the home and only for its
designated purpose: for
washing domestic dishes.
■ This appliance is intended
for use up to a maximum
altitude of 2500 metres
above sea level.
( Safety instructions
Safety instructions
This appliance may be used by
children over the age of 8 years
old and by persons with
reduced physical, sensory or
mental capabilities or by
persons with a lack of
experience or knowledge if they
are supervised or are instructed
by a person responsible for
their safety how to use the
appliance safely and have
understood the associated
hazards.
Children must not play with, on,
or around the appliance.
Children must not clean the
appliance or carry out general
maintenance unless they are at
least 8 years old and are being
supervised.
Keep children below the age of
8 years old at a safe distance
from the appliance and power
cable.
Before you switch ON the
appliance
Please read the instructions for
use and installation carefully.
They contain important
information on how to install,
use and maintain the appliance.
Retain all documents for later
use or for the subsequent
owner.
You can download the
instructions for use from our
website free of charge. The
relevant Internet address can
be found overleaf on these
instructions for use.
Delivery
1. Check the packaging and
dishwasher immediately for
damage caused in transit.
Do not switch on a damaged
appliance, but contact your
supplier.
2. Please dispose of the
packaging material in an
environmentally friendly
manner.
3. Do not let children play with
packaging and its parts.
There is a risk of suffocation
from collapsible boxes and
film.
5
en Safety instructions
Installation
■ Following installation, ensure
that the back of the
dishwasher is not freely
accessible (protection
against contact due to hot
surface).
■ Install and connect the
appliance according to the
installation and assembly
instructions.
■ Prior to installation,
disconnect the dishwasher
from the power supply.
■ Ensure that the protective
conductor system of the
domestic supply has been
correctly installed.
■ The electrical connection
conditions must correspond
with the specifications on the
dishwasher rating plate 9J.
■ If the power cord of this
appliance is damaged, it
must be replaced with a
particular power cord.
To prevent injury, the power
cord may be purchased from
customer service only.
■ If the dishwasher is installed
in a high-sided unit, the unit
must be secured properly.
■ If the dishwasher is installed
below or above other
domestic appliances, follow
the information for
installation in combination
with a dishwasher in the
installation instructions for
the particular appliances.
■ Also follow the installation
instructions for the
dishwasher to ensure that all
appliances are operated
safely.
■ If there is no information or if
the installation instructions
do not include the
appropriate information,
contact the manufacturer of
these appliances to ensure
that the dishwasher can be
installed above or below
these appliances.
■ If you cannot obtain any
information from the
manufacturer, you must not
install the dishwasher above
or below these appliances.
■ If you install a microwave
oven above the dishwasher,
the microwave oven may be
damaged.
■ Install built-under or
integratable appliances only
under continuous worktops
which have been screwed to
adjacent cupboards to
ensure stability.
■ Do not install the appliance
near heat sources (radiators,
heat storage tanks, cookers
or other appliances which
generate heat) and do not
install under a hob.
6
Safety instructions en
■ Please note that the
insulation material of the
dishwasher power cord may
melt next to heat sources
(e.g. heating / hot water
installations) or hot
appliance parts. Make sure
that the power cord of the
dishwasher never comes into
contact with heat sources or
hot appliance parts.
■ After installing the appliance,
ensure that the plug is easily
accessible. ~ "Electrical
connection" on page 56
■ For some models:
The plastic housing on the
water connection contains an
electric valve. The supply
hose contains electrical
connection cables. Do not
cut through the supply hose.
Do not immerse the plastic
housing in water.
Childproof lock (door lock) *
Door lock
The child-proof lock (door lock)
protects children from potential
hazards which the dishwasher
poses.
:Warning
Risk of suffocation!
Children may become locked in
the dishwasher and suffocate.
Always completely close the
appliance door when leaving
the dishwasher.
Activate the child-proof lock
(door lock) as follows:
1. Pull the catch of the
child-proof lock towards
yourself (1).
2. Close the door (2).
The child-proof lock is
activated.
In daily use
Read and observe the safety
information and instructions for
use on the packaging for
cleaning and rinsing agents.
Ensure that you follow the
safety instructions, even when
operating the appliance via the
Home Connect app, which are
out of sight when you are away
from home. Follow the
instructions in the app.
7
en Safety instructions
Open the door with activated
child-proof lock (door lock) as
follows:
1. Press the catch of the
child-proof lock to the right
(1).
2. Open the door (2).
Deactivate the child-proof lock
(door lock) as follows:
1. Press the catch of the
child-proof lock to the right
(1).
2. Press the catch of the
child-proof lock backwards
(2).
The childproof lock is
deactivated.
Child-proof lock (button lock)
Button lock
You can prevent your
dishwasher being switched off
inadvertently (e.g. by children
pressing the buttons).
Here’s how to activate the
button lock:
1. Start the desired
programme.
2. Press and hold the F button
for about 4 seconds.
The front display shows
“Child-proof lock active”.
The button lock has now been
activated.
If a button is pressed during the
programme, “Child-proof lock
active” appears on the front
display. It is not possible to
cancel the programme (reset).
To deactivate the button lock,
press the F button for around
4 seconds until “Child-proof
lock active” disappears from
the front display.
The button lock is cancelled
automatically at the end of the
programme. In the event of a
power failure, the button lock
will be maintained. You need to
reactivate the button lock at the
beginning of every programme.
* depending on the features of
your dishwasher
8
Safety instructions en
Damage
■ The appliance may be
repaired and opened up by a
technician only. To do this,
disconnect the appliance
from the power supply. Pull
out the mains plug or switch
off the fuse. Turn off the tap.
■ If the appliance is damaged,
especially the control panel
(cracks, holes, broken
buttons), or the door function
is impaired, stop operating
the appliance. Pull out the
mains plug or switch off the
fuse. Turn off tap, call
customer service.
Disposal
1. Make redundant appliances
unusable to prevent
subsequent accidents.
2. Dispose of the appliance in
an environmentally friendly
manner.
:Warning
Risk of injury!
■ To prevent injuries, e.g.
caused by stumbling, open
the dishwasher only briefly in
order to load and unload the
dishwasher.
■ Knives and other utensils
with sharp points must be
placed with the points
downwards in the cutlery
basket*9" or horizontally
on the knife shelf* or in the
cutlery drawer*1*.
■ Do not lean or sit on the
open door.
■ In the case of free-standing
appliances, ensure that the
baskets are not overloaded.
The appliance could tip.
■ If the appliance is not in a
cavity and a side panel is
accessible, the door hinge
area must be covered at the
side for reasons of safety
(risk of injury). The covers
are available as optional
accessories from customer
service or specialist outlets.
* depending on the features of
your dishwasher
:Warning
Risk of explosion!
Do not add any solvents to the
rinsing compartment. Danger of
explosion!
:Warning
Risk of scalding!
Open the door carefully when
the programme is still running.
There is a risk of hot water
spraying out of the appliance.
:Warning
Risk to children!
■ If fitted, use the childproof
lock.
■ Do not allow children to play
with or operate the
appliance.
9
en Environmental protection
■ Keep children away from
detergents and rinse aid.
These may cause chemical
burns in the mouth, throat
and eyes or asphyxiation.
■ Keep children away from
open dishwasher. There may
be small parts in the
dishwasher which children
could swallow and the water
inside the dishwasher is not
drinking water as it may
contain detergent residue.
■ Ensure that children do not
place fingers in the tablet
collecting tray 1B. Small
fingers could become caught
in the slots.
■ When opening and closing
the door on an eye-level
appliance, ensure that
children do not become
jammed or crushed between
the appliance door and the
cupboard door below.
■ Children could become
locked in the appliance
(danger of suffocation) or get
into another dangerous
situation.
Redundant appliances: Pull
out the mains plug, sever
and dispose of the power
cord. Destroy the door lock
so that the door can no
longer be closed.
7 Environmental
protection
Environmental protection
Both the packaging of new appliances
and the old appliances themselves
contain valuable raw materials and
recyclable materials.
Please dispose of the individual parts
separated according to type.
Please ask your dealer or inquire at
your local authority about current means
of disposal.
Packaging
All plastic parts of the appliance are
identified with internationally
standardised abbreviations (e.g. PS
polystyrene). Therefore, plastic waste
can be sorted out when the appliance is
being disposed of.
Please follow the safety instructions
under “Delivery” ~ Page 5.
Old appliances
Please follow the safety instructions
under “Disposal of your appliance”
~ Page 9.
This appliance has been
identified in accordance with the
European Directive 2012/19/EU
on Waste Electrical and
Electronic Equipment (WEEE).
The directive provides a
framework for the collection and
recycling of old appliances,
which is valid across the EU.
10
Getting to know your appliance en
* Getting to know your
appliance
Getting to know your appliance
Diagrams of the control panel and the
interior of the appliance can be found at
the front of the manual. Individual
positions are referred to in the text.
Control panel
( On/off switch
0 Programme buttons **
8 Rinse aid refill indicator
@ Salt refill indicator
H WLAN display
P Selection buttons
X Time preselection
` Info button {
h Remote start button
)" START button
)* Additional functions/programme
buttons **
)2 < > button
): Door opener
)B Front display *
* depending on the features of your
dishwasher
** number depending on the features of
your dishwasher
Appliance interior
1" Interior light *
1* Cutlery drawer *
12 Top basket
1: Upper spray arm
1B Tablet collecting tray
1J Intake opening
1R Blow opening (Zeolith container)
1Z Lower spray arm
1b Dispenser for special salt
1j Filters
9" Cutlery basket *
9* Bottom basket
92 Dispenser for rinse aid
9: Detergent dispenser
9B Lock for detergent dispenser
9J Rating plate
* depending on the features of your
dishwasher
11
en Getting to know your appliance
Info button {
Info button
The Info button { can be used to
display additional programme
information.
1. Press the Info button {`.
2. Press the programme button.
The front display )B shows
information about the selected
programme.
3. To leave, press the Info button {
`.
Time setting
Time setting
When the appliance is switched on for
the first time, the time starts at 12:00
o’clock.
Set the time as follows:
1. Switch on ON/OFF switch (.
2. Press and hold the Info button {
` for 3 seconds until the following
text appears on the front display
)B:
Scroll with < >
Set with - +
Leave with Setup 3 sec.
3. Press the > )2 button repeatedly
until Time setting appears on the
front display )B.
4. Adjust the setting using the setting
buttons + and -P. You can hold
down the setting buttons - +P to
change the set values in 10-minute
steps.
5. Press Info button {` for 3
seconds.
The chosen setting has now been
stored.
Note: If the appliance was
disconnected from the power supply for
a prolonged period, the time starts at
12:00 o’clock. Set the time.
12
Initial start-up
Getting to know your appliance en
When the dishwasher is switched on for
the first time, you are taken directly to
the settings for the initial start-up.
Note: If you select Home Connect
during the initial start-up, make further
settings via your dishwasher app.
Observe the supplied Home Connect
documents for this.
The following text appears on the front
display )B:
Scroll with < >
The required settings for the initial
start-up are listed in the table below.
Change the setting as follows:
1. Press the > )2 button repeatedly
until the required setting is
displayed.
2. Adjust the setting using the setting
buttons + and - P.
3. Press and hold the Info button {
` for 3 seconds.
The chosen setting has now been
stored.
Set with - +
Leave with Setup 3 sec.
Initial start-up settingsFactory settingInfotext
by pressing Info button {
Sprache/LanguageDeutschLanguage selection.
Home ConnectManual/Home Connect Manual/Home Connect.
Time format24 h12h or 24h.
Time setting12:00Set the current time.
Water hardness°E 16 - 20 mediumAdjustment to the local water hardness.
When using Multitabs, select the lowest
setting.
Rinse aid disp.Level 5Amount of rinse aid affects drying. When
using Multitabs, select setting 0.
Water connection *Cold waterConnection to hot water (40-60°C) or cold
water (<40°C) possible.
* depending on the features of your dishwasher
--------
13
en Getting to know your appliance
Settings
The dishwasher has been preset with
certain settings for your convenience.
You can change these factory settings.
Change the setting as follows:
1. Switch on ON/OFF switch (.
2. Press and hold the Info button {
` for 3 seconds until the following
text appears on the front display
)B:
Scroll with < >
Set with - +
Leave with Setup 3 sec.
3. Press the > )2 button repeatedly
until the required setting is
displayed.
SettingFactory settingInfotext;
Time setting12:00Set the current time.
Time format24 h12 h or 24 h.
Time displayTimeShow end of programme with display
Language/LanguageDeutschLanguage selection.
Water hardness°E 16 - 20 mediumSetting water hardness.When using
Rinse aid dispenserLevel 5The amount of rinse aid affects drying.
Sensor settingStandardAdjustment of soiling detection for
Extra DryoffImproved drying for glasses and
Water connection *Cold waterConnection to hot water (40-60°C) or cold
Eco forecastoffShow the water and energy consumption.
Auto Power OffAfter 1 minuteAppliance automatically switches off at
Emotion Light *onInterior light.
Start programmeEco 50°After turning on, the last selected
* Depending on the configuration of your specific dishwasher
4. Adjust the setting using the setting
buttons + and - P.
5. Press Info button {` for 3
seconds.
The chosen setting has now been
stored.
You have the option of resetting all
changed settings back to the original
factory settings.
Note: When you reset your dishwasher
to the factory settings, you are taken
directly to the settings for switching on
the appliance for the first time.
by pressing Info button {
“Finish in” or “Finish at”.
Multitabs, select the lowest setting.
When using Multitabs, select setting 0.
optimum cleaning result.
plasticware.
water (<40°C) possible.
the end of each wash.
programme appears.
14
Getting to know your appliance en
SettingFactory settingInfotext;
by pressing Info button {
Tone volume *Level 2Volume of signal at end of programme.
Button volumeLevel 2Volume when using buttons.
Eco drying *onDoor opens automatically at end of Eco
programme.
Wi-Fion/offSwitch wireless network connection
on/off.
Network loginManual/AutomaticCheck WPS function on router.
No WPS function: Manual
WPS function: Autom./WPS
Connect to AppStart with +Connect dom. appliance to mobile
terminal device.
Energy manager *Connect with +Connect dom. appliance to energy
manager of home system.
GreetingonWhen switching on the appliance, the
brand logo can be turned off.
Factory settingResetResetting to the factory setting.
* Depending on the configuration of your specific dishwasher
Notes
■ The “Network login” menu option is
not available unless Wi-Fi has been
switched on.
■ The “Connect to App” menu option
■ The “Energy manager” menu option
is not available unless there is a
connection to the home network and
the appliance is connected to the
app.
is not available unless there is a
connection to the home network.
--------
15
en Home Connect
o Home Connect
Home Connect
If Home Connect services are available
in your country, you can use the "Home
Connect" function. You can find more
information at: www.home-connect.com
This dishwasher is Wi-Fi capable and
can be controlled remotely via a mobile
device. You can also operate your
dishwasher manually without a home
network connection using the control
panel.
Info button {
Info button
The Info button { can be used to
display additional programme
information.
1. Press the Info button {`.
2. Press the programme button.
The front display )B shows
information about the selected
programme.
3. To leave, press the Info button {
`.
Setting up the App
To be able to operate the appliance via
Home Connect, the Home Connect App
must be installed on your mobile
terminal device.
Observe the supplied Home Connect
documents.
Follow the steps specified by the App to
make the settings.
Setting up Home Connect
You can set your dishwasher by
pressing the remote start button }h
or proceed as follows:
1. Switch on ON/OFF switch (.
2. Press and hold the Info button {
` for 3 seconds until the following
text appears on the front display
)B:
Scroll with < >
Set with - +
Leave with Setup 3 sec.
3. Press the > )2 button repeatedly
until the required setting appears on
the front display )B.
4. Adjust the setting using the buttons
+ and - P.
5. Press Info button {` for 3
seconds.
The chosen setting has now been
stored in your dishwasher.
Wi-Fi |
Wi-Fi
In the Wi-Fi menu you can activate the
wireless network connection with “on”
and deactivate it with “off”.
!
Notes
■ If you have selected the Wi-Fi “off”
setting, the “Network login” and
“Connect to App” settings are not
available.
■ Remote control of the appliance
requires a stable wireless network
connection.
:L)L
RQ
16
Home Connect en
Network login
The “Network login” menu option is not
available unless you have activated
Wi-Fi.
In the “Network login” menu, you can
select between “Autom./WPS” and
“Manual” to connect the dishwasher to
your home network.
1HWZRUNORJLQ
!
0DQXDO$XWRP:36
Automatic: Connect to the home
network using the WPS function of your
router.
3UHVV:36EXWWRQ
RQWKHURXWHU
Manual: Connect your mobile terminal
device to the Home Connect network.
The network settings are then manually
entered using the Home Connect App
to connect to your home network.
After a successful connection, the
following text appears on the front
display )B:
1HWZRUNORJLQ
6XFFHVVIXO
Observe the supplied Home Connect
documents.
PV
Connect to App
The “Connect to App” menu option is
not available unless there is a
connection to the home network.
The “Connect to App” setting
establishes the link between the
dishwasher, app and your user account.
&RQQHFWWR$SS
!
6WDUWZLWK
After a successful connection, the
following text appears on the front
display )B:
&RQQHFWWR$SS
6XFFHVVIXO
Observe the supplied Home Connect
documents.
About data protection:
When your Home Connect dishwasher
is connected for the first time to a WLAN
network, which is connected to the
Internet, your Home Connect
dishwasher transmits the following
categories of data to the Home Connect
server (initial registration):
■ Unique appliance identification
(consisting of appliance codes as
well as the MAC address of the
installed Wi-Fi communication
module).
■ Security certificate of the Wi-Fi
communication module (to ensure a
secure IT connection).
■ The current software and hardware
version of your dishwasher.
■ Status of any previous resetting to
factory settings.
17
en Home Connect
This initial registration prepares the
Home Connect functions for use and is
activated the first time you use these
Home Connect functions. Please ensure
that the Home Connect functions can
be used only in conjunction with the
Home Connect App. Information on
data protection can be accessed in the
Home Connect app.
Remote start button }
Remote start button
When the dishwasher is connected to
the home network, activate the
dishwasher remote control by pressing
the remote start button }h.
If the dishwasher has still not logged
into Home Connect, access the Home
Connect settings by pressing the
remote start button }h.
Observe the supplied Home Connect
documents.
Notes
■ When the login process is complete,
the remote start button }h goes
out
■ To activate the remote control, press
the remote start button }h.
■ If the Home Connect Assistant was
aborted during start-up, press the
remote start button }h again.
■ If the connection to the router fails,
the WLAN H display flashes on
the display.
Wi-Fi without a connection to
the Home Connect server †
Wi-Fi without a connection to the Home Connect server
You can use the Home Connect app to
disconnect from the Home Connect
server.
The appliance is then locally connected
to your mobile device without however
any connection to the Home Connect
server.
Note: If you did not deactivate the
connection to the Home Connect
server, check your Internet connection.
Remote diagnostics …
Remote diagnostics
Customer Service can use Remote
diagnostics … to access your appliance
if you contact them.
Notes
■ You have to confirm Customer
Service access on your appliance.
■ You can switch off Remote
diagnostics … using the on/off
switch ( or deactivate Customer
Service access in the Home Connect
app.
Setting up
energy manager „ *
Setting up energy manager
With the energy manager „, your
dishwasher is automatically started
during a time period you select with the
cheapest power supply offered at the
time by your alternative energy source
(e.g. photovoltaic system).
If the energy manager „ is unable to
start the dishwasher remotely (for
example due to insufficient power
supply from the photovoltaic system), it
will start the dishwasher at the latest
possible time with a conventional power
supply.
18
Loading...
+ 40 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.