Page 1
Installation Instructions
Model FMT-A-ADPT
Class A Riser Module for the FMT
INTRODUCTION The Model FMT-A-ADPT module (as shown in Figure 1) from Siemens
Industry, Inc., provides the FMT with Class A riser capability. The
telephone riser is supervised by the primary FMT.
PRE-INSTALLATION The FMT-A-ADPT is shipped with the bracket for use on the CC-2 or
CC-5 Card Cages attached to the FMT-A-ADPT board.
TT
o use the FMTo use the FMT
T
o use the FMT
TT
o use the FMTo use the FMT
Slot 1 (tSlot 1 (t
Slot 1 (t
Slot 1 (tSlot 1 (t
Cage yCage y
Cage y
Cage yCage y
erminals 9-1erminals 9-1
erminals 9-1
erminals 9-1erminals 9-1
ou must place it in Slot 5 (tou must place it in Slot 5 (t
ou must place it in Slot 5 (t
ou must place it in Slot 5 (tou must place it in Slot 5 (t
The FMT-A-ADPT is shipped with two removable terminal plugs
(see Figures 5 and 6) that are installed in J1 and J2. Remove the
terminal plug from the CC-5/CC-2 header (terminals 9-16) where the FMT-A-ADPT will
be installed. Transfer the existing field wiring in the connector to connector J2 as
explained in the wiring section and discard the connector that was removed.
-A-ADPT on a CC-2 Card Cage,-A-ADPT on a CC-2 Card Cage,
-A-ADPT on a CC-2 Card Cage,
-A-ADPT on a CC-2 Card Cage,-A-ADPT on a CC-2 Card Cage,
6) of the top Double Header; on a CC-5 Card6) of the top Double Header; on a CC-5 Card
6) of the top Double Header; on a CC-5 Card
6) of the top Double Header; on a CC-5 Card6) of the top Double Header; on a CC-5 Card
erminals 9-1erminals 9-1
erminals 9-1
erminals 9-1erminals 9-1
y y
ou must place it inou must place it in
y
ou must place it in
y y
ou must place it inou must place it in
6) of the top Double Header6) of the top Double Header
6) of the top Double Header
6) of the top Double Header6) of the top Double Header
FMT-A-ADPT
12345678
J1
E6
16
16
1
E2
E3
E4
E7
E5
J4
9
J2
9
J3
Figure 1
FMT-A-ADPT PCB
..
.
..
INSTALLATION
Remove all system power before installation, first battery then AC. (To power up,
connect the AC first, then the battery.)
Install the FMT-A-ADPT (Refer to Figure 2) in the top header of the CC-5/CC-2. Insert
the female plug on the end of the FMT-A-ADPT into the appropriate top header (Slot 5
CC-5 CARD CAGE
SLOT FOR CAPTIVE
SCREW IN SLOT 1 OF
CC-2 TOP DOUBLE HEADER
SLOT FOR CAPTIVE
SCREW IN SLOT 5 OF
CC-5 TOP DOUBLE HEADER
CAPTIVE SCREW
INSTALL FMT-A-ADPT
MODULE IN SLOT 5
OF CC-5 CARD
CAGE, AS SHOWN.
FOR CC-2 CARD CAGE,
INSTALL
FMT-A-ADPT
MODULE IN SLOT 1
AND USE THIS SPACE
FOR CAPTIVE SCREW.
ANY XLS SINGLE
SLOT MODULE
Figure 3
FMT-A-ADPT Installed in CC-5
CC-5 TOP DOUBLE
HEADER
FMT-A-ADPT MODULE
PLUGS INTO TOP
DOUBLE HEADER OF
SLOT 5 OF CC-5 OR
SLOT 1 OF CC-2 CARD
CAGE.
CC-5 BOTTOM
HEADER
Figure 2
FMT-A-ADPT
J1
J4
J2
J3
(FEMALE PLUG)
P/N 315-050338-0
Building Building
Building
Building Building
Siemens Siemens
Siemens
Siemens Siemens
TT
ecec
hnologies Dihnologies Di
T
ec
hnologies Di
TT
ecec
hnologies Dihnologies Di
IndustryIndustry
Industry
IndustryIndustry
visionvision
vision
visionvision
,,
Inc. Inc.
,
Inc.
,,
Inc. Inc.
Page 2
for CC-5 or Slot 1 for CC-2) and then secure the retaining bracket under the XLS
module’s retaining captive screw that shares the space. Do not put the FMT-A-ADPT
under the bezel of the XLS module. (Refer to Figure 3.)
WIRING A 46-inch long 10-wire audio cable, P/N 555-150509, connects the FMT-A-ADPT to
the FMT to provide Class A riser capability. One end of this wire plugs into J4 of the
FMT-A-ADPT and the other end plugs into JP1 of the FMT. The connectors are keyed
and fit only one way. Make sure that all cables seat fully into their connectors.
Transfer any existing field wiring that was in positions 9-16 of the terminal block
header to the corresponding position on J2.
The screw terminals for J2 can accommodate one 12-22 AWG or two 16-24 AWG
(stranded only). For J1, the screw terminals can accommodate one 12-22 AWG or
two 16-18 AWG (stranded only). All wiring to the FMT-A-ADPT is power limited.
FEED
+
1234 5678
RETURN
-
+
NO CONNECTION
-
J1
Figure 4
Wiring to J1
To Connect External Wiring 1. Insert the wire to be connected in the desired opening in the side of the remov-
able terminal block.
2. Tighten the appropriate locking screw.
3. Insert the removable terminal block in the appropriate header (J1 or J2) on the
FMT-A-ADPT.
POSITION 8
LOCKING SCREWS
POSITION 1
OPENING IN
SIDE FOR WIRE
CONNECTION
LOCKING SCREWS
POSITION 16
OPENING IN
SIDE FOR WIRE
CONNECTION
ELECTRICAL RATINGS
Siemens Industry, Inc.
Building Technologies Division
Florham Park, NJ
Figure 5
Plug for J1 (Positions 1-8)
tnerruCenalPkcaBV420
tnerruCV42lanimreTwercS
tnerruCenalPkcaBV2.60
tnerruCybdnatSV420
Siemens Building Technologies, Ltd.
Fire Safety & Security Products
2 Kenview Boulevard
Brampton, Ontario
L6T 5E4 Canada
POSITION 9
Figure 6
Plug for J2 (Positions 9-16)
,snoitcurtsnInoitallatsnITMFehtotrefeR
nonoitamrofnirof,001430-513N/P
.TMFehtrofsgnitarlacirtcele
P/N 315-050338-0
Loading...