This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
indicates that minor personal injury can result if proper precautions are not taken.
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
Trademarks
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
Siemens AG
Division Process Industries and Drives
Postfach 48 48
90026 NÜRNBERG
GERMANY
General approvals ............................................................................................................108
National approvals............................................................................................................114
Reference Manual, 01/2017, C79000-G8976-C392-05
Approvals SCALANCE W700 802.11n
5
Approvals for SCALANCE W780 / W740 802.11n
Note
Issued approvals on the type plate of the device
The specified approvals apply only when the corresponding mark is printed on the product.
You can check which of the following approvals have been granted for your product by the
markings on the type plate.
Range of validity
The approvals listed in this section apply to the following products:
Some approvals apply only to certain devices or series. In such situations, the designations
of the products are shortened to avoid having to list all the type designations. The following
table shows how the abbreviations relate to the product variants.
The EC Declaration of Conformity is available for all responsible authorities at:
Siemens Aktiengesellschaft
Process Industries and Drives Division,
Process Automation
DE-76181 Karlsruhe
Germany
You will find the current EC declaration of conformity for these products on the Internet
pages of Siemens Industry Online Support
(hhttps://support.industry.siemens.com/cs/ww/en/ps/15853/cert).
The SIMATIC NET products described in these Operating Instructions meet the
requirements of the following EC directives:
●
94/9/EC
Directive of the European Parliament and the Council of 23 March 1994 on the
approximation of the laws of the Member States concerning equipment and protective
systems intended for use in potentially explosive atmospheres (until 19.04.2016).
●
2014/34/EU
Directive 2014/34/EU of the European Parliament and of the Council of 26 February 2014
on the harmonization of the laws of the Member States relating to equipment and
protective systems intended for use in potentially explosive atmospheres official journal of
the EU L96, 29/03/2014, pages. 309–356 (as of 20.04.2016)
●
1999/5/EC
Directive of the European Parliament and of the Council of 1999 March 1999 on Radio
Equipment and Telecommunications Terminal Equipment and the mutual recognition of
their conformity (until 12.06.2016).
●
2014/53/EU
Directive of the European Parliament and of the Council of April 16, 2014 on the
harmonization of the laws of the member states relating to placing radio equipment on the
market.; official journal of the EU L153, 22/05/2014, pages. 62–106 (as of 13.06.2016)
● 2011/65/EU (RoHS)
RoHS directive of the European Parliament and of the Council of 8 June 2011 on the
restriction of the use of certain hazardous substances in electrical and electronic
equipment.
●
1999/519/EC
Council recommendation on the limitation of exposure of the general public to
electromagnetic fields (0 Hz to 300 GHz)
Reference Manual, 01/2017, C79000-G8976-C392-05
Approvals SCALANCE W700 802.11n
8
Approvals
for
SCALANCE
W780
/
W740
802.11n
1.1 EC declaration of conformity
1.1.1
ATEX
ATEX directive (correct usage in potentially explosive atmospheres)
The SIMATIC NET product meets the requirements of the EC directive:94/9/EC (until
19.04.2016) and 2014/34/EU (as of 20.04.2016) "Equipment and Protective Devices for Use
in Potentially Explosive Atmospheres" according to the standards listed in the section
Products (Page 10):
Applied standard:
1 EN 60079-0 + A11
Hazardous areas - Part 0: Equipment - General requirements
2 EN 60079-15
Explosive atmospheres - Part 15: Equipment protection by type of protection "n"
1.1.2
RoHS
RoHS directive (restriction of the use of certain hazardous substances)
The SIMATIC NET products described in these operating instructions meet the requirements
of the EC directive 2011/65/EC for the restriction of the use of certain hazardous substances
in electrical and electronic equipment:
1.1.3
1.1.3.1
Applied standard:
3 EN 50581
Technical documentation for the assessment electrical and electronic products with
respect to restriction of hazardous substances
R&TTE / RED
Protection of health and safety
Article 3 (1) a) protection of health and safety
4 EN 60950-1+A1+A2+A11+A12
Information technology equipment - Safety - Part 1: General requirements
5 EN 62311
Assessment of electronic and electrical equipment related to human exposure restrictions for electromagnetic fields (0 Hz – 300 GHz)
Railway applications - Electromagnetic compatibility - part 4: Interference emissions
and immunity of signal telecommunications equipment
8 ETSI EN 301 489-1
Electromagnetic compatibility and radio spectrum matters (ERM) - Electromagnetic
compatibility for radio equipment and services - Part 1 : Common technical requirements
9 ETSI EN 301 489-17
Electromagnetic compatibility and radio spectrum matters (ERM) - Electromagnetic
compatibility for radio equipment and services - Part 17 :
10 EN 61000-6-1
Electromagnetic compatibility (EMC) - Part 6-1: Generic standards - Immunity for
residential, commercial and light-industrial environments
11 EN 61000-6-2+AC
Electromagnetic compatibility (EMC) - Part 6-2: Generic standards - Immunity for
industrial environments
12 EN 61000-6-3+A1+AC
Electromagnetic compatibility (EMC) - Part 6-3: Generic standards - Emission
standard for residential, commercial and light-industrial environments
13 EN 61000-6-4+A1
Electromagnetic compatibility (EMC) - Part 6-4: Generic standards - Emission
standard for industrial environments
1.1.3.3
Reference Manual, 01/2017, C79000-G8976-C392-05
Efficient use of the radio spectrum
Art. 3 (2) Efficient use of the radio spectrum
14
ETSI EN 301 328
Electromagnetic compatibility and radio spectrum matters (ERM) - wideband
transmission systems - data transmission equipment operating in the 2.4 GHz ISM
band and using wideband modulation techniques. Harmonized EN containing the
essential requirements according to Article 3.2 of the R&TTE directive.
15
ETSI EN 301 893
Broadband Radio Access Networks (BRAN) - 5 GHz high performance RLAN -
Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive
Approvals
for
SCALANCE
W780
/
W740
802.11n
1.1 EC declaration of conformity
Approvals SCALANCE W700 802.11n
10
1.1.4
Products
Product designation and standards
The standards that apply to the product are described in RoHS (Page 8), ATEX (Page 8) and
R&TTE / RED (Page 8).
The following tables show the product names and the corresponding certification ID:
Type
W786-1 RJ-451 x RJ-45-3EAPN-W1-RJ-E3
W786-2 RJ-451 x RJ-45-6EAPN-W2-RJ-E3
W786-2IA RJ-451 x RJ-452-EAPN-W2-RJ-I3
W786-2 SFP2 x SFP-6EAPN-W2-SFP-E3
Type
W788-1 RJ-45RAPN-W1-RJ-E3
W788-2 RJ-45RAPN-W2-RJ-E3
W788-1 M12RAPN-W1-M12-E3
W788-2 M12RAPN-W2-M12-E3
W788-2 M12 EECRAPN-W2-M12-E3
W748-1 RJ-45RAPN-W1-RJ-E3
W748-1 M12RAPN-W1-M12-E3
Number and type of
the Ethernet interfaces
Certification ID
Article number:
Article number US variant
6GK 5788-1FC00-0AA0
6GK 5788-1FC00-0AB0
6GK5 788-2FC00-0AA0
6GK5 788-2FC00-0AB0
6GK5 788-1GD00-0AA0
6GK5 788-1GD00-0AB0
6GK5 788-2GD00-0AA0
6GK5 788-2GD00-0AB0
6GK5 788-2GD00-0TA0
6GK5 788-2GD00-0TB0
6GK5 748-1FC00-0AA0
6GK5 748-1FC00-0AB0
6GK5 748-1GD00-0AA0
6GK5 748-1GD00-0AB0
Number of internal antennas
Number of R-SMA
sockets for external
Certification ID
Article number
6GK5 786-1FC00-0AA0
6GK5 786-1FC00-0AB0
6GK5 786-2FC00-0AA0
6GK5 786-2FC00-0AB0
6GK5 786-2HC00-0AA0
6GK5 786-2HC00-0AB0
6GK5 786-2FE00-0AA0
6GK5 786-2FE00-0AB0
Reference Manual, 01/2017, C79000-G8976-C392-05
Approvals
for
SCALANCE
W780
/
W740
802.11n
1.2 General approvals
Approvals SCALANCE W700 802.11n
12
1.2
General approvals
ATEX (explosion protection directive)
WARNING
When using SIMATIC NET products in hazardous area zone 2, make absolutely sure that
the associated conditions in the following document are adhered to:
"SIMATIC NET Product Information Use of subasseblies/modules in a Zone 2 Hazardous
Area".
You will find this document
on the data medium that ships with some devices.
on the Internet pages of Siemens Industry Online Support
(http://support.automation.siemens.com/ww).
Enter the document identification number C234 as the search term.
The SIMATIC NET products meet the requirements of the EC directive 94/9/EC "Equipment
and Protective Devices for Use in Potentially Explosive Atmospheres”. and as of 20.04.2016
the EC directive 2014/34/EU.
ATEX classification:
IECEx
II 3 G Ex nA IIC T4 Gc
KEMA 07ATEX0145 X
The products meet the requirements of the following standards:
●
EN 60079-15 (electrical apparatus for potentially explosive atmospheres; Type of
protection "n")
●
EN 60079-0 (Explosive atmospheres - Part 0: Equipment - General requirements)
You will find the current versions of the standards in the currently valid ATEX certificates.
The SIMATIC NET products meet the requirements of explosion protection according to
IECEx.
IECEx classification:
Ex nA IIC T4 Gc
DEK 14.0025X
The products meet the requirements of the following standards:
●
IEC 60079-15 (Explosive atmospheres - Part 15: Equipment protection by type of
protection "n")
●
IEC 60079-0 (Explosive atmospheres - Part 0: Equipment - General requirements)
You will find the current versions of the standards in the currently valid IECEx certificates.
Reference Manual, 01/2017, C79000-G8976-C392-05
Approvals
for
SCALANCE
W780
/
W740
802.11n
Approvals SCALANCE W700 802.11n
13
FM
The product meets the requirements of the standards:
●
Factory Mutual Approval Standard Class Number 3611
●
FM Hazardous (Classified) Location Electrical Equipment:
Non Incendive / Class I / Division 2 / Groups A,B,C,D / T4 and
Non Incendive / Class I / Zone 2 / Group IIC / T4
cULus Approval for Information Technology Equipment
cULus Listed I. T. E.
Underwriters Laboratories Inc. complying with
●
UL 60950-1 (Information Technology Equipment)
● CSA C22.2 No. 60950-1-03
Report no. E115352
Note
Only devices of the SCALANCE W786-x series have this approval.
1.2 General approvals
cULus Approval Hazardous Location
cULus Listed I. T. E. FOR HAZ. LOC.
Underwriters Laboratories Inc. complying with
●
UL 60950-1 (Information Technology Equipment)
● ANSI/ISA 12.12.01-2007
● CSA C22.2 No. 213-M1987
Approved for use in
Cl. 1, Div. 2, GP A, B, C, D T4
Cl. 1, Zone 2, GP IIC T4
Report no. E240480
Reference Manual, 01/2017, C79000-G8976-C392-05
Approvals
for
SCALANCE
W780
/
W740
802.11n
1.2 General approvals
Approvals SCALANCE W700 802.11n
14
FCC approval
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1)
(2)
undesired operation.
Notice
Changes or modifications made to this equipment not expressly approved by SIEMENS may
void the FCC authorization to operate this equipment.
IEEE 802.11b or g operation of this product in the USA is firmware-limited to channels 1
through 11.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
●
●
●
●
this device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV technician for help.
Notice
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20 cm
between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter. Professional Installation Notice:
To comply with FCC part 15 rules in the United States, the system must be professionally
installed to ensure compliance with the Part 15 certification. It is the responsibility of the
operator and professional installer to ensure that only certified systems are deployed in the
United States. The use of the system in any other combination (such as co-located antennas
transmitting the same information) is expressly forbidden.
Reference Manual, 01/2017, C79000-G8976-C392-05
Approvals
for
SCALANCE
W780
/
W740
802.11n
1.2 General approvals
Approvals SCALANCE W700 802.11n
15
Notice
For use of DFS channels
●
Use of the RCoax Cable Antenna 6XV1875-2D is not permitted in channels which
require dynamic frequency selection (DFS).
●
Any installation of either a master or a client device within 35 km of a TDWR (Terminal
Doppler Weather Radar) location shall be separated by at least 30 MHz (center-to-center)
from the TDWR operating frequency.
These devices shall be registered in the industry sponsored WISPA database,
When you open this link, you get the following choices:
–
"Search" opens a window with TDWR locations and frequencies.
–
"User Signup" allows you to register as user of the database.
–
After registering you can Logon and register your WLAN location. Please fill in all
required information.
For more information with respect to WISPA database and TWDR locations please consult
FCC publication KDB 443999 D01.
NEMA TS2
The product meets the requirements of the standard
NEMA TS2 (Traffic Controller Assemblies with NTCIP Requirements)
SCALANCE W788-2 M12 EEC
RSS-247 of Industry Canada for SCALANCE W786-x
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that
may cause undesired operation of the device.
This radio transmitter (IC: 267AA-MPCIE1V1) has been approved by Industry Canada to
operate with the antenna types listed in section 6.8 with the maximum permissible gain and
required antenna impedance for each antenna type indicated. Antenna types not included in
this list, having a gain greater than the maximum gain indicated for that type, are strictly
prohibited for use with this device.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna
of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To
reduce potential radio interference to other users, the antenna type and its gain should be so
chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that
necessary for successful communication.
6GK5788-2GD00-0TA0
6GK5788-2GD00-0TB0
Reference Manual, 01/2017, C79000-G8976-C392-05
Approvals
for
SCALANCE
W780
/
W740
802.11n
1.2 General approvals
Approvals SCALANCE W700 802.11n
16
To reduce potential radio interference to other users, the antenna type and its gain should be
so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that
permitted for successful communication.
That the device for the band 5150-5250 MHz is only for indoor usage to reduce potential for
harmful interference to co-channel mobile satellite systems.
Users should also be cautioned to take note that high power radars are allocated as primary
users (meaning they have priority) of 5250-5350 MHz and 5650-5850 MHz and these radars
could cause interference and/or damage to LE-LAN devices.
This equipment complies with IC RSS-102 radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with minimum
distance 20cm between the radiator & your body.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1)
l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
RSS-247 of Industry Canada for SCALANCE W7x8
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that
may cause undesired operation of the device.
This radio transmitter (IC: 267AA-MPCIE1V1) has been approved by Industry Canada to
operate with the antenna types listed in section 5.4 with the maximum permissible gain and
required antenna impedance for each antenna type indicated. Antenna types not included in
this list, having a gain greater than the maximum gain indicated for that type, are strictly
prohibited for use with this device.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna
of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To
reduce potential radio interference to other users, the antenna type and its gain should be so
chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that
necessary for successful communication.
To reduce potential radio interference to other users, the antenna type and its gain should be
so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that
permitted for successful communication.
That the device for the band 5150-5250 MHz is only for indoor usage to reduce potential for
harmful interference to co-channel mobile satellite systems.
Users should also be cautioned to take note that high power radars are allocated as primary
users (meaning they have priority) of 5250-5350 MHz and 5650-5850 MHz and these radars
could cause interference and/or damage to LE-LAN devices.
This equipment complies with IC RSS-102 radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with minimum
distance 20cm between the radiator & your body.
Reference Manual, 01/2017, C79000-G8976-C392-05
Approvals
for
SCALANCE
W780
/
W740
802.11n
Approvals SCALANCE W700 802.11n
17
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1)
l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
Note for USA, Canada, Puerto Rico, Peru, Bahamas, Ecuador and Columbia
When operating the SCALANCE W700 with DFS (Dynamic Frequence Selection), the
IWLAN RCoax Cable 5 GHz (order number 6XV1875-2D) may not be used in the countries
listed above.
Approvals in Argentina
Devices of the SCALANCE W786-x series are approved in Argentina under the following
certification numbers:
The listed devices are approved in Brazil under the following certification numbers:
Reference Manual, 01/2017, C79000-G8976-C392-05
Approvals
for
SCALANCE
W780
/
W740
802.11n
1.2 General approvals
Approvals SCALANCE W700 802.11n
18
Este equipamento opera em caráter secundário, isto, ist é, não tem direito à proteção contra
interferência prejudicial, mesmo de estações do mesmo tipo e não pode causar interferência
a sistemas operando em caráter primário.
From the SCALANCE W7x8 series, the following devices are approved for Brazil:
The listed devices are approved in Brazil under the following certification numbers:
Este equipamento opera em caráter secundário, isto, ist é, não tem direito à proteção contra
interferência prejudicial, mesmo de estações do mesmo tipo e não pode causar interferência
a sistemas operando em caráter primário.
The WLAN modules included in the devices have the following certification number:
RCPSIMP12-0751
Approval for Oman
1.2 General approvals
주의하시기 바라며, 가정외의 지역에서 사용하는
것을 목적으로 합니다.
Devices of the SCALANCE W786-x series are approved in Oman under the following
certification numbers:
OMAN-TRA
R/1773/14
D090258
Devices of the SCALANCE W788-x series are approved in Oman under the following
certification numbers:
OMAN-TRA
R/1772/14
D090258
NCC Warning Statement (Taiwan)
Article 12
Without permission, any company, firm or user shall not alter the frequency, increase the
power, or change the characteristics and functions of the original design of the certified lower
power frequency electric machinery.
Article 14
The application of low power frequency electric machineries shall not affect the navigation
safety nor interfere a legal communication, if an interference is found, the service will be
suspended until improvement is made and the interference no longer exists.
Reference Manual, 01/2017, C79000-G8976-C392-05
Approvals
for
SCALANCE
W780
/
W740
802.11n
1.2 General approvals
Approvals SCALANCE W700 802.11n
20
Marking for the customs union
EAC (Eurasian Conformity)
Customs union of Russia, Belarus and Kazakhstan
Declaration of the conformity according to the technical regulations of the customs union
(TR CU)
Reference Manual, 01/2017, C79000-G8976-C392-05
Approvals SCALANCE W
700 802.11n
21
Approvals
for
SCALANCE
W780
/
W740
802.11n
1.3 National approvals
1.3
National approvals
The following table lists the countries in which the SCALANCE W700 product is approved.
The diamond symbol (♦) identifies all countries for which there was no approval at the time
these operating instructions were written.
The current status of the approvals can be found on the Internet at the following address:
http://www.siemens.com/funkzulassungen
ColumnMeaning
CountryCountry
ModeIEEE 802.11 standard and the TPC and / or DFS functionality, where required
CHChannel
MHzFrequency
PWR (EIRP)Maximum permitted effective isotropic radiated power
UsePermitted use indoors and / or outdoors
Reference Manual, 01/2017, C79000-G8976-C392-05
Approvals
for
SCALANCE
W780
/
W740
802.11n
1.3 National approvals
Approvals SCALANCE W700 802.11n
22
Belgium
-
-
zegovina
100
5500
1000 mW
Indoor + outdoor
-
-
116
5580
Iceland
Malta
Monaco
Netherlands
Norway
Poland
Romania
Sweden
Slovakia
Spain
Turkey
Vatican
Cyprus
CountryModeCHMHzPWR
(EIRP)
Andorra11g 11n12412100 mW Indoor + outdoor
Bosnia and Her-132472
Bulgaria
Denmark
Germany
Estonia
Finland
France
Greece
Great Britain
Ireland