Siemens Rider 11, Rider 13 H,Rider 11 Bio,Rider 14 Pro,Rider 16 H,SIMATIC ET 200M,IM 153-4 PN,IM 153-2 HF Workshop Manual
Interface modules IM 153-4 PN and IM
153-2 HF
___________________
___________________
SIMATIC
ET 200M
Interface modules IM 153-4 PN and
IM 153-2 HF
Product Information
12/2013
A5E02714952
-04
Introduction
1
Product information
2
Siemens AG
Industry Sector
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E02714952-04
Ⓟ
01/2014 Technical data subject to change
Copyright © Siemens AG 2012 - 2013.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by
personnel qualified
for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
Interface modules IM 153-4 PN and IM 153-2 HF
Product Information, 12/2013, A5E02714952-04
3
Table of contents
1 Introduction ............................................................................................................................................. 5
2 Product information ................................................................................................................................. 7
2.1 Supplement to the sections ............................................................................................................ 7
2.2 The new functions for the IM 153-4 ............................................................................................. 10
Table of contents
Interface modules IM 153-4 PN and IM 153-2 HF
4 Product Information, 12/2013, A5E02714952-04
Interface modules IM 153-4 PN and IM 153-2 HF
Product Information, 12/2013, A5E02714952-04
5
1
Overview
This product information applies to:
● IM 153-4 PN interface module
– 6ES7153-4AA01-0XB0, as of firmware version 4.x
– 6ES7153-4BA00-0XB0, as of firmware version 4.x
● IM 153-2 HF interface module
– 6ES7153-2BA02-0XB0
– 6ES7153-2BA82-0XB0
Supplement to the ET 200M operating instructions
This product information is a supplement to the ET 200M
(http://support.automation.siemens.com/WW/view/en/1142798) operating instructions.
IM 153-4AA0x
The following changes have been made:
Property
6ES7153-4AA01-0XB0
6ES7153-4BA00-0XB0
Shared Device × ×
Media redundancy
×
×
Isochronous real-time communication
IRT option "high performance"
× ×
F modules — ×
Connection to H-CPUs with system
redundancy
— ×
HART modules — ×
Loading...