Siemens MXL Series, MXLV Series, MXL-RK1 Installation And Wiring Instructions

Download

Page 1

Fire Safety

Installation and Power Limited Wiring Instructions

Model MXL/MXLV Rack Mount Kits (RKs)

for ACM-RK, MKB-RK, MMB-RK, MOM-RK, MPS-RK, SYS-RK, TSP-RK, VSM-RK, and Cables-RK

INTRODUCTION

The Model RK series of panels and cables provides standard 19" rack mounting for MXL (without Voice) and MXLV (with Voice) modules. Table 1 lists the individual rack mount kits along with the specific modules that mount onto them.

TABLE 1

MXL/MXLV RACK MOUNT KITS

RACK MOUNT KIT

ACM-RK

MKB-RK MMB-RK MOM-RK

MPS-RK

SYS-RK TSP-RK VSM-RK

FILLER PLATE*

CABLES-RK (Required)

MOUNTS

MODULE(S)

ACM-1, MMM-1, PIM-1, TBM-1, and TMM-1

MKB-3, PIM-1 Front 12 1/4" X 19" MXL/MXLV MMB-1 or PSR-1 Rear 12 1/4" X 19" MXL/MXLV Up to 3 MOM-4s, MOM-2s,

OMM-1s, and/or OMM-2s Up to 2 MPS-6/-Ws and/or

MPS-12/-Ws EL-410D Rear 8 3/8" X 19" MXLV TSP-40 Front 12 1/4" X 19" MXL/MXLV Up to 6 VSM-1s, VLM-1s,

VFM-1s, and/or VSB-1s None Front As required x 19" MXL/MXLV

4 special cables for connecting modules

PLACEMENT

ON RACK

Front 17 1/2" X 19" MXLV

Rear 17 1/2" X 19" MXL/MXLV

Rear 8 3/4" X 19" MXL/MXLV

Front 7" X 19" MXLV

PANEL HEIGHT

X WIDTH

MXL/MXLV

TYPE OF

SYSTEM

* Filler plates can be purchased from any rack manufacturer. NOTE: Each MXL/MXLV module that is mounted must be ordered separately.

Siemens Building Technologies, Inc. 8 Fernwood Road Florham Park, New Jersey 07932

P/N 315-093402-9

Siemens Building Technologies, Ltd. 2 Kenview Boulevard Brampton, Ontario L6T 5E4 CN

Page 2

RACK HARDWARE

The MXL/MXLV rack mounting panels mount on a standard 19" wide x 18" deep rack (See Figure 1). Table 1 lists the recommended locations (front or rear) for the rack mounted modules and the panel heights of the rack mount kits.

The following rack is available for typical installations (Refer to Figure 1):

26"

MODEL

NO.

PART

NO.

DESCRIPTION

MXL-RK1 500-693470 6 Foot Vertical

Rack

The rack is supplied with:

• side, back, and top panels

• front door with clear lens

• battery tray

• mounting hardware

The front door door has a standard lock with key.

MODULE ASSEMBLY

Mount each module, except the MKB-3, the TSP-40, and the EL-410D to its designated rack mount kit (See Table 1) using the hardware and installation instructions provided with the module. See Table 2 for a list of installation instructions.

Refer to Figure 2 when assembling the ACM-RK to determine correct module placement and cabling connections.

MKB-3 Installation

Remove all system power before

installation, first battery and then AC.

(To power up, connect the AC first

and then the battery.)

Setting the Network Address (See Figure 3)

1. Before installing the MKB-3 panel, set its network address on S1, the switch on the ANN-1 board located on the back of the MKB-3. Use dipswitches SW1 and SW2 on

26"

Figure 1

MXL-RK1 Rack

TABLE 2

Installation

Instructions

ACM-1 315-092083 EL-410D 315-094916

MMB-1 MMB-2

MMM-1 315-092098 MOM-2 315-092777 MOM-4 315-090852 MPS-6/-W 315-090334/W MPS-12/-W 315-092030/W OMM-1 315-090267 OMM-2 315-092699 PIM-1 315-091462 PSR-1 315-090911 TSP-40 315-090776

VFM-1 VLM-1 VSM-1 VSB-1

Part

Number

315-090375 315-095097

315-092064 315-092064 315-092064 315-092064

Page 3

TBM-2

TMM-1

PIM-1

TO ANN-1 (MKB-RK)

NEW CABLE FROM CABLES-RK KIT

EXTENSION FROM CABLES-RK KIT

ACM-1

TO MMB-2

NEW CABLE FROM CABLES-RK KIT

switch S1 to set the network address of the MKB-3. Refer to Table 3 for switch settings.

2. The MKB-3 module address is always set within network addresses 248 through 251.

3. One supervised MKB-3 must be installed

at network address 251. Other supervised MKBs may be at the other addresses.

NOTE: Switches S1-SW3 and S1-SW4 are for

future use. Switch S1-SW5 is used to select supervision.

EXISTING MMM-1 CABLE

Figure 2 Rear View of the ACM-RK

MMM-1

ACM-RK

NOTE: When you select non-supervision for an

annunciator, there must also be one and only one supervised annunciator at the same address. The supervisory mode is independent of the network address.

TABLE 3

SWITCH SETTINGS ON THE ANN-1

Setting Supervision

Use switch S1-SW5 on the ANN-1 to select or deselect supervision. If your ANN-1 has a switch with position 1 indicated on the left-hand side, ignore the printing on the switch. SW1 on S1 is at the extreme right-hand side of S1, regardless of any other marking.

To set for supervision

S1-SW5 = Closed (ON)

To set for non-supervision

S1-SW5 = Open (OFF)

ADDRESS SETTINGS FOR:

SWITCH

S1-SW1

S1-SW2

S1-SW3

S1-SW4

S1-SW5

248 249 250 251

Open-

OFF

Open-

OFF

Closed-ONOpen-

OFF

Open-

Closed-ONClosed-

OFF

Closed-

Closed-ONClosed-ONClosed-ONClosed-

See Setting Supervision

Page 4

2. After installing the printer to the plate, mount the plate to the rack using hardware supplied with the rack. Refer to the SYSTEM ASSEMBLY section below and Figures 6 (with Voice) and 7 (without Voice), for the recommended location on the rack.

3. Mount the dress plate onto the rack with the clear lens centered over the printer paper. Fasten in place using hardware supplied with the rack.

SYS-RK Installation

Figure 3

Setting S1 on the ANN-1 Board

To assemble the MBK-RK:

1. Remove the four screws from the four standoffs on the rear side of the MKB-RK plate.

2. Position the MKB-3 panel over the four standoffs on the rear side of the MBK-RK plate, being sure that the MKB-3 panel fits into the cutout on the plate.

3. Replace the four screws on the standoffs and tighten them securely.

4. Mount the MKB-RK to its recommended location on the rack. Refer to Table 1 and Figures 6 and 7 to determine the correct location for your system.

The SYS-RK has two components (See Figure 5):

1. An 83/8 X 19" plate with studs.

2. A U-shaped plate with studs. To assemble the SYS-RK:

1. Mount the 8

/8 X 19" plate on the rear of the rack. Refer to the SYSTEM ASSEMBLY section and Figure 6 for the recommended location on the rack.

2. Place the six holes in the U-shaped plate over the six studs in the 19" rack plate. Secure the U-shaped plate in place using the six 8-32 nuts provided.

3. Install the EL-410D over the four studs on the U-shaped plate using the four 8-32 nuts provided.

TSP-40 Installation

The TSP-RK has two components:

1. U-shaped plate with studs (See Figure 4).

2. A dress plate with a clear lens. To assemble the TSP-RK:

1. Mount the TSP-40 printer to the studs using the hardware and installation instructions supplied with the printer. In this application, use the instructions for mounting the TSP-40 in an MBR-1 backbox.

STUDS

Figure 4

TSP-RK U-shaped Plate with Studs

Page 5

Figure 5

SYS-RK Components

SYSTEM ASSEMBLY

NOTE

Before installing the modules onto the rack, access to field wiring connections must be considered.

Refer to Figures 6 (with Voice) and 7 (without Voice) for the recommended placement of modules on the rack.

Observe the following conditions when mounting the modules onto the rack:

1. Modules having cable connections must be mounted close enough to each other so the cables will connect. In order to use the fixed length cables shipped with MXL/MXLV modules, place the modules on the rack in the same way that they are mounted in the MME-3 enclosure. Refer to the MXL/MXV Manual, P/N 315-092036, for mounting positions and cable connections.

2. Rear mounted modules must face the inside of the rack with the smooth side of the plate facing the back of the rack.

3. The ACM-RK must be mounted below the MKB-RK.

4. The MOM-RK must be mounted below the MMB-RK.

5. The MPS-RK must be mounted below the MOM-RK.

6. The MMB-RK must be mounted directly behind the ACM-RK.

7. The TSP-RK must be located within 24 inches of the MMB-RK.

8. The VSM-RK must be mounted directly below the ACM-RK.

Using the CABLES-RK Kit

The CABLES-RK kit (P/N 500-893044) has five cables for connecting modules. Four of the five cables replace cables that are shipped with modules. The remaining cable extends the length of the MMM-1 cable by plugging into it. Refer to Figures 2, 6, or 7, and Table 4 for specific cable use.

WIRING

All wiring must comply with national and local codes.

In compliance with UL-864, effective May 1, 1995, all power limited fire protective signaling conductors must be separated a minimum of 1/4 inch from all of the following items located within a control panel:

• electric light

• power

• Class 1 or non-power limited fire protective signaling conductors

Page 6

4ELBAT

TIKKR-SELBAC

)440398-005N/P(

ELBAC

EPYT

nobbiRrotcudnoC41VLXMsecalpeR1P,1-MCA

nobbiRrotcudnoC51VLXMsecalpeR4P,1-MCA

nobbiRrotcudnoC51ro"04

yrettaBeriW2VLXM/LXMsecalpeR2P,2/1-BMM

elbaCeriW9VLXMsdnetxE1-MMM

FOEPYT

METSYS

VLXMsecalpeR

LXMsecalpeR

SECALPER

SDNETXERO

STCENNOC

SELUDOM

3P,1-MMT

P,1-NNA

8P,2-BMM

P,1-MCA5

8P,2-BMM

P,1-NNA

yrettaB

7P,1-MCA

ELBAC

HTGNEL

"42

"06

To meet these requirements, two wire ducts are mounted along the sides of the rack assembly, as shown in Figure 8. Remove the wire duct cover, route all non-power limited wiring through the ducts, then snap the cover back in place.

Refer to the Installation and Power Limited Wiring Instructions for the MME-3 Backbox, P/N 315-

094883, for further information on power and non-power limited wiring.

NOTE: If power-limited wiring is not used within a

rack mount system, then the following guidelines do not apply. In that case, be sure to follow standard wiring practices.

Page 7

WIRING ENTERING THE RACK ASSEMBLY

Non-Power Limited Wiring

Wiring to the following MXL/MXLV module terminations shown in Table 5 is considered nonpower limited. The wiring must enter and exit the rack assembly through the bottom of the rack and route in either of the two ducts. Wiring between the ducts and the module terminations must be in the shortest route and must not overlap any other wiring.

TABLE 5

Module Termination

ASC-1/-2‡ (Power from EL-410D) Batteries

CRM-4* CSM-4† MMB-1/2 (P3) MPS-6/-W or MPS-12/-W ZC Zone Cards‡ (Power from EL-410D)

OMM-1 MMB-1/2 or

PSR-1 MOM-4 MOM-4 MOM-4 (P5) 1, 2, 3 OMM-1

TABLE 6

Module Termination

ALD-2 ALD-2I CMI-300 CSM-4* CZM-4 MMB-1/2

NET-4/7 NIM-1R PIM-1 PSR-1

OCC-1 REP-1 TBM-2

XLD-1 ZAC-30 ZCT-8B

* When the CSM-4 is used as Notification Application

Circuit or Leased Line.

MOM-4 MOM-4 MOM-4 MOM-4 MOM-4 TB1 (1-4) TB2 (1-4) TB3 (1-4) TB4 (1-9)† TB5 (1-12) MOM-4 TB1 TB1 (1-6)† TB4 (1-4) TB3 (1-4) OMM-1 MOM-4 TB4 (All positions) TB5 (All positions) MOM-4 OMM-1 OMM-1

* CRM-4/CSM-4 modules must be installed in the

extreme left MOM module position.

 When the CSM-4 is used as Municipal Tie or Releasing

Service.

 Audio or strobe power wiring to any ZC Zone Card

module and ASC-1/-2 first must be terminated at a PLC-4 plug-in module installed in an OMM-1 and then at the zone card. The PLC-4 must contain at least one of the following plug-on boards: a PL864-25A or PL864-70A for audio circuits, or a PL-864-25S for strobe circuits. Refer to the PLC-4 Installation Instructions, P/N 315-093312.

WIRING ENTERING THE RACK

Power Limited Wiring

Wiring to the following MXL module terminations shown in Table 6 is considered power limited and must enter the rack assembly through the bottom of the rack.

† Listed Class 2 or Power Limited Source.

SYSTEM WIRING

For systems without the voice option (MXL):

Connect the modules as shown in the individual installation instructions (Refer to Table 2) and the MXL/MXLV Manual, P/N 315-092036.

For systems with the voice option (MXLV):

Connect the modules as shown in the individual installation instructions (Refer to Table 2) and the MXL/MXLV Manual, P/N 315-092036.

For all systems:

After connecting the modules, complete the field wiring to each module following the individual installation instructions (Refer to Table 2) and the MXL/MXLV Manual, P/N 315-092036.

Page 8