, we will reimburse damages caused
to private customers.
2. The liability guarantee is valid for the service life of the appliance.
3. It is a prerequisite of all warranty claims that the appliance with Aqua-Stop must have been
set up and connected correctly in accordance with our instructions; this also includes a
correctly fitted Aqua-Stop extension (original accessories).
Our warranty goes not cover defective power cables or fittings between the Aqua-Stop
connection and the tap.
4. Appliances with Aqua-Stop do not need to be supervised during operation, nor secured
afterwards by turning off the tap.
The tap only needs to be turned off if you are away from home for a long period, e.g. for
several weeks' holiday.
Washing machine
Contents Page
ʋSafety instructions . . . . . . . . . . . . . . . . . . . . . . . . . 1
ʋInstallation surface. . . . . . . . . . . . . . . . . . . . . . . . . 1
ʋInstalling the appliance . . . . . . . . . . . . . . . . . . . . . 1
ʋScope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . 2
ʋHose and cable lengths . . . . . . . . . . . . . . . . . . . . 2
ʋRemoving the transport braces . . . . . . . . . . . . . . . 3
ʋWater connection . . . . . . . . . . . . . . . . . . . . . . . .3/4
ʋAlignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
ʋElectrical connection . . . . . . . . . . . . . . . . . . . . . . . 5
ʋTransportation, e.g. when moving home . . . . . . . . 6
ʋTechnical specifications. . . . . . . . . . . . . . . . . . . . . 6
ʋAfter-sales service . . . . . . . . . . . . . . . . . . . . . . . . . 7
ʋAqua-Stop warranty . . . . . . . . . . . . . . . . . . . . . . . . 7
Installation
instructions
Read these instructions before switching on the washing machine.
Also observe the separate Instruction manual.
Keep all documents for use in the future or for the subsequent owner.
en